USERS GUIDE PANMOD for FCC Project Charon Version: 1.0 Document:
USERS GUIDE PANMOD for FCC.doc Template:
Pluto.dot 18. Nov 2005 Leica Geosystems AG RJ-4139 List of contents 1 Description ............................................................................................................. 2 2 General PANMOD configuration............................................................................ 2 2.1 PANMOD Connector.............................................................................................. 2 2.2 UART - USB........................................................................................................... 2 2.3 HCI WakeUp Bluetooth .......................................................................................... 3 2.4 HCI Base Band activ / Stollmann-SPP DCD........................................................... 3 2.5 Antenna Type and Matching Network..................................................................... 3 2.6 LEDs ..................................................................................................................... 3 3 PANMOD V3 configuration .................................................................................... 4 3.1 Picture.................................................................................................................... 4 3.2 Component Placement........................................................................................... 4 4 FCC Compliance..................................................................................................... 5 4.1 Labeling Requirements for End Product................................................................. 5 4.2 RF-exposure Statement ......................................................................................... 5 18. Nov 2005 I:\GPS\Charon\Hardware\Bluetooth\PANMOD\General Doku\USERS GUIDE PANMOD for FCC.doc 1 / 5 USERS GUIDE PANMOD for FCC Description 1 Description The PANMOD is a Bluetooth Modul based on the Class 2, Panasonic Bluetooth prequallified Standard modul PAN1440. General PANMOD Features :
Single 3.3V +/-5% input voltage
-25C to +85C operating and -40C to +85C storage temperature range Various Software Interfaces are available : HCI, Stollmann AT, Zerial AT Based on Bluetooth V1.2 prequallified Class 2 PAN1440 Bluetooth modul Bluetooth ID : B01839 HW configurable RS232 or USB 2.0 Interface RS232 with UART level (3.3V) HW configurable for internel or externel (U.FL connector) antenna PI-Pad antenna matching network to adapt the internel antenna to different surroundings 10 pin FCC zero force connector 2 General PANMOD configuration 2.1 PANMOD Connector CON1 Pin 1 2 3 4 5 6 7 8 9 10 Signal CTS RXD USB+
TXD USB+
RTS RESET-
BBACTIV DCD GPIO15 Type Remark valid only in RS232 mode RS232 mode USB mode RS232 mode USB mode IN IN USB OUT USB OUT valid only in RS232 mode IN OUT OUT I/O low activ, tactiv > 5ms H : Baseband activity (HCI) DCD with Stollmann SPP TBD WAKEUPHOST OUT HCI : Wake up Host WAKEUPBT GPIO03 VCC GND IN I/O IN
HCI : Wake up Bluetooth in RS232 mode TBD 3.3V +/- 5%
Ground 2.2 UART - USB With HCI software the hardware interface can be configured for USB or RS232 mode. With non HCI Software only RS232 mode is possible. Part RS232 mode HCI mode Remark R2 R5 R7 R13 R14 R15 R16 bold : settings for PANMOD V3 USB mode USB mode RS232 mode connect RXD to CON1 Pin 2 connect TXD to CON1 Pin 3 connect USB+ to CON1 Pin 2 connect USB- to CON1 Pin 3 1k0O 1k5O open open open 0O 0O 0O 0O open open open open 1K0O 18. Nov 2005 2 / 5 USERS GUIDE PANMOD for FCC General PANMOD configuration 2.3 HCI WakeUp Bluetooth When in HCI mode and the deep sleep mode is enabled this signal can be used to wake up the Bluetooth from deep sleep mode before sending data to the UART interface. To have the ability to define both initial state R9 and R10 are given. 2.4 HCI Base Band activ / Stollmann-SPP DCD Part Stollmann SPP DCD open 0O R3 R11 bold : settings for PANMOD V3 HCI Remark 0O GPIO_4 to CON1 Pin 6 open GPIO_15 to CON1 Pin 6 2.5 Antenna Type and Matching Network Int. Antenna Ext. Antenna Remark To select internel or externel antenna use see table below. Part C3 C4 C5 0.5pF 10pF 1.5nH open open open open 2pF set Pi-Pad : value for Charon Pi-Pad : value for Charon Pi-Pad : value for Charon Internel antenna U.FL selector U.FL connector ANT1 set open open C6 U.FL bold : settings for PANMOD V3 2.6 LEDs LED1 shows when lighting the running state of the ARM7 processor. LED2 shows in HCI mode the state of the base band activity. 18. Nov 2005 3 / 5 USERS GUIDE PANMOD for FCC PANMOD V3 configuration 3 PANMOD V3 configuration HCI Software Interface RS232 HW Interface with TXD, RXD, RTS, CTS HCI Base Band activity om CON1 Pin 6 Internel antenna with matching network No LED`s are populatet 3.1 Picture Bottom 3.2 Component Placement Top Bottom 18. Nov 2005 Top 4 / 5 4 FCC Compliance This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. 4.1 Labeling Requirements for End Product The PANMOD is labled with its own FCC ID number RFD-PANMOD1. For the end product which contains the PANMOD V3 there must be a lable containing, at least the following information :
This device contains FCC ID: RFD-PANMOD1 The label must be affixed on an exterior surface of the end product such that it will be visible upon inspection in compliance with the modular approval guidelines developed by the FCC. In addition, the user manual for the end product must contain the following information:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. 4.2 RF-exposure Statement The antenna shown in this filing must not be co-located or operated in conjunction with any other antenna or transmitter. End users may not be provided with the module installation instructions. OEM integrators and end users must be provided with transmitter operating conditions for satisfying RF exposure compliance. For portable applications OEM integrators need no SAR evaluation. The max source-based time-
averaged output of 1.17 mW is below the low threshold of 24mW for d < 2.5 cm. 18. Nov 2005 I:\GPS\Charon\Hardware\Bluetooth\PANMOD\General Doku\USERS GUIDE PANMOD for FCC.doc 5 / 5