ATC5CPL004 User Manual Description
- Model : ATC5CPL004
- WLAN : 802.11 a/b/g/n/ac
- Frequency Range : 2400MHz ~ 5845MHz Features
- Dimension : 22.5mm x 20.0mm x 2.9mm
- Temperature Range : -40 ~ +85
- Supply Voltage : VBAT 3.2V to 3.6V
- Output Power WLAN : 12.0dBm(11b 11Mbps), 12dBm(11g 54Mbps, 11n 2.4G MCS7), 8dBm(11a 54Mbps), 8dBm(11n 5G MCS7), 8dBm(11ac MCS9)
- Interface : PCIe(WLAN) Application
- Automotive (Outdoor Device) Dimensions Copyright. 2019. All Rights Reserved. 1/13 15.591719.217.713.54.55.52.53.51.21.20.450.90.90.915.7183.94.050.30.3+0.0- 0.33.1 ATC5CPL004 User Manual Operating condition 1) Recommended operation conditions Parameter Operating Temperature Range Supply Voltage : VBATT (3.3V) Supply Voltage : VIO (1.8V to 3.3V) 2) Current consumption Min
-40 3.01) 1.62 Max
+85 3.6 3.6 Parameter Average Stand-by (BT & WLAN) WLAN Continuous Rx WLAN Continuous Tx2) Bluetooth Connection 10 180 790 20 Unit V V Unit mA mA mA mA Copyright. 2019. All Rights Reserved. 2/13 ATC5CPL004 User Manual Boot up sequence Min 10msec Max12.4msec Min21.4msec e Copyright. 2019. All Rights Reserved. 3/13 ATC5CPL004 User Manual General Features BT(V5.1) + 2.4GHz/5GHz Wi-Fi 5(802.11a/b/g/n/ac) 2.4G SISO / 5G 2x2 MIMO Module 1) Features Operation Voltage is 3.3V/1.8V Dual Power Rail Up to 866 Mbps data rate(802.11ac wave2 compliant) Automotive Module
- All components are AEC-Q 100/200 qualified Support 2 Antenna port
- ANT0: Bluetooth/WLAN 5GHz, ANT1: WLAN WLAN2.4&5GHz Integrated WLAN PA, LNA (CYW88459) and RF Switch RoHS Compliant Size : 19.2 x 17.0 x 3.1mm Support bandwidth : HT20 / HT40 / VHT80 Interface: PCIe(WLAN), UART, PCM/I2S(BT) Package type : SMD type(LGA) Bluetooth(BT5.1 + EDR compliant) 1) Bluetooth Key Features Support for Bluetooth 5.1 features
- GATT Caching
- Angle of Arrival (AoA) and Angle of Departure (AoD)
- Advertising Channel Index Randomization
- Selective parts of Minor Feature Enhancements batch1 Fully supports Bluetooth 5.0 features:
- LE 2 Mbits/s
- LE Long Range, S2/S8 coding
- LE Higher Output Power
- LE Advertising Extensions
- LE Channel Selection Algorithm #2
- LE High Duty Cycle Non-Connectable Advertising
- Slot Availability Mask (SAM) Fully supports Bluetooth 4.2 features
- LE Data Packet Length Extension
- LE Secure Connections
- Link Layer privacy
- Link Layer Extended Scanner Filter policies Copyright. 2019. All Rights Reserved. 4/13 ATC5CPL004 User Manual General Features Bluetooth(BT5.1 + EDR compliant) Fully supports Bluetooth 4.1 features
- BR/EDR secure connections
- eSCO reserved slots clarification
- Train nudging
- Generalized interlaced scan
- Connectionless Slave broadcast
- Unencrypted unicast connectionless data support
- Low duty cycle directed advertising
- 32-bit UUID support in LE
- LE dual mode topology
- Piconet clock adjustment
- LE L2CAP connection oriented channel support
- LE privacy v1.1
- LE Link Layer topology
- LE ping
- Fast advertising interval HCI UART baud rates up to 4 Mbits/s supporting maximum Bluetooth data rates Multipoint operation with up to seven active slaves
- Maximum of seven simultaneous active ACL links
- Maximum of three simultaneous active SCO and eSCO connections with scatternet support Narrowband and wideband packet loss concealment Scatternet operation with up to four active piconets with background scan and support for scatter mode High-speed HCI UART transport support with low-power out-of-band BT_DEV WAKE and BT_HOST_WAKE signaling Channel quality driven data rate and packet type selection Standard Bluetooth test modes Extended radio and production test mode features Full support for power savings modes
- Bluetooth clock request
- Bluetooth standard sniff
- Deep-sleep modes and software regulator shutdown Copyright. 2019. All Rights Reserved. 5/13 ATC5CPL004 User Manual General Features WLAN 1) WLAN RF band & modulation Features Dual-band 2.4GHz and 5GHz 802.11 a/b/g/n/ac(802.11ac compliant) Dual-stream up to 866Mbps data rate Supports 20, 40 and 80MHz channels with optional SGI(256 QAM modulation) Tx and Rx low-density parity check(LDPC) Supports IEEE 802.11ac/n beamforming Supports two antennas with one dedicated to Bluetooth and WLAN and one to WLAN. PCIe mode complies with PCI Express base specification revision 3.0 for x1 lane and power management running at Gen1 speeds WPA and WPA2(Personal) support for powerful encryption and authentication AES and TKIP in hardware for faster data encryption and IEEE 802.11i compatibility Reference WLAN subsystem provides Wi-Fi protected Setup(WPS) 2) WLAN MAC features Enhanced MAC for supporting IEEE 802.11ac features Transmission and reception of aggregated MPDUs(A-MPDU) for high throughput(HT) Support for power management schemes, including WMM power-save multi-
poll(PSMP) and multiphase PSMP operation Support for immediate ACK and block-ACK policies Inter-frame space timing support, including RIFS Back-off counters in hardware for supporting multiple priorities as specified in the WMM specification Timing synchronization function(TSF), network allocation vector(NAV) maintenance, and target beacon transmission time(TBTT) generation in hardware Hardware offload for AES-CCMP, legacy WPA TKIP, legacy WEP ciphers, WAPI, and support for key management WPA, WAPI STA, and WPA2/WPA3 support for powerful encryption and authentication Programmable independent basic service set(IBSS) or infrastructure basic service set functionality Copyright. 2019. All Rights Reserved. 6/13 ATC5CPL004 User Manual General Features WLAN 3) WLAN PHY features Programmable data rates from MCS0-9 in 20MHz, 40MHz, and 80MHz channels, as specified in IEEE 802.11ac Improved performance with 2x2 channel smoothing and spur canceller support Supports Optional short GI and Green field modes in Tx and Rx Tx and Rx LDPC for improved range and power efficiency Beamforming support Supports IEEE 802.11h/k for worldwide operation Advanced algorithms for low power, enhanced sensitivity, range, and reliability IEEE 802.11a, 11b, 11g, 11n, 11ac single stream PHY standards Designed to meet FCC and other worldwide regulatory requirements Copyright. 2019. All Rights Reserved. 7/13 ATC5CPL004 User Manual Pin Configuration Copyright. 2019. All Rights Reserved. 8/13 ATC5CPL004 User Manual Pin Configuration No Pin Name I/O Description 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 BT_UART_RXD BT_UART_TXD BT_PCM_SYNC BT_PCM_CLK BT_PCM_IN BT_PCM_OUT GND PCIE_PERST_N PCIE_PME_L I/O Bluetooth UART signal input I/O Bluetooth UART signal output I/O PCM sync signal, can be master (output) or slave (input) I/O PCM clock, can be master (output) or slave (input) I PCM data input O PCM data output
I Ground PCIE system reset. O PCIE power management event output PCIE_CLKREQ_N O PCIE clock request signal PCIE_CLK_N PCIE_CLK_P PCIE_TD_N PCIE_TD_P PCIE_RD_N PCIE_RD_P PCIE_EN WL_DEV_WAKE BT_DEV_WAKE SDIO_DIS SDIO_DATA3 SDIO_DATA2 SDIO_CLK SDIO_PAD SDIO_DATA1 SDIO_DATA0 SDIO_CMD GND CO_EX_OUT1 CO_EX_OUT0 I I PCIE differential clock input negative PCIE differential clock input positive O PCIE Transmitter differential negative O PCIE Transmitter differential positive I I I PCIE Receiver differential negative PCIE Receiver differential positive PCIE_ENABLE
: Low : PCIE Disabled, High : PCIE Enabled I WLAN device wake from host I I Bluetooth device wake from host SDIO_DISABLE
: For use of PCIe High I/O SDIO data line 3 I/O SDIO data line 2 I I SDIO clock SDIO_PADVDDIO
: For use of PCIe High I/O SDIO data line 1 I/O SDIO data line 0 I/O SDIO command line
Ground O 3-Wire Co-Existence Out1 O 3-Wire Co-Existence Out0 Copyright. 2019. All Rights Reserved. 9/13 ATC5CPL004 User Manual Pin Configuration No 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 Pin Name CO_EX_IN BT_RST_N GND VBAT GND Version Pin VIO GND NC GND WL_REG_ON BT_REG_ON LPO WL_HOST_WAKE BT_HOST_WAKE GND GND ANT_CORE0 GND ANT_CORE1 GND GND BT_UART_CTS_N BT_UART_RTS_N GND GND GND GND GND GND GND GND I/O Description I I
I
I
I I 3-Wire Co-Existence In Bluetooth Reset
- Active-low reset input Ground Positive supply
- Supply voltage : Typical 3.3V. Ground Ground BT, WLAN VDDIO supply voltage.(3.3V or 1.8V)
- BT and WLAN should be same power rail Ground Floating Ground WLAN Power on reset
- Internal 200K pull-down BT Power on Reset Low power clock input (32.768KHz, 200~1800mV P-P) I O WLAN host wake from device O Bluetooth host wake from device
Ground Ground
I/O WLAN 5G RF with Bluetooth RF ANT
Ground I/O WLAN 2.4G, 5G RF ANT Ground Ground
I/O Bluetooth UART clear to send I/O Bluetooth UART request to send
Ground Ground Ground Ground Ground Ground Ground Ground Copyright. 2019. All Rights Reserved. 10/13 ATC5CPL004 User Manual Module Integration Guide 1. Applicable FCC Rules
- CFR 47 Part 15.247 2. Operational Condition The module is limited to OEM installation ONLY. The OEM integrator is responsible for ensuring that the end-user has no manual instruction to removeor install module. 3. Limited Module Procedure ATC5CPL004 is limited Module. The module doesn't have its own power supply regulation. Therefore, the host product manufacturer must design the host product so that a constant voltage of 3.3V is applied to the module. 4. Trace antenna desings : N/A 5. RF Exposure consideration (CFR 47 Part 1, 1.1307(b), 1.1310) This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum 20 cm between the radiator and human body. 6. Antenna This modular has PCB pattern antenna. Any changes of antenna designs might require additional assessment. The Host antenna type shall be same type and antenna gain shall be less or equal to below information. Copyright. 2019. All Rights Reserved. 11/13 ATC5CPL004 User Manual 7. Label and compliance information The end user manual shall include all required regulatory information/warningas shown in this manual. If the FCC identification number is not visible when the module isinstalled inside another device, then the outside of the device into which the module isinstalled must also display a label referring to the enclosed module. This exterior label can use wording such as the following:
Contains FCC ID : YZP-ATC5CPL004 any similar wording that expresses the same meaning may be used. 8. Information on test modes and additional testing requirements This modular was tested in standalone configuration. Integration of this modular into ahost equipment would require additional testing. 9. Additional testing, Part 15 Subpart B disclaimer The grantee should include a statement that the modular transmitter is only FCC authorized for the specific rule parts (i.e., FCC transmitter rules) listed on the grant, and that the host product manufacturer is responsible for compliance to any other FCC rules that apply to the host not covered by the modular transmitter grant of certification. If the grantee markets their product as being Part 15 Subpart B compliant (when it also contains unintentional-radiator digital circuity), then the grantee shall provide a notice stating that the final host product still requires Part 15 Subpart B compliance testing with the modular transmitter installed. Copyright. 2019. All Rights Reserved. 12/13 ATC5CPL004 User Manual Module Integration Guide 10. ISED Statement This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canadas licence-exempt RSS(s). Operation is subject to the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes : (1) L'appareil ne doit pas produire de brouillage, et (2) L'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. Please notice that if the IC identification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following:
Contains IC : 7414C-ATC5CPL004 any similar wording that expresses the same meaning may be used. Ltiquette dhomologation dun module dInnovation, Sciences et Dveloppement conomique Canada devra tre pose sur le produit hte un endroit bien en vue, en tout temps. En labsence dtiquette, le produit hte doit porter une tiquette sur laquelle figure le numro dhomologation du module dInnovation, Sciences et Dveloppement conomique Canada, prcd du mot contient , ou dune formulation similaire allant dans le mme sens et qui va comme suit : Contient IC :7414C-ATC5CPL004 est le numro dhomologation du module This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 cm
(7.8 inches) between the antenna and your body. NOTE: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE USERS AUTHORITY TO OPERATE THE EQUIPMENT. Cet quipement est conforme aux limites d'exposition aux rayonnements IC dfinies pour un environnement non contrl. Cet quipement doit tre install et utilis avec une distance minimale de 20 cm (7,8 pouces) entre lantenne et votre corps. REMARQUE: LE FABRICANT NE PEUT TRE TENU RESPONSABLE DES INTERFRENCES RADIO OU TLVISES CAUSES PAR DES MODIFICATIONS NON AUTORISES DE CET APPAREIL. CES MODIFICATIONS PEUVENT ANNULER LAUTORITE DE LUTILISATEUR A FAIRE FONCTIONNER LAPPAREIL. Copyright. 2019. All Rights Reserved. 13/13