FCC ID: R68XPICO200 xPico 200 Series Wi-Fi IoT Gateway Module

 

SP500X SCAN-PRINTER Quick Start Guide Whats In The Box Battery SP500X SP500X*

*Includes fingerstrap. Wrist strap purchase separately. SP500X Parts Door Scanner USB Connect Charge Contacts Speaker Output LCD Battery User Label Keypad Wrist Clip holder Serial Number under handpad Fingerstrap Top Bottom For more information and cautions regarding product use, and to request additional product support, see the Knowledge Base at: www.handheldgroup.com/support-rugged-computers 01 POWERING ON THE SP500X SP500X 01. Install the battery by sliding it into the open slot on the SP500X. The curved side of the battery should align with the bottom of the SP500X. 02. Click the battery into place. The SP500X will power on. Tip: To power off the SP500X, remove the battery by squeezing the two latches towards one another, and pulling the battery out of the SP500X. The internal backup battery will keep the SP500X on for up to thirty (30) seconds. When the backup battery is exhausted, the SP500X will power off. Tip: To put the SP500X into Sleep Mode, press and hold the green power button for ten (10) seconds. 02 INSTALLING INK CARTRIDGE 01. Remove protective film from the ink cartridge. 03. Insert ink cartridge. The circular contacts on the cartridge should align with the contacts on the SP500X. Click ink cartridge into place, and close the SP500X door. 02. Open the SP500X door by depressing oval button. A. B. C. 03 USING KEYPAD AND LED FEEDBACK Keypad The LCD and keypad allow for navigation through the SP500X menus to retrieve data and alter settings. To reboot, press and hold the green power button for ten (10) seconds to put the SP500X into sleep mode. After releasing the button, press the same button again and the SP500X will reboot. LED Feedback There are two LEDs located at the back of the SP500X, on either side. The LED colors & behavior communicate various feedback. Initial Power Up, Ready to Print L+R - Solid Green Firmware Updating R - Solid Red SP500X Navigate Down Previous Power / Enter Firmware Downloading L+R - Blinking Green System Error*

L+R - Blinking Red

*low ink, failed print, door open, low battery 04 MOUNTING SP500X ON HAND The SP500X is equipped with a pre-installed finger strap. To correctly mount the SP500X on your hand, you will need to install a wrist strap. Note: There are two wrist strap sizes available for purchase seperately. Finger Strap Clip Wrist Strap Clip

*preinstalled on wrist strap 01. Install the wrist strap by snapping the triangle-shaped clip* onto the clip holder as shown, with the clips interior angle pointing upwards. 02. Secure the SP500X to the back of the hand using the wrist strap and finger strap. Adjust the straps to ensure a secure and comfortable fit. Two or three fingers may be used based on what is most comfortable to user. Tips:

Be careful to not over-tighten the straps. Remove all jewelry from your wrist and hand. Always maintain a relaxed wrist posture and low impact when printing. 05 CONFIGURING WIFI AND SERVER There are two methods for configuring the WiFi and server settings. The first requires the use of the PC App, SP500X Controller. Please refer to the SP500X Controller User Guide for this method. To perform the second method, a valid configuration barcode and close proximity to the appropriate access points are required. Configure Via Barcode 01. Using the SP500X keypad, navigate to the Server Configuration item:

Menu > SP500X Tasks > Server Configuration 02. Select Server Configuration. The SP500X scanner light will turn on. 03. Aim the scanner light at the configuration barcode. The light will turn off once the barcode is read. Upon connection to the access point, the LCD will display SUCCESS. 04. The SP500X will reboot to update the server and network settings. 05. The SP500X is now ready to use*

*Note: In some user environments you may also need to login before use as directed by your work environment. If so, please scan login barcode before continuing to use. 06 SCANNING AND PRINTING Scanning With SP500X mounted on hand, aim the scanner laser at the barcode you wish to scan. SP500X should be positioned 5-10 inches away from the desired barcode, at a twenty degree angle. When a valid barcode is scanned, the SP500X will sound an acceptance tone, indicating that the device is ready to print.

Note: If the scanner goes off, press the back button to turn the scanner back on. Warning: Do No Stare Into Beam, Class 2 Laser Product. Printing 20 Angle 5 - 10 Inches When printing, the SP500X front end Do not tilt the printer forward should remain level with the print or backwards while printing. surface until print is completed. 07 TROUBLESHOOTING AND MAINTENANCE SP500X Will Not Print or Print is Unclear Press back button to engage wiper/cleaning of cartridge. Wipe outside of door and door opening while keeping door closed. Ensure connection between unit and ink cartridge is free of debris. Ensure ink cartridge is properly installed. Ensure ink cartridge is not empty. Ensure WiFi and server settings are properly configured. Ensure logged in if required by your administration. SP500X Will Not Power On, or LCD Displays Low Battery Message Replace the battery with a fully charged battery. SP500X Will Not Connect to Server or WiFi Check Wifi Configuration / Settings to ensure SSID / PSK and Server information is correct. Check access points to ensure WiFi and server are properly configured and online. SP500X Scanner Will Not Turn On Press back button to turn on scanner. Replace battery. General Maintenance As needed, gently clean the unit using Texwipe material. Canned air may be used to remove debris. Wipe and clean any debris from the charger contacts daily. Wipe print head dimples as needed. Take care not to dent or rip gold flex cable. Ensure WiFi and server settings are properly configured. Foam hand pad is attached using velcro. To remove or replace, grasp pad and gently pull away from the SP500X. To remove or replace finger strap, use moderate pressure to release each clip by pressing or pulling clip towards the SP500X. To remove or replace wrist strap, use moderate pressure to release (or press in) each side, one at a time. See also section 04 for orientation details. FCC AND IC REGULATORY INFORMATION Please note the following regulatory information related to the wireless LAN device. Regulatory Notes and Statements Wireless LAN, Health and Authorization for use Radio frequency electromagnetic energy is emitted from Wireless LAN devices. The energy levels of these emissions, however, are far much less than the electromagnetic energy emissions from wireless devices such as mobile phones. Wireless LAN devices are safe for use by consumers because they operate within the guidelines found in radio frequency safety standards and recommendations. The use of Wireless LAN devices may be restricted in some situations or environments, such as:

On board an airplane, or In an explosive environment, or In situations where the interference risk to other devices or services is perceived or identified as harmful. In cases in which the policy regarding use of Wireless LAN devices in specific environments is not clear (e.g., airports, hospitals, chemical/oil/gas industrial plants, private buildings), obtain authorization to use these devices prior to operating the equipment. Regulatory Information/Disclaimers Installation and use of this Wireless LAN device must be in strict accordance with the instructions included in the user documentation provided with the product. Any changes or modifications made to this device that are not expressly approved by the manufacturer may void the users authority to operate the equipment. The manufacturer is not responsible for any radio or television interference caused by unauthorized modification of this device, or the substitution or attachment of connecting cables and equipment other than those specified by the manufacturer. It is the responsibility of the user to correct any interference caused by such unauthorized modification, substitution or attachment. The manufacturer and its authorized resellers or distributors will assume no liability for any damage or violation of government regulations arising from failure to comply with these guidelines. This device must not be co-located or operated in conjunction with any other antenna or transmitter. Federal Communications Commission and Industry Canada Compliance statement:

This device complies with Part 15 of FCC Rules and Industry Canada license exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause interference, and, (2) This device must accept any interference, including interference that may cause undesired operation of this device. Dclaration dIndustrie Canada Cet appareil est conforme la RSS concernant les appareils exempt s de licence par Industrie Canada. Son fonctionnement est soumis aux deux condition s suivantes : (1) cet appareil ne doit pas causer dinterfrence nuisib le; (2) cet appareil doit accepter toutes les interfrences reues, y compris celles pouvan t causer un mauvais fonctionnement de lappareil. FCC Interference Statement NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. FCC Radio Frequency Exposure statement The available scientific evidence does not show that any health problems are associated with using low power wireless devices. There is no proof, however, that these low power wireless devices are absolutely safe. Low power wireless devices emit low levels of radio frequency energy (RF) in the microwave range while being used. Whereas high levels of RF can produce health effects (by heating tissue), exposure to low-level RF that does not produce heating effects causes no known adverse health effects. Many studies of low-level RF exposure have not found any biological effects. Some studies have suggested that some biological effects might occur, but such findings have not been confirmed by additional research. The wireless LAN radio device has been tested and found to comply with FCC radiation exposure limits set forth for an uncontrolled equipment and meets the FCC radio frequency

(RF) Exposure Guidelines in Supplement C to OET65. The exposure standard for wireless devices employs a unit of measurement known as the Specific Absorption Rate, or SAR. The SAR limit set by the FCC is 1.6W/kg, and 1.6 W/kg by Industry Canada. This device is compliant with SAR for general population /uncontrolled exposure limits in ANSI/IEEE C95.1-1992 and Canada RSS 102, and had been tested in accordance with the measurement methods and procedures specified in OET Bulletin 65 Supplement C, and Canada RSS 102. This device has been tested, and meets the FCC, IC RF exposure guidelines when tested with the device operating conditions. Dclaration de la FCC/dIndustrie Canada sur lexposition aux radiofrquences La norme rgissant lexposition des appareils sans fil aux radiofrquences emploie une unit de mesure dnomme Taux dabsorption spcifique, ou TAS. La FCC et Industrie Canada ont dfini la mme limite de TAS : 1,6 W/kg. Cet appareil est conforme au TAS pour les limites dexposition gnrales de la population/non contrles dfinies par les rgles C95.1-1992 de lANSI/IEEE et RSS 102 dIndustrie Canada ; il a t test en conformit avec les mthodes et procdures de mesure spcifies dans le supplment C du bulletin 65 de lOET (Office dingnierie et de technologie) et la rgle RSS 102 dIndustrie Canada. Cet appareil a t test selon les directives de la FCC et dIC concernant lexposition aux radiofrquences et sest rvl conforme ces dernires lorsquil a t test en contact direct avec le corps. Export restrictions This product or software contains encryption code which may not be exported or transferred from the US or Canada without an approved US Department of Commerce export license. Modifications not expressly authorized by manufacturer may invalidate the users right to operate this equipment. Ce produit ou logiciel contient du code de chiffrement qui ne peut tre export ou transfr du Canada ou des tats-Unis sans un permis dexportation du dpartement du commerce des tats-Unis. Toute modification nayant pas t expressment approuve par la socit peut annuler le droit de lutilisateur de se servir du matriel. Canadian Notice / Avis pour le Canada The device for the 5150 - 5250 MHz band is only for indoor usage to reduce the potential for harmful interference to co-channel mobile satellite systems. The maximum antenna gain of 6 dBi permitted (for devices in the 5250 - 5350 MHz, 5470 5725 MHz and 5725 - 5825 MHz bands) to comply with the e.i.r.p. limit as stated in RSS-247. In addition, users are cautioned to take note that high power radars are allocated as primary users (meaning they have priority) of 5250 - 5350 MHz and 5650 - 5850 MHz and these radars could cause interference and/or damage to LE-LAN devices. Avis pour le Canada Le matriel destin un usage sur la bande 5 150 - 5 250 MHz doit tre utilis uniquement lintrieur afin de rduire les risques de brouillage nuisible caus aux systmes mobiles par satellite fonctionnant sur un mme canal. Un gain dantenne de 6 dBi est autoris (pour le matriel utilisant les bandes 5 250 - 5 350 MHz, 5 470 - 5 725 MHz et 5 725 - 5 825 MHz), conformment la limite p.i.r.e. maximale permise affrent aux priphriques RSS-247. En outre, les utilisateurs doivent prendre garde au fait que les radars de grande puissance sont considrs comme des utilisateurs principaux (ce qui signifie quils sont prioritaires) des bandes 5 250 - 5 350 MHz et 5 650 - 5 850 MHz et quils pourraient causer des interfrences et/ou des dommages aux appareils de rseau exempts de licence. LASER SAFETY LASER has been tested and classified as a Class 2 LASER Product to the stan-dard IEC 60825-1:2014. The Standard also states that the following be included in all user documentation, spec sheets, and brochures, which describe this product:

"Caution - Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure."

Note: This warning states that altering the inner parts of the laser engine in a way not specified in the user guide may cause light levels to exceed Class 2 limits. It is not an issue when using under normal conditions. Version 1.0

 

 

xPico 200 Series Embedded Wi-Fi Gateway Data Sheet Part Number 900-818 Revision QP TBDAugust 2023 Table of Contents 1. Functional Description 7 Overview _________________________________________________________________ 7 Applications _______________________________________________________________ 7 Product Features ___________________________________________________________ 8 2. Hardware and Software Description 9 xPico 200 Block Diagram ___________________________________________________ 11 Software Features _________________________________________________________ 11 3. Pin and Pad Definitions 16 4. Interfaces 23 Configurable General Purpose I/O Pins (GPIO) __________________________________ 25 System Pins ______________________________________________________________ 26 Strap Pins _______________________________________________________________ 27 5. IEEE 802.11 Wireless Lan Specifications 6. Bluetooth Specifications 7. Antenna Connection Options 28 32 33 8. Electrical Characteristics 3534 Recommended Operating Conditions ________________________________________ 3534 DC Characteristics Digital I/O Signals ______________________________________ 3534 Dynamic Power Management Modes ________________________________________ 3635 Output Power ___________________________________________________________ 3837 Input Power ____________________________________________________________ 3938 EVM __________________________________________________________________ 4039 RX Sensitivity___________________________________________________________ 4039 Power, Reset, Wake, Shutdown and Default Timing ____________________________ 4140 SPI Slave Timing ________________________________________________________ 4342 SPI Master Timing _______________________________________________________ 4443 Memory _______________________________________________________________ 4544 9. Package Description and Mechanical Footprint 4645 Dimensions ____________________________________________________________ 4645 Material and Weight ______________________________________________________ 4847 xPico 200 Series Embedded Wi-Fi Gateway Data Sheet 2 10. Product Information Label 4948 11. Compliance 5049 Labeling of the End Product _______________________________________________ 5150 Federal Communication Commission Interference Statement (xPico 240/250/270) ____ 5251 Industry Canada Statement (xPico 240/250/270): ______________________________ 5352 RoHS, REACH, and WEEE Compliance Statement _____________________________ 5958 12. Ordering Information 6059 Warranty ______________________________________________________________ 6160 Contact Information ______________________________________________________ 6160 xPico 200 Series Embedded Wi-Fi Gateway Data Sheet 3 List of Figures Figure 2-1 xPico 240 Module Options _____________________________________________ 10 Figure 2-2 xPico 250 and xPico 270 Module Options _________________________________ 10 Figure 2-3 xPico 200 Block Diagram ______________________________________________ 11 Figure 2-4 Wi-Fi Integration Mode ________________________________________________ 12 Figure 2-5 Wireless Microcontroller Mode __________________________________________ 12 Figure 3-1 xPico 200 Edge Connector Pin & Signal Location ___________________________ 16 Figure 3-2 xPico 200 PCB Interface Pin & Signal Location _____________________________ 18 Figure 8-1 Reset Timing______________________________________________________ 4140 Figure 8-2 Reset to Defaults Timing ____________________________________________ 4140 Figure 8-3 Wake Timing ______________________________________________________ 4140 Figure 8-4 SPI Slave Timing __________________________________________________ 4342 Figure 8-5 SPI Master Timing _________________________________________________ 4443 Figure 9-1 xPico 200 Embedded Wi-Fi Gateway (On-Module Antenna) _________________ 4645 Figure 9-2 xPico 200 Embedded Wi-Fi Gateway (Dual U.FL) _________________________ 4645 Figure 9-3 Layout Footprint for xPico 200 Enterprise Wi-Fi IoT Module ________________ 4746 Figure 9-4 xPico 200 Edge Connector Footprint Dimensions _________________________ 4847 Figure 10-1 xPico 200 Module Label ____________________________________________ 4948 Figure 11-2 EU Declaration of Conformity (xPico 240 / xPico 250 / xPico 270) ___________ 5655 Figure 11-3 UK Declaration of Conformity (xPico 240 / xPico 250 / xPico 270) ___________ 5756 xPico 200 Series Embedded Wi-Fi Gateway Data Sheet 4 List of Tables Table 3-1: xPico 200 Edge Connector Signal Descriptions _________________________ 17 Table 3-2: xPico 200 PCB Interface Signal Descriptions ___________________________ 19 Table 4-1 xPico 200 UART Signal Definitions ___________________________________ 23 Table 4-2 xPico 200 USB Host Interface Signal Definitions _________________________ 24 Table 4-3: xPico 200 SPI Slave Interface Signal Definitions _________________________ 25 Table 4-4: xPico 200 SPI Master Interface Signal Definitions ________________________ 25 Table 4-5: xPico 200 Module GPIO Signal Definitions _____________________________ 26 Table 4-6: xPico 200 Strap Pins ______________________________________________ 27 Table 5-1: xPico 200 Module Radio Specification _________________________________ 28 Table 5-2: 20 MHz Channels _________________________________________________ 28 Table 5-3: 40 MHz Channels _________________________________________________ 30 Table 5-4: 80 MHz Channels (xPico 270 only) ___________________________________ 30 Table 5-5: Wireless Throughput, 802.11ac, TCP _________________________________ 30 Table 5-6: Wireless Throughput, 802.11ac, UDP _________________________________ 30 Table 5-7: Wireless Throughput, 802.11n, TCP __________________________________ 31 Table 5-8: Wireless Throughput, 802.11n, UDP __________________________________ 31 Table 6-1: xPico 200 BT Radio Specification (xPico 250/270 only) ___________________ 32 Table 7-1: External Antenna Options __________________________________________ 33 Table 7-2: On-module Antenna Options ______________________________________ 3433 Table 8-1: Recommended Operating Conditions for xPico 200 Module ______________ 3534 Table 8-2: DC Characteristics & Digital I/0 Signals ______________________________ 3534 Table 8-3: xPico 200 Power Consumption 2.4 GHz (@ 3.3 V, 25o C), Bluetooth Disabled 3635 Table 8-4: xPico 200 Power Consumption 5 GHz (@ 3.3 V, 25o C), Bluetooth Disabled _ 3736 Table 8-5: xPico 250/270 Power Consumption with Bluetooth Enabled (@ 3.3 V, 25oC) 3736 Table 8-6: xPico 200 Module RF Output Power (Wi-Fi Conducted) _________________ 3837 Table 8-7: xPico 200 Module RF Output Power (BT Conducted) ___________________ 3837 Table 8-8: xPico 200 Module RF Input Power Wi-Fi 2.4 GHz ______________________ 3938 Table 8-9: xPico 200 Module RF Input Power Wi-Fi 5 GHz _______________________ 3938 Table 8-10: xPico 200 Module RF Input Power BT ______________________________ 3938 Table 8-11: xPico 200 Module Wi-Fi EVM ____________________________________ 4039 Table 8-12: xPico 200 Module Rx Sensitivity @ 3.3 V input power, +25o C ___________ 4039 Table 8-13: Shutdown Pin Timing ___________________________________________ 4241 Table 8-14: SPI Slave Timing ______________________________________________ 4342 Table 8-15: SPI Master Timing _____________________________________________ 4443 Table 9-1: Material and Weight _____________________________________________ 4847 Table 10-1: Datamatrix ECC200 Barcode Standard Descriptions __________________ 4948 Table 11-1: Country Certifications (xPico 240/250/270) __________________________ 5049 Table 11-2: Country Transmitter IDs (xPico 240) _______________________________ 5150 Table 11-3: Country Transmitter IDs (xPico 250) _______________________________ 5150 Table 11-4: Country Transmitter IDs (xPico 270) _______________________________ 5150 Table 11-5: Europe EU Declaration of Conformity (xPico 240/250/270) ___________ 5857 Table 12-1: xPico 240 Order Information _____________________________________ 6059 xPico 200 Series Embedded Wi-Fi Gateway Data Sheet 5 Table 12-2: xPico 250 Order Information _____________________________________ 6059 Table 12-3: xPico 270 Order Information _____________________________________ 6059 xPico 200 Series Embedded Wi-Fi Gateway Data Sheet 6 1. Functional Description Overview The Lantronix xPico 200 series of embedded IoT gateways is one of the smallest and most highly integrated industrial Wi-Fi, Ethernet and Bluetooth combo solutions, allowing you to deliver and manage secure connected products without added complexity and risk. The xPico 200 series delivers always-on dual-band enterprise Wi-Fi, dual-mode Bluetooth

(Bluetooth Classic v2.1+EDR and Bluetooth Low Energy v4.2) as well as Ethernet connectivity for business-critical assets. It is a standalone module that does not require an external host processor for the wireless and network stack. With customer proven TruPort technology that includes production-ready essential IoT connectivity firmware, cloud-based management and an integrated device security framework, xPico 200 series delivers a complete network and IoT connectivity offload solution for any microcontroller. Device manufacturers can use xPico 200 series as the wireless microcontroller within their device and focus on the application firmware components while leveraging the integrated secure connectivity network and cloud service enablement capabilities within the module. The high performance xPico 200 series is available in different versions

(see Product FeaturesProduct Features). Formatted: xref With the xPico 200 family, design engineers and system architects can reduce product development time and deploy their secure connected devices with confidence that their products will connect and work as expected. Applications For applications that need Ethernet and wireless connectivity options, xPico 200 delivers a compact combo solution without needing to integrate two different network stacks from different modules or controllers. Integrated Bluetooth capability on xPico 250/270 enables gateway functions that need to aggregate Bluetooth sensor devices or communicate with Bluetooth peripherals and mobile devices. Key applications include:

Medical devices Industrial machines Retail/POS Weighing scales Asset and warehouse management Environmental monitoring Transportation and Telematics The xPico 200 series is designed for applications in a variety of industries where reliability, extended operating temperature range, and robust wireless connectivity are business-critical. The xPico 200 series is also particularly well-suited for products with long lifecycles in highly xPico 200 Series Embedded Wi-Fi Gateway Data Sheet 7 regulated industries where the constant change in Wi-Fi technologies and certification would typically make it difficult or cost prohibitive to incorporate a wireless solution. Product Features Dual-band (802.11 a/b/g/n) for high performance industrial Wi-Fi xPico 270 adds 802.11ac 2.4 GHz and 5 GHz bands supported IEEE 802.3 10/100 Mbps Ethernet (RMII) Compliant with Bluetooth Core Specification version 4.2 including BLE - xPico 250/270 Support for Bluetooth Generic Access Profile (GAP), Generic Attribute Profile (GATT), Device ID Profile - xPico 250/270 On-module antenna or Dual U.FL UART (x1), SPI Master (x1), SPI Slave (x1), USB Host/Device and GPIO Ethernet MAC (RMII), USB, UART host interfaces Simultaneous AP and client (STA), AP only, client (STA) only modes Support for up to 5 simultaneous client connections to Soft AP interface TruPort Serial and TruPort Socket providing industrys most compatible device data access technology InfiniShield Security adding integrated root of trust security and data-at-rest and data-

in-motion encryption, authentication and identification Direct mobile to device service interface via Soft AP technology (xPico 240/250/270) or Bluetooth (xPico 250/270) WPA/WPA2/WPA3-Personal, WPA2-Enterprise, and WPA3-Enterprise Transition Mode Wi-Fi Security (WPA3 supported in STA mode only) SSL/TLS 1.2 with X.509 Certificate Management Dual Network Support Bridge Ethernet to Wi-Fi STA or to Soft AP Integrated Cloud Based Device Management via ConsoleFlow platform Web Service API, XML Configuration, Serial Command API Modular RF Certification (FCC, IC, ETSI, Japan, AU/NZS, China) Compact SMT (LGA) Footprint (17mm x 25 mm) or Edge Connector Card Footprint (22 mm x 35.5 mm) Operating temperature range: -40C to +85C 5-year limited warranty xPico 200 Series Embedded Wi-Fi Gateway Data Sheet 8 2. Hardware and Software Description The xPico 200 series is a highly integrated module that includes a Cortex R4 controller, 802.11 a/b/g/n MAC/BB, 10/100 Mbps Ethernet MAC, Bluetooth 4.2 (on xPico 250/270), RAM, flash, and two U.FL antenna connectors or a single on-module antenna (on the xPico 240 only). xPico 270 adds 802.11ac. The module also includes the following data communication interfaces:

One 10/100 Mbps Ethernet MAC with RMII interface for connection to an external PHY One USB 2.0 high speed Host/Device port One 300 to 4Mbps UART with hardware flow control One SPI Slave port operating up to 50 MHz clock rate (5 Mbps application throughput) Up to 12 GPIO lines The xPico 200 series operates on 3.3V power with 3.3V logic, and has a built-in voltage supervisory circuit. xPico 200 series offers two main variants depending on the connectivity interfaces available:

xPico 240 - Provides dual-band 802.11abgn Wi-Fi and Ethernet combo xPico 250 - Provides dual-band 802.11abgn Wi-Fi, Ethernet and dual-mode Bluetooth

(Bluetooth Classic and Bluetooth Low Energy) xPico 270 - Provides dual-band 802.11ac/abgn Wi-Fi, Ethernet and dual-mode Bluetooth

(Bluetooth Classic and Bluetooth Low Energy) The xPico 200 comes in two form factors:

Small form factor SMT module Edge connector module with standard connector xPico 240 has two antenna options:

Two U.FL for connection to external antennas for single stream diversity. See Antenna Connection Options for recommended antennas. Single on-module antenna xPico 250 and xPico 270 have one antenna option:

Two U.FL for connection to external antennas. One antenna dedicated for Wi-Fi and one dedicated for BT. See Antenna Connection Options for recommended antennas. xPico 200 Series Embedded Wi-Fi Gateway Data Sheet 9 Figure 2-1 xPico 240 Module Options XPC2401 LGA, Dual U.FL XPC2402 LGA, On-Module Antenna XP2403 Edge Connector, Dual U.FL XPC2404 Edge Connector, On-Module Antenna Figure 2-2 xPico 250 and xPico 270 Module Options XPC2501, XPC2701 LGA, Dual U.FL XPC2503, XPC2703 Edge Connector, Dual U.FL xPico 200 Series Embedded Wi-Fi Gateway Data Sheet 10 xPico 200 Block Diagram Figure 2-3 xPico 200 Block Diagram Software Features The xPico 200 embedded gateway software stack provides essential IoT connectivity infrastructure for building secure connected products. Device manufacturers can offload this complexity from their application microcontroller when interfacing with the module in Network Co-processor Mode or use the module standalone in Wireless Microcontroller Mode

(Hostless). Network Co-Processor Mode The module completely offloads all Wi-Fi and secure network connectivity requirements for attached microcontrollers thereby reducing device firmware complexity while accelerating OEMs time to introduce and support secure connected products in the market. The host interfaces available for connecting to the microcontroller are UART, USB, SPI Slave, and Ethernet. xPico 200 Series Embedded Wi-Fi Gateway Data Sheet 11 Figure 2-4 Wi-Fi Integration Mode Wireless Microcontroller Mode In addition, the xPico 200 series also can be used as a wireless microcontroller in standalone mode. With the provided SDK, device manufacturers can leverage not only network and wireless stacks, but also the complete application framework that includes the configuration management system, reliable remote OTA firmware upgrades and automated connection management features described below. Figure 2-5 Wireless Microcontroller Mode xPico 200 Series Embedded Wi-Fi Gateway Data Sheet 12 TruPort Serial TruPort Serial, a robust serial to Wi-Fi and serial to Ethernet application that supports the transparent transport of hundreds of serial protocols over the network. TruPort Serial is very suitable for use in network co-processor mode based applications requiring very little to no programming and development effort. Key capabilities included are:

Support RS232 serial and USB (CDC Serial and CDC ACM device classes) Advanced connectivity modes and configuration knobs to tune the connection parameters for a specific protocol without requiring custom software programming Automatic and Manual connect modes Inbound (Accept Mode) and Outbound (Connect Mode) connections Modem Emulation Mode enables connecting to different servers using a standard AT command set AES (128-bit, 192-bit, 256-bit) Encrypted session and TLS session modes for secure tunneling TruPort Socket Connect your device microcontroller to multiple services and communicate directly with mobile devices and cloud services at the same time via TruPort Socket. The simple API for TruPort Socket is available via the UART, SPI Slave, or USB interface operating in CDC ACM mode. Seamlessly switch between Data Mode and Module Management Mode (CLI access) for total control and data channel access from your device host microcontroller. Access TCP, UDP, TLS, HTTP, SMTP channels and communicate with external services through these channels without implementing these protocol stacks within your microcontroller. Ethernet to Wi-Fi Bridge For devices with microcontrollers that include a network stack and also have Ethernet connectivity available, the gateway module software provides wireless connectivity to these devices via the Ethernet to Wi-Fi Bridge mode. Ethernet connected host devices can be accessed remotely via the Wi-Fi Client interface or via the Wi-Fi Soft AP interface. In this mode, the Wi-Fi stack is fully offloaded and managed via the configuration interface. This mode is most suitable for networked microcontrollers that do not have the resources to integrate wireless device drivers and add-on the complexity of managing the wireless stack. Concurrent Soft AP and Client Mode In addition to supporting the standard Soft AP only mode, Client only mode, xPico 200 series also supports concurrent Soft AP and Client mode. In this mode, clients can create a direct connection to the Soft AP interface of the gateway, while the Client interface is connected to the Enterprise Wi-Fi network. This enables OEM service and support teams to setup a direct connection to their machines to diagnose, troubleshoot and service them via mobile devices without requiring access to the customer's Wi-Fi network. xPico 200 Series Embedded Wi-Fi Gateway Data Sheet 13 Enterprise Wi-Fi Security (802.11i, 802.1X/EAP) Centralized control of security policies and ability to permit and revoke access rights and scaling to support the large number of devices deployed within the enterprise are primary considerations that Enterprise Wi-Fi Security addresses. With support for 802.1X, 802.11i and EAP authentication methods along with support PKI support and X.509 certificate management, connectivity to the enterprise network is handled via configuration and without any integration, testing and certification of supplicant and authenticator software. InfiniShield Security Device manufacturers are exposed to new security risks that emerge with having connected products. They also have to navigate the engineering complexity of providing integrated security within their connected devices. Lantronix InfiniShield Security provides an integrated device security framework that lets device manufacturers build this into their connected products from the start of their design cycle instead of as an after-thought or bolted on component. InfiniShield Security enables building secure connected products quickly and easily with a full range of features including:

Secure Boot run only signed software on device Secure Firmware Over the Air (FOTA) accept signed firmware and reliable over the air updates Secure Connectivity enterprise Wi-Fi security, data-in-motion authentication and encryption Encrypted Storage stored configuration and device data securely Fine Grained Port Access Control prevent back-doors with fine grained control over network ports Root of Trust and Device Identity certificate management, secure key storage, OEM keys Wi-Fi Connection Profiles Connect to multiple wireless networks autonomously by configuring the network parameters once and then letting the module automatically select the best network to connect to or set policies for connecting to specific networks. Wi-Fi connection profiles eliminate the need to manage the state of connection management from the device microcontroller or writing this via the SDK in wireless microcontroller mode. Configuration and Management Interface Access the module configuration and management engine via the microcontroller or via the network. Command Line Interface (CLI) mode offers a text based interactive interface versus writing an elaborate driver interface for the AT command and control interface on the device microcontroller. XML provides a programmatic interface to the module configuration and status that is accessible via the available host interfaces or over the network interface. Web API offer the ability to program the module configuration via the Over-The-Air (OTA) or Network interface. For more details on the usage of these management interfaces, refer to the xPico 240/250 Embedded Wi-Fi Gateway User Guide available at https://www.lantronix.com/products/xpico-200/ for more details. xPico 200 Series Embedded Wi-Fi Gateway Data Sheet 14 Reliable Firmware Over-The-Air (FOTA) Updates As device requirements evolve and new product features are provided, device manufacturers can leverage the reliable OTA firmware upgrade capabilities to prevent system bricks. OTA firmware upgrade always ensures there is at-least one known version of firmware available in the event an upgrade operation does not succeed. It operates over the connected network and does not require placing the module into specific operational modes into order to trigger the update. Updates can be performed remotely and securely using the included Secure Boot features. Power Management xPico 200 series gateways support IEEE 802.11 power save modes for radio power management. The gateways also include application aware power management framework that enables battery powered operation. Pre-integration with ConsoleFlow Platform Quickly deliver secure and robust web-scale device management and monitoring for your connected products with ConsoleFlow management software. Pre-integrated support within xPico 200 series gateways enables your connected products and the gateway to be managed across the product lifecycle from deployment to decommissioning. Remote Gateway Management with Lantronix Gateway Central Leverage powerful monitoring and management capabilities for Lantronix gateways using Lantronix Gateway Central. Use Google-like search to quickly locate gateways, trigger centralized remote firmware updates and setup customized alerts and notifications on monitoring parameters across your fleet of Lantronix gateways. With Lantronix Gateway Central, you can maintain a consistent factory configuration or default field configuration or stay on an approved firmware baseline without paying for custom programming services. Integrated Bluetooth Classic and Bluetooth Low Energy Stacks (xPico 250/270) Implement custom BLE profiles with the available SDK and leverage the underlying Bluetooth Stack that complies with Bluetooth Core Specification version 4.2 including BR/EDR/BLE, supports Generic Access Profile (GAP) and Generic Attribute Profile (GATT). It provides support for BLE Central role to enable communication with various BLE sensors and peripherals. As a BLE peripheral it enables communication with mobile devices. Utilize the pre-integrated Lantronix Gateway Provisioning Profile along with the Gateway Provisioning mobile application to bootstrap initial gateway wireless and network configuration from mobile devices. Leverage the integrated connection management to pair, bond, and connect with Bluetooth Classic (BR/EDR) devise. Supports the following BT Classic Profiles:

Serial Port Profile (SPP) Client and Server* mode A2DP* (Data mode only) xPico 200 Series Embedded Wi-Fi Gateway Data Sheet 15 3. Pin and Pad Definitions Table 3-2 describes the xPico 200 Wi-Fi interface signal definition. The Signal Name column identifies the signal pin being described while the Primary Function column provides definitions of the signal pin depending upon the member of the xPico 200 family being used. Differentiating the signal pins is beneficial when using multiple xPico 200 device types on a single platform. Figure 3-1 xPico 200 Edge Connector Pin & Signal Location ANT2 WI-FI DIVERSITY

(or BLUETOOTH) ANT1 2X U.FL WI-FI xPico 200 Series Embedded Wi-Fi Gateway Data Sheet 16 Table 3-1: xPico 200 Edge Connector Signal Descriptions 0BPin 1BSignal 2BPin 3BSignal 1 3 5 7 9 11 13 15 17 19 21 23 33 35 37 39 41 43 45 47 49 51 53 55 57 59 61 63 65 67 69 71 73 75 GND USB_D+

USB_D-

GND SDIO_SCK/SPI_CLK (slave) SDIO_CMD/SPI_MOSI (slave) SDIO_DATA0/SPI_MISO (slave) SDIO_DATA1/SPI_IRQ (slave) SDIO_DATA2 2 4 6 8 10 12 14 16 18 3.3V 3.3V SYS_LED NC NC USB_H/D_SEL SDIO_MODE/SPI_SLAVE_MODE CP9/LED GND SDIO_DATA3/SPI_CS (slave) 20 WAKE NC DEFAULT#

GND TDO TDI GND TCK TMS GND RMII_MDC RMII_MDIO GND RMII_RXD1 RMII_RXD0 GND NC RMII_CLK GND RMII_RXDV RMII_TXEN GND RMII_TXD1 RMII_TXD0 GND 22 32 34 36 38 40 42 44 46 48 50 52 54 56 58 60 62 64 66 68 70 72 74 UART_TXD UART_RXD UART_RTS UART_CTS TRST CP8/CS (master) CP7/SCK (master) CP4/MOSI (master) CP3/MISO (master) CP2/INT (master) CP1 RESET#

I2C2_CLK I2C2_DATA CP5/I2C_DATA CP6/I2C_CLK CP10/PWM NC RSVD_CP12 RSVD_CP11 RMII_RST 3.3V 3.3V xPico 200 Series Embedded Wi-Fi Gateway Data Sheet 17 Figure 3-2 xPico 200 PCB Interface Pin & Signal Location xPico 200 Series Embedded Wi-Fi Gateway Data Sheet 18 Table 3-2: xPico 200 PCB Interface Signal Descriptions 4BSignal Name 5BPrimary Function 6BxPico 200 SMT Pin 7BEdge Connector Pin 8BDriver Strength GND SDCK/SPI_CLK (slave) SDCMD/SPI_MOSI (slave) SDIO0/SPI_MISO (slave) SDIO1/SPI_IRQ (slave) Signal Ground SDIO Clock/SPI Slave Clock SDIO CMD/SPI Master Out-Slave In SDIO Data 0/SPI Master In-Slave Out SDIO Data 1/SPI Slave Interrupt SDIO2 SDIO Data 2 SDIO3/SPI_CS (slave) CP3/MISO (master) CP4/MOSI (master) CP7/SCK (master) CP8/CS (master) CP2/INT (master) I2C Data 2 I2C Clock 2 CP5/I2CDATA*

CP6/I2CCLK*

WAKE GND USB+

USB-

GND CP9/PWM/LED RMII_TXD0 SDIO Data 3/SPI Slave chip select Configurable I/O- SPI MISO Configurable I/O-SPI MOSI Configurable I/O-SPI Clock Configurable I/O-SPI Chip Select Configurable I/O-SPI interrupt input I2C Bus 2 data I2C Bus 2 clock Configurable I/O-

I2CDATA Configurable I/O-I2CCLK Toggle signal from low to high to WAKE from Power down (Standby) state. This pin must be pulled high with a 100K ohm resistor. Note: signal is noise sensitive. Filter as close as possible to module pin. Signal Ground USB Port Positive pin USB Port Negative pin Signal Ground Configurable I/O-PWM RMII TXD0 transmit output 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 1 9 11 13 15 17 19 46 44 42 40 48 56 54 58 60 20 7 3 5 33 16 73 8 mA 8 mA 8 mA 8 mA 8 mA 8 mA 8 mA 8 mA 8 mA 8 mA 8 mA 8 mA 8 mA 8 mA 8 mA 8 mA xPico 200 Series Embedded Wi-Fi Gateway Data Sheet 19 4BSignal Name 5BPrimary Function 6BxPico 200 SMT Pin 7BEdge Connector Pin 8BDriver Strength 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 71 61 12 67 70 14 65 55 53 6 39 47 49 62 50 66 68 52 8 mA 8 mA RMII_TXD1 RMII_CLK USB_H/DEV_SEL RMII_TXEN RMII_RST RMII TXD1 transmit output RMII interface clock USB Host/Device Mode Select Pull high for device mode on USB Pull low for host mode on USB Connect to ID pin of USB connector RMII transmit enable output RMII reset output SDIO_MODE/SPI_SLAVE_MODE SDIO Master/Slave select Pull high for master mode on SDIO. Pull low for slave mode on SDIO/SPI. RMII_RXDV RMII_RXD0 RMII_RXD1 SYS_LED GND MDC MDIO CP10/PWM CP1 RESERVED1 RESERVED2 EXT_RESET#

RMII RX data valid input RMII RXD0 receive input RMII RXD1 receive input System status LED, active high Signal Ground MDIO clock MDIO data Configurable I/O-PWM Configurable I/O Reserved for future UART RX output Reserved for future UART TX output Unit hardware reset, active low. Drive low for 50ms to reboot unit. Signal should be driven high or pulled high after assertion. EXT_RESET#

is inactive during module power down (standby) state. Assert WAKE signal to come out of low power states prior to asserting reset. CTS1 Serial clear-to-send input 42 36 8 mA xPico 200 Series Embedded Wi-Fi Gateway Data Sheet 20 4BSignal Name 5BPrimary Function 6BxPico 200 SMT Pin 7BEdge Connector Pin 8BDriver Strength VCC VCC VCC RTS1 RXD1 TXD1 TMS TCK TDI TDO TRST GND DEFAULT GND GND GND GND GND GND GND GND_PADS Notes:

8 mA 8 mA Power input. Must be connected to 3.3V power supply Power input. Must be connected to 3.3V power supply Power input. Must be connected to 3,3V power supply Serial ready-to-send (232)

/ serial transmit enable

(485) output 43 44 45 46 Serial receive data input 47 Serial transmit data output 48 JTAG TMS Input JTAG Clock Input JTAG Data Input JTAG Data Output JTAG Reset Input Signal Ground Drive low for 6 seconds or longer to reset unit to default settings. Signal Ground Signal Ground Signal Ground Signal Ground Signal Ground Signal Ground Signal Ground Signal Ground 49 50 51 52 53 54 57 58 59 60 61 64 65 66 67,68,69, 70,71,72, 73,74,75 74 72 2,4 34 32 22 43 41 37 35 38 45 23 51 57 63 69 75 18 1. The current module supports an external 10/100 Mbps Ethernet PHY via the RMII interface. 2. The logic IO pins are 3.3V tolerant. 3. SMT Pins 67 to 75 are the ground pads under the module. These pads must be connected to ground. These pads also provide thermal relief for the module. It is recommended that multiple vias for each pad be used to connect the ground pads to the ground plane. Please see the evaluation board layout as a reference for the ground pad xPico 200 Series Embedded Wi-Fi Gateway Data Sheet 21 and multiple via in pad recommendation. Contact your local FAE or sales support for the evaluation kit artwork. 4. All unused IO pins may be left floating, except for the required straps on pins 17, 26, and 29. 5. Asterisk (*) indicates feature available in a future release. Contact your local sales representative for availability. xPico 200 Series Embedded Wi-Fi Gateway Data Sheet 22 4. Interfaces The xPico 200 module offers a number of interfaces to allow for easy connectivity to the module. These include 10/100 Mbps Ethernet MAC with RMII, UART for asynchronous serial communication, SPI Master and SPI Slave for synchronous formatted data, and USB interface. Ethernet The xPico 200 module has an integrated 10/100 Mbps Ethernet MAC and with an RMII interface. External PHY, magnetics and RJ45 are required for connection to a standard Ethernet network. See the xPico 200 Series Embedded Wi-Fi Gateway Integration Guide available at https://www.lantronix.com/products/xpico-200/ for more details. UART The xPico 200 module supports one UART interface The UART supports asynchronous data rate up to 4 Mbps, with Odd/Even parity, and 1

& 2 stop bits Software flow control (Xon, Xoff) Operational mode as a DTE device UART supports TX, RX, RTS, CTS (hardware flow control) Table 4-1 xPico 200 UART Signal Definitions 10BDescription 11BSMT Pin 12BEdge Conn. Pin Serial transmit data output Serial ready-to-send/serial transmit enable output Serial receive data input Serial clear-to-send input 48 46 47 42 22 34 32 36 9BPin Name TXD1 RTS1 RXD1 CTS1 xPico 200 Series Embedded Wi-Fi Gateway Data Sheet 23 USB Host Interface Table 4-2 xPico 200 USB Host Interface Signal Definitions 13BPin Name 14BDescription 15BSMT Pin 16BEdge Conn. Pin 17BSignal Requirement 18BType A USB Host Conn. Pin USB+/HHSDPB USB HS Host Port A 19 Positive pin USB-/HHSDPM USB HS Host Port A 20 3 5 Negative pin 5V power for USB connector 5V (User-

supplied) Ground Signal Ground Ground Ground Ground plane USB_H/D_SEL USB Host/Device 26 12 Mode Select 3 2 1 4 Route as 90 ohm differential pair Route as 90 ohm differential pair Current limit to 500 mA per port Pull low for host mode. Connect to ID pin of USB connector if using A/B or Type C connector Pull high for Host Mode USB Host Power Enable

(CP2) USB Host Port Over Current Flag (CP1) Output to enable external USB power switch for host port connector (Use configurable CP2) Input from external USB power switch indicating the host port is over current

(Use configurable CP1) 12 48 38 50 Pull high for Host Mode xPico 200 Series Embedded Wi-Fi Gateway Data Sheet 24 SPI Slave Interface The xPico 200 gateway has one external SPI slave interface for connection an external SPI master using the gSPI implementation. The signal levels on the SPI slave interface are 3.3V tolerant. This interface is shared with the SDIO interface pins. SDIO is not available in the current product release. Note: The SPI master interface uses different pins than the SPI slave interface. Table 4-3: xPico 200 SPI Slave Interface Signal Definitions 19BPin Name 20BDescription SPI_CLK SPI_MOSI SPI_MISO SPI_IRQ SPI_CS SPI Slave Clock SPI Master Out-Slave In SPI Master In-Slave Out SPI Slave Interrupt SPI Slave Chip Select SDIO_MODE/SPI_SLAVE_MODE Master/Save Pull high for master mode (not currently supported) Pull low for slave mode 21BSMT Pin 22BEdge Conn. Pin 2 3 4 5 7 29 9 11 13 15 19 14 SPI Master Interface The xPico 200 gateway has one external SPI master interface for connection an external SPI slave. The signal levels on the SPI interface are 3.3V tolerant. This interface is shared with the configurable GPIO pins. Note: The SPI slave interface uses different pins than the SPI master interface. Table 4-4: xPico 200 SPI Master Interface Signal Definitions 23BPin Name 24BDescription CP7/SPI_CLK SPI Clock CP4/SPI_MOSI SPI Master Out-Slave In CP3/SPI_MISO SPI Master In-Slave Out CP2/SPI_IRQ SPI Interrupt CP8/SPI_CS SPI Chip Select 25BSMT Pin 26BEdge Conn. Pin 10 9 8 12 11 42 44 46 48 40 Configurable General Purpose I/O Pins (GPIO) The xPico 200 module provides up to 12 configurable General Purpose Input/Output (GPIO) pins. Certain GPIOs are multiplexed with other interface functions (e.g. SPI). Mapping of these functions to CPs will be driven via configuration and applied at system initialization. Each CP can be configured as a general purpose input, general purpose output, micro-

controller peripheral block or a soft function. These pins are 3.3V CMOS logic level tolerant. xPico 200 Series Embedded Wi-Fi Gateway Data Sheet 25 Table 4-5: xPico 200 Module GPIO Signal Definitions 27BPin Name 28BDescription 29BReset State 30BxPico 200 SMT Pin 31BEdge Connector Pin CP1 Configurable I/O-USB Over Current Flag CP2/INT CP3 CP4 CP5 CP6 CP7 CP8 CP9 CP10 CP11 CP12 Configurable I/O-SPI interrupt input-USB Host Port Power Enable Output Configurable I/O-SPI MISO1 Configurable I/O-SPI MOSI1 Configurable I/O-I2C bus data1 Configurable I/O-I2C bus clock1 Configurable I/O-SPI Clock1 Configurable I/O-SPI Chip Select1 Configurable I/O-PWM Configurable I/O-PWM Configurable I/O Configurable I/O Input Input Input Input Input Input Input Input Input Input Input Input 38 12 8 9 15 16 10 11 22 37 40 39 50 48 46 44 58 60 42 40 16 62 68 66 1 SPI/I2C Interfaces (SPI Master) are reserved for a future update. Contact your local sales representative for availability. System Pins The xPico 200 module has three system pins:

EXT_RESET# is the unit hardware reset, active low. Drive low for 50 ms to reboot unit. Signal should be driven high or pulled high after reset. EXT_RESET# is inactive during module power down (standby) state. Assert WAKE signal to come out of low power states prior to asserting reset. DEFAULT# is the unit reset to default, active low. Drive low for 6 seconds or longer to reset unit to default settings. May be left floating if unused. WAKE is the toggle signal to WAKE from the STANDBY state. WAKE signal is noise sensitive. Filter as close as possible to the module pin. See the xPico 200 Series Embedded Wi-Fi Gateway Integration Guide available at https://www.lantronix.com/products/xpico-200/ for more details. xPico 200 Series Embedded Wi-Fi Gateway Data Sheet 26 Strap Pins The xPico 200 module has two strap pins for setting the mode of the USB and SDIO ports. The SDIO port is reserved for a future update. These pins must be strapped high or low. The mode definitions are listed below. 32BPin Name 33BDescription Table 4-6: xPico 200 Strap Pins USB_H/D_SEL Pull high for device mode on USB port. Pull low for host mode on USB port. SDIO_MODE/SPI_SLAVE_MODE Pull high for master mode on SDIO port. Pull low for slave mode on SDIO port. 34BxPico 200 SMT Pin 35BEdge Connector Pin 26 29 12 14 xPico 200 Series Embedded Wi-Fi Gateway Data Sheet 27 5. IEEE 802.11 Wireless Lan Specifications Table 5-1Table 5-1 below provides the specifications and performance attributes for the xPico 200 module IEEE 802.11 radio. Table 5-1: xPico 200 Module Radio Specification 36BFeature Frequency Band Supported Data Rates xPico 240/250 Supported Data Rates xPico 270 only Modulation 802.11 MAC Features 802.11 Modes 37BDescription 2.412 2.484 GHz (20 MHz channels) 5.18 to 5.845 GHz (20 and 40 MHz channels) 5.18 to 5.845 GHz (20, 40, and 80 MHz channels) (xPico 270 only) Channels dependent on assigned country code. See channel list below. 802.11abgn a, b, g data rates up to 54 Mbps n data rates up to MCS7 802.11ac/abgn a, b, g data rates up to 54 Mbps n data rates up to MCS7 ac data rates up to MCS9 OFDM with BPSK, QPSK, 16-QAM, 64-QAM (xPico 270 up to 256QAM) IEEE 801.11b with CCK and DSSS WEP, WPA, WPA2, WPA3, WMM, WMM-PS (UAPSD), WMM-SA, AES, TKIP a/b/g/n/d/h/I (xPico 270 includes ac) Frequency Channel FCC/

USA Table 5-2: 20 MHz Channels Canada Europe Australia New Japan China India Taiwan Mexico Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Zealand Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes

Yes Yes Yes Yes Yes

Yes Yes Yes Yes Yes Yes Yes

Yes Yes Yes Yes Yes Yes Yes

Yes Yes Yes Yes Yes Yes Yes

Yes Yes Yes Yes Yes Yes Yes

Yes Yes Yes Yes Yes Yes Yes

Yes Yes Yes Yes Yes Yes Yes

Yes Yes Yes Yes Yes

Yes Yes Yes Yes Yes

d n a B z H G 4

. 2 2412 2417 2422 2427 2432 2437 2442 2447 2452 2457 2462 2467 2472 2484 1 2 3 4 5 6 7 8 9 10 11 12 13 14 xPico 200 Series Embedded Wi-Fi Gateway Data Sheet 28 Frequency Channel FCC/

USA Canada Europe Australia New Japan China India Taiwan Mexico Zealand d n a B z H G 5 5180 5200 5220 5240 5260 5280 5300 5320 5500 5520 5540 5560 5580 5600 5620 5640 5660 5680 5700 5720 5745 5765 5785 5805 5825 36 40 44 48 52 56 60 64 100 104 108 112 116 120 124 128 132 136 140 144 149 153 157 161 165 Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes

Yes Yes Yes Yes Yes

Yes Yes Yes Yes Yes Yes*

Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes Yes Yes Yes Yes

Yes Yes Yes Yes Yes

* - Channel not available for ap0 when operating in standalone mode, i.e. wlan0 is disabled or not associated. xPico 200 Series Embedded Wi-Fi Gateway Data Sheet 29 Table 5-3: 40 MHz Channels Frequency Channel FCC/

USA Canada Europe Australia New Japan China India Taiwan Mexico Zealand d n a B z H G 5 5190 5230 5270 5310 5510 5550 5590 5630 5670 5755 5795 38 46 54 62 102 110 118 126 134 151 159 Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes Yes Yes Yes

Yes Yes Yes Yes

Yes Yes Yes Yes Yes*

Yes*

Yes*

Yes*

Yes*

Yes Yes

* - Channel not available for ap0 when operating in standalone mode, i.e. wlan0 is disabled or not associated. Table 5-4: 80 MHz Channels (xPico 270 only) Frequency Channel FCC/

USA Canada Europe Australia New Japan China India Taiwan Mexico Zealand d n a B z H G 5 5210 5290 5530 5610 5690 5775 42 58 106 122 138 155 Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes*

Yes*

Yes* Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes* Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes*

Yes Yes

Yes Yes

Yes Yes Yes Yes

* - Channel not available for ap0 when operating in standalone mode, i.e. wlan0 is disabled or not associated. Table 5-5: Wireless Throughput, 802.11ac, TCP 65BTCP 20 MHz 66BTCP 40 MHz 67BTCP 80 MHz 68BDownlink 69BUplink 70BDownlink 71BUplink 72BDownlink 73BUplink Mbps 47.1 54 71.3 88.1 87.6 115 Table 5-6: Wireless Throughput, 802.11ac, UDP 74BUDP 20 MHz 75BUDP 40 MHz 76BUDP 80 MHz 77BDownlink 78BUplink 79BDownlink 80BUplink 81BDownlink 82BUplink Mbps 69.2 65.7 134 125 218 201 xPico 200 Series Embedded Wi-Fi Gateway Data Sheet 30 Table 5-7: Wireless Throughput, 802.11n, TCP 83BTCP 20 MHz 84BTCP 40 MHz 85BDownlink 86BUplink 87BDownlink 88BUplink Mbps 45 49.3 67.4 77.5 Table 5-8: Wireless Throughput, 802.11n, UDP 89BUDP 20 MHz 90BUDP 40 MHz 91BDownlink 92BUplink 93BDownlink 94BUplink Mbps 59.2 58.8 109 105 Notes:

1. Frequencies from 5150 MHz to 5250 MHz for indoor use only. 2. The unit supports 20 MHz bandwidth channels for 2.4 GHz channels. 3. The unit supports 20, 40 MHz bandwidth channels for 5 GHz channels. 4. xPico 270 supports 80Mhz bandwidth channels for 5 GHz channels. 5. Country code modifications are not available to the end user. 6. If the unit is connected as a client to an external AP, the Soft AP channel follows the external AP. Otherwise, the Soft AP defaults to automatically choosing a channel based on RSSI and channel usage. A unit that is not connected to an external AP may also be configured for a specific channel. In Soft AP mode, the product will not initiate any connection or active scan in 5G DFS bands and will only follow external AP or master device to use a channel. 7. 8. Wireless throughput tests performed with iPerf in 5 GHz band, channel 36. UDP throughputs measured at approximately 0.1% packet loss. 802.11n throughput tests performed as single stream. 802.11ac and 80 MHz wireless throughput values apply only to xPico 270. xPico 200 Series Embedded Wi-Fi Gateway Data Sheet 31 6. Bluetooth Specifications The table below provides the specifications and performance attributes for the xPico 250/270 Bluetooth radio. Table 6-1: xPico 200 BT Radio Specification (xPico 250/270 only) 95BFeature 96BDescription Frequency Band 2.402 2.480 GHz Supported Standards Bluetooth core specification 4.2 including BR/EDR/BLE Modulation Power GFSK, /4-DQPSK, 8-DPSK Class 1, Class 2 xPico 200 Series Embedded Wi-Fi Gateway Data Sheet 32 7. Antenna Connection Options The xPico 200 module supports wireless connectivity via two U.FL connectors for single stream transmit and receive diversity. An on-module stamped metal antenna version is also available as a product SKU option. The single antenna is used for transmit and receive. Diversity is not available on the module with the on-module antenna. The xPico 200 modules are certified using the antennas listed in Table 7-1 and Table 7-2 below. Refer to the compliance section below for certification requirements related to antenna selection. Table 7-1: External Antenna Options 97BAntenna Type 98BPeak Gain Typical PCB strip antenna with 50 mm cable to U.FL connector With tape backing 2.5 dBi, 2.39 GHz to 2.49 GHz 5dBi, 4.9 GHz to 5.9 GHz 99BLantronix Part Number XPW100A 003-01-B 50 piece bulk pack 100BVendor 101BVendor Part Number 102BApproved Region Ethertronics 1001077 Ethertronics 1000668 PCB strip antenna with 50 mm cable to U.FL connector Without tape backing Swivel type antenna, with RP-

SMA(M) connector Swivel type antenna, with RP-

SMA(M) connector PIFA Chip 2.5 dBi, 2.39 GHz to 2.49 GHz 5 dBi, 4.9 GHz to 5.9 GHz 2 dBi, 2.4 GHz to 2.5 GHz, 2 dBi, 5.15 GHz to 5.85 GHz 3.8 dBi, 2.4 GHz to 2.5 GHz, 5.5 dBi, 4.9 GHz to 5.8 GHz 4.00 dBi for 2.4 GHz, 4.6 dBi for 5.2 Ghz to 5.3 Ghz, 5.20 dBi for 5.4Ghz to 5.7Ghz 3.00 dBi for 2.4 GHz ACC-930-

033-R Wanshih WSS002 Taoglas Wha Yu Industrial Co., Ltd. GW.71.5153

(Not for EU use) C056-

511080-A FCC, IC, NCC, JPN GainForce Technology Co., Ltd. AT9520-

B2R4HAAT-

LF FCC, IC, NCC, JPN FCC, IC, EU, AUS/NZS, JPN, China, Mexico FCC, IC, EU, AUS/NZS, JPN, China, Mexico FCC, IC, EU, AUS/NZS, JPN, China, Mexico FCC, IC, AUS/NZS, JPN, China, Mexico Note: Antenna gain listed above excludes cable loss. xPico 200 Series Embedded Wi-Fi Gateway Data Sheet 33 Table 7-2: On-module Antenna Options 103BAntenna Type 104BPeak Gain Typical On module stamped metal antenna 0 dBi 2.4 GHz, 4 dBi 5 GHz xPico 200 Series Embedded Wi-Fi Gateway Data Sheet 34 8. Electrical Characteristics Recommended Operating Conditions Table 8-1 specifies the recommended operation conditions and parameters for optimum performance of the xPico 200 module. Table 8-1: Recommended Operating Conditions for xPico 200 Module Parameter Voltage Supply Voltage Ripple/droop Extended Operating Temperature Extended Storage Temperature Humidity (non-condensing, relative) Power Supply ramp rate Vibration (Operational) Non-operational Shock Symbol Min VCC VCC pp Ta Ta VCC 3.15

-40

-40 5%

40 Typ 3.3 Max 3.45 1%

+85

+85 85 10001 40 65 i 0F Units V DC C C

Us G G 1For slower power supply ramp rates it is recommended to assert reset for 50ms after power reaches 3.15V. DC Characteristics Digital I/O Signals Table 8-2Table 8-2 describes the DC characteristics and digital I/O signals of the xPico 200 module. The RMII pins are managed by the VDDIO_RMII power segment as mentioned in the Power Supply Segments section of the datasheet (refer to Table 19 on page 51). The VDDIO_RMII has a minimum supply voltage requirement of 1.71V and a maximum of 3.63V; the same would hold for these pins. Table 8-2: DC Characteristics & Digital I/0 Signals Symbol Parameter/Signal Min Typ VIL VIH VIL VIH VOL VOH VIL VIH VOL VOH RPU RPD RPU

-0.5 2.0

-0.5 2.0 VCC-0.4 0.625*VCC 0.75*VCC RESET#

RESET#

CPx, UART, JTAG CPx, UART, JTAG CPx, UART, JTAG CPx, UART, JTAG SDIO pins SDIO pins SDIO pins SDIO pins SDIO_MODE/SPI_ SLAVE_MODE 39.58 44.57 44.57 Max 0.8 VCC + 0.5 0.8 VCC + 0.5 0.4 0.25*VCC 0.125*VCC Unit V V V V V V V V V V k k k xPico 200 Series Embedded Wi-Fi Gateway Data Sheet 35 Dynamic Power Management Modes The table below describes the power management modes for the xPico 200 module, along with their typical and maximum current consumption values. The xPico 200 module supports power-up and standby modes within its dynamic application-

aware power management framework. Table 8-3: xPico 200 Power Consumption 2.4 GHz (@ 3.3 V, 25o C), Bluetooth Disabled 105BParameter 106BPower Mgmt 107BSoft AP 108BTypica lxPico 240 109BTypical xPico 250/270 110BMax xPico 240 111BMax xPico 250/270 112BUnits Boot sequence peak Idle current average-unit connected to AP on client 11n Ch6 Idle current average-unit connected to AP on client 11n Ch6 Idle current average unit connected to AP on client 11n Ch6 Iperf (UDP) in bridge mode to AP on client interface 1 Mbps-Sustained 11n Ch6 Transmitter surge, 11g 54 Mbps, 15 dBm Transmitter surge, 11n, 20 MHz BW, MCS7, 17 dBm Transmitter surge, 11g 54 Mbps, 0 dBm Transmitter surge, 11n, 20 MHz BW, MCS7, 0 dBm Stand by, external IO connections removed @

+25C Stand by with external PHY, other external IO connections removed @ +25C Ethernet ping, Wi-Fi disabled. External PHY current not included N/A OFF N/A ON 580 95 600 123 ON 95 123 OFF 41 66 OFF 95 128 ON, Beacon 100 ms, DTIM 5 ON, Beacon 100 ms, DTIM 5 ON, Beacon 100 ms, DTIM 5 mA mA mA mA mA N/A N/A 345 379 399 427 mA N/A N/A 345 380 398 430 mA N/A N/A 298 328 358 383 mA N/A N/A 299 330 356 386 mA N/A N/A 30 38 N/A N/A 97 97 N/A N/A 37 37 uA uA mA xPico 200 Series Embedded Wi-Fi Gateway Data Sheet 36 Table 8-4: xPico 200 Power Consumption 5 GHz (@ 3.3 V, 25o C), Bluetooth Disabled 113BParameter 114BPower Mgmt 115BSoft AP 116BTypical xPico 240 117BTypical xPico 250/270 118BMax xPico 240 119BMax xPico 250/270 120BUnits N/A OFF N/A ON 580 148 600 174 Boot sequence peak Idle current average-unit connected to AP on client 11n Ch48 Idle current average-unit connected to AP on client 11n Ch48 Idle current average unit connected to AP on client 11n Ch48 Iperf (UDP) in bridge mode to AP on client interface 1 Mbps-

Sustained, 11n Ch48 Transmitter surge, 11a 54 Mbps, 14 dBm Transmitter surge, 11n, 40 MHz BW, MCS7, 14 dBm Transmitter surge, 11a 54 Mbps, 0 dBm Transmitter surge, 11n, 40 MHz BW, MCS7, 0 dBm Stand by, external IO connections removed @

+25 C Stand by with external PHY, other external IO connections removed @

+25 C Ethernet ping, Wi-Fi disabled. External PHY current not included mA mA mA mA mA ON 148 172 OFF 40 66 OFF 134 166 ON, Beacon 100 ms, DTIM 5 ON, Beacon 100 ms, DTIM 5 ON, Beacon 100 ms, DTIM 5 N/A N/A N/A 390 429 465 499 mA N/A 401 440 494 532 mA N/A N/A 316 350 395 457 mA N/A N/A 334 360 419 494 mA N/A N/A 30 38 N/A N/A 97 97 N/A N/A 37 37 uA uA mA xPico 200 Series Embedded Wi-Fi Gateway Data Sheet 37 Table 8-5: xPico 250/270 Power Consumption with Bluetooth Enabled (@ 3.3 V, 25oC) 121BParameter 122BPower Mgmt 123BSoft AP/

Wi-Fi Client 124BAverag e Current 125BPeak Current Typical 126BUnits BLE peripheral not connected. Wi-Fi client and Soft AP disabled BLE peripheral not connected. Wi-Fi Client connected (2.4 GHz) ping. Soft AP enabled. BLE peripheral not connected. Wi-Fi Client connected (5 GHz) ping. Soft AP enabled. BLE peripheral connected. Wi-Fi client and Soft AP disabled BLE peripheral connected. Wi-Fi Client connected (2.4 GHz) ping. Soft AP enabled. BLE peripheral connected. Wi-Fi Client connected (5 GHz) ping. Soft AP enabled. OFF Disable 44 OFF Enabled 110 OFF Enabled 124 OFF Disabled 45 OFF Enabled 112 OFF Enabled 126 120 556 600 121 556 600 mA mA mA mA mA mA Output Power The xPico 200 module RF output power is listed in the Table 8-6 below. Table 8-6: xPico 200 Module RF Output Power (Wi-Fi Conducted) 127BMode 128BRate 129BTYP. 130BTolerance 131BUnit RF Average Output Power, 802.11b RF Average Output Power, 802.11g RF Average Output Power, 802.11n (2.4 GHz) RF Average Output Power, 802.11a RF Average Output Power, 802.11n (5 GHz) RF Average Output Power, 802.11ac (5 GHz)

(xPico 270 only) 1 Mbps 11 Mbps 6 Mbps 54 Mbps MCS0 MCS7 6 Mbps 54 Mbps MCS0 MCS7 MCS9 17 17 15 15 15 15 15 15 13 13 12

+ 2

+ 2

+ 2

+ 2

+ 2

+ 2

+ 2

+ 2

+ 2

+ 2

+2 Table 8-7: xPico 200 Module RF Output Power (BT Conducted) 132BMode 133BRate 134BMin. 135BTYP. 136BMax BLE RF Average Output Power Power Class 12 Power Class 22 Power Class 32 1Max EIRP for BLE 10 dBm per BT specification 2Refer to BT Sig power transmitter power specifications BR/EDR BR/EDR BR/EDR 0

-6 61 3 20 4 0 dBm dBm dBm dBm dBm dBm dBm dBm dBm dBm dBm 137BUnit dBm dBm dBm dBm xPico 200 Series Embedded Wi-Fi Gateway Data Sheet 38 Input Power The xPico 200 module RF input power is listed in Table 8-8, Table 8-9, and Table 8-10 below. Table 8-8: xPico 200 Module RF Input Power Wi-Fi 2.4 GHz 138BMaximum RF Receive Level Absolute Maximum Wi-Fi Signal

@ 1, 2 Mbps (8% PER, 1024 octets)

@ 5.5, 11 Mbps (8% PER, 1024 octets)

@ 6, 9, 12 Mbps (10% PER, 1024 octets)

@ MCS02 rates (10% PER, 4095 octets)

@ 18, 24, 36, 48, 54 Mbps (10% PER, 1024 octets)

@ MCS37 rates (10% PER, 4095 octets) 139BMaximum 140BUnit

+5

-3.5

-9.5

-9.5

-9.5

-14.5

-14.5 dBm dBm dBm dBm dBm dBm dBm Table 8-9: xPico 200 Module RF Input Power Wi-Fi 5 GHz 141BMaximum RF Receive Level Absolute Maximum Wi-Fi Signal

@ 6, 9, 12 Mbps (10% PER, 1024 octets)

@ MCS02 rates (10% PER, 4095 octets)

@ 18, 24, 36, 48, 54 Mbps (10% PER, 1024 octets)

@ MCS39 rates (10% PER, 4095 octets) 142BMaximum 143BUnit

+5

-9.5

-9.5

-14.5

-14.5 dBm dBm dBm dBm dBm Table 8-10: xPico 200 Module RF Input Power BT 144BMaximum RF Receive Level Maximum RF Input Level CW signal Maximum RF Input (High Peak to Average, ex Wi-Fi) 145BMaximum 146BUnit

-5

-10 dBm dBm xPico 200 Series Embedded Wi-Fi Gateway Data Sheet 39 EVM The xPico 200 module TX EVM follow the IEEE specification listed in Table 8-11 below. Table 8-11: xPico 200 Module Wi-Fi EVM 147BMode RF Average Output EVM (11g) RF Average Output EVM (11n 2.4 GHz) RF Average Output EVM (11a) RF Average Output EVM (11n 5 GHz) RF Average Output EVM (11ac 5 GHz)

(xPico 270 only) 148BRate 6 Mbps 54 Mbps MCS0 MCS7 6 Mbps 54 Mbps MCS0 MCS7 MCS9 149BMax 150BUnit

-5

-25

-5

-27

-5

-25

-5

-27

-32 dB dB dB dB dB dB dB dB dB RX Sensitivity The xPico 200 module Rx sensitivity is listed in Table 8-12 below. Table 8-12: xPico 200 Module Rx Sensitivity @ 3.3 V input power, +25o C 151BReceiver Characteristics PER <10%, Rx Sensitivity @ 802.11g 6 Mbps PER <10%, Rx Sensitivity @ 802.11g 54 Mbps PER <10%, Rx Sensitivity @ 802.11a 6 Mbps PER <10%, Rx Sensitivity @ 802.11a 54 Mbps PER <10%, Rx Sensitivity @ 802.11n 5 GHz MCS7 HT20 PER <10%, Rx Sensitivity @ 802.11n 5 GHz MCS7 HT40 BER <0.1%, Rx Sensitivity @ Bluetooth BR, 1 Mbps GFSK BER <0.01%, Rx Sensitivity @ Bluetooth EDR, 3 Mbps D8PSK 152BTypical

-92.6 dBm

-75.5 dBm

-88.7 dBm

-73.7 dBm

-72.0 dBm

-68.8 dBm

-89.2 dBm

-85.6 dBm xPico 200 Series Embedded Wi-Fi Gateway Data Sheet 40 Power, Reset, Wake, Shutdown and Default Timing The diagrams below show the timing requirement for VCC, RESET#, DEFAULT#, WAKE and SHDN. Figure 8-1 Reset Timing Figure 8-2 Reset to Defaults Timing Figure 8-3 Wake Timing xPico 200 Series Embedded Wi-Fi Gateway Data Sheet 41 153BParameter 154BDescription 155BMinimum Table 8-13: Shutdown Pin Timing Tpu Tpor Treboot Tpup2dflt Tdefault Twake Teio_off Time for VCC to reach 90% of its maximum value Time from VCC to reach 90% of its maximum value and de-assertion of external reset. Recommended reset pulse for system reboot Time from VCC power up to DEFAULT#

assertion. Note DEFAULT# can be left floating if unused. Assertion time for DEFAULT# to unit reset to default and reboot. Wake pulse width. Note wakeup is triggered on the rising edge. Time recommended to shut off external IO to prevent leakage into module 40 50 50 0 6 100 0 156BMaximu m 1000 157BUnit us ms ms ns S us ms xPico 200 Series Embedded Wi-Fi Gateway Data Sheet 42 SPI Slave Timing The diagram below shows the timing requirement for SPI_CLK, SPI_DIN, and SPI_DOUT. Data is sampled on the rising edge of the clock. Figure 8-4 SPI Slave Timing Table 8-14: SPI Slave Timing 158BParameter 159BDescription 160BMinimum 161BMaximum 162BUni t T1 T2/T3 T4/T5 T6 T7 T8 T9 CSX to clock Clock to CSX Clock period. Fmax = 50 MHz. Clock high/low. Clock rise/fall time. Input setup time, SIMO valid to SPI_CLK active edge. Input hold time, SPI_CLK active edge to SIMO invalid. Output setup time, SOMI valid before SPI_CLK rising. Output hold time, SPI_CLK active edge to SOMI invalid. CSX fall to 1st rising edge. SPI_CSx remains active for the entire duration of SPI Slave read/write/write_read transaction. Last falling edge to CSX high. xPico 200 Series Embedded Wi-Fi Gateway Data Sheet 2.08

(0.45 x T1) T4

ns

(0.55 x T1) T4 ns ns 2.5 5.0 5.0 5.0 5.0 7.86

ns ns ns ns ns ns 43 SPI Master Timing The diagram below shows the timing requirement for CS, CK, SDI, and SDO. Figure 8-5 SPI Master Timing 163BParameter 164BDescription 165BMinimum 166BMaximum Table 8-15: SPI Master Timing T1 T2 T3 T4 T5 T6 Operating Voltage Frequency of operation SCK output cycle time SCK output high/low time CS Active to SCK delay SCK to CS inactive delay SCK to MOSI valid SCK to MOSI invalid 1 1/26.7MHz 18 880 756

35.6 VDDIO 26.7 13 167BUni t V MHz ns ns ns ns ns ns xPico 200 Series Embedded Wi-Fi Gateway Data Sheet 44 Memory The xPico 200 module comes with the following memory profile:

Flash Memory The xPico 200 module has 8 MB serial NOR flash that is shared between the boot, OS, and user space. SRAM The xPico 200 module has 2 MB SRAM. xPico 200 Series Embedded Wi-Fi Gateway Data Sheet 45 9. Package Description and Mechanical Footprint The xPico 200 module comes in two different mechanical packages. The first is an SMT module with an LGA footprint. The LGA footprint version is for SMT applications. The second mechanical package is the xPico 200 module mounted on an edge card. The mechanical dimensions for both options are shown below. Both mechanical packages also come with options for two U.FL connectors for connection to external antennas or a single on-module antenna. Note, Bluetooth is not available for the options with on-module antenna. Dimensions The size and thickness of the xPico 200 module is 25 mm (L) x 17 mm (W) x 2.53 mm (H) +/-

0.3 mm (including shielding). The PCB footprint is shown in Figure 9-3. Figure 9-1 xPico 200 Embedded Wi-Fi Gateway (On-Module Antenna) Figure 9-2 xPico 200 Embedded Wi-Fi Gateway (Dual U.FL) Note: Wi-Fi Diversity not available on units with Bluetooth. xPico 200 Series Embedded Wi-Fi Gateway Data Sheet 46 Figure 9-3 Layout Footprint for xPico 200 Enterprise Wi-Fi IoT Module Note:

It is recommended to follow the evaluation platform layout. Find this within the Platform PCB Package, which can be downloaded at https://www.lantronix.com/products/xpico-200/. xPico 200 Series Embedded Wi-Fi Gateway Data Sheet 47 Figure 9-4 xPico 200 Edge Connector Footprint Dimensions Note: The Edge Connector Module mates to TE Connectivity part number 2199230-4. Material and Weight 168BCategory Weight Material Table 9-1: Material and Weight 169BDescription 1.654 g (with on module antenna option), 1.552 g (with two U.FL option) Metal shell xPico 200 Series Embedded Wi-Fi Gateway Data Sheet 48 10. Product Information Label The product information label contains important information about your specific module, including the part number, revision, manufacturing date code, product model, country of origin, Datamatrix barcode, and MAC address. Figure 10-1 xPico 200 Module Label The xPico 200 module uses the Datamatrix ECC200 bar code standard. The field definitions are as follows:

Table 10-1: Datamatrix ECC200 Barcode Standard Descriptions 170BField 171BDescription V1 C1 P1 R1 D1 L1 S1 S2 E1 Barcode revision Count of tags Part number of the module Revision of the module Manufacturing date code of the module Manufacturing location/factory Serial number ConsoleFlow Device ID End of barcode 172BExample 4 3 950-00101 A11 14W20 CHINA 01 0080A3980404 AAAABBBBCCCCDDDDEEEEFFFFGGGGHHHH xPico 200 Series Embedded Wi-Fi Gateway Data Sheet 49 11. Compliance

(According to ISO/IEC Guide and EN 45014) Manufacturer's Name & Address:

Lantronix, Inc., 48 Discovery, Suite 250, Irvine, CA 92618 USA Declares that the following product:

Product Name Model: xPico 200 Conforms to the following standards or other normative documents:

Table 11-1: Country Certifications (xPico 240/250/270) Country Specification USA Canada EU UK Australia, New Zealand N11206 Japan FCC Part 15,Subpart B, Class B FCC Part 15, Subpart C 15.247 (WLAN) FCC Part 15, Subpart C 15.247 (BT) FCC Part 15, Supbart E 15.407 (DFS) ICES-003:2012 Issue 5, Class B RSS-Gen, Issue 4, 2014-11 RSS-102, Issue 5, 2015-03 RSS-247, Issue 2, 2017-02 xPico 240 xPico 250 xPico 270 Yes Yes Yes Yes Yes Yes See EU Declaration of Conformity below. Yes Yes Yes See UK Declaration of Conformity below. Yes Yes Yes AS/NZS 4268 2017 AS/NZS 2772.2 Yes Yes Yes ARIB STD-T66(v3.7), MIC notice 88 Appendix 43 ARIB STD-T71(v6.1), MIC notice 88 Appendix 45 Yes Yes Yes China SRRC India Taiwan Mexico Safety WPC ETA LP002 NOM, IFETEL EN 62368-1 Yes Yes Yes

Yes Yes Yes Yes Yes Yes Yes Yes Yes

**For additional regional certification requests please contact your local Lantronix sales team member. xPico 200 Series Embedded Wi-Fi Gateway Data Sheet 50 Labeling of the End Product The label on the end product incorporating the xPico 200 gateway must clearly state that it contains an FCC-approved RF module. Canada and Japan also require a similar statement. For example, This product contains RF transmitter ID # (put FCC, IC, CMIIT, and/or Japan module grant numbers here). The label must include the ID numbers for the regions where the end product is installed. The grant numbers are below. Table 11-2: Country Transmitter IDs (xPico 240) Country USA FCC ID Canada IC ID Japan ID China SRRC India ID Taiwan ID Mexico ID Country USA FCC ID Canada IC ID Japan ID China SRRC India ID Taiwan ID Mexico ID Country USA FCC ID Canada IC ID Japan ID China SRRC India ID Taiwan ID Mexico ID Specification R68XPICO200 3867A-XPICO200 020-170133 2017AJ6663(M)

**Contact Lantronix Sales

**Contact Lantronix Sales

**Contact Lantronix Sales Table 11-3: Country Transmitter IDs (xPico 250) Specification R68XPICO200 3867A-XPICO200 020-170133 2017AJ6665(M) ETA-SD-20190501074 CCAJ19LP6150T9 RCPLAXP19-1127 Table 11-4: Country Transmitter IDs (xPico 270) Specification R68XPICO200 3867A-XPICO200 201-200880 2021AJ0636(M) ETA-SD-20190601953 CCAJ19LP6151T1 RCPLAXP19-1125

**For additional regional certification requests please contact your local Lantronix sales team member. xPico 200 Series Embedded Wi-Fi Gateway Data Sheet 51 Federal Communication Commission Interference Statement (xPico 240/250/270) This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Operations in the 5.15-5.25 GHz band are restricted to indoor usage only. Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. This device is intended only for OEM integrators under the following conditions:

1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and 2) The transmitter module may not be co-located with any other transmitter or antenna. As long as 2 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed. IMPORTANT NOTE: In the event that these conditions cannot be met (for example certain laptop configurations or colocation with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID cannot be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization. End Product Labeling This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm may be maintained between the antenna and users. The final end product must xPico 200 Series Embedded Wi-Fi Gateway Data Sheet 52 be labeled in a visible area with the following: Contains FCC ID: R68XPICO200. The grantee's FCC ID can be used only when all FCC compliance requirements are met. Manual Information to the End User The OEM integrator must not provide information to the end user regarding how to install or remove this RF module in the users manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual. Industry Canada Statement (xPico 240/250/270):

This device complies with RSS-247 of the Industry Canada Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Ce dispositif est conforme la norme CNR-247 d'Industrie Canada applicable aux appareils radio exempts de licence. Son fonctionnement est sujet aux deux conditions suivantes: (1) le dispositif ne doit pas produire de brouillage prjudiciable, et (2) ce dispositif doit accepter tout brouillage reu, y compris un brouillage susceptible de provoquer un fonctionnement indsirable. Radiation Exposure Statement:

This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Dclaration d'exposition aux radiations:

Cet quipement est conforme aux limites d'exposition aux rayonnements IC tablies pour un environnement non contrl. Cet quipement doit tre install et utilis avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps. This device is intended only for OEM integrators under the following conditions:

(For module device use) 1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and 2) The transmitter module may not be co-located with any other transmitter or antenna. As long as 2 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed. Cet appareil est conu uniquement pour les intgrateurs OEM dans les conditions suivantes: (Pour utilisation de dispositive module) 1) L'antenne doit tre installe de telle sorte qu'une distance de 20 cm est respecte entre l'antenne et les utilisateurs, et 2) Le module metteur peut ne pas tre complant avec un autre metteur ou antenne. xPico 200 Series Embedded Wi-Fi Gateway Data Sheet 53 Tant que les 2 conditions ci-dessus sont remplies, des essais supplmentaires sur l'metteur ne seront pas ncessaires. Toutefois, l'intgrateur OEM est toujours responsable des essais sur son produit final pour toutes exigences de conformit supplmentaires requis pour ce module install. IMPORTANT NOTE:

In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the Canada authorization is no longer considered valid and the IC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product

(including the transmitter) and obtaining a separate Canada authorization. NOTE IMPORTANTE:

Dans le cas o ces conditions ne peuvent tre satisfaites (par exemple pour certaines configurations d'ordinateur portable ou de certaines co-localisation avec un autre metteur), l'autorisation du Canada n'est plus considr comme valide et l'ID IC ne peut pas tre utilis sur le produit final. Dans ces circonstances, l'intgrateur OEM sera charg de rvaluer le produit final (y compris l'metteur) et l'obtention d'une autorisation distincte au Canada. Plaque signaltique du produit final Ce module metteur est autoris uniquement pour une utilisation dans un dispositif o l'antenne peut tre installe de telle sorte qu'une distance de 20cm peut tre maintenue entre l'antenne et les utilisateurs. Le produit final doit tre tiquet dans un endroit visible avec l'inscription suivante: "Contient des IC: 3867A-XPICO200". Manual Information To the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the users manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual. Manuel d'information l'utilisateur final L'intgrateur OEM doit tre conscient de ne pas fournir des informations l'utilisateur final quant la faon d'installer ou de supprimer ce module RF dans le manuel de l'utilisateur du produit final qui intgre ce module. Le manuel de l'utilisateur final doit inclure toutes les informations rglementaires requises et avertissements comme indiqu dans ce manuel. Caution :

(i) the device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to cochannel mobile satellite systems;

(ii) the maximum antenna gain permitted for devices in the bands 5250-5350 MHz and 5470-5725 MHz shall be such that the equipment still complies with the e.i.r.p. limit;

(iii) the maximum antenna gain permitted for devices in the band 5725-5850 MHz shall be such that the equipment still complies with the e.i.r.p. limits specified for point-to-point and non-point-to-point operation as appropriate; and xPico 200 Series Embedded Wi-Fi Gateway Data Sheet 54

(iv) Users should also be advised that high-power radars are allocated as primary users

(i.e. priority users) of the bands 5250-5350 MHz and 5650-5850 MHz and that these radars could cause interference and/or damage to LE-LAN devices. Avertissement :

Le guide dutilisation des dispositifs pour rseaux locaux doit inclure des instructions prcises sur les restrictions susmentionnes, notamment :

(i) les dispositifs fonctionnant dans la bande 5150-5250 MHz sont rservs uniquement pour une utilisation lintrieur afin de rduire les risques de brouillage prjudiciable aux systmes de satellites mobiles utilisant les mmes canaux;

(ii) le gain maximal d'antenne permis pour les dispositifs utilisant les bandes de 5250 5 350 MHz et de 5470 5725 MHz doit tre conforme la limite de la p.i.r.e;

(iii) le gain maximal d'antenne permis (pour les dispositifs utilisant la bande de 5 725 5 850 MHz) doit tre conforme la limite de la p.i.r.e. spcifie pour l'exploitation point point et lexploitation non point point, selon le cas;

(iv) De plus, les utilisateurs devraient aussi tre aviss que les utilisateurs de radars de haute puissance sont dsigns utilisateurs principaux (c.--d., quils ont la priorit) pour les bandes 5250-5350 MHz et 5650-5850 MHz et que ces radars pourraient causer du brouillage et/ou des dommages aux dispositifs LAN-EL. xPico 200 Series Embedded Wi-Fi Gateway Data Sheet 55 Figure 11-12 EU Declaration of Conformity (xPico 240 / xPico 250 / xPico 270) xPico 200 Series Embedded Wi-Fi Gateway Data Sheet 56 Figure 11-23 UK Declaration of Conformity (xPico 240 / xPico 250 / xPico 270) xPico 200 Series Embedded Wi-Fi Gateway Data Sheet 57 Table 11-5: Europe EU Declaration of Conformity (xPico 240/250/270) cs esky [Czech]

Lantronix tmto prohlauje, e tento xPico 200 je ve shod se zkladnmi poadavky a dalmi pslunmi ustanovenmi smrnice 2014/53/EU. da Dansk [Danish]

Undertegnede Lantronix erklrer herved, at flgende udstyr xPico 200 overholder de vsentlige krav og vrige relevante krav i direktiv 2014/53/EU. de Deutsch [German]

Hiermit erklrt Lantronix, dass sich das Gert xPico 200 in bereinstimmung mit den grundlegenden Anforderungen und den brigen einschlgigen Bestimmungen der Richtlinie 2014/53/EU befindet. et Eesti [Estonian]

Kesolevaga kinnitab Lantronix seadme xPico 200 vastavust direktiivi 2014/53/EU phinuetele ja nimetatud direktiivist tulenevatele teistele asjakohastele stetele. en English Hereby, Lantronix, declares that this xPico 200 is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. es Espaol [Spanish]

Por medio de la presente Lantronix declara que el xPico 200 module cumple con los requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 2014/53/EU. el

[Greek]

Lantronix xPico 200 2014/53/EU. fr Franais [French]

Par la prsente Lantronix dclare que l'appareil xPico 200 est conforme aux exigences essentielles et aux autres dispositions pertinentes de la directive 2014/53/EU. it Italiano [Italian]

Con la presente Lantronix dichiara che questo xPico 200 conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 2014/53/EU. Latviski [Latvian]

Ar o Lantronix deklar, ka xPico 200 atbilst Direktvas 2014/53/EU btiskajm prasbm un citiem ar to saisttajiem noteikumiem. Lietuvi [Lithuanian]

iuo Lantronix deklaruoja, kad is xPico 200 atitinka esminius reikalavimus ir kitas 2014/53/EU Direktyvos nuostatas. nl Nederlands [Dutch]

Hierbij verklaart Lantronix dat het toestel xPico 200 overeenstemming is met de essentile eisen en de andere relevante bepalingen van richtlijn 2014/53/EU. mt Malti [Maltese]

Hawnhekk, Lantronix, jiddikjara li dan xPico 200 jikkonforma maltiijiet essenzjali u ma provvedimenti orajn relevanti li hemm fid-Dirrettiva 2014/53/EU. hu Magyar [Hungarian]

Alulrott, Lantronix nyilatkozom, hogy a xPico 200 megfelel a vonatkoz alapvet kvetelmnyeknek s az 2014/53/EU irnyelv egyb elrsainak. pl Polski [Polish]

pt sl Portugus

[Portuguese]

Slovensko

[Slovenian]

Niniejszym Lantronix owiadcza, e xPico 200 jest zgodny z zasadniczymi wymogami oraz pozostaymi stosownymi postanowieniami Dyrektywy 2014/53/EU. Lantronix declara que este xPico 200 est conforme com os requisitos essenciais e outras disposies da Directiva 2014/53/EU. Lantronix izjavlja, da je ta xPico 200 v skladu z bistvenimi zahtevami in ostalimi relevantnimi doloili direktive 2014/53/EU. Slovensky [Slovak]

Lantronix tmto vyhlasuje, e xPico 200 enterprise Wi-Fi IoT module spa zkladn poiadavky a vetky prslun ustanovenia Smernice 2014/53/EU. fi Suomi [Finnish]

Lantronix vakuuttaa tten ett xPico 200 tyyppinen laite on direktiivin 2014/53/EU oleellisten vaatimusten ja sit koskevien direktiivin muiden ehtojen mukainen. sv Svenska [Swedish]

Hrmed intygar Lantronix att denna xPico 200 str I verensstmmelse med de vsentliga egenskapskrav och vriga relevanta bestmmelser som framgr av direktiv 2014/53/EU. NB no. https://eur-lex.europa.eu/legal-content/EN/TXT/?uri=CELEX%3A32014L0053 xPico 200 Series Embedded Wi-Fi Gateway Data Sheet 58 RoHS, REACH, and WEEE Compliance Statement Please visit https://www.lantronix.com/legal/rohs/ for Lantronixs statement about RoHS, REACH and WEEE compliance. xPico 200 Series Embedded Wi-Fi Gateway Data Sheet 59 12. Ordering Information Table 12-1: xPico 240 Order Information 173BPart Number 174BDescription XPC240100B-02 XPC240200B-02 XPC240300B-02 XPC240400B-02 XPC240100S-02 XPC240200S-02 XPC240300S-02 XPC240400S-02 xPico 240 Embedded IoT Gateway, 802.11 a/b/g/n, Ethernet, Dual U.FL, Ind Temp, LGA T&R 250 xPico 240 Embedded IoT Gateway, 802.11 a/b/g/n, Ethernet, On-Module Ant, Ind Temp, LGA T&R 250 xPico 240 Embedded IoT Gateway, 802.11 a/b/g/n, Ethernet, Dual U.FL, Ind Temp, Edge Conn, Tray xPico 240 Embedded IoT Gateway, 802.11 a/b/g/n, Ethernet, On-Module Ant, Ind Temp, Edge Conn, Tray xPico 240 Embedded IoT Gateway, 802.11 a/b/g/n, Ethernet, Dual U.FL, Ind Temp, LGA T&R 25 xPico 240 Embedded IoT Gateway, 802.11 a/b/g/n, Ethernet, On-Module Ant, Ind Temp, LGA T&R 25 xPico 240 Embedded IoT Gateway, 802.11 a/b/g/n, Ethernet, Dual U.FL, Ind Temp, Edge Conn, Single xPico 240 Embedded IoT Gateway, 802.11 a/b/g/n, Ethernet, On-Module Ant, Ind Temp, Edge Conn, Single XPC240300EK XPC240400EK xPico 240 Evaluation Kit with Edge Connector Module, Dual U.FL Antenna xPico 240 Evaluation Kit with Edge Connector Module, On-Module Antenna Table 12-2: xPico 250 Order Information 175BPart Number 176BDescription XPC250100B-02 XPC250300B-02 XPC250100S-02 XPC250300S-02 xPico 250 Embedded IoT Gateway, 802.11 a/b/g/n, Ethernet, BT 4.2, Dual U.FL, Ind Temp, LGA T&R 250 xPico 250 Embedded IoT Gateway, 802.11 a/b/g/n, Ethernet, BT 4.2, Dual U.FL, Ind Temp, Edge Conn, Tray xPico 250 Embedded IoT Gateway, 802.11 a/b/g/n, Ethernet, BT 4.2, Dual U.FL, Ind Temp, LGA T&R 25 xPico 250 Embedded IoT Gateway, 802.11 a/b/g/n, Ethernet, BT 4.2, Dual U.FL, Ind Temp, Edge Conn, Single XPC250300EK xPico 250 Evaluation Kit with Edge Connector Module Table 12-3: xPico 270 Order Information 177BPart Number 178BDescription XPC270100B XPC270300B XPC270100S XPC270300S xPico 270 Embedded IoT Gateway, 802.11 ac/a/b/g/n, Ethernet, BT 4.2, Dual U.FL, Ind Temp, LGA T&R 250 xPico 270 Embedded IoT Gateway, 802.11 ac/a/b/g/n, Ethernet, BT 4.2, Dual U.FL, Ind Temp, Edge Conn, Tray xPico 270 Embedded IoT Gateway, 802.11 ac/a/b/g/n, Ethernet, BT 4.2, Dual U.FL, Ind Temp, LGA T&R 25 xPico 270 Embedded IoT Gateway, 802.11 ac/a/b/g/n, Ethernet, BT 4.2, Dual U.FL, Ind Temp, Edge Conn, Single XPC270300EK xPico 270 Evaluation Kit with Edge Connector Module xPico 200 Series Embedded Wi-Fi Gateway Data Sheet 60 Warranty The xPico 200 module comes with an industry best 5-year warranty. For more details on the Lantronix warranty replacement policy, please go to our web site at http://https/www.lantronix.com/technical-support/warranty/. Contact Information For details contact your local Lantronix representative or Lantronix directly:

Asia Pacific Region via e-mail at asiapacific_sales@lantronix.com Europe via e-mail at eu_sales@lantronix.com Japan via e-mail at japan_sales@lantronix.com United States via e-mail at sales@lantronix.com or call OEM sales support at 800-526-8764. Manufacturer's Contact Lantronix, Inc. 48 Discovery, Suite 250 Irvine, CA 92618 USA Tel: 949-453-3990 Fax: 949-453-3995 2023 Lantronix, Inc. All rights reserved. Lantronix, ConsoleFlow and xPico are registered trademarks of Lantronix, Inc. in the United States and other countries. Patented: https://patents.lantronix.com/; additional patents pending. xPico 200 Series Embedded Wi-Fi Gateway Data Sheet 61

 

 

 

 

 

 

 

 

 

 

handheld SP500X S/N: SP51C90001 MAC ID: O080A3CD6B06 Product No: SP500X KC bs Regulatory Model Number: SP500X 4.5V/~1.5Amp ( @

Contains FCC ID: R68XPICO200 IC ID: 3867A-XPICO200 Complies with Canada ICES-003(A) / NMB-003 (A), Class A PRODUCT OF TAIWAN

 

 

 

 

 

 

Certification Application Attestation Statements Date: August 30, 2023 American Certification Body, Inc. 313 Park Avenue Suite 300 Falls Church, VA 22046 To Whom It May Concern:

Statement for 47 CFR section 2.911(d)(5)(i) Lantronix, Inc. (the applicant) certifies that as of the date of the application the equipment for which authorization is sought is not covered equipment1 prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. If the equipment for which the applicant seeks authorization is produced by any of the entities identified on the current Covered List, including affiliates or subsidiaries of the named companies, the applicant must include an explanation on why the equipment is not covered equipment. Additional Explanation: <N/A>

Statement for 47 CFR section 2.911(d)(5)(ii) Lantronix, Inc. (the applicant) certifies that, as of the date of the filing of this application, the applicant - is

/ - is not Identified on the Covered List (as a specifically named entity or any of its subsidiaries or affiliates) as an entity producing covered equipment. Thank you, By:

(Signature2) ________ Eric Bass__________

(Print name) Company: _ Lantronix, Inc. Telephone: _ _ +1 (949) 453-3990 _ 1 - The Commissions Covered List is published by the Public Safety and Homeland Security Bureau and posted on the Commissions website. This Covered List, which is periodically updated, identifies particular equipment, produced by particular entities, that constitutes covered equipment. https://www.fcc.gov/supplychain/coveredlist . 2 - Letters must be placed on appropriate letterhead. 050523-17 rev 8

 

 

Declaration of Authorization We Name:

Address:

City:

State/ Zip Code:

Country:

Lantronix, Inc. 48 Discovery, Suite 250 Irvine California 92618 USA Declare that:

Name Representative of agent:

Agent Company name:

Address:

City:

Country Stanley Wu (1) DEKRA Testing and Certification Co., Ltd. No. 26, Huaya 1st Road, Guishan District, Taoyuan City 33341 Taiwan is authorized to apply for FCC Certification of the following product(s):

Product description: xPico 200 Series Wi-Fi IoT Gateway Module Type designation:

Brand:

FCC ID:

xPico 270 LANTRONIX R68XPICO200 on our behalf. Date:

City:

Name:

August 30, 2023 Irvine Eric Bass (2) Function:

VP of Engineering Signature:

. Notes:

(1): Required for FCC application

(2): For FCC it must be the Grantee Code owner or the authorized agent.

 

 

DeclarationofProductModifications November10,2023 ThisistorequestaClassIIpermissivechangeforFCCID:R68XPICO200,originallygranted on06/28/2019. Themajorchangefiledunderthisapplicationis:

#1:Thetransmitterinoriginalapplicationwascettifiedwithbelowantennas:

AntSet. 1 Antennatype Dipole AntennaGain(dBi) 2.8 Frequencyrange(GHz) 2.4~2.4835 2 3 4 Dipole PCB Metal 3.8 1 0.3 2.5 5 2.5 5 5.15~5.85 2.4~2.4835 5.15~5.85 2.4~2.4835 5.15~5.85 2.4~2.4835 5.15~5.85 ThisclassIIchangeistoaddhigher3dBiChipantennaforBT,higher4dBi/5.2dBiPIFA antennasfor2.4GHz/5GHz.

#2:ReducetheBT&WLAN2.4GHz/5GHzoutputpowerthroughfirmware(SWversion:5.4). Exceptfortheabovedifferences,thehardwaredesignisidenticalwiththeoriginalgrant. Shouldyouhaveanyenquiresorcomments,pleasehavemybestattention. Sincerely, Name:EricBass Title:VPofEngineering Companyname:Lantronix,Inc.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

U.S. Agent Designation for Service of Process TO:

American Certification Body, Inc. 313 Park Avenue Suite 300 Falls Church, VA 22046 ATTENTION: FCC Certification Section 2.911(d)(7) Information This letter is to confirm that the Applicant will also serve as the U.S. Agent for Service of Process as required by 47 CFR 2.911(d)(7). The Applicant acknowledges that they must maintain an agent for no less than one year after terminating all marketing and importation OR the conclusion of any Commission-related proceeding involving the equipment. The Applicant further acknowledges their responsibility to inform the FCC whenever the Designated U.S. Agent information changes. Applicant Company name: Lantronix, Inc. FRN #: 0010978799 Grantee Code: R68 Contact Name: Eric Bass Street Address: 48 Discovery, Suite 250 City/Province/Zip: Irvine, California 92618 Telephone No: 949-4537124 Email: ebass@lantronix.com Applicant Signature1:

Date: August 30, 2023 Signed by (Printed Name/Title): Eric Bass/ VP of Engineering 1 - Letters must be placed on appropriate letterhead. The signee for the applicant must be one of the following: Applicant (grantee) contact of record in the FCCs authorization system, or authorized officers or employee of the applicant (grantee).

 

 

 

 

 

 

Request for Confidentiality Date: August 30, 2023 Subject: Confidentiality Request for: FCC ID: R68XPICO200 / IC: 3867A-XPICO200 Pursuant to FCC 47 CFR 0.457(d) and 0.459 and/or IC RSP-100, Section 12.4, the applicant requests that a part of the subject application(s) be held confidential. Type of Confidentiality Requested Short Term Short Term Short Term Short Term Short Term Short Term Short Term Short Term Short Term Permanent

Permanent *1 Permanent Permanent Permanent Permanent

Permanent *1 Exhibit Block Diagrams External Photos Internal Photos Operation Description/Theory of Operation Parts List & Placement/BOM Tune-Up Procedure Schematics Test Setup Photos Users Manual Lantronix, Inc. has spent substantial effort in developing this product and it is one of the first of its kind in industry. Having the subject information easily available to "competition" would negate the advantage they have achieved by developing this product. Not protecting the details of the design will result in financial hardship. Permanent Confidentiality:

The applicant requests the exhibits listed above as permanently confidential be permanently withheld from public review due to materials that contain trade secrets and proprietary information not customarily released to the public. Short-Term Confidentiality for FCC Applications:

The applicant requests the exhibits selected above as short term confidential be withheld from public view for a period of 180 days from the date of the Grant of Equipment Authorization and prior to marketing. This is to avoid premature release of sensitive information prior to marketing or release of the product to the public. Applicant is also aware that they are responsible to notify ACB in the event information regarding the product or the product is made available to the public before the requested period has expired. ACB will then release the documents listed above for public disclosure pursuant to FCC Public Notice DA 04-1705. Sincerely, By:

__ Eric Bass _/ VP of Engineering ___

(Signature/Title2)

(Print name) 1 - The asterisked items (*) require further information to be provided to ACB before permanent confidentiality will be extended to these exhibits. Please refer to FCC KDB 726920 and the specific Document link for D01 found at: https://apps.fcc.gov/oetcf/kdb/forms/FTSSearchResultPage.cfm?switch=P&id=41731 and review section II, 3) regarding specific information that must accompany these requests. 2 - Must be signed by applicant contact given for applicant on the FCC site, or by the authorized agent if an appropriate authorized agent letter has been provided. Letters should be placed on appropriate letterhead. 050222-17

 

 

 

 

 

 

 

 

 

 

 

 

 

 

January 6, 2021 Federal Communications Commission Office of Engineering and Technology Laboratory Division 7435 Oakland Mills Road Columbia, MD 21046-1609 SUBJECT: Class II Permissive Change for FCC ID: R68XPICO200 The product identified as FCC ID: R68XPICO200, was granted by FCC on October 27, 2017.The intention of this application is to enable the modular certified FCC ID: R68XPICO200 to be integrated in Handheld Groups Wireless Hand Reader SP500X. The module installed into host platform mentioned above is electronically and mechanically identical to the original certified module. The Original FCC testing on module under FCC ID: R68XPICO200 was performed with an antenna of higher gain, and the antenna was connected to the module in an open environment. The current host platform under application uses an antenna with lower gain and is installed inside the host platform enclosure. The physical restraints introduced by the host platform should have resulted in equal or lower level of radiated emission. Regards, LANTRONIX, INC. Fathi Hakam Vice President, Engineering

 

 

January 6, 2021 AUTHORIZATION LETTER FCC ID: R68XPICO200 IC ID: 3867A-XPICO200 To Whom It May Concern:

REFERENCE Lantronix, Inc. hereby authorizes Praveen Rao, Technical Director of C-PRAV Certification Services Australia, to act on its behalf in all matters relating to the Federal Communications Commission (FCC) and Innovation, Science and Economic Development Canada (ISED) applications for equipment authorization in connection with the FCC ID and IC/ISED ID listed above, including signing of all documents relating to these matters. Any and all acts carried out by Praveen Rao of C-PRAV Certification Services, Australia on our behalf, within the scope of the powers granted herein, shall have the same effects as acts of its own. Regards, LANTRONIX, INC. Fathi Hakam Vice President, Engineering

 

 

 

 

 

 

 

 

 

 

LANTRONIX MODEL: xPico 270 = xPico 250, xPico 240

[@CCAT se00000000 |

XXMAA Yue ddddd-0S6

5 5 m 2 o

2 5 Ez E E EE E E E F FCC ID: R68XPICO200 IC: 3867A-XPICO200