OPERATION DESCRIPTION Model: RBFA-C21SA FCC ID: YZP-RBFAC21SA Company LG INNOTEK CO.,LTD Signature Date Name Title 2014.10.06 J.S.SEO Engineer Product Information Description This product is applied to Class 2 Bluetooth Multimedia Module RBFA-C21SA which includes the CSR BC5-MM chipset and the integrated pattern antenna. Features
- Sensitivity : Typ. -88dBm
- Output Power : Typ. +2dBm Class 2
- Temperature Range : -40 ~ +85
- Supply Voltage : VDD 3.1V to 3.6V
- Interface : UART, USB
- Bluetooth Specification v3.0 with EDR Compliant Applications
- Automotive
- Bluetooth automotive wireless gateways Dimensions
* Power Supply Specification The power of DC3.1V ~ 3.6V is should be supplied to the Bluetooth module power(VDD). The module supplies the power to the each block depending on the function. Module input power in excess of the rated input power may cause damage to the internal components. And the influx of Surge and ESD also may lead to the damage of the modem in the vehicle. For the prevention of this, the module is necessary to design block the influx of Surge and ESD. Pin No. Signal Name Function
(Module case) MIN TYP MAX 11 VDD_3V3 In 3.1V 3.3V 3.6V
* RESET The RESETB pin is an active low reset and is internally filtered using the internal low frequency clock oscillator. A reset in performed between 1.5 and 4.0ms following RESETB being active. LGIT recommends that RESETB be applied for a period greater than 5ms between the falling and the rising threshold voltage. General Features 1) Bluetooth Module Features Bluetooth Power Class 2 Embedded Fully Bluetooth v2.0/v2.1/v3.0 + EDR System Compliant Embedded Bluetooth Profile Embedded AEC/NR Algorithm for Handsfree Full-speed Bluetooth Operation with Full Piconet Support Operation Voltage is 3.3V Single Power Rail Excellent Compatibility with Cellular Telephones Command and data Interface is UART and USB 16-bit Internal Stereo CODEC Support for 802.11 Co-existence RoHS Compliant 2) Functionality Key Features : 2.1+EDR Secure simple pairing Sniff subrating Encryption pause resume Packet boundary flags Encryption Extended inquiry response 3) Functionality Key Features : 2.0+EDR AFH, including classifier Faster connection: enhanced inquiry scan (immediate FHS response) LMP improvements Parameter ranges AFH as master and automatic channel classification Fast connect: interlaced inquiry and page scan plus RSSI during inquiry eSCO, eV3 + CRC, eV4, eV5 SCO handle Synchronization. 4) RBFA-C21SX Firmware Support Profile
-. A2DP1.2 with apt-X and AAC
-. AVRCP1.5(Controller) Block Diagram Packing Infomation Pad Type
-
Description Ground PIN Descriptions I/O No. Pin Name 1 2 3 4 GND I UART_RTS O UART_CTS UART_Rx I I Bidirectional CMOS output, tri-state, with weak internal pull-up CMOS input with weak internal pull-
down CMOS input with weak internal pull-
down 5 UART_Tx O Bidirectional CMOS output, tri-state, with weak internal pull-up 6 PCM_IN I CMOS input, with weak internal pull-
down 7 PCM_OUT O CMOS output, with weak internal pull-down 8 PCM_SYNC I/O Bidirectional with weak internal pull-
down 9 PCM_CLK I/O Bidirectional with weak internal pull-
down UART request to send active low UART clear to send active low UART data input UART data output
- Recommended external 4.7k Pull-up resistor. Synchronous data input
- The same pin as the I2S interface :
SD_IN Synchronous data output
- The same pin as the I2S interface :
SD_OUT Synchronous data Sync
- The same pin as the I2S interface : WS Synchronous data clock
- The same pin as the I2S interface : SCK Reset if low. Input debounced so must be low for >5ms to cause a reset Recommended external 4.7k Pull-up resistor & stability capacitor Positive supply for Module
- Supply voltage : Typical 3.3V. 10 RESET#
11 VDD_3V3 12 GND I I I CMOS input with weak internal pull-
up VDD
-
Ground 13 SPI_MISO O CMOS output, tristate, with weak internal pull-down 14 SPI_CSB I/O Input with weak internal pull-up 15 SPI_CLK I/O Input with weak internal pull-down 16 SPI_MOSI I CMOS input, with weak internal pull-
down SPI data output
- Used to program and configure (PS Keys), and debug the BC5-MM Chip select for SPI, active low
- Used to program and configure (PS Keys), and debug the BC5-MM SPI clock
- Used to program and configure (PS Keys), and debug the BC5-MM SPI data input
- Used to program and configure (PS Keys), and debug the BC5-MM 17 18 19 20 21 LED[1]
LED[0]
GND AGND O O I
-
-
-
-
-
LED LED Ground Analog Ground MIC_A_P I Analog Microphone input positive, left 22 MIC_A_N I Analog Microphone input negative, left
- Must be use external ESD protection No. Pin Name I/O Pad Type Description 23 24 25 26 27 28 29 30 31 32 33 34 35 36 Reserved AGND
-
SPK_B_N O Analog SPK_B_P O Analog SPK_A_N O Analog SPK_A_P O Analog GND GND AIO[0]
PIO[0]
PIO[1]
PIO[2]
PIO[3]
I I I/O I/O I/O I/O I/O USB_DN I/O 37 USB_DP I/O 38 39 40 41 42 43 44 45 46 47 48 GND PIO[10]
PIO[11]
PIO[9]
PIO[15]
PIO[12]
PIO[13]
GND GND GND GND I I/O I/O I/O I/O I/O I/O I I I I
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
Analog Ground Speaker output negative, right Speaker output positive, right Speaker output negative, left Speaker output positive, left Ground Ground TBD TBD TBD TBD TBD USB data minus USB data plus with selectable internal 1.5k Pull-up resistor Ground TBD TBD TBD TBD TBD TBD Ground Ground Ground Ground FCC Information This device complies with part 15 of the FCC Results. Operation is subject to the following two conditions :
(1) This device may not cause harmful interface, and
(2) This device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for CLASS B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try correct the interference by one or more of the following measures:
1.1. Reorient or relocate the receiving antenna. 1.2. Increase the separation between the equipment and receiver. 1.3. Connect the equipment into an outlet on a circuit different from that to which receiver is connected. 1.4. Consult the dealer or experienced radio/TV technician for help. WARNING Changes or modifications not expressly approved by the manufacturer could void the users authority to operate the equipment. Information for OEM Integrator This device is intended only for OEM integrators under the following conditions:
1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and 2) The transmitter module may not be co-located with any other transmitter or antenna. End product labelling The label for end product must include Contains FCC ID: YZP-RBFAC21SA. CAUTION : Exposure to Radio Frequency Radiation. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment must be installed and operated with minimum distance of 20cm between the radiator and your body. This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm may be maintained between the antenna and users.