all | frequencies |
|
exhibits | applications |
---|---|---|---|---|
manual |
app s | submitted / available | |||||||
---|---|---|---|---|---|---|---|---|
1 |
|
Users Manual | Users Manual | 3.68 MiB | September 11 2017 / August 05 2018 | |||
1 | Cover Letter(s) | September 11 2017 | ||||||
1 | External Photos | September 11 2017 / August 05 2018 | ||||||
1 | ID Label/Location Info | September 11 2017 | ||||||
1 | Internal Photos | September 11 2017 / August 05 2018 | ||||||
1 | RF Exposure Info | September 11 2017 | ||||||
1 | RF Exposure Info | September 11 2017 | ||||||
1 | RF Exposure Info | September 11 2017 | ||||||
1 | Test Setup Photos | September 11 2017 / August 05 2018 | ||||||
1 | Test Report | September 11 2017 |
1 | Users Manual | Users Manual | 3.68 MiB | September 11 2017 / August 05 2018 |
INSTRUCTION MANUAL DBu Digital Belt Pack Transmitter Fill in for your records:
Serial Number:
Purchase Date:
Rio Rancho, NM, USA www.lectrosonics.com 2 DBuLECTROSONICS, INC. Table of Contents Introduction .............................................................................................................................................................................................4 Frequency Agility...................................................................................................................................................................................4 DSP-controlled Input Limiter .................................................................................................................................................................4 DBu Block Diagram ...............................................................................................................................................................................5 Battery Installation .................................................................................................................................................................................6 Battery Status LED Indicator ................................................................................................................................................................6 Belt Clips ...............................................................................................................................................................................................7 Operating Instructions ...........................................................................................................................................................................7 IR (infrared) Port ...................................................................................................................................................................................7 Powering On in Operating Mode ...........................................................................................................................................................8 Powering Off .........................................................................................................................................................................................8 Power Menu Options ..............................................................................................................................................................................8 Entering the Power Menu ......................................................................................................................................................................8 LCD Menu Map ........................................................................................................................................................................................9 Main Menu and Setup Screen Details .................................................................................................................................................10 Entering the Main Menu ......................................................................................................................................................................10 Main Window Indicators .....................................................................................................................................................................10 Connecting the Signal Source ............................................................................................................................................................10 Adjusting the Input Gain ......................................................................................................................................................................10 Selecting Frequency ...........................................................................................................................................................................11 Selecting Programmable Switch Functions.........................................................................................................................................11 Selecting the Low Frequency Roll-off .................................................................................................................................................11 Selecting Audio Polarity (Phase) .........................................................................................................................................................11 Selecting Battery Type ........................................................................................................................................................................11 BatTime ...............................................................................................................................................................................................11 Restoring Default Settings ..................................................................................................................................................................12 Wipekey ..............................................................................................................................................................................................12 Whip Antennas ....................................................................................................................................................................................12 Encryption Key and Settings Transfer ...............................................................................................................................................12 Accessories ..........................................................................................................................................................................................13 5-Pin Input Jack Wiring ........................................................................................................................................................................14 Microphone Cable Termination for Non-Lectrosonics Microphones .............................................................................................................................................15 Input Jack Wiring for Different Sources .............................................................................................................................................16 Compatible Wiring for Both Servo Bias Inputs and Earlier Transmitters: ............................................................................................16 Simple Wiring for Servo Bias Inputs ONLY: .........................................................................................................................................16 Microphone RF Bypassing ..................................................................................................................................................................17 Line Level Signals ...............................................................................................................................................................................17 Firmware Update ..................................................................................................................................................................................18 Troubleshooting ....................................................................................................................................................................................20 Specifications .......................................................................................................................................................................................21 Service and Repair ...............................................................................................................................................................................22 Returning Units for Repair ..................................................................................................................................................................22 Consumer Alert for US Users - FCC Order DA 10-92 Most users do not need a license to operate this wireless microphone system. Nevertheless, operating this micro-
phone system without a license is subject to certain restrictions: the system may not cause harmful interference; it must operate at a low power level (not in excess of 50 milliwatts); and it has no protection from interference received from any other device. Purchasers should also be aware that the FCC is currently evaluating use of wireless mi-
crophone systems, and these rules are subject to change. For more information, call the FCC at 1-888- CALL-FCC
(TTY: 1-888-TELL-FCC) or visit the FCCs wireless microphone website at www.fcc.gov/cgb/wirelessmicrophones. To operate wireless microphone systems at power greater than 50mW, you must qualify as a Part 74 user and be licensed. If you qualify and wish to apply for a license go to: http://www.fcc.gov/Forms/Form601/601.html 3 Digital Belt-Pack TransmitterRio Rancho, NM Introduction The DBu transmitter is a second generation design with specially developed, high efficiency digital circuitry for extended operating time on two AA batteries. The trans-
mitter can tune in coarse or fine steps across the UHF television band from 470.100 to 607.975 MHz, with an output power of 50 mW. The pure digital architecture enables AES 256-CTR encryption for high level security applications. Studio quality audio performance is assured by high quality components in the preamp, wide range input gain adjustment and DSP-controlled limiting. Input connections and settings are included for any lavaliere microphone, dynamic microphones and line level inputs. Input gain is adjustable over a 44 dB range in 1 dB steps to allow an exact match to the input signal level, to maximize the dynamic range and signal to noise ratio. A separate switch is provided on the top panel that can be configured as a mute or power switch, or bypass. The housing is constructed of solid machined aluminum for lasting ruggedness. The exterior is finished with an ultra hard, black electroless nickel finish called ebENi. Firmware updates are made through a side panel micro USB port. Frequency Agility The transmitter tunes across the entire frequency range, from 470.100 MHz to 607.975 MHz. Servo Bias Input and Wiring The DBu input preamp is a unique design that delivers audible improvements over conventional transmitter inputs, is easier to use and much harder to overload. It is not necessary to introduce pads on some mics to prevent overload of the input stage, divide the bias voltage down for some low voltage mics, or reduce the limiter range at minimum gain settings. Two different microphone wiring schemes are available to simplify and standardize the configuration. Simpli-
fied 2-wire and 3-wire configurations provide several arrangements designed for use only with servo bias inputs to take full advantage of the preamp circuitry. Other wiring schemes are compatible with Servo Bias and conventional inputs. A line level input wiring provides an extended frequency response with an LF roll-off at 35 Hz for use with instru-
ments and line level signal sources. DSP-controlled Input Limiter The transmitter employs a digitally-controlled analog audio limiter prior to the analog-to-digital converter. The limiter has a range greater than 30 dB for excellent overload protection. A dual release envelope makes the limiter acoustically transparent while maintaining low distortion. It can be thought of as two limiters in series, connected as a fast attack and release limiter followed by a slow attack and release limiter. The limiter recovers quickly from brief transients, so that its action is hidden from the listener, but recovers slowly from sustained high levels to keep audio distortion low and preserve short term dynamic changes in the audio. 4 DBuLECTROSONICS, INC. DBu Block Diagram
+5V Input Jack Servo Bias Supply Bias Voltage 0, 2 or 4V Input Preamp HI/Lo Pass Filter Audio DBu Transmitter A-D Converter D-A Convert-
er Gain Adj I2S I2S I + Q Baseband Signals Low pass filters
(2) AA Batteries Shunt Limiter Limiter Control l k c o C P S D Key Received Blue LED Microprocessor Keypad Firmware Update UART Security Key Oscillator VCTXO 36.864 mHz PLL Ref Phase Locked Loop Voltage Controlled Oscillator Control Switching Power Supply Power LED Tricolor IR Port USB Jack Low Pass Filter IQ Modulator Buffer Filters Final Amplifier 5 Digital Belt-Pack TransmitterRio Rancho, NM Battery Installation The transmitter is powered by two AA batteries. We recommend using alkaline, lithium, or rechargeable bat-
teries for longest life. The battery status circuitry compensates for the differ-
ence in voltage drop between alkaline and lithium bat-
teries across their usable life, so its important to select the correct battery type in the menu. Because rechargeable batteries run down quite abrupt-
ly, using the Power LED to verify battery status will not be reliable. However, it is possible to track battery status using the battery timer function available in the receiver. Push outward on the battery compartment door and lift it to open. Slide door out to release catch Lift door to open Insert the batteries according to the markings on the back of the housing. If the batteries are inserted incorrectly, the door will close but the unit will not operate. The battery contacts can be cleaned with alcohol and a cotton swab, or a clean pencil eraser. Be sure not to leave any remnants of the cotton swab or eraser crumbs inside the compartment. Contact springs Battery Status LED Indicator Alkaline, lithium or rechargeable batteries can be used to power the transmitter. The type of batteries in use are selectable in a menu on the LCD. When alkaline or lithium batteries are being used, the LED labeled BATT on the keypad glows green when the batteries are good. The color changes to red when the they are nearing the end of life. When the LED begins to blink red, there will be only a few minutes remaining. The Power/Function LED on the top panel will mirror the keypad LED unless the programmable switch is set to Mute, and the switch is turned on. The exact point at which the LEDs turn red will vary with battery brand and condition, temperature and power consumption. The LEDs are intended to simply catch your attention, not to be an exact indicator of remaining time. A weak battery will sometimes cause the Power LED to glow green immediately after the transmitter is turned on, but it will soon discharge to the point where it will turn red or the unit will turn off completely. Rechargeable batteries give little or no warning when they are depleted. If you wish to use these batteries in the transmitter, the most accurate way to determine runtime status is by testing the time provided by a par-
ticular battery brand and type, then using the BatTime function to determine remaining runtime. NOTE: Refer to the Main Menu and Setup Section for BatTime details. 6 DBuLECTROSONICS, INC. Operating Instructions Modulation Indicators*
IR Port Programmable Function Switch Antenna Port
-20 AUDIO
-10 IR PORT PWR/FUNC Battery status LED Belt clip mounting hole Battery compartment door Return to previous screen Audio Input Jack DBu 470.100
-40
-20
+0 u Full access to all settings is provided through the key-
pad and LCD. The transmitter can also be configured as a one button device by locking the ability to make changes with the keypad, and configuring the top panel switch as either power on/off or a mute function. Key verification LED Belt clip mounting hole USB Port Menu navigation buttons Power button
*When the transmitter is set to MUTE, the -10 Modula-
tion Indicators LED will glow solid red. Otherwise, the
-10 Modulation Indicators LED will glow solid green when transmitter is on. Belt Clips The wire belt clip may be removed by pulling the ends out of the holes in the sides of the case. Use pliers to grasp the wire and avoid scratching the surface of the housing. Pliers also help when installing the clip. An optional spring-loaded, hinged belt clip (model num-
ber BCSLEBN) is also available. This clip is attached by removing the plastic hole cap on the back of the hous-
ing and mounting the clip with the supplied screw. IR (infrared) Port The IR port is available on the top of the transmitter for quick setup using a receiver with this function avail-
able. IR Sync will transfer the settings for frequency from the receiver to the transmitter. 7 Digital Belt-Pack TransmitterRio Rancho, NM Powering On in Operating Mode for several seconds Press and hold the Power Button until a counter on the LCD progresses from 1 through 3. Power Menu Options Entering the Power Menu Press the power button once briefly from any menu or screen and a menu will appear with several options. Use the arrow buttons to highlight menu items. Then press MENU/SEL to execute the item or enter a setup screen. The following options are available:
and Resume - returns to the previous mode and screen Pwr Off - turns the unit off irrevocably Rf On? - enters a screen to enable the operating or standby modes AutoOn? - allows the unit to automatically turn back on after a power failure or when fresh batter-
ies are installed (works in the operating mode only) Backlit - adjusts the duration of the LCD back light to 30 seconds or 5 minutes, or to remain on About - displays model number and firmware version DBu V1.03 Hold for Rf On
...3 DBu 470.100
-40
-20
+0 When you release the button, the unit will be operation-
al with the RF output turned on and the Main Window displayed. Powering On in Standby Mode A brief press of the Power Button
, releasing it before the counter has reached 3, will turn the unit on with the RF output turned off. In this Standby Mode the menus can be browsed to make settings and adjustments with-
out the risk of interfering with other wireless systems nearby. Hold for Rf On
...1 Release Power Button before the counter reaches 3 to enter standby mode RF indicator blinks DBu 470.100
-40
-20
+0 After settings and adjustments are made, press the power button again to turn the unit off. NOTE: Also see the section entitled Power Menu for the AutoOn feature. Powering Off Powering O . 1 From any screen, power can be turned off by selecting Pwr Off in the power menu, holding the Power Button in and waiting for the countdown, or with the program-
mable switch (if it is configured for this function). If the power button is released, or the top panel switch is turned back on again before the countdown is com-
pleted, the unit will remain turned on and the LCD will return to the same screen or menu that was displayed previously. NOTE: If the programmable switch is in the OFF position, power can still be turned on with the power button. If the programmable switch is then turned on, a brief message will appear on the LCD. 8 DBuLECTROSONICS, INC. LCD Menu Map Gain SEL BACK Gain 22 Use arrow buttons to select value Level meter at bottom of screen Freq. SEL Freq. BACK 470.675 Press MENU/SEL to highlight MHz or kHz Select value with arrow buttons NOTE: The settings will be stored when the BACK button is pressed. ProgSw SEL BACK
(none) Mute Power Select option with arrow buttons Rolloff SEL BACK Rolloff 50 Hz Select value with arrow buttons Phase SEL BACK Phase Normal Invert Select option with arrow buttons BatType SEL BACK BatTime SEL BACK TxPower SEL BACK Locked?
SEL BACK Default SEL BACK BatType Alk. Lith. Bat 5:41 Reset?
Yes No TxPower 25 mW 50 mW Locked?
Yes No Default Settings No Yes Select option with arrow buttons Select option with arrow buttons Select option with arrow buttons Select option with arrow buttons Select option with arrow buttons WipeKey SEL BACK WipeKey?
No Yes Select option with arrow buttons 9 Digital Belt-Pack TransmitterRio Rancho, NM Main Menu and Setup Screen Details Entering the Main Menu The LCD and keypad interface makes it easy to browse the menus and make the selections for the setup you need. When the unit is powered up in either the oper-
ating or the standby mode, press MENU/SEL on the keypad to enter a menu structure on the LCD. Use the arrow buttons to select the menu item. Then press the MENU/SEL button to enter the setup screen. and Gain Freq. ProgSw Rolloff Gain 25
-40
-20 0 The prompt in the upper right corner may display one or both arrows, depending upon what adjustment can be made. If the changes are locked, a small padlock symbol will appear. Main Window Indicators The Main Window displays programmable switch func-
tion, Standby or Operating mode, operating frequency, audio level and battery status. Programmable Switch Function Frequency (MHz) DBu MUTE 470.100
-40
-20
+0 Operating mode Battery status Audio level If the programmable switch function is set for Mute, the Main Window will indicate that the function is enabled. Mute function enabled but not active DBu MUTE 470.100
-40
-20
+0 When the switch is turned on, the mute icon appear-
ance will change and the word MUTE will blink at the bottom of the display. The -10 LED on the top panel will also glow solid red. Connecting the Signal Source Microphones, line level audio sources and instruments can be used with the transmitter. Refer to the section entitled Input Jack Wiring for Different Sources for details on the correct wiring for line level sources and microphones to take full advantage of the Servo Bias circuitry. Adjusting the Input Gain The two bicolor Modulation LEDs on the top panel pro-
vide a visual indication of the audio signal level entering the transmitter. The LEDs will glow either red or green to indicate modulation levels as shown in the following table. Signal Level Less than -20 dB
-20 dB to -10 dB
-10 dB to +0 dB
+0 dB to +10 dB Greater than +10 dB Off Green Green Red Red Off Off Green Green Red
-20 LED
-10 LED NOTE: Full modulation is achieved at 0 dB, when the -20 LED first turns red. The limiter can cleanly handle peaks up to 30 dB above this point. It is best to go through the following procedure with the transmitter in the standby mode so that no audio will en-
ter the sound system or recorder during adjustment. 1) With fresh batteries in the transmitter, power the unit on in the standby mode (see previous section Powering On in Standby Mode). 2) Navigate to the Gain setup screen. Gain Freq. ProgSw Rolloff Gain 25
-40
-20 0 3) Prepare the signal source. Position a microphone the way it will be used in actual operation and have the user speak or sing at the loudest level that oc-
cur during use, or set the output level of the instru-
ment or audio device to the maximum level that will be used. 4) Use the arrow buttons to adjust the gain until the 10 dB glows green and the 20 dB LED starts to flicker red during the loudest peaks in the audio. and Main Window will blink the word MUTE when the audio is muted 5) Once the audio gain has been set, the signal can be sent through the sound system for overall level adjustments, monitor settings, etc. DBu MUTE 470.100
<MUTE>
10 DBuLECTROSONICS, INC. 6) If the audio output level of the receiver is too high or low, use only the controls on the receiver to make adjustments. Always leave the transmitter gain ad-
justment set according to these instructions, and do not change it to adjust the audio output level of the receiver. Selecting Audio Polarity (Phase) Audio polarity can be inverted at the transmitter so the audio can be mixed with other microphones without comb filtering. The polarity can also be inverted at the receiver outputs. Selecting Frequency The setup screen for frequency selection offers two ways to browse the available frequencies. Freq. Freq. Phase BatType BatTime TxPower Phase Normal Invert 494.500 494.500 Selecting Battery Type Gain Freq. ProgSw Rolloff and Press the MENU/SEL button to select each field. Use the Each field will step through the available frequencies in a different increment. arrow buttons to adjust the frequency. Selecting Programmable Switch Functions The programmable switch on the top panel can be con-
figured using the menu to provide several functions:
(none) - disables the switch Mute - mutes the audio when switched on; LCD will blink a message and -10 LED will glow solid red. Power - turns the power on and off Gain Freq. ProgSw Rolloff ProgSw
(none) Mute Power and Use the arrow buttons to select the desired function or disable the switch NOTE: The programmable switch will continue to operate whether or not keypad changes are locked. Selecting the Low Frequency Roll-off The low frequency audio roll-off is adjustable to op-
timize performance for ambient noise conditions or personal preference. Low frequency audio content may be desirable or distracting, so the point at which the roll-off takes place can be set to 35, 50, 70, 100, 120 and 150 Hz. Gain Freq. ProgSw Rolloff Rolloff 70 Hz The voltage drop over the life of different batteries var-
ies by type and brand. Be sure to set the correct battery type for accurate indications and warnings. The menu offers alkaline or lithium types. Phase BatType BatTime TxPower BatType Alk. Lith. If you are using rechargeable batteries, it is better to use the timer function on the receiver to monitor the battery life rather than the indicators on the transmitter. Rechargeable batteries maintain a fairly constant volt-
age across the operating time on each charge and stop working abruptly, so you will have little or no warning as they reach the end of operation. BatTime A built-in timer can be used with any battery type, but it is especially valuable with rechargeable batteries such as NiMH types. The voltage remains fairly constant across the discharge time of a rechargeable battery, then drops quickly near the end of the operating time. The most accurate way to determine runtime status is by testing the time provided by a particular battery brand and type, then using the timer to determine re-
maining runtime. Rechargeable batteries lose capacity over their life, so it is good to run the battery down and note the runtime on older or unfamiliar batteries. Phase BatType BatTime TxPower Bat 3:30 Reset?
No Yes Bat 0:00 Reset?
No Yes 11 Digital Belt-Pack TransmitterRio Rancho, NM Whip Antennas Because the transmitter tunes across such a broad fre-
quency range, it is best to use the appropriate antenna for maximum operation. Three antennas are included with the transmitter, and are shipped from the factory pre-cut and fully assembled. Each antenna covers three blocks. Use the chart below to determine which antenna best fits your needs. Frequency Cap Block Range MHz Color Antenna 470 19 20 21 22 23 470.100 - 495.600 486.400 - 511.900 512.000 - 537.500 537.600 - 563.100 563.200 - 588.700 588.800 - 614.300 Black Black Black Red Red Red AMM19 AMM19 AMM19 AMM22 AMM22 AMM22 Encryption Key and Settings Transfer A cable between the receiver and the micro USB port on the side of the transmitter is used to transfer the encryption key from the receiver to the transmitter. This connection can also be used to send the transmitter settings stored in the receiver to the transmitter. The interface cable, P/N DRKEYCABLE, is used to make this connection. Setting Transmitter Output Power The output power can be set to 25 mW or 50 mW. Phase BatType BatTime TxPower TxPower 25 mW 50 mW Locking/Unlocking Changes to Settings Changes to the settings can be locked to prevent inad-
vertent changes being made. BatType BatTime TxPower Locked?
Locked?
Gain 25 Yes No
-40
-20 0 A small padlock symbol will appear on adjustment screens when changes have been locked. When changes are locked, several controls and actions can still be used:
Settings can still be unlocked Menus can still be browsed Programmable switch still works (Mute and On/Off) Power can still be turned off by using the power menu or removing the batteries. Restoring Default Settings This is used to restore the factory settings. Backlit About Default Wipekey Default settings No Yes Wipekey The encryption key can be erased with this setup screen. NOTE: Reference the DSW System Instruction Manual for instructions on Encryption Key settings and software. Backlit About Default Wipekey WipeKey?
No Yes 12 DBuLECTROSONICS, INC. Accessories P/N 26895 Wire belt clip with very high output pickups; right angle 1/4 plug BCSLEBN Spring-loaded belt clip MI33PST Instrument cable; passive type for use with very high output pickups; straight 1/4 plug DRKEYCABLE Encryption key and settings transfer cable; micro USB to male 3.5 mm TRS; 42 in. length MC35 Line level adapter cable; XLR-F to TA5F; 37 length M152/5P 700 Lavaliere microphone; omnidirectional MC41 Dynamic mic level adapter cable;
XLR-F to TA5F; 37 length MI33PRA Instrument cable; passive type for use 13 Digital Belt-Pack TransmitterRio Rancho, NM 5-Pin Input Jack Wiring The wiring diagrams included in this section represent the basic wiring necessary for the most common types of microphones and other audio inputs. Some micro-
phones may require extra jumpers or a slight variation on the diagrams shown. It is virtually impossible to keep completely up to date on changes that other manufacturers make to their products, thus you may encounter a microphone that differs from these instructions. If this occurs please call our toll-free number listed under Service and Repair in this manual or visit our web site at:
www.lectrosonics.com
+5 VDC 1 2 3 4 5 GND 5V SOURCE MIC VOLTAGE SELECT LINE IN m h O 0 0 5 100 Ohm k 1
+
15uF Servo Bias Pin 4 to Pin 1 = 0 V Pin 4 Open = 2 V Pin 4 to Pin 2 = 4 V 200 Ohm 30uF
+
+
3.3uF 10k K 7
. 2 To Audio Amplifier To Limiter Control Backshell with strain relief TA5F Latchlock Insert Insulator Cable clamp Audio input jack wiring:
PIN 1 Shield (ground) for positive biased electret lavaliere microphones. Shield (ground) for dynamic microphones and line level inputs. PIN 2 Bias voltage source for positive biased electret lavaliere microphones that are not using servo bias circuitry and voltage source for 4 volt servo bias wiring. PIN 3 Microphone level input and bias supply. PIN 4 Bias voltage selector for Pin 3. Pin 3 voltage depends on Pin 4 connection. PIN 5 Line level input for tape decks, mixer outputs, musical instruments, etc. Pin 4 tied to Pin 1: 0 V Pin 4 Open: 2 V Pin 4 to Pin 2: 4 V Remove strain relief if using dust boot Dust boot (35510) Backshell without strain relief Note: If you use the dust boot, remove the rubber strain relief that is attached to the TA5F cap, or the boot will not fit over the assembly. 6) If necessary, remove the rubber strain relief from the TA5F backshell by simply pulling it out. 7) Seat the insulator on the insert. Slide the cable clamp over the and of the insulator and crimp as shown on the next page. 8) Insert the assembled insert/insulator/clamp into the latchlock. Make sure the tab and slot align to allow the insert to fully seat in the latchlock. Thread the backshell onto the latchlock. Installing the Connector:
1) If necessary, remove the old connector from the microphone cable. 2) Slide the dust boot onto microphone cable with the large end facing the connector. 3) If necessary, slide the 1/8-inch black shrink tubing onto the microphone cable. This tubing is needed for some smaller diameter cables to ensure there is a snug fit in the dust boot. 4) Slide the backshell over the cable as shown above. Slide the insulator over the cable before soldering the wires to the pins on the insert. 5) Solder the wires and resistors to the pins on the insert according to the diagrams shown in Input Jack Wiring for Different Sources. A length of
.065 OD clear tubing is included if you need to insulate the resistor leads or shield wire. 14 DBuLECTROSONICS, INC. Microphone Cable Termination for Non-Lectrosonics Microphones TA5F Connector Assembly Mic Cord Stripping Instructions 1 5 4 2 3 VIEW FROM SOLDER SIDE OF PINS 0.15"
0.3"
Crimping to Shield and Insulation Strip and position the cable so that the clamp can be crimped to contact both the mic cable shield and the insulation. The shield contact reduces noise with some microphones and the insulation clamp increases ruggedness. Shield Insulation Crimp these fingers to contact the shield Crimp these fingers to clamp the insulation NOTE: This termination is intended for UHF transmitters only. VHF transmitters with 5-pin jacks require a different termination. Lectrosonics lavaliere microphones are terminated for compatibility with VHF and UHF transmitters, which is different from what is shown here. 15 Digital Belt-Pack TransmitterRio Rancho, NM Input Jack Wiring for Different Sources In addition to the microphone and line level wiring illus-
trated below, Lectrosonics makes a number of cables and adapters for other situations such as connecting musical instruments (guitars, bass guitars, etc.) to the transmitter. Visit www.lectrosonics.com and click on Accessories, or download the master catalog. A lot of information regarding microphone wiring is also available in the FAQ section of the web site at:
www.lectrosonics.com > SUPPORT > FAQs Follow the instructions to search by model number or other search options. Compatible Wiring for Both Servo Bias Inputs and Earlier Transmitters:
Fig. 1 2 VOLT POSITIVE BIAS 2-WIRE ELECTRET SHIELD A UDI O 3.3 k Compatible wiring for microphones such as Countryman E6 headworn and B6 lavaliere. Fig. 2 4 VOLT POSITIVE BIAS 2-WIRE ELECTRET 1.5 k PIN 1 2 3 4 5 4 3 5 1 2 T A5 F PLUG Most common type of wiring for lavaliere mics. Fully compatible with 5-pin inputs on Lectrosonics transmitters such as the LM and UM Series. Fig. 3 DPA MICROPHONES (Danish Pro Audio miniature models) PIN 1 2 3 4 5 4 3 5 1 2 T A5 F PLUG This wiring is for DPA lavalier and headset microphones. NOTE: The resistor value can range from 3k to 4k ohms. Fig. 4 2 VOLT NEGATIVE BIAS 2-WIRE ELECTRET 2.7 k SHIELD AUDIO Compatible wiring for microphones such as negative bias TRAM models. NOTE: The resistor value can range from 2k to 4k ohms. Fig. 5 4 VOLT POSITIVE BIAS 3-WIRE ELECTRET WITH EXTERNAL RESISTOR Used for 3-wire lavaliere microphones that require an external resistor such as the Sanken COS-11. SHIELD DRAIN (BIAS) SOURCE (AUDIO) This wiring is fully compatible with 5-pin inputs on Lectrosonics transmitters such as the LM and UM Series. This is the wiring for the Lectrosonics M152 lavaliere microphone. Fig. 6 LO-Z MICROPHONE LEVEL SIGNALS XLR JACK For low impedance dynamic mics or electret mics with internal battery or power supply. Insert 1k resistor in series with pin 3 if attenuation is needed 16 Fig. 8 UNBALANCED LINE LEVEL SIGNALS SLEEVE SHIELD A UDI O LINE LEVEL RCA or 1/4 PLUG TIP PIN 1 2 3 4 5 4 3 5 1 2 T A5 F PLUG For signal levels up to 3V (+12 dBu) before limiting. Fully compatible with 5-pin inputs on other Lectrosonics transmitters such as the LM and UM Series. A 20k ohm resistor can be inserted in series with Pin 5 for an additional 20 dB of attenuation to handle up to 30V (+32 dBu). See Line Level Signals on next page Fig. 8 UNBALANCED LINE LEVEL SIGNALS SLEEVE SHIELD A UDI O LINE LEVEL RCA or 1/4 PLUG TIP For signal levels up to 3V (+12 dBu) before limiting. Fully compatible with 5-pin inputs on other Lectrosonics transmitters such as the LM and UM Series. A 20k ohm resistor can be inserted in series with Pin 5 for an additional 20 dB of attenuation to handle up to 30V (+32 dBu). PIN 1 2 3 4 5 4 3 5 1 2 T A5 F PLUG Simple Wiring for Servo Bias Inputs ONLY:
Fig. 9 2 VOLT POSITIVE BIAS 2-WIRE ELECTRET Simplified wiring for microphones such as Countryman B6 Lavalier and E6 Earset models and others. NOTE: This Servo Bias wiring is not compatible with earlier versions of Lectrosonics transmitters. Check with the factory to confirm which models can use this wiring. Fig. 10 2 VOLT NEGATIVE BIAS 2-WIRE ELECTRET Simplified wiring for microphones such as negative bias TRAM. NOTE: This Servo Bias wiring is not compatible with earlier versions of Lectrosonics transmitters. Check with the factory to confirm which models can use this wiring. Fig. 11 4 VOLT POSITIVE BIAS 3-WIRE ELECTRET NOTE: This Servo Bias wiring is not compatible with earlier versions of Lectrosonics transmitters. Check with the factory to confirm which models can use this wiring. DBuLECTROSONICS, INC. Microphone RF Bypassing Line Level Signals When used on a wireless transmitter, the microphone element is in the proximity of the RF coming from the transmitter. The nature of electret microphones makes them sensitive to RF, which can cause problems with microphone/transmitter compatibility. If the electret microphone is not designed properly for use with wire-
less transmitters, it may be necessary to install a chip capacitor in the mic capsule or connector to block the RF from entering the electret capsule. Some mics require RF protection to keep the radio sig-
nal from affecting the capsule, even though the trans-
mitter input circuitry is already RF bypassed. If the mic is wired as directed, and you are having dif-
ficulty with squealing, high noise, or poor frequency response, RF is likely to be the cause. The best RF protection is accomplished by installing RF bypass capacitors at the mic capsule. If this is not pos-
sible, or if you are still having problems, capacitors can be installed on the mic pins inside the TA5F connec-
tor housing. Refer to the diagram below for the correct locations of capacitors. Use 330 pF capacitors. Capacitors are available from Lectrosonics. Please specify the part number for the desired lead style. Leaded capacitors: P/N 15117 Leadless capacitors: P/N SCC330P All Lectrosonics lavaliere mics are already bypassed and do not need any additional capacitors installed for proper operation. The wiring for line level and instrument signals is:
Signal Hot to pin 5 Signal Gnd to pin 1 Pin 4 jumped to pin 1 This allows signal levels up to 3V RMS to be applied without limiting. NOTE for line level inputs only (not instrument):
If more headroom is needed, insert a 20 k resistor in series with pin 5. Put this resistor inside the TA5F connector to minimize noise pickup. The resistor will have little or no effect on the signal if the input is set for instrument. Line Level Normal Wiring Line Level More Headroom
(20 dB) See Fig. 8 on previous page 2-WIRE MIC Capacitors next to mic capsule SHIELD AUDIO CAPSULE 3-WIRE MIC SHIELD AUDIO TA5F CONNECTOR BIAS CAPSULE Capacitors in TA5F connector TA5F CONNECTOR 17 Digital Belt-Pack TransmitterRio Rancho, NM Firmware Update Updating the firmware is a simple matter of download-
ing a utility program and file from the website and running the program on a Windows operating system with the transmitter connected to a computer via the USB port. Go to www.lectrosonics.com/US. In the top menu, hover the mouse over Support, and click on Wireless Support. On the right-hand-side Wireless Support Menu, choose Wireless Downloads. Choose your product (DBu) then choose DB Firmware. Step 1:
Step 2:
Next, test the Updater by opening the icon:
driver opens automatically, proceed to Step 3. If the WARNING: If you receive the following error, the FTDI USB Device Driver is not installed on your system. Follow the TROUBLESHOOTING steps to fix the error. Begin by downloading the USB Firmware Updater Program. TROUBLESHOOTING:
If you receive the FTDI D2XX error shown above, download and install the driver by clicking on this link. Then click here to download. NOTE: This website, http://www.ftdichip.com/
Drivers/D2XX.htm, is not associated with Lectrosonics.com. It is a third party site used only for D2XX drivers currently available for Lectrosonics devices upgrades. 18 DBuLECTROSONICS, INC. Step 3:
Step 7:
Refer to Step 1 to return to Firmware web page. Down-
load Firmware Update and save to a local file on your PC for easy locating when updating. In Lectrosonics USB Firmware Updater, choose the detected device, browse to local Firmware File and click Start. NOTE: It may take up to a minute or so for the Updater to recognize the transmitter. Step 4:
Open Lectrosonics USB Firmware Updater. WARNING: Do not disrupt the microUSB cable during updating. Step 5:
UPDATE Step 6:
Put the transmitter in UPDATE mode by simultaneously holding down the UP and DOWN arrow buttons on the transmitter control panel while powering it up. Using a microUSB cable, connect the transmitter to your PC. The Updater alerts with progress and completion. Step 8:
DBu V1.03 Step 9:
Once the Updater has completed, turn off the transmitter, then turn it back on to verify that the firmware version on the transmitter LCD matches the firmware version shown on the web site. The firmware is the second LCD display during boot up sequence. Close Updater and disconnect microUSB cable. 19 Digital Belt-Pack TransmitterRio Rancho, NM Troubleshooting Symptom:
Transmitter Battery LED off when Power Switch ON It is important that you follow these steps in the sequence listed. Possible Cause:
1. Batteries are inserted incorrectly. 2. Batteries are low or dead. No Transmitter Modulation LEDs when Signal Should be Present 1. Gain control turned all the way down. 2. Batteries are inserted incorrectly. Check power LED. 3. Mic capsule is damaged or malfunctioning. 4. Mic cable damaged or miswired. 5. Instrument Cable damaged or not plugged in. 6. Musical instrument output level set too low. Receiver Indicates RF But No Audio Receiver RF Indicator Off using an alternate source or cable. 1. Audio source or cable connected to transmitter is defective. Try 2. Make sure the compatibility mode is the same on transmitter and 3. Ensure musical instrument volume control is not set to minimum. receiver. frequency, and that the hex code matches. 1. Ensure that the transmitter and receiver are set to the same 2. Transmitter not turned on, or battery is dead. 3. Receiver antenna missing or improperly positioned. 4. Operating distance is too great. 5. Transmitter may be set to the Standby Mode. See page 8. No Sound (Or Low Sound Level), Receiver Indicates Proper Audio Modulation 1. Receiver output level set too low. 2. Receiver output is disconnected; cable is defective or miswired. 3. Sound system or recorder input is turned down. Distorted Sound LEDs on transmitter and receiver while distortion is being heard. 1. Transmitter gain (audio level) is too high. Check Modulation 2. Receiver output level may be mismatched with the sound 3. RF interference. Reset both transmitter and receiver to a clear system or recorder input. Adjust output level on receiver to the correct level for the recorder, mixer or sound system. channel. Use scanning function on receiver if available. Wind Noise or Breath Pops 1. Reposition microphone, or use a larger windscreen, or both. 2. Omni-directional mics produce less wind noise and breath pops than directional types. Hiss and Noise -- Audible Dropouts 1. Transmitter gain (audio level) far too low. 2. Receiver antenna missing or obstructed. 3. Operating distance too great. 4. RF interference. Reset both transmitter and receiver to a 5. Musical instrument output set too low. 6. Microphone capsule picking up RF noise. See item on page 17 clear channel. Use scanning function on receiver if available. entitled Microphone RF Bypassing. Excessive Feedback (With Microphone) and/or reduce receiver output level. 1. Transmitter gain (audio level) too high. Check gain adjustment 2. Microphone too close to speaker system. 3. Microphone is too far from users mouth. 20 DBuLECTROSONICS, INC. 470.100 - 607.975 MHz 25 kHz Selectable; 25 or 50 mW 0.002%
8 PSK Specifications Frequency Range:
Frequency Selection:
Steps:
RF Power Output:
Frequency Stability:
Digital Modulation:
Equivalent Input Noise: 128 dBV Input Level:
Input Impedance:
Input Limiter:
Gain Control Range:
Modulation Indicators:
Controls:
Audio Input Jack:
Antenna:
Battery:
Battery Life:
Weight:
Dimensions:
Emission Designator: 200KG1E Nominal 2 mV to 300 mV, before limiting Greater than 1V maximum, with limiting. Mic: 300 Ohm Line: 2k Ohm Dual envelope type; 30 dB range 44 dB in 1 dB steps; digital control Dual bicolor LEDs indicate modulation of
-20, -10, 0 and +10 dB referenced to full modulation LCD bar graph interface for power on/off and all setup Top panel toggle switch;
programmable as power, mute or none
(off) function Side panel membrane switches with LCD and configuration controls Switchcraft 5-pin locking (TA5F) Galvanized steel, flexible wire Two AA Lithium recommended 5 hours; Lithium 6.24 ounces (177 grams), including two AA batteries and wire belt clip 3.2 x 2.5 x .74 in. (86 x 62 x 19 mm) Specifications subject to change without notice. For body worn operation, this transmitter model has been tested and meets the FCC RF exposure guidelines when used with the Lectrosonics accessories supplied or designated for this product. Use of other accessories may not ensure compliance with FCC RF exposure guidelines. Contact Lectrosonics if you have any questions or need more information about RF exposure using this product.. This device complies with FCC radiation exposure limits as set forth for an uncontrolled environment. This device should be installed and operated so that its antenna(s) are not co-located or operating in conjunction with any other antenna or transmitter. This device complies with ISED Canada radiation exposure limits as set forth for a controlled professional use only. Cet appareil est conforme avec les normes dIndustrie Canada concernant les limites dexposition aux radiations pour un usage professionnel contrl seulement. 21 Digital Belt-Pack TransmitterRio Rancho, NM Service and Repair If your system malfunctions, you should attempt to correct or isolate the trouble before concluding that the equipment needs repair. Make sure you have followed the setup procedure and operating instructions. Check the interconnecting cables and then go through the Troubleshooting section in this manual. We strongly recommend that you do not try to repair the equipment yourself and do not have the local repair shop at-
tempt anything other than the simplest repair. If the repair is more complicated than a broken wire or loose connection, send the unit to the factory for repair and service. Dont attempt to adjust any controls inside the units. Once set at the factory, the various controls and trimmers do not drift with age or vibration and never require readjustment. There are no adjustments inside that will make a malfunctioning unit start working. LECTROSONICS Service Department is equipped and staffed to quickly repair your equipment. In warranty repairs are made at no charge in accordance with the terms of the warranty. Out-of-warranty repairs are charged at a modest flat rate plus parts and shipping. Since it takes almost as much time and effort to determine what is wrong as it does to make the repair, there is a charge for an exact quotation. We will be happy to quote approximate charges by phone for out-of-warranty repairs. Returning Units for Repair For timely service, please follow the steps below:
A. DO NOT return equipment to the factory for repair without first contacting us by email or by phone. We need to know the nature of the problem, the model number and the serial number of the equipment. We also need a phone number where you can be reached 8 A.M. to 4 P.M. (U.S. Mountain Standard Time). B. After receiving your request, we will issue you a return authorization number (R.A.). This number will help speed your repair through our receiving and repair departments. The return authorization number must be clearly shown on the outside of the shipping container. C. Pack the equipment carefully and ship to us, shipping costs prepaid. If necessary, we can provide you with the proper packing materials. UPS is usually the best way to ship the units. Heavy units should be double-boxed for safe transport. D. We also strongly recommend that you insure the equipment, since we cannot be responsible for loss of or dam-
age to equipment that you ship. Of course, we insure the equipment when we ship it back to you. Lectrosonics USA:
Mailing address:
Lectrosonics, Inc. PO Box 15900 Rio Rancho, NM 87174 USA Web:
www.lectrosonics.com Lectrosonics Canada:
Mailing Address:
720 Spadina Avenue, Suite 600 Toronto, Ontario M5S 2T9 Shipping address:
Lectrosonics, Inc. 561 Laser Rd. NE, Suite 102 Rio Rancho, NM 87124 USA Telephone:
(505) 892-4501
(800) 821-1121 Toll-free
(505) 892-6243 Fax E-mail:
sales@lectrosonics.com service.repair@lectrosonics.com Telephone:
(416) 596-2202
(877) 753-2876 Toll-free
(877-7LECTRO)
(416) 596-6648 Fax E-mail:
Sales:
Service: joeb@lectrosonics.com colinb@lectrosonics.com 22 DBuLECTROSONICS, INC. 23 Digital Belt-Pack TransmitterRio Rancho, NM LIMITED ONE YEAR WARRANTY The equipment is warranted for one year from date of purchase against defects in materials or workmanship provided it was purchased from an authorized dealer. This warranty does not cover equipment which has been abused or damaged by careless handling or shipping. This warranty does not apply to used or demonstrator equipment. Should any defect develop, Lectrosonics, Inc. will, at our option, repair or replace any defective parts without charge for either parts or labor. If Lectrosonics, Inc. cannot correct the defect in your equipment, it will be replaced at no charge with a similar new item. Lectrosonics, Inc. will pay for the cost of returning your equipment to you. This warranty applies only to items returned to Lectrosonics, Inc. or an authorized dealer, shipping costs prepaid, within one year from the date of purchase. This Limited Warranty is governed by the laws of the State of New Mexico. It states the entire liablility of Lectrosonics Inc. and the entire remedy of the purchaser for any breach of warranty as outlined above. NEITHER LECTROSONICS, INC. NOR ANYONE INVOLVED IN THE PRODUCTION OR DELIVERY OF THE EQUIPMENT SHALL BE LIABLE FOR ANY INDIRECT, SPECIAL, PUNITIVE, CONSEQUENTIAL, OR INCIDENTAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THIS EQUIPMENT EVEN IF LECTROSONICS, INC. HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. IN NO EVENT SHALL THE LIABILITY OF LECTROSONICS, INC. EXCEED THE PURCHASE PRICE OF ANY DEFECTIVE EQUIPMENT. This warranty gives you specific legal rights. You may have additional legal rights which vary from state to state. 581 Laser Road NE Rio Rancho, NM 87124 USA www.lectrosonics.com
(505) 892-4501 (800) 821-1121 fax (505) 892-6243 sales@lectrosonics.com 03 October 2017
frequency | equipment class | purpose | ||
---|---|---|---|---|
1 | 2017-11-09 | 470.1 ~ 607.975 | TLD - Licensed LPAS Device | Original Equipment |
app s | Applicant Information | |||||
---|---|---|---|---|---|---|
1 | Effective |
2017-11-09
|
||||
1 | Applicant's complete, legal business name |
Lectrosonics Inc
|
||||
1 | FCC Registration Number (FRN) |
0007067481
|
||||
1 | Physical Address |
581 Laser Rd NE
|
||||
1 |
Rio Rancho, New Mexico 87124
|
|||||
1 |
United States
|
|||||
app s | TCB Information | |||||
1 | TCB Application Email Address |
b******@baclcorp.com
|
||||
1 | TCB Scope |
B2: General Mobile Radio And Broadcast Services equipment in the following 47 CFR Parts 22 (non-cellular) 73, 74, 90, 95, 97, & 101 (all below 3 GHz)
|
||||
app s | FCC ID | |||||
1 | Grantee Code |
DBZ
|
||||
1 | Equipment Product Code |
DBU
|
||||
app s | Person at the applicant's address to receive grant or for contact | |||||
1 | Name |
R******** C********
|
||||
1 | Title |
Vice President, Engineering
|
||||
1 | Telephone Number |
505-8********
|
||||
1 | Fax Number |
505-8********
|
||||
1 |
c******@lectrosonics.com
|
|||||
app s | Technical Contact | |||||
n/a | ||||||
app s | Non Technical Contact | |||||
n/a | ||||||
app s | Confidentiality (long or short term) | |||||
1 | Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | Yes | ||||
1 | Long-Term Confidentiality Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | Yes | ||||
1 | If so, specify the short-term confidentiality release date (MM/DD/YYYY format) | 05/08/2018 | ||||
if no date is supplied, the release date will be set to 45 calendar days past the date of grant. | ||||||
app s | Cognitive Radio & Software Defined Radio, Class, etc | |||||
1 | Is this application for software defined/cognitive radio authorization? | No | ||||
1 | Equipment Class | TLD - Licensed LPAS Device | ||||
1 | Description of product as it is marketed: (NOTE: This text will appear below the equipment class on the grant) | Digital Wireless Microphone Transmitter | ||||
1 | Related OET KnowledgeDataBase Inquiry: Is there a KDB inquiry associated with this application? | No | ||||
1 | Modular Equipment Type | Does not apply | ||||
1 | Purpose / Application is for | Original Equipment | ||||
1 | Composite Equipment: Is the equipment in this application a composite device subject to an additional equipment authorization? | No | ||||
1 | Related Equipment: Is the equipment in this application part of a system that operates with, or is marketed with, another device that requires an equipment authorization? | No | ||||
1 | Grant Comments | Power listed is conducted. SAR compliance with accessories for portable use conditions have been evaluated as described in this filing. The antenna(s) used for this transmitter must not transmit simultaneously with any other antenna or transmitter. The highest reported SAR value for Body-worn is 0.31 W/kg. | ||||
1 | Is there an equipment authorization waiver associated with this application? | No | ||||
1 | If there is an equipment authorization waiver associated with this application, has the associated waiver been approved and all information uploaded? | No | ||||
app s | Test Firm Name and Contact Information | |||||
1 | Firm Name |
Bay Area Compliance Laboratories Corporation
|
||||
1 | Name |
L****** T********
|
||||
1 | Telephone Number |
408-7******** Extension:
|
||||
1 | Fax Number |
408 7********
|
||||
1 |
l******@baclcorp.com
|
|||||
Equipment Specifications | |||||||||||||||||||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
1 | 1 | 74H | 470.1 | 607.975 | 0.05 | 50 ppm | 200KG1E | ||||||||||||||||||||||||||||||||||
1 | 2 | 74H | 470.1 | 607.975 | 0.025 | 50 ppm | 200KG1E |
some individual PII (Personally Identifiable Information) available on the public forms may be redacted, original source may include additional details
This product uses the FCC Data API but is not endorsed or certified by the FCC