FCC ID: QGH-B167601 Lumina Wall Dimmer and Wireless Load Control Dimmer

RF Wireless Load Control 20A Switching Relay, RF Wireless Load Control 0-10V Dimmer and RF Wireless Load Control 800W Dimmer Cat. Nos. LU20S, LU107 and LU04P PK-A3314-10-00-2A-X3 WARNINGS TO AVOID FIRE, SHOCK, OR DEATH; TURN OFF POWER AT CIRCUIT BREAKER OR FUSE AND TEST THAT POWER IS OFF BEFORE WIRING!

To be installed and/or used in accordance with appropriate electrical codes and regulations. If you are unsure about any part of these instructions, consult an electrician. CAUTIONS Use this device with copper or copper clad wire only. For indoor applications only. SAVE THESE INSTRUCTIONS. INSTALLATION INSTRUCTIONS ENGLISH 2. Strip wires 3/4 in and connect as per wiring diagram. Ensure wires are firmly attached and there is no exposed copper. Product Description The Leviton Lumina RF Load Controllers are components within a Lumina RF Standalone Platform and must be paired with a Lumina RF Room Controller. The LU20S contains a power supply and a 20A relay to provide remote control switching of lighting, motor loads, and plug load control. The LU107 Load Controller is designed for 0-10V dimming loads and to be used for individual or groups of luminaires up to 10A. The LU04P supports individual or groups of luminaires with phase cut dimming of loads up to 800W. Lumina RF devices communicate with each other via 2.4 GHz radio frequency. Each wireless device in the system is designed to act as a repeater and will re-

transmit the RF signal from one device to another to ensure the signal is received by its intended device. There are several basic system components:

Lumina RF SA App: Bluetooth-enabled, wirelessly communicates with the Room Controller to configure the system. Lumina RF Room Controllers: these are used to coordinate and control all of the wireless devices in a specified space or room. It manages all energy management functionality both as required by code and as desired by the user. Contains a Bluetooth radio to connect to mobile device with the Lumina RF SA App. Provides dimming, switching, and scene control. Lumina RF Load Controllers: controls individual or groups of fixtures or receptacles for plug load control. Allows for wireless dimming and ON/OFF control of fixtures or receptacles. Lumina RF Switches and Dimmers: provide ON/OFF, 0-10V dimming, or Phase Cut dimming of luminaires. Adds 3-way control of luminaires for spaces with multiple entries. Lumina RF Occupancy Sensors: adds occupancy or vacancy sensing to the system. Lumina RF Photocell: adds daylight harvesting to the system. NOTE: Each room requires a Room Controller. Before Installation Install to outside or inside of junction box or outside of luminaire. If mounted inside, a plastic cover must be used (metal will limit the RF signal). LU107 uses 0-10Vdc low voltage control wires which may be installed as Class 1 or Class 2. NOTE (LU107): 0-10V Control Wiring - Connect the violet wire to the + 0-10V line and the gray wire to the 0-10V common using Class 1 or Class 2 wiring methods as indicated in these instructions, ballast/fixture/driver instructions or ballast/fixture/

driver label markings. Observe all requirements of any authority having jurisdiction with respect to wire type, sleeving, isolation methods, and the like. Installation WARNING: TO AVOID FIRE, SHOCK, OR DEATH; TURN OFF POWER at circuit breaker or fuse and test that power is off before wiring!

1. Mount the Load Control device to junction box or luminaire through 1/2 in hole or knockout and secure with provided locknut. ATTENTION: For LU04P, ensure the thermal pad is in contact with the metal junction box. LU04P is not to be installed in enclosed junction box. thermal pad LU04P Violet Gray Sleeve Black Blue White 0-10 VDC White Ballast/LED Driver a. LU107 Wiring Diagram Electrical Box Connectors Hot (Black) Black Line Green Ground Neutral (White) b. LU20S Wiring Diagram Blue Hot (Black) White Line 120/277VAC, 50/60Hz. Black Load White Green Ground c. LU04P Wiring Diagram Neutral (White) Blue Black Hot (Black) Black Load White White Green Ground Line 120 VAC, 60Hz Neutral (White) 3. Restore power at circuit breaker or fuse. 4. Using the Lumina RF SA App, connect to room controller to set up device and configure your system. From Factory Default, the LU107 and LU20S are in auto join mode. For the LU04P, press and hold the button for 7 seconds, then release the button. The locator light will blink amber. Press and release the button without holding. The locator light will flash green and the device will be in join mode. When the LU04P is added to the system by the room controller, the locator light will blink green 3 times. If it fails to be added, the locator light will blink red 3 times Operation The Load Control device can be turned ON and OFF automatically when the room controller is paired with a Lumina RF Occupancy Sensor and/or photocell for daylighting. When configured with an occupancy sensor, the Load Control device can be programmed for Auto ON (turns ON when occupancy is detected) or Manual ON (turns ON when a Room Controller or switch is engaged). The Load Controllers will turn OFF when occupancy is no longer detected. 2019 Leviton Mfg. Co., Inc. PK-A3314-10-00-2A-X3 Configuration and Programming 1. System Configuration is performed using the Leviton Lumina RF SA application, downloadable from Google Play or the Apple Store, using any Bluetooth enabled Android or iOS device. Use the application to:

a. Manually add/remove devices to or from the room. b. Add additional keypads, load controllers, sensors, switches or dimmers to the c. Change Sensor Parameters like Sensitivity, Timeout, target light level, and room. other settings. d. Create user defined groups of fixtures. e. Define Scenes (Meeting, Presentation, Lunch, Dinner, Test, etc.). 2. Factory Default: resets device to out of the box state. a. For LU20S and LU107:

Push button on device for more than 20 seconds (but less than 25). Locator light will blink AMBER at 5 and 20 second intervals.NOTE: release button after 20 second light flash. Release button. When complete, device will reboot then revert to auto join mode where it is searching for a network to join. Locator light will blink GREEN slowly while looking for an open network. b. For LU04P:

amber. Press and hold button for 14 seconds. The locator light quickly flash red/

Release button. When reset is complete, device will reboot. Follow the LU04P instructions in Installation section to add it into a system. Catalog Nos. Input Voltage/Frequency Input Current SPECIFICATIONS LU20S-DNW Switching Relay 120-277VAC, 50/60Hz LU107-DNW 0-10V Dimmer, 50 mA Sink 120-277VAC, 50/60Hz LU04P-1NW Phase Cut Dimmer 120VAC, 60Hz 120V 277V Standby: 0.2W Max: 0.5W+Load Current Standby: 0.3W Max: 0.6W+Load Current Standby: 0.2W Max: 0.5W+Load Current Standby: 0.3W Max: 0.6W+Load Current Standby: 1.0W Max: 1.2W+Load Current Not rated for use Load Ratings General Purpose Rating @ 120V 20A LED, CFL, Electronic Ballast @ 120V 10A LED, CFL, Electronic Ballast @ 277V 10A Mark 10 @ 120V Not rated for use Magnetic Ballast @ 120V 10A Magnetic Ballast @ 277V 10A Resistive, Tungsten @ 120V 6.67A Resistive, Tungsten @ 277V 6.67A Motor @ 120V 1/4Hp (FLA 5.8A) Motor @ 277V 1/3Hp (FLA 3.0A) IP Rating Network Connections Operating Temperature Storage Temperature Purpose of Control Action Control Type Pollution Degree Impulse Voltage Not rated for use 360W Not rated for use 800VA 800W Not rated for use 800W Not rated for use Not rated for use Not rated for use Not rated for use 8A 5A Not rated for use 10A 10A 6.67A 6.67A 1/4Hp (FLA 5.8A) 1/3Hp (FLA 3.0A) IP30 0C - 50C (32F - 122F)

-40C to 85C (-40F - 185F) Operating control 1 2 IEEE 802.15.4, 2.4GHz, wireless, mesh network up to 75 ft range between device 4000V 4000V 2500V Statement Caution Changes or modifications not expressly approved by Leviton Manufacturing Co., could void the users authority to operate the equipment. FCC Statement:

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. IC Statement This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device."

TRADEMARK DISCLAIMER Use herein of third party trademarks, service marks, trade names, brand names and/or product names are for informational purposes only, are/may be the trademarks of their respective owners; such use is not meant to imply affiliation, sponsorship, or endorsement. Lumina is a registered trademark of Leviton Manufacturing Co., Inc. Bluetooth is a trademark of Bluetooth SIG. Android is a registered trademark of Google, LLC. iOS is a trademark of Cisco. Mark 10 is a registered trademark of Advance Transformer Co. RF EXPOSURE AND CO-LOCATION:

To comply with FCC and ISED RF exposure limits for general population / uncontrolled exposure this device should be installed and operated with a minimum distance of 7.9 inches (20 cm) between the radiator and your body. This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter. FOR CANADA ONLY For warranty information and/or product returns, residents of Canada should contact Leviton in writing at Leviton Manufacturing of Canada Ltd to the attention of the Quality Assurance Department, 165 Hymus Blvd, Pointe-Claire (Quebec), Canada H9R 1E9 or by telephone at 1 800 405-5320. Leviton warrants to the original consumer purchaser and not for the benefit of anyone else that this product at the time of its sale by Leviton is free of defects in materials and workmanship under normal and proper use for five years from the purchase date. Levitons only obligation is to correct such defects by repair or replacement, at its option. For details visit www.leviton.com or call 1-800-824-3005. This warranty excludes and there is disclaimed liability for labor for removal of this product or reinstallation. This warranty is void if this product is installed improperly or in an improper environment, overloaded, misused, opened, abused, or altered in any manner, or is not used under normal operating conditions or not in accordance with any labels or instructions. There are no other or implied warranties of any kind, including merchantability and fitness for a particular purpose, but if any implied warranty is required by the applicable jurisdiction, the duration of any such implied warranty, including merchantability and fitness for a particular purpose, is limited to five years. Leviton is not liable for incidental, indirect, special, or consequential damages, including without limitation, damage to, or loss of use of, any equipment, lost sales or profits or delay or failure to perform this warranty obligation. The remedies provided herein are the exclusive remedies under this warranty, whether based on contract, tort or otherwise. LIMITED 5 YEAR WARRANTY AND EXCLUSIONS 2019 Leviton Mfg. Co., Inc. For Technical Assistance Call: 1-800-824-3005 (U.S. Only) or 1-800-405-5320 (Canada Only) www.leviton.com PK-A3314-10-00-2A-X3 ARTWORK PRINT SPECIFICATIONS PART NUMBER PK-A3314-10-00-2A-X3 REV DESCRIPTION Instruction Sheet Artwork must be printed at 100% (1:1 scale) Color(s):

1 over 1 Fonts:

Helvetica Black x Spot CMYK For manuals - designates cover specifications Fold Line Kiss Cut Cellophane Glue Die Line Key:

Die Cut Perforate MANUAL INTERIORS / BINDERY / FOLD SCHEME :

Color(s):

over Fonts:

1:

2:

3:

4:

1:

2:

3:

4:

Spot CMYK 1:

2:

3:

4:

1:

2:

3:

4:

Die cut x Fold Saddle Stitch Perfect Bind Drill Trim DIMENSIONS / FOLD SCHEME / BINDERY DIAGRAM 8.5"

Part No. 11"

2.125"

2.75"

Part No. Die Cut Fold Line Punch/Drill Hole The information in this document is the exclusive PROPRIETARY property of LEVITON MANUFACTURING COMPANY, INC. It is disclosed with the understanding that acceptance or review by the recipient constitutes an undertaking by the recipient. (1) to hold this information in strict confidence, and (2) not to disclose, duplicate, copy, modify or use the information for any purpose other than that for which disclosed. FOR LEVITON USE ONLY Approvals:

Plant 08 J. Tang x CQA cc: H. Cai x x Eng R. Brown Other M. Blonder PN-ARN:

EM0301-6268 ECR Number:

Released Artwork Format: Production PDF Artwork Release Date:

PM A. Rogowicz cc: R. Parks, L. Pukhrambam x x x S & A D. Moskovkin cc: F. Tse Other V. LoNigro Pilot Rev:

X3 Artwork Print Specification Sheet Rev A12.eps SPECIFICATIONS :

Thickness:

40 lb. Material:

Finish:

Body Material:

Thickness:

Bindery PROCESS :

x Offset Flexo Other Line Screen:

Angle:

Resolution:

COMMENTS :

Mktg Cust Artist:

L. Walsh Notes:

0-10VDC RF Wall Dimmer Cat. No. ZS057-D0Z, Ratings: 120-277VAC, 50/60Hz. Cat. No. ZS057-30Z, Ratings: 347VAC, 50/60Hz. INSTALLATION INSTRUCTIONS DI-000-ZS057-02B-X1 ENGLISH CAUTIONS Use this device with copper or copper clad wire only. For indoor applications only. Save these instructions. WARNINGS TO AVOID FIRE, SHOCK, OR DEATH; TURN OFF POWER AT CIRCUIT BREAKER OR FUSE AND TEST THAT POWER IS OFF BEFORE WIRING!

To be installed and/or used in accordance with appropriate electrical codes and regulations. If you are unsure about any part of these instructions, consult an electrician. Before Installation Install into any single gang device back box. Support Multi-gang installations. Require Decora faceplate, sold separately. Devices use 0-10Vdc low voltage control wires which may be installed as Class 1 or Class 2. IMPORTANT NOTE: If installed as Class 2, all devices in the circuit must be Class 2 rated and this switch must be wired per instructions below. Class 2 Installation:

As required under NEC code NFPA 70, paragraph 725.136 (d), the Class 2 0-10V (gray and violet) control wires must be mechanically separated from Class 1 wiring (line, neutral and ground power lines) when located within the same electrical box. This is accomplished by installing a mechanical barrier such as silicone tubing or other non-conducting sleeve over the length of 0-10V control wires. When product is used with 120VAC power source and the 0-10V control wires are connected to CL3, CL3R or CL3P rated control cables (or permitted substitute), then silicone tubing or other non-conducting sleeve is required over the control wires for the entire wire length from the device to the location where the wires exit the box. Tubing is not required on the CL3, CL3R or CL3P between the wire connector and extending out of the electrical box. When used with 277VAC power source and the 0-10V control wires are connected to CL3, CL3R or CL3P rated control cables (or permitted substitute), then silicone tubing or other non-conducting sleeve is required over the control wires for the entire wire length from the device to the location where the wires exit the box. Tubing is also required on the CL3, CL3R or CL3P between the wire connector and extending out of the electrical box. NOTE:

Silicone tubing should be NRTL (UL/CSA/ETL) recognized or equivalent to provide mechanical separation equal to .25 in air. Connectors joining 0-10V control wires should be approved LISTED CONNECTORS. Wire connectors and wire tubing should be provided by the installation contractor. Installation WARNING: TO AVOID FIRE, SHOCK, OR DEATH;

TURN OFF POWER at circuit breaker or fuse and test that power is off before wiring!

1. Strip wires 3/4" and connect as per wiring diagram. Ensure wires are firmly attached and there is no exposed copper. Line Electrical Box Connectors Violet Gray Sleeve Black Blue White 0-10 VDC White Ballast/LED Driver Hot (Black) Black Green Ground Neutral (White) Class 1 installation shown (for Class 2, refer to notes) 2. Gently place the wires and your device into the wall box and attach with screws provided. 3. Restore power and test ON/OFF operation. LED locator light should be ON when switch power is turned OFF. White Blue Black Load Neutral Line (Hot) Green Ground Violet Gray 4. If desired, change switch color. 5. Install Decora faceplate. 2019 Leviton Mfg. Co., Inc. DI-000-ZS057-02B-X1 To release, push sides. Line up and press in to attach. Installation (cont'd) 6. Enroll Device and configure your system. Using your system, you may be able to program different functionality, such as pushing the top of the paddle for a presentation scene or pushing the bottom of the paddle for OFF. PADDLE TOP - ON ROCKER UP - Tap to raise 3%. Push and hold to raise until released. BRIGHTNESS INDICATORS LEDs indicate brightness level. PADDLE BOTTOM - OFF LOCATOR LED - on when switch is off so you can find your control ROCKER DOWN - Tap to lower 3%. Push and hold to lower until released. Configuration and Programming Control functionality, LED Behavior, and user interaction can be adjusted based on the features of your system. Please refer to your system documentation for details. Enrollment Out of the box, the device is in Auto Join mode and is always active and attempting to join an open network. If you need to add your device to a network and it is not in auto join mode, reset to factory default and it will start searching for a network. o Locator LED will blink GREEN slowly while looking for an open network. Factory Default resets device to out of the box state o Push top or bottom of paddle for approximately 20 seconds until the locator LED flashes AMBER the second time. o Release paddle. o Locator LED will alternate between green/amber while device is resetting, and turn off when complete. o When complete, device will reboot then revert to auto join mode where it is searching for a network to join. Locator LED will blink GREEN slowly while looking for an open network. Status Check o Push top or bottom of paddle for 5 seconds until the locator LED flashes AMBER once. o Release paddle. o The locator LED will blink to indicate device state. One RED blink: device unconfigured. Three GREEN blinks: Connected to network, network formed. NOTE: holding the top or bottom of the paddle for 25 seconds or greater will abandon all programming and return to normal operation. You will know youve hit the 25 second mark because the locator LED will flash AMBER the third time. Input Voltage/Frequency 120-277VAC, 50/60Hz. 347VAC, 50/60Hz. SPECIFICATIONS ZS057-D0Z ZS057-30Z FCC COMPLIANCE STATEMENT:

FCC ID: QGH-B167601 Catalog Nos. Input Current 120V 277V 347V Magnetic Ballast @ 120V Magnetic Ballast @ 277V Magnetic Ballast @ 347V Resistive, Tungsten @ 120V Resistive, Tungsten @ 277V Resistive, Tungsten @ 347V Motor @ 120V Motor @ 277V Motor @ 347V IP Rating Network Connections Operating Temperature Storage Temperature UL Pollution Degree UL Impulse Voltage Load Ratings LED, CFL, Electronic Ballast @ 120V LED, CFL, Electronic Ballast @ 277V LED, CFL, Electronic Ballast @ 347V Not rated for use 4A, 1388VA Not rated for use receiver is connected. Standby: 0.2W Max: 0.5W+Load Current Standby: 0.3W Max: 0.6W+Load Current Not rated for use Not rated for use Not rated for use 0.5+load 8A 5A 10A 10A 6.67A 6.67A Not rated for use 1/4Hp (FLA 5.8A) 1/3Hp (FLA 3.0A) Not rated for use IP10 Not rated for use Not rated for use Not rated for use Not rated for use 3.45A, 1200VA Not rated for use Not rated for use 800W Not rated for use Not rated for use 1/4Hp 0C - 40C (32F - 104F)

-40C to 85C 2 6000V The enclosed device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(i.) This device may not cause harmful interference (ii.) This device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by Leviton could void the users authority to operate this equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Connect the equipment into an outlet on a circuit different from that to which the Increase the separation between the equipment and receiver. Consult the dealer or an experienced radio/TV technician for help. RF EXPOSURE AND CO-LOCATION:

To comply with FCC and ISED RF exposure limits for general population /

uncontrolled exposure this device should be installed and operated with a minimum distance of 7.9 inches (20 cm) between the radiator and your body. This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter. This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. IMPORTANT! Any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate this equipment. This Class B digital apparatus complies with Canadian ICES-003. IEEE 802.15.4, 2.4Ghz, wireless, mesh network up to 75' range between device IC: 2473A-B167601 INDUSTRY CANADA COMPLIANCE STATEMENT:

FOR CANADA ONLY For warranty information and/or product returns, residents of Canada should contact Leviton in writing at Leviton Manufacturing of Canada ULC to the attention of the Quality Assurance Department, 165 Hymus Blvd, Pointe-Claire (Quebec), Canada H9R 1E9 or by telephone at 1 800 405-5320. Leviton warrants to the original consumer purchaser and not for the benefit of anyone else that this product at the time of its sale by Leviton is free of defects in materials and workmanship under normal and proper use for two years from the purchase date. Levitons only obligation is to correct such defects by repair or replacement, at its option. For details visit www.leviton.com or call 1-800-824-3005. This warranty excludes and there is disclaimed liability for labor for removal of this product or reinstallation. This warranty is void if this product is installed improperly or in an improper environment, overloaded, misused, opened, abused, or altered in any manner, or is not used under normal operating conditions or not in accordance with any labels or instructions. There are no other or implied warranties of any kind, including merchantability and fitness for a particular purpose, but if any implied warranty is required by the applicable jurisdiction, the duration of any such implied warranty, including merchantability and fitness for a particular purpose, is limited to two years. Leviton is not liable for incidental, indirect, special, or consequential damages, including without limitation, damage to, or loss of use of, any equipment, lost sales or profits or delay or failure to perform this warranty obligation. The remedies provided herein are the exclusive remedies under this warranty, whether based on contract, tort or otherwise. LIMITED 2 YEAR WARRANTY AND EXCLUSIONS 2019 Leviton Mfg. Co., Inc. For Technical Assistance Call: 1-800-824-3005 (USA Only) or 1-800-405-5320 (Canada Only) www.leviton.com DI-000-ZS057-02B-X1 ARTWORK PRINT SPECIFICATIONS PART NUMBER DI-000-ZS057-02B-X1 REV DESCRIPTION Instruction Sheet Artwork must be printed at 100% (1:1 scale) Color(s):

1 over 1 Fonts:

Helvetica Black x Spot CMYK For manuals - designates cover specifications Fold Line Kiss Cut Cellophane Glue Die Line Key:

Die Cut Perforate MANUAL INTERIORS / BINDERY / FOLD SCHEME :

Color(s):

over Fonts:

1:

2:

3:

4:

1:

2:

3:

4:

Spot CMYK 1:

2:

3:

4:

1:

2:

3:

4:

Die cut x Fold Saddle Stitch Perfect Bind Drill Trim DIMENSIONS / FOLD SCHEME / BINDERY DIAGRAM 8.5"

Part No. 11"

2.75"

Part No. 4.25"

FINAL Die Cut Fold Line Punch/Drill Hole SPECIFICATIONS :

Thickness:

40 lb. Material:

Finish:

Body Material:

Thickness:

Bindery PROCESS :

x Offset Flexo Other Line Screen:

Angle:

Resolution:

COMMENTS :

The information in this document is the exclusive PROPRIETARY property of LEVITON MANUFACTURING COMPANY, INC. It is disclosed with the understanding that acceptance or review by the recipient constitutes an undertaking by the recipient. (1) to hold this information in strict confidence, and (2) not to disclose, duplicate, copy, modify or use the information for any purpose other than that for which disclosed. FOR LEVITON USE ONLY Approvals:

Plant 08 J. Tang x cc: H. Cai Mktg Cust Notes:

CQA Eng Other x x x x x PM D. Buerer S & A D. Moskovkin Other PN-ARN:

ECR18681-6168 ECR Number:

ECR18681 Pilot Rev:

Artist:

K.MARKELL Released Artwork Format: Production PDF Artwork Release Date:

Artwork Print Specification Sheet Rev A12.eps

Gradateurs RF de 0-10 V c.c. No de cat. ZS057-D0Z, Valeurs nominales : 120-277 V c.a., 50/60Hz. No de cat. ZS057-30Z, Valeurs nominales : 347 V c.a., 50/60Hz. DIRECTIVES DI-000-ZS057-52B-X1 FRANAIS AVERTISSEMENTS POUR VITER LES RISQUES DINCENDIE, DE DCHARGE OU DLECTROCUTION, COUPER LE COURANT AU FUSIBLE OU AU DISJONCTEUR ET SASSURER QUE LE CIRCUIT EST BIEN COUP AVANT DE PROCDER AU CBLAGE MISES EN GARDE Les produits viss aux prsentes ne doivent tre utiliss quavec du fil de cuivre ou plaqu cuivre. Les produits viss aux prsentes sont pour lintrieur Les produits viss aux prsentes doivent tre installs et utiliss conformment aux codes seulement. Conserver les prsentes directives. dfaut de bien comprendre les prsentes directives, en tout ou en partie, on doit faire de llectricit en vigueur. appel un lectricien. Prparation Les produits viss aux prsentes peuvent tre installs dans nimporte quelle bote murale pour un dispositif. Ils peuvent faire partie dinstallations groupes. Ils requirent une plaque DecoraMD (vendue sparment). Ils emploient des fils de commande basse tension de 0-10 V c.c. qui peuvent tre raccords comme tant de classe 1 ou 2. REMARQUE IMPORTANTE : si on choisit la classe 2, tous les dispositifs du circuit doivent pouvoir la prendre en charge, et les produits viss aux prsentes doivent tre raccords suivant les directives qui suivent. Installation de classe 2 :

Comme le requiert le code amricain de llectricit (NFPA 70, paragraphe 725.136 [d]), les fils de commande de classe 2 (gris et violet de 0-10 V) doivent tre mcaniquement isols de ceux de classe 1 (ligne, neutre et terre de lalimentation) quand ils sont dans la mme bote. Pour ce faire, on peut employer des tubes de silicone ou un autre type de manchons non conducteurs sur toute la longueur des fils de commande. Quand le produit est aliment par une source de 120 V c.a. et les fils de commande de 0-10 V sont connects des cbles cote CL3, CL3R ou CL3P (ou des substituts permis), les tubes de silicone ou les manchons non conducteurs doivent les recouvrir sur toute la longueur, du dispositif lendroit o ils sortent de la bote. Aucune protection nest requise sur les cbles entre le capuchon de connexion et la partie qui sort de la bote. Quand le produit est aliment par une source de 277 V c.a. et les fils de commande de 0-10 V sont connects des cbles cote CL3, CL3R ou CL3P (ou des substituts permis), les tubes de silicone ou les manchons non conducteurs doivent les recouvrir sur toute la longueur, du dispositif lendroit o ils sortent de la bote. Une telle protection est galement requise sur les cbles entre le capuchon de connexion et la partie qui sort de la bote. REMARQUES :

Les tubes ou manchons devraient avoir t approuvs par un laboratoire reconnu lchelle nationale (UL/CSA/ETL) comme tant aptes assurer une sparation mcanique gale 0,25 po (6,35 mm) dans lair. Les capuchons reliant les fils de commande de 0-10 V devraient avoir t approuvs et HOMOLOGUS. Les tubes, manchons et connecteurs devraient tre fournis par lentrepreneur charg de linstallation. Installation AVERTISSEMENT : POUR VITER LES RISQUES DINCENDIE, DE DCHARGE OU DLECTROCUTION, COUPER LE COURANT au fusible ou au disjoncteur et sassurer que le circuit est bien coup avant de procder linstallation. 1. Dnuder les fils sur 3/4 po (1,9 cm) et les raccorder conformment au schma de cblage. Sassurer que les fils sont solidement relis et quaucune section de cuivre nest expose. Bote murale Connecteurs Violet Gris Manchon Noir Blanc Bleu Blanc Ballast/

rgulateur de DEL de 0-10 V c.c. Actif (noir) Noir Ligne Neutre (blanc) Terre

(vert) Cblage de classe 1 (se reporter aux remarques pour la classe 2) 2. Insrer dlicatement les fils et le dispositif dans la bote, et assujettir le tout au moyen des vis fournies. 3. Rtablir lalimentation et vrifier les fonctions de commutation du dispositif. Le tmoin de localisation devrait sallumer quand les charges sont mises hors tension. Charge Neutre Ligne (actif) Terre Blanc Noir Noir Vert Violet Gris 4. Changer la couleur du dispositif au besoin. 5. Poser une plaque Decora. 2019 Leviton Mfg. Co., Inc. Appuyer sur les cts pour dgager. Aligner la touche et serrer les languettes latrales DI-000-ZS057-52B-X1 Installation (suite) 6. Enregistrer le dispositif et configurer le systme. Il est possible de programmer diverses fonctions, comme lactivation dune ambiance de prsentation au toucher de la partie suprieure de la bascule, par exemple. HAUT DE LA BASCULE mise sous tension INDICATEURS DINTENSIT Les DEL indiquent le niveau de luminosit. BAS DE LA BASCULE mise hors tension TMOIN DE LOCALISATION allum quand les charges sont hors tension pour pouvoir reprer la commande HAUT DE LA BARRE intensification de 3 %

par toucher. Enfoncer pour intensifier jusquau niveau voulu. BAS DE LA BARRE tamisage de 3 % par toucher. Enfoncer pour tamiser jusquau niveau voulu. Configuration et programmation Les fonctions, le comportement des tmoins et linterface utilisateur peuvent tre rgls suivant les caractristiques du systme en place. Se reporter la documentation relative ce dernier pour en savoir plus. Enregistrement par dfaut, le dispositif est en mode dintgration automatique, tentant activement de sinclure dans un rseau ouvert. Si ce mode nest pas activ, il suffit de rtablir les valeurs par dfaut du dispositif pour quil se remette chercher. o Le tmoin de localisation clignote lentement en vert quand le dispositif cherche un rseau. Rtablissement des valeurs par dfaut o Appuyer sur la partie suprieure de la bascule pendant environ 20 secondes, jusqu ce que le tmoin de localisation clignote une deuxime fois en AMBRE. o Relcher la bascule. o Le tmoin de localisation passe du vert au ambre pendant que le dispositif se rinitialise, puis steint une fois lopration complte. o Le dispositif rinitialis revient en mode dintgration automatique, cherchant un rseau ouvert. Le tmoin de localisation clignote lentement en vert quand le dispositif cherche un rseau. Vrification dtat o Appuyer sur la partie suprieure de la bascule pendant cinq secondes, jusqu ce que le tmoin de localisation clignote une fois en AMBRE. o Relcher la bascule. o Le tmoin de localisation clignotera pour indiquer ltat du dispositif :

un clignotement ROUGE pour indiquer quil na pas t configur;

trois clignotements VERTS pour indiquer quil est connect au rseau. REMARQUE : si on enfonce la partie suprieure ou infrieure de la bascule pendant 25 secondes ou plus, le dispositif sort du mode de programmation et revient en mode de fonctionnement normal. Le cas chant, le tmoin de localisation clignotera une troisime fois en AMBRE. Nos de catalogue ZS057-D0Z ZS057-30Z Tension/frquence dentre 120-277 V c.a., 50/60 Hz. 347 V c.a., 50/60 Hz. FICHE TECHNIQUE Courant dentre 120 V 277 V 347 V Charges nominales DEL, LFC et ballasts lectroniques 120 V DEL, LFC et ballasts lectroniques 277 V DEL, LFC et ballasts lectroniques 347 V Ballasts magntiques 120 V Ballasts magntiques 277 V S.O. 8 A 5 A 10 A 10 A 6,67 A 6,67 A Au repos : 0,2 W. Max :

0,5 W + courant de charge Au repos : 0,3 W. Max :

0,6 W + courant de charge S.O. S.O. Non pris en charge 4 A, 1 388 VA 0,5 W + courant de charge Non pris en charge Non pris en charge Non pris en charge Non pris en charge Non prises en charge Non prises en charge Ballasts magntiques 347 V Non pris en charge 3,45 A, 1 200 VA Charges rsistives au tungstne 120 V Charges rsistives au tungstne 277 V Charges rsistives au tungstne 347 V Non prises en charge 800 W Moteurs 120 V Moteurs 277 V Moteurs 347 V Cote dtanchit Connexions rseau 1/4 ch (5,8 APC) 1/3 ch (3,0 APC) Non pris en charge Non pris en charge Non pris en charge 1/4 ch IP10 IEEE 802.15.4, 2,4 GHz, rseau maill sans fil avec des distances maximales de 75 pi (22,9 m) entre dispositifs 0 40 C (32 104 F) Temprature de fonctionnement Temprature de rangement Niveau de pollution UL Impulsions de tension UL

-40 85 C 2 6 000 V VOISINAGE ET EXPOSITION AUX RADIOFRQUENCES :

Afin de se conformer aux exigences de la FCC et de respecter les seuils dexposition aux radiofrquences prescrits par lISDE pour le grand public

(environnements non contrls), les dispositifs dcrits aux prsentes devraient tre installs et utiliss une distance minimale de 7,9 po (20 cm) de toute personne. Ils ne doivent tre ni installs ni utiliss prs dautres antennes ou transmetteurs. DCLARATION DE CONFORMIT AUX NORMES DINDUSTRIE CANADA :

IC: 2473A-B167601 Ce produit est conforme aux exigences de la partie 15 des rglements de la FCC ainsi quaux cahiers des charges sur les normes radiolectriques dISDE pour les produits exempts de licence. Il peut tre utilis condition quil

(1) ne cause aucun brouillage prjudiciable et (2) ne soit pas affect par les interfrences dautres dispositifs susceptibles notamment den perturber le fonctionnement. Toute modification apporte sans lautorisation expresse du responsable de la conformit pourrait avoir pour effet dannuler les droits dutilisation du produit. Pour respecter les limites dintensit de champ des RF de la FCC et dISDE pour le grand public (environnements non contrls), lantenne ou les antennes employes pour ce transmetteur doivent tre places de faon maintenir une distance dau moins 20 cm de toute personne, et ne doivent tre ni installes ni utilises avec dautres antennes ou transmetteurs. Classe B. Conformit CAN ICES-3(B)/NMB-3(B) GARANTIE LIMITE DE 2 ANS ET EXCLUSIONS Leviton garantit au premier acheteur, et uniquement au crdit du dit acheteur, que ce produit ne prsente ni dfauts de fabrication ni dfauts de matriaux au moment de sa vente par Leviton, et nen prsentera pas tant quil est utilis de faon normale et adquate, pendant une priode de 2 ans suivant la date dachat. La seule obligation de Leviton sera de corriger les dits dfauts en rparant ou en remplaant le produit dfectueux si ce dernier est retourn port pay, accompagn dune preuve de la date dachat, avant la fin de la dite priode de 2 ans, la Manufacture Leviton du Canada S.R.I., au soin du service de lAssurance Qualit, 165 boul. Hymus, Pointe-Claire, (Qubec), Canada H9R 1E9. Par cette garantie, Leviton exclut et dcline toute responsabilit envers les frais de main doeuvre encourus pour retirer et rinstaller le produit. Cette garantie sera nulle et non avenue si le produit est install incorrectement ou dans un environnement inadquat, sil a t surcharg, incorrectement utilis, ouvert, employ de faon abusive ou modifi de quelle que manire que ce soit, ou sil na t utilis ni dans des conditions normales ni conformment aux directives ou tiquettes qui laccompagnent. Aucune autre garantie, explicite ou implicite, y compris celle de qualit marchande et de conformit au besoin, nest donne, mais si une garantie implicite est requise en vertu de lois applicables, la dite garantie implicite, y compris la garantie de qualit marchande et de conformit au besoin, est limite une dure de 2 ans. Leviton dcline toute responsabilit envers les dommages indirects, particuliers ou conscutifs, incluant, sans restriction, la perte dusage dquipement, la perte de ventes ou les manques gagner, et tout dommage-intrt dcoulant du dlai ou du dfaut de lexcution des obligations de cette garantie. Seuls les recours stipuls dans les prsentes, quils soient dordre contractuel, dlictuel ou autre, sont offerts en vertu de cette garantie. 2019 Leviton Mfg. Co., Inc. Ligne dAssistance Technique : 1-800-405-5320 (Canada seulement) www.leviton.com DI-000-ZS057-52B-X1 ARTWORK PRINT SPECIFICATIONS PART NUMBER DI-000-ZS057-52B-X1 REV DESCRIPTION Instruction Sheet Artwork must be printed at 100% (1:1 scale) Color(s):

1 over 1 Fonts:

Helvetica Black x Spot CMYK For manuals - designates cover specifications Fold Line Kiss Cut Cellophane Glue Die Line Key:

Die Cut Perforate MANUAL INTERIORS / BINDERY / FOLD SCHEME :

Color(s):

over Fonts:

1:

2:

3:

4:

1:

2:

3:

4:

Spot CMYK 1:

2:

3:

4:

1:

2:

3:

4:

Die cut x Fold Saddle Stitch Perfect Bind Drill Trim DIMENSIONS / FOLD SCHEME / BINDERY DIAGRAM 8.5"

Part No. 11"

2.75"

Part No. 4.25"

FINAL Die Cut Fold Line Punch/Drill Hole SPECIFICATIONS :

Thickness:

40 lb. Material:

Finish:

Body Material:

Thickness:

Bindery PROCESS :

x Offset Flexo Other Line Screen:

Angle:

Resolution:

COMMENTS :

The information in this document is the exclusive PROPRIETARY property of LEVITON MANUFACTURING COMPANY, INC. It is disclosed with the understanding that acceptance or review by the recipient constitutes an undertaking by the recipient. (1) to hold this information in strict confidence, and (2) not to disclose, duplicate, copy, modify or use the information for any purpose other than that for which disclosed. FOR LEVITON USE ONLY Approvals:

Plant 08 J. Tang x cc: H. Cai Mktg Cust Notes:

CQA Eng Other x x x x x PM D. Buerer S & A D. Moskovkin Other PN-ARN:

ECR18681-6168 ECR Number:

ECR18681 Pilot Rev:

Artist:

K.MARKELL Released Artwork Format: Production PDF Artwork Release Date:

Artwork Print Specification Sheet Rev A12.eps

Relais de commutation de 20 A, et gradateurs de 0 10 V/800 W sans fil (RF) pour la commande de charges Nos de cat. LU20S, LU107 et LU04P Une photocellule LuminaMD RF : permet dexploiter la lumire ambiante. REMARQUE : il doit y avoir un contrleur de pice dans chaque aire commander. Terre

(vert) AVERTISSEMENTS POUR VITER LES RISQUES DINCENDIE DE DCHARGE OU DLECTROCUTION COUPER LE COURANT AU FUSIBLE OU AU DISJONCTEUR ET SASSURER QUE LE CIRCUIT EST BIEN COUP AVANT DE PROCDER AU CBLAGE!

Les produits dcrits aux prsentes doivent tre installs et utiliss conformment aux codes de llectricit en vigueur. dfaut de bien comprendre les prsentes directives, en tout ou en partie, on doit faire appel un lectricien. Description des produits Les contrleurs de charges LuminaMD RF de Leviton sont des composants dune plateforme autonome qui doivent tre associs un contrleur de pice de la mme gamme. Le modle LU20S contient un bloc dalimentation et un relais de 20 A pour assurer la commande distance de charges dclairage, motorises et enfiches. Le modle LU107 est quant lui conu pour rgler une ou plusieurs charges de 0 10 V (maximum de 10 A). Finalement, le modle LU04P peut commander un ou plusieurs luminaires coupure de phase dune puissance pouvant atteindre 800 W. Les dispositifs sans fil LuminaMD RF communiquent entre eux via une frquence radio de 2,4 GHz. Chacun est conu pour agir en tant que rpteur qui retransmet les signaux RF pour faire en sorte quils soient bien reus par la commande vise. Le systme comprend plusieurs composants de base :

Lappli LuminaMD RF SA dote de la technologie BluetoothMC, elle communique sans fil avec le contrleur de pice pour configurer le systme. Un contrleur de pice LuminaMD RF : utilis pour coordonner et commander tous les dispositifs sans fil dune pice ou dun espace donn. Ces contrleurs permettent de se conformer aux exigences des utilisateurs et des codes locaux en matire de gestion de lnergie. Ils contiennent une radio Bluetooth qui leur permet de communiquer avec un appareil mobile via lappli LuminaMD RF SA. Ils peuvent ainsi rgler ou commuter des luminaires, ou encore crer des ambiances les utilisant. Des contrleurs de charges LuminaMD RF : commandent un ou plusieurs luminaires ou prises dans lesquelles divers appareils peuvent tre enfichs. Ces contrleurs sans fil permettent de commuter, dintensifier ou de tamiser lclairage. Des interrupteurs et des gradateurs LuminaMD RF : assurent la commutation et la gradation de 0 10 V ou coupure de phase de divers luminaires. Ces dispositifs permettent en outre la commande des mmes charges depuis plusieurs entres. Des dtecteurs doccupation LuminaMD RF : ajoutent des fonctions supplmentaires aux systmes. Prparation Les produits dcrits aux prsentes doivent tre installs lextrieur dun luminaire ou lintrieur dune bote de raccordement. Dans ce dernier cas, il faut employer un couvercle de plastique (le mtal nuit aux signaux RF). Le modle LU107 emploie des fils de commande basse tension de 0-10 V c.c. qui peuvent tre raccords comme tant de classe 1 ou 2. REMARQUE RELATIVE AU MODLE LU107 : pour le cblage de commande de 0-10 V, il faut raccorder le fil violet au fil de ligne et le fil gris au fil commun en employant des mthodes de classe 2, telles que dcrites aux prsentes, dans les directives des ballasts/luminaires/rgulateurs employs ou encore sur les tiquettes de ces derniers. Il faut en outre respecter les exigences de toutes les autorits en la matire en ce qui concerne les types de fil utiliser, les manchons privilgier, les mthodes disolation, etc. Installation AVERTISSEMENT : POUR VITER LES RISQUES DINCENDIE, DE DCHARGE OU DLECTROCUTION, COUPER LE COURANT au fusible ou au disjoncteur et sassurer que le circuit est bien hors tension avant de procder au cblage!

1. Fixer le dispositif de commande au luminaire ou la bote via le trou ou la dbouchure de 1/2 po (1,3 cm), en lassujettissant au moyen du contre-crou fourni. ATTENTION : il faut sassurer que lcran thermique du modle LU04P reste en contact avec la paroi mtallique de la bote. Ce modle ne peut tre install dans une bote ferme. cran thermique 2019 Leviton Mfg. Co., Inc. LU04P MISES EN GARDE Les produits dcrits aux prsentes ne doivent tre utiliss quavec du fil de cuivre ou plaqu cuivre. Les produits dcrits aux prsentes sont pour lintrieur seulement. CONSERVER LES PRSENTES DIRECTIVES. PK-A3314-10-05-2A-X3 INSTALLATION FRANAIS 2. Dnuder les fils sur 3/4 po (1,9 cm) et les raccorder conformment au schma de cblage. Sassurer que les fils sont solidement relis et quaucune section de cuivre nest expose. a. Schma de cblage du modle LU107 Connecteurs Violet Gris Manchon Noir Bleu Blanc Ballast/rgulateur Blanc de DEL de 0-10 V c.c. Electrical Box Actif (noir) Noir Line Neutre (blanc) Terre

(vert) b. Schma de cblage du modle LU20S Bleu Actif (noir) Blanc Ligne 120/277 V c.a., 50/60 Hz c. Schma de cblage du modle LU04P Neutre (blanc) Bleu Noir Actif (Noir) Blanc Terre

(vert) Ligne 120 V c.a., 60 Hz Noir Charge Blanc Noir Charge Blanc Neutre (blanc) 3. Rtablir le courant au fusible ou au disjoncteur. 4. Au moyen de lappli LuminaMD RF SA, se connecter au contrleur de pice afin de paramtrer les dispositifs et de configurer le systme. Par dfaut, les modles LU107 et LU20S sont en mode dassociation automatique. Dans le cas du modle LU04P, il faut enfoncer le bouton pendant sept secondes, puis le relcher. Le tmoin de localisation clignotera en ambre. Appuyer brivement sur le bouton. Le tmoin devrait clignoter en vert; le dispositif est alors en mode dassociation. Quand le modle LU04P aura t ajout au systme par le contrleur de pice, le tmoin clignotera en vert trois fois. Si lassociation na pas fonctionn, il clignotera plutt trois fois en rouge. Fonctionnement Le dispositif de commande de charges peut tre mis sous ou hors tension automatiquement quand le contrleur de pice est associ un dtecteur doccupation ou une photocellule pour lexploitation de la lumire ambiante. Lorsquon le configure avec un dtecteur doccupation, le dispositif de commande de charges peut tre programm pour mettre ces dernires sous tension automatiquement quand des mouvements sont capts, ou sur demande via un contrleur de pice ou un interrupteur manuel. (En mode automatique, les contrleurs de charges se mettent hors tension quand plus aucun mouvement nest dtect.) PK-A3314-10-05-2A-X3 Configuration et programmation 1. La configuration du systme seffectue depuis lappli LuminaMD RF SA de Leviton, quon peut tlcharger des boutiques en ligne Google Play ou Apple Store dans un appareil intelligent AndroidMC ou iOSMC. Cette application permet :

a. dajouter/de retirer manuellement des dispositifs;

b. dajouter des claviers, dautres contrleurs de charges, des dtecteurs, des interrupteurs ou des gradateurs;

c. de modifier les paramtres des dtecteurs (sensibilit, dlais, intensit cible, etc.);

d. de crer des groupes de luminaires;

e. de dfinir des ambiances (runion, prsentation, repas du midi, repas du soir, test, etc.). 2. Rtablissement des valeurs par dfaut a. Modles LU20S et LU107 Appuyer sur le bouton du dispositif pendant plus de 20 secondes (mais pas plus que 25 secondes). Le tmoin clignotera en ambre intervalles de 5 et de 20 secondes. REMARQUE : relcher le bouton aprs le clignotement de 20 secondes. Relcher le bouton. Le dispositif rinitialis revient en mode dintgration automatique, cherchant un rseau ouvert. Le tmoin clignotera lentement en vert pendant que le dispositif cherche un rseau. b. Modle LU04P en rouge/ambre. Enfoncer le bouton pendant 14 secondes. Le tmoin clignotera rapidement Relcher le bouton. Une fois la procdure termine, le dispositif se rinitialisera. Suivre les directives relatives linstallation de ce modle pour savoir comment lintgrer au systme. Nos de catalogue Relais de commutation (LU20S-DNW) 120-277 V c.a., 50/60 Hz 120-277 V c.a., 50/60 Hz Gradation de 0 10 V, absorption de 50 mA Gradateur coupure de phase

(LU107-DNW)

(LU04P-1NW) 120 V c.a., 60 Hz Tension/frquence dentre Courant dentre FICHE TECHNIQUE 120V 277V Au repos : 0,2 W Au repos : 0,3 W Maximal : 0,5 W + courant de charge Maximal : 0,5 W + courant de charge Maximal : 1,2 W + courant de charge Au repos : 0,2 W Au repos : 1,0 W Maximal : 0,6 W + courant de charge Maximal : 0,6 W + courant de charge Au repos : 0,3 W Non pris en charge 20A 10A 10A 10A 10A 6,67 A 6,67 A 1/4 ch (5,8 APC) 1/3 ch (3,0 APC) Charges nominales Usage gnral 120 V DEL, LFC et ballasts lectroniques 120 V DEL, LFC et ballasts lectroniques 277 V Ballasts Mark 10MD 120 V Ballasts magntiques 120 V Ballasts magntiques 277 V Charges rsistives au tungstne 120 V Charges rsistives au tungstne 277 V Moteurs 120 V Moteurs 277V Cote dtanchit Connexions rseau Temprature de fonctionnement Temprature de rangement Utilisation :

Type daction Degr de pollution Impulsions de tension :

Non pris en charge Non pris en charge Non pris en charge Non pris en charge Non pris en charge 360W 800VA 800W 800W Non pris en charge Non pris en charge Non pris en charge Non pris en charge 8A 5A 10A 10A 6,67 A 6,67 A 1 2 1/4 ch (5,8 APC) 1/3 ch (3,0 APC) IP30 0 50 C (32 122 F)

-40 85 C (-40 185 F) commande de fonctionnement IEEE 802.15.4, 2,4 GHz, rseau maill sans fil avec des distances maximales de 75 pi (22,9 m) entre dispositifs 4000V 4000V 2500V nonc de mise en garde Toute modification apporte sans lautorisation expresse de Leviton Manufacturing Co. aura pour effet dannuler les droits dutilisation des produits dcrits aux prsentes. Dclaration de conformit aux exigences de la FCC Les produits dcrits aux prsentes ont fait lobjet de tests et ont t jugs conformes aux normes en matire de dispositifs numriques de classe B, en vertu de la partie 15 des rglements de la FCC. Ces normes ont t labores dans le but dassurer une protection raisonnable contre le brouillage prjudiciable quand lquipement est utilis en milieu rsidentiel. Ces produits gnrent, utilisent et peuvent irradier de lnergie haute frquence; sils ne sont pas installs et utiliss conformment aux directives, ils peuvent engendrer des perturbations susceptibles de brouiller les radiocommunications. Il est cependant impossible de garantir labsence de telles perturbations dans une installation donne. Si ces produits sont des sources de parasites au niveau des rcepteurs radio ou des tlviseurs, ce quon peut dterminer en les mettant sous et hors tension, on recommande lutilisateur de rectifier la situation en adoptant une ou plusieurs des mesures suivantes :

- rorienter ou dplacer lantenne rceptrice;

- augmenter la distance entre les produits et les rcepteurs;

- brancher les produits une prise sur un circuit autre que celui o sont branchs les rcepteurs;

- consulter le dtaillant ou un technicien expriment en matire de radios ou de tlviseurs. Dclaration de conformit aux exigences dIndustrie Canada (IC) Les produits dcrits aux prsentes sont conformes aux CNR dIndustrie Canada applicables aux appareils radio exempts de licence. Leur utilisation est autorise aux deux conditions suivantes : (1) ils ne doivent pas produire de brouillage, et (2) leurs utilisateurs doivent accepter tout brouillage subi, mme si ce dernier est susceptible den compromettre le fonctionnement. AVIS RELATIF AUX MARQUES Lutilisation ici de marques de commerce ou de service, dappellations commerciales ou encore de noms de produits dentreprises tierces nest qu titre informatif; leur intgration aux prsentes ne saurait tre interprte comme un tmoignage daffiliation, de parrainage ou dappui envers leurs propritaires respectifs. Lumina est une marque dpose de Leviton Manufacturing Co., Inc. Bluetooth est une marque de commerce de Bluetooth SIG. Android est une marque dpose de Google LLC. iOS est une marque de commerce de Cisco. Mark 10 est une marque dpose dAdvance Transformer Co. VOISINAGE ET EXPOSITION AUX RADIOFRQUENCES Afin de se conformer aux exigences de la FCC et de respecter les seuils dexposition aux radiofrquences prescrits par lISDE pour le grand public (environnements non contrls), le dispositif dcrit aux prsentes devrait tre install et utilis une distance minimale de 7,9 po (20 cm) de toute personne. Les produits dcrits aux prsentes ne doivent tre ni installs ni utiliss prs dautres antennes ou transmetteurs. GARANTIE LIMITE DE 5 ANS ET EXCLUSIONS Leviton garantit au premier acheteur, et uniquement au crdit du dit acheteur, que ce produit ne prsente ni dfauts de fabrication ni dfauts de matriaux au moment de sa vente par Leviton, et nen prsentera pas tant quil est utilis de faon normale et adquate, pendant une priode de 5 ans suivant la date dachat. La seule obligation de Leviton sera de corriger les dits dfauts en rparant ou en remplaant le produit dfectueux si ce dernier est retourn port pay, accompagn dune preuve de la date dachat, avant la fin de la dite priode de 5 ans, la Manufacture Leviton du Canada S.R.I., au soin du service de lAssurance Qualit, 165 boul. Hymus, Pointe-Claire, (Qubec), Canada H9R 1E9. Par cette garantie, Leviton exclut et dcline toute responsabilit envers les frais de main doeuvre encourus pour retirer et rinstaller le produit. Cette garantie sera nulle et non avenue si le produit est install incorrectement ou dans un environnement inadquat, sil a t surcharg, incorrectement utilis, ouvert, employ de faon abusive ou modifi de quelle que manire que ce soit, ou sil na t utilis ni dans des conditions normales ni conformment aux directives ou tiquettes qui laccompagnent. Aucune autre garantie, explicite ou implicite, y compris celle de qualit marchande et de conformit au besoin, nest donne, mais si une garantie implicite est requise en vertu de lois applicables, la dite garantie implicite, y compris la garantie de qualit marchande et de conformit au besoin, est limite une dure de 5 ans. Leviton dcline toute responsabilit envers les dommages indirects, particuliers ou conscutifs, incluant, sans restriction, la perte dusage dquipement, la perte de ventes ou les manques gagner, et tout dommage-intrt dcoulant du dlai ou du dfaut de lexcution des obligations de cette garantie. Seuls les recours stipuls dans les prsentes, quils soient dordre contractuel, dlictuel ou autre, sont offerts en vertu de cette garantie. 2019 Leviton Mfg. Co., Inc. Ligne dAssistance Technique : 1-800-405-5320 (Canada seulement) www.leviton.com PK-A3314-10-05-2A-X3 ARTWORK PRINT SPECIFICATIONS PART NUMBER PK-A3314-10-05-2A-X3 REV DESCRIPTION Instruction Sheet Artwork must be printed at 100% (1:1 scale) Color(s):

1 over 1 Fonts:

Helvetica Black x Spot CMYK For manuals - designates cover specifications Fold Line Kiss Cut Cellophane Glue Die Line Key:

Die Cut Perforate MANUAL INTERIORS / BINDERY / FOLD SCHEME :

Color(s):

over Fonts:

1:

2:

3:

4:

1:

2:

3:

4:

Spot CMYK 1:

2:

3:

4:

1:

2:

3:

4:

Die cut x Fold Saddle Stitch Perfect Bind Drill Trim DIMENSIONS / FOLD SCHEME / BINDERY DIAGRAM 8.5"

Part No. 11"

2.125"

2.75"

Part No. Die Cut Fold Line Punch/Drill Hole SPECIFICATIONS :

Thickness:

40 lb. Material:

Finish:

Body Material:

Thickness:

Bindery PROCESS :

x Offset Flexo Other Line Screen:

Angle:

Resolution:

COMMENTS :

The information in this document is the exclusive PROPRIETARY property of LEVITON MANUFACTURING COMPANY, INC. It is disclosed with the understanding that acceptance or review by the recipient constitutes an undertaking by the recipient. (1) to hold this information in strict confidence, and (2) not to disclose, duplicate, copy, modify or use the information for any purpose other than that for which disclosed. FOR LEVITON USE ONLY Approvals:

x Plant 08 J. Tang cc: H. Cai Mktg Cust CQA x x Eng R. Brown Other M. Blonder A. Rogowicz cc: R. Parks, L. Pukhrambam PM S & A x x x D. Moskovkin cc: F. Tse Other V. LoNigro PN-ARN:

EM0301-6268 ECR Number:

Pilot Rev:

X3 Released Artwork Format: Production PDF Artwork Release Date:

Artist:

L. Walsh Notes:

Artwork Print Specification Sheet Rev A12.eps

Photosonlyforlabelplacementpurposes,refertofollowingpagesforlabeldrawings B B B LEVITON PART NO.: 0XB5300xx0101 ASSEMBLED IN MEXICO

- FOR FUTURE USE -

LEVITON PART NO.: 0XB5300xx0108 MADE IN CHINA LEVITON PART NO.: 0XB5300xx0148 ASSEMBLED IN USA

- FOR FUTURE USE -

B NOTES (UNLESS OTHERWISE SPECIFIED):

1. MATERIAL AND DIMENSIONS SPECIFIED ON DRAWING OXB5300-D01. 2. PRINT BLACK CHARACTERS AND GRAPHICS ON WHITE BACKGROUND PER ARTWORK ORB5300-D01revB.ai (FOR PURCHASED, "xx" IN PART NO.

= 89) OR .jpg (FOR SELF-PRINT, "xx" IN PART NO. = 00). GRAPHICS SHOWN FOR ILLUSTRATION PURPOSES ONLY. STATUS:

Production Release REV. DATE ECO NUMBER CHGD APVD B A

06/10/2019 ECR18680 12/14/2018 ECR17502

RJ RJ

RJ YA

The information in this document is the exclusive PROPRIETARY property of LEVITON MFG. CO., INC. It is disclosed with the understanding that acceptance or review by the recipient constitutes an undertaking by the recipient:

(1) to hold this information in strict confidence.

(2) not to disclose, duplicate, copy, or use the information, in whole or in part, for any purpose other than that for which disclosed. UNLESS OTHERWISE SPECIFIED:

DO NOT SCALE DRAWING. ALL DIMENSIONS ARE IN MILLIMETERS. ALL ANGLES ARE IN DEGREES. TITLE:

TOLERANCES LABEL PROD ID 802.15.4 0-10V DIMMER INCH

.XX

.XXX

.01

.005 METRIC

.2 mm

.10 mm

.X

.XX DWN BY CHK BY RJ NR 09/22/2017 ENGRG YA 12/14/2018 12/14/2018 MFG NR 12/14/2018 ANGLES:

1/2 DWG NO. THIRD ANGLE PROJECTION ORB5300-D01 Copyright 2010. Unpublished. All Rights Reserved. ALL PRINTED COPIES ARE UNCONTROLLED SIZE A PROJECT NO. PROJ-03163 SCALE:2:1 SHEET 1 OF 1 REV B B B B LEVITON PART NO.: 0XB5302xx0101 ASSEMBLED IN MEXICO

- FOR FUTURE USE -

LEVITON PART NO.: 0XB5302xx0108 MADE IN CHINA LEVITON PART NO.: 0XB5302xx0148 ASSEMBLED IN USA

- FOR FUTURE USE -

B NOTES (UNLESS OTHERWISE SPECIFIED):

1. MATERIAL AND DIMENSIONS SPECIFIED ON DRAWING OXB5300-D01. 2. PRINT BLACK CHARACTERS AND GRAPHICS ON WHITE BACKGROUND PER ARTWORK ORB5302-D01revB.ai (FOR PURCHASED, "xx" IN PART NO.

= 89) OR .jpg (FOR SELF-PRINT, "xx" IN PART NO. = 00). GRAPHICS SHOWN FOR ILLUSTRATION PURPOSES ONLY. STATUS:

Production Release REV. DATE ECO NUMBER CHGD APVD B A

06/10/2019 ECR18680 12/14/2018 ECR17502

RJ RJ

RJ YA

The information in this document is the exclusive PROPRIETARY property of LEVITON MFG. CO., INC. It is disclosed with the understanding that acceptance or review by the recipient constitutes an undertaking by the recipient:

(1) to hold this information in strict confidence.

(2) not to disclose, duplicate, copy, or use the information, in whole or in part, for any purpose other than that for which disclosed. UNLESS OTHERWISE SPECIFIED:

DO NOT SCALE DRAWING. ALL DIMENSIONS ARE IN MILLIMETERS. ALL ANGLES ARE IN DEGREES. TITLE:

TOLERANCES LABEL PROD ID 802.15.4 0-10V DIMMER 347V INCH

.XX

.XXX

.01

.005 METRIC

.2 mm

.10 mm

.X

.XX DWN BY CHK BY RJ NR 09/22/2017 ENGRG YA 12/14/2018 12/14/2018 MFG NR 12/14/2018 ANGLES:

1/2 DWG NO. THIRD ANGLE PROJECTION ORB5302-D01 Copyright 2010. Unpublished. All Rights Reserved. ALL PRINTED COPIES ARE UNCONTROLLED SIZE A PROJECT NO. PROJ-03163 SCALE:2:1 SHEET 1 OF 1 REV B NOTES (UNLESS OTHERWISE SPECIFIED):

1. USE ARTWORK MODEL ORB8381-M01. 2. GRAPHICS SHOWN FOR ILLUSTRATION PURPOSES ONLY. 3. GRAPHICS TO BE LASER ENGRAVED IN LASER PRINTING MACHINE USING PARAMETERS IN TABLE BELOW. THIS SETUP WILL ETCH THE GRAPHICS ON THE PLASTIC AT THE PROPER COLOR TONE.

(parameters TBD during Eng Run) REV. DATE ECO NUMBER CHGD APVD STATUS:

In Work 1

UNLESS OTHERWISE SPECIFIED:

DO NOT SCALE DRAWING. ALL DIMENSIONS ARE IN MILLIMETERS. ALL ANGLES ARE IN DEGREES. TITLE:

The information in this document is the exclusive PROPRIETARY property of LEVITON MFG. CO., INC. It is disclosed with the understanding that acceptance or review by the recipient constitutes an undertaking by the recipient:

(1) to hold this information in strict confidence.

(2) not to disclose, duplicate, copy, or use the information, in whole or in part, for any purpose other than that for which disclosed. TOLERANCES INCH

.XX

.XXX

.01

.005 METRIC

.2 mm

.10 mm

.X

.XX ANGLES:

1/2 THIRD ANGLE PROJECTION Copyright 2010. Unpublished. All Rights Reserved. ALL PRINTED COPIES ARE UNCONTROLLED

ART - LASER ETCH LU107 LUMINA RF ZONE CONTROL DWN BY RJ 07/12/2019 ENGRG

MFG

CHK BY

DWG NO. ORB8381-D01 SIZE A PROJECT NO. PROJ-03357 SCALE:2:1 SHEET 1 OF 1 REV 1

LEVITON PART NUMBER (Global) 0XB1347890000 MANUFACTURER NAME MANUFACTURER PART NUMBER JOHANSON TECHNOLOGY 2450AT18D0100E NOTES:

1. 2. 3. SINGLE SOURCE: ALL ALTERNATES MUST HAVE ENGINEERING APPROVAL SEE FOLLOWING PAGES FOR PURCHASING INFO FROM DATA SHEET ITEM MUST BE ROHS COMPLIANT MANUFACTURING PART NUMBER EXPLANATION:

SEE MANUFACTURER DATA SHEET FOR DETAILS NOTE: As of 09/23/2013 all new parts created to unified P/N system REV. DATE ECO NUMBER CHGD APVD A 02/22/2016 0000000 NRD RY7

l e s a e e R n o i t c u d o r P

S U T A T S UNLESS OTHERWISE SPECIFIED:

DO NOT SCALE DRAWING. ALL DIMENSIONS ARE IN INCHES. ALL ANGLES ARE IN DEGREES. TITLE:

TOLERANCES IC ANTENNA 2.45GHz DETUNE RESILIENT SMD INCH METRIC DWN BY NRD 02/22/2016 ENGRG RY7 02/22/2016

.XX

.XXX

.01

.005

.X

.XX

.2 mm

.1 mm CHK BY RY7 02/22/2016 MFG RY7 02/22/2016

(1) to hold this information in strict ANGLES:

1/2 DWG NO. THIRD ANGLE PROJECTION OXB1347-D01 Copyright 2009. Unpublished. All Rights Reserved. ALL PRINTED COPIES ARE UNCONTROLLED SIZE A PROJECT NO. 02636 SCALE:1:1 SHEET 1 OF 7 REV A The information in this document is the exclusive PROPRIETARY property of LEVITON MFG. CO., INC. It is disclosed with the understanding that acceptance or review by the recipient constitutes an undertaking by the recipient:

confidence.

(2) not to disclose, duplicate, copy, or use the information, in whole or in part, for any purpose other than that for which disclosed.

"High Frequency Ceramic Solutions"

9/17/2015 2.45 GHz SMD Antenna, EIA 1210, Detuning resilient, Edge Mount Design Detail Specification:

This antenna is optimal for edge middle mounting; rectangular and circular PCB shape applications, go to pages 2-4 for more info. General Specifications Part Number Frequency (MHz) Peak Gain Average Gain Return Loss Operating Temperature Input/Output Power Impedance Reel Quantity Storage Temp Total Radiation Efficiency1 1Efficiency measured on 2450AT18D0100-EB1SMA 40x20mm EVB on page 2 1.5 dBi typ. (XZ-total)

-1.0 dBi typ. (XZ-total) 10.0 dB min.

-40 to +125C 2450AT18D0100 2W max. (CW) 50 3,000

-40 to +85C 2400 - 2500 72%

P/N 2450AT18D0100 Page 1 of 6 No. 1 2 Terminal Function Feeding Point GND 3 4 GND GND 4 1 Mechanical Specifications L W T a b 0.126 0.063 0.047 0.012 0.020 In 0.008 0.008 0.008

.004/-.008 0.008 mm 3.20 1.60 1.20 0.30 0.50 0.20 0.20 0.20 0.1/-0.2 0.20 b a L 3 2 w Need help designing the antenna in? Use our antenna design services! www.johansontechnology.com/ipcantennaservices 2 Free layout reviews and if you need us to tune and characterize our antenna on your design (anechoic chamber) we can do that too (lab fee may apply for the latter). Mounting Considerations 1: Standard Rectangular Layout Mount these devices with the red square mark facing up. Otherwise, the antenna will not operate as intended. 1.0 2.0 1.0 b T 0.6 0.7 0.6 4.1 Ground 6.0 Solder Resist Ground Land 0 Ohm 50 Trace (Grounded CPWG type is preferred) GND Vias Want the layout file of this? Send us a message at:

Ground www.johansontechnology.com/ask-a-question 4.0 No ground, metal PCB layers, or other metallic components like batteries directly underneath antenna!

Matching Circuits2 2It is recommended that the designer leave available slots for a "pi" (or shunt-series-shunt) network, even if all slots won't be used, this will prepare the PCB for the final mass production values of the matching circuit. The antenna matching network values above are used when antenna is mounted on Johanson's evaluation board. The matching values on clients PCB will be different. Go to:

http://johansontechnology.com/tuning and see how to obtain the new values yourself if you have a network analyzer. www.johansontechnology.com 4001 Calle Tecate Camarillo, CA 93012 TEL 805.389.1166 FAX 805.389.1821 Ver 3.0 2015 Johanson Technology, Inc. All Rights Reserved

"High Frequency Ceramic Solutions"

2.45 GHz SMD Antenna, EIA 1210, Detuning resilient, Edge Mount Design Detail Specification: 04/04/12 This antenna is optimal for edge middle mounting; rectangular and circular PCB shape applications, go to pages 2-4 for more info. Mounting Considerations 1: Standard Rectangular Layout (continued) P/N 2450AT18D0100 Page 2 of 6 Matching Circuits Via

) 6.0 No 4.0 20mm Feeding Line Measured total radiated efficiency of 2450AT18D0100 on this EVB: 72%

Ground Vias (put these all around your PCB, they will increase the antenna's 40mm Orderable EVB p/n (comes with 1 female SMA connector mounted on the opposite side):

2450AT18D0100-EB1SMA We offer 2 free layout reviews as well as antenna tuning and characterization services (lab fee may apply). For more info go to:

www.johansontechnology.com/ipcantennaservice Want the layout file of the above? Send us a message at: www.johansontechnology.com/ask-a-question To order a pre-tuned 50 EVB with a female SMA connector you see above Click here:

www.johansontechnology.com/request-a-sample Reference p/n: 2450AT18D0100-EB1SMA Mounting Considerations 2: Small clearance or "thin edge" applications Solder Resist Reserve for Pi-matching circuit3 1.0 2.0 1.0 Land

Units in mm 0.6 2.8 3.4 Ground 0.6 0.7 0.6 8.0 Blue Area = LCD/Metal/CAN/GND/Battery etc. No ground or metals in yellow area and must be located somewhere in the middle of the assembly, not the corner Want the layout file of this example? Send us a message at:

3It is recommended that the designer leave available slots for a "pi" (or shunt-series-

shunt) network, even if all slots won't be used, this will prepare the PCB for the unpredictable final mass production version of the matching circuit. The antenna matching network values above are used when antenna is mounted on Johanson's evaluation board. The matching values on clients PCB will be different. 0.6 3.4 1.5 www.johansontechnology.com/ask-a-question Note: There's no orderable EVB available for the above reference "Mounting Considerations 2" reference design Johanson Technology, Inc. reserves the right to make design changes without notice. Please confirm the specifications and delivery conditions when placing your order. All sales are subject to Johanson Technology, Inc. terms and conditions. www.johansontechnology.com 4001 Calle Tecate Camarillo, CA 93012 TEL 805.389.1166 FAX 805.389.1821 Ver 3.0 2015 Johanson Technology, Inc. All Rights Reserved

"High Frequency Ceramic Solutions"

2.45 GHz SMD Antenna, EIA 1210, Detuning resilient, Edge Mount Design Detail Specification: 04/04/12 This antenna is optimal for edge middle mounting; rectangular and circular PCB shape applications, go to pages 2-4 for more info. Mounting Considerations 3: Thin Edge + Circular PCB applications P/N 2450AT18D0100 Page 3 of 6 50 Trace (Grounded CPWG type is preferred) Want the layout file of this example? Send us a message at:

www.johansontechnology.com/ask-a-question Ground No ground, metal PCB layers, or other metallic components like batteries and displays directly underneath antenna!

Note: There's no orderable EVB available for the above reference "Mounting Considerations 3" reference design Mounting Considerations 4: Chip antenna fed from the right

) Ground Plane Matching Circuits: It is recommended that the designer leave available slots for a "pi" (or shunt-

series-shunt) network, even if all slots won't be used, this will prepare the PCB for the final mass production values of the antenna matching securing Note: There's no orderable EVB available for the above reference "Mounting Considerations 4" reference design Johanson Technology, Inc. reserves the right to make design changes without notice. Please confirm the specifications and delivery conditions when placing your order. All sales are subject to Johanson Technology, Inc. terms and conditions. www.johansontechnology.com 4001 Calle Tecate Camarillo, CA 93012 TEL 805.389.1166 FAX 805.389.1821 Ver 3.0 2015 Johanson Technology, Inc. All Rights Reserved

"High Frequency Ceramic Solutions"

2.45 GHz SMD Antenna, EIA 1210, Detuning resilient, Edge Mount Design Detail Specification: 04/04/12 This antenna is optimal for edge middle mounting; rectangular and circular PCB shape applications, go to pages 2-4 for more info. Typical Return Loss (S11) Electrical Performance (T=25C) P/N 2450AT18D0100 Page 3 of 5 0

) 1

, 1

S

B d

-10

-20

-30 2.0 2.400GHz m1 freq=

dB(S(1,1))=-13.935 m2 freq=

dB(S(1,1))=-14.774 2.500GHz m3 freq=

dB(S(1,1))=-24.894 2.450GHz m1 m2 m3 2.2 2.4 2.6 2.8 3.0 freq, GHz Johanson Technology, Inc. reserves the right to make design changes without notice. Please confirm the specifications and delivery conditions when placing your order. All sales are subject to Johanson Technology, Inc. terms and conditions. www.johansontechnology.com 4001 Calle Tecate Camarillo, CA 93012 TEL 805.389.1166 FAX 805.389.1821 Ver 3.0 2015 Johanson Technology, Inc. All Rights Reserved

"High Frequency Ceramic Solutions"

2.45 GHz SMD Antenna, EIA 1210, Detuning resilient, Edge Mount Design Detail Specification:

This antenna is optimal for edge middle mounting; rectangular and circular PCB shape applications, go to pages 2-4 for more info. Typical EM Radiation Performance (T=25C) 9/17/2015 P/N 2450AT18D0100 Page 4 of 5 TypicalRadiationPatterns XY-V/XY-H Z 180 XY cut @2.45GHz Vertical Horizontal 90 90 90 2450AT18D0100-EB1SMA Evaluation Board as AUT for all 3 scans Y 0 XY-cut scanning direction XZ-V/XZ-H Y XZ cut @2.45GHz Vertical Horizontal 180 Z 0 XZ-cut scanning direction YZ-V/YZ-H X 180

) YZ cut @2.45GHz Vertical Horizontal Z 0 YZ-cut scanning direction X 270 X 270 Y 270 Johanson Technology, Inc. reserves the right to make design changes without notice. Please confirm the specifications and delivery conditions when placing your order. All sales are subject to Johanson Technology, Inc. terms and conditions. www.johansontechnology.com 4001 Calle Tecate Camarillo, CA 93012 TEL 805.389.1166 FAX 805.389.1821 Ver 3.0 2015 Johanson Technology, Inc. All Rights Reserved

"High Frequency Ceramic Solutions"

2.45 GHz SMD Antenna, EIA 1210, Detuning resilient, Edge Mount Design Detail Specification:

This antenna is optimal for edge middle mounting; rectangular and circular PCB shape applications, go to pages 2-4 for more info. Part Number Explanation 9/17/2015 P/N 2450AT18D0100 Page 5 of 5 P/N Suffix Packing Style EVB p/n Recommended Storage Conditions of uninstalled product still on T&R Bulk T & R 2450AT18D0100-EB1SMA Suffix = S Suffix = E eg.2450AT18D0100S e.g.. 2450AT18D0100E

+5 ~ +35 C, Humidity 45~75%RH, 18 mos. Max Antenna layout review, tuning, and characterization services www.johansontechnology.com/ipcantennaservices More SMD Chip Antennas at:

www.johansontechnology.com/antennas Soldering Information www.johansontechnology.com/ipcsoldering-profile Antenna layout and tuning techniques (How to obtain the new antenna matching values) www.johansontechnology.com/tuning Packaging information RoHS Compliance MSL Info www.johansontechnology.com/ipcpackaging.html www.johansontechnology.com/technical-notes/rohs-compliance.html www.johansontechnology.com/technical-notes/msl-rating.html P/N Explanation and Breakdown www.johansontechnology.com/ipc-pn-explained Johanson Technology, Inc. reserves the right to make design changes without notice. Please confirm the specifications and delivery conditions when placing your order. All sales are subject to Johanson Technology, Inc. terms and conditions. TechnicalAuthor:ManuelCarmona www.johansontechnology.com 4001 Calle Tecate Camarillo, CA 93012 TEL 805.389.1166 FAX 805.389.1821 Ver 3.0 2015 Johanson Technology, Inc. All Rights Reserved

Authority to Act as Agent Date: October 18, 2019 American Certification Body, Inc. 6731 Whittier Avenue Suite C110 McLean, VA 22101 To Whom It May Concern:

Ryan Urness and Amanda Hauck of Laird Connectivity, LLC are authorized to act on our behalf, until otherwise notified, for applications to American Certification Body, Inc. (ACB). We certify that we are not subject to denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. Further, no party, as defined in 47 CFR 1.2002 (b), to the application is subject to denial of federal benefits, that includes FCC benefits. We also declare that the information provided to the FCC is true and correct to the best of our knowledge (47 CFR 2.911(d)) and we have been informed of the grantee responsibilities (47 CFR 2.909) with regard to certified equipment. SU e vein Agency Agreement Expiration Date: 10/17/2020 aan sha vA gi Pa = lariat ite

; (Signature) (Print name) Title: Director, Codes, Standards & Compliance On behalf of: _ Leviton Manufacturing Co., Inc.

(Company Name) Telephone: 631-812-6437 Leviton Manufacturing Co., Inc. Energy Management, Controls and Automation (EMC&A) vA0L om S Soe tLe T: 503-404-5500 Tualatin, OR 97062-8812 www.leviton.com

Date: 07/09/19 LEVITON Subject: Confidentiality Request for: FCC ID: QGH-B167601 and IC: 2473A-B167601 FCC ID: QGH-B167602 and IC: 2473A-B167602 Pursuant to FCC 47 CFR 0.457(d) and 0.459 and IC RSP-100, Section 9.4, the applicant requests that a part of the subject FCC application be held confidential. _ Type of Confidentiality Requested Exhibit C Short Term Permanent Block Diagrams

& Short Term External Photos

& Short Term C] Permanent *! Internal Photos CO Short Term & Permanent Operation Description/Theory of Operation

(J Short Term C) Permanent Parts List & Placement/BOM C) Short Term C) Permanent Tune-Up Procedure

( Short Term & Permanent Schematics

{&) Short Term Test Setup Photos

& Short Term ( Permanent * Users Manual Leviton Manufacturing Co. Inc. has spent substantial effort in developing this product and it is one of the first of its kind in industry, Having the subject information easily available to "competition" would negate the advantage they have achieved by developing this product. Not protecting the details of the design will result in financial hardship, Permanent Confidentiality:

The applicant requests the exhibits listed above as permanently confidential be permanently withheld from public review due to materials that contain trade secrets and proprietary information not customarily released to the public. Short-Term Confidentiality:

The applicant requests the exhibits selected above as short term confidential be withheld from public view for a period of 180 (specify number of days not to exceed 180) days from the date of the Grant of Equipment Authorization and prior to marketing, This is to avoid premature release of sensitive information prior t marketing or release of the product to the public. Applicant is also aware that they are responsible to notify ACB in the event information regarding the product or the product is made available to the public before the requested period has expired. ACB will then release the documents listed above for public disclosure pursuant to FCC Public Notice DA 04-1705. NOTE for Industry Canada Applications:

IC currently only distinguishes Permanent Confidentiality exhibits as shown above, Short Term confidentiality is not considered applicable to IC applications. Sincerely, _ Fro ee ___Frank Tse sre Se Wlgniiensiocems Codes, Standards and Compliance *) (Print name)

- The asterisked items (*) require further information to be provided to ACB before permanent confidentiality will be extended to nam cubits. Please refer to Foe KD Tan and the specific Document link for DOl found at:

spevitie ne ena that must accompany these enna, a

? - Please refer to http://a complete details.

- Must be signed by applicant contact given for applicant on the FCC site, or by the authorized agent if an appropriate authorized agent letter has been provided. Letters should be placed on appropriate letterhead. Leviton Manufacturing Co., Inc. Energy Management, Controls and Automation (EMC&A) 20497 SW Teton Avenue Tualatin, OR $7062 T: $03-404-5500 www.leviton.com

Frank Tse Director Codes Standards & Compliance March 6, 2020 Cover Letter for FCC Application Please grant FCC certification for the Lumina RF Wall Switch family with Dimmer as described below. These 3 products utilize the 2.4GHz Zigbee protocol to work with other Zigbee products networked to the wall station. All models share same power PCB B1674 and logic PCB B1676 with different assembly variants to support functions as required. Each wall station utilizes a 2.4 GHz Zigbee radio that is integrated into the logic board B1676. Assembly differences of B1676 are as below:

- There is no difference in radio MCU or components or antenna tuning values in all variants.

- Variant D21 is same as used for variant D01 except dimming LEDs and switches and only one switch. The power board B1674 for each wall station differs on the input voltage range that it is compatible. Variant D01 supports 120-277VAC while variant D02 supports 347VAC. Preliminary testing on all variations of power and logic boards demonstrated that the RF specifications and performance are similar across all models and can be considered for a family approval under a single FCC ID for FCC. The table below shows the features for each model. FCC ID#

Description Radio Switch PCB Variant Assembly Difference Configuration 0-10 Vdc Dimming Logic PCB Power PCB Power PCB Variant Input Voltage Loads Relay Rating QGH-B167601 LU107-DNW Zigbee Yes Yes B1676 D01 D21 D01

D01 with no dimming LEDs and switches B1674 D01 120-

277VAC D02 347VAC 5A Electronic 5A Fluorescent 10A Tungsten 5A Electronic 5A Fluorescent 10A Tungsten 5A/

10A 5A/

10A Product ID Model# /

Cat#

ZS057-D0Z Lumina 0-10VDC RF Wall Dimmer Lumina RF Wireless Load Control 0-10V Dimmer Lumina RF Wall Switch ZS057-30Z w/0-10V Dimmer, 347Vac Sincerely, Frank Tse Leviton Manufacturing Co., Inc. 201 North Service Road Melville, NY 11747 T: (631) 812-6437 www.leviton.com Page 1 of 1