2 2.9 Freezer Tag Graphic type ESL User manual Copyright. 2018. All Rights Reserved. 2. Updating new purchase image on Tag 2 To change purchase information on Tag, perform the following steps :
1. 2. Put remote controller near center of Tags display Press and hold Registration button on remote controller until Red LED off
(about 0.5 seconds) 3. When Tag is successfully received Registration data from remote controller, Tags display will be changed to Connected for a few minutes. That means Tag hides purchase image to read Tags IEEE MAC address through the Barcode scanner. 4. In NMS Client, download new purchase image to the Tag in registration status 5. When image downloading is finished successfully, Tags display will be changed to new purchase image Case1) If image downloading is failed, Tags display will be changed to Busy. After Alive Time, this Tag will be download new purchase image again Copyright. 2018. All Rights Reserved. 1. Overview 2 Remote control device provides customer with several functions as below Waking Tag up from sleep mode Updating new purchase image on Tag Deleting purchase image on Tag Returning a Tag to be factory settings Display Area Profile Hook Battery Cover A remote controller or a NFC Device contact point for communication. Button Function Two buttons provide customer with several functions as below
- Waking Tag up from sleep mode
- Updating new purchase image on Tag
- Changing purchase image on Tag Registration Keep Alive Next Image
< Button Function>
Copyright. 2018. All Rights Reserved. 3. Deleting purchase information on Tag 2 To release(delete) purchase information on Tag, perform the following steps :
1. 2. 3. Put remote controller near center of Tag display Press and hold Release button until red LED off (about 0.5 seconds) If Tag was received Reset command from remote controller, Tag will delete purchase information and Tags display will be changed to Ready 4. After step.3, Tag goes to deep sleep mode and doesnt communicate with gateway until receiving Keep Alive or Registration data from remote controller Copyright. 2018. All Rights Reserved. 4. Waking Tag up 2 Image 1 Image 2 To wake Tag up from sleep mode, perform the following steps :
1. 2. 3. Put remote controller near center of Tag display Press and hold Keep Alive button until Red LED off (about 0.5 seconds) Tag will wake up and goes to next step. Its depends on connection information with gateway case1) If this Tag wasnt connected with a gateway before sleep mode, go to 4-1 case2) If this Tag was connected with a gateway before sleep mode, go to 4-2 4-1. Searching gateway and goes to the next step. its depends on searching results case1) If Tag was successfully connected, Tags display will be changed to Ready case2) If Tag wasnt connected, Tags display(may be Ready) will be refreshed 4-2. Sending Keep Alive packet to gateway and Tag will go to sleep mode again case1) If Tag was received response from gateway, this Tag will go to sleep mode until the specified time in gateway. After sleep mode, this Tag will send Keep Alive Packet to gateway again. case2) If Tag wasnt received response from Gateway, this Tag will retry three times. After that, Tags display will be changed to Disconnected. Also this Tag will perform a whole channel scan every five minutes. Copyright. 2018. All Rights Reserved. 5. Returning a Tag to be factory settings 2 2016.10.20 14:34:59 353,003 To make a Tag to be factory reset status, perform the following steps :
1. 2. 3. Put remote controller near center of Tag display Press and hold Reset button until Red LED off (about 0.5 seconds) If Tag was received Reset command from remote controller, Tag goes back to factory settings and Tags display will be changed to Ready 4. After step.3, Tag goes to deep sleep mode and doesnt communicate with gateway until receiving Keep Alive or Registration data from remote controller case1) If Tag was received Keep Alive or Registration command from remote controller, this Tag will perform a whole channel scan. case2) If Tag was received Reset or Release command from remote controller, Tags display will be changed to Ready again Copyright. 2018. All Rights Reserved. 6. Tag status 2 Symbol Mode Image Deep Sleep Mode Connected with Gateway Disconnected with Gateway Battery discharge
(the battery needs to be replaced) Image download Failure(Busy) Copyright. 2018. All Rights Reserved. Regulation Information Trade name:
Manufacturer: LG Innotek Co., Ltd.
(Jangduk-dong) 26, Hanamsandan 5beon-ro, Gwangsan-gu, Gwangju, 62229, Korea Model name: REBL-MZ29E Operating frequency: 2405 MHz ~ 2480 MHz for Zigbee, 13.56 MHz for NFC (Receiving only) Maximum transmit power: 10 dBm for Zigbee Can be contacted via website: www.lginnotek.com FCC Compliance Statement (for products subject to Part 15) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation. Caution: Any changes or modifications to the equipment not expressly approved by the party responsible for compliance could void users authority to operate the equipment. This appliance and its antenna must not be co-located or operation in conjunction with any other antenna or transmitter. A minimum separation distance of 20 cm must be maintained between the antenna and the person for this appliance to satisfy the RF exposure requirement. CE RF Radiation Exposure Statement Caution: This equipment complies with European RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Caution Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to the instructions. EU Representative LG Innotek Co., Ltd. Am Limespark 2 (Innovapark) 65843 Sulzbach am Taunus, Germany
: ()
: ( )
: REBL-MZ29E
: () /
:
: R-C-LGW-REBL-MZ29E
- : IEEE 802.15.4 (Zigbee)
- : 2402 MHz ~ 2480 MHz (Zigbee), 13.56 MHz (NFC)
- : 16
- : 10 mW/MHz 20 SAR SAR
(B) ,
.