S911 Lola User Manual Version 1.10 September 6, 2012
(Preliminary) Copyright 2012 by Laipac Technology Inc. Laipac Technology Inc. Federal Communications Commission (FCC) Statement Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End user must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. The portable device is designed to meet the requirements for exposure to radio waves established by the Federal Communications Commission (USA). These requirements set a SAR limit of 1.6 W/kg averaged over one gram of tissue. The highest SAR value reported under this standard during product certification for use when properly worn on the body is 0.754W/kg W/kg,Head is 0.919 W/kg. EU regulatory conformance (CE) Laipac Technology Inc hereby declares that this tracking device is in compliance with the essential requirements and other relevant provision of Directive 1999/5/EC. Additional regulatory conformance Specific details about compliance to the following standards and regulatory bodies may be obtained from Laipac Technology Inc. PCS Type Certification Review Board (PTCRB) 20 Mural Street, Unit 5, Richmond Hill Ontario L4B 1K3 Canada 2 Tel: 905-762-1228 | Fax: 905-763-1737 | E-mail: info@laipac.com | http://www.laipac.com Laipac Technology Inc. Based on Cellular Telecommunications and Internet Association (CTIA) Over the Air (OTA) performance tests EN 301 511, EN 300 440, EN 62311, EN 301 489-1-3-7 and 60950-1 testing. CONTENTS Chapter 1: For Your Safety 1.1 About Your Device 1.2 Network Services 1.3 Care and Maintenance Chapter 2: Introduction 2.1 Welcome 2.2 Main Features Chapter 3: Specification 3.1 Electrical & Environmental Specs 3.2 GPS Engine Specification 3.3 GSM Module Specification Chapter 4: SIM Card and Its Installation 4.1 Requirement for SIM Card 4.2 Installation of SIM Card Chapter 5: Configuration, Upgrading and Utility 5.1 Introduction to Laipac Suite 5.2 Usage of Laipac Suite Chapter 6: Operation Instructions 6.1 Knowing about your Lola 6.2 Function Button and Its Related Operation 6.3 LED Indicators and Lolas Working Status 20 Mural Street, Unit 5, Richmond Hill Ontario L4B 1K3 Canada 3 Tel: 905-762-1228 | Fax: 905-763-1737 | E-mail: info@laipac.com | http://www.laipac.com
- Chapter 1 -
For Your Safety Laipac Technology Inc. Read these simple guidelines below. Not following them may be dangerous or illegal. Read the complete user guide for further information. Road Safety Comes First Do not use the device for talk and text when wireless phone use is prohibited or when it may cause danger. Interference All wireless devices may be susceptible to interference, which could affect performance. Switch Off In Hospitals Switch the device off near medical equipment. Switch Off In Aircraft Follow any restrictions. Wireless devices can cause interference in aircraft. Switch Off When Refuelling Do not use the device at a refueling point. Do not use near fuel or chemicals. Switch Off Near Blasting Follow any restrictions. Do not use the device where blasting is in progress. Qualified Service Only qualified personnel may open or repair this product. Batteries Use only approved batteries. Do not connect to incompatible products. Back Up Copies It is recommended to save important settings. Connecting To Other Devices When connecting to any other device, read its user guide for detailed safety instructions. Do not connect with incompatible products. Emergency Calls Ensure the phone function of the device is switched on and in service. 20 Mural Street, Unit 5, Richmond Hill Ontario L4B 1K3 Canada 5 Tel: 905-762-1228 | Fax: 905-763-1737 | E-mail: info@laipac.com | http://www.laipac.com 1.1 About Your Device The wireless device described for using GSM 850/900/1800/1900 networks. Contact your service provider for more information about which GSM frequency your service provider is using. When using the features in this device, obey all laws, respect privacy, and the legitimate rights of others. is approved this guide in 1.2 Network Services In order to use the S-911 Lola, you must have GSM/GPRS service from a wireless service provider and subscribe with LocationNow. Many of the features in this device depend on the features of the GSM provider to function. These network services may not be available with all providers. It means you may have to make specific arrangements with your service provider before you can utilize the network services. Your service provider may need to give you additional instructions for their use and explain what charges will apply. Some networks may have limitations that affect how you can use network services in your area. 1.3 Care and Maintenance Your device is a product of superior design and craftsmanship. The suggestions below will help you protect your warranty coverage. Keep the device dry. Precipitation, humidity, and all types of liquids or moisture can contain minerals that will corrode the electronic circuits. Do not store the device in hot and high humidity areas. High temperature and humidity can shorten the life of electronic devices, damage batteries, and warp or melt certain plastics. Do not attempt to open the device other than as authorized technician by Laipac. Do not drop, knock, or shake the device on purpose. It will trigger the tamper alert to the monitoring centre if internal motion sensor is enabled. Do not use harsh chemicals, cleaning solvents, or strong detergents to clean the device
- Chapter 2 Introduction 2.1 Welcome Congratulations on purchasing the S-911 Lola!
The S-911 Loa is a real-time personal tracking device which operates over GSM/GPRS networks and utilizes a built-in high sensitivity GPS receiver. Your Lola contains A new generation of high-sensitivity GPS receiver A GPS Data Logger which can plot 128 waypoints and a built in Smart Logger that can plot over 10,000 waypoints A real-time emergency assistance button 2-way voice communication over GSM Real-time location reporting over SMS/GPRS Speed limit alerting, mileage reporting, G-Sensor/shock alerting, and versatile Geo-
Fence alerting are all standard And much more The Lola is an all-in-one compact and unique personal safety device. The following guide will help you know about Lola and quickly instruct you on usage and operation of this device. 2.2 Main Features Available for GSM/GPRS in 850/1900 900/1800 MHz Complies with FCC, CE, and PTCRB (Under certification process) Compact and robust design for portable usage GPS, GSM/GPRS & Battery/Status Indicator LEDs Internal Li-Ion Polymer rechargeable battery Built in new generation of High-Sensitivity GPS receiver CGEE AGPS, get ephemeris data from satelite locally, is available SGEE AGPS, get ephemeris data from server, is able to be provided (optional) 1x SOS button for emergency assistance, pick up and hang up the incoming call 1 x Power button for power on/off device Data logger with dynamic distance & time settings for recording up to 128 positions Intelligent logger, Smart Logger, designed to store dynamic waypoint information in the event of there being no GPRS with the ability to transmit the information once GPRS recovers GSM/SMS and GPRS real-time position reporting by time interval or distance traveled The ability to set parameters either remotely over the air or locally through USB port Distance accumulator built in for mileage reporting Versatile multi-Geo-fence, up to 20, with alert selection of Geo-fence in, out as well both in & out Geo-fence alert email with address information Over-speed warning report G-Sensor/shock alert report Power Saving mode for even more extended battery life
- Chapter 3 -
Specification 3.1 Electrical & Environmental Specs Item Li-Ion polymer Battery Voltage Current Consumption while connecting Min Typical Max 4.2 3.0 50 210 3.7 140 Current Consumption in operation 38 44 57 Units V mA mA mode (Idling) Current consumption in operation 130 135 140 mA mode (Reporting) Current Consumption in Power off Mode Peak Current (< 100mS) Ambient operating temperature Storage temperature
-40
-40 0.7
uA
1500 85 85 mA C C Note: Current consumption is subject to change in areas with lower signals strength vs higher strength. Table 3.1 3.2 GPS Engine Specification Item Channels RF Frequency Position update rate Position accuracy Velocity accuracy Time accuracy Cold start acquisition time Warm start acquisition time Hot start acquisition time Maximum velocity tracked Maximum altitude tracked Tracking Sensitivity Navigation Sensitivity Value 48 1575.42 1
< 10 0.1 1 35 35
< 1 514 18,288
-163
-160 Units Channels MHz Hz Meters m/s uS Seconds Seconds Seconds m/s Meters dBm dBm Table 3.2 3.3 GSM Module Specification Quad-band GSM/GPRS component (850/900/1800/1900 MHz) Class 4 (2W @ 850 / 900 MHz) Class 1 (1W @ 1800 / 1900 MHz) R&TTE, GCF, FCC, PTCRB, IC Embedded TCP/IP stack. GPRS Class 10
- Chapter 4 -
SIM Card and Its Installation This chapter describes the request for SIM card and the installation procedure of SIM card used for the S-911 Lola. 4.1 Requirement for SIM Card In order to use the Lola, you should have a valid SIM (Subscribe Identity Module) card provided by your local GSM/GPRS service provider. This card can be both of the GPRS DATA and voice/SMS functions enabled, or only one of them enabled. If only voice/SMS function is enabled, your Lola is not able to access the Location Based Service platform, such as, LocationNow.com, which requesting a SIM card with DATA function enabled. 4.2 Installation of SIM Card A special tool, SIM Card Key, is asked for the installation procedure of SIM card. Follow steps below, user can open SIM Card tray and install SIM Card into Lola.
- Chapter 5 Configuration, Upgrading and Utility Laipac Technology Inc. 5.1 Introduction to Laipac Suite As a personal tracking device, if the Lola wants to work with certain Tracking Service providers platform, such as, www.LocationNow.com from Laipac Technology Inc., it should properly be configured by using a software tool. Also, to support application firmware upgrading for the Lola, it needs a software tool to download that new firmware. LocationNow Suite is the utility software to meet the requirements above. 5.2 Usage of Laipac Suite Another document, S911 Lola Utility Operation Manual, introduces the detail procedures below How to install this utility and its USB driver How to configure Lola How to upgrade Lolas application firmware 20 Mural Street, Unit 5, Richmond Hill Ontario L4B 1K3 Canada 16 Tel: 905-762-1228 | Fax: 905-763-1737 | E-mail: info@laipac.com | http://www.laipac.com Laipac Technology Inc.
- Chapter 6 Operation Instruction 20 Mural Street, Unit 5, Richmond Hill Ontario L4B 1K3 Canada 17 Tel: 905-762-1228 | Fax: 905-763-1737 | E-mail: info@laipac.com | http://www.laipac.com Laipac Technology Inc. This chapter describes the S-911 Lolas typical operation procedures, which is provided by the demo application firmware V1.02, the corresponding hardware version is V2.0. 6.1 Knowing about your Lola Fig. 6.1 shows the locations and names of the major physical features with this product Fig. 6.1 20 Mural Street, Unit 5, Richmond Hill Ontario L4B 1K3 Canada 18 Tel: 905-762-1228 | Fax: 905-763-1737 | E-mail: info@laipac.com | http://www.laipac.com 6.2 Function Button and Its Related Operation There are 2 function buttons on Lola, user can find their positions in Fig. 6.1 above. Power Button:
It is being used for turning on or off the S911 Lola unit. Turn On the unit:
Press this button over 3 seconds, user should feel the vibration form the built-in vibrator. Also, all 3 LED indicators, GPS indicator LED, GSM indicator LED and SOS button backlight LED, are going to flash Turn Off the unit:
Press this button for over 3 seconds, user should feel the vibration from the built-in vibrator. SOS Button:
It is being used to send SOS alert message, pick up/hand up phone call as well as checking Lolas working status Send SOS alert:
Press this button for over 3 seconds, if user can see the flashing generated by SOS button back light LED, it means this SOS request has been accepted and unit will activate its SOS alert action sequence. Pick up phone:
When unit has incoming phone call, user can press this button to pick up the phone. Hand up phone:
During or after the phone call, user can press this button to hand up the phone Checking status:
Laipac Technology Inc. Press this button, user can hear beeping. Also, the LED indicators can tell user the working status of those major function parts inside Lola, such as GPS and GSM. 6.3 LED indicators and Lolas working status There are 3 color LED indicators on Lola. They are as below GPS LED (White color) GSM LED (White or Red color) SOS Button Backlight LED (White color) Table 6.3 describes how to identify the Lolas working status by observing the behavior of those 3 LED indicators. 20 Mural Street, Unit 5, Richmond Hill Ontario L4B 1K3 Canada 20 Tel: 905-762-1228 | Fax: 905-763-1737 | E-mail: info@laipac.com | http://www.laipac.com Item GPS LED GSM LED 1 2 3 4 5 6 7 White LED flashing White LED Fast flashing White LED flashing White LED Fast flashing White LED is on White LED Fast flashing White LED is on White LED is on White LED flashes every 5s Red LED flashes every 5s 8* White LED fast flashing White LED fast flashing 9* White LED is on White LED Fast flashing 8* White LED is on White LED is on 9* White LED White LED is on SOS Back light LED Vibrator LED flashing work flashing LED turn off 10 Operation and units working status Unit is under charging and battery volt. is too low to activate unit 1. Battery volt. is high enough to activate the unit automatically, or 2. Press Power button to turn on the unit Unit is in normal working condition, or so 1. GPS is not fixed 2. GSM is not able to register on GSM network Unit is in normal working condition, and 1. GPS is fixed 2. GSM is not able to register on GSM network Unit is in normal working condition, and 1. GPS is fixed 2. GSM is registered on GSM network Unit is in normal working condition, if there is no button operation over 30s , unit will enter into user interface power saving mode 1. Unit is under user interface power saving mode 2. Battery volt. is low 1. Unit is under user interface power saving mode 2. Press SOS button to check units status, and the result is a. units position is not fixed yet b. Unit has not registered on GSM 1. Unit is under user interface power saving mode 2. Press SOS button to check units status, and the result is c. units position is fixed d. Unit has not registered on GSM 1. Unit is under user interface power saving mode 2. Press SOS button to check units status, and the result is e. units position is fixed f. Unit has registered on GSM network Press SOS button to check units status g. units position is not fixed h. Unit has registered on GSM net work LED turn off LED turn off work Press Power button to turn off the unit Table 6.3
*Note: 1. For Item 8 to 9, if it is also with GSM red LED flashing, it means that units battery is low and it can last a couple of hours. 2. If user also hears the beep that means the battery voltage is very low and unit will turn off itself actively very soon.