FCC ID: 2APTR-GEARSCAN Professional Diagnostic Tool

V1.00.000 21-03-2018 Statement: LAUNCH owns the complete intellectual property rights for the software used by this product. For any reverse engineering or cracking actions against the software, LAUNCH will block the use of this product and reserve the right to pursue their legal liabilities. Trademark Information LAUNCH is a registered trademark of LAUNCH TECH CO., LTD. (LAUNCH) in China and other countries. All other LAUNCH trademarks, service marks, domain names, logos and company names referred to in this manual are either trademarks, registered trademarks, service marks, domain names, logos and company names of or are otherwise the property of LAUNCH or its affiliates. In countries where any of the LAUNCH trademarks, service marks, domain names, logos and company names are not registered, LAUNCH claims other rights associated with unregistered trademarks, service marks, domain names, logos and company names. Other products or company names referred to in this manual may be trademarks of their respective owners. You may not use any trademark, service mark, domain name, logo, or company name of LAUNCH or any third party without permission from the owner of the applicable trademark, service mark, domain name, logo, or company name. You may contact LAUNCH at www.launchusa. com, or write to LAUNCH Tech(USA), Inc., 1820 S. Milliken Ave. Ontario, CA 91761, to request written permission to use Materials on this manual for purposes or for all other questions relating to this manual. Copyright Information Copyright 2018 by LAUNCH TECH. CO., LTD. All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying and recording or otherwise, without the prior written permission of LAUNCH. The information contained herein is designed only for the use of this unit. LAUNCH is not responsible for any use of this information as applied to other units. i LAUNCH GEAR SCAN User's ManualEN General Notice Other product names used herein are for identification purposes only and may be trademarks of their respective owners. LAUNCH disclaims any and all rights in those marks. There is a possibility that this unit is inapplicable to some of the vehicle models or systems listed in the diagnosis section due to different countries, areas, and/or years. Do not hesitate to contact LAUNCH if you come across such questions. We are to help you solve the problem as soon as possible. Disclaimer To take full advantage of the unit, you should be familiar with the engine. All information, illustrations, and specifications contained in this manual are based on the latest information available at the time of publication. The right is reserved to make change at any time without notice. Neither LAUNCH nor its affiliates shall be liable to the purchaser of this unit or third parties for damages, losses, costs or expenses incurred by purchaser or third parties as a result of: accident, misuse, or abuse of this unit, or unauthorized modifications, repairs, or alterations to this unit, or failure to strictly comply with LAUNCH operating and maintenance instructions. LAUNCH shall not be liable for any damages or problems arising from the use of any options or any consumable products other than those designated as Original LAUNCH Products or LAUNCH Approved Products by LAUNCH. Safety Precautions and Warnings To prevent personal injury or damage to vehicles and/or the GEAR SCAN, please read this users manual first carefully and observe the following safety precautions at a minimum whenever working on a vehicle:

Always perform automotive testing in a safe environment. Do not attempt to operate or observe the tool while driving a vehicle. Operating or observing the tool will cause driver distraction and could cause a fatal accident. Wear safety eye protection that meets ANSI standards. Keep clothing, hair, hands, tools, test equipment, etc. away from all moving or hot engine parts. Operate the vehicle in a well-ventilated work area: Exhaust gases are poisonous. Put blocks in front of the drive wheels and never leave the vehicle unattended while running tests. ii LAUNCH GEAR SCAN User's Manual Use extreme caution when working around the ignition coil, distributor cap, ignition wires and spark plugs. These components create hazardous voltages when the engine is running. Put the transmission in P (for A/T) or N (for M/T) and make sure the parking brake is engaged. Keep a fire extinguisher suitable for gasoline/chemical/ electrical fires nearby. Dont connect or disconnect any test equipment while the ignition is on or the engine is running. Keep the GEAR SCAN dry, clean, free from oil/water or grease. Use a mild detergent on a clean cloth to clean the outside of the GEAR SCAN, when necessary. Please use the DC 5V power adaptor to charge the GEAR SCAN. No responsibility can be assumed for any damage or loss caused as a result of using power adaptors other than the right one. Warning:

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. The device has been evaluated to meet general RF exposure requirement. The SAR limit of USA (FCC) is 1.6 W/kg averaged over one gram of tissue. Device types Professional Diagnostic Tool with model GEAR SCAN has also been tested against this SAR limit. The highest reported SAR values for body-worn is 1.49 W/kg. This device was tested for typical body-worn operations with the back of the handset kept 0mm from the body. The use of accessories that do not satisfy these requirements may not comply with FCC RF exposure requirements, and should be avoided. iii LAUNCH GEAR SCAN User's ManualEN Table of Contents 1. Introduction ............................................................................................. 1 2. General Information ............................................................................... 2 2.1 On-Board Diagnostics (OBD) II ..................................................................... 2 2.2 Diagnostic Trouble Codes (DTCs) ................................................................. 2 2.3 Location of the Data Link Connector (DLC)................................................... 3 2.4 OBD II Readiness Monitors ........................................................................... 4 2.5 OBD II Monitor Readiness Status.................................................................. 5 2.6 OBD II Definitions .......................................................................................... 5 3. Product Descriptions ............................................................................. 7 3.1 Outline of GEAR SCAN ................................................................................. 7 3.2 Technical Specifications ................................................................................ 9 3.3 Accessories Checklist .................................................................................... 9 4. Initial Use............................................................................................... 10 4.1 Charging GEAR SCAN ................................................................................ 10 4.2 Getting Started ............................................................................................ 10 4.3 Job Menu ..................................................................................................... 12 5. Diagnose ............................................................................................... 14 5.1 Connection .................................................................................................. 14 5.2 System Diagnosing...................................................................................... 14 5.2.1 Smart Diagnosis (Auto-Detect) ............................................................ 14 5.2.2 Manual Diagnosis ................................................................................ 16 5.3 OBDII Diagnosis .......................................................................................... 23 5.4 History ......................................................................................................... 26 5.5 Resetting ..................................................................................................... 27 6. Update ................................................................................................... 28 7. Data ........................................................................................................ 29 7.1 Diagnostic Record ....................................................................................... 29 7.2 Diagnostic Report ........................................................................................ 30 7.3 DTC Library ................................................................................................. 30 7.4 DLC(Data Link Connector) Location............................................................ 31 7.5 Image........................................................................................................... 31 iv LAUNCH GEAR SCAN User's Manual 7.6 Feedback ..................................................................................................... 31 7.7 Firmware Fix ................................................................................................ 31 7.8 User Manual ................................................................................................ 31 8. Settings ................................................................................................. 32 8.1 Units of measurement ................................................................................. 32 8.2 Automatic detection on connect................................................................... 32 8.3 Display & Brightness ................................................................................... 32 8.4 Sound .......................................................................................................... 32 8.5 Network ....................................................................................................... 32 8.6 Date/Time .................................................................................................... 32 8.7 Language..................................................................................................... 32 8.8 Email Setup ................................................................................................. 33 8.9 Recovery ..................................................................................................... 33 8.10 Version....................................................................................................... 33 8.11 About .......................................................................................................... 33 9. FAQ ........................................................................................................ 34 v LAUNCH GEAR SCAN User's ManualEN 1. Introduction GEAR SCAN is an evolutionary smart solution for passenger car diagnosis. It inherits from LAUNCHs advanced diagnosing technology and is characterized by covering a wide range of vehicles, featuring powerful functions, and providing precise test result. GEAR SCAN has the following functions and advantages:

Smart(Auto-Detect) Diagnosis: Once GEAR SCAN and the vehicle are properly connected, the system starts auto-detect process. Once the whole process is successfully finished, a diagnostic report will be automatically generated and sent to your email box (if bound). Manual Diagnosis: If Auto-Detect failure occurs, manual diagnosis is also available. Diagnosis functions include: Version Information, Read DTCs, Clear DTCs and Read Data Stream (supports 3 display modes: Value, Graph and Merged). OBDII/EOBD Diagnosis: 10 modes of OBD II test are supported, including EVAP, O2 Sensor, I/M Readiness, MIL Status, VIN Info, and On-board monitors testing etc. Remote Diagnosis (optional): This option aims to help repair shops or technicians launch instant messaging and remote diagnosis, making the repair job getting fixed faster. Reset: Frequently used maintenance and reset items including Oil lamp reset, DPF regeneration, Electronic parking brake reset, Steering angle calibration, IMMO service, Battery maintenance system reset, ABS bleeding can be done. One-click Update: Let you update your diagnostic software and APK online. Diagnostic History: This function provides a quick access to the tested vehicles and users can choose to view the test report or resume from the last operation, without the necessity of starting from scratch. Diagnostic Feedback: Use this option to submit the vehicle issue to us for analysis and troubleshooting. DTC Library: Allows you to retrieve the definition of the diagnostic trouble code from the abundant DTC database. Displays battery real-time voltage once properly connected to the vehicle. Features screenshot capture. Screenshots and reports sharing are supported. Touch & Keypad input are supported. Quick Dial buttons enables you to easily access the corresponding functions. Moreover, GEAR SCAN also features a GEAR+ future community platform for promotion and advertisement pushing, software subscription and other information releasing. 1 LAUNCH GEAR SCAN User's ManualEN 2. General Information 2.1 On-Board Diagnostics (OBD) II The first generation of On-Board Diagnostics (OBD I) was developed by the California Air Resources Board (ARB) and implemented in 1988 to monitor some of the emission control components on vehicles. As technology evolved and the desire to improve the On-Board Diagnostic system increased, a new generation of On-Board Diagnostic system was developed. This second generation of On-

Board Diagnostic regulations is called OBD II. The OBD II system is designed to monitor emission control systems and key engine components by performing either continuous or periodic tests of specific components and vehicle conditions. When a problem is detected, the OBD II system turns on a warning lamp (MIL) on the vehicle instrument panel to alert the driver typically by the phrase of Check Engine or Service Engine Soon. The system will also store important information about the detected malfunction so that a technician can accurately find and fix the problem. Here below follow three pieces of such valuable information:

1) Whether the Malfunction Indicator Light (MIL) is commanded on or off;

2) Which, if any, Diagnostic Trouble Codes (DTCs) are stored;

3) Readiness Monitor status. 2.2 Diagnostic Trouble Codes (DTCs) OBD II Diagnostic Trouble Codes are codes that are stored by the on-board computer diagnostic system in response to a problem found in the vehicle. These codes identify a particular problem area and are intended to provide you with a guide as to where a fault might be occurring within a vehicle. OBD II Diagnostic Trouble Codes consist of a five-digit alphanumeric code. The first character, a letter, identifies which control system sets the code. The second character, a number, 0-3; other three characters, a hex character, 0-9 or A-F provide additional information on where the DTC originated and the operating conditions that caused it to set. Here below is an example to illustrate the structure of the digits:

2 LAUNCH GEAR SCAN User's Manual Figure 2-1 2.3 Location of the Data Link Connector (DLC) The DLC (Data Link Connector or Diagnostic Link Connector) is typically a 16-

pin connector where diagnostic code readers interface with the vehicles on-

board computer. The DLC is usually located 12 inches from the center of the instrument panel (dash), under or around the drivers side for most vehicles. If Data Link Connector is not located under dashboard, a label should be there telling location. For some Asian and European vehicles, the DLC is located behind the ashtray and the ashtray must be removed to access the connector. If the DLC cannot be found, refer to the vehicles service manual for the location. 3 LAUNCH GEAR SCAN User's ManualEN Figure 2-2 2.4 OBD II Readiness Monitors An important part of a vehicles OBD II system is the Readiness Monitors, which are indicators used to find out if all of the emissions components have been evaluated by the OBD II system. They are running periodic tests on specific systems and components to ensure that they are performing within allowable limits. Currently, there are eleven OBD II Readiness Monitors (or I/M Monitors) defined by the U.S. Environmental Protection Agency (EPA). Not all monitors are supported in every vehicles and the exact number of monitors in any vehicle depends on the motor vehicle manufacturers emissions control strategy. Continuous Monitors -- Some of the vehicle components or systems are continuously tested by the vehicles OBD II system, while others are tested only under specific vehicle operating conditions. The continuously monitored components listed below are always ready:

1. Misfire 2. Fuel System 3. Comprehensive Components (CCM) Once the vehicle is running, the OBD II system is continuously checking the above components, monitoring key engine sensors, watching for engine misfire, and monitoring fuel demands. Non-Continuous Monitors -- Unlike the continuous monitors, many emissions and engine system components require the vehicle to be operated under specific conditions before the monitor is ready. These monitors are termed non-

continuous monitors and are listed below:

1) EGR System 2) O2 Sensors 3) Catalyst 4) Evaporative System 5) O2 Sensor Heater 4 LAUNCH GEAR SCAN User's Manual 6) Secondary air Injection 7) Heated Catalyst 8) A/C system 2.5 OBD II Monitor Readiness Status OBD II systems must indicate whether or not the vehicles PCMs monitor system has completed testing on each component. Components that have been tested will be reported as Ready, or Complete, meaning they have been tested by the OBD II system. The purpose of recording readiness status is to allow inspectors to determine if the vehicles OBD II system has tested all the components and/or systems. The Powertrain Control Module (PCM) sets a monitor to Ready or Complete after an appropriate drive cycle has been performed. The drive cycle that enables a monitor and sets readiness codes to Ready varies for each individual monitor. Once a monitor is set as Ready or Complete, it will remain in this state. A number of factors, including erasing of Diagnostic Trouble Codes

(DTCs) with a code reader or a disconnected battery, can result in Readiness Monitors being set to Not Ready. Since the three continuous monitors are constantly evaluating, they will be reported as Ready all of the time. If testing of a particular supported non-continuous monitor has not been completed, the monitor status will be reported as Not Complete or Not Ready. In order for the OBD monitor system to become ready, the vehicle should be driven under a variety of normal operating conditions. These operating conditions may include a mix of highway driving and stop and go, city type driving, and at least one overnight-off period. For specific information on getting your vehicles OBD monitor system ready, please consult your vehicle owners manual. 2.6 OBD II Definitions Powertrain Control Module (PCM) -- OBD II terminology for the on-board computer that controls engine and drive train. Malfunction Indicator Light (MIL) -- Malfunction Indicator Light (Service Engine Soon, Check Engine) is a term used for the light on the instrument panel. It is to alert the driver and/or the repair technician that there is a problem with one or more of vehicles systems and may cause emissions to exceed federal standards. If the MIL illuminates with a steady light, it indicates that a problem has been detected and the vehicle should be serviced as soon as possible. Under certain conditions, the dashboard light will blink or flash. This indicates a severe problem and flashing is intended to discourage vehicle operation. The vehicle onboard diagnostic system cannot turn the MIL off until the necessary repairs are completed or the condition no longer exists. 5 LAUNCH GEAR SCAN User's ManualEN DTC -- Diagnostic Trouble Codes (DTC) that identifies which section of the emission control system has malfunctioned. Enabling Criteria -- Also termed Enabling Conditions. They are the vehicle-

specific events or conditions that must occur within the engine before the various monitors will set, or run. Some monitors require the vehicle to follow a prescribed drive cycle routine as part of the enabling criteria. Drive cycles vary among vehicles and for each monitor in any particular vehicle. Please refer to the vehicles factory service manual for specific enabling procedures. OBD II Drive Cycle -- A specific mode of vehicle operation that provides conditions required to set all the readiness monitors applicable to the vehicle to the ready condition. The purpose of completing an OBD II drive cycle is to force the vehicle to run its onboard diagnostics. Some form of a drive cycle needs to be performed after DTCs have been erased from the PCMs memory or after the battery has been disconnected. Running through a vehicles complete drive cycle will set the readiness monitors so that future faults can be detected. Drive cycles vary depending on the vehicle and the monitor that needs to be reset. For vehicle specific drive cycle, consult the service manual. Freeze Frame Data -- When an emissions related fault occurs, the OBD II system not only sets a code but also records a snapshot of the vehicle operating parameters to help in identifying the problem. This set of values is referred to as Freeze Frame Data and may include important engine parameters such as engine RPM, vehicle speed, air flow, engine load, fuel pressure, fuel trim value, engine coolant temperature, ignition timing advance, or closed loop status. Fuel Trim (FT) - Feedback adjustments to the base fuel schedule. Short-term fuel trim refers to dynamic or instantaneous adjustments. Long-term fuel trim refers to much more gradual adjustments to the fuel calibration schedule than short-term trim adjustments. These long-term adjustments compensate for vehicle differences and gradual changes that occur over time. 6 LAUNCH GEAR SCAN User's Manual 3. Product Descriptions 3.1 Outline of GEAR SCAN Figure 3-1 Name Descriptions Indicates test results. A quick dial to Read I/M readiness.

*Note: This function only applies to Diagnose. No. 1 2 LCD I/M 7 LAUNCH GEAR SCAN User's ManualEN 3 4 5 6 7 8 9 Auto VIN Detect Update Return HOME

/

/

Press it to quickly launch the auto VIN detection module.

*Note: To detect more and accurate VINs, a stable network connection is highly recommened for this function. A quick access to the Update module.

*Note: This function requires a stable network connection. Exit the current program or return to the previous screen. Press to the home(Job menu) screen. Move cursor up and down for selection. Move cursor left or right for selection; Or turn page up and down when more than one page is displayed. OBD-16 connector 5V Charging port To connect to external DC power for charging To connect to vehicle's DLC (Data Link Connector) via diagnostic cable. GEAR SCAN. In Off mode, press it for about 5 seconds to turn the handset on. 10 Power In On mode:

Press it to activate the LCD if the LCD is off. Press it to turn off the LCD if the LCD lights up. Press it for 3 seconds to turn it off. 11 12 13 OK Confirms a selection (or action) from a menu list. Screenshots Press it once to capture the current screen. All screenshots are saved in the Image folder of Data. Diagnostic Reports A quick dial to the Diagnostic Reports module. Alternatively, it can also be accessed by Data ->

Diagnostic Report. 8 LAUNCH GEAR SCAN User's Manual 14 15 Help Provides detailed descriptions/tips for diagnostics. Charging LED Red means Charging and Green means Fully charged. 3.2 Technical Specifications Screen: 5 IPS touch screen RAM: 1G ROM: 8GB Battery: 4000mAh rechargeable Li-battery OBDII input voltage range: 9~18V Touch & Keypad input Charging via:

DC 5V charging cable or Diagnostic cable through connection to vehicles DLC Dimension: 248.7mm x 93.5mm x 36mm Net weight: 530g Working temperature: -10 to 50C (14 to 122 F) Storage temperature: -20 to 70C (-4 to 158 F) 3.3 Accessories Checklist For detailed accessory items, please consult from the local agency or check the packing list supplied with GEAR SCAN together. 1. GEAR SCAN handset 2. OBD II diagnostic cable 3. DC 5V charging cable 4. User manual 5. Padded carrying case 9 LAUNCH GEAR SCAN User's ManualEN 4. Initial Use 4.1 Charging GEAR SCAN There are two charging methods available:

Via Charging Cable: Plug one end of the included charging cable into the DC-IN port of the tool, and the other end to the external DC power. Via Diagnostic Cable: Insert one end of the diagnostic cable into the DB-15 connector of the tool, and the other end to the vehicles DLC. Once the charging LED illuminates solid green, it indicates that the battery is fully charged. 4.2 Getting Started If it is the first time you have used this tool, you need to make some system settings. 1. Press the [Power] button to power it on. 2. The screen displays a welcome page. Tap Start to go to next step. 10 Figure 4-1 LAUNCH GEAR SCAN User's Manual 3. Choose the desired system language, and tap Next. 4. Choose the desired time zone, and tap Next to enter the WLAN setup page. 5. Slide the switch to ON, the system starts searching for all available wireless LANs. Choose the desired WLAN access point / network, If the network you chose is open, you can connect directly;

If the selected network is encrypted, you have to enter the right security key (network password).

*Note: If you choose Ignore in WLAN setup, it will go into the date setting page. If the tool has been properly connected to the Internet, the system will automatically obtain the correct network date and time and navigate to step 6. 6. After the network connection is done, tap Next to configure email address. Input the email address, and tap Next to navigate to the Job menu. Figure 4-2

*Note: You are strongly recommended to fill in the valid email address. Once you configured this option, the system will automatically send the diagnostic report to your email box every time a complete Auto-Detect process is successfully finished. 11 LAUNCH GEAR SCAN User's ManualEN 4.3 Job Menu It mainly includes the following function modules. Figure 4-3 Diagnose To configures GEAR SCAN to operate as a diagnostic tool. OBD II Reset Update This option presents a quick way to check for DTCs, isolate the cause of the illuminated Malfunction Indicator Lamp (MIL), check monitor status prior to emissions certification testing, verify repairs, and perform a number of other services that are emission-related. To perform common repair & maintenance items, including ABS bleeding, DPF regeneration and oil lamp reset etc. To update vehicle diagnostic software and APK.

*Note: This function requires a stable network connection. 12 LAUNCH GEAR SCAN User's Manual Data Settings Includes Diagnostic report, Diagnostic record, Feedback and Image etc. To make some system settings, including Network setup, Email and Brightness etc. GEAR+

(Coming soon) An add-on module for function extension, including Promotion message pushing and Software subscription etc. 13 LAUNCH GEAR SCAN User's ManualEN 5. Diagnose 5.1 Connection 1. Turn the ignition off. 2. Locate vehicles DLC socket: It provides standard 16 pins and is generally located on drivers side, about 12 inches away from the center of dashboard. See Figure 2-2. If DLC is not equipped under dashboard, a label indicating its position will be given. In case no DLC is found, please refer to Automobile Repair Manual. 3. Plug one end of the diagnostic cable into the DB-15 connector of GEAR SCAN, and tighten the captive screws. Connect the other end to the vehicles DLC. GEAR SCAN Vehicle's DLC Diagnostic Cable Figure 5-1 5.2 System Diagnosing This function is specially designed to diagnose electronic control systems of single vehicle model. 14 LAUNCH GEAR SCAN User's Manual 5.2.1 Smart Diagnosis (Auto-Detect) After connection, turn the ignition key on and the system enters auto-detect mode.

*Note: To detect more and accurate VINs, a stable network connection is highly recommended for this function.

*CAUTION: Dont connect or disconnect any test equipment with ignition on or engine running. A. Once the system successfully obtains the VIN (Vehicle Identification Number) information of the currently identified vehicle, it will continue scanning the vehicle systems. After the scanning is complete, a diagnostic report will be automatically generated and sent to your email box (if bound). B. If the tool failed to access the VIN information, the screen will display as below:

Fig. 5-2 Input the VIN, and tap OK, the system will automatically identify the vehicle model. If the vehicle VIN is successfully decoded, it will perform auto-

diagnosis until a diagnostic report is automatically output. Otherwise it will enter manual diagnosis mode. For details on manual diagnosis, see Chapter 5.2.2.

*Notes:

The most recognizable location for this number is in the top left corner on the vehicles dashboard. Other locations include the drivers door or post, and the 15 LAUNCH GEAR SCAN User's ManualEN firewall under the hood. In general, vehicle identification numbers are standardized - all contain 17 characters. VIN characters may be capital letters A through Z and numbers 1 through 0; however, the letters I, O and Q are never used in order to avoid mistakes of misreading. No signs or spaces are allowed in the VIN. 5.2.2 Manual Diagnosis If the tool can not obtain the VIN information, you can also perform vehicle diagnosis manually. In this mode, you need to execute the menu-driven command and then follow the on-screen instruction to proceed.

*Notes:

Before diagnosing, please make sure the diagnostic program corresponding to certain vehicle model has been installed on your GEAR SCAN. For vehicles manufactured by different vendors, it is possible that it has different diagnostic menus. For details, please follow the instructions on the screen to proceed. Refer to the flowchart illustrated as below to diagnose a vehicle manually:

Select Diagnose Read version information Read fault code Clear fault code Read data stream Select Vehicle Manufacturer Select test function Select Vehicle Model

(Note: For different vehicles, vehicle make selection may differ. Generally, we can choose a vehicle via make year. But for BENZ, we need to choose it via chassis.) Select test system Automatic

(Note: This mode allows your tool to scan the vehicle test system automatically) 16 Manual Select

(Note: In this case, you need to choose the desired system manually. Just follow the on-screen instructions to proceed.) LAUNCH GEAR SCAN User's Manual Take Demo as an example to demonstrate how to diagnose a vehicle. 1). Select diagnostic software version: Tap the DEMO to go to Step 2. Fig. 5-3 Fig. 5-4 2). Select test item: Select the desired test item to proceed. Fig. 5-5 5.2.2.1 Health Report (Quick Test) This function varies from vehicle to vehicle. It enables you to quickly access all the electronic control units of the vehicle and generate a detailed report about vehicle health. 17 LAUNCH GEAR SCAN User's ManualEN Tap Health Report, the system starts scanning the ECUs. Once the scanning is complete, a screen similar to the following appears:

Fig. 5-6 In above figure, the tested system with fault code appears in red and the system with OK displays in white (normally). On-screen Buttons:

: Tap to display the details of DTCs existing in the current system. Tap hide it. Enter: Tap to select other test functions. For detailed operations, refer to Chapter 5.2.2.3 System Selection. Report: Tap to save the diagnostic result as a report. Clear DTC: Tap to clear the existing diagnostic trouble codes. to 5.2.2.2 System Scan This option allows you to quickly scan which systems are installed on the vehicle. 5.2.2.3 System Selection This option allows you manually select the test system and function step by step. 18 LAUNCH GEAR SCAN User's Manual In Fig. 5-5, tap System Selection, the screen displays as follows:

Tap the desired system (take ECM for example) to jump to the test function page. Fig. 5-7 Fig. 5-8

*Note: Different vehicle has different diagnostic menus. A. Version Information This function is used to read the version information of system mode, vehicle VIN, software and ECU. B. Read Fault Code This function displays the detailed information of DTC records retrieved from the 19 LAUNCH GEAR SCAN User's ManualEN vehicles control system. In Fig. 5-8, tap Read DTC, the screen will display the diagnostic result. Fig. 5-9 On-screen Buttons:

Freeze Frame: When an emission-related fault occurs, certain vehicle conditions are recorded by the on-board computer. This information is referred to as freeze frame data. Freeze frame data includes a snapshot of critical parameter values at the time the DTC is set. Help: Tap to view the help information. Code Search: Tap it to search for more information about the current DTC online. Report: To save the current data in text format. All diagnostic reports can be accessed from Data -> Diagnostic Report. C. Clear Fault Memory After reading the retrieved codes from the vehicle and certain repairs have been carried out, you can use this function to erase the codes from the vehicle. Before performing this function, please be sure the vehicles ignition key is in the ON position with the engine off.

*Note: The trouble code will not disappear until the trouble was completely cleared. 20 LAUNCH GEAR SCAN User's Manual D. Read Data Stream This option retrieves and displays live data and parameters from the vehicles ECU. In Fig. 5-8, tap Read Data Stream, the system will display data stream items. Fig. 5-10 On-screen Buttons:

Select All: Tap it to select all items of the current page. To select certain data stream item, just check the box before the item name. Unselect: Tap it to deselect all data stream items. OK: Tap it to confirm and jump to the next step. After selecting the desired items, tap OK to enter the data stream reading page. 21 LAUNCH GEAR SCAN User's ManualEN Fig. 5-11

*Notes:

1. If the value of the data stream item is out of the range of the standard (reference) value, the whole line will display in red. If it complies with the reference value, it displays in blue (normal mode). 2. The indicator 1/X shown on the bottom of the screen stands for the current page/

total page number. Swipe the screen from the right/left to advance/return to the next/previous page. There are 3 types of display modes available for data viewing, allowing you to view various types of parameters in the most suitable way. Value this is the default mode which displays the parameters in texts and shows in list format. Graph displays the parameters in waveform graphs. Combine this option is mostly used in graph merge status for data comparison. In this case, different items are marked in different colors. On-screen Buttons:

: Tap it to view the waveform graph of the current data stream item. 22 LAUNCH GEAR SCAN User's Manual Fig. 5-12 Combine: Tap it, a pull-down list of the data stream items appears on the screen. Select the necessary items and the screen will display the waveforms corresponding to these items immediately. Report: To save the current data as a diagnostic report. All diagnostic reports can be accessed from Data -> Diagnostic Report. Record: Tap to start recording diagnostic data for future playback and analysis. The saved file follows the naming rule: It begins with vehicle type, and then the record starting time and ends with .x431 (To differentiate between files, please configure the accurate system time). All diagnostic records can be replayed from Data -> Diagnostic Record. 5.3 OBDII Diagnosis This option presents a quick way to check for DTCs, isolate the cause of the illuminated Malfunction Indicator Lamp (MIL), check monitor status prior to emissions certification testing, verify repairs, and perform a number of other services that are emission-related. On the Job menu, press [OBD II] to enter system, the screen will automatically jump to figure 5-13:

23 LAUNCH GEAR SCAN User's ManualEN Figure 5-13 Figure 5-14 Tap [OK], a screen similar to Figure 5-14 will appear. It mainly includes the following functions:

1. Read Codes This option is used to identify which section of the emission control system has malfunctioned. 2. Erase Codes After reading the retrieved codes from the vehicle and certain repairs have been carried out, you can use this function to erase the codes from the vehicle. Before performing this function, please be sure the vehicles ignition key is in the ON position with the engine off.

*Notes:

Before performing this function, make sure to retrieve and record the trouble codes. After clearing, you should retrieve trouble codes once more or turn ignition on and retrieve codes again. If there are still some trouble codes in the system, please troubleshoot the code using a factory diagnosis guide, then clear the code and recheck. 24 LAUNCH GEAR SCAN User's Manual 3. I/M Readiness I/M refers to Inspection and Maintenance that is legislated by the Government to meet federal clean-air standards. I/M Readiness indicates whether or not the various emissions-related systems on the vehicle are operating properly and are ready for Inspection and Maintenance testing. The purpose of the I/M Readiness Monitor Status is to indicate which of the vehicles Monitors have run and completed their diagnosis and testing (as described in Chapter 2.5), and which ones have not yet run and completed testing and diagnosis of their designated sections of the vehicles emissions system. The I/M Readiness Monitor Status function also can be used (after repair of a fault has been performed) to confirm that the repair has been performed correctly, and/or to check for Monitor Run Status. 4. Data Stream This option retrieves and displays live data and parameters from the vehicles ECU. 5. View Freeze Frame When an emission-related fault occurs, certain vehicle conditions are recorded by the on-board computer. This information is referred to as freeze frame data. Freeze Data is a snapshot of the operating conditions at the time of an emission-

related fault.

*Note: If DTCs were erased, Freeze Data may not be stored in vehicle memory depending on vehicle. 6. O2 sensor test The results of O2 sensor test are not live values but instead the results of the ECUs last O2 sensor test. For live O2 sensor readings, refer to any of the live sensor screens such as Graph Screen. Not all test values are applicable to all vehicles. Therefore, the list generated will vary depending on vehicle. In addition, not all vehicles support the Oxygen Sensors screen. 7. On-board monitor test This function can be utilized to read the results of on-board diagnostic monitoring tests for specific components/systems. 8. EVAP System Test The EVAP test function lets you initiate a leak test for the vehicles EVAP system. The GEAR SCAN does not perform the leak test, but signals to vehicles on-

25 LAUNCH GEAR SCAN User's ManualEN board computer to initiate the test. Before using the system test function, refer to the vehicles service repair manual to determine the procedures necessary to stop the test. 9. Vehicle Info This option displays the vehicle information, such as VIN (Vehicle Identification Number), CID (Calibration ID) and CVN (Calibration Verification Number). 5.4 History Generally once a vehicle diagnosis is performed, GEAR SCAN will record the every details of diagnostic session. The History function provides direct access to the previously tested vehicles and users can resume from the last operation, without the necessity of starting from scratch. Tap History on the Manual Diagnosis main menu screen, all diagnostic records will be listed on the screen in date sequence. Fig. 5-15 Tap certain vehicle model to view the details of the last diagnostic report. To delete certain diagnostic history, select it and then tap Delete. To delete all historical records, tap Select All and then tap Delete. 26 LAUNCH GEAR SCAN User's Manual Tap Quick access to directly navigate to the function selection page of last diagnostic operation. Choose the desired option to proceed. 5.5 Resetting In addition to amazing & powerful diagnostic function, GEAR SCAN also features Oil / Service lamp reset etc. There are two methods to reset service lamp: Manual reset or Auto reset. Auto reset follows the principle of sending command from GEAR SCAN to vehicles ECU to do resetting. While using manual reset, users just follow the on-screen instructions to select appropriate execution options, enter correct data or values, and perform necessary actions, the system will guide you through the complete performance for various service operations. Follow the flowchart shown as below to perform resetting. Select "Reset"

Choose the desired service function (e.g. oil lamp reset etc.) Select the desired car brand Select the reset mode (The available mode varies from vehicle to vehicle) Follow the on-screen instructions to proceed 27 LAUNCH GEAR SCAN User's ManualEN 6. Update If some new software or APK can be updated, a numeric indicator will display on the Upgrade module on the Job menu. In this case, you may use this option to keep it synchronized with the latest version.

*Notes:

To enjoy more functions and better service, you are strongly suggested to update it on regular basis. This function requires a stable network connection. Tap Upgrade on the Job menu to enter the update center. By default, all diagnostic software is selected. To deselect certain software, tap Unselect, and then check the box next to vehicle model. Tap Update to start downloading. It may take several minutes to finish it, please be patient to wait. To pause downloading, tap Stop. To resume it, tap Continue. If network connection failure occurs, tap Retry to try again. Once download is finished, the software packages will be installed automatically. 28 LAUNCH GEAR SCAN User's Manual 7. Data Fig. 7-1 7.1 Diagnostic Record If user records the running parameters or waveform graphs while reading data stream, it will be saved as diagnostic records and appear under this tab. Tap Diagnostic Record to enter and select the desired data stream items and tap OK to jump to the playback page. On-screen Buttons:

Graph displays the parameters in waveform graphs. Combine this option is mostly used in graph merge status for data comparison. In this case, different items are marked in different colors. Value this is the default mode which displays the parameters in texts and shows in list format. Frame Playback plays back the recorded data stream items frame by frame. Once it is in frame playback mode, this button changes into Auto Playback. 29 LAUNCH GEAR SCAN User's ManualEN 7.2 Diagnostic Report This module stores all diagnostic reports generated in process of vehicle diagnosis. All the diagnostic reports are sorted by Date and Make. If there are too many reports stored, tap To select certain report, just check the box at the right lower corner of the

(Search) to filter and quickly locate it. report. To select all reports, tap Select All. To deselect all, tap Unselect. Tap it to view its details. Select the desired report and then tap Delete to delete it. 7.3 DTC Library This option helps you to find the location of the vehicles DLC. Swipe the screen upwards/downwards to alter the value, then press [OK] button, the screen will display definition of the DTC. Fig. 7-2 30 LAUNCH GEAR SCAN User's Manual 7.4 DLC(Data Link Connector) Location This option helps you to find the location of the vehicles DLC. 7.5 Image This option enables you to manage the screenshots. 7.6 Feedback This item allows you to feedback your diagnostic problems to us for analysis and troubleshooting. Tap Feedback, the following 3 options will be displayed on the left column of the screen. A. Feedback Tap a tested vehicle model to enter the feedback screen. 1) Tap Choose File to open the target folder and choose the desired diagnostic logs. 2) Choose the failure type and fill in the detailed failure description in the blank text box and telephone or email address. After inputting, tap Submit Result to send it to us. B. History Tap it to view all diagnostic feedback records. Different process states are marked with different colors. C. Offline list Tap it to display all diagnostic feedback logs which have not been submitted successfully due to network failure. Once the handset gets a stable network signal, it will be uploaded to the remote server automatically. 7.7 Firmware Fix Use this item to upgrade and fix diagnostic firmware. During fixing, please do not cut power or switch to other interfaces. 7.8 User Manual Provides a detailed description on how to operate the GEAR SCAN. Before operating the handset, please carefully read it. 31 LAUNCH GEAR SCAN User's ManualEN 8. Settings 8.1 Units of measurement It is designed to set the measurement unit. Metric System and English System are available. 8.2 Automatic detection on connect This option enables you to determine whether to start an automatic VIN detection once GEAR SCAN is properly connected to the vehicles DLC. 8.3 Display & Brightness This item allows you to set the standby time and screen brightness.

*Tips: Reducing the brightness of the screen is helpful to conserve the power of the handset. 8.4 Sound This option lets you adjust the volume and other sound settings. 8.5 Network

*Note: Once WLAN is set as ON, GEAR SCAN will consume more power. While it keeps unused, please set it off to save power. While WLAN keeps unused, please turn it off to conserve battery power. GEAR SCAN has built-in WLAN module that can be used to get online. Once youre online, you can register your tool, update diagnostic software & APK, send email on your network. Slide the switch to ON, the system starts searching for all available wireless LANs. Choose the desired WLAN access point / network to connect. 8.6 Date/Time This option allows you to set the system date & time.

*Note: Since all diagnostic reports are sorted by Make and Date. To differentiate between files, please configure the accurate system time. 8.7 Language GEAR SCAN supports multiple languages. You can use this option to change the target language. 32 LAUNCH GEAR SCAN User's Manual 8.8 Email Setup This option is used to set up the default email address for automatically receiving the diagnostic reports. 8.9 Recovery Use this item to reset this tool to the default factory setting.

*Warning: Resetting may cause data loss. Before doing so, please be careful to perform this operation. 8.10 Version BOOT, Download, App and System version are included. 8.11 About This option displays the hardware configuration information of the tool and license agreement. 33 LAUNCH GEAR SCAN User's ManualEN 9. FAQ Here we list some frequently asked questions and answers related to GEAR SCAN. 1 System halts when reading data stream. What is the reason?

It may be caused by a slackened connector. Please turn off the GEAR SCAN, firmly connect the connector, and switch it on again. 2 Screen of main unit flashes at engine ignition start. Caused by electromagnetic disturbing, and this is normal phenomenon. 3 There is no response when communicating with on-board computer. Please confirm the proper voltage of power supply and check if the throttle has been closed, the transmission is in the neutral position, and the water is in proper temperature. 4 What to do if the system fails to start auto VIN detection?

Please check the following possible reasons:

Whether GEAR SCAN is properly connected to the vehicles DLC. Whether the Automatic detection on Connect switch is OFF. If yes, slide it to ON. 5 Why are there so many fault codes?

Usually, its caused by poor connection or fault circuit grounding. 34 LAUNCH GEAR SCAN User's Manual Warranty THIS WARRANTY IS EXPRESSLY LIMITED TO PERSONS WHO PURCHASE LAUNCH PRODUCTS FOR PURPOSES OF RESALE OR USE IN THE ORDINARY COURSE OF THE BUYERS BUSINESS. LAUNCH electronic product is warranted against defects in materials and workmanship for one year (12 months) from date of delivery to the user. This warranty does not cover any part that has been abused, altered, used for a purpose other than for which it was intended, or used in a manner inconsistent with instructions regarding use. The exclusive remedy for any automotive meter found to be defective is repair or replacement, and LAUNCH shall not be liable for any consequential or incidental damages. Final determination of defects shall be made by LAUNCH in accordance with procedures established by LAUNCH. No agent, employee, or representative of LAUNCH has any authority to bind LAUNCH to any affirmation, representation, or warranty concerning LAUNCH automotive meters, except as stated herein. Order Information Replaceable and optional parts can be ordered directly from your LAUNCH authorized tool supplier. Your order should include the following information:

1. Quantity 2. Part number 3. Item description Customer Service If you have any questions on the operation of the unit, please contact local dealer, or contact LAUNCH Tech(USA), Inc.:

LAUNCH Tech(USA) Product Support Service & Repair Phone: 877-528-6249 xt: 4 Fax: 562-463-1590 1820 S. Milliken Ave. Ontario, CA 91761 Monday - Friday 5 am - 5 pm PST Phone: 877-528-6249 xt: 5 Monday - Friday 8 am - 5 pm PST Please visit our public form @

http://launch.activeboard.com Statement: LAUNCH reserves the rights to make any change to this manual without notice. We have tried our best to make the descriptions and illustrations in the manual as accurate as possible, and defects are inevitable, if you have any question, please contact local dealer or LAUNCH Tech(USA), Inc., LAUNCH does not bear any responsibility arising from misunderstandings. 35 LAUNCH GEAR SCAN User's ManualEN

Appendix WTS18S05110779W_Photo EUT External View Model GEAR SCAN FCC ID: 2APTR-GEARSCAN Page 3 of 16 Appendix WTS18S05110779W_Photo Page 4 of 16 Appendix WTS18S05110779W_Photo Page 5 of 16 Appendix WTS18S05110779W_Photo Page 6 of 16 Appendix WTS18S05110779W_Photo Page 7 of 16

FCC Label Location for model: GEAR SCAN

FCC Label Sample for model: GEAR SCAN

Launch Tech (USA) Inc. Date: 5/14/2018 FEDERAL COMMUNICATIONS COMMISSION AUTHORIZATION AND EVALUATION DIVISION 7435 OAKLAND MILLS ROAD COLUMBIA, MD 21046 We, the undersigned hereby declare, that the following radio equipment:

Applicant : Launch Tech (USA) Inc. Address: 1820 South Milken Ave., Ontario, CA 91761 Product name: Professional Diagnostic Tool Model : GEAR SCAN FCCID : 2APTR-GEARSCAN Freq Range: 2412MHz ~ 2462MHz is electrically equal to the original equipment:

Applicant Launch Tech Co., Ltd. Address _: Launch Industrial Park, North of Wuhe Rd. Banxuegang, Longgang, Shenzhen, China Product name: Professional Diagnostic Tool Model(s) : CRP.429_CRP 429C, CRP 423, CRP 808, CRP 818, CRP 828, Pilot Scan FCCID _: XUJCRP429 Date of Grant: 2018/05/03, Freq Range : 2412MHz ~ 2462MHz Except the product model number had changed, the EUT are electronically/electrically identical to the original equipment and that the original test results continue to be representative of and applicable to it. The new product version is identical to the certified product. And the document on-file with FCC from the original certification, remain unchanged and continue to be valid. BEST REGARDS, Launch Tech (USA) Inc. Eric Le

Launch Tech Co., Ltd. Date: May 22, 2018 FEDERAL COMMUNICATIONS COMMISSION AUTHORIZATION AND EVALUATION DIVISION 7435 OAKLAND MILLS ROAD COLUMBIA, MD 21046 SUBJECT: FCC ID: (Original FCC ID #XUJCRP429 Product name: Professional Diagnostic Tool Model (s) : CRP 429 CRP 429C, CRP 423, CRP 808, CRP 818, CRP 828, Pilot Scan TO WHOM IT MAY CONCERN:

BEING THE APPLICANT FOR THE ABOVE MENTIONED FCC IDENTIFIER, WE HEREBY AUTHORIZE Launch Tech (USA) Inc. AT 1820 South Milliken Ave., Ontario, CA 91761 TO APPLY FOR FCC MULTIPLE LISTING FOR THEIR PRODUCT: Professional Diagnostic Tool MODEL: GEAR SCAN, FCC ID : 2APTR-GEARSCAN WILL BE. THEY WISH TO MARKET THIS PRODUCT UNDER THEIR OWN COMPANY NAME. And authorization them to utilized documents on-file with FCC from the existing certification. BEST REGARDS, Launch Tech Co., Ltd.

Launch Tech (USA) Inc. ECC ID: 2APTR-GEARSCAN POWER OF ATTORNEY Date: 5/14/2018 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 To Whom It May Concern:

We, the undersigned, hereby authorize Waltek Services (ShenZhen) Co., Ltd.

(Philo Zhong) on our behalf, to apply to the Federal Communications Commission on our equipment. Any and all acts carried out by Waltek Services (ShenZhen) Co., Ltd. (Philo Zhong) on our behalf shall have the same effect as acts of our own. This authorization expires on 5/13/2019. This is to advise that we are in full compliance with the Anti-Drug Abuse Act. We, Launch Tech (USA) Inc., are not subject to a denial of federal benefits pursuant to Section 5301 of the Anti-Drug Act of 1988, 21 USC853a, and no party to the application is subject to a denial of federal benefits pursuant to that section. Sincerely, Launch Tech (USA) Inc. 2B Eric Wang /manager Signatu:

Typed name and Title