FCC ID: DBZSMWBB2 Wireless Microphone Transmitter

INSTRUCTION MANUAL SMWB Series Wireless Microphone Transmitters and Recorders Featuring Digital Hybrid Wireless Technology US Patent 7,225,135 Fill in for your records:

Serial Number:

Purchase Date:

Rio Rancho, NM, USA www.lectrosonics.com FCC Notices:

For body worn operation, this transmitter model has been tested and meets the FCC RF exposure guidelines when used with the Lectrosonics accessories supplied or designated for this product. Use of other accessories may not ensure compliance with FCC RF exposure guidelines. Contact Lectrosonics if you have any questions or need more information about RF exposure using this product.. This device complies with FCC radiation exposure limits as set forth for an uncontrolled environment. This device should be installed and operated so that its antenna(s) are not co-located or operating in conjunction with any other antenna or transmitter. 2 SMWB SeriesLECTROSONICS, INC. Table of Contents Introduction ............................................................................ 5 About Digital Hybrid Wireless ................................................................................5 Servo Bias Input and Wiring ................................................ 5 DSP-controlled Input Limiter ................................................ 5 Recorder function ................................................................. 5 Features .................................................................................. 6 Battery Status LED Indicator ............................................... 6 Battery Installation ................................................................ 7 Turning Power ON and OFF .................................................. 8 Selecting between Transmit and Record Modes................. 8 Transmitter Operating Instructions ..................................... 9 Record Mode Operating Instructions .................................. 9 Xmit (transmitter) Mode Main Menu ................................... 10 Xmit (transmitter) Mode Power Menu ................................ 11 Record Mode Main Menu .................................................... 12 Record Mode Power Menu .................................................. 13 Setup Screen Details on Xmit Menus ................................ 14 Locking/Unlocking Changes to Settings............................. 14 Main Window Indicators ..................................................... 14 Connecting the Signal Source ........................................... 14 Using Line Level and Instrument Inputs ............................ 14 Helpful Features on Receivers ........................................... 14 Adjusting the Input Gain ..................................................... 15 Selecting Frequency .......................................................... 15 Selecting Frequency Using Two Buttons ............................ 16 About Overlapping Frequency Bands ................................ 16 Selecting the Low Frequency Roll-off ................................ 16 Selecting the Compatibility (Compat) Mode ....................... 16 Selecting Step Size ............................................................ 16 Selecting Audio Polarity (Phase) ........................................ 17 Setting Transmitter Output Power ...................................... 17 Restoring Default Settings ................................................. 17 5-Pin Input Jack Wiring ....................................................... 18 Microphone Cable Termination for Non-Lectrosonics Microphones ............................ 19 Input Jack Wiring for Different Sources ............................ 20 Compatible Wiring for Both Servo Bias Inputs and Earlier Transmitters: .................................................... 20 Simple Wiring for Servo Bias Inputs ONLY: ........................ 20 Microphone RF Bypassing ................................................. 21 Line Level Signals .............................................................. 21 Firmware Update ................................................................. 22 Recovery Process ............................................................... 23 Troubleshooting ................................................................... 24 Specifications ...................................................................... 25 Service and Repair .............................................................. 26 Returning Units for Repair ................................................. 26 Consumer Alert for US Users - FCC Order DA 10-92 Most users do not need a license to operate this wireless microphone system. Nevertheless, operating this micro-

phone system without a license is subject to certain restrictions: the system may not cause harmful interference; it must operate at a low power level (not in excess of 50 milliwatts); and it has no protection from interference received from any other device. Purchasers should also be aware that the FCC is currently evaluating use of wireless mi-

crophone systems, and these rules are subject to change. For more information, call the FCC at 1-888- CALL-FCC

(TTY: 1-888-TELL-FCC) or visit the FCCs wireless microphone website at www.fcc.gov/cgb/wirelessmicrophones. To operate wireless microphone systems at power greater than 50mW, you must qualify as a Part 74 user and be licensed. If you qualify and wish to apply for a license go to: http://www.fcc.gov/Forms/Form601/601.html 3 Digital Hybrid Wireless Belt-Pack TransmittersRio Rancho, NM 4 SMWB SeriesLECTROSONICS, INC. Introduction The design of the SMWB transmitter delivers the ad-

vanced technology and features of Digital Hybrid Wire-

less in a Lectrosonics belt-pack transmitter at a modest cost. Digital Hybrid Wireless combines a 24-bit digital audio chain with an analog FM radio link to eliminate a compandor and its artifacts, yet preserve the extended operating range and noise rejection of the finest ana-

log wireless systems. DSP compatibility modes allow the transmitter to also be used with a variety of analog receivers by emulating the compandors found in earlier Lectrosonics analog wireless and IFB receivers, and certain receivers from other manufacturers (contact the factory for details). The housing is a rugged, machined aluminum package. The input jack is a standard Lectrosonics 5-pin type for use with electret lavaliere mics, dynamic mics, musi-

cal instrument pickups and line level signals. The LEDs on the keypad allow quick and accurate level settings without having to view the receiver. The unit is powered by two AA batteries. The antenna port uses a standard 50 ohm SMA connector. The switching power supplies in the provide constant voltages to the transmitter circuits from the beginning to the end of battery life, with output power remaining con-

stant over the life of the battery. The input amplifier uses an ultra low noise op amp. Input gain is adjustable over a 44 dB range, with a DSP-controlled dual envelope input limiter providing a clean 30 dB range to prevent overload from signal peaks. About Digital Hybrid Wireless All wireless links suffer from channel noise to some degree, and all wireless microphone systems seek to minimize the impact of that noise on the desired signal. Conventional analog systems use compandors for enhanced dynamic range, at the cost of subtle artifacts

(known as pumping and breathing). Wholly digital systems defeat the noise by sending the audio informa-

tion in digital form, at the cost of some combination of power, bandwidth, operating range and resistance to interference. The Lectrosonics Digital Hybrid Wireless system over-

comes channel noise in a dramatically new way, digitally encoding the audio in the transmitter and decoding it in the receiver, yet still sending the encoded informa-

tion via an analog FM wireless link. This proprietary algorithm is not a digital implementation of an analog compandor but a technique which can be accomplished only in the digital domain. Since the RF link between transmitter and receiver is FM, channel noise will increase gradually with in-

creased operating range and weak signal conditions, however, the Digital Hybrid Wireles system handles this situation elegantly with rarely audible audio artifacts as the receiver approaches its squelch threshold. In contrast, a purely digital system tends to drop the audio suddenly during brief dropouts and weak signal conditions. The Digital Hybrid Wireless system simply encodes the signal to use a noisy channel as efficiently and robustly as possible, yielding audio performance that rivals that of purely digital systems, without the power, noise and bandwidth problems inherent in digital transmission. Because it uses an analog FM link, Digital Hybrid Wireless enjoys all the benefits of conventional FM wireless systems, such as excellent range, efficient use of RF spectrum, and long battery life. Servo Bias Input and Wiring The input preamp is a unique design that delivers audible improvements over conventional transmitter inputs. Two different microphone wiring schemes are available to simplify and standardize the configuration. Simplified 2-wire and 3-wire configurations provide sev-

eral arrangements designed for use only with servo bias inputs to take full advantage of the preamp circuitry. A line level input wiring provides an extended frequency response with an LF roll-off at 35 Hz for use with instru-

ments and line level signal sources. DSP-controlled Input Limiter The transmitter employs a digitally-controlled analog audio limiter prior to the analog-to-digital converter. The limiter has a range greater than 30 dB for excellent overload protection. A dual release envelope makes the limiter acoustically transparent while maintaining low distortion. It can be thought of as two limiters in series, connected as a fast attack and release limiter followed by a slow attack and release limiter. The limiter recovers quickly from brief transients, so that its action is hidden from the listener, but recovers slowly from sustained high levels to keep audio distortion low and preserve short term dynamic changes in the audio. Recorder function The SMWB has a built in recording function for use in situations where RF may not be possible or to work as a stand alone recorder. The record function and trans-

mit functions are exclusive of each other - you cannot record AND transmit at the same time. The recorder samples at 44.1kHz rate with a 24 bit sample depth.

(the rate was selected due to the required 44.1kHz rate used for the digital hybrid algorithm). The micro SD card also offers easy firmware update capabilities without the need for a USB cable or driver issues. 5 Digital Hybrid Wireless Belt-Pack TransmittersRio Rancho, NM Features Modulation Indicators REC

-40

-20 0 Battery Status LED microSDHC memory card port Audio Input Jack Antenna Port microSDHC memory card port Audio Input Jack Antenna Port Battery Status LED Indicator AA batteries can be used to power the transmitter. The LED labeled BATT on the keypad glows green when the batteries are good. The color changes to red when the battery voltage drops down and stays red through most of the battery life. When the LED begins to blink red, there will be only a few minutes remaining. The exact point at which the LEDs turn red will vary with battery brand and condition, temperature and power consumption. The LEDs are intended to simply catch your attention, not to be an exact indicator of remaining time. A weak battery will sometimes cause the LED to glow green immediately after the transmitter is turned on, but it will soon discharge to the point where the LED will turn red or the unit will turn off completely. Some batteries give little or no warning when they are depleted. If you wish to use these batteries in the transmitter, you will need to manually keep track of the operating time to prevent interruptions caused by dead batteries. Start with a fully charged battery, then measure the time it takes for the Power LED to go out completely. NOTE: The battery timer feature in many Lectrosonics receivers is very helpful in measuring battery runtime. Refer to the receiver instructions for details on using the timer. 6 SMWB SeriesLECTROSONICS, INC. Battery Installation The transmitter is powered by two AA batteries. We recommend using lithium for longest life. Because some batteries run down quite abruptly, using the Power LED to verify battery status will not be reli-

able. However, it is possible to track battery status using the battery timer function available in Lectrosonics Digital Hybrid Wireless receivers. The battery door opens by simply unscrewing the knurled knob part way until the door will rotate. The door is also easily removed by unscrewing the knob completely, which is helpful when cleaning the battery contacts. The battery contacts can be cleaned with alcohol and a cotton swab, or a clean pencil eraser. Be sure not to leave any remnants of the cotton swab or eraser crumbs inside the compartment. A small pinpoint dab of silver conductive grease* on the thumbscrew threads can improve battery performance and operation. Do this if you experience a drop in bat-

tery life or an increase in operating temperature. Insert the batteries according to the markings on the back of the housing. If the batteries are inserted incor-

rectly, the door may close but the unit will not operate.

*if you are unable to locate a supplier of this type of grease - a local electronics shop for example - contact the factory for a small maintenance vial. 7 Digital Hybrid Wireless Belt-Pack TransmittersRio Rancho, NM Turning Power ON and OFF Turning the Power ON The power button turns the unit on and off, and pro-

vides access to a secondary menu. When the button is pressed, several different startup screens may appear depending upon the selected operating mode. If no operating mode has been selected, the first screen to appear will prompt you to select the de-

sired mode Selecting between Transmit and Record Modes The SMWB can be configured as a transmitter or as a recorder. To select the configuration, hold the UP arrow button in then press the power button. Use the UP and DOWN arrow buttons to select the desire mode. Choose Function Xmit Record Use UP and DOWN arrow buttonss to select the function If the Xmit mode is selected, press the MENU/SEL or power button to open the Xmit Main Window in the standby mode. If the Record mode is selected, press the MENU/SEL or power button to open the Record Main Window. Choose Function Xmit Record Use UP and DOWN arrow buttonss to select the function If the mode is set to Xmit (transmitter), the first screen will be the Xmit Main Window Hold for Rf On

...1 Release Power Button before the counter reaches 3 to enter standby mode (no transmission) RF indicator blinks b 19 5 1 494.500

-40

-20 0 NOTE: A brief press of the power button will turn the unit on in the Standby mode with the RF output turned off. Press and hold the power button while an on screen counter steps from 1 to 3 to turn the unit on with the RF output turned on. RF indicator not blinking Hold for Rf On

...3 Hold power button until the counter reaches 3 b 19 5 1 494.500

-40

-20 0 If the mode is set to Record, the first screen to ap-

pear with be the Record Main Window. REC

-40

-20 0 Turning the Power OFF Press and hold the power button counter reaches 1 to turn the unit off. There is also an item in the power menus to turn the unit off (see menu maps in following sections). until the on screen 8 SMWB SeriesLECTROSONICS, INC. Transmitter Operating Instructions Record Mode Operating Instructions Install battery(s) Set the configuration to the Xmit mode (see previ-

ous section) Turn power on in the Standby mode (see previous section) Connect microphone and place it in the position where it will be used. Have user talk or sing at the same level that will be used in the production, and adjust the input gain so that the -20 LED blinks red on louder peaks. Gain Freq Rolloff Compat Gain 25

-40

-20 0 Use the UP and DOWN arrow buttons to adjust the gain until the -20 LED blinks red on louder peaks Signal Level Less than -20 dB

-20 dB to -10 dB

-10 dB to +0 dB

+0 dB to +10 dB Greater than +10 dB

-20 LED

-10 LED Off Green Green Red Red Off Off Green Green Red Set the frequency and compatibility mode to match the receiver. Turn the RF output on with the Rf On? item in the power menu, or by turning the power off and then back on while holding the power button in and wait-

ing for the counter to reach 3. NOTE: The translucent bubble next to the antenna connector is an IR port that can be used to transfer settings from an IR enabled Lectrosonics receiver. Refer to the receiver manual for details. Install battery(s) Set the configuration to the Record mode (see pre-

vious section) Insert microSDHC memory card Turn power on Format memory card Connect microphone and place it in the position where it will be used. Have user talk or sing at the same level that will be used in the production, and adjust the input gain so that the -20 LED blinks red on louder peaks Gain Rolloff Naming SD Info Gain 25

-40

-20 0 Use the UP and DOWN arrow buttons to adjust the gain until the -20 LED blinks red on louder peaks Signal Level Less than -20 dB

-20 dB to -10 dB

-10 dB to +0 dB

+0 dB to +10 dB Greater than +10 dB

-20 LED

-10 LED Off Green Green Red Red Off Off Green Green Red To start recording, press the record button (UP ar-

row button) To stop recording, press and hold the record (UP arrow button) until the word SAVED appears on the screen REC

-40

-20 0 MENU/SEL and UP arrow buttons are labeled by the on screen icons UP arrow button is record start/stop MENU/SEL opens the menu To play back the recordings, remove the memory card and copy the files onto a computer with video or audio editing software installed. 9 Digital Hybrid Wireless Belt-Pack TransmittersRio Rancho, NM Xmit (transmitter) Mode Main Menu b 470 2C 474.500 The Xmit Main Window will appear Selecting the Xmit operating mode (enable RF transmitter):

The selected mode will persist and the unit will boot directly to the Main Window for the selected mode until the mode is changed. To enter mode selection screen, first turn power off, then hold UP arrow and press the power button Choose Function Xmit Record Use arrow keys to select Xmit mode Press MENU/SEL to engage mode

-40

-20 0 From the Main Window press MENU/SEL:

Gain SEL BACK Gain 22 Select from listing Use arrow keys to select input gain Freq. Freq SEL BACK b 21 80 550.400 Press SEL to select desired adjustment Use arrow keys to select desired frequency Rolloff SEL BACK Rolloff 70 Hz Compat SEL BACK Compat Hybrid StepSiz SEL BACK StepSiz Phase SEL BACK Phase TxPower SEL BACK TxPower Default SEL BACK Default settings Select from listing Select from listing 100 kHz 25 kHz Pos. Neg. 25mW 50 mW 100 mW No Yes Use arrow keys to select input gain Use arrow keys to select compatibility mode Use arrow keys to select frequency step size Use arrow keys to select audio output polarity Use arrow keys to select RF power output Use arrow keys to return transmitter to default factory settings 10 SMWB SeriesLECTROSONICS, INC. Xmit (transmitter) Mode Power Menu From the Xmit Main Window press the power button Resume Press SEL to return to the previous screen Pwr Off Press SEL to turn the power off Rf On?

SEL BACK Rf On?

AutoOn?

SEL ProgSw BACK Remote SEL BACK Remote BatType SEL BatType BACK 1.5 V Backlit SEL Backlit BACK Locked SEL BACK Locked?

LED Off SEL LEDs BACK No Yes No Yes Enable Ignore Alk. Lith. On 30 sec 5 min) Yes No On Off Use arrow keys to turn RF signal on/off Use arrow keys to enable auto power restore Use arrow keys to enable/disable remote Use arrow keys to choose battery type Use arrow keys to select LCD backlight duration Use arrow keys to lock/unlock keypad Use arrow keys to turn LEDs on or off About SEL BACK About SMWB v1.00 Displays firmware version 11 Digital Hybrid Wireless Belt-Pack TransmittersRio Rancho, NM Record Mode Main Menu Selecting the Record operating mode:

The selected mode will persist and the unit will boot directly to the Main Window for the selected mode until the mode is changed. To enter mode selection screen, first turn power off, then hold UP arrow and press the power button Choose Function Xmit Record Use arrow keys to select Xmit mode Press MENU/SEL to engage mode REC The Recorder Main Window will appear

-40

-20 0 From the Main Window press MENU/SEL:

Files Files SEL BACK 0014A000 0013A000 Select from listing Use arrow keys to select file in list Format SEL BACK Format?

(erases) No Yes Use arrow keys to initiate formatting the memory card Gain SEL BACK Gain 22 Select value in dB Use arrow keys to select input gain Rolloff SEL BACK Rolloff 70 Hz Select from listing Use arrow keys to select low frequency rolloff Naming SEL BACK Naming Seq #

Clock Use arrow keys to select file naming method SD Info SEL BACK

[SMWB ]

E.........................F 0/ 14G Max Rec Fuel gauge Storage used Storage capacity Available recording time (H : M : S) Default SEL BACK Default settings No Yes Use arrow keys to return recorder to default factory settings 12 SMWB SeriesLECTROSONICS, INC. Record Mode Power Menu From the Record Main Window press the power button Resume Press SEL to return to the previous screen Pwr Off Press SEL to turn the power off AutoOn?

SEL ProgSw BACK Remote SEL BACK Remote BatType SEL BatType BACK 1.5 V Backlit SEL Backlit BACK No Yes Enable Ignore Alk. Lith. On 30 sec 5 min) Use arrow keys to enable auto power restore Use arrow keys to enable/disable remote Use arrow keys to choose battery type Use arrow keys to select LCD backlight duration Clock SEL BACK Clock Year 2017 07 / 26 17 : 19 Month / Day Hour : Minute Locked SEL BACK Locked?

LED Off SEL LEDs BACK Yes No On Off Use arrow keys to lock/unlock keypad Use arrow keys to turn LEDs on or off About SEL BACK About SMWB v1.00 Displays firmware version 13 Digital Hybrid Wireless Belt-Pack TransmittersRio Rancho, NM Setup Screen Details on Xmit Menus Locking/Unlocking Changes to Settings Changes to the settings can be locked. Changing the step size never changes the frequency. It only changes the way the user interface works. If the frequency is set to a fractional increment between even 100 kHz steps and the step size is changed to 100 kHz, the hex code will be replaced by two asterisks on the main screen and the frequency screen. Frequency set to fractional 25 kHz step, but step size changed to 100 kHz. Locked?

Gain 25 Backlit Locked LED Off About No Yes b 19 MUTE 494.525 Freq. b 19

-40

-20 0

-40

-20 0 494.525 A small padlock symbol will appear on adjustment screens when changes have been locked. When changes are locked, several controls and actions can still be used:

Settings can still be unlocked Menus can still be browsed Power can still be turned off by using the power menu or removing the batteries. Main Window Indicators The Main Window displays the band number, Standby or Operating mode, operating frequency, audio level, battery status and programmable switch function. When the frequency step size is set at 100 kHz, the LCD will look like the following. Block number Operating mode Battery status Frequency

(hex number) Frequency (MHz) b 470 2C MUTE 474.500

-40

-20 0 Audio level When the frequency step size is set to 25 kHz, the hex number will appear smaller and may include a fraction. Connecting the Signal Source Microphones, line level audio sources and instruments can be used with the transmitter. Refer to the section entitled Input Jack Wiring for Different Sources for details on the correct wiring for line level sources and microphones to take full advantage of the Servo Bias circuitry. Using Line Level and Instrument Inputs Line level signals can be sent to the input with the proper wiring. Refer to the section on Input Jack Wir-

ing for Different Sources for details. Helpful Features on Receivers To aid in finding clear frequencies, several Lectrosonics receivers offer a SmartTune feature that scans the tun-

ing range of the receiver and displays a graphical report that shows where RF signals are present at different levels, and areas where there is little or no RF energy present. The software then automatically selects the best channel for operation. Lectrosonics receivers equipped with an IR Sync func-

tion allow the receiver to set frequency, step size and compatibility modes on the transmitter via an infrared link between the two units. Note that the frequency has increased by 25 kHz from the upper example. 1/4 = .025 MHz 1/2 = .050 MHz 3/4 = .075 MHz Fraction 1 b 470 42C MUTE 474.525

-40

-20 0 14 SMWB SeriesLECTROSONICS, INC. Adjusting the Input Gain Selecting Frequency The two bicolor Modulation LEDs on the control panel provide a visual indication of the audio signal level entering the transmitter. The LEDs will glow either red or green to indicate modulation levels as shown in the following table. Signal Level Less than -20 dB

-20 dB to -10 dB

-10 dB to +0 dB

+0 dB to +10 dB Greater than +10 dB Off Green Green Red Red Off Off Green Green Red

-20 LED

-10 LED NOTE: Full modulation is achieved at 0 dB, when the -20 LED first turns red. The limiter can cleanly handle peaks up to 30 dB above this point. It is best to go through the following procedure with the transmitter in the standby mode so that no audio will en-

ter the sound system or recorder during adjustment. 1) With fresh batteries in the transmitter, power the unit on in the standby mode (see previous section Turn-

ing Power ON and OFF). 2) Navigate to the Gain setup screen. Gain Freq Rolloff Compat Gain 25

-40

-20 0 3) Prepare the signal source. Position a microphone the way it will be used in actual operation and have the user speak or sing at the loudest level that will occur during use, or set the output level of the in-

strument or audio device to the maximum level that will be used. 4) Use the and arrow buttons to adjust the gain until the 10 dB glows green and the 20 dB LED starts to flicker red during the loudest peaks in the audio. 5) Once the audio gain has been set, the signal can be sent through the sound system for overall level adjustments, monitor settings, etc. 6) If the audio output level of the receiver is too high or low, use only the controls on the receiver to make adjustments. Always leave the transmitter gain ad-

justment set according to these instructions, and do not change it to adjust the audio output level of the receiver. The setup screen for frequency selection offers several ways to browse the available frequencies. Gain Freq Rolloff Compat Freq. b 19 51 494.500 Press MENU/

SEL to select one of four fields to make adjustments Each field will step through the available frequencies in a different increment. The increments are also different in the 25 kHz mode from the 100 kHz mode. Freq. b 19 51 494.500 Freq. b 19 51 494.500 These two fields step in 25 kHz increments when the step size is 25 kHz and 100 kHz increments when the step size is 100 kHz. Freq. These two fields always step in the same increments Freq. 1 block steps b 19 51 494.500 b 19 51 494.500 A fraction will appear next to the hex code in the setup screen and in the main window when the frequency ends in .025, .050 or .075 MHz. 1 MHz steps Freq. b 19 51 1 4 494.525 Fraction appears next to hex code in 25 kHz mode 1 b 470 451 494.525

-40

-20 0 15 Digital Hybrid Wireless Belt-Pack TransmittersRio Rancho, NM Selecting Frequency Using Two Buttons and Hold the MENU/SEL button in, then use the arrow buttons for alternate increments. 100 kHz Mode 1 block steps Selecting the Low Frequency Roll-off Low frequency audio content may be desirable or distracting, so the point at which the roll-off takes place can be set to 35, 50, 70, 100, 120 and 150 Hz. 10 MHz steps 10 MHz steps Freq. b 19 51 494.500 25 kHz Mode Freq. b 19 51 1 4 494.525 1.6 MHz steps to nearest 100 kHz channel 100 kHz steps to next 100 kHz channel 1 block steps 1.6 MHz steps 25 kHz steps If the Step Size is 25 kHz with the frequency set be-

tween even 100 kHz steps and the Step Size is then changed to 100 kHz, the mismatch will cause the hex code to display as two asterisks. Freq. b 19

**

494.500 Step Size and Frequency mismatch b 19 494.525

-40

-20 0 About Overlapping Frequency Bands When two frequency bands overlap, it is possible to select the same frequency at the upper end of one and the lower end of the other. While the frequency will be the same, the pilot tones will be different, as indicated by the hex codes that appear. In the following examples, the frequency is set to 494.500 MHz, but one is in band 470 and the other in band 19. This is done intentionally to maintain compat-

ibility with receivers that tune across a single band. The band number and hex code must match the receiver to enable the correct pilot tone. Freq. b 19 51 494.500 Freq. b470 F4 494.500 Make sure the band number and hex code match the receiver setting Rolloff Compat StepSiz Phase Rolloff 70 Hz Selecting the Compatibility (Compat) Mode When used with a Lectrosonics Digital Hybrid Wireless receiver, the best audio quality will be achieved with the system set to the Hybrid compatibility mode. Rolloff Compat StepSiz Phase Compat NA Hybr Use the UP and DOWN arrows to select the desired mode, then press the BACK button twice to return to the Main Window. Compatibility modes are as follows:

Receiver Models LCD menu item Digital Hybrid Wireless:

Mode 3:*

200 Series:

100 Series:

Mode 7:*

Mode 6:*

IFB Series:

NA Hybr Mode 3 200 Mode 100 Mode Mode 7 Mode 6 IFB Mode Modes 3, 6 and 7 work with certain non-Lectrosonics models. Contact the factory for details. Selecting Step Size This menu item allows frequencies to be selected in either 100 kHz or 25 kHz increments. Rolloff Compat StepSiz Phase StepSiz StepSiz 100 kHz 25 kHz 100 kHz 25 kHz If the desired frequency ends in .025, .050 or .075 MHz, the 25 kHz step size must be selected. 16 SMWB SeriesLECTROSONICS, INC. Normally, the receiver is used to find a clear operat-

ing frequency. All Lectrosonics Digital Hybrid Wireless receivers provide a scanning function to quickly and easily find prospective frequencies with little or no RF interference. In other cases, a frequency may be speci-

fied by officials at a large event such as the Olympics or a major league ball game. Once the frequency is determined, set the transmitter to match the associated receiver. Selecting Audio Polarity (Phase) Audio polarity can be inverted at the transmitter so the audio can be mixed with other microphones without comb filtering. The polarity can also be inverted at the receiver outputs. Rolloff Compat StepSiz Phase Phase Pos. Neg. Setting Transmitter Output Power The output power can be set to 25 mW, 50 mW or 100 mW. Compat StepSiz Phase TxPower TxPower 25 mW 50 mW 100 mW Restoring Default Settings This is used to restore the factory settings. StepSiz Phase TxPower Default Default settings No Yes 17 Digital Hybrid Wireless Belt-Pack TransmittersRio Rancho, NM 5-Pin Input Jack Wiring The wiring diagrams included in this section represent the basic wiring necessary for the most common types of microphones and other audio inputs. Some micro-

phones may require extra jumpers or a slight variation on the diagrams shown. It is virtually impossible to keep completely up to date on changes that other manufacturers make to their products, thus you may encounter a microphone that differs from these instructions. If this occurs please call our toll-free number listed under Service and Repair in this manual or visit our web site at:

www.lectrosonics.com

+5 VDC 1 2 3 4 5 GND 5V SOURCE MIC VOLTAGE SELECT LINE IN m h O 0 0 5 100 Ohm k 1

+

15uF Servo Bias Pin 4 to Pin 1 = 0 V Pin 4 Open = 2 V Pin 4 to Pin 2 = 4 V 200 Ohm 30uF

+

+

3.3uF 10k K 7

. 2 To Audio Amplifier To Limiter Control Backshell with strain relief TA5F Latchlock Insert Insulator Cable clamp Audio input jack wiring:

PIN 1 Shield (ground) for positive biased electret lavaliere microphones. Shield (ground) for dynamic microphones and line level inputs. PIN 2 Bias voltage source for positive biased electret lavaliere microphones that are not using servo bias circuitry and voltage source for 4 volt servo bias wiring. PIN 3 Microphone level input and bias supply. PIN 4 Bias voltage selector for Pin 3. Pin 3 voltage depends on Pin 4 connection. PIN 5 Line level input for tape decks, mixer outputs, musical instruments, etc. Pin 4 tied to Pin 1: 0 V Pin 4 Open: 2 V Pin 4 to Pin 2: 4 V Remove strain relief if using dust boot Dust boot (35510) Backshell without strain relief Note: If you use the dust boot, remove the rubber strain relief that is attached to the TA5F cap, or the boot will not fit over the assembly. 6) If necessary, remove the rubber strain relief from the TA5F backshell by simply pulling it out. 7) Seat the insulator on the insert. Slide the cable clamp over the and of the insulator and crimp as shown on the next page. 8) Insert the assembled insert/insulator/clamp into the latchlock. Make sure the tab and slot align to allow the insert to fully seat in the latchlock. Thread the backshell onto the latchlock. Installing the Connector:

1) If necessary, remove the old connector from the microphone cable. 2) Slide the dust boot onto microphone cable with the large end facing the connector. 3) If necessary, slide the 1/8-inch black shrink tubing onto the mircrophone cable. This tubing is needed for some smaller diameter cables to ensure there is a snug fit in the dust boot. 4) Slide the backshell over the cable as shown above. Slide the insulator over the cable before soldering the wires to the pins on the insert. 5) Solder the wires and resistors to the pins on the insert according to the diagrams shown in Wiring Hookups for Different Sources. A length of .065 OD clear tubing is included if you need to insulate the resistor leads or shield wire. 18 SMWB SeriesLECTROSONICS, INC. Microphone Cable Termination for Non-Lectrosonics Microphones TA5F Connector Assembly Mic Cord Stripping Instructions 1 5 4 2 3 VIEW FROM SOLDER SIDE OF PINS 0.15"

0.3"

Crimping to Shield and Insulation Strip and position the cable so that the clamp can be crimped to contact both the mic cable shield and the insulation. The shield contact reduces noise with some microphones and the insulation clamp increases ruggedness. Shield Insulation Crimp these fingers to contact the shield Crimp these fingers to clamp the insulation NOTE: This termination is intended for UHF transmitters only. VHF transmitters with 5-pin jacks require a different termination. Lectrosonics lavaliere microphones are terminated for compatibility with VHF and UHF transmitters, which is different from what is shown here. 19 Digital Hybrid Wireless Belt-Pack TransmittersRio Rancho, NM Input Jack Wiring for Different Sources In addition to the microphone and line level wiring illus-

trated below, Lectrosonics makes a number of cables and adapters for other situations such as connecting musical instruments (guitars, bass guitars, etc.) to the transmitter. Visit www.lectrosonics.com and click on Accessories, or download the master catalog. A lot of information regarding microphone wiring is also available in the FAQ section of the web site at:

www.lectrosonics.com > SUPPORT > FAQs Follow the instructions to search by model number or other search options. Compatible Wiring for Both Servo Bias Inputs and Earlier Transmitters:

Fig. 1 2 VOLT POSITIVE BIAS 2-WIRE ELECTRET SHIELD A UDI O 3.3 k Compatible wiring for microphones such as Countryman E6 headworn and B6 lavaliere. Fig. 2 4 VOLT POSITIVE BIAS 2-WIRE ELECTRET 1.5 k PIN 1 2 3 4 5 4 3 5 1 2 T A5 F PLUG Most common type of wiring for lavaliere mics. Fully compatible with 5-pin inputs on Lectrosonics transmitters such as the LM and UM Series. Fig. 3 DPA MICROPHONES (Danish Pro Audio miniature models) PIN 1 2 3 4 5 4 3 5 1 2 T A5 F PLUG This wiring is for DPA lavalier and headset microphones. NOTE: The resistor value can range from 3k to 4k ohms. Fig. 4 2 VOLT NEGATIVE BIAS 2-WIRE ELECTRET 2.7 k SHIELD AUDIO Compatible wiring for microphones such as negative bias TRAM models. NOTE: The resistor value can range from 2k to 4k ohms. Fig. 5 4 VOLT POSITIVE BIAS 3-WIRE ELECTRET WITH EXTERNAL RESISTOR Used for 3-wire lavaliere microphones that require an external resistor such as the Sanken COS-11. SHIELD DRAIN (BIAS) SOURCE (AUDIO) This wiring is fully compatible with 5-pin inputs on Lectrosonics transmitters such as the LM and UM Series. This is the wiring for the Lectrosonics M152 lavaliere microphone. Fig. 6 LO-Z MICROPHONE LEVEL SIGNALS XLR JACK For low impedance dynamic mics or electret mics with internal battery or power supply. Insert 1k resistor in series with pin 3 if attenuation is needed 20 Fig. 8 UNBALANCED LINE LEVEL SIGNALS SLEEVE SHIELD A UDI O LINE LEVEL RCA or 1/4 PLUG TIP PIN 1 2 3 4 5 4 3 5 1 2 T A5 F PLUG For signal levels up to 3V (+12 dBu) before limiting. Fully compatible with 5-pin inputs on other Lectrosonics transmitters such as the LM and UM Series. A 20k ohm resistor can be inserted in series with Pin 5 for an additional 20 dB of attenuation to handle up to 30V (+32 dBu). See Line Level Signals on next page Fig. 8 UNBALANCED LINE LEVEL SIGNALS SLEEVE SHIELD A UDI O LINE LEVEL RCA or 1/4 PLUG TIP For signal levels up to 3V (+12 dBu) before limiting. Fully compatible with 5-pin inputs on other Lectrosonics transmitters such as the LM and UM Series. A 20k ohm resistor can be inserted in series with Pin 5 for an additional 20 dB of attenuation to handle up to 30V (+32 dBu). PIN 1 2 3 4 5 4 3 5 1 2 T A5 F PLUG Simple Wiring for Servo Bias Inputs ONLY:

Fig. 9 2 VOLT POSITIVE BIAS 2-WIRE ELECTRET Simplified wiring for microphones such as Countryman B6 Lavalier and E6 Earset models and others. NOTE: This Servo Bias wiring is not compatible with earlier versions of Lectrosonics transmitters. Check with the factory to confirm which models can use this wiring. Fig. 10 2 VOLT NEGATIVE BIAS 2-WIRE ELECTRET Simplified wiring for microphones such as negative bias TRAM. NOTE: This Servo Bias wiring is not compatible with earlier versions of Lectrosonics transmitters. Check with the factory to confirm which models can use this wiring. Fig. 11 4 VOLT POSITIVE BIAS 3-WIRE ELECTRET NOTE: This Servo Bias wiring is not compatible with earlier versions of Lectrosonics transmitters. Check with the factory to confirm which models can use this wiring. SMWB SeriesLECTROSONICS, INC. Microphone RF Bypassing Line Level Signals When used on a wireless transmitter, the microphone element is in the proximity of the RF coming from the transmitter. The nature of electret microphones makes them sensitive to RF, which can cause problems with microphone/transmitter compatibility. If the electret microphone is not designed properly for use with wire-

less transmitters, it may be necessary to install a chip capacitor in the mic capsule or connector to block the RF from entering the electret capsule. Some mics require RF protection to keep the radio sig-

nal from affecting the capsule, even though the trans-

mitter input circuitry is already RF bypassed. If the mic is wired as directed, and you are having dif-

ficulty with squealing, high noise, or poor frequency response, RF is likely to be the cause. The best RF protection is accomplished by installing RF bypass capacitors at the mic capsule. If this is not pos-

sible, or if you are still having problems, capacitors can be installed on the mic pins inside the TA5F connec-

tor housing. Refer to the diagram below for the correct locations of capacitors. Use 330 pF capacitors. Capacitors are available from Lectrosonics. Please specify the part number for the desired lead style. Leaded capacitors: P/N 15117 Leadless capacitors: P/N SCC330P All Lectrosonics lavaliere mics are already bypassed and do not need any additional capacitors installed for proper operation. The wiring for line level and instrument signals is:

Signal Hot to pin 5 Signal Gnd to pin 1 Pin 4 jumped to pin 1 This allows signal levels up to 3V RMS to be applied without limiting. NOTE for line level inputs only (not instrument):

If more headroom is needed, insert a 20 k resistor in series with pin 5. Put this resistor inside the TA5F connector to minimize noise pickup. The resistor will have little or no effect on the signal if the input is set for instrument. Line Level Normal Wiring Line Level More Headroom

(20 dB) See Fig. 8 on previous page 2-WIRE MIC Capacitors next to mic capsule SHIELD AUDIO CAPSULE 3-WIRE MIC SHIELD AUDIO TA5F CONNECTOR BIAS CAPSULE Capacitors in TA5F connector TA5F CONNECTOR 21 Digital Hybrid Wireless Belt-Pack TransmittersRio Rancho, NM 7) If you re-insert the update card and turn the power back on for normal use, the LCD will display a mes-

sage prompting you to format the card:

Format Card?

(files lost) No Yes If you wish to record audio on the card, you must re-format it. Select Yes and press MENU/SEL to format the card. When the process is complete, the LCD will return to the Main Window and be ready for normal operation. If you choose to keep the card as is, you may re-

move the card at this time. The firmware update process is managed by a boot-

loader program - on very rare occasion, you might need to update the bootloader. smwbboot vX_xx.ldr is the bootloader file Follow the same process as with a firmware update and select the smwbboot file. Be forewarned, this can cor-

rupt your unit if interrupted. Dont update the bootloader unless advised to do so by the factory (not for the faint of heart). Firmware Update Firmware updates are made using a microSDHC memory card. Download and copy the following firm-

ware update files to a drive on your computer. smwb vX_xx.ldr is the firmware update file, where X_xx is the revision number. In the computer:

1) Perform a Quick Format of the card. On a Win-

dows-based system, this will automatically format the card to the FAT32 format, which is the Windows standard. On a Mac, you may be given several options. If the card is already formatted in Win-

dows (FAT32) - it will be greyed out - then you do not need to do anything. If the card is in another format, choose Windows (FAT32) and then click Erase. When the quick format on the computer is complete, close the dialogue box and open the file browser. 2) Copy the smwb vX_xx.ldr file to the memory card, then safely eject the card from the computer. In the SMWB:

1) Leave the SMWB turned off and insert the microS-

DHC memory card into the slot. 2) Hold down both the UP and DOWN arrow buttons on the recorder and turn the power on. 3) The recorder will boot up into the firmware update mode with the following options on the LCD:

Update - Displays a scrollable list of the .ldr files on the card. Power Off - Exits the update mode and turns the power off. NOTE: If the unit screen shows FORMAT CARD?, power the unit off and repeat step 3. You were not properly pressing UP, DOWN and Power at the same time. 4) Use the arrow buttons to select Update. Use the UP and DOWN arrow buttons to select the desired file and press MENU/SEL to install the firmware. The LCD will display status messages while the firmware is being updated. 5) When the update is complete, the LCD will display this message: UPDATE SUCCESSFUL REMOVE CARD. After the card is removed, the LCD will return to the three options shown in step 4 above. 6) Select Power Off and press MENU/SEL to finish the update. 22 SMWB SeriesLECTROSONICS, INC. Recovery Process In the event of a battery failure while the unit is re-

cording, a recovery process is available to restore the recording in proper format. When a new battery is installed and the unit is turned back on, the recorder will detect the missing data and prompt you to run the recovery process. The file must be recovered or the card will not be usable in the SMWB. First it will read:

Interrupted Recording Found The LCD message will ask:

Recover?

for safe use see manual You will have the choice of No or Yes (No is selected as the default). If you wish to recover the file, use the DOWN arrow button to select Yes, then press MENU/

SEL. The next window will give you the option to recover all or part of the file. The default times shown are the best guess by the processor where the file stopped record-

ing. The hours will be highlighted and you can either accept the value shown or select a longer or shorter time. If you are unsure, simply accept the value shown as the default. Press MENU/SEL and the minutes are then highlighted. You can increase or decrease the time to be recovered. In most cases you can simply accept the values shown and the file will be recovered. After you have made your time choices, press MENU/SEL again. A small GO!

symbol will appear next to the DOWN arrow button. Pressing the button will initiate the file recovery. The recovery will happen quickly and you will see:

Recovery Successful Special Note:

Files under 4 minutes long may recover with additional data tacked on to the end of the file (from previous recordings or data if the card had been used previ-

ously). This can be effectively eliminated in post with a simple delete of the unwanted extra noise at the end of the clip. The minimum recovered length will be one minute. For example, if the recording is only 20 seconds long, and you have selected one minute there will be the desired 20 recorded seconds with an additional 40 seconds of other data and or artifacts in the file. If you are uncertain about the length of the recording you can save a longer file - there will simply be more junk at the end of the clip. This junk may include audio data recorded in earlier sessions that were discarded. This extra information can be easily deleted in post produc-

tion editing software at a later time. 23 Digital Hybrid Wireless Belt-Pack TransmittersRio Rancho, NM Troubleshooting Symptom:

Transmitter Battery LED off when Power Switch ON No Transmitter Modulation LEDs when Signal Should be Present Receiver Indicates RF But No Audio Receiver RF Indicator Off It is important that you follow these steps in the sequence listed. Possible Cause:

1. Batteries are inserted incorrectly. 2. Batteries are low or dead. 1. Gain control turned all the way down. 2. Batteries are inserted incorrectly. Check power LED. 3. Mic capsule is damaged or malfunctioning. 4. Mic cable damaged or miswired. 5. Instrument Cable damaged or not plugged in. 6. Musical instrument output level set too low. using an alternate source or cable. 1. Audio source or cable connected to transmitter is defective. Try 2. Make sure the compatibility mode is the same on transmitter and 3. Ensure musical instrument volume control is not set to minimum. 4. Check for correct pilot tone indication on the receiver. See item on page 16 entitled About Overlapping Frequency Bands. receiver. frequency, and that the hex code matches. 1. Ensure that the transmitter and receiver are set to the same 2. Transmitter not turned on, or battery is dead. 3. Receiver antenna missing or improperly positioned. 4. Operating distance is too great. 5. Transmitter may be set to the Standby Mode. See page 8. No Sound (Or Low Sound Level), Receiver Indicates Proper Audio Modulation 1. Receiver output level set too low. 2. Receiver output is disconnected; cable is defective or miswired. 3. Sound system or recorder input is turned down. Distorted Sound LEDs on transmitter and receiver while distortion is being heard. system or recorder input. Adjust output level on receiver to the correct level for the recorder, mixer or sound system. 1. Transmitter gain (audio level) is too high. Check Modulation 2. Receiver output level may be mismatched with the sound 3. Transmitter and receiver may not be set to the same compatibility mode. Some mis-matched combinations will pass audio. 4. RF interference. Reset both transmitter and receiver to a clear channel. Use scanning function on receiver if available. Wind Noise or Breath Pops 1. Reposition microphone, or use a larger windscreen, or both. 2. Omni-directional mics produce less wind noise and breath pops than directional types. Hiss and Noise -- Audible Dropouts 1. Transmitter gain (audio level) far too low. 2. Receiver antenna missing or obstructed. 3. Operating distance too great. 4. RF interference. Reset both transmitter and receiver to a 5. Musical instrument output set too low. 6. Microphone capsule picking up RF noise. See item on page 21 clear channel. Use scanning function on receiver if available. entitled Microphone RF Bypassing. Excessive Feedback (With Microphone) and/or reduce receiver output level. 1. Transmitter gain (audio level) too high. Check gain adjustment 2. Microphone too close to speaker system. 3. Microphone is too far from users mouth. 24 SMWB SeriesLECTROSONICS, INC. 470.100 - 537.575 537.600 - 614.375 614.400 - 691.175 Specifications Transmitter Operating Frequencies:

Band A1:

Band B1:

Band C1:

Frequency Selection Steps:

RF Power output:

Pilot tone:

Frequency Stability:

Deviation:

Spurious radiation:

Equivalent input noise:

Input level:

Input impedance:

Input limiter:

Gain control range:

Modulation indicators:

Controls:

Audio Input Jack:

Audio Performance (Digital Hybrid mode) Frequency Response:

THD:

SNR at receiver output:

Mic input:

Line/Instrument:

Selectable; 100 kHz or 25 kHz 25, 50 or 100 mW 25 to 32 kHz; 5 kHz deviation

(Digital Hybrid mode) 0.002%

75 kHz max. (Digital Hybrid mode) 60 dB below carrier 120 dBV (A-weighted) Nominal 2 mV to 300 mV, before limiting Greater than 1V maximum, with limiting. Mic: 300 Ohm Line: 2k Ohm DSP controlled, dual envelope soft limiter with greater than 30 dB range 44 dB; digital control Dual bicolor LEDs indicate modulation of

-20, -10, 0 and +10 dB referenced to full modulation LCD bar graph Side panel membrane switches with LCD interface for power on/off and all setup and configuration controls Switchcraft 5-pin locking (TA5F) 35 Hz to 20 kHz (+/-1dB); low frequency roll-off is selectable at 35, 50, 70, 100, 120, 180 Hz 35 Hz to 20 kHz (+/-1dB) 0.2% (typical) SmartNR OFF NORMAL FULL No Limiting 103.5 107.0 108.5 w/Limiting 108.0 111.5 113.0 Note: The dual envelope soft limiter provides exceptionally good handling of transients using variable attack and release time constants. Once activated, the limiter compresses 30+ dB of transmitter input range into 4.5 dB of receiver output range, thus reducing the measured figure for SNR without limiting by 4.5 dB Storage media:

File format:

A/D converter:

compatibility) Sampling rate:

Recording mode/Bit rate:

Recorder Recording Input Audio Performance Operating temperature range Type:

Input level:

Input connector:

Frequency response:

Dynamic range:

Distortion:

Celsius:

Fahrenheit:

microSDHC memory card*

.wav files (BWF - Broadcast Wave File) 24-bit (with additional 8 bits for wav format 44.1 kHz HD mono mode; 24 bit - 132 kbytes/s Analog mic/line level compatible;

servo bias preamp for 2V and 4V lavaliere microphones Dynamic mic: 0.5 mV to 50 mV Electret mic: Nominal 2 mV to 300 mV Line level: 17 mV to 1.7 V TA5M 5-pin male 20 Hz to 20 kHz; +0.5/-1.5 dB 110 dB (A), before limiting

< 0.035%

-20 to 50

-5 to 122 Specifications subject to change without notice.

*microSDHC Logo is a trademark of SD-3C, LLC Specifications subject to change without notice. Galvanized steel, flexible wire Two AA lithium, disposable Antenna:

Battery:

Battery Life w/ Lithium AA:

SMWB 50 mW (1 AA):

SMWB 100 mW (1 AA):

SMDWB 50 mW (2 AA):

7.25 hrs 5.5 hrs 14.5 hrs SMDWB 100 mW (2 AA):

14 hrs Weight:

Dimensions:

Emission Designator:

5.8 ounces (141 grams), including lithium AA batteries 3.2 x 2.4 x .9 in. (81 x 61 x 20 mm) 180KF3E Specifications subject to change without notice. 25 Digital Hybrid Wireless Belt-Pack TransmittersRio Rancho, NM Service and Repair If your system malfunctions, you should attempt to correct or isolate the trouble before concluding that the equipment needs repair. Make sure you have followed the setup procedure and operating instructions. Check the interconnecting cables and then go through the Troubleshooting section in this manual. We strongly recommend that you do not try to repair the equipment yourself and do not have the local repair shop at-

tempt anything other than the simplest repair. If the repair is more complicated than a broken wire or loose connection, send the unit to the factory for repair and service. Dont attempt to adjust any controls inside the units. Once set at the factory, the various controls and trimmers do not drift with age or vibration and never require readjustment. There are no adjustments inside that will make a malfunctioning unit start working. LECTROSONICS Service Department is equipped and staffed to quickly repair your equipment. In warranty repairs are made at no charge in accordance with the terms of the warranty. Out-of-warranty repairs are charged at a modest flat rate plus parts and shipping. Since it takes almost as much time and effort to determine what is wrong as it does to make the repair, there is a charge for an exact quotation. We will be happy to quote approximate charges by phone for out-of-warranty repairs. Returning Units for Repair For timely service, please follow the steps below:

A. DO NOT return equipment to the factory for repair without first contacting us by email or by phone. We need to know the nature of the problem, the model number and the serial number of the equipment. We also need a phone number where you can be reached 8 A.M. to 4 P.M. (U.S. Mountain Standard Time). B. After receiving your request, we will issue you a return authorization number (R.A.). This number will help speed your repair through our receiving and repair departments. The return authorization number must be clearly shown on the outside of the shipping container. C. Pack the equipment carefully and ship to us, shipping costs prepaid. If necessary, we can provide you with the proper packing materials. UPS is usually the best way to ship the units. Heavy units should be double-boxed for safe transport. D. We also strongly recommend that you insure the equipment, since we cannot be responsible for loss of or dam-

age to equipment that you ship. Of course, we insure the equipment when we ship it back to you. Lectrosonics USA:

Mailing address:

Lectrosonics, Inc. PO Box 15900 Rio Rancho, NM 87174 USA Web:

www.lectrosonics.com Shipping address:

Lectrosonics, Inc. 581 Laser Rd. Rio Rancho, NM 87124 USA E-mail:

sales@lectrosonics.com Telephone:

(505) 892-4501

(800) 821-1121 Toll-free

(505) 892-6243 Fax Lectrosonics Canada:

Mailing Address:

720 Spadina Avenue, Suite 600 Toronto, Ontario M5S 2T9 Telephone:

(416) 596-2202

(877) 753-2876 Toll-free

(877-7LECTRO)

(416) 596-6648 Fax E-mail:

Sales:

Service: joeb@lectrosonics.com colinb@lectrosonics.com 26 SMWB SeriesLECTROSONICS, INC. 27 Digital Hybrid Wireless Belt-Pack TransmittersRio Rancho, NM LIMITED ONE YEAR WARRANTY The equipment is warranted for one year from date of purchase against defects in materials or workmanship provided it was purchased from an authorized dealer. This warranty does not cover equipment which has been abused or damaged by careless handling or shipping. This warranty does not apply to used or demonstrator equipment. Should any defect develop, Lectrosonics, Inc. will, at our option, repair or replace any defective parts without charge for either parts or labor. If Lectrosonics, Inc. cannot correct the defect in your equipment, it will be replaced at no charge with a similar new item. Lectrosonics, Inc. will pay for the cost of returning your equipment to you. This warranty applies only to items returned to Lectrosonics, Inc. or an authorized dealer, shipping costs prepaid, within one year from the date of purchase. This Limited Warranty is governed by the laws of the State of New Mexico. It states the entire liablility of Lectrosonics Inc. and the entire remedy of the purchaser for any breach of warranty as outlined above. NEITHER LECTROSONICS, INC. NOR ANYONE INVOLVED IN THE PRODUCTION OR DELIVERY OF THE EQUIPMENT SHALL BE LIABLE FOR ANY INDIRECT, SPECIAL, PUNITIVE, CONSEQUENTIAL, OR INCIDENTAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THIS EQUIPMENT EVEN IF LECTROSONICS, INC. HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. IN NO EVENT SHALL THE LIABILITY OF LECTROSONICS, INC. EXCEED THE PURCHASE PRICE OF ANY DEFECTIVE EQUIPMENT. This warranty gives you specific legal rights. You may have additional legal rights which vary from state to state. 581 Laser Road NE Rio Rancho, NM 87124 USA www.lectrosonics.com

(505) 892-4501 (800) 821-1121 fax (505) 892-6243 sales@lectrosonics.com 31 July 2017 SMWB_man.indd