FCC ID: 2A267-LBAVI7-CV Video Intercom System with 7 inch screen

DRAFT CONFIDENTIAL In order to make sure that LittleBird technology offers a valuable experience for all customers and users, all hardware associated with LittleBird features must be installed carefully and accurately. This document outlines the installation steps required to properly install a LittleBird Video Intercom system. The following steps should be precisely followed by a qualied technician to ensure system functionality and user safety. All local and national electric codes should be followed as these steps are completed. For additional product information, please visit partner-support.golittlebird.com This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modications not expressly approved by the manufacturer could void the users authority to operate the equipment Note:

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. This product has been found to be compliant to the requirements set forth in CFR 47 Section 1.1307 addressing RF Exposure from radio frequency devices, as dened in Evaluating Compliance with FCC Guidelines for Human Exposure to Radio Frequency Electromagnetic Fields. This device must be installed and operated so as to maintain a minimum separation distance to any person of 20 cm (8.7 inches). Before you begin Each video intercom system requires the following wiring:

16/2 or 18/2 for power. Use the table below for recommended maximum distances for the power wires. Wire Gauge Max Distance 14 16 18 275 ft 175 ft 100 ft 22/6 Shielded for Wiegand or relays. The maximum recommended distance is 300ft. The system includes two Form C relays, rated for 4A at 30V each. One CAT 5e or CAT 6 for wired ethernet Earth Ground for surge damage protection 16 AWG stranded wire or thicker and the length of wire should not Wire must be connected from the bottom left corner of the main motherboard inside the Video Intercom to a ground rod or cold water pipe. exceed 50 feet.

<diagram 1>

Whats included Each of your Video Intercom installation packages will include the following essential tools:

Quantity Item 1 4 4 1 1 2 1 Mounting template Concrete Anchors Lag Bolts x 2 MGT-2450 AC Transformer Microber Cloth (Yellow) Security Key Quick Start Guide What youll need Proper installation of your Video Intercom unit requires the following tools. Be sure to have them available before you begin the installation process. Electric drill/ Hammer drill *

7/16 inch socket w/ ratchet 5/32 drill bit for wood *

Philips screw driver concrete bit *

Level Pencil

* The use of this item depends on the mounting surface youre working with. Installation Instructions We recommend that you have an additional member of your team assist you during this installation process. Note: When locking and unlocking the Video Intercom unit, press the faceplate inward to compress the seal and then turn the lock. This will alleviate any pressure on the lock and allow the lock to spin with less resistance. 1. Using the included mounting template, mark the video intercoms four mounting holes on your installation areas surface following ADA guidelines. For the LBA-VI-12T model, the bottom two mounting holes should be <inches>

from the oor. For the LBA-VI-10 and LBA-VI-7 models, the bottom two mounting holes should be <inches> from the oor.

<diagram 2> <diagram 3>

2. Drill the four marked mounting holes.

<diagram 4>

Installation Material Bit size Wood Concrete, block, or masonry 15/64 3/8"

3. Insert the provided wall anchors 4. Install the top two lag bolts, but dont tighten them all the way, leaving about a 1/2" gap 5. Feed the power, Wiegand, and ethernet wires through the center hole in the back of the intercom

<diagram 6>

6. Use the top two keyed holes of the video intercom to mount the unit

<diagram 7>

7. Now tighten the top two lag bolts

<diagram 8>

8. Install the remaining two lag bolts

<diagram 9>

<diagram 10>

<diagram 11>

<diagram 12>

9. Plug in the ethernet wire into the ethernet jack on the board 10. Plug in the Wiegand or relay wires into the removable terminals on the board 11. Insert the two power wires into the AC terminals on the power supply 12. At the head end, attach the two power wires to the transformer, using the provided fork terminal connectors 13. Plug in the transformer to power up the video intercom unit 14. Wait for the video intercom system to boot up. You should see a screen similar to the one below when its done booting

<diagram 13>

<diagram 14>

<diagram 15>

15. Complete the units setup with LittleBird Support. To set up this nal check, call or email LittleBird Support at (602)607-4620 or service@golittlebird.com. Please include the site name, Video Intercom serial number, and contact information in the email or voicemail. Note: If you choose to call and a LittleBird technician isnt immediately available, youll receive a callback within 8 business hours 16. When the setup is complete, close and lock the lid with the provided keys Cleaning the Video Intercom Dust and moisture buildup may necessitate an occasional cleaning of the unit to keep the screen clear and the unit looking nice. Simply use water and the provided microber cloth to clean the screen, metal, and plastic.

<diagram 16>

vice complies with part 15 of the FCC Rules. tion is subject to the following two conditions:

This device may not cause harmful interference, 2) this device must accept any interference sived, including interference that may cause red operation

9/10/2021 Federal Communications Commission Authorization & Evaluation Division 7345 Oakland Mills Road Columbia, Maryland 21046 RE: LETTER OF AGENT AUTHORIZATION To Whom It May Concern:

We, the undersigned, hereby authorize Compliance Testing, LLC to act on our behalf in all matters relating to application for equipment authorization, including the signing of all documents relating to these matters. We also hereby certify that no party to the application authorized hereunder is subject to the denial of . benefits, including FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C.853(a). Sincerely, op pot Joseph Butler Sr. Product Engineer Level Up System Co., Inc.

9/10/2021 Communications Federal

& Evaluation Authorization Mills Road 7345 Oakland Maryland Columbia, Commission Division 21046 RE: Long-Term LBAVl7-CV Confidentiality Request for Model LBA-Vl-7-CELL-V AND FCC ID# 2A267-

To Whom It May Concern:

This letter 47.We have requested application serves as an official that the be permanently withheld request following documents from public review. for confidentiality under 0.457(d) required to be submitted and 0.459 of CFR with this Block Diagrams Schematics Theory of Operation Parts List/BOM contain which manufacturer/applicant system and equipment descriptions and a and related to be proprietary, detailed confidential, information These documents about the product, custom design and otherwise, basis from which future information these documents would be of benefit technological would not release products to its competitors, will evolve, considers to the general would give our competitors an unfair advantage in the market. public. Since this design is a manufacturer/applicant feels that this and that the disclosure of the information in Please contact me if there is any information you may need. Sincerely, Joseph Butler Sr. Product Level Up System Co., Inc. Engineer