FCC ID: 2AB2QLZW36-S Fan&Light Switch

LZW36 | Fan & Light Switch Red Series Thank You. Thank you for taking the chance on us. We are truly humbled to be a part of your smart home journey and know that out of the many companies out there, you trusted us to make your life simpler and we dont take that for granted. Our mission is to provide the best products, with the best customer support, at the best prices. Sure, every company says that... but wed like to think were different. Why? Well, because we have our own smart homes, with our own desires to make our life simpler through home automation. We wake up every day to lights turning on to different colors based on the weather, coffee automatically brewing before we leave for work, and the thermostat changing based on our schedules. We take our nerdiness seriously by engaging in online groups and design our products around community suggestions and needs. We dont pretend to be a multi-billion dollar corporation worried about shareholders and bottom line. Were ok with being the little guy. The underdog, looking out for the best interests of people like us... the everyday smart home enthusiast who is passionate about moving the industry forward and we wouldnt have it any other way. So again, from the bottom of our hearts, thank you for trusting us. Table of Contents:

How Does the Fan & Light Switch Work?

About Z-Wave & Range Estimator Tool Z-Wave Distance Worksheet & Best Practices for Installation Wiring Disclaimers Getting to Know Your Switch (LZW36) Switch & Module Wiring (Neutral Required) Installation Instructions (Canopy Module and In-Wall Switch) Local Configuration Mode Switch Parameters FCC, Warranty and Z-Wave Information Project Hurricane Page:

2 3 4 5 6 7 7-8 8 9

0

Z-Wave SmartStart This device supports Z-Waves new SmartStart feature. Please do not throw out the card within the box that has your unique QR Code with your DSK (Device Specific Key). This QR Code can also be found on the back of the switch (metal plate) and box. HUB Installation Instructions. All HUBs are different, so why should your installation instructions be the same? Below youll find a QR Code to specific instructions for your HUB (NOTE: If you dont see your HUB, please scan the, Other QR Code). As you can imagine, its hard to keep written instructions up to date with all the HUB/App changes, so the most recent instructions will be on the site. However, if youre a manual guy/gal, we get it, please see Page 7 for more details! If ever you run into any issues, please reach out to us at:

contact@inovelli.com. SmartThings Wink Hubitat Other inovelli.com/lzw36/setup/smartthings inovelli.com/lzw36/setup/wink inovelli.com/lzw36/setup/hubitat inovelli.com/lzw36/setup/other www.inovelli.com/lzw36/setup contact@inovelli.com page 

LZW36 | Fan & Light Switch Red Series Technology Behind the Fan & Light Switch There are two different wireless protocols that are used to make this fan & light switch. Z-Wave and RF. Z-Wave is what gives the switch remote (smart) control, whereas RF is what connects the switch to the module. In other words, your hub/gateway connects to your switch, where you can tell it to change the speed of the fan or the brightness of the lights. From there the switch sends an RF command to the module to physically make those commands happen at the fan itself. Z-Wave & RF Distance Notes As mentioned above, there are two different protocols that are used with this switch and module combination. Its important to understand the limitations of the distances of RF and Z-Wave so that your switch and module can communicate effectively. RF (Switch to Fan/Light Module): The maximum distance between the Switch and Module can be 32.8ft (0m) Z-Wave (Switch to Hub): Please see Pages 3 & 4 to calculate the maximum distance NOTE: Please start with your Z-Wave switch first to make sure its within distance and then make sure your module is within distance of the switch. www.inovelli.com/lzw36/setup contact@inovelli.com page 2 Z-Wave Range Worksheet. Feel free to use the below worksheet to give an estimate on where you can put your Z-Wave Switch relative to your HUB (or other Z-Wave repeater). Below is an example of how to use the sheet, using, Example  from Page 3. LZW36 | Fan & Light Switch Red Series For the starting Distance, use 00m. Then look directly from your HUB to wherever youd like to put the outlet and see what obstacles are in the way. Then list those obstacles on the worksheet below (using the charts from Page 2). Best Practices for Pairing the Z-Wave Portion (Wall Switch) to Your Hub/Gateway:

Now that youve read how to calculate the Z-Wave range and have determined the best location to put your switch, its important to understand some best practices of how to pair this device. Below are a few things to keep in mind when you start your individualized pairing instructions (Pages 7-8). NOTE: As mentioned on Page 2, please make sure your switch is within Z-Wave distance first, and then make sure the RF portion

(switch to module) is within distance (max distance apart is 32.8ft or 0m). Calculate the Maximum Distance From the Worksheet Above and Place Well Within That Distance Please use the worksheet above to calculate your maximum distance. This will save us both the headache of offline devices. Remember to add all objects that could potentially be in the way and its our recommendation to be conservative with the distance numbers. If the Switch is Not Including, Try an Exclusion Z-Wave devices can only be included (paired) to one HUB at a time. Sometimes, what happens is that the factory tests the devices by including it to their network and forgets to remove the device from their network, causing the switch to believe that its paired to the factory HUB. While this is extremely rare, it may happen. This can also happen if you purchased this switch used. Follow the exclusion instructions located on Page 8 if you run into issues or check the range to make sure you are within range of the HUB. Or, if youve installed it already, simply hold down the A + B buttons for (5) seconds to see whether or not the switch is within range. If it lights up GREEN and stays GREEN after youve let go, then its within range, however, if it lights up RED, then you are not within range. www.inovelli.com/lzw36/setup contact@inovelli.com page 3 LZW36 | Fan & Light Switch Red Series About Z-Wave. Z-Wave is an incredible technology. With it powering your home, you can choose from over 600 companies and 200 products, all of which will work with each other. The more devices, the more stable the network. The purpose of this portion of the manual is to help you understand how Z-Wave works (in laymans terms) as well as help you organize an efficient Z-Wave network, setting you up for success in the long run. After all, were assuming youll want more than one smart home device!

Z-Wave Network | Using Devices That Repeat Signals. As referenced in the intro, Z-Wave can be used with a few devices or it can be used to build a large network. Below youll see two examples. In the first example, a user has a HUB which is looking for Z-Wave devices within its radius. Z-Wave devices outside this radius will not be found and need to either be moved within the radius or use a repeating device to reach it. The second example shows how a repeater can be used to reach a device outside of the initial radius. Keep this in mind when building your own network and make sure to use the range estimator below. NOTE: Z-Wave range will never be a perfect circle due to walls, furniture, etc. The above is for reference only, please use the, Range Estimator below and the Worksheet on Page 3 for a better idea of where to place your switch or whether or not your chosen location will be in range. Z-Wave Range Estimator. Please use the below information to determine the depreciation of the Z-Wave signal. Z-Wave devices should have a distance of approximately 00m (328ft) without any obstacles in the way. Using the below information, if a signal has to travel through an inner wall, it will lose approximately 40% of its signal. Therefore, 00m multiplied by (00% - 40%) = 60m (97ft). Do this for every wall, window, etc and you will have your approximation. Theres a worksheet on Page 3 that will help. As always, this is just an estimate. Depending on the manufacturers quality for your other Z-Wave products, your signal may vary. www.inovelli.com/lzw36/setup contact@inovelli.com page 4 LZW36 | Fan & Light Switch Red Series Wiring Disclaimers A quick note before we give out the wiring schematics. Please do not try installing this device if you are unsure of how electrical circuits operate within your home. As exciting as it is to have a smart switch installed, it can be dangerous and even life-threatening if you do not install this correctly. Please consult a qualified electrician if necessary as we are unable to give wiring advice outside of schematics. CAUTION - PLEASE ATTENTION -

READ!

VEUILLEZ LIRE SVP!

This device (LZW36) is intended for installation in accordance with the National Electric Code and local regulations in the United States, or the Canadian Electrical Code and local regulations in Canada. If you are unsure or uncomfortable about performing this installation consult a qualified electrician. This product is made for indoor use only and is not designed or approved for use on power lines other than 20VAC, 60Hz, single phase. Attempting to use the LZW36 on non-approved power lines may have hazardous consequences. Cet appareil (LZW36) est conu pour tre install conformment au National Electric Code et aux rglementations locales aux tats-Unis, ou au Canadian Electrical Code et aux rglementations locales au Canada. Si vous ntes pas sr ou mal laise deffectuer cette installation, consultez un lectricien qualifi. Ce produit est conu pour une utilisation en intrieur uniquement et nest pas conu ou approuv pour une utilisation sur des lignes lectriques autres que 20 VCA, 60 Hz, monophas. Tenter dutiliser le LZW36 sur des lignes lectriques non approuves peut avoir des consquences dangereuses. OTHER WARNINGS AUTRES AVERTISSEMENTS Risk of Fire Risk of Electrical Shock Risk of Burns Risque dincendie Risque de choc lectrique Risque de brlures MEDICAL EQUIPMENT QUIPEMENT MDICAL Please DO NOT use this switch to control Medical or Life Support equipment. Z-Wave devices should never be used to control the On/Off status of Medical and/or Life Support equipment. Veuillez NE PAS utiliser cet interrupteur pour contrler lquipement mdical ou de survie. Les appareils Z-Wave ne doivent jamais tre utiliss pour contrler ltat On / Off des quipements mdicaux et / ou de survie. RECOMMENDED INSTALLATION PRACTICES PRATIQUES DINSTALLATION RECOMMANDES Use only indoors or in an outdoor rated box Utiliser uniquement lintrieur ou dans une bote classe extrieure Turn off the circuit breaker -- Installing this switch and module with the power on will expose you to dangerous voltages Connect only copper or copper-clad wire to the switch or module To reduce the risk of overheating and possible damage to other equipment, use the LZW36 load output to control no more than 200 watts (Incandescent) or 00W (LED/CFL) plus no more than 

Amp of Fan load. Dimming an inductive load (by connecting to the light load wire), such as a fan or transformer, could cause damage to the dimmer, the load bearing device, or both. To install your Fan/Light Switch, youll need to identify the following four wires:

- Line: Usually black and can also be called the HOT or LIVE, and carries

20VAC electricity into the electrical box

- Neutral: Usually white and is commonly daisy chained from box to box, usually appearing as a white wire bundle

- Load: Usually black, blue or red

- Ground: Bare copper wire or metal fixture (if grounded) If you are having difficulties identifying wires, please consult an electrician. teignez le disjoncteur - Linstallation de cet interrupteur et de ce module sous tension vous exposera des tensions dangereuses Connectez uniquement du fil en cuivre ou en cuivre au commutateur ou au module Pour rduire le risque de surchauffe et les dommages possibles dautres quipements, utilisez la sortie de charge LZW36 pour contrler pas plus de 200 watts (incandescent) ou 00W (LED /

CFL) plus pas plus de  ampre de charge de ventilateur. La gradation dune charge inductive (en la connectant au fil de charge lgre), comme un ventilateur ou un transformateur, pourrait endommager le gradateur, le dispositif de support de charge ou les deux. Pour installer votre interrupteur ventilateur

/ clairage, vous devez identifier les quatre fils suivants:

- Ligne: gnralement noire et peut galement tre appele HOT ou LIVE, et transporte de llectricit 20VAC dans le botier lectrique

- Neutre: gnralement blanc et est gnralement connect en guirlande dune bote lautre, apparaissant gnralement sous la forme dun faisceau de fils blancs

- Charge: gnralement noire, bleue ou rouge

- Masse: fil de cuivre nu ou luminaire mtallique (si mis la terre) Si vous prouvez des difficults identifier les fils, veuillez consulter un lectricien. PLEASE NOTE: As of 05/25/9, we are unable to provide electrical and/or wiring advice outside of our schematics. If you are unable to read a schematic or are not familiar with wiring, we suggest hiring an electrician. We apologize for any inconvenience. Bulb Compatibility: Well keep a list of compatible bulbs in our community which can be found here:

https://support.inovelli.com/portal/kb/articles/lzw36-fan-light-switch-compatible-bulbs www.inovelli.com/lzw36/setup contact@inovelli.com page 5 LZW36 | Fan & Light Switch Red Series Getting to Know Your LZW36 Fan Switch Now that youre familiar with Z-Wave and how it works, its time to understand the basics of your new smart switch. For more advanced configurations, please see Pages 8-0. A. Light Dimmer (and Scene Control*): This button can be used to increase or decrease the dimness level on your light. Press (hold) up to increase brightness and press (hold) down to decrease the brightness. Also, a single press will send a scene command to your hub. B. Light On/Off Button (and Scene Control*): Press this button to turn on and off the fan light(s). This button can also be used to trigger Z-Wave scenes. You may add up to 7 scenes (Tap x, 2x, 3x, 4x, 5x, Hold, Release). C. Light RGB LED Bar (with Notifications*): Shows the level at which the fan light(s) are set at. In addition, it can be used as a notifier for various events (i.e.: turn purple if front door is open). D. Fan Speed (and Scene Control*): This button can be used to increase or decrease the speed of your fan. Press (hold) up to increase the speed and press (hold) down to decrease the speed. Also, a single press will send a scene command to your hub. E. Fan On/Off Button (and Scene Control*): Press this button to turn on and off the fan. This button can also be used to trigger Z-Wave scenes. You may add up to 7 scenes (Tap x, 2x, 3x, 4x, 5x, Hold, Release). Button Combination Cheat Sheet Button Combination Result Hold A + B for 0 Seconds Enter Local Config Mode Hold A + Tap B 2x Hold D + Tap E 2x Hold A + Tap B 3x Hold D + Tap E 3x Hold A + Tap B 8x Hold D + Tap E 8x Dismiss Light Notification Dismiss Fan Notification Enter Z-Wave Inclusion /

Exclusion Mode Enter Fan Module Pairing Mode Enable Local Protection on Light Buttons (Disable Relay) Enable Local Protection on Fan Buttons (Disable Relay) Detect Z-Wave Network Signal Hold A + B for 5 Seconds Hold A + B for 20 Seconds Z-Wave Factory Reset Hold D + E for 20 Seconds Fan Module Factory Reset F. Light RGB LED Bar (with Notifications*): Shows the level at which the fan speed is set at. In addition, it can be used as a notifier for various events (i.e.: turn red when your alarm is armed). G. Air Gap Switch: This will reboot the switch if it needs to be rebooted (NOTE: The air-gap switch will not cut power to the module). NOT SHOWN: Energy Monitoring* and Scene Control* are built-in features of this switch as well. A D B E C F Getting to Know Your LZW36 Fan Module H I J K H. Line Wire (Black): This wire will be what powers the module. I. Neutral Wire (White): This is needed to keep power to the RF chip. J. Light Load (Blue): This is what connects to the fans light wire. G K. Fan Load (Red): This is what connects to the fans motor wire. L. RF Antenna: This is the modules RF antenna. L NOTE: If power is cut to the switch and module, it will take approximately 30 seconds to reconnect. Full wires not shown

* Please make sure your HUB supports these features. See website for more details. www.inovelli.com/lzw36/setup contact@inovelli.com page 6 LZW36 | Fan & Light Switch Red Series Wiring Instructions: Neutral Wire Required (Quick Notes) Please note that you will need a neutral wire in order to install this switch. In addition, you will be connecting the Line/Hot to the Load. Here are some quick notes to read prior to installing your switch:

If you do not see your wiring diagram here, please check online as we will constantly update and add schematics to our site and also have a forum where you can help each other. Again, we can no longer provide specific wiring or electrical help. This switch will not work in a 3-Way (or multi-switch) setting. see inovelli.com/lzw36-wiring for more schematics Installing the Fan Module in the Fan Bracket Your fan module should fit snuggly in the fan bracket that helps hold your fan to the ceiling. Including (Pairing) Your Switch & Module: General Instructions Below are step by step instructions on how to pair your fan switch and fan module. For hub specific instructions, please use the QR codes or URLs on Page . Step 1: Gather Your Materials, Find an Appropriate Location, and Install the Fan Switch Materials Needed: Wire nuts, screwdriver, and access to both the line (hot) and neutral wires. Locate an area to install your switch within the recommended distance (Pages 3-4) from your HUB/Gateway. Walls, furniture, and other obstructions may degrade the communication between the Switch and your HUB/Gateway, so please keep this in mind when selecting a location. Before cutting power to your switch and fan, using the fans pull chains, set the fan to the highest speed and turn the light(s) on. Moving forward you will no longer need to use the pull chains to control the fan or light(s). Follow the wiring instructions on page 7 -- REMEMBER: TURN OFF ELECTRICITY BEFORE INSTALLATION!

www.inovelli.com/lzw36/setup contact@inovelli.com page 7 Continued on next page . LZW36 | Fan & Light Switch Red Series NOTE: If youd like to verify if the switch is within range of your Z-Wave hub before installing the canopy module, feel free to turn the power back on. The switch should light up and run through a series of colors before finally turning blue. Once the switch LED bars are blue, hold down the top of Button A and Button B for 5 seconds and the switch LEDs will turn Green. Release the buttons and if the switch LEDs remain Green, then the switch is within Z-Wave range. If the LED bars turn Red, then the switch is not within range. Step 2: Installing the Fan Canopy Module Materials Needed: Wire nuts, screwdriver, access to a neutral (white), load (black), fan and light wires and the included zip-tie. Ensure the distance between your fan switch and module is no more than 32.8ft (0m) as that is the maximum distance the RF signal can travel from the switch to the canopy module. Remove your ceiling fan from the electrical box and identify the load (black -- which is now hot), neutral (white), and the fan motor and light loads (usually red is the fan and blue is the light, but your wires may be different). Connect the wires together as shown on Page 7 or as shown in Figure .. Once completed, its time to check to make sure everything works and is paired correctly. Please fasten the canopy to the fan bracket using the included zip-tie (as shown on page 7), ensure all connections are secure with no exposed copper and re-assemble your fan. Step 3: Pairing the Switch to the Canopy Module Now that everything is installed, and your fan is re-assembled its time to pair the switch to the canopy module. NOTE: The fan module should be paired to the Z-wave switch from the factory. In case you have an issue, below is how you can manually do so. Warning: Do not try to test the fan without it being secured to the ceiling. Avertissement: Nessayez pas de tester le ventilateur sans quil soit fix au plafond. With the fan secured to the ceiling and the switch secured to the wall, lets start the pairing process of the switch and module. To pair the switch to the module, apply power from the circuit breaker to both devices. Note: After trying to pair to the Z-Wave switch for 30 seconds, if not successful, the fan module goes into pairing mode for 2 minutes. You can tell it is in this mode by the bulb in the fixture pulsing. Press and hold Button D and press Button E 3x. If successful, the LED bar will blink Green. You should now be able to control the fan speed and light brightness from the switch manually. Press Buttons B & E to turn the fan and light on and off, and hold up and down Buttons A & D to change the fan speed and light dim level. Having Problems Including? Try an Exclusion Figure .

Step 4: Pairing the Switch to Your Hub/Gateway Now that your switch and canopy module are paired, its time to pair your switch to your Z-Wave enabled hub or gateway. Place your hub or gateway into exclusion mode. Then:

Enable the inclusion process on your Hub or Gateway. Hold down button A and press button B 3x quickly and your LED Bars will pulse blue signifying the switch is in inclusion mode. If successful, the switch LED Bars will flash Green and if unsuccessful, the LED Bars will flash Red. If the LED Bars flash Red, please check your Z-Wave signal by referencing the Note at the top of the page. If your switch is within range, you may want to try an exclusion. Instructions are to the right. Hold button A + Press Button B 3x. If it is successful the LED will blink green. Then, try including again. Switch (Local) Configuration Mode There are a couple different ways you can set the configuration parameters of your switch (listed on page 9). It is recommended that you set them from your hub when possible, but if not, you can set them directly from the switch! For more detailed instructions, please check our support webpage at support.inovelli.com. Here are some basic instructions:

Enter into either light configuration mode or fan configuration mode based on which parameters you want to edit. Light: Hold down the A Use the light level up/down (A) or fan level up/down (D) buttons to set the parameter to the number you would like. Each press Press either the light on/off button (B) or the fan on/off button (E) the number of times that corresponds with the parameter you want

. Button + B Button for 10 Seconds. Fan Hold down the D Button + E Button for 10 Seconds. 2. to change (listed on page 9). 3. increments the value by . The LED on the switch will flash yellow to show you which parameter number you are editing. The LED will also flash purple to show you 4. the value that you have assigned. A long flash represents 0s and a short flash represents s. So, for example, two long flashes followed by three short flashes would represent 23. 5. seconds to save and exit. After you are finished, press and hold JUST the B or E button (depending on whether you are editing the light or fan configuration) for 0 www.inovelli.com/lzw36/setup contact@inovelli.com page 8 LZW36 | Fan & Light Switch Red Series Switch Parameters Below youll find the various parameters associated with your switch. There are a ton of options for customization and as you can imagine, its hard to write out all the possibilities in a manual. Please use this as a guide, but also feel free to check out our site where well give some specific examples using each parameter. Param # Change at the switch?

Switch Config #

Light or Fan Name Description Size Range Default

Dimming Speed This changes the speed in which the attached light dims up or down. A setting of 0 should turn the light immedi-

ately on or off (almost like an on/off switch). Increasing the value should slow down the transition speed.

2 3 4 5 6 7 8 9

0

2

3

4

5

6

7

8

9 20 2

22 23 24 25 26 27 28 29 30 Yes No No No Yes Yes Yes Yes Yes No No Yes Yes Yes No Yes Yes Yes Yes Yes Yes Yes Yes No No Yes Yes No No No L L L L L L F F L L F L L F F L F L L F F L F L F L F Dimming Speed

(From Switch) Ramp Rate This changes the speed in which the attached light dims up or down when controlled from the physical switch. A setting of 0 should turn the light immediately on or off (almost like an on/off switch). Increasing the value should slow down the transition speed. A setting of 99 should keep this in sync with parameter . This changes the speed in which the attached light turns on or off. For example, when a user sends the switch a basicSet(value: 0xFF) or basicSet(value: 0x00), this is the speed in which those actions take place. A setting of 0 should turn the light immediately on or off (almost like an on/off switch). Increasing the value should slow down the transition speed. A setting of 99 should keep this in sync with parameter . Ramp Rate (From Switch) This changes the speed in which the attached light turns on or off from the physical switch. For example, when a user presses the up or down button, this is the speed in which those actions take place. A setting of 0 should turn the light immediately on or off (almost like an on/off switch). Increasing the value should slow down the transition speed. A setting of 99 should keep this in sync with parameter . The minimum level that the dimmer allows the bulb to be dimmed to. Useful when the user has a bulb that does not turn on at a lower level. The maximum level that the dimmer allows the bulb to be dimmed to. Useful when the user has an LED bulb that reaches its maximum level before the dimmer value of 99. 55..99 99 The minimum level that the dimmer allows the fan to be dimmed to. Useful when the user has a fan that does not turn on at a lower level. Maximum Level The maximum level that the dimmer allows the fan to be dimmed to. 55..99 99 Invert Switch Inverts the switch (Tap Down = On, Tap Up = Off). 0 = Disabled,  = Enabled Minimum Level Maximum Level Minimum Level Auto Off Timer Auto Off Timer Automatically turns the light off after this many seconds. When the switch is turned on a timer is started that is the duration of this setting. When the timer expires, the switch is turned off. Automatically turns the fan off after this many seconds. When the fan is turned on a timer is started that is the duration of this setting. When the timer expires, the fan is turned off. Default Level (Local) Default level for the dimmer when it is powered on from the local switch. A setting of 0 means that the switch will return to the level that it was on before it was turned off. Default Level (Z-

Wave) Default level for the dimmer when it is powered on from a Z-Wave command. A setting of 0 means that the switch will return to the level that it was on before it was turned off. Default Level (Local) Default level for the fan when it is powered on from the local switch. A setting of 0 means that the switch will return to the level that it was on before it was turned off. Default Level (Z-

Wave) Default level for the fan when it is powered on from a Z-Wave command. A setting of 0 means that the switch will return to the level that it was on before it was turned off. After Power Restored The state the switch should return to once power is restored after power failure. 0 = off, -99 = level, 00=previous. After Power Restored The state the switch should return to once power is restored after power failure. 0 = off, -99 = level, 00=previous. LED Indicator Color This is the color of the Light LED strip represented as part of the HUE color wheel. Since the wheel has 360 values and this parameter only has 255, the following equation can be used to determine the color: value/255 * 350 = Hue color wheel value LED Strip Intensity This is the intensity of the Light LED strip. LED Indicator Color This is the color of the Fan LED strip represented as part of the HUE color wheel. Since the wheel has 360 values and this parameter only has 255, the following equation can be used to determine the color: value/255 * 350 = Hue color wheel value LED Strip Intensity This is the intensity of the Fan LED strip. LED Strip Intensity

(When OFF) This is the intensity of the Light LED strip when the switch is off. This is useful for users to see the light switch location when the lights are off. LED Strip Intensity

(When OFF) This is the intensity of the Fan LED strip when the switch is off. This is useful for users to see the light switch loca-

tion when the lights are off. LED Strip Effect LED Strip Effect LED Strip Timeout LED Strip Timeout This will allow you to add some sweet effects to your LED Bar (i.e.: pulse, chase, solid, etc). Byte  = Color, Byte 2 =

Brightness Level, Byte 3 = Effect, Byte 4 = Duration. *Please see website for further instructions on how to set this up This will allow you to add some sweet effects to your LED Bar (i.e.: pulse, chase, solid, etc). Byte  = Color, Byte 2 =

Brightness Level, Byte 3 = Effect, Byte 4 = Duration. *Please see website for further instructions on how to set this up When the LED strip is disabled (Light LED Strip Intensity is set to 0), this setting allows the LED strip to turn on temporarily while being adjusted. When the LED strip is disabled (Fan LED Strip Intensity is set to 0), this setting allows the LED strip to turn on temporarily while being adjusted. L/F Active Power Reports The power level change that will result in a new power report being sent. The value is a percentage of the previous 0..00

0 report. 0 = disabled. L/F Periodic Power &

Energy Reports Time period between consecutive power & energy reports being sent (in seconds). The timer is reset after each report is sent. L/F Energy Reports Energy level change which will result in sending a new energy report. Available settings: -27 (0.0-.27 kWh) 0 =

disabled.

2 2 2

2

4 4

2

0..98 3 0..99 99 0..99 99 0..99 99

..45

..45 0..

0.. 32767 0.. 32767

..99

..99

..99

..99 0..00 0..00 0..255 0..0 0..255 0..0 0..0 0..0 Varies *

Varies *

0..0 0..0

0 0 0 0 0 0 0 5

0 0 3 3

00 0

70 5

70 0.. 32767 0..00 3600

0 page 9 2 3

2 4 5 6 3 7 4 8 9 5 6

0 7

8 www.inovelli.com/lzw36/setup contact@inovelli.com LZW36 | Fan & Light Switch Z-Wave Command Classes 5E - COMMAND_CLASS_ZWAVEPLUS_INFO 55 - COMMAND_CLASS_TRANSPORT_SERVICE 98 - COMMAND_CLASS_SECURITY 9F - COMMAND_CLASS_SECURITY_2 6C - COMMAND_CLASS_SUPERVISION 26 - COMMAND_CLASS_SWITCH_MULTILEVEL 70 - COMMAND_CLASS_CONFIGURATION 85 - COMMAND_CLASS_ASSOCIATION 59 - COMMAND_CLASS_ASSOCIATION_GRP_INFO 86 - COMMAND_CLASS_VERSION 72 - COMMAND_CLASS_MANUFACTURER_SPECIFIC 5A - COMMAND_CLASS_DEVICE_RESET_LOCALLY 73 - COMMAND_CLASS_POWERLEVEL 75 - COMMAND_CLASS_PROTECTION 22 - COMMAND_CLASS_APPLICATION_STATUS 7A - COMMAND_CLASS_FIRMWARE_UPDATE_MD 5B - COMMAND_CLASS_CENTRAL_SCENE_V3 8E - COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V2 87 - COMMAND_CLASS_INDICATOR 60 - COMMAND_CLASS_MULTI_CHANNEL_V4 Group2 (Light) Group5 (Fan) Group3 (Light) Group6 (Fan) Group4 (Light) Group7 (Fan) Z-Wave Association Groups Group #

Group 

Max Nodes Commands 5 5 5 5

. Central Scene 2. Basic Report 3. Multilevel Report 4. Protection Report 5. Device Reset Locally 6. Meter Report Basic Set Switch Multilevel Set Switch Multilevel Set Red Series Resetting Your Device You may hold the Light Level Button (A) + Light On/Off Button

(B) for 20 seconds or use a certified controller to remove the device from your network to factory default. Only use this procedure in the event that the network primary controller is missing or otherwise inoperable. OTA NOTE Over-the-Air updates are available on this switch. It will take about 

minute after completion for it to, settle, so please leave the switch alone for a minute after flashing. If the power is cut off immediately after OTA is completed, OTA may fail. Group 1: Lifeline -- Members of this group will receive unsolicited messages related to the status of the switch. Group 2: Basic Set - Light -- Sends On & Off commands to associated devices. (1. Single press UP button sends BasicSet (0xFF) and 2. Single press Down sends BasicSet (0x00) Group 3: Switch Multilevel Set - Light -- Sends set level commands to associated devices when switch is pressed.

(1. Hold & Release Up or Down button sends SwitchMultiLevelSet which keeps associated devices in sync with this device. 2. Single press Up button sends SwitchMultiLevelSet(0x FF) and 4. Single press Down button sends SwitchMultiLevelSet(0x00) Group 4: Switch Multilevel Set - Light -- Sends start / stop level change to associated devices.

(1. Hold Up button sends SW_MULTILEVEL_START_LEVEL_CHANGE (Up) 2: Hold Down button sends SW_MULTILEVEL_START_LEVEL_CHANGE (Down) 3. Release Either button sends SW_MULTILEVEL_STOP_LEVEL_CHANGE Group 5: Basic Set - Fan -- Sends On & Off commands to associated devices. (1. Single press UP button sends BasicSet (0xFF) and 2. Single press Down sends BasicSet (0x00) Group 6: Switch Multilevel Set - Fan-- Sends set level commands to associated devices when switch is pressed.

(1. Hold & Release Up or Down button sends SwitchMultiLevelSet which keeps associated devices in sync with this device. 2. Single press Up button sends SwitchMultiLevelSet(0x FF) and 4. Single press Down button sends SwitchMultiLevelSet(0x00) Group 7: Switch Multilevel Set - Fan -- Sends start / stop level change to associated devices.

(1. Hold Up button sends SW_MULTILEVEL_START_LEVEL_CHANGE (Up) 2: Hold Down button sends SW_MULTILEVEL_START_LEVEL_CHANGE (Down) 3. Release Either button sends SW_MULTILEVEL_STOP_LEVEL_CHANGE Federal Communications Commission (FCC) Statement FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate this equipment. This device complies with Part 5 of the FCC Rules. Operation is subject to the following two conditions: () This device may not cause harmful interference, and (2) this device must accept any interference received including interference that may cause undesired operation. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 5 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna, increase the separation between the equipment and receiver, connect the equipment into an outlet on a circuit different from that to which the receiver is connected or consult the dealer or an experienced radio/TV technician for help. This equipment should be installed and operated with minimum distance 8in (20cm) between the radiator and your body. IC Caution: This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: () this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. DECLARATION DE CONFORMITE DINDUSTRIE CANADA: Ce priphrique a t test et reconnu conforme aux limites spcifies dans RSS-20. Son utilisation est soumise aux deux conditions suivantes: () il ne doit pas provoquer dinterfrences gnantes et (2) il doit tolrer les interfrences re.ues, notamment cellessusceptibles den perturber le fonctionnement. Cet quipement doit tre install et utilis une distance minimale de 20 cm entre le radiateur et votre corps. Warranty and Specifications Warranty: Inovelli will replace any defective unit for the lifetime of the unit, pending the unit was used in the manner it was intended to. Please email us at:

contact@inovelli.com or visit us at www.inovelli.com/warranty for full details. Specifications for Model # LZW36:

Power: 20V AC, 60Hz, Signal (Frequency): 908.42 MHz, Operating Temperature Range: 32-95 F (0-35 C) Maximum Load: 200W Incandescent, or 00W LED / CFL Range: Up to 00 meters line of sight between the Wireless Controller (HUB) and the closest Z-Wave Module For indoor use. Specifications subject to change without notice due to continuing product improvement. Approval: UL Listed / FCC / IC / Z-Wave Plus Certified CAN ICES-003 (B)/NMB-003(B) www.inovelli.com/lzw36/setup contact@inovelli.com page 0 LZW36 | Fan & Light Switch Red Series Project Hurricane You may have noticed our signatures and project name on the inside of the box and wondered, what is that all about?. Well, great question! All of our products have a project name associated with them that means something to us and speaks directly to the device itself. Its personality if you will. In addition to the project name, our signatures indicate that weve all signed off on the project. We believe in the project and worked hard, along with you, to bring it to life. Project, Hurricane has a couple of meanings to it. The first meaning was that this device was one of the first smart home products ever requested by the community, even before Inovelli started. I was attending the University of Miami (Hurricanes) and one of the projects we had to do involved smart home products. I put a poll out to see what the most requested product was that doesnt exist yet and the fan/light combo was it. So, project, Hurricane is a shout out to my alma-mater as without us doing a project in class, Inovelli (and project, Hurricane) wouldnt exist. The other meaning is just silly in that its a fan that creates breeze and of course Hurricanes produce wind. Anyway, thank you not only for your support, but for helping us put out the first Z-Wave Fan & Light module. A special thank you goes out to our Beta Testers as well, we couldnt have done it without you!

Project Hurricane has been my favorite innovation project to work on. Its been something Ive wanted personally ever since I began my smart home journey. Ive been able to automate everything in my house except these darn fans and, of course, its the one thing my daughters always leave on!

Anyway, were super pumped to be the first to offer these in Z-Wave and hope you like them too. Eric H. Founder / CEO This has been an exciting project for me. It will be our first Z-Wave 700 series product to go to market and is one of (if not) the first in the industry. Other than being the first in that regard, It has an innovative design that utilizes Z-Wave & RF to provide a compact product that solves a need that has been in the smart home market for many years. Inovelli customers can rejoice knowing that they finally have a highly capable device to control the fans in their home. The fan and light switch is going to be huge for the smart home industry. There are so many ceiling fans out there that just want a little automation in their lives! The part Im most excited about is the scenes, notifications and all the other bells and whistles that come with this switch. Finally, the fact that we had an entire group of community beta testers testing this has been amazing. Working with the team on this was so much fun. Watching everyone get excited about making something that has been asked for going on three years now from the community was truly an amazing experience. I cant wait to start posting on social, sending out emails and letting the world know about these switches!

This project holds a special place in my heart in that it was the first one I really got to manage on my own. It had its fair share of challenges (literally a pandemic happening) but weve pulled through and came out with a pretty awesome product thats being used in my own smart house! It was also really cool to work with the community to bring this project to life -- it really felt like a team effort. Eric M. CTO Nathan CSO Brianna Sr. Marketing Manager Courtney Operations Manager www.inovelli.com/lzw36/setup contact@inovelli.com page 

E 513509 FCC ID: 2AB2QLZW36-S IC: 10256A-LZW36S Fan+Light Switch Model No. LZW36-S Use copper conductors only Indoor dry location use only Ceiling fan only

Date: _2020-02-19_______ TUV Rheinland Group 762 Park Avenue Youngsville, NC 27596 To Whom It May Concern:

Authority to Act as Agent I appoint TUV Rheinland (Shenzhen) Co., Ltd. to act as our agent in the preparation of this application for equipment certification. I certify that submitted documents properly describe the device or system for which equipment certification is sought. I also certify that each unit manufactured, imported or marketed, as defined in the FCC or Industry Canadas regulations will have affixed to it a label identical to that submitted for approval with this application. For instances where our authorized agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for Certification, as specified by TUV Rheinland Group, still resides with ___( LEEDARSON LIGHTING CO., LTD. and Xingda Road, Xingtai Industrial Zone, Changtai County, Zhangzhou, Fujia, China)___. For TCB applications, We certify that we are not subject to denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. Further, no party, as defined in 47 CFR 1.2002 (b), to the application is subject to denial of federal benefits, that includes FCC benefits. Thank you, Agency Agreement Expiration Date: _____ 12 months____ By:

(Signature) _______Vick Zhang___________

(Print name) Title:

____ safety engineer _____Telephone +86-592-3699897______ On behalf of: LEEDARSON LIGHTING CO., LTD.

(Company Name) QF094234 Page 1 of 1 Revision 0

Date: 2019-03-24 Confidentiality Letter Subject: Confidentiality Request for FCC ID: 2AB2QLZW36-S and IC ID: 10256A-LZW36S Pursuant to FCC 47 CRF 0.457(d) and 0.459 and IC RSP-100, Section 10, the applicant requests that a part of the subject FCC/IC application be held confidential. Type of Confidentiality Requested Short Term Short Term Short Term Short Term Short Term Short Term Short Term Short Term Permanent Permanent Permanent Permanent Permanent Permanent Exhibit Block Diagrams External Photos Internal Photos Operation Description/Theory of Operation Part List/Tune-Up Procedure Schematics Test Setup Photos Users Manual LEEDARSON LIGHTING CO., LTD. has spent substantial effort in developing this product and it is one of the first of its kind in industry. Having the subject information easily available to "competition" would negate the advantage they have achieved by developing this product. Not protecting the details of the design will result in financial hardship. Permanent Confidentiality:

The applicant requests the exhibits listed above as permanently confidential be permanently withheld from public review due to materials that contain trade secrets and proprietary information not customarily released to the public. Short-Term Confidentiality:

The applicant requests the exhibits selected above as short term confidential be withheld from public view for a period of 180 days from the date of the Grant of Equipment Authorization and prior to marketing. This is to avoid premature release of sensitive information prior to marketing or release of the product to the public. Applicant is also aware that they are responsible to notify TUV Rheinland in the event information regarding the product or the product is made available to the public. TUV Rheinland will then release the documents listed above for public disclosure pursuant to FCC Public Notice DA 04-

1705. Sincerely, By:

(Signature/Title) Vick Zhang

(Print name)