TiWi-uB2 / uBleu2 Module DATASHEET TiWi-uB2 / uBleu2 Bluetooth Module FEATURES DESCRIPTION LSR would like to announce a low-cost and low-
power consumption module which has all of the Bluetooth functionalities. The highly integrated TiWi-uB2 module makes the use of Bluetooth headsets and other applications possible. The TiWi-uB2 module fully supports the dual mode Bluetooth and BLE operation, and the output power can support class 1.5. The SIP module provides UART interface / audio PCM interface for Bluetooth. The SIP module is specifically developed for Smart phones and Portable devices. Need to get to market quickly? Not an expert in Bluetooth? Need a custom antenna? Do you need help with your host board? LS Research Design Services will be happy to develop custom hardware or software, or help integrate the design. Contact us at sales@lsr.com or call us at 262-375-4400. Built in CC2564 single-chip Bluetooth fully supports BT 2.1 + EDR, BLE 4.0. RF Output Power: +10 dBm (Class 1.5) RF Receive Sensitivity: -94 dBm Miniature Size: 7 mm x 7 mm x 1.5 mm Operating Voltage: 2.2V to 4.8V Operating temperature: -30 to +85o C Worldwide acceptance: FCC (USA), IC
(Canada), and CE (Europe) RoHS compliant Supports maximum Bluetooth data rates over HCI UART interface. Supports multiple Bluetooth profiles with enhanced QoS, both mono and stereo, assisted A2DP APPLICATIONS Medical (ex Heart Rate Monitor, Blood Pressure Sensor, Blood Glucose Meter) Industrial Sensors Thermometer Flood Alarm Heating Control Automatic Key Control Toys Entertainment Devices Mobile Accessories All Bluetooth Wireless Applications ORDERING INFORMATION Order Number Description 450-0104 TiWi-uB2 Module (Tray) 450-0104R TiWi-uB2 Module (Tape & Reel) 450-0105 TiWi-uB2 EM Board Table 1 Orderable Model Numbers The information in this document is subject to change without notice. TiWi-uB2 uBleu2 Datasheet Copyright 2012 LS Research, LLC Page 1 of 25 MODULE ACCESSORIES Order Number Description TiWi-uB2 / uBleu2 Module DATASHEET 001-0001 2.4 GHz Dipole Antenna with Reverse Polarity SMA Connector 080-0001 U.FL to Reverse Polarity SMA Bulkhead Cable 105mm Table 2 Module Accessories The information in this document is subject to change without notice. TiWi-uB2 uBleu2 Datasheet Copyright 2012 LS Research, LLC Page 2 of 25 TiWi-uB2 / uBleu2 Module DATASHEET TABLE OF CONTENTS FEATURES .......................................................................................................................... 1 APPLICATIONS ................................................................................................................... 1 DESCRIPTION ..................................................................................................................... 1 ORDERING INFORMATION ................................................................................................ 1 MODULE ACCESSORIES ................................................................................................... 2 FOOTPRINT AND PIN DEFINITIONS.................................................................................. 5 PIN DESCRIPTIONS ............................................................................................................ 6 ELECTRICAL SPECIFICATIONS ........................................................................................ 7 Absolute Maximum Ratings ....................................................................................................................... 7 Recommended Operating Conditions ...................................................................................................... 7 General Characteristics .............................................................................................................................. 8 Bluetooth RF Characteristics .................................................................................................................. 10 BLUETOOTH POWER-UP/ DOWN SEQUENCE .............................................................. 11 nSHUTD Requirements ............................................................................................................................. 11 SLOW CLOCK (32 KHZ) SOURCE REQUIREMENTS ..................................................... 12 BLUETOOTH HCI UART ................................................................................................... 13 BLUETOOTH AUDIO CODEC/PCM .................................................................................. 14 SOLDERING RECOMMENDATIONS ................................................................................ 15 Recommended Reflow Profile for Lead Free Solder ............................................................................. 15 CLEANING ......................................................................................................................... 16 OPTICAL INSPECTION ..................................................................................................... 16 REWORK ........................................................................................................................... 16 SHIPPING, HANDLING, AND STORAGE ......................................................................... 16 Shipping ..................................................................................................................................................... 16 Handling ..................................................................................................................................................... 16 Moisture Sensitivity Level (MSL) ............................................................................................................. 16 Storage ....................................................................................................................................................... 16 The information in this document is subject to change without notice. TiWi-uB2 uBleu2 Datasheet Copyright 2012 LS Research, LLC Page 3 of 25 TiWi-uB2 / uBleu2 Module DATASHEET Repeating Reflow Soldering .................................................................................................................... 17 AGENCY CERTIFICATIONS ............................................................................................. 18 AGENCY STATEMENTS ................................................................................................... 18 Federal Communication Commission Interference Statement ............................................................ 18 Industry Canada Statements.................................................................................................................... 19 OEM RESPONSIBILITIES TO COMPLY WITH FCC AND INDUSTRY CANADA REGULATIONS ....................................................................................................... 20 OEM LABELING REQUIREMENTS FOR END-PRODUCT .............................................. 21 OEM END PRODUCT USER MANUAL STATEMENTS.................................................... 22 MECHANICAL DATA......................................................................................................... 23 CONTACTING LS RESEARCH ......................................................................................... 25 The information in this document is subject to change without notice. TiWi-uB2 uBleu2 Datasheet Copyright 2012 LS Research, LLC Page 4 of 25 FOOTPRINT AND PIN DEFINITIONS TiWi-uB2 / uBleu2 Module DATASHEET Figure 1 TiWi-uB2 Module Schematic View Figure 2 TiWi-uB2 Module Footprint View The information in this document is subject to change without notice. TiWi-uB2 uBleu2 Datasheet Copyright 2012 LS Research, LLC Page 5 of 25 TiWi-uB2 / uBleu2 Module DATASHEET PIN DESCRIPTIONS Module Pin Name I/O Type Description 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 HCI_CTS HCI_TX HCI_RX HCI_RTS GND GND GND I O I O HCI UART CLEAR-TO-SEND HCI UART DATA TRANSMIT HCI UART DATA RECEIVE HCI UART REQUEST-TO-SEND GND GND GND GROUND GROUND GROUND SLOW_CLK_IN I 32.768 kHz CLOCK IN GND NC1 NC2 VBAT GND BT_ANT GND nSHUTD GND VDD_IO AUD_IN AUD_OUT AUD_CLK AUD_FSYNC NC3 TX_DBG GND GROUND O O PI NO CONNECT 1 (DO NOT CONNECT) NO CONNECT 2 (DO NOT CONNECT) POWER TO MODULE (2.2V - 4.8V) GND GROUND RF ANTENNA, 50 OHMS GND GROUND I SHUTDOWN INPUT (ACTIVE LOW) GND GROUND PI I O IO IO O O I/O POWER SUPPLY (1.8V NOMINAL) PCM DATA INPUT (IF NOT USED, DO NOT CONNECT) PCM DATA OUTPUT (IF NOT USED, DO NOT CONNECT) PCM CLOCK (IF NOT USED, DO NOT CONNECT) PCM FRAME SYNCH (IF NOT USED, DO NOT CONNECT) NO CONNECT 3 (DO NOT CONNECT) LOGGER OUTPUT 25-33 GND GND GROUND PI = Power Input I = Input O = Output IO = Bi-directional Input Output Port RF = Bi-directional RF Port GND=Ground Table 3 TiWi-uB2 Pin Descriptions The information in this document is subject to change without notice. TiWi-uB2 uBleu2 Datasheet Copyright 2012 LS Research, LLC Page 6 of 25 TiWi-uB2 / uBleu2 Module DATASHEET ELECTRICAL SPECIFICATIONS Absolute Maximum Ratings Symbol Description VBAT Input supply Voltage Min
-0.5 VDD_IO Digital Bluetooth I/O Voltage
-0.5 Table 4 Absolute Maximum Ratings1 Max Unit 5.5 2.145 V V Recommended Operating Conditions Test conditions: Ambient Temp = 25C Symbol VBAT VDD_IO Min 2.2 1.62 Typ 3.3 1.8 Max 4.8 1.92 Unit V V Table 5 Recommended Operating Conditions 1 Under no circumstances should exceeding the ratings specified in the Absolute Maximum Ratings section be allowed. Stressing the module beyond these limits may result permanent damage to the module that is not covered by the warranty. The information in this document is subject to change without notice. TiWi-uB2 uBleu2 Datasheet Copyright 2012 LS Research, LLC Page 7 of 25 TiWi-uB2 / uBleu2 Module DATASHEET General Characteristics Characteristic Description Model Name TiWi-uB2 Product Description Bluetooth Wireless Module Dimension BT Interface 7.0 mm x 7.0 mm x 1.5 mm (W*L*T) HCI UART, Audio PCM Operating temperature
-30C to 85C Storage temperature
-40C to 85C Humidity Weight Operating Humidity 10% to 95% Non-Condensing Storage Humidity 5% to 95% Non-Condensing 0.18 g +/- 0.01g Table 6 General Characteristics Current Consumption for Different Bluetooth BR/EDR Scenarios Conditions: VBAT = 3.6 V, VDDIO = 1.8V 25C, 26-MHz fast clock, nominal unit, 4 dBm output power Mode Description Master/Slave Average Current Unit Idle current (ARM off) SCO link HV3 eSCO link EV3 64 kbps, no retransmission eSCO link 2-EV3 64 kbps, no retransmission GFSK full throughput: TX = DH1, RX = DH5 Master/slave Master/slave Master/slave Master/slave Master/slave EDR full throughput: TX = 2-DH1, RX = 2-DH5 Master/slave EDR full throughput: TX = 3-DH1, RX = 3-DH5 Master/slave 2.5 12 11.5 8.3 38.5 39.2 39.2 Sniff, one attempt, 1.28 s Master/slave 76/100 Page or inquiry scan 1.28 s, 11.25 ms Master/slave Page (1.28 s) and inquiry (2.56 s) scans, 11.25 ms Master/slave Low power scan, 1.28-s interval, quiet environment Master/slave 300 430 135 Table 7 Bluetooth Power Consumption mA mA mA mA mA mA mA A A A A The information in this document is subject to change without notice. TiWi-uB2 uBleu2 Datasheet Copyright 2012 LS Research, LLC Page 8 of 25 TiWi-uB2 / uBleu2 Module DATASHEET Current Consumption for Different Bluetooth LE Scenarios Conditions: VBAT = 3.6 V, VDDIO = 1.8V, 25C, 26-MHz fast clock, nominal unit, 10 dBm output power Mode Description Average Current Unit Advertising, non-
connectable Advertising, discoverable Scanning Advertising in all 3 channels 1.28msec advertising interval 15Bytes advertise data Advertising in all 3 channels 1.28msec advertising interval 15Bytes advertise data Listening to a single frequency per window 1.28msec scan interval 11.25msec scan window 500msec connection interval Connected (master role) 0msec Slave connection latency Empty Tx/Rx LL packets Table 8 Bluetooth Power Consumption Power Consumption Bluetooth Conditions: VBAT = 3.3V, VDDIO = 1.8V, Ambient Temp = 25C 104 121 302 169 A A A A Packet type DM1 DH1 DM3 DH3 DM5 DH5 Deep Sleep Mode Constant RX BER Mode Typ 47.1 30.2 21.3 17.4 15.6 13.0 0.033 44.5 38.8 Max Unit mA mA mA mA mA mA mA mA mA Table 9 Bluetooth VBAT Power Consumption Packet type DM1 DH1 DM3 DH3 DM5 DH5 Deep Sleep mode Constant RX BER Mode Typ 0.069 0.069 0.069 0.069 0.069 0.069 0.032 0.069 0.069 Max Unit mA mA mA mA mA mA mA mA mA Table 10 Bluetooth VDDIO Power Consumption The information in this document is subject to change without notice. TiWi-uB2 uBleu2 Datasheet Copyright 2012 LS Research, LLC Page 9 of 25 TiWi-uB2 / uBleu2 Module DATASHEET Bluetooth RF Characteristics General Specifications Feature Description Bluetooth Standard Bluetooth 4.0 (with EDR) Host Interface HCI UART, PCM Antenna Reference Small antennas with 0~2 dBi peak gain Frequency Band 2.402 GHz ~ 2.480 GHz Number of Channels 79 channels Modulation FHSS, GFSK, DPSK, DQPSK Table 11 Bluetooth General Specifications RF Characteristics Test Conditions : VBAT = 3.3V, VDDIO = 1.8V Characteristic Condition
-30C Typ 25C Typ 85C Typ BT Spec Unit Class 1.5 dF1 avg dF2 max dF2avg / dF1avg RMS DEVM 99% DEVM Peak DEVM GFSK at BER = 0.1%
/4-DQPSK at BER = 0.01%
8DPSK at BER = 0.01%
GFSK at BER = 0.1%
/4-DQPSK at BER = 0.1%
8DPSK at BER = 0.1%
9.5 158 138 90 5 10 13
-95
-93
-86
-5
-10
-10 10 158 137 90 5 10 13
-94
-92
-85
-5
-10
-10 10.8 158 136 dBm 140~ 175 KHz
>115 KHz 90 5 10 13
-93
-91
-84
-5
-10
-10 80 13 20 25
-70
-70
-70
-20
-20
-20
dBm dBm dBm dBm dBm dBm Table 12 Bluetooth RF Characteristics Output Power Modulation GFSK Modulation EDR at 8DPSK Sensitivity at Dirty Tx On Maximum Input Level The information in this document is subject to change without notice. TiWi-uB2 uBleu2 Datasheet Copyright 2012 LS Research, LLC Page 10 of 25 BLUETOOTH POWER-UP/ DOWN SEQUENCE TiWi-uB2 / uBleu2 Module DATASHEET Figure 3 Bluetooth Power-Up/Down Sequence nSHUTD Requirements Parameter Symbol Min Max Unit Operation mode level (1) Shutdown mode level (1) Minimum time for nSHUT_DOWN low to reset the device Rise/fall times VIH VIL Tr/Tf 1.42 1.98 V V 0.4 20 us 0 5
(1) Internal pull-down retains shutdown mode when no external signal is applied to this pin. Table 13 nSHUTD Requirements The information in this document is subject to change without notice. TiWi-uB2 uBleu2 Datasheet Copyright 2012 LS Research, LLC Page 11 of 25 TiWi-uB2 / uBleu2 Module DATASHEET SLOW CLOCK (32 KHZ) SOURCE REQUIREMENTS External Slow Clock signal characteristics Characteristic Condition Sym Min Typ Max Unit Input slow clock frequency Input slow clock accuracy
(Initial + temp + aging) Input transition time tr/tf - 10% to 90%
Frequency input duty cycle Phase noise Jitter Slow clock input voltage limits At 1 kHz Integrated over 300 to 15000 Hz Square wave, DC coupled Input impedance Input capacitance VIH VIL 32768 Hz
-250 tr/tf 15 0.65 x VDD_IO 0 1 50 250 ppm 100 85 ns
-125 dBc/Hz 1 Hz VDD_IO V peak 0.35 x VDD_IO V peak 5 M pF Table 14 32 kHz Clock Requirements The information in this document is subject to change without notice. TiWi-uB2 uBleu2 Datasheet Copyright 2012 LS Research, LLC Page 12 of 25 BLUETOOTH HCI UART TiWi-uB2 / uBleu2 Module DATASHEET Figure 4 Bluetooth HCI UART Timing Symbol Characteristic Condition Min Typ Max Unit t3 t4 t6 t1 t2 Baud rate Baud rate accuracy CTS low to TX_DATA on CTS high to TX_DATA off Hardware flow control CTS high pulse width RTS low to RX_DATA on RTS high to RX_DATA off Interrupt set to FIFI Table 15 Bluetooth HCI UART Timing 37.5
-2.5 0 1 0 2 2 4000 kbps 1.5 1
us byte Bit us 16 byte The information in this document is subject to change without notice. TiWi-uB2 uBleu2 Datasheet Copyright 2012 LS Research, LLC Page 13 of 25 BLUETOOTH AUDIO CODEC/PCM TiWi-uB2 / uBleu2 Module DATASHEET Figure 5 Bluetooth PCM Timing PCM Master Symbol Parameter Condition Min Max Unit Tclk TW tis tih top top Cycle time High or low pulse width AUD_IN setup time AUD_IN hold time AUD_OUT propagation time 40pF load FSYNC_OUT propagation time 40pF load 166.67 (6 MHz) 15625 (64 kHz) 50% of Tclk min 25 0 0 0 10 10 ns ns ns ns ns ns Table 16 Bluetooth PCM Master Timing PCM Slave Symbol Parameter Condition Min Max Unit Tclk TW tis tih tis tih top Cycle time High or low pulse width AUD_IN setup time AUD_IN hold time AUD_FSYNC setup time AUD_FSYNC hold time AUD_OUT propagation time 40pF load 62.5 (16 MHz) 40% of Tclk 8 0 8 0 0 21 ns ns ns ns ns ns ns Table 17 Bluetooth PCM Slave Timing The information in this document is subject to change without notice. TiWi-uB2 uBleu2 Datasheet Copyright 2012 LS Research, LLC Page 14 of 25 TiWi-uB2 / uBleu2 Module DATASHEET SOLDERING RECOMMENDATIONS Recommended Reflow Profile for Lead Free Solder Figure 6 Recommended Soldering Profile Note: The quality of solder joints on the surface mount pads where they contact the host board should meet the appropriate IPC Specification. See IPC-A-610-D Acceptability of Electronic Assemblies, section 8.2.1 Bottom Only Terminations. The information in this document is subject to change without notice. TiWi-uB2 uBleu2 Datasheet Copyright 2012 LS Research, LLC Page 15 of 25 CLEANING SHIPPING, HANDLING, AND STORAGE TiWi-uB2 / uBleu2 Module DATASHEET In general, cleaning the populated modules is strongly discouraged. Residuals under the module cannot be easily removed with any cleaning process. Cleaning with water can lead to capillary effects where water is absorbed into the gap between the host board and the module. The combination of soldering flux residuals and encapsulated water could lead to short circuits between neighboring pads. Water could also damage any stickers or labels. Cleaning with alcohol or a similar organic solvent will likely flood soldering flux residuals into the RF shield, which is not accessible for post-washing inspection. The solvent could also damage any stickers or labels. Ultrasonic cleaning could damage the module permanently. OPTICAL INSPECTION After soldering the Module to the host board, consider optical inspection to check the following:
Proper alignment and centering of the module over the pads. Proper solder joints on all pads. Excessive solder or contacts to neighboring pads, or vias. REWORK The module can be unsoldered from the host board if the Moisture Sensitivity Level (MSL) requirements are met as described in this datasheet. Never attempt a rework on the module itself, e.g. replacing individual components. Such actions will terminate warranty coverage. Shipping Bulk orders of the TiWi-uB2 modules are delivered in trays of 416 (13 x 32) or reels of 2,000. Handling The TiWi-uB2 modules contain a highly sensitive electronic circuitry. Handling without proper ESD protection may damage the module permanently. Moisture Sensitivity Level (MSL) Per J-STD-020, devices rated as MSL 4 and not stored in a sealed bag with desiccant pack should be baked prior to use. After opening packaging, devices that will be subjected to reflow must be mounted within 72 hours of factory conditions (<30C and 60%
RH) or stored at <10% RH. Bake devices for 48 hours at 125C. Storage Please use this product within 6 months after receipt. Any product used after 6 months of receipt needs to have solderability confirmed before use. The product shall be stored without opening the packing under the ambient temperature from 5 to 35deg.C and humidity from 20 to 70%RH.
(Packing materials, in particular, may be deformed at the temperatures above this range.) Do not store in salty air or in an environment with a high concentration of corrosive gas, such as Cl2, H2S, NH3, SO2, or NOX. Do not store in direct sunlight. The product should not be subject to excessive mechanical shock. The information in this document is subject to change without notice. TiWi-uB2 uBleu2 Datasheet Copyright 2012 LS Research, LLC Page 16 of 25 TiWi-uB2 / uBleu2 Module DATASHEET Repeating Reflow Soldering Only a single reflow soldering process is encouraged for host boards. The information in this document is subject to change without notice. TiWi-uB2 uBleu2 Datasheet Copyright 2012 LS Research, LLC Page 17 of 25 TiWi-uB2 / uBleu2 Module DATASHEET AGENCY CERTIFICATIONS FCC ID: TFB-BT1, 15.247 IC ID: 5969A-BT1, RSS 210 CE: Compliant to standards EN 60950-1, EN 300 328, and EN 301 489 AGENCY STATEMENTS Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This portable transmitter with its antenna complies with FCC/IC RF exposure limits for general population / uncontrolled exposure. FCC CAUTION: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. The information in this document is subject to change without notice. TiWi-uB2 uBleu2 Datasheet Copyright 2012 LS Research, LLC Page 18 of 25 TiWi-uB2 / uBleu2 Module DATASHEET Industry Canada Statements This device complies with Industry Canada License-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that permitted for successful communication. This device has been designed to operate with the antenna(s) listed below, and having a maximum gain of 2.0 dBi (LSR Dipole) and 1.3dBi (Johanson Chip). Antennas not included in this list or having a gain greater than 2.0 dBi and 1.3dBi are strictly prohibited for use with this device. The required antenna impedance is 50 ohms. List of all Antennas Acceptable for use with the Transmitter 1) LS Research 001-0001 center-fed dipole antenna and LS Research 080-0001 U.FL to Reverse Polarity SMA connector cable. 2) Johanson 2450AT43B100 chip antenna. Cet appareil est conforme aux normes d'Industrie Canada exempts de licence RSS (s). L'opration est soumise aux deux conditions suivantes: (1) cet appareil ne peut pas provoquer d'interfrences et (2) cet appareil doit accepter toute interfrence, y compris les interfrences qui peuvent causer un mauvais fonctionnement de l'appareil. Pour rduire le risque d'interfrence aux autres utilisateurs, le type d'antenne et son gain doiventtre choisis de manire que la puissance isotrope rayonne quivalente (PIRE) ne dpasse pascelle permise pour une communication russie. Cet appareil a t conu pour fonctionner avec l'antenne (s) ci-dessous, et ayant un gain maximum de 2,0 dBi (LSR diple) et1.3dBi (Chip Johanson). Antennes pas inclus danscette liste ou d'avoir un gain suprieur 2,0 dBi et-1.3dBi sont strictement interdites pour l'utilisation avec cet appareil. L'impdance d'antenne requise est de 50 ohms. Liste de toutes les antennes acceptables pour une utilisation avec l'metteur 1) LS Research 001-0001 aliment par le centre antenne diple et LS Research 080-0001 U.FL d'inversion de polarit du cble connecteur SMA. 2) Antenne Johanson puce 2450AT43B100. The information in this document is subject to change without notice. TiWi-uB2 uBleu2 Datasheet Copyright 2012 LS Research, LLC Page 19 of 25 TiWi-uB2 / uBleu2 Module DATASHEET OEM RESPONSIBILITIES TO COMPLY WITH FCC AND INDUSTRY CANADA REGULATIONS The TiWi-uB2 Module has been certified for integration into products only by OEM integrators under the following conditions:
The antennas for this transmitter must not be co-located with any other transmitters except in accordance with FCC and Industry Canda multi-transmitter procedures. Co-location means having a separation distance of less than 20 cm between transmitting antennas. As long as the two conditions above are met, further transmitter testing will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed (for example, digital device emissions, PC peripheral requirements, etc.). IMPORTANT NOTE: In the event that these conditions cannot be met (for certain configurations or co-location with another transmitter), then the FCC and Industry Canada authorizations are no longer considered valid and the FCC ID and IC Certification Number cannot be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC and Industry Canada authorization. Le module de TiWi-uB2 a t certifi pour l'intgration dans des produits uniquement par des intgrateurs OEM dans les conditions suivantes:
Les antennes pour ce transmetteur ne doit pas tre co-localiss avec les autres metteurs sauf en conformit avec la FCC et Industrie Canada multi-metteur procdures. Co-localisation des moyens ayant une distance de sparation infrieure 20 cm entre les antennes d'mission. Tant que les deux conditions prcites sont runies, les tests de transmetteurs supplmentaires ne seront pas tenus. Toutefois, l'intgrateur OEM est toujours responsable de tester leur produit final pour toutes les exigences de conformit supplmentaires requis avec ce module install (par exemple, les missions appareil numrique, les exigences de priphriques PC, etc.) NOTE IMPORTANTE: Dans le cas o ces conditions ne peuvent tre satisfaites (pour certaines configurations ou de co-implantation avec un autre metteur), puis la FCC et Industrie autorisations Canada ne sont plus considrs comme valides et l'ID de la FCC et IC numro de certification ne peut pas tre utilis sur la produit final. Dans ces circonstances, l'intgrateur OEM sera charg de rvaluer le produit final (y compris l'metteur) et l'obtention d'un distincte de la FCC et Industrie Canada l'autorisation. The information in this document is subject to change without notice. TiWi-uB2 uBleu2 Datasheet Copyright 2012 LS Research, LLC Page 20 of 25 TiWi-uB2 / uBleu2 Module DATASHEET OEM LABELING REQUIREMENTS FOR END-PRODUCT The TiWi-uB2 module is labeled with its own FCC ID and IC Certification Number. The FCC ID and IC certification numbers are not visible when the module is installed inside another device, as such the end device into which the module is installed must display a label referring to the enclosed module. The final end product must be labeled in a visible area with the following:
Contains Transmitter Module FCC ID: TFB-BT1 Contains Transmitter Module IC: 5969A-BT1 or Contains FCC ID: TFB-BT1 Contains IC: 5969A-BT1 The OEM of the TiWi-uB2 Module must only use the approved antenna(s) listed above, which have been certified with this module. Le module de TiWi-uB2 est tiquet avec son propre ID de la FCC et IC numro de certification. L'ID de la FCC et IC numros de certification ne sont pas visibles lorsque le module est install l'intrieur d'un autre appareil, comme par exemple le terminal dans lequel le module est install doit afficher une etiquette faisant rfrence au module ci-joint. Le produit final doit tre tiquet dans un endroit visible par le suivant:
Contient Module metteur FCC ID: TFB-BT1"
Contient Module metteur IC: 5969A-BT1"
ou Contient FCC ID: TFB-BT1"
Contient IC: 5969A-BT1"
Les OEM du module TiWi-uB2 ne doit utiliser l'antenne approuve (s) ci-dessus, qui ont t certifis avec ce module. The information in this document is subject to change without notice. TiWi-uB2 uBleu2 Datasheet Copyright 2012 LS Research, LLC Page 21 of 25 TiWi-uB2 / uBleu2 Module DATASHEET OEM END PRODUCT USER MANUAL STATEMENTS The OEM integrator should not provide information to the end user regarding how to install or remove this RF module or change RF related parameters in the user manual of the end product. Other user manual statements may apply. L'intgrateur OEM ne devraient pas fournir des informations l'utilisateur final sur la faon d'installer ou de supprimer ce module RF ou modifier les paramtres lis RF dans le manuel utilisateur du produit final. Autres dclarations manuel de l'utilisateur peuvent s'appliquer. The information in this document is subject to change without notice. TiWi-uB2 uBleu2 Datasheet Copyright 2012 LS Research, LLC Page 22 of 25 MECHANICAL DATA TiWi-uB2 / uBleu2 Module DATASHEET Figure 7 Module Mechanical Dimensions The information in this document is subject to change without notice. TiWi-uB2 uBleu2 Datasheet Copyright 2012 LS Research, LLC Page 23 of 25 TiWi-uB2 / uBleu2 Module DATASHEET Figure 8 Soldering Footprint for Host Board and Module Placement The information in this document is subject to change without notice. TiWi-uB2 uBleu2 Datasheet Copyright 2012 LS Research, LLC Page 24 of 25 TiWi-uB2 / uBleu2 Module DATASHEET CONTACTING LS RESEARCH Headquarters Website Wiki LS Research, LLC W66 N220 Commerce Court Cedarburg, WI 53012-2636 USA Tel: 1(262) 375-4400 Fax: 1(262) 375-4248 www.lsr.com wiki.lsr.com Technical Support forum.lsr.com Sales Contact sales@lsr.com The information in this document is provided in connection with LS Research (hereafter referred to as LSR) products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of LSR products. EXCEPT AS SET FORTH IN LSRS TERMS AND CONDITIONS OF SALE LOCATED ON LSRS WEB SITE, LSR ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL LSR BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDENTAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF LSR HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. LSR makes no representations or warranties with respect to the accuracy or completeness of the contents of this document and reserves the right to make changes to specifications and product descriptions at any time without notice. LSR does not make any commitment to update the information contained herein. Unless specifically provided otherwise, LSR products are not suitable for, and shall not be used in, automotive applications. LSRs products are not intended, authorized, or warranted for use as components in applications intended to support or sustain life. The information in this document is subject to change without notice. TiWi-uB2 uBleu2 Datasheet Copyright 2012 LS Research, LLC Page 25 of 25