FCC ID: DBZSMQE Wireless Microphone Transmitter

INSTRUCTION MANUAL SMa Series Super Miniature Belt-Pack Transmitters With Digital Hybrid Wireless Technology Single battery, 100 mW SMa SMDa Dual battery, 100 mW SMQa Dual battery, 250 mW RM Remote Control for SM Transmitters Fill in for your records:

Serial Number:

Purchase Date:

Digital Hybrid Wireless US Patent 7,225,135 Rio Rancho, NM, USA www.lectrosonics.com SMa Series 2 LECTROSONICS, INC. Thank you for selecting a Lectrosonics SM Series ultra-miniature transmitter. The unique design provides several distinct features for professional applications:

Outstanding RF operating range Superb audio quality Ultra-lightweight, corrosion resistant housing Water resistant seals for use in damp environments Programmable compatibility modes for use with a wide variety of different receivers The Digital Hybrid WirelessTM design (US Patent 7,225,135) combines 24-bit digital audio with analog FM resulting in a system that has the same operating range as analog systems, the same spectral efficiency as analog systems, the same long battery life as analog systems, plus the excellent audio fidelity typical of pure digital systems. The SM Series transmitters use a standard Lectroson-

ics 5-pin type input jack for use with electret lavaliere mics, dynamic mics, or line level signals. A water resistant control panel with LCD, membrane switches and multi-color LEDs make input gain adjustments and frequency and compatibility mode selection quick and accurate, without having to view the receiver. The bat-

tery compartment accepts AA lithium or rechargeable batteries. The SM is machined from a solid aluminum block to provide an extremely lightweight and rugged package. A special non-corrosive finish resists salt wa-

ter exposure and perspiration in extreme environments. The DSP-based design works with all Digital Hybrid recievers, and is backward compatible for use with Lectrosonics 200 and 100 Series and IFB receivers and some other brands of analog wireless receivers. Com-

panion receivers are covered in separate manuals. Super-Minature Belt Pack Transmitters Table of Contents General Technical Description ............................................. 4 Controls and Functions ........................................................ 6 LCD Screen ......................................................................... 6 Power LED ........................................................................... 6 Audio Input Jack ................................................................... 6 Battery Compartment and Thumb Screw ............................. 6 Modulation LEDs .................................................................. 6 Audio Button ........................................................................ 6 Freq Button .......................................................................... 6 Up/Down Arrows .................................................................. 6 Antenna ................................................................................ 6 Setup with the LCD ................................................................ 7 Audio Screen ....................................................................... 7 Frequency Screen ................................................................ 7 Compatibility Mode Screen .................................................. 7 Turning the Power On .......................................................... 7 Turning the Power Off .......................................................... 7 Entering the Standby Mode ................................................. 7 Lock/Unlock Screen ............................................................. 7 Battery Installation ................................................................ 8 Remote Control Operation ................................................... 8 Operating Instructions .......................................................... 9 Power Up and Boot Sequence ............................................. 9 Power Down ......................................................................... 9 Standby Mode ...................................................................... 9 Selecting the Compatibility Mode ......................................... 9 Setting Transmitter Operating Frequency ............................. 10 Adjusting the Low Frequency Roll-off .................................. 10 Attaching a Microphone and Adjusting Gain ........................ 10 Locking or Unlocking the Control Panel ............................... Attaching and Removing the Microphone ............................ Locking or Unlocking the Control Panel ............................... 11 Attaching and Removing the Microphone ............................ 11 5-Pin Input Jack Wiring ......................................................... 12 Installing the Connector: ...................................................... 12 Cable Termination for Non-Lectrosonics Microphones ..... 13 Microphone RF Bypassing ................................................... 14 Line Level Signals ................................................................ 14 Wiring Hookups for Different Sources ................................ 15 Works with Servo Bias Inputs Only: ..................................... 15 Works with Servo Bias Inputs and Earlier Transmitters: ....... 15 RM Remote Control Operating Instructions ....................... 16 RM Front Panel Controls ...................................................... 16 Powering the RM on and off ................................................. 16 Principles of Operation ......................................................... 16 RM Pages ............................................................................ 16 Operating Notes ................................................................... 17 RM Quick Reference ............................................................ 17 Troubleshooting ..................................................................... 18 RM Troubleshooting ............................................................. 19 Specifications and Features ................................................. 21 Service and Repair ................................................................ 22 Returning Units for Repair ................................................... 22 Rio Rancho, NM 3 SMa Series General Technical Description Wideband Design The SM transmitters use 75 kHz wide deviation for an excellent signal to noise ratio and wide dynamic range. The DSP controlled input limiter features a wide range dual envelope design which cleanly limits input signal peaks over 30 dB above full modulation. switching power supplies to provide constant voltages to the transmitter circuits from the beginning (1.5 Volts) to the end (0.85 Volts) of battery life, and an ultra low noise input amplifier for quiet operation. Servo Input The SM input is a radically different input system com-

pared to previous Lectrosonics transmitter microphone inputs. It is so superior that this input system will eventu-

ally be utilized by all Lectrosonics UHF transmitters. The improvements are audible and make the transmitters easier to use and much harder to overload. It is no longer necessary on some mics to introduce pads to prevent overload of the input stage, divide the bias voltage down for some low voltage mics, or reduce the limiter range at minimum gain settings. Digital Hybrid Wireless Technology*

All wireless links suffer from channel noise to some de-

gree, and all wireless microphone systems seek to mini-

mize the impact of that noise on the desired signal. Con-

ventional analog systems use compandors for enhanced dynamic range, at the cost of subtle artifacts (known as pumping and breathing). Wholly digital systems defeat the noise by sending the audio information in digital form, at the cost of some combination of power, bandwidth and resistance to interference.US Patent 7,225,135 Lectrosonics Digital Hybrid Wireless systems over-

come channel noise in a dramatically new way, digitally encoding the audio in the transmitter and decoding it in the receiver, yet still sending the encoded informa-

tion via an analog FM wireless link. This proprietary algorithm is not a digital implementation of an analog compandor but a technique that can be accomplished only in the digital domain, even though the inputs and outputs are analog. Channel noise still impacts received signal quality and will eventually overwhelm a receiver. Digital Hybrid Wireless simply encodes the signal to use a noisy channel as efficiently and robustly as possible, yield-

ing audio performance that rivals that of wholly digital systems, without the power and bandwidth problems inherent in digital transmission. Because it uses an analog FM link, Digital Hybrid Wire-

less enjoys all the benefits of conventional FM wire-

less systems, such as excellent range, efficient use of RF spectrum, and resistance to interference. However, unlike conventional FM systems, it does away with the analog compandor and its artifacts. No Pre-Emphasis/De-Emphasis The Digital Hybrid Wireless design results in a signal-to-

noise ratio high enough to preclude the need for conven-

tional pre-emphasis (HF boost) in the transmitter and de-

emphasis (HF roll off) in the receiver. This eliminates the potential for extreme distortion on signals with abundant high-frequency information. 4 LECTROSONICS, INC. Low Frequency Roll-Off Control Panel Super-Minature Belt Pack Transmitters The control panel includes four membrane switches and an LCD screen to adjust the operational settings. Multi-

color LEDs are used to indicate audio signal levels for accurate gain adjustment and for battery status. Wide-Band Deviation 75 kHz deviation improves the signal to noise ratio and audio dynamic range of a wireless system dramatically, compared to other designs that use 30 kHz to 40 kHz deviation. Wide deviation combined with a high powered transmitters makes a significant improvement in signal to noise ratio and operating range. Battery Options and Operating Time Switching power supplies convert regulated battery voltages to operate various circuit stages with maxi-

mum efficiency. With the variety of alkaline, lithium and rechargeable NiMH batteries available today in the AA format, there are many choices to maximize operating time or minimize cost as needed for any application. Frequency Blocks Lectrosonics established a block numbering system years ago to organize the range of frequencies avail-

able from the low 500 MHz band to the upper 700 MHz band. Each block includes 256 frequencies in 100 kHz increments. The block number is part of a simple formula to derive the frequency. The block number is multiplied by 25.6 to produce the lowest frequency in the block. For example, block 27 x 25.6 = 691.200. Circulator/Isolator The RF output circuit includes a one way circulator/isolator using a magnetically polarized ferrite. This device greatly reduces the RF intermodulation produced when multiple transmitters are used in close proximity to one another

(several feet apart). The isolator also provides additional RF output stage protection. The low frequency roll-off can be set for a 3 dB down point at 35, 50, 70, 100, 120 and 150 Hz to control sub-

sonic and very low frequency audio content in the au-

dio. The actual roll-off frequency will vary slightly depend-

ing upon the low frequency response of the microphone. Excessive low frequency content can drive the transmit-

ter into limiting, or in the case of high level sound sys-

tems, can even cause damage to loudspeaker systems. The roll-off is normally adjusted by ear while listening as the system is operating. Input Limiter A DSP-controlled analog audio limiter is employed before the analog-to-digital (A-D) converter. The limiter has a range of more than 30 dB for excellent overload protection. A dual release envelope makes the limiter acoustically transparent while maintaining low distortion. It can be thought of as two limiters in series, a fast attack and release limiter followed by a slow attack and release limiter. The limiter recovers quickly from brief transients, with no audible side effects, and also recovers slowly from sustained high levels, to keep audio distortion low and while preserving short term dynamics. Signal Encoding and Pilot Tone In addition to controlling the limiter, the DSP also en-

codes the digitized audio from the A-D converter and adds an ultrasonic pilot tone to control the receivers squelch. A pilot tone squelch system provides a reliable method of keeping a receiver output muted (squelched) even in the presence of significant interference. When the system is operating in the hybrid mode, a differ-

ent pilot tone frequency is generated for each carrier frequency to prevent inadvertent squelch problems and simplify multi-channel coordination. Microprocessor, PLL and VCO Circuits A microprocessor monitors user command inputs from the control panel buttons and numerous other internal signals. It works intimately with the DSP to ensure the audio is encoded according to the selected Compatibil-

ity Mode and that the correct pilot tone is added to the encoded signal. Compatibility Modes The SM transmitters were designed to operate with Lectrosonics Digital Hybrid receivers and will yield the best performance when doing so. However, due to the flexibility of digital signal processing, the transmitters can also operate in various compatibility modes for use with Lectrosonics 200 Series, Lectrosonics 100 Series, IFB and certain non-Lectrosonics receivers. Contact the Lectrosonics sales department for a complete list of compatible non-Lectrosonics receivers. Rio Rancho, NM 5 SMa Series Controls and Functions Modulation LEDs Battery Compartment Cover Plate LCD Battery Compartment Thumb Screw UP Arrow Audio Input Jack DOWN Arrow PWR LED AUDIO Button FREQ Button LCD Screen The LCD is a numeric-type Liquid Crystal Display with several screens that allow settings to be made with the AUDIO, FREQ, UP and DOWN to configure the trans-

mitter. Turn on and turn off countdowns appear in the LCD allowing the transmitter to be turned on for adjust-

ments without the output stage enabled, and to prevent accidental turn off. Power LED The PWR LED glows green when the battery is good. The color changes to red when there is about 30 minutes of operation left with the recommended lithium battery. An alkaline battery will have about 20 minutes of life left. When the LED begins to blink red, there are only a few minutes of life. Note: A NiMH battery will give little or no warning when it is depleted. If you wish to use NiMH batteries in the SM, we recommend trying fully charged batteries in the unit, noting the length of time that the batteries will run the unit and then using the battery timer feature available on most Digital Hybrid receivers. A weak battery will sometimes cause the PWR LED to glow green immediately after being put in the unit, but will soon discharge to the point where the LED will go red or shut off completely. When the SM is in SLEEP mode, the LED blinks green every few seconds (See Sleep Mode, page 8). Audio Input Jack The Servo Bias input on the SM Series transmitters accommodates virtually every lavaliere, handheld or shotgun microphone available, plus line level signals. Battery Compartment and Thumb Screw The large knurled thumbscrew is used to release or secure the Battery Compartment Cover Plate, allowing access to the battery. Modulation LEDs The Modulation LEDs provide a visual indication of the input audio signal level from the microphone. These two bicolor LEDs can glow either red or green to indicate modulation levels. 0 dB in the table below indicates full modulation. Signal Level Less than -20 dB

-20 dB to -10 dB

-10 dB to +0 dB

+0 dB to +10 dB Greater than +10 db Off Green Green Red Red Off Off Green Green Red

-20 LED

-10 LED Audio Button The AUDIO button is used to display the audio level setting and low frequency roll-off. The UP and DOWN arrows adjust the values. The AUDIO button is also used with the FREQ button to enter standby mode and to power the transmitter on or off. Freq Button The FREQ Button displays the selected operating frequency and also toggles the LCD between displaying the actual operating frequency in MHz and a two-digit hexadecimal number that corresponds to the equivalent Lectrosonics Frequency Switch Setting. The FREQ button is also used with the AUDIO button to enter standby mode and to power the transmitter on or off. Up/Down Arrows The Up and Down arrow buttons are used to select the operating frequency, adjust the audio level, or set the Compatibility Mode. Pressing both arrows simultaneously enters the lock countdown. Holding the two arrow buttons until the countdown completes locks the control panel buttons so they can only be used to display current settings. Loc is displayed to indicate the controls are locked. Once locked, the buttons can be unlocked only by re-

moving the battery, or via the RM remote control (if this function was enabled in the transmitter setup). Antenna The flexible antenna is built with woven, galvanized steel mesh cable, cut to the 1/4 wavelength of the center of the frequency block of the transmitter. The antenna is extremely rugged and moisture resistant. 6 LECTROSONICS, INC. Setup with the LCD Six screens are used to set up and operate the SM. These screens are used to set the operating frequency, adjust the audio input level, select the Compatibility Mode or lock the control panel and power down the transmitter. Audio Screen The Audio screen is used to adjust input gain from 0 to +44 dB, and the low frequency roll-

off from 35 to 150 Hz. Repeat-

edly pressing the AUDIO button toggles back and forth between the two displays. Press and hold the AUDIO button and use the Up and Down arrows to make adjustments. Frequency Screen The Frequency Screen dis-

plays the operating frequency in MHz or as a two-digit hexadecimal number that cor-

responds to the equivalent Lectrosonics Frequency Switch Setting. Pressing the FREQ button toggles between the two displays. Compatibility Mode Screen Holding down the Up arrow button while powering up the SM opens the Compatibility Mode screen. By using the Up or Down arrow buttons, the user can select one of six compatibility modes:

Note: RF transmission is prevented while selecting Compatibility Modes. Also, the SM exits the Compatibility Mode screen to Standby Mode. 400 - This is the factory default setting and works with all Lectrosonics 400 Series Digital Hybrid Wireless receivers, including the Venue. This mode offers the best audio quality. 200 - This mode works with all Lectrosonics 200 Series compatible receivers. 100 - This mode works with all Lectrosonics 100 Series compatible receivers. 3 - (Mode 3) This mode works with a number of non-Lectrosonics analog receivers. Contact the company for a list of compatible receivers. IFB - This mode works with all Lectrosonics IFB compatible receivers. 6 - (Mode 6) This mode works with a number of non-Lectrosonics analog receivers. Contact the company for a list of compatible receivers. While in the compatibility mode screen, pressing either the AUDIO or FREQ button exits to standby mode. To power off from the compatibility mode screen, press and hold AUDIO and FREQ together. Super-Minature Belt Pack Transmitters Turning the Power On With the power turned off, simultaneously pressing and holding the AUDIO and FREQ buttons displays a timer with numerals on the right. The numerals count up from one and the boot sequence begins when the count reaches three. LECtro is displayed as the boot sequence be-

gins. If either button is release prior to the screen reach-

ing numeral three, the unit will enter the Standby Mode with no RF output (see Standby Mode below). Initial Power On Timer Screen Turning the Power Off Initial Power Off With the unit turned on, simul-

taneously holding the AUDIO and FREQ buttons starts a countdown timer with numerals on the right. The screen counts down from three and the transmitter turns off when it reaches zero. Releas-

ing either button prior to the Power Off Timer screen indicating zero returns the unit to normal operation and displays the previous screen. imer Screen Entering the Standby Mode Standby Screen With the power turned off, pressing the AUDIO and FREQ buttons for about one second places the unit in Standby Mode. In this mode the RF output is turned off so all setup adjustments can be made without interfering with other systems operating in the same location. The screen displays rf OFF to remind the user that the unit is not transmitting. Holding the FREQ button in Standby Mode displays the current operating frequency of the transmitter. The op-

erating frequency can be changed by holding the FREQ button and pressing either the Up or Down button. Release the FREQ button, then press and hold it again to toggle the display between frequency in MHz and the hex code corresponding to the equivalent Lectrosonics Frequency Switch Setting. Holding the AUDIO button in Standby Mode displays the current audio input level setting. This level can be changed by holding the AUDIO button and pressing either the Up or Down button. Quickly pressing both the FREQ and AUDIO buttons simultaneiously when the unit is in Standby Mode pow-

ers off the transmitter. Lock/Unlock Screen Simultaneously pressing and holding both the Up and Down arrow buttons during normal operation starts the Lock timer. The timer starts at three and counts down to zero. When the timer reaches zero, the transmitters controls are locked. Rio Rancho, NM 7 SMa Series The LCD will display the locked condition as long as the arrow buttons are held, then revert back to the previous screen when either button is released. With the controls locked, the AUDIO and FREQ buttons can still be used to display current settings. Any attempt to change a setting by pressing either the Up or Down arrow button will result in an on-screen Loc reminder that the controls are locked. Remove the batteries to unlock the control panel. Important: Once the transmitter is locked, it cannot be unlocked or powered off using the buttons. The only ways to unlock a locked transmitter are to remove the battery or unlock it via the RM remote control. Remote Control Operation Remote Control Screens SM Series transmitters may be configured to respond to signals from the RM remote control unit or to ignore them. This setting is accessed by holding down the Down arrow button while powering the transmitter on. Use the arrow keys to toggle between rc on (remote control on) and rc oFF (remote control off). The default setting is rc on. If a remote control signal is detected but the transmitter is set to rc oFF, the message rc oFF will be dis-

played briefly on the transmitters LCD, to confirm that a valid signal was received, but that the transmitter is not configured to respond to it. Functions available from the remote control are:

Audio Level Frequency Lock/Unlock Buttons Sleep/Wake (power saving mode) In sleep mode, the SM uses 20% of the normal amount of current. For example, in sleep mode it will drain the battery as much in five hours as it would do in one hour of normal operation. Sleep mode can only be invoked with the remote control, and can only be revoked with the remote control or by removing the battery. When in sleep mode, the PWR LED blinks green every few seconds to indicate that the SM is asleep and not turned off. Note: The RM is not included with SM Series transmitters. Dweedle tones can also be downloaded from the web site at: www.lectrosonics.com. Go to the SM Series transmitter page and follow the link. Battery Installation The SM transmitter is powered by a single standard AA 1.5 volt battery, while the SMD and SMQ use two AA batteries. We recommend using lithium batteries for longest life. In the SM, lithium batteries provide over 4.5 hours of operation at room temperature. Note: Standard zinc-carbon batteries marked heavy-duty or long-lasting are not adequate. The battery status circuitry is designed for the voltage drop over the life of lithium batteries. To install new batteries:

1. Turn the Battery Cover Plate Thumbscrew coun-

terclockwise, open the battery compartment and remove any old batteries. 2. Insert the new battery (or batteries) into the hous-

ing. The positive (+) battery terminal goes into the transmitter first. 3. Replace the Battery Cover Plate and tighten the Battery Cover Plate Thumbscrew. Kevlar covered vent Battery Compartment Battery Cover Plate Thumbscrew Kevlar covered vent 8 LECTROSONICS, INC. Two Battery Compartments

(SMDa, SMQa) Operating Instructions Power Up and Boot Sequence 1) Ensure that good batteries are installed in the unit.

(See Battery Installation.) 2) Simultaneously press and hold the AUDIO and FREQ buttons until the Power On Boot Sequence is initiated. (See Power On Timer.) As the unit turns on, the Modulation LEDs and PWR LED all glow red, then green, and then they revert to normal opera-

tion, i.e., the Modulation LEDs glow according to the audio level present at the Audio Input Jack and the PWR LED glows green (with good batteries). Modulation LEDs UP Arrow DOWN Arrow PWR LED AUDIO Button FREQ Button The LCD displays a bootup sequence which con-

sists of four screens:

Company Name:

Frequency Block (bXX) and Firmware Version (rX.X):

Compatibility Mode:

Audio:

b21r1.1 (typ) CP 400 (typ) Aud 12 (typ) Lectro Power Down 1) Simultaneously press and hold the AUDIO and FREQ buttons while ob-

serving that the word Off appears in the LCD along with a counter. Initial Power Off Timer Screen 2) When the counter reaches 0, the unit turns off. Note: If the AUDIO and FREQ buttons are released before the LCD goes blank at the end of the countdown, the unit will not turn off. Instead, it will stay energized and the display will return to the previous screen. Super-Minature Belt Pack Transmitters Standby Mode Standby Mode allows the user to verify or change the transmitters operating frequency or audio input level without transmitting any signals. Standby Mode can only be invoked from a power off condition. Quickly press and release both the AUDIO and FREQ buttons simultaneously to enter and exit this mode. Selecting the Compatibility Mode 400 Series or Digital Hybrid Wireless Compatibility Mode All Digital Hybrid Wireless receivers are capable of work-

ing with the Lectrosonics SM transmitter. By selecting the proper compatibility mode, the SM will also work with 200 Series, 100 Series and IFB analog receivers, plus some other analog wire-

less receivers (contact the factory for details). Setting the Compatibility Mode of the transmitter to match the receiver is easily done via the Control Panel. Note: RF transmission is prevented while selecting Compatibility Modes. Also, the SM exits the Compatibility Mode screen to Standby Mode. (See Standby Mode, this section.) Note: The unit comes from the factory configured as a 400 Series transmitter. 1) Set the receivers audio controls to minimum. 2) Power up the SM and observe the Boot Sequence. If the Compatibility Mode for the SM does not match the corresponding receiver, then power off the SM transmitter. 3) From a power off condition, hold down the Up arrow, then simultaneously press the AUDIO and FREQ buttons. 4) The LCD will display the current Compatibility Mode. Use the Up or Down arrow buttons to set the Compatibility Mode to match the corresponding receiver. The following Compatibility Modes are available:

CP 100 100 Series mode:

200 Series mode:

CP 200 Mode 3 (Contact dealer for details): CP 3 400 Series mode:

IFB Series mode:

Mode 6 (Contact dealer for details): CP 6 CP 400 CP IFB 5) The Compatibility Mode selected in Step 4 will be the current Compatibility Mode until reset using this procedure. Pressing the AUDIO or FREQ exits into Standby Mode. To power off from the compatibility mode screen, press AUDIO and FREQ together. Rio Rancho, NM 9 SMa Series Setting Transmitter Operating Frequency Frequency displayed in MHz The Operating Frequency of the SM can be displayed either in MHz or as a two-digit hexadeci-

mal number. (See Controls and Functions, FREQ Button.) The SMs operating frequency can be set with the unit in Standby Mode or powered up for normal operation. Use the following procedure to change the Operating Frequency of the SM transmitter:

1) If the LCD is displaying something other than the Frequency Screen, press the FREQ button on the SM Control Panel to enter this screen. Frequency displayed as two-digit hexadecimal number Note: The default display is in MHz. Pressing the FREQ button again displays the operating frequency as a two-digit hexadecimal number that corresponds the equivalent Lectrosonics Frequency Switch Setting. 2) While holding the FREQ button, use the Up or Down arrow buttons to move the operating fre-

quency up or down in 100 kHz increments from the current setting. Note: The operating frequency displayed on the LCD wraps as it reaches the upper or lower end of its range. Thus, if you intend to move the operating frequency from the lower end of the range to the upper end, it may be faster to do this by using the Down arrow until the frequency wraps to the upper end. Most Lectrosonics receivers indicate the operating frequency both in MHz and as a two digit hexa-

decimal number. This conforms to the Lectrosonics tradition of setting the operating frequency using two 16-position rotary switches. The SM Series units offer the ability to set the operating frequency in a similar manner. Pressing the FREQ button while the LCD displays the operating frequency in MHz will change the display to show the equivalent two-digit hexadecimal frequency select switch set-

ting. Simply use the UP or DOWN arrow to increase or decrease the operating frequency. Adjusting the Low Frequency Roll-off Repeatedly press the AUDIO button until the LF roll-

off adjustment screen appears. Then press and hold the AUDIO button while selecting the desired roll-off frequency with the UP and DOWN arrows. Attaching a Microphone and Adjusting Gain The control panel Modulation LEDs indicate the modu-

lation level and limiter activity. Once set, the transmit-

ters audio level setting should not be used to control the volume of your sound system or recorder levels. This gain adjustment matches the transmitter gain with the microphones output level, the users voice level and the position of the microphone. The audio input level can be set with the unit in Standby Mode or while pow-

ered up in normal operation. Signal Level Less than -20 dB

-20 dB to -10 dB

-10 dB to +0 dB

+0 dB to +10 dB Greater than +10 db Off Green Green Red Red Off Off Green Green Red

-20 LED

-10 LED Note: Different voices will usually require different settings of the AUDIO control, so check this adjustment as each new person uses the system. If several different people will be using the transmitter and there is not time to make the adjustment for each individual, adjust it for the loudest voice. 1) With the SM powered off, insert the microphone plug into the Audio Input Jack, aligning the pins and ensuring that the connector locks. See the following page for suggestions on using the microphone connector and sleeve 2) Place the transmitter in Standby Mode, or if the unit is to be powered up and adjusted, mute the main sound system prior to powering up the transmitter. 3) Position the microphone in the location where it will be used in actual operation. 4) Observe the audio level LEDs while speaking or singing into the microphone at the same voice level that will be used during the program. While holding the AUDIO button, press the UP or DOWN arrow buttons until the both the -20 and -10 LEDs glow green, with the -20 LED occasionally flickering red. This will maximize the signal to noise ratio of the system with full modulation and provide subtle limit-

ing to prevent overload and audible compression of signal peaks. Note: Setting the audio level too high reduces the dynamic range of the audio signal. Setting the audio level too low may cause hiss and noise in the audio. 5) If the unit was set up in Standby Mode, it will be necessary to turn the transmitter off, then power it up again in normal operation so the RF output will be on. Then the other components in the sound or recording system can be adjusted. The roll-off frequency can be set to 35, 50, 70, 100, 120 and 150 Hz. 10 LECTROSONICS, INC. Locking or Unlocking the Control Panel The Lock mode protects the transmitter from accidental changes to its settings. 1) Ensure the SM setup is complete (operating fre-

Control Panel Locked quency, audio level, Compatibility Mode, sensitivity to remote control). 2) Simultaneously press both the Up and Down ar-

row buttons to start the Lock timer. When the timer reaches zero, Loc is displayed and the controls are locked. Important: Once the transmitter is locked, it cannot be unlocked or powered off using the buttons. The only ways to unlock a locked transmitter are to remove the battery or unlock it via the remote control. The remote control will work only if the transmitter was previously configured to respond to the remote control. The unit will always power up in unlocked mode. Attaching and Removing the Microphone The flexible sleeve over the 5-pin plug on the micro-

phone helps prevent dust and moisture from getting into the input jack. A flange is machined into the rim of the connector on the transmitter to help retain the sleeve after it is installed. The following procedure simplifies the attachment and removal of the microphone to assure the sleeve is seated securely. 1 Super-Minature Belt Pack Transmitters 2 Align the pins on the plug and jack and insert the connector. 3 Pinch and squeeze the sleeve on this end to work it down over the flange. Squeeze the end of the sleeve so you can feel the connector inside and press it into the jack until it latches. Pinch and squeeze the sleeve near the flange and work it down with a kneading motion over the flange all the way around until it stays in place flush with the housing. Pull on the connector to make sure it is firmly latched. 4 Pull the sleeve over the connector so the ends of the connector and sleeve are almost flush. Release button Rio Rancho, NM 11 To remove the connector, pull the sleeve back to expose the black release button. Press the button to unlatch the plug. SMa Series 5-Pin Input Jack Wiring The wiring diagrams included in this section represent the basic wiring necessary for the most common types of microphones and other audio inputs. Some micro-

phones may require extra jumpers or a slight variation on the diagrams shown. It is virtually impossible to keep completely up to date on changes that other manufacturers make to their products, thus you may encounter a microphone that differs from these instructions. If this occurs please call our toll-free number listed under Service and Repair in this manual or visit our web site at:

www.lectrosonics.com 1 2 3 4 5 GND BIAS MIC BIAS SELECT LINE IN

+5 VDC m h O 0 0 5 100 Ohm k 1

30uF Servo Bias Pin 4 to Pin 1 = 0 V Pin 4 Open = 2 V Pin 4 to Pin 2 = 4 V 200 Ohm 30uF

100 Ohm To Virtual Ground Audio Amplifier To Limiter Control

3.3uF 10k K 7

. 2 SM Equivalent Input Circuit Wiring Audio input jack wiring:

PIN 1 Shield (ground) for positive biased electret lava-

liere microphones. Shield (ground) for dynamic microphones and line level inputs. PIN 2 Bias voltage source for positive biased electret lavaliere microphones. PIN 3 Low impedance microphone level input for dynamic microphones. Also accepts hand-held electret microphones provided the microphone has its own built-in battery. PIN 4 Bias voltage selector for Pin 3. Pin 3 voltage (0, 2 or 4 volts) depends on Pin 4 connection. Pin 4 tied to Pin 1: 0 V 2 V Pin 4 Open:

Pin 4 to Pin 2:

4 V PIN 5 High impedance, line level input for tape decks, mixer outputs, musical instruments, etc. Insulator Insert Strain Relief TA5F Latchlock TA5F Backshell with Strain Relief Remove strain relief if using dust boot TA5F Backshell

(Strain Relief removed) Dust Boot (35510) Note: If you use the dust boot, remove the rubber strain relief that is attached to the TA5F cap, or the boot will not fit over the assembly. Installing the Connector:

1) If necessary, remove old connector from microphone cable. 2) Slide Rubber Boot onto microphone cable with the large end facing away from the microphone. (See illus-

tration above.) 3) If necessary, slide the 1/8-inch black shrink tubing onto the mircrophone cable. (This tubing is needed for some cables to ensure the cable fits snugly in the rubber boot.) 4) Use the resistors and connector included with this kit to configure the TA5F to your particular microphone.

(See Wiring Diagrams below.) A length of .065 OD clear tubing is included if insulating the resistor leads or shield wire is necessary. (Remove rubber strain relief from connector backshell by pulling it out of the backshell.) 5) Slide the Strain Relief over the TA5F Insert and crimp as shown to the right. Then insert the TA5F Insert and Strain Relief in the TA5F Latchlock. Screw the TA5F Flex Relief onto the TA5F Latchlock. 6) If needed, position and shrink the 1/8-inch shrink tub-

ing on the microphone cable, then slide the Rubber Boot down over the TA5F connector. 12 LECTROSONICS, INC. Super-Minature Belt Pack Transmitters Microphone Cable Termination for Non-Lectrosonics Microphones TA5F Connector Assembly Mic Cord Stripping Instructions 1 5 4 2 3 VIEW FROM SOLDER SIDE OF PINS 0.15"

0.3"

Crimping to Shield and Insulation Strip and position the cable so that the clamp can be crimped to contact both the mic cable shield and the insulation. The shield contact reduces noise with some microphones and the insulation clamp increases ruggedness. Shield Insulation Crimp these fingers to contact the shield Crimp these fingers to clamp the insulation NOTE: This termination is intended for UHF transmitters only. VHF transmitters with 5-pin jacks require a different termination. Lectrosonics lavaliere microphones are terminated for compatibility with VHF and UHF transmitters, which is different than what is shown here. Rio Rancho, NM 13 Line Level Signals The normal hookup for line level signals is: Signal Hot to pin 5, Signal Gnd to pin 1 and pin 4 jumped to pin 1. This allows signal levels up to 3V RMS to be applied without limiting. If more headroom is needed, insert a 20 k resistor in series with pin 5. Put this resistor inside the TA5F con-

nector to minimize noise pickup. SMa Series Microphone RF Bypassing When used on a wireless transmitter, the microphone element is in the proximity of the RF coming from the transmitter. The nature of electret microphones makes them sensitive to RF, which can cause problems with the microphone/transmitter compatibility. If the electret microphone is not designed properly for use with wire-

less transmitters, it may be necessary to install a chip capacitor in the mic capsule or connector to block the RF from entering the electret capsule. Some mics require RF protection to keep the radio signal from affecting the capsule, even though the transmitter input circuitry is already RF bypassed (see schematic diagram). If the mic is wired as directed, and you are having dif-

ficulty with squealing, high noise, or poor frequency response, RF is likely to be the cause. The best RF protection is accomplished by installing RF bypass capacitors at the mic capsule. If this is not pos-

sible, or if you are still having problems, capacitors can be installed on the mic pins inside the TA5F connector housing. 2 WIRE MIC 3 WIRE MIC Preferred locations for bypass capacitors SHIELD AUDIO CAPSULE TA5F CONNECTOR CAPSULE SHIELD AUDIO BIAS Alternate locations for bypass capacitors TA5F CONNECTOR Install the capacitors as follows: Use 330 pF capaci-

tors. Capacitors are available from Lectrosonics. Please specify the part number for the desired lead style. Leaded capacitors: P/N 15117 Leadless capacitors: P/N SCC330P All Lectrosonics lavaliere mics are already bypassed and do not need any additional capacitors installed for proper operation. 14 LECTROSONICS, INC. Super-Minature Belt Pack Transmitters Wiring Hookups for Different Sources In addition to the microphone and line level wiring hook-

ups illustrated below, Lectrosonics makes a number of cables and adapters for other situations such as con-

necting musical instruments (guitars, bass guitars, etc.) to the transmitter. Visit www.lectrosonics.com and click on Accessories, or download the master catalog. A lot of information regarding microphone wiring is also available in the FAQ section of the web site at:

http://www.lectrosonics.com/faq.htm Follow the instructions to search by model number or other search options. Compatible Wiring for Both Servo Bias Inputs and Earlier Transmitters:

2 VOLT POSITIVE BIAS 2-WIRE ELECTRET 4 VOLT POSITIVE BIAS 2-WIRE ELECTRET SHIELD A UDI O 3.3 k Compatible wiring for microphones such as Countryman E6 headworn and B6 lavaliere. 1.5 k PIN 1 2 3 4 5 4 3 5 1 2 T A5 F PLUG Most common type of wiring for lavaliere mics. Fully compatible with 5-pin inputs on Lectrosonics transmitters such as the LM and UM Series. 2 VOLT POSITIVE BIAS 2-WIRE ELECTRET - DPA MICROPHONES UNBALANCED LINE LEVEL SIGNALS This wiring is for DPA lavalier and headset microphones. NOTE: The resistor value can range from 3k to 4k ohms. 2 VOLT NEGATIVE BIAS 2-WIRE ELECTRET 2.7 k SHIELD AUDIO Compatible wiring for microphones such as negative bias TRAM models. NOTE: The resistor value can range from 2k to 4k ohms. PIN 1 2 3 4 5 4 3 5 1 2 T A5 F PLUG 4 VOLT POSITIVE BIAS 3-WIRE ELECTRET WITH EXTERNAL RESISTOR Used for 3-wire lavaliere microphones that require an external resistor such as the Sanken COS-11. SHIELD DRAIN (BIAS) SOURCE (AUDIO) This wiring is fully compatible with 5-pin inputs on Lectrosonics transmitters such as the LM and UM Series. This is the wiring for the Lectrosonics M152 lavaliere microphone. SLEEVE SHIELD A UDI O LINE LEVEL RCA or 1/4 PLUG TIP For signal levels up to 3V (+12 dBu) before limiting. Fully compatible with 5-pin inputs on other Lectrosonics transmitters such as the LM and UM Series. A 20k ohm resistor can be inserted in series with Pin 5 for an additional 20 dB of attenuation to handle up to 30V (+32 dBu). PIN 1 2 3 4 5 4 3 5 1 2 T A5 F PLUG BALANCED AND FLOATING LINE LEVEL SIGNALS XLR JACK

*NOTE: If the output is balanced but center tapped to ground, such as on all Lectrosonics receivers, do not connect Pin 3 of the XLR jack to Pin 4 of the TA5F connector. TA5F PLUG LO-Z MICROPHONE LEVEL SIGNALS XLR JACK For low impedance dynamic mics or electret mics with internal battery or power supply. Simple Wiring for Servo Bias Inputs Only:

2 VOLT POSITIVE BIAS 2-WIRE ELECTRET 4 VOLT POSITIVE BIAS 3-WIRE ELECTRET Simplified wiring for microphones such as Countryman B6 Lavalier and E6 Earset models and others. NOTE: This servo bias wiring is not compatible with earlier versions of Lectrosonics transmitters. Check with the factory to confirm which models can use this wiring. 2 VOLT NEGATIVE BIAS 2-WIRE ELECTRET Simplified wiring for microphones such as negative bias TRAM. NOTE: This servo bias wiring is not compatible with earlier versions of Lectrosonics transmitters. Check with the factory to confirm which models can use this wiring. NOTE: This servo bias wiring is not compatible with earlier versions of Lectrosonics transmitters. Check with the factory to confirm which models can use this wiring. Rio Rancho, NM 15 SMa Series RM Remote Control Operating Instructions RM Front Panel Controls The RM unit gives you remote control of SM Series transmitters using an audible tone delivered to the transmitters microphone. Operating parameters on the transmitter can be set by holding the speaker on the RM close to the microphone and pressing the pushbut-

ton. A dweedle tone will play from the RM speaker into the microphone and the parameter on the transmitter will be set immediately. Available adjustments:

Audio input gain Frequency Lock or Unlock Modes Sleep Mode ON/OFF When an SM Series Transmitter is in the power sav-

ing sleep mode, it uses only 20% of the normal bat-

tery drain, so battery life with be 5 times longer. This is especially useful in situations where the transmitter is buried deep inside costuming and there are wait-

ing periods between use. The transmitter can sleep for several hours and then be awakened and adjusted when the production is about to begin. Powering the RM on and off To turn the RM on or off, press the AUDIO and FREQ buttons together briefly. The unit powers up on the page that was displayed when the unit was powered off last. Principles of Operation The RM user interface is organized into pages which are accessible via the AUDIO and FREQ buttons. Once on a page, settings can be adjusted with the UP and DOWN arrow buttons. To change a transmitters setting via the RM, it is neces-

sary to dial in the new setting on the appropriate page on the RM, and then press the SEND button (on the side, near the speaker). The speaker should be uncov-

ered and held within a few inches of the transmitters microphone. (The longest usable range is about 6 feet, depending on the microphone and volume settings used.) A single AA Lithium battery will operate the RM for up to several years. NOTE: Only the specific function displayed is altered. For example, if the remote control is on the CH (channel) screen, pressing the send button will set the transmitters channel but will not affect any other setting on the transmitter at that time. RM Pages The AUDIO button cycles through 4 pages:

1) Aud - set transmitters audio level 2) SLEEP/unSLP - cause transmitter to sleep or wake up 3) Loc/unLoc - lock or unlock transmitters buttons 4) Loud - adjust RM speaker volume

(press SEND button for a sample tone) The FREQ button cycles through 2 or 3 pages, depend-

ing on the settings:

1) CH - set transmitters channel

(using block-independent hex code) 2) b - select a block number

(optional uncovers next page) 3) 000.000 - set transmitters frequency in MHz

(avail. if a block is selected) Speaker SEND Button When the SEND button is pressed, the selected RM setting is transmitted via the RM speaker to the microphone attached to the SM Transmitter. 16 LECTROSONICS, INC. Super-Minature Belt Pack Transmitters The RM should be held close enough to the microphone to change the settings on the intended transmitter, but not be so loud as to affect other transmitters nearby. RM Quick Reference Power On/Off Set SM audio level Sleep or Wake SM Lock or Unlock SM Adjust RM volume Set SM channel (hex) Enable MHz display Set SM channel (MHz) AUDIO+FREQ Aud page (via AUDIO) SLEEP/unSLP page (via AUDIO) Loc/unLoc page (via AUDIO) Loud page (via AUDIO) CH page (via FREQ) b (block) page (via FREQ) 000.000 page (via FREQ) Operating Notes The sensitivity to the remote control varies with the trans-

mitters audio level setting and the microphone used, but it is always possible to make it work with a sufficiently loud remote signal at close range. If the SM is configured to re-

spond to the remote control, it will do so even if the but-

tons are locked. When the SM is asleep, it can only be awakened by the re-

mote control, or by removing and reinserting the battery. When the SM is asleep, the PWR led blinks green every few seconds. If a remote command is sent that would result in the same display being shown again on the SM (for example tuning to the chan-

nel already displayed), a row of dashes is displayed briefly, as a signal that the command was received, but it didnt change anything. If you are having trouble getting the SM to respond, make sure you arent covering the RMs speaker with your thumb, and/or turn up the RMs speaker volume on the Loud page. If the RM is set to a different block number than the transmitter and an attempt is made to set the transmitters frequency in MHz, the command will still work. The transmitter is simply set to the corresponding channel in the correct block, with a matching hex code. Since all SM transmitters respond to the same sig-

nals, take care that the remote control is presented only to the desired transmitter, with the minimum speaker volume necessary to do the job reliably. Note: The audio signal from the RM will change the settings of all transmitters within range. Experiment with this to prevent accidental changes on another transmitter during production. Rio Rancho, NM 17 SMa Series Troubleshooting Before going through the following chart, be sure that you have a good battery in the transmitter. It is important that you follow these steps in the sequence listed. SYMPTOM POSSIBLE CAUSE TRANSMITTER PWR LED OFF TRANSMITTER PWR LED BLINKS GREEN EVERY FEW SECONDS, TRANSMITTER DOES NOT RESPOND OTHERWISE 1) Battery is inserted backwards or dead. 2) Transmitter not powered up. (See Operating Instructions, 1) Transmitter has been put to sleep by the remote control. Either use the remote control to wake it up again or remove and reinsert the transmitters battery. Power UP and Boot Sequence.) AUDIO LEVEL LEDs NOT LIGHTING 1) Gain control set to minimum. 2) Battery is dead or installed backwards. Check PWR LED. 3) Mic capsule is damaged or malfunctioning. 4) Mic cable damaged or mis-wired. RECEIVER RF INDICATOR OFF 1) Transmitter not turned on, or is in Standby Mode. 2) Transmitter battery is dead. 3) Receiver antenna missing or improperly positioned. 4) Transmitter and receiver not on same frequency. 5) Transmitter and receiver not on same frequency block. 6) Operating range is too great. 7) Defective transmitter antenna - unit needs repair. Check switches/display on transmitter and receiver. NO SOUND (OR LOW SOUND LEVEL), RECEIVER INDICATES PROPER AUDIO MODULATION 1) Receiver output level set too low. 2) Receiver output disconnected, or cable defective or mis-wired. 3) Sound system or recorder input is turned down. DISTORTED SOUND EXCESSIVE FEEDBACK LEDs and receiver audio levels as SM is being used. recorder input. Adjust output level on receiver to the correct level for the recorder, mixer or sound system. (Use the receivers Tone function to check level.) 1) Transmitter gain (audio level) is far too high. Check SM 2) Receiver output may be mismatched with the sound system or 3) Excessive wind noise or breath pops. Reposition microphone 4) Transmitter is not set to same frequency as receiver. Check that operating frequency on receiver and transmitter match. 5) Receiver/Transmitter Compatibility Mode mismatched. and/or use a larger windscreen. and/or reduce receiver output level. 1) Transmitter gain (audio level) too high. Check gain adjustment 2) Talent standing too close to speaker system. 3) Mic is too far from users mouth. 18 LECTROSONICS, INC. Super-Minature Belt Pack Transmitters SYMPTOM POSSIBLE CAUSE HISS AND NOISE -- AUDIBLE DROPOUTS 1) Transmitter gain (audio level) far too low. 2) Receiver antenna missing or obstructed. 3) Transmitter antenna broken or missing. 4) Operating range too great. 5) Signal interference. Turn off transmitter. If receivers signal strength indicator does not drop to nearly zero, this indicates an interfering signal may be the problem. Try a different operating frequency. Loc APPEARS IN DISPLAY WHEN ANY BUTTON IS PRESSED 1) Control Panel is locked. (See Operating Instructions, Locking and Unlocking the Control Panel.) Hold APPEARS IN DISPLAY WHEN ARROW BUTTONS ARE PRESSED 1) Reminder that it is necessary to hold down the AUDIO or FREQ button to make adjustments to the audio gain or frequency settings. PLL APPEARS IN DISPLAY TRANSMITTER WONT RESPOND TO REMOTE CONTROL 1) Indication that the PLL is not locked. This is a serious condition that requires factory repair. It may be possible to operate on another frequency far removed from the one that was selected when the unlocked condition was indicated. requested by the remote control. to respond to the remote control. See Remote Control Operation on page 16 for instructions on how to configure. 1. If LCD blinks rc oFF, transmitter has not be configured 2. If LCD blinks - - - - - -, transmitter is already set as 3. If transmitter doesnt not respond at all, try moving the remote 4. SM, SMD and SMQ transmitters must have firmware ver. 1.5 or higher to work with the RM. All a versions of the SM Series will work from firmware ver. 1.0 and up. The firmware version will flash briefly on the right side of the LCD during power up. control closer to the microphone or increasing the remote controls loudness setting, or increasing audio level on transmitter. RM Troubleshooting SM FREQUENCY CHANGES, BUT NOT TO DESIRED FREQUENCY RM FAILS TO CHANGE SETTINGS ON TRANSMITTER 1) RM set on different block than transmitter in question. RM uses hex code to set frequency - set RM to proper frequency block, or use hex code method to change frequency. 1) Make sure volume of RM and proximity of microphone are 2) Make sure transmitter is not in Sleep mode. sufficient to engage transmitter. Rio Rancho, NM 19 SMa Series 20 LECTROSONICS, INC. Specifications and Features Block 470 470.100 - 495.600 486.400 - 511.900 Block 19 Block 20 512.000 - 537.500 Block 21 537.600 - 563.100 Block 22 563.200 - 588.700 Block 23 588.800 - 607.900 and 614.100 - 614.300 Block 24 614.400 - 639.900 Block 25 640.000 - 665.500 Block 26 665.600 - 691.100 Block 27 691.200 - 716.700 Block 28 716.800 - 742.300 Block 29 742.400 - 767.900 Block 944 944.100 - 951.900

(Frequency usage varies by country) Operating frequencies:

Frequency range:

Channel Spacing:

Frequency selection:

RF Power output:

Compatibility Modes (6) Pilot tone:

Frequency stability:

Deviation:

Spurious radiation:

Equivalent input noise:

Input level:

Input impedance:

Input limiter:

If set for dynamic mic:

If set for electret lavaliere mic:

Line level input:

Dynamic mic:

Electret lavaliere:

Line level:

256 frequencies in 100 kHz steps for one 25.5 MHz wide block 100 kHz Control panel mounted membrane switches SMa:

100 mW (nominal) SMDa: 100 mW (nominal) SMQa: 250 mW (nominal) Digital Hybrid Wireless (400 Series), 200 Series, 100 Series, Mode 3

(other analog), Mode 6, and IFB 25 to 32 kHz; 5 kHz deviation

(in 400 Series Mode) 0.002%

75 kHz max. (in 400 Series Mode) 60 dB below carrier 125 dBV, A-weighted 0.5 mV to 50 mV before limiting. Greater than 1 V with limiting. 1.7 uA to 170 uA before limiting. Greater than 5000 uA (5 mA) with limiting. 5.0 mV to 6 V before limiting. Greater than 15 V with limiting. 300 Ohms Input is virtual ground with servo adjusted constant current bias 2.7 k Ohms Soft limiter, 30 dB range Super-Minature Belt Pack Transmitters Bias voltages:

Gain control range:

Modulation indicators:

Controls:

Low frequency roll-off:

Fixed 5 V at up to 5 mA Selectable 2 V or 4 V servo bias for any electret lavaliere. 40 dB; panel mounted membrane switches Dual bicolor LEDs indicate modulation of 20, -10, 0, +10 dB referenced to full modulation. Control panel with LCD and four membrane switches. Adjustable from 35 to 150 Hz.

+6

+3 0dB

-3

-6

-9

-12 Mic in 35 Hz Roll-off Line in Mic in 150 Hz Roll-off 30 100 1kHz 10k 20k Audio Frequency Response:

Signal to Noise Ratio (dB):

(overall system, 400 Series mode)

(Note: the dual envelope soft limiter provides exceptionally good handling of transients using variable attack and release time constants. The gradual onset of limiting in the design begins below full modulation, which reduces the measured figure for SNR without limiting by 4.5 dB) 35 Hz to 20 kHz, +/-1 dB (The low frequency roll-off is adjustable - see graph above) w/Limiting 108.0 111.5 113.0 No Limiting 103.5 107.0 108.5 SmartNR OFF NORMAL FULL Total Harmonic Distortion:

Audio Input Jack:

Antenna: Flexible, unbreakable steel cable. Batteries:

Battery Life:

Weight:

Overall Dimensions:

0.2% typical (400 Series mode) Switchcraft 5-pin locking (TA5F) 1.5 Volt AA lithium or rechargeable NiMH recommended SM: 1.5 hours (alkaline); 5.5 hours (lithium), 4 hours with 2500mAh NiMH SMD: 5.75 hours (alkaline); 14.25 hours (lithium), 8.5 hours with 2500mAh NiMH SMQ: 1.75 hours (alkaline); 7.5 hours (lithium), 5 hours with 2500mAh NiMH RM: 2.3 oz.. (65.8 grams) with lithium battery SM: 2.7 oz.. (75.9 grams) with lithium battery SMD/Q: 3.7 oz.. (105 grams) with lithium batteries SM/RM: 2.3 x 1.8 x 0.64 inches

(not including microphone/lanyard) 58 x 46 x 16 mm

(not including microphone/lanyard) SMD/Q: 2.3 x 2.4 x 0.64 inches

(not including microphone) 58 x 60 x 16 mm

(not including microphone) The FCC requires that the following statements be included in this manual for SM Series transmitters:

For body worn operation, this SM Belt-Pack Transmitter has been tested and meets the FCC RF exposure guidelines when used with the Lectrosonics accessories supplied or designated for this product. Use of other accessories may not ensure compliance with FCC RF exposure guidelines. Contact Lectrosonics if you have any questions or need more information about RF exposure using this product.. This device complies with FCC radiation exposure limits as set forth for an uncontrolled environment. This device should be installed and operated so that its antenna(s) are not co-

located or operating in conjunction with any other antenna or transmitter. Emission Designator: 180KF3E Specifications subject to change without notice. The FCC requires that the following statement be in-

cluded in this manual for the RM:

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Rio Rancho, NM 21 SMa Series Service and Repair If your system malfunctions, you should attempt to correct or isolate the trouble before concluding that the equipment needs repair. Make sure you have followed the setup procedure and operating instructions. Check the interconnecting cables and then go through the Troubleshooting section in this manual. We strongly recommend that you do not try to repair the equipment yourself and do not have the local repair shop at-

tempt anything other than the simplest repair. If the repair is more complicated than a broken wire or loose connection, send the unit to the factory for repair and service. Dont attempt to adjust any controls inside the units. Once set at the factory, the various controls and trimmers do not drift with age or vibration and never require readjustment. There are no adjustments inside that will make a malfunctioning unit start working. LECTROSONICS Service Department is equipped and staffed to quickly repair your equipment. In warranty repairs are made at no charge in accordance with the terms of the warranty. Out-of-warranty repairs are charged at a modest flat rate plus parts and shipping. Since it takes almost as much time and effort to determine what is wrong as it does to make the repair, there is a charge for an exact quotation. We will be happy to quote approximate charges by phone for out-of-warranty repairs. Returning Units for Repair For timely service, please follow the steps below:

A. DO NOT return equipment to the factory for repair without first contacting us by email or by phone. We need to know the nature of the problem, the model number and the serial number of the equipment. We also need a phone number where you can be reached 8 A.M. to 4 P.M. (U.S. Mountain Standard Time). B. After receiving your request, we will issue you a return authorization number (R.A.). This number will help speed your repair through our receiving and repair departments. The return authorization number must be clearly shown on the outside of the shipping container. C. Pack the equipment carefully and ship to us, shipping costs prepaid. If necessary, we can provide you with the proper packing materials. UPS is usually the best way to ship the units. Heavy units should be double-boxed for safe transport. D. We also strongly recommend that you insure the equipment, since we cannot be responsible for loss of or dam-

age to equipment that you ship. Of course, we insure the equipment when we ship it back to you. Lectrosonics USA:

Mailing address:

Lectrosonics, Inc. PO Box 15900 Rio Rancho, NM 87174 USA Web:

www.lectrosonics.com Shipping address:

Lectrosonics, Inc. 581 Laser Rd. Rio Rancho, NM 87124 USA E-mail:

sales@lectrosonics.com Telephone:

(505) 892-4501

(800) 821-1121 Toll-free

(505) 892-6243 Fax Lectrosonics Canada:

Mailing Address:

49 Spadina Avenue, Suite 303A Toronto, Ontario M5V 2J1 Telephone:

(416) 596-2202

(877) 753-2876 Toll-free

(877-7LECTRO)

(416) 596-6648 Fax E-mail:

Sales:

Service: joeb@lectrosonics.com colinb@lectrosonics.com 22 LECTROSONICS, INC. Super-Minature Belt Pack Transmitters Rio Rancho, NM 23 LIMITED ONE YEAR WARRANTY The equipment is warranted for one year from date of purchase against defects in materials or workmanship provided it was purchased from an authorized dealer. This warranty does not cover equipment which has been abused or damaged by careless handling or shipping. This warranty does not apply to used or demonstrator equipment. Should any defect develop, Lectrosonics, Inc. will, at our option, repair or replace any defective parts without charge for either parts or labor. If Lectrosonics, Inc. cannot correct the defect in your equipment, it will be replaced at no charge with a similar new item. Lectrosonics, Inc. will pay for the cost of returning your equipment to you. This warranty applies only to items returned to Lectrosonics, Inc. or an authorized dealer, shipping costs prepaid, within one year from the date of purchase. This Limited Warranty is governed by the laws of the State of New Mexico. It states the entire liablility of Lectrosonics Inc. and the entire remedy of the purchaser for any breach of warranty as outlined above. NEITHER LECTROSONICS, INC. NOR ANYONE INVOLVED IN THE PRODUCTION OR DELIVERY OF THE EQUIPMENT SHALL BE LIABLE FOR ANY INDIRECT, SPECIAL, PUNITIVE, CONSEQUENTIAL, OR INCIDENTAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THIS EQUIPMENT EVEN IF LECTROSONICS, INC. HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. IN NO EVENT SHALL THE LIABILITY OF LECTROSONICS, INC. EXCEED THE PURCHASE PRICE OF ANY DEFECTIVE EQUIPMENT. This warranty gives you specific legal rights. You may have additional legal rights which vary from state to state. 581 Laser Road NE Rio Rancho, NM 87124 USA www.lectrosonics.com

(505) 892-4501 (800) 821-1121 fax (505) 892-6243 sales@lectrosonics.com SMa_Seriesman.indd 3 Mar 2008