We build your success in IoT. Content:
Water Leak Sensor ................................................................................................................................. 2 1. Product Introduction ................................................................................................................ 2 2. Product Profile ......................................................................................................................... 2 3. Specification ............................................................................................................................. 2 4. Features/Capabilities: .............................................................................................................. 4 5. Installation Notice .................................................................................................................... 4 6. Installation Guide .................................................................................................................... 5 7. Product usage ......................................................................................................................... 5 8. Note......................................................................................................................................... 6 Water Leak Sensor User Manual 1. Product Introduction Using the LEEDARSON Water Leak Sensor and the LEEDARSON Application for your mobile device, you can receive immediate alerts if a leak or flooding occurs in your home (such as in a basement, near a water heater, under an old pipe, or in a bathroom). Early alerts can help you prevent leaks from turning into flood situation, extensive property damage and excessive bills. 2. Product Profile1 Screw
(Remove screws and back cover to replace battery) Reset button Testing pin 2 Specification Model Name Power Supply Power Source Battery Life Communication Protocol Radio Frequency Wireless Range Operational Temperature Buzzer sound hole 8B-SS-ZF-H0 Battery 3V, AAA *2 5 years Zigbee 3.0 2.4GHz 100ft (40m)LOS 0 - 40 Operating Humidity Up to 85% non-condensing Mounting Standards Compliance Floor type FCC, CE RED OTA Yes 3 3. Features/Capabilities The LEEDARSON Water Leak Sensor is a Zigbee compatible sensor. The LEEDARSON Water Leak Sensor is powered by AAA battery with a 5-years battery life. The LEEDARSON Water Leak alarm can be sent to Zigbee network devices or to any compatible alarm system hub. The LEEDARSON Water Leak Sensor is designed to be a floor type sensor.. The LEEDARSON Water Leak Sensor has a built-in LED indicator and an acoustic alarm. The LEEDARSON Water Leak Sensor has a low battery alarm to Zigbee Gateway/Hub devices 4. Installation Notice 1. Install the detector in areas where there is a concern about possible water leaks, such as bathrooms, basements, water heaters, under clogged drains, under old pipes, or in other areas of your home that are prone to leaking. You can receive an instant alert. 2. Do not locate the detector in cabinets and other areas where the alarm sound cannot be heard. 3. Do not install in an area where it can come in contact with rain, oil smoke and steam from a kitchen range. 4. Do not install the detector in submersed water. 5. If a pool of water forms, moisture must contact both leads to trigger an alert. 4 6. Installation Guide 1. The sensor will be in pairing status when power turns on for the first time. This will cause an LED indicator light to flash once per second for 3 minutes. Use the LEEDARSON Application to search for this device. If sensor pairs successfully, the light will stop blinking and then stay on for about 10 seconds. 2. Install the detector where there is a concern for a potential water leak. 7. Product usage 1. Insert 2 pcs AAA battery to the battery space, and the water leak sensor will be ready for use. 2. How to reset a water leak sensor A. Press and hold the reset key on the bottom cover for about 3 seconds, then the LED
(signal light) will start blinking quickly. B. Release the reset key and the sensor will be reset to factory settings and the LED(signal light) blinks once per second to search for a new enabled Zigbee network. 3. How to pair a water leak sensor A. After the sensor reset to factory settings, the LED(signal light) blinks once per second and sensor starts searching an enabled Zigbee network. B. If sensor pairs successfully, it will stop blinking and the light will stay on for 10 seconds C. If no available networks were found within 3 minutes, the LED will stop blinking and turn off. Tip: When initially setting up the LEEDARSON Water Leak Sensor, it is recommended to perform the setup task within 15 feet (4.5 meters) of the Zigbee Hub. 5 4. Once the sensor detects a water leak, the LED Indicator flashes and the alarm beeps once per second. The alarm signal will be sent to the gateway once every 5 minutes. During the alarm status, the user can mute the buzzer by using the App. If the sensor still detects a water leak after 10 minutes, the detector will trigger the alarm again and another signal will be sent to the gateway and the user. The alarm will be canceled if the situation as below. Water leak is controlled/stopped User presses the mute status by using the app The button on the sensor itself is pressed Power is turned off Details about the alarm: there are four settings to select from in App. 0: Buzzer muted, LED off 1: Buzzer muted, LED flashes 2: Buzzer on, LED off 3: Buzzer on, LED flashes (Default setting) 6. When the battery voltage low, the detector will send a low battery signal to the gateway. 8. Notes 1. Replace the battery immediately when the low battery warning sounds to ensure the detector is working properly. 2. Do not store any items on the surface of detector, as this may affect the sensors. 3. Clean the surface with soft towel regularly. 4. In the unlikelihood of a product failure, do not attempt to repair. Please contact the local distributor. 6 Attention RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation. Caution: The user is cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. 7 Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. IC NOTICE TO CANADIAN USERS Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. This Class B digital apparatus complies with Canadian ICES003 (Cet appareil numrique de la Classe B conforme la norme NMB003 du Canada). Hereby, Corporation declares that this device is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU 8