FCC ID: 2AB2Q5F49E9 Outdoor contact sensor

User Guide Outdoor Contact Sensor Quick Start In-app Setup 1. Make sure your Ring Alarm is disarmed. 2. In the Ring app, open the menu. Tap Set Up a Device, then tap Security, tap Sensor, and find the Outdoor Contact Sensor. 3. Follow the in-app instructions to complete setup. Installation We suggest mounting the Outdoor Contact Sensor using more than one mounting method, if needed. Make sure the Sensor and the Magnet are lined up, and 1" apart or less. Mounting Tape (included) Use the included mounting tape, clean the area, then peel the backing and stick the Sensor. Press it to the surface and hold for 20 seconds to make sure the tape is securely attached. Screws and anchors (included) If mounting on a hard surface, use a 3/16"

(5mm) drill bit to drill holes for the anchors, then push them into place and screw in the brackets. If mounting on a softer surface like wood, simply screw in the brackets. 2 screws included: 3x21mm 2 anchors included: 5x25mm 4mm4mm4mm4mm7mm7mm Metal strap tie (not included) Feed the metal strap tie through the back of the sensor and magnet brackets. Make sure that you tighten the strap tie so it doesnt slide around or down the pole. If it does move around, consider also using screws to keep it in place. Slide the Sensor and Magnet onto the mounting brackets when youve finished mounting them. 1 in 2.54 cm max 0.5 in 1.27 cm For additional help, visit: ring.com/help Find online manuals at:

ring.com/alarm-manual For technical Z-Wave information, visit:

ring.com/z-wave 2021 Ring LLC or its affiliates. Ring and all related marks are trademarks of Ring LLC or its affiliates. xx-xxxxxx-xx

Important Product Information Renseignements Importants Relatifs au Produit ENGLISH SAFETY INFORMATION FAILURE TO FOLLOW THESE SAFETY INSTRUCTIONS COULD RESULT IN FIRE, ELECTRIC SHOCK, OR OTHER INJURY OR DAMAGE. WARNING: Your device should only be used in accordance with the specific instructions for use and intended purpose of the device. Using your device in any way other than its intended purpose could cause injury to yourself, others and/or damage to the device or property. WATCH FOR SMALL PARTS! Your device and accessories may present a choking hazard to small children. Keep them out of reach of small children. CAUTION: The device is not waterproof and as such should not be submerged in water, doing so could cause injury to yourself, others and/or damage to the device. CAUTION: To reduce the risk of falling, take extra caution when using a ladder or similar equipment to mount the product. BATTERY SAFETY This product contains alkaline batteries. This device requires batteries for use. Only use new 1.5V alkaline AA-sized batteries. Never mix old and new batteries. Keep all of the batteries out of the reach of children. Do not open, disassemble, puncture, cut, bend, shred or heat the batteries and do not allow metal objects to touch the battery terminals on the device as they can become hot and cause burns. Remove all batteries if they are worn out or before storing your Device for an extended period of time. Dispose of all batteries in accordance with applicable laws and regulations and do not dispose of batteries by throwing them into a fire. If any batteries begin to leak, take steps to prevent the fluid from coming into direct contact with skin or clothes as the fluid could be corrosive and may be toxic. Remove the batteries and clean the battery compartment in accordance with the battery manufacturers recommendations. CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of the used batteries according to the manu-

facturers instructions. Maintaining Your Ring Outdoor Contact Sensor Use only accessories supplied with your device, or specifically marketed for use with your device, to power your device. Product Specifications Device Name: Ring Outdoor Contact Sensor Model Number: 5F49E9 Electrical Rating: 2 AA Alkaline Batteries (1.5V) Temperature Rating: -4F to 120F (-20C to 49C) RECYCLING YOUR DEVICE PROPERLY In some areas, the disposal of certain electronic devices is regulated. Make sure you dispose of, or recycle, your device in accordance with your local laws and regulations. For information about recycling your device, go to amazon.com/devicesupport Terms of Service and Warranty By purchasing or using the product, you agree to the Terms of Service found at ring.com/terms For information on our warranty visit ring.com/legal FOR CONSUMERS IN THE USA Suppliers Declaration of Conformity Compliance Information Statement Unique Identifier: Ring Outdoor Contact Sensor Model Number: 5F49E9 FCC ID: 2AB2Q5F49E9 Responsible Party and Party issuing Suppliers Declaration of Conformity Ring LLC, 1523 26th St., Santa Monica, CA 90404 www.ring.com / legal@ring.com FCC Compliance Statement This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment gener-

ates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful inter-

ference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interfer-

ence to radio or television reception, which can be determined by turn-

ing the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Connect the equipment into an outlet on a circuit different from that Increase the separation between the equipment and receiver. to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Pursuant to Section 15.21 of the FCC rules, changes or modifications to a Product by the user that are not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. The device meets the FCC Radio Frequency Emission Guidelines. Information on the product is on file with the FCC and can be found by inputting such Products FCC ID (which can be found on the device) into the FCC ID Search form available at fcc.gov/oet/ea/fccid Information Regarding Exposure to Radio Frequency Energy The output power of the radio technology used in the Products is below the radio frequency exposure limits set by the FCC. Nevertheless, it is advised to use this product in such a manner that minimizes the potential for human contact during normal operation. This device should be installed and oper-

ated with at least 20 cm between the radiator and your body. FOR CONSUMERS IN CANADA Innovation, Science and Economic Development Canada (ISED) Compliance IC ID: 10256A-5F49E9 This device contains licence-exempt transmitter(s)/ receiver(s) that comply with Innovation, Science and Economic Development Cana-

das licence-exempt RSS(s). Operation is subject to the following two conditions:

1. This device may not cause interference. 2. This device must accept any interference, including interference that may cause undesired operation of the device. Information Regarding Exposure to Radio Frequency Energy This equipment complies with IC RSS-102 RF exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and your body. FRANAIS RENSEIGNEMENTS RELATIFS LA SCURIT LE NON-RESPECT DE CES CONSIGNES DE SCURIT POUR-

RAIT CAUSER UN INCENDIE, UNE DCHARGE LECTRIQUE, OU DAUTRES BLESSURES OU DOMMAGES. AVERTISSEMENT : Votre appareil ne doit tre utilis que conformment son usage prvu et aux instructions prcises relatives son usage. Lutilisation de votre appareil dune manire autre que celle prvue pourrait vous blesser, blesser dautres personnes ou endommager lappareil ou votre proprit. ATTENTION : Votre appareil nest pas tanche et ne doit donc pas tre immerg dans leau, car cela pourrait vous blesser, blesser dautres personnes ou endommager lappareil. ATTENTION : Afin de rduire les risques de chute, soyez particulire-

ment prudent lorsque vous utilisez une chelle ou tout quipement similaire pour linstallation du produit. SCURIT CONCERNANT LA BATTERIE Ce produit contient des piles alcalines. Cet appareil ncessite des piles pour fonctionner. Nutilisez que des piles alcalines AA neuves de 1,5 V. Ne mlangez jamais des piles uses et des piles neuves. Gardez toutes les piles hors de la porte des enfants. Ne pas ouvrir, dmonter, percer, couper, plier, dchiqueter ou chauffer les piles et ne pas laisser dobjets mtalliques toucher les bornes de la pile sur lappareil, car elles peuvent devenir chaudes et causer des brlures. Retirez toutes les piles si elles sont uses ou avant de ranger votre appareil pendant une priode prolonge. liminez toutes les piles conformment aux lois et rgle-

ments en vigueur et ne les jetez pas au feu. Si les piles commencent fuir, prenez les mesures ncessaires pour empcher le liquide dentrer en contact direct avec la peau ou les vtements, car il pourrait tre corrosif et toxique. Retirez les piles et nettoyez le compartiment des piles conformment aux recommandations du fabricant. AVERTISSEMENT : Risque dexplosion si les piles sont remplaces incorrectement. Remplacez-les uniquement par un modle identique ou quivalent recommand par le fabricant. Jetez les piles uses conformment aux instructions du fabricant. Entretien du Ring Outdoor Contact Sensor Utilisez uniquement les accessoires fournis avec votre appareil, ou spcifiquement commercialiss pour une utilisation avec votre appareil, pour alimenter votre appareil. FAITES ATTENTION AUX PETITES PICES! Lappareil et les accessoires peuvent prsenter un risque dtouffement pour les enfants en bas ge. Gardez-les hors de la porte des enfants en bas ge. CARACTRISTIQUES DU PRODUIT Nom de lappareil : Ring Outdoor Contact Sensor Numro de modle : 5F49E9 Caractristiques lectriques : 2 piles alcalines AA (1,5 V) Tempratures de fonctionnement : de -20 C 49 C (-4 F 120 F) RECYCLEZ VOTRE APPAREIL CORRECTEMENT Dans certaines rgions, llimination de certains appareils lectro-

niques est rglemente. Assurez-vous de jeter ou de recycler votre appareil conformment aux lois et rglements locaux. Pour obtenir des renseignements sur le recyclage de votre appareil, visitez la page amazon.com/devicesupport Conditions de service et de garantie En achetant ou en utilisant le produit, vous acceptez les conditions de service qui se trouvent ring.com/terms Pour obtenir des renseignements sur la garantie, visitez la page ring.com/legal POUR LES CONSOMMATEURS AU CANADA Conformit aux exigences dInnovation, Sciences et Dveloppement conomique Canada (ISDE) IC ID : 10256A5F49E9 Cet appareil contient des metteurs/rcepteurs exempts de licence qui sont conformes aux normes CNR dInnovation, Sciences et Dvel-

oppement conomique Canada. Son utilisation est soumise aux deux conditions ci-dessous. 1. Cet appareil ne doit pas causer dinterfrences. 2. Cet appareil doit accepter toute interfrence, y compris les inter frences pouvant causer un fonctionnement indsirable de lappareil. Renseignements concernant lexposition lnergie des frquences radio Cet quipement est conforme aux limites dexposition aux frquences radio stipules dans le document IC CNR-102 RF pour les environne-

ments non contrls. Cet quipement doit tre install et utilis une distance minimale de 20 centimtres entre le radiateur et votre corps. Ring LLC 1523 26th St. Santa Monica, CA 90404 USA 2021 Ring LLC or its affiliates.Ring and all related marks are trademarks of Ring LLC or its affiliates. For Z-Wave technical information, visit ring.com/z-wave. Pour des informations techniques sur Z-Wave, visitez ring.com/z-wave XX-XXXXXX-XX

Label & Label location:

slide back cover off the device. label printed on inside of device Model number : 5F49E9 FCC ID: 2AB2Q5F49E9 IC: 10256A-5F49E9

LEEDARSON LIGHTING CO., LTD. Date: 2021/6/21 Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 To whom it may concern:

I, the undersigned, hereby authorize UL Verification Services Inc. to act on our behalf in all manners relating to application for equipment authorization, including signing of all documents relating to these matters. Any and all acts carried out by UL Verification Services Inc. on our behalf shall have the same effect as acts of our own. I, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). In authorizing UL Verification Services Inc. as our representative, we still recognize that we are responsible to:

a) comply with the relevant provisions of the certification program;

b) c) d) e) f) make all necessary arrangements for the conduct of the evaluation, including provision for examining documentation and access to all areas, records (including internal audit reports) and personnel for the purposes of evaluation (e.g. testing, inspection, assessment, surveillance, reassessment) and resolution of complaints;

make claims regarding certification only in respect of the scope for which certification has been granted;

do not use our product certification in such a manner as to bring the Certification Division into disrepute and not make any statement regarding our product certification which the Certification Division may consider misleading or unauthorized;

upon suspension or cancellation of certification, discontinue use of all advertising matter that contains any reference thereto and return any certification documents as required by the Certification Division;

use certification only to indicate the products are certified as being in conformity with specified standards;

g) h) i) j) endeavor to ensure that no certificate or report nor any part thereof is used in a misleading manner;

ensure that any reference to our product certification in communication media such as documents, brochures or advertising, complies with the requirements of the Certification Division;

keep a record of all complaints made known to us relating to the products compliance with requirements of the relevant standard and to make these records available to the when requested;

take appropriate action with respect to such complaints and any deficiencies found in products or services that affect compliance with the requirements for certification;

k) document the actions taken. This authorization is valid until further written notice from the applicant. Sincerely Yours, Signed by:

Company Name: LEEDARSON LIGHTING CO., LTD. Contact Name: Vick Zhang Title of Person: safety engineer Address: Xingda Road, Xingtai Industrial Zone, Changtai County, Zhangzhou, Fujian, China

LEEDARSON LIGHTING CO., LTD. Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 Subject:

Request for Confidentiality FCC ID:

2AB2Q5F49E9 To Whom It May Concern:

Pursuant to the provisions of Sections 0.457 and 0.459 of the Commissions rules (47 CFR 0.457, 0.459), we are requesting the Commission to withhold the following attachments as confidential document from public disclosure indefinitely. Schematic Diagram Block Diagram Theory of Operation Above mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. In additional to above mentioned documents, pursuant to Public Notice DA 04-1705 of the Commissions policy, in order to comply with the marketing regulations in 47 CFR 2.803 and the importation rules in 47 CFR 2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices. We are requesting the commission to grant short-term confidentiality request on the following attachments until 180 days. External Photos Internal Photos Test Setup Photos User Manual It is our understanding that all measurement test reports, FCC ID label format and correspondent during certification review process cannot be granted as confidential documents and those information will be available for public review once the grant of equipment authorization is issued. Best Regards Company Name: LEEDARSON LIGHTING CO., LTD. Contact Name: Vick Zhang Title of Person: safety engineer Address: Xingda Road, Xingtai Industrial Zone, Changtai County, Zhangzhou, Fujian, China Date: 2021/9/24