FCC ID: 2ASLN-ZBMG2 Zigbee BLE Module C0945

Zigbee BLE Module C0945 Antenna Guidelines 1. Module Dimensions The module is of fixed dimensions and no outside changes are permitted. Refer to B9604module.dxf for footprint. 2 Leviton Confidential 2. Module Connections Recommended Module land Pattern Recommended to place the module along the PCB edge. Keep area under the antenna clear of any copper. Do not put any via under the module as they may cause problems. Do not route traces on PCB layer directly under the module. 3 Leviton Confidential 3. Module Placement Recommended Module placement on host board 4 Leviton Confidential 4. Antenna The module comes with a chip antenna design that followed the specifications of the antenna. About the signal line between PCB and an antenna on the module It is a 50-ohm line design. Fine tuning of return loss etc. can be performed using a matching network. However, it is required to check

"Class1 change" and "Class2 change" which the authorities define then. The concrete contents of a check are the following two points. 1. An antenna gain is lower than a gain given in antenna specifications. 2. The emission level is not getting worse. 5 Leviton Confidential 4. Antenna Please refer KDB 996369 D04 Module Integration Guide for guidance, installation instructions and testing requirements. 6 Leviton Confidential 4. Antenna Antenna trace path is as shown below. 7 Leviton Confidential 4. Antenna Antenna locations are as shown below. 8 Leviton Confidential 5. Bill of Materials Tuning Value Tuning # 1 Internal Antenna REF DES RF1 RF2 RF3 RF4 X2 IND, 5.6nH, SMD, 0402 CAP, 0.4pF, SMD, 0402 CAP, 0.5pF, SMD, 0402 RES, 0R, SMD, 0402 Chip Antenna 9 Leviton Confidential 6. Warning The module comes with a chip antenna design that followed the specifications of the antenna. The module has fixed antenna tuning values. Module is intended for Levitons use only. Any party involved should follow provided guidelines for layout of the module. Third party or outside customer is not allowed to change the antenna tuning values unless consulted and approved by the module manufacturer. Necessary filing and testing to be done by third party or outside customer in that case to prove regulatory compliance. 10 Leviton Confidential

Zigbee/ BLE Module C0945 Module Installation Manual FCC ID of this product is as follows:

FCC ID: 2ASLN-ZBMG2 IC ID of this product is as follows:

IC: 25037-ZBMG2 This module can be used for Bluetooth & ZigBee protocol. The module is tested in compliance with FCC part 15.247. It operates only in 2.4 GHz band

[2400-2483.5 MHz] and only ONE protocol at a time. For integration on Levitons end-product only module cannot be sold to general public. Therefore we will ask end-product documentation to include the following statements required by FCC and Industry Canada (IC) on the product and in the Installation Manual Notice. 1 Leviton Confidential Contents 1. Supply Voltage 2. Theory of operation 3. Module Dimensions 4. Module Footprint 5. Module Placement 6. Antenna 7. Notice 8. End-product testing 2 Leviton Confidential 1. Supply Voltage The power is provided from the 5-pin connector to the module. Rest pins on the connectors are for control signals. Min. Typ. Max. Unit Operating Temperature Range

-40

+25

+85 Deg. C Operating Voltage 3.0 3.3 3.6 VDC 3 Leviton Confidential 2. Theory of Operation BLE Channels Internal Antenna BLUETOOTH Frequency

(MHz) 2402 2404 2406 2408 2410 2412 2414 2416 2418 2420 2422 2424 2426 2428 2430 2432 2434 2436 2438 2440 TX Power -

Target MAX dBm (Dec/10)

[Avg Power FW Setting]

19 19 19 19 19 19 19 19 19 19 19 19 19 19 19 19 19 19 19 19 Channel #

18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 39 Channel #

37 0 1 2 3 4 5 6 7 8 9 10 38 11 12 13 14 15 16 17 Frequency Tolerance: 20ppm Frequency

(MHz) 2442 2444 2446 2448 2450 2452 2454 2456 2458 2460 2462 2464 2466 2468 2470 2472 2474 2476 2478 2480 TX Power -

Target MAX dBm (Dec/10)

[Avg Power FW Setting]

19 19 19 19 19 19 19 19 19 19 19 19 19 19 19 19 19 19 19 19 4 Leviton Confidential 2. Theory of Operation ZigBee Channels Internal Antenna ZigBee Channel #

Frequency

(MHz) 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 2405 2410 2415 2420 2425 2430 2435 2440 2445 2450 2455 2460 2465 2470 2475 2480 TX Power -

Target MAX dBm (Dec/10)

[Avg Power FW Setting]

19 19 19 19 19 19 19 19 19 19 19 19 19 19 19 17 Frequency Tolerance: 20ppm 5 Leviton Confidential 3. Module Dimensions The module is of fixed dimensions and no outside changes are permitted. Refer to C0945module.dxf for footprint. 6 Leviton Confidential 2. Module Connections Module can only be assembled on host PCB using the castellated connector. Keep area under the antenna clear of any copper or electrolytic components. 7 Leviton Confidential 4. Antenna The module comes with a chip antenna design that followed the specifications of the antenna. About the signal line between PCB antenna on the module It is a 50-ohm line design. Fine tuning of return loss etc. can be performed using a matching network. However, it is required to check "Class1 change" and "Class2 change" which the authorities define then. The concrete contents of a check are the following two points. 1. An antenna gain is lower than a gain given in antenna specifications. 2. The emission level is not getting worse. 8 Leviton Confidential 4. Antenna Please refer KDB 996369 D04 Module Integration Guide for guidance, installation instructions and testing requirements. 9 Leviton Confidential 7. Notice For Levitons end-product integration only device cannot be sold to general public. This module can be used either for Bluetooth & ZigBee protocol. The module is tested in compliance with FCC part 15.247. It operates only in 2.4 GHz band [2400-2483.5 MHz]. Therefore we will include the following statements required by FCC/ IC on the product and in the Installation Manual Notice. Please describe the following warning on the final product which contains this module. Contains Transmitter Module: FCC ID: 2ASLN-ZBMG2 IC: 25037-ZBMG2 OR Contains: FCC ID: 2ASLN-ZBMG2 IC: 25037-ZBMG2 Contient un module transmetteur: FCC ID: 2ASLN-ZBMG2 OR Contient: FCC ID: 2ASLN-ZBMG2 IC: 25037-ZBMG2 IC: 25037-ZBMG2 To comply with FCC and Industry Canada RF exposure limits for general population / uncontrolled exposure, the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and operating in conjunction with any other antenna or transmitter, except in accordance with FCC multi-transmitter product procedures. Pour se conformer aux limites d'exposition aux RF de la FCC et d'Industrie Canada pour la population gnrale / exposition non contrle, l'antenne(s) utilise pour ce transmetteur doit tre install pour fournir une distance de sparation d'au moins 20 cm de toutes les personnes et fonctionnant conjointement avec une autre antenne ou metteur, sauf en conformit avec les procdures de produits multi- metteur FCC. 10 Leviton Confidential 7. Notice Please describe the following warning to the manual. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Le produit dcrit aux prsentes est conforme aux exigences de la partie 15 des rglements de la FCC. Son utilisation est soumise aux deux conditions suivantes: (1) il ne cause aucun brouillage prjudiciable et (2) il nest pas affect par les interfrences dautres dispositifs susceptibles notamment den perturber le fonctionnement. This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canadas licence-exempt RSS(s). Operation is subject to the following two conditions:

1. This device may not cause interference. 2. This device must accept any interference, including interference that may cause undesired operation of the device. Lmetteur/rcepteur exempt de licence contenu dans le prsent appareil est conforme aux CNR dInnovation, Sciences et Dveloppement conomique Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes :

1. Lappareil ne doit pas produire de brouillage;

2. Lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. FCC/ ISED CAUTION Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. MISE EN GARDE DE LA FCC / ISED Toute modification apporte sans lautorisation expresse du responsable de la conformit pourrait avoir pour effet dannuler les droits dutilisation du produit dcrit aux prsentes. This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter. Le produit dcrit aux prsentes ne doit tre ni install ni utilis prs dautres antennes ou transmetteurs. 11 Leviton Confidential 7. Notice This device is intended only for Leviton end-product integrators under the following conditions:

1)The antenna must be installed such that 20 cm is maintained between the antenna and users, and 2)The transmitter module may not be co-located with any other transmitter or antenna. 3)The use of an antenna with gain less than 1.5 dBi (2.4GHz). Le produit dcrit aux prsentes ne peut tre utilis que par des produits finis Leviton dans les conditions suivantes:

1) son antenne doit tre installe de manire assurer un cart de 20 cmentre elle et les utilisateurs;

2) 3) son antenne doit avoir un gain de moins de 1.5 dBi (2.4 GHz). il ne doit tre ni install ni utilis prs dun autre transmetteur ou dune autre antenne;

As long as these 3 conditions above are met, further transmitter test will not be required. However, the integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed. IMPORTANT NOTE: In the event these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the FCC/ ISED authorization is no longer considered valid and the FCC/ ISED ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end-product (including the transmitter) and obtaining a separate FCC/ ISED authorization. REMARQUE IMPORTANTE: advenant quune ou plusieurs de ces conditions ne soient pas remplies (certaines configurations dordinateurs portables ou voisinage avec un autre transmetteur, p. ex.), lautorisation de la FCC/ISED ne serait plus juge comme tant valide et son identificateur ne pourrait plus tre utilis sur le produit. Dans de telles circonstances, le fabricant dquipement dorigine devra rvaluer le produit final (y compris son transmetteur) et obtenir une autre autorisation de la FCC/ISED. 12 Leviton Confidential 7. Notice End-Product Labeling This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm may be maintained between the antenna and users. The final end-product must be labeled in a visible area with the following:

Contains FCC ID:2ASLN-ZBMG2. Contains IC: 25037-ZBMG2. The grantee's FCC ID can be used only when all FCC compliance requirements are met. tiquetage du produit fini: le module transmetteur du produit dcrit aux prsentes ne peut tre utilis que dans des dispositifs dont lantenne permet un espacement de 20 cm entre elle et les utilisateurs. Le produit fini doit porter une tiquette visible portant les renseignements suivants:

Contient FCC ID:2ASLN-ZBMG2. Contient IC: 25037-ZBMG2. Lidentificateur de la FCC du dtenteur ne peut tre utilis que si toutes les exigences de conformit de lorganisme ont t respectes. Manual Information To the End User: The Levitons end-product integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the users manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual. Renseignements fournis aux utilisateurs: le fabricant dquipement dorigine doit savoir quil ne faut pas fournir aux utilisateurs des renseignements concernant linstallation ou le retrait du module RF dans le manuel dutilisation du produit qui le contient. Ce manuel doit toutefois comprendre toute linformation et tous les avertissements rglementaires requis. 13 Leviton Confidential 7. Notice Declaration of Conformity statement must be declared in the end-product user manual. FCC SUPPLIERS DECLARATION OF CONFORMITY Smart Sensors manufactured by Leviton Manufacturing, Inc., 201 N Service Road, Melville, NY, http://www.Leviton.com. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. DCLARATION DE CONFORMIT DU FABRICANT AUX EXIGENCES DE LA FCC Ce dtecteur intelligent est fabriqu par Leviton Manufacturing, Inc., 201 N Service Road, Melville, NY, http://www.leviton.com. Il est conforme aux exigences de la partie 15 des rglements de la FCC. Il peut tre utilis condition quil (1) ne cause aucun brouillage prjudiciable et (2) ne soit pas affect par les interfrences dautres dispositifs susceptibles notamment den perturber le fonctionnement. 14 Leviton Confidential 8. End-product testing During design process, Designer of the host board should place the module at recommended location on the host board. Designer should also perform the radiated regulatory FCC testing using manufacturers low-level radio test firmware to ensure compliance as per KDB 996369 D04. Designer should also test for the applicable unintentional radiator functions (Part 15 Subpart B) of the end-product to ensure compliance as per KDB 996369 D04. During production, Host products should be tested to ensure compliance. When the host board is manufactured, the requirement of Electrical Testing should be specified with the PCB order to guarantee that no short is present anywhere on the host board (which includes the traces to module RF castellation pads). This simplifies the production test requirements down to verifying that a solder short did not occur during the component placement and reflow of the host board assembly. Verifying no solder short has occurred can be done by measuring an open circuit between pins using a DC multi-meter. 15 Leviton Confidential

TechnicalDataSheet BRADYB747LASERTABMARKERS TDSNo.B747 EffectiveDate:02/21/2000 Description:

B747isapolyesterfilmwithanacrylicpressuresensitiveadhesiveandaprintablecoatingspeciallyformulatedforlaser printerandtoners.B747isavailableinwhiteoryellow. B747isrecommendedforalphanumericandbarcodeapplicationsthatrequiregoodsolventresistanceandmoderatetohigh temperatureperformance.ThisproductworkswellonthetopsideofmostcircuitboardsandIC's,aswellasgenerallabeling applications. B747isformulatedspeciallyforlaserprinters.Thematerialoffershighprintresolution,goodsolventresistance,smudge resistanceandmoderatetohightemperatureperformance. B747whiteisaULrecognizedcomponentandCSAacceptedmaterialwhenprintedwithdesignatedlaserprinters.SeeUL fileMH17154andCSAAcceptanceRecordLS41833forspecificdetails. PHYSICALPROPERTIES TESTMETHODS Details:

Thickness Adhesionto:

StainlessSteel TexturedABS Tack DropShear TensileStrengthandElongation DielectricStrength ASTMD1000 Substrate Adhesive Total ASTMD1000 20minutedwell 24hourdwell 20minutedwell 24hourdwell ASTMD2979 PolykenProbeTack

(1seconddwell,1cm/secseparation) PSTC7(exceptuse1/2"x1"sample) ASTMD1000 MachineDirection CrossDirection ASTMD1000 AVERAGERESULTS 0.0026inch(0.0660mm) 0.0011inch(0.0279mm) 0.0037inch(0.0940mm) 46oz/inch(50N/100mm) 56oz/inch(61N/100mm) 9oz/inch(10N/100mm) 16oz/inch(18N/100mm) 17oz(503g) 22hours 39lbs/inch(683N/100mm),77%

53lbs/inch(928N/100mm),65%

7000volts PerformancePropertiestestedonB747sampleslaserprintedwithHewlettPackardLaserjetIII. PERFORMANCEPROPERTIES TESTMETHODS TYPICALRESULTS HighServiceTemperature LowServiceTemperature HumidityResistance UVLightResistance Weatherability 30daysat267F(130C) 30daysat40F(40C) 30daysat100F(37C),95%R.H. 30daysinUVSunlighter100 ASTMG155,Cycle1 30daysinXenonArcWeatherometer Novisibleeffect Novisibleeffect Novisibleeffect Novisibleeffect Novisibleeffect PERFORMANCEPROPERTY CHEMICALRESISTANCE SamplesprintedwithaHewlettPackardLaserjetIIIprinter.Testwasconductedatroomtemperatureafter24hourdwell. Testingconsistedof5cyclesof10minuteimmersionsinthespecifiedchemicalreagentfollowedby30minuterecoveryperiod. CHEMICALREAGENT SUBJECTIVEOBSERVATIONOFVISUALCHANGE APPEARANCEOF LABELSTOCK APPEARANCEOF LASERPRINT MethylEthylKetone Novisibleeffect Printremoved 1,1,1Trichloroethane Toluene FreonTMS IsopropylAlcohol MineralSpirits JP4JetFuel ASTM#3Oil Mil5606Oil Skydrol500B4 SuperAgitene DeionizedWater 3%AlconoxDetergent 10%SodiumHydroxideSolution 10%SulfuricAcidSolution Novisibleeffect Novisibleeffect Novisibleeffect Novisibleeffect Novisibleeffect Novisibleeffect Novisibleeffect Novisibleeffect Novisibleeffect Novisibleeffect Novisibleeffect Novisibleeffect Novisibleeffect Novisibleeffect Printremoved Printremoved Novisibleeffect Novisibleeffect Novisibleeffect Novisibleeffect Novisibleeffect Novisibleeffect Printremoved Novisibleeffect Novisibleeffect Novisibleeffect Novisibleeffect Novisibleeffect Producttesting,customerfeedback,andhistoryofsimilarproducts,supportacustomerperformanceexpectationofatleasttwo yearsfromthedateofreceiptforthisproductaslongasthisproductisstoredinitsoriginalpackaginginanenvironment below80degreesF(27C)and60%RH.Weareconfidentthatourproductwillperformwellbeyondthistimeframe.However, itremainstheresponsibilityoftheusertoassesstheriskofusingsuchproduct.Weencouragecustomerstodevelopfunctional testingprotocolsthatwillqualifyaproduct'sfitnessforuse,intheiractualapplications. Trademarks:

AlconoxisaregisteredtrademarkofAlconoxCo. FreonisaregisteredtrademarkofDuPontdeNemours,E.I.andCompany. LasertabisaregisteredtrademarkofBradyWorldwideInc. PolykenisatrademarkofTestingMachinesInc. SkydrolisaregisteredtrademarkoftheMonsantoCompany SunlighterisatrademarkoftheTestLabApparatusCompany SuperAgiteneisaregisteredtrademarkofGraymillsCorporation ASTM:AmericanSocietyforTestingandMaterials(U.S.A.) CSA:CanadianStandardAssociation PSTC:PressureSensitiveTapeCouncil(U.S.A.) UL:UnderwritersLaboratoriesInc.(U.S.A.) AllS.I.Units(metric)aremathematicallyderivedfromtheU.S.Conventional Units Note:Allvaluesshownareaveragesandshouldnotbeusedforspecificationpurposes. TestdataandtestresultscontainedinthisdocumentareforgeneralinformationonlyandshallnotberelieduponbyBrady customersfordesignsandspecifications,orbereliedonasmeetingspecifiedperformancecriteria.Customersdesiringto developspecificationsorperformancecriteriaforspecificproductapplicationsshouldcontactBradyforfurtherinformation. ProductcomplianceinformationisbaseduponinformationprovidedbysuppliersoftherawmaterialsusedbyBradyto manufacturethisproductorbasedonresultsoftestingusingrecognizedanalyticalmethodsperformedbyathirdparty, independentlaboratory.Assuch,Bradymakesnoindependentrepresentationsorwarranties,expressorimplied,and assumesnoliabilityinconnectionwiththeuseofthisinformation. WARRANTY Bradyproductsaresoldwiththeunderstandingthatthebuyerswilltesttheminactualuseanddetermineforthemselvestheir adaptabilitytotheirintendeduses.Bradywarrantstothebuyersthatitsproductsarefreefromdefectsinmaterialand workmanship,butlimitsitsobligationunderthiswarrantytoreplacementoftheproductshowntoBrady'ssatisfactiontohave beendefectiveatthetimeBradysoldit.Thiswarrantydoesnotextendtoanypersonsobtainingtheproductfromthebuyers. Thiswarrantyisinlieuofanyotherwarranty,expressorimplied,including,butnotlimitedto,anyimpliedwarrantyof merchantabilityorfitnessforaparticularpurpose,andofanyotherobligationsorliabilityonBrady'spart.Underno circumstanceswillBradybeliableforanyloss,damage,expense,orconsequentialdamagesofanykindarisinginconnection withtheuse,orinabilitytouse,Brady'sproducts. Copyright2016BradyWorldwide,Inc.|AllRightsReserved Materialmaynotbereproducedordistributedinanyformwithoutwrittenpermission. BradyNorthAmerica|6555W.GoodHopeRd|Milwaukee,WI53223|USA|Tel:4143586600|Fax:8002922289

"High Frequency Ceramic Solutions"

9/17/2015 2.45 GHz SMD Antenna, EIA 1210, Detuning resilient, Edge Mount Design Detail Specification:

This antenna is optimal for edge middle mounting; rectangular and circular PCB shape applications, go to pages 2-4 for more info. General Specifications Part Number Frequency (MHz) Peak Gain Average Gain Return Loss Operating Temperature Input/Output Power Impedance Reel Quantity Storage Temp Total Radiation Efficiency1 1Efficiency measured on 2450AT18D0100-EB1SMA 40x20mm EVB on page 2 2450AT18D0100 2400 - 2500 1.5 dBi typ. (XZ-total)

-1.0 dBi typ. (XZ-total) 10.0 dB min.

-40 to +125C 2W max. (CW) 50 3,000

-40 to +85C 72%

P/N 2450AT18D0100 Page 1 of 6 No. 1 2 Terminal Function Feeding Point GND 3 4 GND GND 4 1 Mechanical Specifications L W T a b 0.126 0.063 0.047 0.012 0.020 In 0.008 0.008 0.008

.004/-.008 0.008 mm 3.20 1.60 1.20 0.30 0.50 0.20 0.20 0.20 0.1/-0.2 0.20 b a L 3 2 w Need help designing the antenna in? Use our antenna design services! www.johansontechnology.com/ipcantennaservices 2 Free layout reviews and if you need us to tune and characterize our antenna on your design (anechoic chamber) we can do that too (lab fee may apply for the latter). Mounting Considerations 1: Standard Rectangular Layout Mount these devices with the red square mark facing up. Otherwise, the antenna will not operate as intended. 1.0 2.0 1.0 b T 0.6 0.7 0.6 4.1 Ground 6.0 Solder Resist Ground Land 0 Ohm 50 Trace (Grounded CPWG type is preferred) GND Vias Want the layout file of this? Send us a message at:

Ground www.johansontechnology.com/ask-a-question 4.0 No ground, metal PCB layers, or other metallic components like batteries directly underneath antenna!

Matching Circuits2 2It is recommended that the designer leave available slots for a "pi" (or shunt-series-shunt) network, even if all slots won't be used, this will prepare the PCB for the final mass production values of the matching circuit. The antenna matching network values above are used when antenna is mounted on Johanson's evaluation board. The matching values on clients PCB will be different. Go to:

http://johansontechnology.com/tuning and see how to obtain the new values yourself if you have a network analyzer. www.johansontechnology.com 4001 Calle Tecate Camarillo, CA 93012 TEL 805.389.1166 FAX 805.389.1821 Ver 3.0 2015 Johanson Technology, Inc. All Rights Reserved

"High Frequency Ceramic Solutions"

2.45 GHz SMD Antenna, EIA 1210, Detuning resilient, Edge Mount Design Detail Specification: 04/04/12 This antenna is optimal for edge middle mounting; rectangular and circular PCB shape applications, go to pages 2-4 for more info. Mounting Considerations 1: Standard Rectangular Layout (continued) P/N 2450AT18D0100 Page 2 of 6 Matching Circuits Via

) 6.0 No 4.0 20mm Feeding Line Measured total radiated efficiency of 2450AT18D0100 on this EVB: 72%

Ground Vias (put these all around your PCB, they will increase the antenna's 40mm Orderable EVB p/n (comes with 1 female SMA connector mounted on the opposite side):

2450AT18D0100-EB1SMA We offer 2 free layout reviews as well as antenna tuning and characterization services (lab fee may apply). For more info go to:

www.johansontechnology.com/ipcantennaservice Want the layout file of the above? Send us a message at: www.johansontechnology.com/ask-a-question To order a pre-tuned 50 EVB with a female SMA connector you see above Click here:

www.johansontechnology.com/request-a-sample Reference p/n: 2450AT18D0100-EB1SMA Mounting Considerations 2: Small clearance or "thin edge" applications Solder Resist Reserve for Pi-matching circuit3 1.0 2.0 1.0 Land

Units in mm 0.6 2.8 3.4 Ground 0.6 0.7 0.6 8.0 Blue Area = LCD/Metal/CAN/GND/Battery etc. No ground or metals in yellow area and must be located somewhere in the middle of the assembly, not the corner Want the layout file of this example? Send us a message at:

3It is recommended that the designer leave available slots for a "pi" (or shunt-series-

shunt) network, even if all slots won't be used, this will prepare the PCB for the unpredictable final mass production version of the matching circuit. The antenna matching network values above are used when antenna is mounted on Johanson's evaluation board. The matching values on clients PCB will be different. 0.6 3.4 1.5 www.johansontechnology.com/ask-a-question Note: There's no orderable EVB available for the above reference "Mounting Considerations 2" reference design Johanson Technology, Inc. reserves the right to make design changes without notice. Please confirm the specifications and delivery conditions when placing your order. All sales are subject to Johanson Technology, Inc. terms and conditions. www.johansontechnology.com 4001 Calle Tecate Camarillo, CA 93012 TEL 805.389.1166 FAX 805.389.1821 Ver 3.0 2015 Johanson Technology, Inc. All Rights Reserved

"High Frequency Ceramic Solutions"

2.45 GHz SMD Antenna, EIA 1210, Detuning resilient, Edge Mount Design Detail Specification: 04/04/12 This antenna is optimal for edge middle mounting; rectangular and circular PCB shape applications, go to pages 2-4 for more info. Mounting Considerations 3: Thin Edge + Circular PCB applications P/N 2450AT18D0100 Page 3 of 6 50 Trace (Grounded CPWG type is preferred) Want the layout file of this example? Send us a message at:

www.johansontechnology.com/ask-a-question Ground No ground, metal PCB layers, or other metallic components like batteries and displays directly underneath antenna!

Note: There's no orderable EVB available for the above reference "Mounting Considerations 3" reference design Mounting Considerations 4: Chip antenna fed from the right

) Ground Plane Matching Circuits: It is recommended that the designer leave available slots for a "pi" (or shunt-

series-shunt) network, even if all slots won't be used, this will prepare the PCB for the final mass production values of the antenna matching securing Note: There's no orderable EVB available for the above reference "Mounting Considerations 4" reference design Johanson Technology, Inc. reserves the right to make design changes without notice. Please confirm the specifications and delivery conditions when placing your order. All sales are subject to Johanson Technology, Inc. terms and conditions. www.johansontechnology.com 4001 Calle Tecate Camarillo, CA 93012 TEL 805.389.1166 FAX 805.389.1821 Ver 3.0 2015 Johanson Technology, Inc. All Rights Reserved

"High Frequency Ceramic Solutions"

2.45 GHz SMD Antenna, EIA 1210, Detuning resilient, Edge Mount Design Detail Specification: 04/04/12 This antenna is optimal for edge middle mounting; rectangular and circular PCB shape applications, go to pages 2-4 for more info. Typical Return Loss (S11) Electrical Performance (T=25C) P/N 2450AT18D0100 Page 3 of 5 0

) 1

, 1

S

B d

-10

-20

-30 2.0 m1 2.400GHz freq=

dB(S(1,1))=-13.935 m2 2.500GHz freq=

dB(S(1,1))=-14.774 m3 2.450GHz freq=

dB(S(1,1))=-24.894 m1 m2 m3 2.2 2.4 2.6 2.8 3.0 freq, GHz Johanson Technology, Inc. reserves the right to make design changes without notice. Please confirm the specifications and delivery conditions when placing your order. All sales are subject to Johanson Technology, Inc. terms and conditions. www.johansontechnology.com 4001 Calle Tecate Camarillo, CA 93012 TEL 805.389.1166 FAX 805.389.1821 Ver 3.0 2015 Johanson Technology, Inc. All Rights Reserved

"High Frequency Ceramic Solutions"

2.45 GHz SMD Antenna, EIA 1210, Detuning resilient, Edge Mount Design Detail Specification:

This antenna is optimal for edge middle mounting; rectangular and circular PCB shape applications, go to pages 2-4 for more info. Typical EM Radiation Performance (T=25C) 9/17/2015 P/N 2450AT18D0100 Page 4 of 5 TypicalRadiationPatterns XY-V/XY-H Z 180 XY cut @2.45GHz Vertical Horizontal 90 90 90 2450AT18D0100-EB1SMA Evaluation Board as AUT for all 3 scans Y 0 XY-cut scanning direction XZ-V/XZ-H Y XZ cut @2.45GHz Vertical Horizontal 180 Z 0 XZ-cut scanning direction YZ-V/YZ-H X 180

) YZ cut @2.45GHz Vertical Horizontal Z 0 YZ-cut scanning direction X 270 X 270 Y 270 Johanson Technology, Inc. reserves the right to make design changes without notice. Please confirm the specifications and delivery conditions when placing your order. All sales are subject to Johanson Technology, Inc. terms and conditions. www.johansontechnology.com 4001 Calle Tecate Camarillo, CA 93012 TEL 805.389.1166 FAX 805.389.1821 Ver 3.0 2015 Johanson Technology, Inc. All Rights Reserved

"High Frequency Ceramic Solutions"

2.45 GHz SMD Antenna, EIA 1210, Detuning resilient, Edge Mount Design Detail Specification:

This antenna is optimal for edge middle mounting; rectangular and circular PCB shape applications, go to pages 2-4 for more info. Part Number Explanation 9/17/2015 P/N 2450AT18D0100 Page 5 of 5 P/N Suffix Packing Style EVB p/n Recommended Storage Conditions of uninstalled product still on T&R Bulk T & R 2450AT18D0100-EB1SMA Suffix = S Suffix = E eg.2450AT18D0100S e.g.. 2450AT18D0100E

+5 ~ +35 C, Humidity 45~75%RH, 18 mos. Max Antenna layout review, tuning, and characterization services www.johansontechnology.com/ipcantennaservices More SMD Chip Antennas at:

www.johansontechnology.com/antennas Soldering Information www.johansontechnology.com/ipcsoldering-profile Antenna layout and tuning techniques (How to obtain the new antenna matching values) www.johansontechnology.com/tuning Packaging information RoHS Compliance MSL Info www.johansontechnology.com/ipcpackaging.html www.johansontechnology.com/technical-notes/rohs-compliance.html www.johansontechnology.com/technical-notes/msl-rating.html P/N Explanation and Breakdown www.johansontechnology.com/ipc-pn-explained Johanson Technology, Inc. reserves the right to make design changes without notice. Please confirm the specifications and delivery conditions when placing your order. All sales are subject to Johanson Technology, Inc. terms and conditions. TechnicalAuthor:ManuelCarmona www.johansontechnology.com 4001 Calle Tecate Camarillo, CA 93012 TEL 805.389.1166 FAX 805.389.1821 Ver 3.0 2015 Johanson Technology, Inc. All Rights Reserved

Dmitriy Moskovkin Manager Codes Standards & Compliance Modular Approval Letter DATE: April 3rd, 2022 Dear Application Examiner:

Leviton manufacturing Co Incs Zigbee BLE Module C0945 FCC ID 2ASLN-ZBMG2 is seeking modular approval. The radio meets the requirements for modular approval as detailed in FCC 15.212. Compliance to each of the requirements is described below:

1. The modular transmitter must have its own RF shielding. The radio portion of the module is contained in its own RF shielding. The shielding is installed at the factory. Please see the Internal Photos exhibit. 2. The modular transmitter must have buffered modulation/data inputs. The EUT has buffered data inputs to insure compliance with Part 15 requirements under conditions of excessive data rates or over-modulation. Please see the Schematics exhibit. 3. The modular transmitter must have its own power supply regulation. The EUT has its own power supply regulation to insure compliance with Part 15 requirements regardless of the quality or level of external DC supplying the module from the host unit. Please see Schematics exhibit. Also, the technical report exhibit contains AC power line conducted emissions data taken with the EUT powered from a linear power supply that contains no EMC suppression components. 4. The modular transmitter must comply with the antenna requirements of Section 15.203 and 15.204(c). The EUT meets the FCC antenna requirements. Please see Antenna information exhibit and internal photos exhibit. 5. The modular transmitter must be tested in a stand-alone configuration. The EUT was tested in a stand-alone configuration. Please see test setup photos exhibit and technical report exhibit. 6. The modular transmitter must be labeled with its own FCC ID number. The EUT is labeled with its own FCC ID number. Please see FCC ID label & location exhibit. If the FCC ID number will not be visible when the module is installed inside a host device, another label with the FCC ID will be applied to the exterior of the host device. Please see external photos exhibit for host label. 7. The modular transmitter must comply with any specific rule or operating requirements applicable to the transmitter and the manufacturer must provide adequate instructions along with the module to explain any such requirements. The EUT is compliant with all applicable FCC rules. Detail instructions for maintaining compliance are given in the User Manual. 8. The modular transmitter must comply with any applicable RF exposure requirements. The EUT is compliant with all applicable RF exposure requirements. Please see RF Exposure Exhibit. Please contact me if you have additional questions. Your attention to this matter is greatly appreciated. Best regards, Dmitriy Moskovkin Manager, Codes, Standards and Compliance 10385 SW Avery Tualatin, OR 97062 Leviton Manufacturing Co., Inc. 10385 SW Avery Tualatin, OR 97062 T: (503) 404-5570 www.leviton.com

Dmitriy Moskovkin Manager Codes Standards & Compliance April 3rd, 2022 Subject: Confidentiality Request for: FCC ID 2ASLN-ZBMG2 Pursuant to FCC 47 CFR 0.457(d) and 0.459, the applicant requests that a part of the subject FCC application be held confidential. Exhibits Block Diagram External Photos Internal Photos Operational Description Schematics Test Setup Photos Users Manual Confidentiality Requested Long-Term Short-Term Short-Term Long-Term Long-Term Short-Term Short-Term Leviton Manufacturing Co. Inc. has spent substantial effort in developing this product and it is one of the first of its kind in industry. Having the subject information easily available to "competition" would negate the advantage they have achieved by developing this product. Not protecting the details of the design will result in financial hardship. Long-Term Confidentiality:

The applicant requests the exhibits selected above Long-Term confidential be withheld from public review for the Long-Term Confidentiality period allowed. Short-Term Confidentiality:

The applicant requests the exhibits selected above as Short-Term confidential be withheld from public view for a period of 180 (specify number of days not to exceed 180) days from the date of the Grant of Equipment Authorization and prior to marketing. This is to avoid premature release of sensitive information prior to marketing or release of the product to the public. When the device is marketed the grantee must inform the TCB (for TCB grants of certification) or FCC (for FCC grants of certification) to release the Short-Term Confidentiality information withheld on the FCC equipment authorization website. Sincerely, By:

(Signature / Manager Codes Standards & Compliance) __________________________ Dmitriy Moskovkin

(Print name) Leviton Manufacturing Co., Inc. 10385 SW Avery Tualatin, OR 97062 T: (503) 404-5570 www.leviton.com