all | frequencies |
|
|
|
|
exhibits | applications |
---|---|---|---|---|---|---|---|
manual | photos | label |
app s | submitted / available | |||||||
---|---|---|---|---|---|---|---|---|
1 2 |
|
Users Manual | Users Manual | 3.48 MiB | June 02 2022 | |||
1 2 |
|
Internal Photos | Internal Photos | 1.95 MiB | June 02 2022 | |||
1 2 |
|
External Photos | External Photos | 1.03 MiB | June 02 2022 | |||
1 2 |
|
Label and Label Location | ID Label/Location Info | 290.71 KiB | June 02 2022 | |||
1 2 | Block Diagram | Block Diagram | June 02 2022 | confidential | ||||
1 2 |
|
Cover Letters | Cover Letter(s) | 23.87 KiB | June 02 2022 | |||
1 2 | Operational Description | Operational Description | June 02 2022 | confidential | ||||
1 2 |
|
Exposure info | RF Exposure Info | 2.06 MiB | June 02 2022 | |||
1 2 | Schematics | Schematics | June 02 2022 | confidential | ||||
1 2 |
|
Test Report | Test Report | 3.18 MiB | June 02 2022 | |||
1 2 |
|
Test Setup Photos | Test Setup Photos | 209.05 KiB | June 02 2022 |
1 2 | Users Manual | Users Manual | 3.48 MiB | June 02 2022 |
Leica Zeno FLX100 plus Smart Antenna User Manual Version 1.0 English Introduction Purchase Congratulations on the purchase of the Leica Zeno FLX100 plus smart antenna. This manual contains important safety directions as well as instructions for setting up the product and operating it. Refer to 1 Safety Directions for fur-
ther information. Read carefully through the User Manual before you switch on the product. The content of this document is subject to change without prior notice. Ensure that the product is used in accordance with the latest version of this docu-
ment. Product identification The model and serial number of your product are indicated on the type label. Always refer to this information when contacting your agency or Leica Geo-
systems authorised service centre. Trademarks Windows is a registered trademark of Microsoft Corporation in the United States and other countries Bluetooth is a registered trademark of Bluetooth SIG, Inc. Android is a trademark of Google Inc. Apple, iPad, iPad Air, iPad Pro, and iPhone are trademarks of Apple Inc., registered in the U.S. and other countries. Use of the Made for Apple badge means that an accessory has been designed to connect specifically to the Apple product(s) identified in the badge, and has been certified by the developer to meet Apple perform-
ance standards. Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards. iOS is a trademark or registered trademark of Cisco in the U.S. and other countries and is used under license. All other trademarks are the property of their respective owners. Validity of this manual Available documentation This manual applies to the Leica FLX100 plus smart antenna. Name Description/Format Provides an overview of the product together with technical data and safety directions. Intended as a quick reference guide. Quick Start Video QR code Leica FLX100 plus smart antenna Quick Guide 2 Name Description/Format Leica FLX100 plus smart antenna User Manual All instructions required in order to operate the product to a basic level are contained in the User Manual. Provides an overview of the product together with technical data and safety directions. Refer to the myWorld web page for all Leica FLX100 plus smart antenna documentation/software:
https://myworld.leica-geosystems.com https://myworld.leica-geosystems.com offers a wide range of services, inform-
ation and training material. With direct access to myWorld, you are able to access all relevant services whenever it is convenient for you. The availability of services depends on the instrument model. Service myProducts Description myService mySupport myLearning myTrustedServices mySmartNet Add all products that you and your company own and explore your world of Leica Geosystems: View detailed information on your products and update your products with the latest software and keep up-
to-date with the latest documentation. View the current service status and full service his-
tory of your products in Leica Geosystems service centres. Access detailed information on the services performed and download your latest calibration cer-
tificates and service reports. Create new support requests for your products that will be answered by your local Leica Geosystems Support Team. View the complete history of your support requests and view detailed information on each request in case you want to refer to previous support requests. Welcome to the home of Leica Geosystems online learning! There are numerous online courses avail-
able to all customers with products that have valid CCPs (Customer Care Packages). Add your subscriptions and manage users for Leica Geosystems Trusted Services, the secure software services, that assist you to optimise your workflow and increase your efficiency. Add and view your HxGN SmartNet subscriptions and user information. HxGN SmartNet delivers high-pre-
cision and high-availability GNSS network correction services in real time. The HxGN SmartNet Global family offers Network RTK with RTK bridging and Precise Point Positioning (PPP) services. These ser-
vices work exclusively with Leica Geosystems GS sensors, providing the highest accuracy. Combined, they ensure HxGN SmartNet coverage everywhere. 3 Service myDownloads Description Downloads of software, manuals, tools, training material and news for Leica Geosystems products. 4 1 2 3 4 5 6 Table of Contents Safety Directions 1.1 1.2 1.3 1.4 1.5 General Introduction Definition of Use Limits of Use Responsibilities Hazards of Use Description of the System 2.1 2.2 2.3 General Information Instrument Components Accessories Operation 3.1 3.2 3.3 3.4 3.5 3.6 Power On/Off, Reset, Charging Setups for the FLX100 plus Smart Antenna Phase Centre of the FLX100 plus Smart Antenna Setting of the FLX100 plus Smart Antenna Configure Real-time Corrections Firmware Upload Care and Transport 4.1 4.2 4.3 Transport Storage Cleaning and Drying Technical Data 5.1 5.2 5.3 Accessories Conformity to National Regulations Dangerous Goods Regulations Leica FLX100 plus Smart Antenna Bundle 6.1 6.2 6.3 Standard Configuration Accessories Packages for the FLX100 plus Smart Antenna 7 Software Licence Agreement/Warranty 6 6 7 7 7 8 13 13 14 15 16 16 16 18 18 19 20 21 21 21 22 23 24 24 26 28 28 28 29 31 Table of Contents 5 1 1.1 Description About warning messages Safety Directions General Introduction The following directions enable the person responsible for the product, and the person who actually uses the equipment, to anticipate and avoid opera-
tional hazards. The person responsible for the product must ensure that all users understand these directions and adhere to them. Warning messages are an essential part of the safety concept of the instru-
ment. They appear wherever hazards or hazardous situations can occur. Warning messages... make the user alert about direct and indirect hazards concerning the use of the product. contain general rules of behaviour. For the users safety, all safety instructions and safety messages shall be strictly observed and followed! Therefore, the manual must always be available to all persons performing any tasks described here. DANGER, WARNING, CAUTION and NOTICE are standardised signal words for identifying levels of hazards and risks related to personal injury and property damage. For your safety, it is important to read and fully understand the following table with the different signal words and their definitions! Supple-
mentary safety information symbols may be placed within a warning message as well as supplementary text. Type Description DANGER WARNING CAUTION NOTICE Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. Indicates a potentially hazardous situation or an unintended use which, if not avoided, could result in death or serious injury. Indicates a potentially hazardous situation or an unintended use which, if not avoided, may result in minor or moderate injury. Indicates a potentially hazardous situation or an unintended use which, if not avoided, may result in appreciable material, financial and environmental damage. Important paragraphs which must be adhered to in practice as they enable the product to be used in a technically correct and efficient manner. 6 Safety Directions 1.2 Intended use Definition of Use Reasonably foresee-
able misuse Carrying out measurement tasks using various GNSS measuring techniques Computing with software Data communication with external appliances Data transfer with Bluetooth Measuring coordinates Measuring raw data and computing coordinates using carrier phase and code signal from GNSS satellites (GNSS systems) Recording GNSS and point related data Recording measurements Use of the product without instruction Use outside of the intended use and limits Disabling of safety systems Removal of hazard notices Opening the product using tools, for example a screwdriver, unless this is permitted for certain functions Modification or conversion of the product Use after misappropriation Use of products with recognisable damage or defects Use with accessories from other manufacturers without the prior explicit approval of Leica Geosystems Inadequate safeguards at the working site 1.3 Environment Limits of Use Suitable for use in an atmosphere appropriate for permanent human habita-
tion. Not suitable for use in aggressive or explosive environments. WARNING Working in hazardous areas, or close to electrical installations or sim-
ilar situations Life Risk. Precautions:
Local safety authorities and safety experts must be contacted by the person responsible for the product before working in such conditions. 1.4 Responsibilities Manufacturer of the product Leica Geosystems AG, CH-9435 Heerbrugg, hereinafter referred to as Leica Geosystems, is responsible for supplying the product, including the User Manual and original accessories, in a safe condition. Safety Directions 7 Person responsible for the product The person responsible for the product has the following duties:
To understand the safety instructions on the product and the instructions in the User Manual To ensure that it is used in accordance with the instructions To be familiar with local regulations relating to safety and accident pre-
vention To stop operating the system and inform Leica Geosystems immediately if the product and the application become unsafe To ensure that the national laws, regulations and conditions for the oper-
ation of the product are respected 1.5 Hazards of Use DANGER Risk of being struck by lightning If the product is used with accessories, for example on masts, staffs, poles, you may increase the risk of being struck by lightning. Danger from high voltages also exists near power lines. Lightning, voltage peaks, or the touching of power lines can cause damage, injury and death. Precautions:
Do not use the product in a thunderstorm as you can increase the risk of being struck by lightning. Be sure to remain at a safe distance from electrical installations. Do not use the product directly under or close to power lines. If it is essential to work in such an environment contact the safety authorities responsible for electrical installations and follow their instructions. If the product has to be permanently mounted in an exposed location, it is advisable to provide a lightning conductor system. A suggestion on how to design a lightning conductor for the product is given below. Always follow the regulations in force in your country regarding grounding antennas and masts. These installations must be carried out by an authorised specialist. To prevent damages due to indirect lightning strikes (voltage spikes) cables, for example for antenna, power source or modem should be protected with appropriate protection elements, like a lightning arrester. These installations must be carried out by an authorised specialist. If there is a risk of a thunderstorm, or if the equipment is to remain unused and unattended for a long period, protect your product addition-
ally by unplugging all systems components and disconnecting all connect-
ing cables and supply cables, for example, instrument - antenna. 8 Safety Directions DANGER Risk of electrocution Because of the risk of electrocution, it is dangerous to use poles, levelling staffs and extensions in the vicinity of electrical installations such as power cables or electrical railways. Precautions:
Keep at a safe distance from electrical installations. If it is essential to work in this environment, first contact the safety authorities responsible for the electrical installations and follow their instructions. WARNING Improper disposal of product If the product is improperly disposed of, the following can happen:
If polymer parts are burnt, poisonous gases are produced which may impair health. If batteries are damaged or are heated strongly, they can explode and cause poisoning, burning, corrosion or environmental contamination. By disposing of the product irresponsibly you may enable unauthorised persons to use it in contravention of the regulations, exposing themselves and third parties to the risk of severe injury and rendering the environ-
ment liable to contamination. The product must not be disposed with household waste. Dispose of the product appropriately in accordance with the national regulations in force in your country. Always prevent access to the product by unauthorised personnel. Precautions:
WARNING Distraction or loss of attention During dynamic applications there is a danger of accidents occurring if the user does not pay attention to the environmental conditions around, for example obstacles, excavations or traffic. Precautions:
The person responsible for the product must make all users fully aware of the existing dangers. WARNING Lightning strike If the product is used with accessories, for example masts, staffs, poles, you may increase the risk of being struck by lightning. Precautions:
Do not use the product in a thunderstorm. Safety Directions 9 WARNING Inadequate securing of the working site This can lead to dangerous situations, for example in traffic, on building sites and at industrial installations. Precautions:
Always ensure that the working site is adequately secured. Adhere to the regulations governing safety, accident prevention and road traffic. WARNING Improperly repaired equipment Risk of injuries to users and equipment destruction due to lack of repair knowledge. Precautions:
Only authorised Leica Geosystems Service Centres are entitled to repair these products. For the AC/DC power supply:
WARNING Electric shock due to missing ground connection If unit is not connected to ground, death or serious injury can occur. Precautions:
The power cable and power outlet must be grounded!
For the AC/DC power supply and the battery charger:
WARNING Electric shock due to use under wet and severe conditions If unit becomes wet, it may cause you to receive an electric shock. Precautions:
If the product becomes humid, it must not be used!
Use the product only in dry environments, for example in buildings or vehicles. Protect the product against humidity. 10 Safety Directions For the AC/DC power supply and the battery charger:
WARNING Touching live components Using the product after incorrect attempts were made to carry out repairs. Unauthorised opening of the product Either of the following actions may cause you to receive an electric shock:
Precautions:
Do not open the product!
Only Leica Geosystems authorised service centres are entitled to repair these products. CAUTION Unapproved chargers or cables Connecting the charger improperly may cause serious damage to the device. Any damage caused by misuse is not covered by the warranty. Unapproved chargers or cables can cause the battery to explode or damage the device. Precautions:
Use only Leica-approved chargers, batteries, and cables. CAUTION Keeping the device too close to the human body during operation Health risk Precautions:
Use the device at least 10 mm apart from the human body. This device has been tested for typical operations near the human body, for example handheld mode, with the device kept at 10 mm from the users body. CAUTION Not properly secured accessories If the accessories used with the product are not properly secured and the product is subjected to mechanical shock, for example blows or falling, the product may be damaged or people can sustain injury. Precautions:
When setting up the product, make sure that the accessories are correctly adapted, fitted, secured, and locked in position. Avoid subjecting the product to mechanical stress. CAUTION Dropping the product When being dropped, the product can cause personal injury and/or mechanical damage. Precautions:
Ensure to have a firm grip on the product before operating it. Safety Directions 11 CAUTION CAUTION NOTICE Before any cleaning procedure, ensure that the instrument is switched off and the battery has been removed. Unused connectors must be protected using the attached dust cap. Rooting your Android device will void your right for any warranty services and support by Leica!
12 Safety Directions 2 2.1 Design Description of the System General Information The instrument Four satellite-system (BeiDou, GPS, GLONASS, Galileo), support access to external differential signal to get typical 2 cm (2D) positioning results FLX100 plus smart antenna with integrated helix antenna and Bluetooth capability Small and lightweight, wearable Low power consumption, long battery duration Rubber bumper for drop protection Is designed to be used on the pole or on the Universal Handheld Tray. It calculates a position from the computed ranges to all visible and activated GNSS satellites Can communicate with Leica Zeno GIS software:
Install Zeno Connect to use third-party applications Zeno Mobile, Zeno Connect: compatible with Android, iOS and Windows Description of the System 13 2.2 Description Instrument Components a b c d e f g Connection LED blue when Bluetooth connected GNSS correction indicator green when receiving correction data Satellite LED green when position available Battery LED indicator Green during normal operation Red when power < 10%
Red when charging Green when fully charged Power button to turn on/off the receiver Holes for the screws to fix the pole adapter USB-C port supports USB 2.0 14 Description of the System abcdg25020_001ef 2.3 Accessories Operation with pole Pole setup. Operation with smartphone Using the AZ220 Universal Handheld Tray for FLX100 plus smart antenna. Operation with tablet Using the AZ220/AZ225 Universal Handheld Tray for FLX100 plus smart antenna. a b c a b c a b c d Leica FLX100 plus smart antenna AZ219 Pole Mount GLS30 Carbon Pole Leica FLX100 plus smart antenna AZ220 Universal Handheld Tray Smartphone Leica FLX100 plus smart antenna AZ220/AZ225 Universal Hand-
held Tray Tablet AZ224 Handstrap tether for tablets Description of the System 15 a25023_001cb25024_001abc25025_001abcd 3 3.1 Description Operation Power On/Off, Reset, Charging Function Power on/off Description a b Power on/off button Battery LED indicator Turn on:
Press and hold the power button until all LEDs switch on. The device sounds a beep when ready for use. The device starts booting after the LEDs switch on. Once it is ready, the device sounds a beep. Turn off:
Press and hold the power button until all LEDs switch off and the device sounds a long beep. Use the standard charger and USB-C data cable to charge. The battery LED indicator is red while char-
ging and green when charging is finished. Charging 3.2 Setups for the FLX100 plus Smart Antenna Setup on a pole To attach the FLX100 plus smart antenna on the top of a pole, the pole mount adapter is required - Art. 915867. Follow these steps to connect the FLX100 plus smart antenna to the pole. 1. 2. Use a slot screwdriver to fix the pole mount adapter with both screws to the FLX100 plus smart antenna. Make sure to fix the pole mount adapter in the correct orientation. Screw the pole clockwise into the pole mount adapter. 16 Operation a25013_001b25014_00121 Setup with Universal Handheld Tray Use the Universal Handheld Tray to attach the FLX100 plus smart antenna with phone/tablet. The Universal Handheld Tray keeps the FLX100 plus smart antenna and phone/
tablet together. This setup maximises the productivity in the field. The Uni-
versal Handheld Tray has a spring-loaded frame to hold a phone/tablet of different sizes. Example:
Smartphone Example:
Tablet Operation 17 25027_00125028_001 3.3 Phase centre Phase Centre of the FLX100 plus Smart Antenna The phase centre of the FLX100 plus smart antenna location is at the dot near the top of the device. In pole mode, the offset from the phase centre to the top of the pole, includ-
ing the pole adapter mount, is automatically accounted. Make sure to provide the appropriate antenna height in the software. Pole mode Handheld mode In handheld mode, the location is measured at the dot. Make sure the FLX100 plus smart antenna is placed properly. Make sure that Pole or Handheld mode are set correctly in Zeno Mobile/Zeno Connect settings to change the phase centre posi-
tion. 3.4 Step-by-step Setting of the FLX100 plus Smart Antenna 1. Access the FLX100 plus smart antenna settings. a Phase centre position 2. 3. In Zeno Mobile 1. Go to Settings within a project. 2. Access GPS and then Antenna. In Zeno Connect 1. Open the app and go to Antenna. Tap on the three dots next to the FLX100 plus smart antenna. Configure the FLX100 plus smart antenna. The following settings are available:
Antenna Height (Only in Zeno Mobile) Antenna Usage Reset Antenna Info Refer to the according Zeno Mobile and Zeno Connect documenta-
tion for more information. 18 Operation 25029_001a 3.5 Step-by-step Configure Real-time Corrections This step-by-step procedure describes the configuration of the real-time cor-
rection in Zeno Mobile and Zeno Connect. RTK Profile Wizard 1. In Zeno Mobile In Zeno Connect 1. Go to Settings within a project. 2. Access GPS and then Realtime Cor-
rections. 1. Open the app and go to Settings. 2. Go to Realtime Corrections. Tap on + in the top-right corner of the screen to start the RTK profile wizard. Enter profile details. Provide a name and, optionally, a description for the new profile. Tap Next. Select profile type. Select Internet for real-time corrections streamed through the Internet. Select Radio or Beacon if using an external radio receiver. Only on Android. Tap Next. Create Data Server Tap Next. Select Mountpoint Tap on + to create a data server. Add the corresponding details and credentials for the data server that is providing the real-time corrections. Tap on the file icon to fetch the Mountpoint list from the server. An active Internet connection is required. Otherwise, manually insert the Mountpoint name. 2. 3. 4. 5. 6. 1. 2. 3. 1. 2. 3. Tap Next. Set the RTK Correction Detail. To do so, select the corresponding:
Data Format Network Type Reference Antenna 4. Tap Finish. Wizard end At the end of the wizard, the connection to the correction server is tested to verify the correct configuration. It is possible to save the profile independently of the connection test result. Operation 19 Further configuration Access again the Realtime Corrections menu to access the profiles. Modify any detail by tapping on the three dots next to the profile name. When position is available, activate/deactivate the automatic connection to the profile here. 3.6 Step-by-step Firmware Upload This step-by-step procedure describes how to upload the firmware on the FLX100 plus smart antenna. 1. 1. 2. 3. 4. 5. 6. 7. 8. Download Firmware The latest firmware is always available on myWorld. https://myworld.leica-geosystems.com Download the firmware ZIP file from the FLX100 Firmware option in the Software section of the antenna in myWorld. Send Firmware to FLX100 plus smart antenna by Bluetooth Unzip the file "update.bin" to your computer. Ensure the FLX100 plus smart antenna is turned on. Right-click "update.bin". Choose Send to > Bluetooth device. Select the corresponding serial number of the FLX100 plus smart antenna in the Bluetooth File Transfer window. Click Next. The firmware file is sent to the FLX100 plus smart antenna. It takes approximately 5 minutes. Click Finish in the Bluetooth File Transfer window once the transfer has completed. Alternatively, connect the FLX100 plus smart antenna to a PC/Laptop with the USBC cable. Copy the update.bin file from the update folder that can be found inside the FLX100 plus smart antenna memory. Update firmware one at a time. If both, System and GNSS, receive an update at the same time, perform one after the other sequentially. Install Firmware Now the firmware file has been transferred. 1. Once turned on again, the LEDs on the antenna flash one after the Turn the FLX100 plus smart antenna off and on again. other for a few seconds. When the firmware has successfully installed, the LEDs stop flashing and the antenna sounds a beep. 20 Operation 4 Care and Transport CAUTION Unapproved chargers or cables Connecting the charger improperly may cause serious damage to the device. Any damage caused by misuse is not covered by the warranty. Unapproved chargers or cables can cause the battery to explode or damage the device. Precautions:
Use only Leica-approved chargers, batteries, and cables. 4.1 Transport Transport in a road vehicle Never carry the product loose in a road vehicle, as it can be affected by shock and vibration. Always carry the product in its container and secure it. For products for which no container is available use the original packaging or its equivalent. Shipping When transporting the product by rail, air or sea, always use the complete original Leica Geosystems packaging, container and cardboard box, or its equi-
valent, to protect against shock and vibration. Shipping, transport of batteries When transporting or shipping batteries, the person responsible for the product must ensure that the applicable national and international rules and regulations are observed. Before transportation or shipping, contact your local passenger or freight transport company. 4.2 Product Battery care Li-Ion batteries Storage Respect the temperature limits when storing the equipment, particularly in summer if the equipment is inside a vehicle. Refer to 5 Technical Data for information about temperature limits. A rechargeable Li-Ion battery powers the instrument. The full performance of a new battery is achieved only after two or three complete charge and discharge cycles The battery can be charged and discharged hundreds of times. It eventu-
ally wears out Do not leave a fully charged battery connected to a charger, as overchar-
ging may shorten its life If left unused, a fully charged battery loses its charge over time Refer to Environmental specifications for information about storage tem-
perature range After storage recharge batteries before using Protect batteries from damp and wetness. Wet or damp batteries must be dried before storing or use A storage temperature range of 0 C to +30 C / +32 F to +86 F in a dry environment is recommended to minimize self-discharging of the battery At the recommended storage temperature range, batteries containing a 40% to 50% charge can be stored for up to one year. After this storage period the batteries must be recharged Care and Transport 21 4.3 Product and accessories Damp products Cleaning and Drying Use only a clean, soft, lint-free cloth for cleaning. If necessary, moisten the cloth with water or pure alcohol. Do not use other liquids; these may attack the polymer components. Dry the product, the container, the foam inserts and the accessories at a temperature not greater than 40 C/104 F and clean them. Do not repack until everything is dry. Always close the container when using in the field. Cables and plugs Keep plugs clean and dry. Blow away any dirt lodged in the plugs of the connecting cables. 22 Care and Transport 25030_001 5 Instrument Technical Data Type Satellites tracked Description GPS: L1C/A, L2C QZSS: L1C/A, L2C GLONASS: L1OF, L2OF BeiDou: B1I, B2I Galileo: E1B/C, E5b SBAS: WAAS, EGNOS, MSAS, GAGAN (L1 C/A) Channels Update rate Re-aquisition RTK initialisation Cold start time Hot start 184
< 2 s Up to 10 Hz Typically > 120 s Typically < 24 s Typically < 15 s Initialisation reliability Differential Data format
> 99.9%
RTCM3.3 NMEA Positioning Weight Connector Mounting System Accuracy and reliability are subject to satellite geometry (DOPs), multipath, refractions and obstructions. In static mode they are subject even to occupa-
tion times: the longer the Baseline, the longer the occupation time must be. Type RTK (RMS) Description Horizontal: typical 2 cm (2D) Dimensions L W H [mm]
139 80.6 31 Weight [g]
319 Universal Handheld Tray USB Pole Processor RAM Storage 1 USB-C connector, supports USB 2.0 Snap on handheld device and Leica FLX100 plus smart antenna Leica FLX100 plus smart antenna mounted on Pole Adapter/Pole ARM Cortex-A7 512 MB DDR3 8 GB total 2 GB for system, 6 GB for user Communication Bluetooth BT 5.0 Technical Data 23 Power Internal battery 3.8 V, 6120 mAh USB-C charging, supports 1.44 A fast charge Input voltage Power consumption Working time Charge time 5 V DC/2 A
< 1.5 W
> 20 hours Typically 4 hours Environmental specifications Type Operating temperature [C]
Storage temperature [C]
Instrument 40 to +65 40 to +80 External influences Protection Water, dust and sand IP67 Humidity Shock resistance Up to 100% (non-condensing) Designed to endure to a 2 m pole drop and 1.2 m free drop on concrete floor with no damage 5.1 Accessories Standard accessories USB cable, Arm/Belt pouch Optional accessories Carbon fiber pole, telescopic pole, bracket 5/8", soft bag Universal Handheld Tray 5.2 Conformity to National Regulations Labelling Leica FLX100 plus smart antenna Antennas Type Bluetooth Antenna Gain [dBi]
Internal Microstrip antenna 1.0 24 Technical Data 0025015_001Model: Zeno FLX100 plusSmart AntennaArt. No.: 958981Input:5V 2A DC Battery:3.85V 6120mAh /23.562WhLeica Geosystems AGCH-9435 HeerbruggMade in ChinaFCC ID: RFD-FLX100PLUSIC: 3177A-FLX100PLUSIP67Tongwell, Milton Keynes, MK15 8HTHexagon House, Michigan Drive,Importer: Leica Geosystems Ltd. GNSS frequency bands Type Frequency band [MHz]
FLX100 plus smart antenna GPS, QZSS, SBAS: L1 1575.42 GPS, QZSS: L2 1227.60 GLONASS: L1 1602.5625-1611.5 GLONASS: L2 1246.4375-1254.3 Galileo: E1 1575.42 Galileo: E5b 1207.14 BeiDou: B1 1561.098 BeiDou: B2 1207.14 Frequency bands, output power Type Frequency band
[MHz]
Output power1)
[dBm]
Bluetooth Bluetooth LE 24022480 24022480 5.90 1.5-9 Radiation Exposure Statement The radiated output power of the instrument is below the radio frequency exposure limits. Nevertheless, the instrument should be used in such a manner that the potential for human contact during normal operation is minimised. To avoid the possibility of exceeding the radio frequency exposure limits, keep a distance of at least 20 cm between you (or any other person in the vicinity) and the instrument. EU USA Hereby, Leica Geosystems AG declares that the radio equipment type FLX100 plus smart antenna is in compliance with Direct-
ive 2014/53/EU and other applicable European Directives. The full text of the EU declaration of conformity is avail-
able at the following Internet address: http://www.leica-geosys-
tems.com/ce. FCC ID: RFDFLX100PLUS FCC Part 15 This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, it may cause harmful interference to radio communications. However, there is no guarantee that interference does not occur in a particu-
lar installation. If this equipment does cause harmful interference to radio or television recep-
tion, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
1) Conducted power for mobile technologies and EIRP for other technologies. Technical Data 25 Canada CAN ICES-003 B/NMB-003 B IC: 3177AFLX100PLUS Reorient or relocate the receiving antenna. Increase the separation between the equipment and the receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Changes or modifications not expressly approved by Leica Geosystems for compliance could void the user's authority to operate the equipment. Canada Compliance Statement This device contains licence-exempt transmitter(s)/receiver(s) that com-
ply with Innovation, Science and Economic Development Canadas licence-
exempt RSS(s). Operation is subject to the following two conditions:
1. 2. This device may not cause interference This device must accept any interference, including interference that may cause undesired operation of the device Canada Dclaration de Conformit Lmetteur/rcepteur exempt de licence contenu dans le prsent appareil est conforme aux CNR dInnovation, Sciences et Dveloppement conomique Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes:
1. 2. Lappareil ne doit pas produire de brouillage Lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement Radio Frequency (RF) Exposure Compliance Statement The radiated RF output power of the instrument is below the Health Canadas Safety Code 6 exclusion limit for portable devices (radiated element separation distance between the radiating element and user and/or bystander is below 20 cm). Others The conformity for countries with other national regulations has to be approved prior to use and operation. 5.3 Dangerous Goods Regulations Dangerous Goods Regulations Many products of Leica Geosystems are powered by Lithium batteries. Lithium batteries can be dangerous under certain conditions and can pose a safety hazard. In certain conditions, Lithium batteries can overheat and ignite. When carrying or shipping your Leica product with Lithium batteries onboard a commercial aircraft, you must do so in accordance with the IATA Dangerous Goods Regulations. Leica Geosystems has developed Guidelines on How to carry Leica products and How to ship Leica products with Lithium batteries. Before any transportation of a Leica product, we ask you to consult these guidelines on our web page (IATA Lithium Batteries) to ensure that you are in accordance with the IATA Dangerous Goods Regula-
tions and that the Leica products can be transported correctly. 26 Technical Data Damaged or defective batteries are prohibited from being carried or transported onboard any aircraft. Therefore, ensure that the condi-
tion of any battery is safe for transportation. Technical Data 27 6 6.1 Leica FLX100 plus Smart Antenna Bundle Standard Configuration Description The following table shows all parts for the standard configuration. Description Leica FLX100 plus smart antenna Power adaptor with 4 plugs (US, UK, EU and AU) Cable USB-C/USB-C, 1.5 m Cable USB-C/USB-A, 1.5 m AZ222 Arm/Belt pouch Soft bag for Leica FLX100 plus smart antenna, black Cardboard box Qty. 1 1 1 1 1 1 1 6.2 Overview Accessories List of accesories available for the Leica FLX100 plus smart antenna:
Part number Description Pole Mount to attach the Leica FLX100 plus smart antenna with Pole AZ219 AZ220 AZ225 AZ221 AZ222 AZ224 Universal Handheld Tray Universal Handheld Tray > 8 Softbag Arm/Belt pouch Handstrap tether for tablets 28 Leica FLX100 plus Smart Antenna Bundle The Pole is an optional accessory for the Leica FLX100 plus smart antenna. To use the Leica FLX100 plus smart antenna on a Pole, the appropriate adapter is required. This mounting allows customers to use the instrument vertically for precise and stable support. The Universal Handheld Tray is an optional accessory for the Leica FLX100 plus smart antenna. 6.3 Overview Packages for the FLX100 plus Smart Antenna Description Part number, Package 6015968 FLX100 plus Handheld Start package with Zeno Mobile 6015969 FLX100 plus Handheld Start package for third party Leica Zeno FLX100 plus smart antenna including:
Multi-constellation support, GPS, GLONASS, Galileo and BeiDou Power adapter USB-C charging cable USB-C/USB-A cable Arm/Belt pouch arm bag Softbag Universal Handheld Tray Zeno Mobile Professional with 1-year software maintenance Leica Zeno FLX100 plus smart antenna including:
Multi-constellation support, GPS, GLONASS, Galileo and BeiDou Power adapter USB-C charging cable USB-C/USB-A cable Arm/Belt pouch arm bag Softbag Universal Handheld Tray Install Zeno Connect from the app stores in order to use third party software Leica FLX100 plus Smart Antenna Bundle 29 Description Part number, Package 6015970 FLX100 plus Pole Start package with Zeno Mobile 6015971 FLX100 plus Pole Start package for third party Leica Zeno FLX100 plus smart antenna including:
Multi-constellation support, GPS, GLONASS, Galileo and BeiDou Power adapter USB-C charging cable USB-C/USB-A cable Arm/Belt pouch arm bag Softbag Zeno Tab 2 Android tablet Pole Mount Kit for Zeno Tab 2 GLS30 GNSS telescopic carbon fibre pole 5/8 pole mount to attach a FLX100 plus smart antenna to a Leica GNSS pole Zeno Mobile Professional with 1-year software maintenance Leica Zeno FLX100 plus smart antenna including:
Multi-constellation support, GPS, GLONASS, Galileo and BeiDou Power adapter USB-C charging cable USB-C/USB-A cable Arm/Belt pouch arm bag Softbag Zeno Tab 2 Android tablet Pole Mount Kit for Zeno Tab 2 GLS30 GNSS telescopic carbon fiber pole 5/8 pole mount to attach a FLX100 plus smart antenna to a Leica GNSS pole Install Zeno Connect from the app stores in order to use third party software 30 Leica FLX100 plus Smart Antenna Bundle 7 Software Licence Agreement/Warranty International Limited Warranty This product is subject to the terms and conditions set out in the International Limited Warranty which you can download from the Leica Geosystems AG home page at Leica Warranty or collect from your Leica Geosystems AG dis-
tributor. Software Licence Agreement This product contains software that is preinstalled on the product, or that is supplied to you on a data carrier medium, or that can be downloaded by you online according to prior authorisation from Leica Geosystems. Such software is protected by copyright and other laws and its use is defined and regulated by the Leica Geosystems Software Licence Agreement, which covers aspects such as, but not limited to, Scope of the Licence, Warranty, Intellectual Property Rights, Limitation of Liability, Exclusion of other Assurances, Govern-
ing Law and Place of Jurisdiction. Please make sure, that at any time you fully comply with the terms and conditions of the Leica Geosystems Software Licence Agreement. Such agreement is provided together with all products and can also be referred to and downloaded at the Leica Geosystems home page at Hexagon Legal Documents or collected from your Leica Geosystems distrib-
utor. You must not install or use the software unless you have read and accepted the terms and conditions of the Leica Geosystems Software Licence Agree-
ment. Installation or use of the software or any part thereof, is deemed to be an acceptance of all the terms and conditions of such Licence Agreement. If you do not agree to all or some of the terms of such Licence Agreement, you must not download, install or use the software and you must return the unused software together with its accompanying documentation and the purchase receipt to the distributor from whom you purchased the product within ten (10) days of purchase to obtain a full refund of the purchase price. The software on the product may contain copyright-protected software that is licenced under various open source licences. Copies of the corresponding licences are provided together with the product (for example in the About panel of the software) can be downloaded on http://opensource.leica-geosystems.com If foreseen in the corresponding open source licence, you may obtain the corresponding source code and other related data on http://opensource.leica-geosystems.com. Contact opensource@leica-geosystems.com in case you need additional information. Open Source information Software Licence Agreement/Warranty 31 Original text (970060-1.0.0en) Published in Switzerland, 2022 Leica Geosystems AG 970060-1.0.0en Leica Geosystems AG Heinrich-Wild-Strasse 9435 Heerbrugg Switzerland www.leica-geosystems.com Specific Absorption Rate (SAR) information:
This Smart Phone meets the government's requirements for exposure to radio waves. The guide lines are based on standards that were developed by independent scientific organizations through periodic and thorough evaluation of scientific studies. The standards include a substantial safety margin designed to assure the safety of all persons regardless of age or health. FCC RF Exposure Information and Statement:
The SAR limit of USA (FCC) is 0.501W/kg averaged over one gram of tissue. Device types: Smart handheld terminal (FCC ID: RFD-FLX100PLUS, IC: 3177A-FLX100PLUS) has also been tested against this SAR limit. During product certification, the maximum SAR value reported according to this standard is less than 0.501W/kg when correctly worn on the body. This device was tested for typical body-worn operations with the back of the Smart Phone kept 0cm from the body. To maintain compliance with FCC RF exposure requirements, use accessories that maintain a 0cm separation distance between the user's body and the back of the Tablet PC. The use of belt clips, holsters and similar accessories should not contain metallic components in its assembly. The use of accessories that do not satisfy these requirements may not comply with FCC RF exposure requirements, and should be avoided. Avertissement en franais Information sur l'Absorbance spcifique (SAR):
Ce smartphone rpond aux exigences du Gouvernement en matire d'exposition aux ondes radio. Ces lignes directrices sont fondes sur des critres tablis par des organismes scientifiques indpendants au moyen d'valuations priodiques et approfondies de la recherche scientifique. Ces normes comportent une marge de scurit importante et visent assurer la scurit de toutes les personnes, quel que soit leur ge ou leur tat de sant. Informations et dclarations sur l'exposition aux radiofrquences:
La limite SAR pour les tats - Unis (IC) est de 0501w / kg en moyenne par gramme de tissu. Le type d'appareil: Smart handterminal (IC: 3177A - FLX100PLUS) a galement t test en fonction de cette limite SAR. La valeur SAR maximale dclare conformment la prsente norme est infrieure 0501w / kg si elle est correctement porte sur la carrosserie du vhicule pendant la certification du produit. Lappareil a t test pour un fonctionnement portable typique, le dos du smartphone tant 0 cm du corps. Pour maintenir la conformit aux exigences d'exposition aux radiofrquences de fac, utilisez des accessoires qui maintiennent un espacement de 0 cm entre le corps de l'utilisateur et l'arrire de la tablette. Lorsque vous utilisez des ceintures, des tuis et des accessoires similaires, les composants mtalliques ne doivent pas tre inclus dans leurs composants. L'utilisation d'accessoires qui ne satisfont pas ces exigences peut ne pas satisfaire aux exigences en matire d'exposition aux radiofrquences et doit tre vite.
1 2 | Label and Label Location | ID Label/Location Info | 290.71 KiB | June 02 2022 |
Label Size: 3.5x2.0cm FCC ID: RFD-FLX100PLUS IC: 3177A-FLX100PLUS Smart Antenna Model No.: Zeno FLX100 plus Label location
1 2 | Cover Letters | Cover Letter(s) | 23.87 KiB | June 02 2022 |
2022-05-20 Equipment Autorisation Division Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 FCC ID: RFD-FLX100PLUS Product Name: Smart Antenna Request for Confidentiality Pursuant to Sections 0.457 and 0.459 of the commissions rules, we hereby request that the following documents be held confidential:
Schematics Long-term confidential Block diagram Long-term confidential Operation description Long-term confidential These materials contain trade secrets and proprietary information and are not customarily released to the public. The public disclosure of this information might be harmful to the company and provide unjustified benefits to our competitors. Signature:
2022-05-20 Name Position Company Name Address Tel Fax Email Hannes Juen Director Global Quality Management Leica Geosystems AG Heinrich-Wild-Strasse, 9435 Heerbrugg, Switzerland 41717273098 41717273098 hannes.juen@leica-geosystems.com
frequency | equipment class | purpose | ||
---|---|---|---|---|
1 | 2022-06-02 | 2412 ~ 2462 | DTS - Digital Transmission System | Original Equipment |
2 | 2402 ~ 2480 | DSS - Part 15 Spread Spectrum Transmitter |
app s | Applicant Information | |||||
---|---|---|---|---|---|---|
1 2 | Effective |
2022-06-02
|
||||
1 2 | Applicant's complete, legal business name |
Leica Geosystems AG
|
||||
1 2 | FCC Registration Number (FRN) |
0009479130
|
||||
1 2 | Physical Address |
Heinrich-Wild-Strasse
|
||||
1 2 |
CH-9435
|
|||||
1 2 |
Heerbrugg, N/A
|
|||||
1 2 |
Switzerland
|
|||||
app s | TCB Information | |||||
1 2 | TCB Application Email Address |
j******@nemko.com
|
||||
1 2 | TCB Scope |
A4: UNII devices & low power transmitters using spread spectrum techniques
|
||||
app s | FCC ID | |||||
1 2 | Grantee Code |
RFD
|
||||
1 2 | Equipment Product Code |
FLX100PLUS
|
||||
app s | Person at the applicant's address to receive grant or for contact | |||||
1 2 | Name |
H**** J******
|
||||
1 2 | Title |
Director Global Quality Management
|
||||
1 2 | Telephone Number |
00417********
|
||||
1 2 | Fax Number |
00417********
|
||||
1 2 |
h******@leica-geosystems.com
|
|||||
app s | Technical Contact | |||||
n/a | ||||||
app s | Non Technical Contact | |||||
n/a | ||||||
app s | Confidentiality (long or short term) | |||||
1 2 | Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | Yes | ||||
1 2 | Long-Term Confidentiality Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | No | ||||
if no date is supplied, the release date will be set to 45 calendar days past the date of grant. | ||||||
app s | Cognitive Radio & Software Defined Radio, Class, etc | |||||
1 2 | Is this application for software defined/cognitive radio authorization? | No | ||||
1 2 | Equipment Class | DTS - Digital Transmission System | ||||
1 2 | DSS - Part 15 Spread Spectrum Transmitter | |||||
1 2 | Description of product as it is marketed: (NOTE: This text will appear below the equipment class on the grant) | Smart Antenna | ||||
1 2 | Related OET KnowledgeDataBase Inquiry: Is there a KDB inquiry associated with this application? | No | ||||
1 2 | Modular Equipment Type | Does not apply | ||||
1 2 | Purpose / Application is for | Original Equipment | ||||
1 2 | Composite Equipment: Is the equipment in this application a composite device subject to an additional equipment authorization? | Yes | ||||
1 2 | Related Equipment: Is the equipment in this application part of a system that operates with, or is marketed with, another device that requires an equipment authorization? | No | ||||
1 2 | Grant Comments | Output power is conducted. End-users and installers must be provided with antenna installation and transmitter operating conditions for satisfying RF exposure compliance. The highest reported stand-alone body SAR values is 0.501 W/kg. | ||||
1 2 | Is there an equipment authorization waiver associated with this application? | No | ||||
1 2 | If there is an equipment authorization waiver associated with this application, has the associated waiver been approved and all information uploaded? | No | ||||
app s | Test Firm Name and Contact Information | |||||
1 2 | Firm Name |
Shenzhen Alpha Product Testing Co., LTD.
|
||||
1 2 | Name |
S****** G********
|
||||
1 2 | Telephone Number |
+86 7********
|
||||
1 2 |
s******@a-lab.cn
|
|||||
Equipment Specifications | |||||||||||||||||||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
1 | 1 | 15C | 2402 | 2480 | 0.001112 | ||||||||||||||||||||||||||||||||||||
1 | 2 | 15C | 2412 | 2462 | 0.019543 | ||||||||||||||||||||||||||||||||||||
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
2 | 1 | 15C | 2402.00000000 | 2480.00000000 | 0.0003980 |
some individual PII (Personally Identifiable Information) available on the public forms may be redacted, original source may include additional details
This product uses the FCC Data API but is not endorsed or certified by the FCC