Installation Instruction Packaging contents:
LED Retrofit kit: 1pcs Installation Instruction: 1pcs Friction bracket: 2pcs E26 lamp base: 1pcs Remot:1pcs WARNING WARNING Risk of fire or electric shock. LED Retrofit Kit installation requires knowledge of luminaires electrical systems. If not qualified, do not attempt installation. Contact a qualified electrician. WARNING Risk of fire or electric shock. Install this kit only in the luminaires that have the construction features and dimensions shown in the photographs and/or drawings and where the input rating of the retrofit kit does not exceed the input rating of the luminaire. Do not make or alter any open holes in an enclosure of wiring or electrical components during kit installation. WARNING To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or other sharp objects. WARNING This device is not intended for use with emergency exits. WARING- DO NOT USE WITH STANDARD DIMMERS WARING- -SUITABLE FOR WET LOCATIONS Federal Communications Commission (FCC) Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that may cause undesired operation. The grantee is not responsible for any changes or modifications not expressly approved by the party responsible for compliance. Such modifications could void the users authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance of 20 cm between the radiator and your body. Only use the control provided with the instruction to control this lamp. This lamp will not operate properly when connected to a standard dimmer or dimming control The product is intended to retrofit Type IC or Type non-IC recessed mount Listed luminaires that use one lamp with or without a diffuser. The minimum lamp compartment dimensions are tabulated below:
LampcompartmentofLuminaire,overall dimensions,mm Electrical parameters:
Diameter Height 189.5 70 ModelNO. Inputvoltage(V) Frequency(Hz) Input Input wattage(W) Current(mA) NS01RA13FR125zx 120 60 13
* x replaced by one digital numbers range 1 to 9 to denote different package style; z replaced by one digital numbers 8/9 to denote different CRI ize:
Product si Unit: mm on steps:
power befor the shallow ve the adjust whousingsoc ethetorsions nbrackets)be re servicing. housing able socket cketbracket) springsintot eforeinstallin bracket to as
). thefrictionbr ngtheLEDRe Remove the e existing bul b or remove the existing trim if neces ssary. ssureenough hspaceforth efixture(ass showninHow wtoadjust rackets(assh etrofitkitinto howninHow otheshallow tochangeth housing. hetorsionsp ringsinto n Figure 1 mp base into ng the torsio fit(asshown o the socket. on springs inHowtoch Connect the into friction hangethetor e lamp base n brackets if rsionsprings to LEDRetro f necessary intofriction fitkitbyconn before conn brackets). nector. nect the lam mp base andd Installatio STEP1:
Disconnect
*Tips: For t a) Remov shallow b) Change friction STEP2:
As shown in Twist the la
*Tips: Chan LED Retrof Figure1 STEP3:
Arrange the
(as shown i e ends of tors sion spring in n Figure 2). nside the lam mp holder bay yonetorput thefrictionb bracketsinto thehousing withtors sionspring Figure2 withfricti onbrackets s n Figure 3. EDRetrofitkit t into the hou using until its s outer edge is flush agai nst the ceilin ng surface. Figure3 he installation n and turn on the power s supply. mote to conne ect the down nlight (asshow wninUserG uide4keyre emotecontro ollerOperati on). STEP5:
As shown in Push the LE STEP6:
Compete th STEP7 Use the rem adjustsh allowhou usingsock ketbracke et
*Howto Step1:
Remove the e rotary knob b by rotating and then tak ke out the ad djustable soc ket bracket (
(as shown in Figure 5). Figure5 e the adjusta able socket b bracket by pre essing the so ocket clips (a as shown in Step2:
Remove the Figu re6 Figure 6). Step3:
Putthesock ketbackintot thehousing(
(as shown in n Figure 7). re7 Figu changeth he screws an the friction br hetorsion nd remove th rackets with nspringsin he torsion sp the screws (
ntofrictio rings (as sho
(as shown in onbracket ts e 8). own in Figure Figure 9).
*Howto Loosen th Then fix t Figure8 Fig gure9