FCC ID: 2AP9E-07183100 Satellite communications system

User & Installation Manual LT-3100 Satellite Communications System Document Number: 95-100765 Rev. 1.04 Release date: November 5, 2018 Copyright Lars Thrane A/S Denmark ALL RIGHTS RESERVED LT-3100 User & Installation Manual Rev. 1.04 This Document is of copyright to Lars Thrane A/S. It contains proprietary information, which is disclosed for information purposes only. The contents of this document shall not in whole or in part be used for any other purpose without prior permission from Lars Thrane A/S. Disclaimer Any responsibility or liability for loss or damage in connection with the use of this product and the accompanying documentation is disclaimed by Lars Thrane A/S. The information in this manual is provided for information purposes only, is subject to change without notice, and may contain errors or inaccuracies. Manuals issued by Lars Thrane A/S are periodically revised and updated. Anyone relying on this information should acquire the most current version e.g. from Lars Thrane A/S. Lars Thrane A/S is not responsible for the content or accuracy of any translations or reproductions, in whole or in part, of this manual from any other source. Copyright 2018 Lars Thrane A/S. All rights reserved. Disposal Old electrical and electronic equipment marked with this symbol can contain substances hazardous to human beings and the environment. Never dispose these items together with unsorted municipal waste

(household waste). In order to protect the environment and ensure the correct recycling of old equipment as well as the re-utilization of individual components, use either public collection or private collection by the local distributor of old electrical and electronic equipment marked with this symbol. Contact the local distributor or dealer for information about what type of return system to use. IMO and SOLAS The equipment described in this manual is intended for use on commercial marine and leisure vessels. The equipment is not covered by the International Maritime Organization (IMO) and Safety of Life at Sea

(SOLAS) regulations. Lars Thrane A/S www.thrane.eu i LT-3100 User & Installation Manual Rev. 1.04 Safety Instructions for Installer & Operator The following safety instructions must be observed during all phases of operation, installation, service and repair of this equipment. Failure to comply with these precautions or with specific warnings elsewhere in this manual violates safety standards of design, manufacture and intended use of the equipment. Lars Thrane A/S assumes no liability for the customer's failure to comply with these requirements. Instructions for the Installer Instructions for the Operator WARNING - Product installation WARNING Do not disassemble To ensure correct performance of this equipment, it is strongly recommended that professionals with expertise, properly trained, and likewise authorized within the industry is completing the installation. WARNING Turn off power switch Turn off the main power switch before installing the equipment described in this manual. Do not connect or disconnect equipment when the main power switch is on. Do not disassemble or modify this equipment. Fire, electrical shock, or serious injury can result. WARNING Keep away from live circuits Operational personnel must not remove product enclosure. Do not service the equipment with the communication cable connected. Always disconnect and discharge unit, cable and circuits before touching them. WARNING Use only the supplied cable WARNING - Permanent watch Use only the supplied power and communication cable for connecting the equipment. WARNING Input Power The input voltage range is: 10-32 VDC. WARNING Power supply protection Make sure that the power supply is adequately protected by a fuse or an automatic circuit breaker when installing the equipment (max. 7.5 A). In case of smoke or water leaks into the equipment, immediately turn off the power. Continued use of the equipment can cause fire or electrical shock. Keep access and permanent watch of the equipment in order to prevent any unwanted escalation. WARNING DC mains connector The DC mains connector is to be used as the disconnection device to isolate the equipment from the mains supply. WARNING - Explosive atmosphere Do not operate the equipment in the presence of flammable gases or fumes. Operation of any electrical equipment in such an environment constitutes a definite hazard. WARNING - Compass safe distance The compass safe distance for standard and steering compasses is 0.85 m (2.8 ft) and 0.65 m

(2.1 ft) respectively. Observe these distances to prevent interference to a magnetic compass. IMPORTANT - Safety distance The safety distance from the LT-3130 Antenna Unit, when the LT-3130 Antenna Unit is powered and transmitting, is 0.1 m (0.3 ft), in order to comply with the regional regulations. Always keep this safety distance to the LT-3130 Antenna Unit to avoid any serious injury. If the safety precautions and warnings on this site are not followed, warranty will be void. Lars Thrane A/S www.thrane.eu ii LT-3100 User & Installation Manual Rev. 1.04 IMPORTANT FCC Compliance Note:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and the receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help. This product does not contain any user-serviceable parts. Repairs should only be made by an authorized Lars Thrane A/S service center. Unauthorized repairs or modifications could result in permanent damage to the equipment and void your warranty and your authority to operate this device under Part 15 regulations. IMPORTANT Innovation, Science and Economic Development Canada Compliance Note:

This device complies with Innovation, Science and Economic Development Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Required information for the reader Throughout this document, essential information will be presented to the reader. The following text

(emphasized) has the following meaning and/or implication:

WARNING: A Warning is an Operation or Service procedure that, if not avoided, may cause a hazard situation, which could result in personnel death or serious injury. IMPORTANT: Text marked Important provides essential information to the reader, and is key information to the user in order for the equipment to work properly. Damage to the equipment can occur if instructions are not followed. NOTE:

A Note provides essential information to the reader. Lars Thrane A/S www.thrane.eu iii LT-3100 User & Installation Manual Rev. 1.04 About this manual Intended readers This is a User & Installation Manual for LT-3100 Satellite Communications System, or LT-3100 system. The manual is primarily intended for installers and service personnel. Personnel installing or servicing the system should be professionals with technical expertise, properly trained, and likewise authorized. All safety instructions and guidelines in this manual must be observed. The safety instructions are listed in the beginning of the manual. The guidelines are to be found in the separate chapters, where it is needed. Lars Thrane A/S www.thrane.eu iv LT-3100 User & Installation Manual Rev. 1.04 Software versions This manual is applicable to the following software:

Software Versions Description LT-3100 system Table 1: Software Versions Version 1.01 Lars Thrane A/S www.thrane.eu v LT-3100 User & Installation Manual Rev. 1.04 Record of Revisions Rev. Description Release Date Initials 1.00 1.01 1.02 1.03 1.04 Original document. January 12, 2018 Document updated with editorial corrections. January 17, 2018 As a result of the certification completed, the following sections are updated:

Safety Instructions for Installer & Operator App. A - Specifications As a result of the certification process, the following sections are updated:

Safety Instructions for Installer & Operator As a result of the FCC certification process, the following sections are updated:

Safety Instructions for Installer & Operator May 29, 2018 July 13, 2018 PT PT PT CT November 5, 2018 CT Lars Thrane A/S www.thrane.eu vi LT-3100 User & Installation Manual Rev. 1.04 Table of Contents Introduction ...................................................................................................................................................... 1 Unpacking (in-the-box) ..................................................................................................................................... 2 Inspection ...................................................................................................................................................... 2 Accessories ........................................................................................................................................................ 3 Mounts .......................................................................................................................................................... 3 Cable and connectors ................................................................................................................................... 3 System Overview .............................................................................................................................................. 4 Installation and Mounting ................................................................................................................................ 5 LT-3110 Control Unit ..................................................................................................................................... 5 LT-3120 Handset ........................................................................................................................................... 8 LT-3121 Cradle............................................................................................................................................... 9 LT-3130 Antenna Unit ................................................................................................................................. 10 Bracket Mount, Antenna Unit .................................................................................................................... 13 Pole Mount, Antenna Unit ......................................................................................................................... 15 Interfaces......................................................................................................................................................... 17 DC input ....................................................................................................................................................... 17 Chassis ground ............................................................................................................................................ 17 SIM card ...................................................................................................................................................... 17 Ethernet (RJ45) ............................................................................................................................................ 19 Auxiliary ...................................................................................................................................................... 19 Antenna ....................................................................................................................................................... 20 User Interface (UI)........................................................................................................................................... 22 Menu ........................................................................................................................................................... 23 System information .................................................................................................................................... 24 Make a voice call ......................................................................................................................................... 27 Web server ...................................................................................................................................................... 30 Dashboard ................................................................................................................................................... 31 Software update ......................................................................................................................................... 31 Diagnostic report ........................................................................................................................................ 31 Accessing the built-in web server ............................................................................................................... 32 Service & Repair .............................................................................................................................................. 33 Appendixes ...................................................................................................................................................... 34 App. A - Specifications ................................................................................................................................ 34 Lars Thrane A/S www.thrane.eu vii LT-3100 User & Installation Manual Rev. 1.04 App. B - Outline Drawing: LT-3110 Control Unit ........................................................................................ 35 App. C - Outline Drawing: Bracket Mount, Control Unit ........................................................................... 36 App. D - Outline Drawing: Flush Mount, Control Unit ............................................................................... 37 App. E - Outline Drawing: LT-3130 Antenna Unit ...................................................................................... 38 App. F - Outline Drawing: Pole Mount, Antenna Unit ............................................................................... 39 App. G - Outline Drawing: Bracket Mount, Antenna Unit ......................................................................... 40 App. H - Outline Drawing: LT-3120 Handset .............................................................................................. 41 App. I - Outline Drawing: LT-3121 Cradle ................................................................................................... 42 Lars Thrane A/S www.thrane.eu viii LT-3100 User & Installation Manual Rev. 1.04 Introduction Introduction Congratulations on your purchase of the LT-3100 Satellite Communications system!

The LT-3100 Satellite Communications System is a maritime satellite communication product from Lars Thrane A/S. The LT-3100 system is designed for the professional market (deep sea, fishing, and workboats), but can be used for the leisure market as well. The LT-3100 system meets all standards and certification requirements needed for worldwide maritime satellite communication equipment. The LT-3100 system has voice and data capabilities with 100% global coverage provided by the Iridium Communications Network. The LT-3100 system consists of a control unit, antenna unit, handset and cradle. A single coaxial cable connects the control unit with the antenna unit. Using a standard coaxial cable, up to 500 meters of separation between the units can be obtained, giving freedom to mount the antenna unit in the best possible location, with free line of sight to the satellites. The LT-3100 system can be used as the primary satellite communication product on vessels, covering the basic communication needs in terms of connectivity between the ship and shore. Lars Thrane A/S www.thrane.eu Page 1 of 42 LT-3100 User & Installation Manual Rev. 1.04 Unpacking (in-the-box) Unpacking (in-the-box) Unpack the LT-3100 Satellite Communications System Basic (P/N: 90-101142) and check that the following items are present in the box:

51-100987 LT-3110 Control Unit 51-100988 LT-3120 Handset 51-101181 LT-3121 Cradle 51-100989 LT-3130 Antenna Unit 91-100771 Bracket Mount, Control Unit 91-100767 Power Cable, 3m 4 x Stainless steel A4 screws (for Bracket Mount, Control Unit) 2 x Stainless steel A4 screws (for Cradle) 4 x Unit Test Sheets 95-100765 LT-3100 User & Installation Manual NOTE:

Antenna unit mounts (bracket and pole mount) are not included in the LT-3100 Satellite Communications System Basic (P/N: 90-101142) and must be ordered separately. The antenna unit must only be mounted, using the bracket or pole mounted, delivered by Lars Thrane A/S. The antenna unit mounts are listed with part numbers (P/N) in Accessories on page 3. Inspection Inspect the shipping cartons and/or wooden box immediately upon receipt for evidence of damage during transport. If the shipping material is severely damaged or water stained, request that the carrier's agent be present when opening the cartons and/or wooden box. Save all box packing material for future use. After unpacking the system and opening the cartons, inspect it thoroughly for hidden damage and loose components or fittings. If the contents are incomplete, if there is mechanical damage or defect, or if the system does not work properly, notify your dealer. WARNING:

To avoid electric shock, do not apply power to the LT-3100 system components if there is any sign of shipping damage to any part of a unit or the outer cover. Read the Safety Instructions at the front of this manual before installing or operating the unit. Lars Thrane A/S www.thrane.eu Page 2 of 42 LT-3100 User & Installation Manual Rev. 1.04 Accessories Accessories Mounts The following accessory parts are not part of the basic system and must be ordered separately:

91-100772 Flush Mount, Control Unit 91-100773 Bracket Mount (1.5 to 2.5 tube), Antenna Unit 91-100774 Pole Mount (1.5 tube), Antenna Unit Cable and connectors The following cable and connector parts are not part of the basic system and must be ordered separately:

91-100768 Aux Cable, 3m 91-101183 Coaxial cable 4.9mm, 10m 91-101184 Coaxial cable 4.9mm, 25m 91-101137 Coaxial Cable 10.3mm 10m 91-101138 Coaxial Cable 10.3mm 25m 91-101139 Coaxial Cable 10.3mm 50m 91-101140 N Conn. (male) for Coaxial Cable 4.9mm 91-101186 N Conn. (male) for Coaxial Cable 10.3mm 91-101187 Crimping Tool for Coaxial cable 4.9mm 91-101188 Crimping Tool for Coaxial cable 10.3mm Coaxial cables are delivered with one fixed N connector (outdoor mounting), another loose N connector and crimp parts come with the cable. It is required to use an appropriate crimping tool for attaching the loose N connector. NOTE:

For further details on the cable and connectors, please contact Lars Thrane A/S. A coaxial cable up to a length of 500 meters can be used for connecting the LT-3110 Control Unit and the LT-3130 Antenna Unit. Details about the coaxial cable, specification and cable lengths, are described in Antenna on page 20. Lars Thrane A/S www.thrane.eu Page 3 of 42 LT-3100 User & Installation Manual Rev. 1.04 System Overview System Overview The LT-3100 Satellite Communications System is a standalone communication product, which is using the Iridium satellite constellation. The LT-3100 system is working on the Iridium legacy satellites as well as the new Iridium NEXT satellites, which are taking over the Iridium services throughout 2018. An overview of the LT-3100 system is illustrated in Figure 1. Figure 1: LT-3100 system - basic components and interfaces. The LT-3100 system consists of the following units, provided by Lars Thrane A/S:

LT-3110 Control Unit LT-3120 Handset LT-3121 Cradle LT-3130 Antenna Unit NOTE:

The LT-3100 system was released to customers with the initial software version 1.01. Software version 1.01 includes basic voice functionality, together with basic functionality for operating the system. During 2018, software releases will be available, supporting the Iridium legacy services. Please contact Lars Thrane A/S for details about future software releases and features: support@thrane.eu Lars Thrane A/S www.thrane.eu Page 4 of 42 LT-3100 User & Installation Manual Rev. 1.04 Installation and Mounting Installation and Mounting LT-3110 Control Unit The LT-3110 Control Unit is the master unit in the system, supporting all external interfaces and the operational user interface. The LT-3110 Control Unit is designed for indoor mounting. Check the specifications in App. A - Specifications on page 34. Figure 2: LT-3110 Control Unit (front view). The LT-3110 Control Unit has the following interfaces:

2-pin power connector (male), marked PWR Chassis ground connector, marked GNDC N connector (female) for coaxial cable to the LT-3130 Antenna Unit, marked ANT Ethernet (RJ-45) connector, marked LAN 10-pin auxiliary connector (male), marked AUX SIM card, marked SIM 5-pin connector (female) for LT-3120 Handset (front of the control unit) Lars Thrane A/S www.thrane.eu Page 5 of 42 LT-3100 User & Installation Manual Rev. 1.04 Installation and Mounting The LT-3110 Control Unit interfaces are described in Interfaces on page 17. The LT-3110 Control Unit, front and backside view, are illustrated in Figure 2 and Figure 3. Figure 3: LT-3110 Control Unit (backside view). The LT-3110 Control Unit user interface, display and buttons, are described in User Interface (UI) on page 22. NOTE:

The LT-3110 Control Unit must be mounted with either the Bracket Mount, Control Unit

(P/N: 91-100771) or Flush Mount, Control Unit (P/N: 91-100772) - illustrated in Figure 4 and Figure 5. The Flush Mount, Control Unit is not included in the LT-3100 Satellite Communications System Basic (P/N: 90-101142) and must be ordered separately. Mounting and installation considerations:

For optimum system performance, some guidelines on where to install or mount the LT-3110 Control Unit must be followed. It is recommended to mount the unit in a location, which fulfills these requirements:

Mount the unit indoor (not exposed to direct water) Mount the unit using either the bracket mount or flush mount Mount the unit on a rigid structure with a minimum of exposure to vibration and shock Mount the unit in an area with an ambient temperature between -15C to +55C (+5F to +131F) Lars Thrane A/S www.thrane.eu Page 6 of 42 LT-3100 User & Installation Manual Rev. 1.04 Installation and Mounting The Bracket Mount and Flush Mount for the LT-3110 Control Unit are illustrated in Figure 4 and Figure 5. Figure 4: Bracket Mount, Control Unit. Figure 5: Flush Mount, Control Unit. Lars Thrane A/S www.thrane.eu Page 7 of 42 LT-3100 User & Installation Manual Rev. 1.04 Installation and Mounting LT-3120 Handset The LT-3120 Handset is the primary voice interface for the LT-3100 system. The LT-3120 Handset must be connected on the front of the LT-3110 Control Unit. The connector is illustrated in Figure 2 on page 5. Figure 6: LT-3120 Handset (front view). The LT-3120 Handset is connected to the LT-3110 Control Unit via a 5-pin proprietary angle connector. The spiral cord, fixed to the LT-3120 Handset is ~ 0.4 m from handset to connector, when coiled. The spiral cord can be stretched to a maximum of 2 m. The LT-3120 Handset is designed for indoor mounting. Check the Figure 7: LT-3121 Handset (backside view). specifications in App. A - Specifications on page 33. The LT-3120 Handset has the following characteristics:

High-performance audio speaker and microphone Separate ringer (buzzer) Speaker volume control (double-button, marked with + and -, for volume up and down) Built-in off-hook detection circuit NOTE:

NOTE:

The LT-3110 Control Unit will inform the user if the LT-3120 handset is not properly connected to the LT-3110 Control Unit. The following user information will be showed in the display Handset not connected. The LT-3120 Handset must be operated together with the LT-3121 Cradle, for the off-hook detection circuit to work. The LT-3121 Cradle is described in LT-3121 Cradle on page 9. Lars Thrane A/S www.thrane.eu Page 8 of 42 LT-3100 User & Installation Manual Rev. 1.04 Installation and Mounting LT-3121 Cradle The LT-3121 Cradle is used together with the LT-3120 Handset. The LT-3121 Cradle should be mounted next to the LT-3110 Control Unit, supporting the LT-3120 Handset. The LT-3121 Cradle specifications are available in App. A - Specifications on page 33. Figure 9: LT-3121 Cradle (front view). Figure 8: LT-3121 Cradle (backside view) IMPORTANT: The LT-3121 Cradle contains a magnet, to hold on to the LT-3120 Handset. Make sure that other electronic equipment is installed in a distance respecting the compass safe distance of 0.4 m (1.3 ft). An outline drawing for the LT-3121 Cradle is available in App. I - Outline Drawing: LT-3121 Cradle on page 42. Lars Thrane A/S www.thrane.eu Page 9 of 42 LT-3100 User & Installation Manual Rev. 1.04 Installation and Mounting LT-3130 Antenna Unit The LT-3130 Antenna Unit is designed for outdoor mounting and connected to the LT-3110 Control Unit via a coaxial cable. The LT-3130 Antenna Unit specifications are available in App. A - Specifications on page 34. The LT-3130 Antenna Unit has an N connector (female) mounted, centered at the bottom of the antenna. Figure 10: LT-3130 Antenna Unit. Mounting and installation considerations:

The LT-3130 Antenna Unit has an N connector (female) at the bottom side of the unit. Mount the unit vertically (with the N connector pointing down) Mount the unit with free line of sight to the Iridium and GNSS satellites. Make sure that the unit can receive signals from the Iridium and GNSS satellites (satellite reception information is available in the LT-3110 Control Unit user interface display, see Figure 25 on page 24) Mount the unit on a rigid structure with a minimum of exposure to vibration and shock Mount the unit using either the Bracket Mount or Pole Mount provided by Lars Thrane A/S Mount the unit outdoor with an ambient temperature between -25C to +55C (-13F to +131F) Mount the unit with a minimum angle of 20 degrees towards a radar antenna (above or below) and keep a minimum distance of 2.5 m (8 ft) Mount the unit at least 1 m. (3 ft.) away from radio transmitting antennas (VHF, UHF, MF-HF) Mount the unit away from Inmarsat and transmitting VSAT antennas Lars Thrane A/S www.thrane.eu Page 10 of 42 LT-3100 User & Installation Manual Rev. 1.04 Installation and Mounting WARNING:

The safety distance from the LT-3130 Antenna Unit, is 0.1 m (0.3 ft), in order to comply with the regional regulations. IMPORTANT: Due to the adjacency of the Iridium and Inmarsat frequency bands, the LT-3100 Satellite Communications System may not co-operate in the proximity of active Inmarsat equipment. The LT-3130 Antenna Unit must be installed outside the radar main beam. Typically, this is in the order of 20 degrees. To avoid near field antenna coupling, a minimum distance of 2.5 m (6 ft) between the radar antenna and the LT-3130 Antenna Unit must be obeyed. Figure 11 is illustrating how the LT-3130 Antenna Unit should be mounted to avoid interference from radars. Figure 11: LT-3130 Antenna Unit Avoid Radar Beam. IMPORTANT: Failing to obey the specified installation conditions will void the warranty. However, depending on the specific radar frequency and power level, the separation distance between the radar and the LT-3130 Antenna Unit may be reduced, with no impact on the antenna performance. The performance of the LT-3130 Antenna Unit should be validated when the LT-3100 system is installed. Lars Thrane A/S www.thrane.eu Page 11 of 42 LT-3100 User & Installation Manual Rev. 1.04 Installation and Mounting The LT-3130 Antenna Unit shall me mounted minimum 1 m from MF-HF, VHF, and UHF antennas. Figure 12: LT-3130 Antenna Unit Separation to MF-HF, VHF, and UHF antennas. The LT-3130 Antenna Unit must be installed with a 360 clear view of the sky. However, minor obstructions such as a mast will not degrade the antenna performance severely, if a separation distance larger than 15 times the diameter of the obstruction is kept. Figure 13: LT-3130 Antenna Unit Separation distance to minor obstructions. NOTE:

The LT-3130 Antenna Unit must be mounted using one of the following antenna mounts:

91-100773 Bracket Mount (1.5 to 2.5 tube), Antenna Unit 91-100774 Pole Mount (1.5 tube), Antenna Unit Lars Thrane A/S www.thrane.eu Page 12 of 42 LT-3100 User & Installation Manual Rev. 1.04 Installation and Mounting Bracket Mount, Antenna Unit The Bracket Mount (1.5 to 2.5 tube), Antenna Unit installation options are illustrated in Figure 14 to Figure 17. Figure 15: Bracket Mount (1.5 to 2.5 tube), Antenna Unit vertical tube mount. Figure 14: Bracket Mount (1.5 to 2.5 tube), Antenna Unit vertical tube mount. Bracket mount installation procedure:

1. Fasten the bracket mount to a tube (max. 2.5 tube) by using the two V-bolts and the M8 prevailing nuts, as illustrated in Figure 17 on page 14 (max torque = 5.5 Nm) 2. Screw on the LT-3130 Antenna Unit and secure the antenna lock pinot (max torque = 1.2 Nm) 3. Fasten the coaxial cable to the LT-3130 Antenna Unit (N connector) 4. Apply self-volcanic tape on the N connector and cable to protect against saltwater and corrosion NOTE:

NOTE:

Always fasten the Bracket Mount, Antenna Unit (1.5 to 2.5 tube) to the tube, before installing the LT-3130 Antenna Unit (the antenna unit and bracket mount are fastened together by the thread lock). Remember to secure the pinot screw after the antenna unit has been fastened. The torques are specified in Figure 17 on page 14. The Bracket Mount (1.5 to 2.5 tube), Antenna Unit interfaces to a tube of maximum 2.5

(63.5 mm), measured outer diameter. Lars Thrane A/S www.thrane.eu Page 13 of 42 LT-3100 User & Installation Manual Rev. 1.04 Installation and Mounting Figure 16: Bracket Mount (1.5 to 2.5 tube), Antenna Unit horizontal tube mount. The Bracket Mount (1.5 to 2.5 tube), Antenna Unit can support tubes in the interval 1.5 to 2.5. The torques are specified in Figure 17. The bracket mount, V-bolts, and nuts are all made of A4 stainless steel Figure 17: Bracket Mount (1.5 to 2.5 tube), Antenna Unit horizontal tube mount. Lars Thrane A/S www.thrane.eu Page 14 of 42 LT-3100 User & Installation Manual Rev. 1.04 Installation and Mounting Pole Mount, Antenna Unit The Pole Mount (1.5 tube), Antenna Unit is illustrated in Figure 18 to Figure 20. Figure 18: Pole Mount (1.5 tube), Antenna Unit. Pole mount installation procedure:

1. Feed the coaxial cable through the pole mount 2. Fasten the coaxial cable to the LT-3130 Antenna Unit (N connector) 3. Apply self-volcanic tape on the N connector and cable to protect against saltwater and corrosion 4. Screw the pole mount (clockwise) on the LT-3130 Antenna Unit, and fasten the antenna lock pinot screw, as illustrated in Figure 20 (max torque = 1.2 Nm) 5. The LT-3130 Antenna Unit and pole mount can now be mounted on the 1.5 tube. Fasten the three pole lock pinot screws, as illustrated in Figure 19 (max torque = 4.5 Nm) NOTE:

NOTE:

Remember to fasten the antenna lock pinot screw (1.2 Nm) after the pole mount and antenna unit have been screwed together. The Pole Mount (1.5 tube), Antenna Unit interfaces to a tube of maximum 1.5 (38.1 mm), measured outer diameter. Lars Thrane A/S www.thrane.eu Page 15 of 42 LT-3100 User & Installation Manual Rev. 1.04 Installation and Mounting Figure 19: Pole Mount (1.5 tube), Antenna Unit. Figure 20: Pole Mount (1.5 tube), Antenna Unit. NOTE:

The Pole Mount (1.5 tube), Antenna Unit only support a 1.5 tube. The pinot screws

(antenna and pole lock) torques are specified in Figure 19 and Figure 20. The pole mount is made of milled aluminum (anodized). The pinot screws are made of A4 stainless steel. Lars Thrane A/S www.thrane.eu Page 16 of 42 LT-3100 User & Installation Manual Rev. 1.04 Interfaces Interfaces This section will describe all the external interfaces to the LT-3110 Control Unit, including the coaxial cable interface to the LT-3130 Antenna Unit. DC input The LT-3100 system is designed to be used on 12 VDC and 24 VDC power buses (nominal). External DC power to the LT-3100 system is provided by connecting the proprietary 91-100767 power cable, 3m -

delivered by Lars Thrane A/S. The power connector is mounted on the back side of the LT-3110 Control Unit and marked PWR, see Figure 3 on page 6. NOTE:

The input voltage range is: 10 - 32 VDC. The LT-3110 Control Unit DC input connector and circuit is protected and certified for Reverse Polarity Protection. Use only the 91-100767 power cable, 3m delivered by Lars Thrane A/S. Chassis ground The chassis ground connector is placed on the back side of the LT-3110 Control Unit and marked with GNDC, see Figure 3 on page 6. SIM card The LT-3100 system requires a SIM card to be operated with the Iridium satellite services. The Iridium SIM card must be bought from one of the official Iridium Service Providers. A list of Iridium Service Providers can be found at the Iridium website: https://www.iridium.com (select Services, and hereafter Voice). The LT-3100 system is supporting pre- and postpaid SIM card subscriptions. The SIM card must be inserted in the LT-3110 Control Unit behind the rubber dust cover. Make sure that the LT-3110 Control Unit is powered off before opening the rubber dust cover. When the SIM card is properly inserted in the slot, and the rubber dust cover is secured, the LT-3110 Control Unit can be powered up. The rubber dust cover is illustrated in Figure 3 on page 6 and marked with SIM. The following procedure must be followed when inserting, replacing, or removing the SIM card:

1. Turn off the power to the LT-3110 Control Unit 2. Remove the rubber dust cover on the back side of the LT-3110 Control Unit 3. Slide the SIM card holder as illustrated with the arrows on the PCB print, to unlock 4. Open the SIM card holder and insert or remove the SIM card 5. Close the SIM card holder 6. Slide the SIM card holder as illustrated with the arrows on the PCB (opposite direction), to lock 7. Re-insert the rubber dust cover 8. Turn on power to the LT-3110 Control Unit Lars Thrane A/S www.thrane.eu Page 17 of 42 LT-3100 User & Installation Manual Rev. 1.04 Interfaces NOTE:

The LT-3110 Control Unit must be powered off when inserting, changing, or removing the SIM card. The SIM card is hidden behind the rubber dust cover on the back side of the LT-

3110 Control Unit. Figure 21 is showing an Iridium SIM card. The format is Mini-SIM (2FF) 25 x 15 mm. The SIM card must be removed from the full-sized card carrier by breaking the Mini-SIM out. The full-sized card carrier contains the MSISDN number, while the SIM card itself contains the ICC-ID. Figure 21: Iridium SIM card The SIM card will be delivered from the Iridium Service Provider (ISP) together with the essential information:

ICC-ID MSISDN number (the Iridium voice number) PIN codes PUK codes The SIM card will be delivered with the SIM lock feature disabled. Thus, the LT-3100 system will be operational as soon as the SIM card is inserted. If the user decides to activate the SIM lock function from the UI display, then the PIN code is required next time the LT-3100 system is powered up. NOTE:

Change of the SIM card PIN code can only be performed, if the PIN lock is enabled. If changing the SIM card PIN code, then the SIM card default PIN code cannot be restored, and the new PIN code must be used to unlock the SIM card and the Iridium services. Lars Thrane A/S www.thrane.eu Page 18 of 42 LT-3100 User & Installation Manual Rev. 1.04 Interfaces Ethernet (RJ45) The LT-3110 Control Unit has an Ethernet LAN (RJ-45) interface, currently supporting service &

maintenance. The Ethernet interface must be used to access the built-in web server, which is further described in Web server on page 30. The LT-3110 Control Unit will automatically request and obtain an IP address when connected to a Local Area Network (LAN) with a DHCP server (e.g. a router). If connecting the LT-3110 Control Unit directly to a PC, the two will automatically negotiate an IPv4 Link-Local address. The current IP address can be found in the user interface display (Menu -> System -> Network: IP Address). Auxiliary The auxiliary connector is a 10-pin connector (male) mounted on the backside of the LT-3110 Control Unit as illustrated in Figure 3 on page 6 and marked with AUX. The auxiliary connector supports the following interfaces:

RS-422 serial interface 2 x Input/output (I/O) The auxiliary interface is not supported in software version 1.01. NOTE:

Use only the 91-100768 Auxiliary Cable, 3m delivered by Lars Thrane A/S for connecting to the auxiliary connector on the backside of the LT-3110 Control Unit. The Auxiliary Cable, 3m is an accessory part and must be acquired separately. Lars Thrane A/S www.thrane.eu Page 19 of 42 LT-3100 User & Installation Manual Rev. 1.04 Interfaces Antenna The LT-3110 Control Unit and the LT-3130 Antenna Unit must be connected using a coaxial cable. Both the control unit and the antenna unit has a N connector (female) mounted. This section will specify the requirements to the coaxial cable. The minimum set of requirements are specified in Table 2 and Figure 22. Cable impedance Maximum signal loss Maximum DC resistance Table 2: Minimum requirements for the coaxial cable connecting the LT-3110 Control Unit and LT-3130 Antenna Unit. 50 47.7 dB/100 m @ 1.5 GHz See Figure 22. In most cases it will be the DC resistance that will determine the maximum length of the coaxial cable. It is important to note that the input voltage of the control unit is important for the length of the coaxial cable that can be used. The following formula can be used to calculate the length of the coaxial cable:

() =

2 1000 4 where U is the control unit input voltage [V], PD is the antenna unit power (10 W), and RCable is the total DC resistance [/km] (sum of inner and outer conductor resistance). Figure 22: Coaxial Cable Total DC Resistance vs. Cable Length (12 VDC and 24 VDC). Lars Thrane A/S www.thrane.eu Page 20 of 42 LT-3100 User & Installation Manual Rev. 1.04 Interfaces In Figure 22 two different input voltages (12 VDC and 24 VDC) illustrate the maximum length of the coaxial cable as a function of the DC cable resistance. NOTE:

The DC cable resistance that is illustrated in Figure 22 and used to calculate the maximum cable length is the sum of the DC inner conductor resistance and the DC outer conductor resistance. Some data sheets are not providing sufficient information about the DC resistance, in which cases, the cable manufacture must be approached to obtain this information. Lars Thrane A/S has calculated the maximum allowed cable lengths with two coaxial cables as illustrated in Table 3. The two cables are FF195LSFROH (~RG-58) and FF400LSFROH (~RG-214). Cable Type 12 VDC Supply Max Cable Length 24 VDC Supply Max Cable Length FF195LSFROH (4.9mm) FF400LSFROH (10.3mm) 70 m 265 m 285 m 500 m Table 3: Maximum coaxial cable length to be used on 12 VDC and 24 VDC (cable examples). The cable lengths calculated in Table 3 are obtained by reducing the input voltage by 10% (10.8 VDC and 21.6 VDC) to compensate for variation in the power source. The total DC resistance for the two cables are:

Cable Type Inner Conductor DC Resistance [/km]

Outer Conductor DC Resistance [/km]

FF195LSFROH (4.9mm) FF400LSFROH (10.3mm) Table 4: Total DC resistance (cable examples). 24.9 4.5 15.8 6.5 Total DC Resistance

[ /km]

40.7 11 IMPORTANT:

NOTE:

If using a coaxial cable that is different to what is specified in this section (FF195LSFROH and FF400LSFROH), then verify that the coaxial cable maximum signal loss (listed in Table 2) is respected and calculate the maximum cable length as a function of the input voltage and the total DC resistance. Contact Lars Thrane A/S to get assistance on selection and acceptance of a specific coaxial cable. The LT-3110 Control Unit must be powered off when connecting or disconnecting the LT-

3130 Antenna Unit. Lars Thrane A/S www.thrane.eu Page 21 of 42 LT-3100 User & Installation Manual Rev. 1.04 User Interface (UI) User Interface (UI) The LT-3100 system is controlled from the LT-3110 Control Unit, which is the interface for operating and configuring the system. The control unit has a 4.3 TFT-LCD display, supporting day and night modes. The layout of the display and buttons is illustrated in Figure 23. Figure 23: Control Unit (front view) user interface display and buttons. The control unit buttons, function and features, are described in the following groups:

Power button: The power button can power off the system by pressing the button for 5 seconds. A pop-up box will show the action, and a counting is showing the count down until the system is powered off. If the external power source to the system is re-powered, then the system will power on. Brightness button: The brightness button has two functions change of brightness level and change of display mode (day and night). When changing the brightness level, the keypad backlight will be changed as well. Short press (< 1 s); brightness level will change between 7 levels. Long press ( 1 s); will change display mode. The display brightness level and display mode can be changed from the UI menu as well (Menu -> Settings -> Display). Off-hook button: The button is illustrated with a green colored handset. The off-hook buttons function is to activate a call, if the dialed number is available in the display or a contact is selected in the Call History. The off-hook button can also be used to accept an incoming call. The alternative to use the off-hook button is to lift the handset out of the cradle. If the off-hook button is used and the handset remain in the cradle, the phone audio will be available in the control unit speaker. On-hook button: The button is illustrated with a red colored handset. Pressing the on-hook button will terminate an active call. MENU button: The MENU button is used to open the main menu, as illustrated in Figure 24. The BACK, arrows, and ENTER buttons are used to navigate in the menu layout. Press the MENU button to exit the menu from anywhere in the menu tree (instead of multiple BACK button presses). Soft keys buttons: Three soft keys are available below the display. The soft keys are used for different purposes and their functions will change in the operation modes of the system. Navigation buttons: The navigation buttons (BACK, arrows, and ENTER) are used for navigation purposes in the menu layout. In context of user input or when making selections, the BACK button will erase input or cancel editing respectfully, the ENTER button will end input or apply selection respectfully. Lars Thrane A/S www.thrane.eu Page 22 of 42 LT-3100 User & Installation Manual Rev. 1.04 User Interface (UI) Numeric Keypad buttons: The numeric keypad buttons, the '*' button, and the '+' button can be used for entering digits, letters and special characters. Depending on context, pressing one button in rapid succession (< 1s) will cycle through a selection of letters, digits and/or special characters

(e.g. when entering a phone number, pressing the '*' character twice in succession will result in one

'+' character and not two '*' characters). An icon in the status bar will show the current input mode, which determines which characters can be cycled - if any. In text mode, the '#' key is used to change between capital and lowercase letters. Menu The LT-3100 systems main menu is accessed by pressing the MENU button on the keypad. The user will be presented with a layout as illustrated in Figure 24. Figure 24: LT-3110 Control Unit - UI display (main menu). The main menu is represented by three sub-menus: Phone, Settings, and System. The three sub-menus are listed in Table 5. Sub-menus Entries Phone Settings System Contacts Audio Display Information Network Security Table 5: LT-3110 Control Unit, sub-menu layout. Lars Thrane A/S www.thrane.eu Page 23 of 42 LT-3100 User & Installation Manual Rev. 1.04 User Interface (UI) System information The LT-3100 system installation and mounting is described in the previous sections. After the LT-3100 system has been installed and properly connected, the system will automatically start-up and register on the Iridium Network and be ready for use. The LT-3100 system will inform the user, if the system is not properly installed, or the system cannot register onto the Iridium Network. Figure 25 is illustrating a LT-

3100 system, which is registered on the Iridium Network and ready to use. The LT-3100 system will provide user information in the status bar and status text (e.g. Registered showed below the Iridium connected logo). Status bar System text Figure 25: LT-3110 Control Unit - UI display (status view). The signal strength icon will be showed with a signal strength between 0 and 5 (where 5 is the maximum signal strength), when the LT-3100 system is registered on the network and ready to use. If no signal is available, the signal bar symbol will be showed with no highlighted bars and a small cross. The status text will show Registered, if the system is ready to use. Table 6 gives an overview of the possible combinations, of the signal strength icon, and the status text that the LT-3100 system can represent. Signal Bar 0 to 5 0 to 5 No bars (with cross) System Text Registered Registering Searching for Iridium System Status Ready to use Not ready Not ready Table 6: LT-3110 Control Unit Registration status. Lars Thrane A/S www.thrane.eu Page 24 of 42 LT-3100 User & Installation Manual Rev. 1.04 User Interface (UI) Additional user information is available in the system and represented as a system text or as an icon in the status bar. Table 7 is listing the system text and describing the status of the LT-3100 system. System Text Initializing, please wait Searching for Iridium Registering Registered Antenna not connected Handset not connected SIM card missing SIM card locked SIM card blocked SIM card error Description The LT-3100 system is starting up. Please wait until the system text is updated. The LT-3100 system is searching for the Iridium satellites signal. Make sure that the LT-3130 Antenna Unit has free line of sight to the Iridium satellites. The LT-3100 system is registering onto the Iridium Network. The LT-3100 system is registered on the Iridium Network. The LT-3110 Control Unit and LT-3130 Antenna Unit is not connected via the coaxial cable. Verify coaxial cable connections, specifications, and details in Antenna on page 20. The LT-3120 Handset is not connected to the LT-

3110 Control Unit. Phone calls cannot be performed from the LT-3120 Handset. The LT-3110 Control Unit cannot identify a SIM card in the SIM slot. Check that a SIM card has been inserted behind the rubber dust cover on the back side of the control unit. For further details, see SIM card on page 17. The SIM lock has been enabled by the user (or SIM lock is default enabled in the SIM card). Type in the SIM card PIN code. The SIM lock can be disabled by the user from the UI display (Menu -> System ->

Security). The SIM card PIN code has been typed in incorrect three consecutive times. Type in the SIM card PUK code to deactivate the SIM card blocked mode. The SIM card error might appear, if the SIM card is detected, but the SIM card format or data is wrong. Please power down the LT-3110 Control Unit, verify correct SIM card re-insert, and re-

power the system again. System Status Not ready Not ready Not ready Ready to use Not ready

(Not ready) Not ready Not ready Not ready Not ready Table 7: LT-3110 Control Unit System Text Lars Thrane A/S www.thrane.eu Page 25 of 42 LT-3100 User & Installation Manual Rev. 1.04 User Interface (UI) The LT-3100 system can in addition to the system text also show an icon, which might be related to the status text, but not necessarily. The icon will be available in the icon line and might indicate a problem, but can also indicate a status of the system, or a service information to the user. Table 8 is providing an overview of the available icons. Status Icon Description The LT-3100 system has no satellite signal and cannot register on the Iridium Network. No satellite services available. The LT-3100 system has satellite signal = 0 and is registered on the Iridium Network. Check system text for registration status. The LT-3100 system has satellite signal = 1 and registered on the Iridium Network. Check system text for registration status. The LT-3100 system has satellite signal = 5 and registered on the Iridium Network. Check system text for registration status. The handset icon indicates that the LT-3100 system is in off-hook mode and that a potential call is active. The mute icon indicates, that the microphone on the handset is muted. Mute and unmute is activated from a soft key (below the display) during a call. The ringer mute icon is showed when the ringer volume is configured to off. The numeric icon is showed when the user is writing a numeric number in the display. The alphanumeric icon (capital letter) is showed when the user is writing a capital alphabetic letter in the display. Change between normal and capital letter by using the # key. The alphanumeric icon is showed when the user is writing a normal alphabetic letter in the display. Change between normal and capital letter by using the # key. The no SIM card icon is showed if the LT-3110 Control Unit is powered up without having a SIM card inserted, or the SIM card has not been detected. The warning symbol is showed if something is wrong with the system. Check system text for further information or action. Table 8: LT-3110 Control Unit Status Icons. Lars Thrane A/S www.thrane.eu Page 26 of 42 LT-3100 User & Installation Manual Rev. 1.04 User Interface (UI) Make a voice call The LT-3100 system must be properly installed, connected, and configured before trying to establish a phone call. The LT-3100 system will inform the user about the status of the system, and whether the system is ready to initiate a call. NOTE:

Verify that the LT-3100 system is ready for making a voice call. Check that the system status

(system text and icons), as described in System information on page 24, shows the correct system information. Dialing a mobile originating (MO) voice call can be established in the two following modes:

On-hook mode (dial the number, and then off-hook) Off-hook mode (lift the handset, get ready tone, and dial the number) On-hook mode:

In on-hook mode the user types in the called number, using the numeric keypad, without lifting the handset out of the cradle or initially pressing the off-hook button. The typed in called number can be edited until the user decides to press the off-hook button or lifting the handset out of the cradle. Figure 26: LT-3110 Control Unit voice call (on-hook mode). On-hook mode (step-by-step):

1. Type in the called number (e.g. 004588301089) using the numeric keypad 2. When the called number is complete:

a. Lift the handset out of the cradle or b. Press the off-hook button (green handset button) 3. The LT-3100 system will now establish a connection to the dialed number Lars Thrane A/S www.thrane.eu Page 27 of 42 LT-3100 User & Installation Manual Rev. 1.04 User Interface (UI) Off-hook mode:

In off-hook mode, the user starts to place the LT-3100 system into off-hook mode (ready tone available). The off-hook mode can be obtained in two ways: lifting the handset out of the cradle or pressing the green off-hook button, prior to typing any digits of the called number. In off-hook mode, the user will be met by a ready tone and the help text Please enter number hereafter, the called number can be dialed, using the numeric keypad. It is not possible to regret, if one or more wrong digits are typed in, for the dialed number. In this case, the user must on-hook the phone, and dial the correct number again. Figure 27: LT-3110 Control Unit voice call (off-hook mode). Off-hook mode (step-by-step):

1. Lift the handset out of the cradle or press the off-hook button (green handset button) 2. Confirm that a ready tone is available in the handset, or in the control unit speaker 3. Please enter number: user can now enter the called number 4. When the called number is complete, the user has three options:

a. Wait 12 seconds, hereafter the system will try to call the number b. Press #, hereafter the call will be established immediately c. Press the off-hook button 5. The LT-3100 system will now establish a connection to the called number NOTE:

The LT-3100 system will provide the user with information, while connecting and throughout the voice call. In case of problems with the satellite network or connection to the called party (far-end), the user will be informed through a voice prompt, and by status cause codes, that will be presented on the display (e.g. Temporary link failure). Lars Thrane A/S www.thrane.eu Page 28 of 42 LT-3100 User & Installation Manual Rev. 1.04 User Interface (UI) The voice call connection can be described with the following states:

State 1: Type in number State 2: Connecting State 3: Duration: MM:SS (if call is successfully connected) where MM are minutes and SS are seconds. The Connecting and Duration: MM:SS states are illustrated in Figure 28 and Figure 29. Figure 28: LT-3110 Control Unit voice call connecting Figure 29: LT-3110 Control Unit voice call successfully connected. Lars Thrane A/S www.thrane.eu Page 29 of 42 LT-3100 User & Installation Manual Rev. 1.04 Web server Web server The LT-3110 Control Unit has a built-in webserver, which can be accessed from the Ethernet (RJ45) interface from the back side of the control unit. A PC must be connected to the control unit, either directly by connecting an Ethernet cable between a PC and the LT-3110 Control Unit, or by connecting the LT-3110 Control Unit to a Local Area Network (LAN), to where the PC is connected. NOTE:

The IP address allocated to the LT-3110 Control Unit, is shown in the UI (Menu -> System ->

Network: IP Address). The web server has three web pages:

Dashboard Software update Diagnostic report Figure 30: LT-3110 Control Unit - built-in web server (dashboard). Lars Thrane A/S www.thrane.eu Page 30 of 42 LT-3100 User & Installation Manual Rev. 1.04 Web server Dashboard The dashboard is showing details about the two main units, which forms the Satcom system: the LT-3110 Control Unit and the LT-3130 Antenna Unit. If the antenna unit is connected properly to the control unit, then the antenna unit will be visible on the web server dashboard, as illustrated in Figure 30. Otherwise only the control unit will be visible. For each unit, the following information will be available: unit number, unit name, unit part number, unit serial number, and software version. The antenna unit will automatically be updated with the software version, which is available in the control unit. Software update Carefully read the software release note, provided by Lars Thrane A/S, before software updating the LT-

3100 system. Navigate to the web server of the LT-3100 system, by following the instructions in Accessing the built-in web server on page 32. Select the Software update webpage and click the Browse button to select the LT-3100 system file, which must be uploaded to the system. The LT-3100 software image has the following filename (example): LT-3100-v1.01R-005.lti the software image and release documentation will be available on the official company website: www.thrane.eu, under the specific product. Finally click the Upload button to start the upload of the new software image. The upload and installation of the software image will take a few minutes. Progress indication bars can be monitored on the software update webpage, while the software update is on-going. The LT-3100 system will reboot, once the software image is installed in both the control unit and antenna unit. NOTE:

The LT-3110 Control Unit and the LT-3130 Antenna Unit must be operated with the same software version. Automatically, software update will happen if the control unit identifies that the software version in the two units are different. IMPORTANT: Do not remove power from the control unit while the software update is on-going. Also, do not disconnect the antenna cable between the control unit and the antenna unit, while the software update is on-going. Diagnostic report A diagnostic report can be downloaded from the webpage Diagnostics. Navigate to the webpage and press the download button. A file with the following filename (example): LT-3100_00000061_180104-

152149.tar.gz will be downloaded to a location selected by the user. The diagnostic report can be sent back to Lars Thrane A/S in case of required support and assistance. The diagnostic report contains technical data, from the LT-3100 system, and will help identify and resolve problems at the installation site. This is to avoid sending back the LT-3100 system for unnecessary debug and repair, at the Lars Thrane A/S facility. Lars Thrane A/S www.thrane.eu Page 31 of 42 LT-3100 User & Installation Manual Rev. 1.04 Web server Accessing the built-in web server To access the built-in web server of the LT-3110 Control Unit, please complete the following steps:

1. Connect the LT-3110 Control Unit directly to a PC using an Ethernet cable, or connect the LT-3110 2. Control Unit to a Local Area Network (LAN), where a PC is connected. Identify the IP address that is assigned to the LT-3110 Control Unit. The IP address can be read out from the UI Display interface (Menu -> System -> Network: IP Address). The IP address is valid if the Link Status is showing Up. The IP address is assigned dynamically by a DHCP server. 3. From the PC, start a browser (e.g. Microsoft Edge, Explorer, or Chrome) and type in the IP address, which was identified in the LT-3110 Control Unit (e.g. 169.254.1.1). 4. The browser might show you a warning about an invalid web server certificate, as illustrated in Figure 31. Make sure, that you have typed in the correct IP address. 5. Press Details and you will be presented for an extended page view (including a link), which will direct you to the LT-3100 System dashboard Go on to the webpage (Not recommended). 6. You will now see the LT-3100 system dashboard. Figure 31: Accessing built-in web server (This site is not secure). Lars Thrane A/S www.thrane.eu Page 32 of 42 LT-3100 User & Installation Manual Rev. 1.04 Service & Repair Service & Repair This section describes what the end-user must do in case of required service or repair. NOTE:

The LT-3100 system does not require any scheduled maintenance or service. Make sure that the product is installed, as described in this manual, before making contact to the distributor or dealer for further assistance. If the LT-3100 system for some reason does not work as described in this manual, make contact with the distributor or dealer, from where the product was originally bought. The distributor or dealer will have experience and know-how to assist with further technical support and troubleshooting. Contacting the distributor/dealer:

1) Make sure to have the product name, unit part numbers, and unit serial numbers identified. The unit part numbers and the unit serial numbers are identified on the unit label, which is found on the backside, or at the bottom side of the units. Alternatively, use the built-in web server to read-

out the unit part numbers and the unit serial numbers. 2) Write a technical report about the observation or error. If possible, attach a picture of the installed product and include a wiring diagram. If possible, download a diagnostic report as described in Diagnostic report on page 31. 3) Send all information to the local distributor or dealer. IMPORTANT: Unless otherwise agreed, the end-user shall always coordinate service and repair issues directly with the distributor or dealer. This practice also applies for returning of products for service and repair. All information that will get back to Lars Thrane A/S, either directly or indirectly, will be handled with confidentiality. End-user sensitive data will not be shared with any third party without prior written acceptance from the involved parties. Lars Thrane A/S www.thrane.eu Page 33 of 42 LT-3100 User & Installation Manual Rev. 1.04 Appendixes Appendixes App. A - Specifications LT-3100 Satellite Communications System Certification & standards Vibration, operational Vibration, survival Vibration, shock Power consumption: operating mode, max Power consumption: standby mode, max Power consumption: sleep mode, max Compass Safe Distance, std. Compass Safe Distance, steer. LT-3110 Control Unit Weight Dimensions Temperature, operational IP rating, dust and water Interfaces Input voltage LT-3120 Handset Weight Dimensions Temperature, operational IP rating, dust and water LT-3121 Cradle Weight Dimensions LT-3130 Antenna Unit Weight Dimensions Temperature, operational IP rating, dust and water Interfaces Antenna communication cable Warranty Maintenance Maritime CE, IC, FCC, RCM, RoHS, Iridium IEC 60945 (sine) & proprietary Maritime Random profile Proprietary Maritime Random profile Proprietary Maritime profile (20 g, 11 ms) 37 W 21 W 0.08 W 0.85 m (2.8 ft) 0.65 m (2.1 ft) 658 g (1.45 lbs) 224.0 x 120.0 x 70.0 mm (8.82 x 4.72 x 2.76 in)

-15C to +55C (+5F to +131F) IP 32 Ethernet, auxiliary, DC input, chassis ground Antenna Unit (N conn.), handset, Bluetooth, SIM card 10 - 32 VDC 290 g (0.64 lbs) 208.8 x 52.8 x 38.2 mm (8.22 x 2.08 x 1.50 in)

-15C to +55C (+5F to +131F) IP32 66 g (0.15 lbs) 106.9 x 57.4 x 29.3 mm (4.21 x 2.26 x 1.15 in) 687 g (1.51 lbs) 151.1 x 149.5 mm (5.95 x 5.89 in)

-25C to +55C (-13F to +131F) IP67 Control Unit (N conn.) Coaxial cable, up to 500 m (1500 ft) 2 years None Lars Thrane A/S www.thrane.eu Page 34 of 42 LT-3100 User & Installation Manual Rev. 1.04 Appendixes App. B - Outline Drawing: LT-3110 Control Unit Figure 32: Outline Drawing: LT-3110 Control Unit Lars Thrane A/S www.thrane.eu Page 35 of 42 LT-3100 User & Installation Manual Rev. 1.04 Appendixes App. C - Outline Drawing: Bracket Mount, Control Unit Figure 33: Outline Drawing: Bracket Mount, Control Unit Lars Thrane A/S www.thrane.eu Page 36 of 42 LT-3100 User & Installation Manual Rev. 1.04 Appendixes App. D - Outline Drawing: Flush Mount, Control Unit Figure 34: Outline Drawing: Flush Mount, Control Unit Lars Thrane A/S www.thrane.eu Page 37 of 42 LT-3100 User & Installation Manual Rev. 1.04 Appendixes App. E - Outline Drawing: LT-3130 Antenna Unit Figure 35: Outline Drawing: LT-3130 Antenna Unit Lars Thrane A/S www.thrane.eu Page 38 of 42 LT-3100 User & Installation Manual Rev. 1.04 Appendixes App. F - Outline Drawing: Pole Mount, Antenna Unit NOTE:

The Pole Mount (1.5 tube), Antenna Unit interfaces to a tube of maximum 1.5 (38.1 mm), measured outer diameter. The total weight of the Pole Mount is 190 g (0.42 lbs). Figure 36: Outline Drawing: Pole Mount (1.5 tube), Antenna Unit Lars Thrane A/S www.thrane.eu Page 39 of 42 LT-3100 User & Installation Manual Rev. 1.04 Appendixes App. G - Outline Drawing: Bracket Mount, Antenna Unit NOTE:

The Bracket Mount (1.5 to 2.5 tube), Antenna Unit interfaces to a tube of maximum 2.5

(63.5 mm), measured outer diameter. The total weight of the Bracket Mount is 714 g (1.57 lbs). Figure 37: Outline Drawing: Bracket Mount (1.5 to 2.5 tube), Antenna Unit Lars Thrane A/S www.thrane.eu Page 40 of 42 LT-3100 User & Installation Manual Rev. 1.04 Appendixes App. H - Outline Drawing: LT-3120 Handset Figure 38: Outline Drawing: LT-3120 Handset Lars Thrane A/S www.thrane.eu Page 41 of 42 LT-3100 User & Installation Manual Rev. 1.04 Appendixes App. I - Outline Drawing: LT-3121 Cradle Figure 39: Outline Drawing: LT-3121 Cradle Lars Thrane A/S www.thrane.eu Page 42 of 42 Lars Thrane A/S Skovlytoften 33 2840 Holte Denmark www.thrane.eu