Inside your life !
PoE Wi-Fi Bridge Manual
(PoE: Power over Ethernet)
[Model Name : TWFB-R101D ]
2015. 03. 06
. 1. Appearance Description for PoE Wi-Fi Bridge 1. Front Panel
- The front panel has the 2-Button and status LEDs in the following figure. Buttons WPS Reset LEDs POWER WLAN DATA CAMERA Button Description WPS To connect WPS to AP(Access Point) Reset Reboot Reset to Factory Default LED Description Power Solid Yellow Green : Power on Off : Power is not supplied to the PoE Wi-Fi Bridge Solid Yellow Green : Wi-Fi Activity are in process Blinking Yellow Green : Wireless data is being sent or received. Blinking Red : The Wireless signal is weak signal WLAN Off : Wi-Fi access fail DATA Blinking Yellow Green : Ethernet link is detected Data Transmission on the port Off : No data transmission CAMERA Blinking Yellow Green : CAMERA link is detected Data Transmission on the port Off : No data transmission Fig 1. Front View Table 1. Front Description Copyright. 2015. All Rights Reserved. 1 / 12 2. Back/side Panel & Label Information
- The back/side panels have the wireless antenna, power plug and 2-Lan ports.
- The label on the bottom shows the MAC address, serial Number. Wireless Antenna AC 110V Power Label CAMERA (CAMERA LED) Fig 2. Back/side View DATA (DATA LED) Fig 3. Label information Copyright. 2015. All Rights Reserved. 2 / 12 2. Installation Guide 1. Log in connection Camera & Wi-Fi Bridge 1) Make sure that your camera is connected to the Wi-Fi Bridge CAMERA port with an Ethernet cable(wired) 2) Turn on the Wi-Fi Bridge and verify the following
- The power LED is On.
- The CAMERA LED is on for the LAN port that is connected to your Power device camera.
- The WLAN LED is blinking. 3) Launch internet browser and enter http://172.19.1.254 in the address field. You are prompted to login;
WLAN LAN Cable(CAMERA) CAMERA Fig 4. Login connection Copyright. 2015. All Rights Reserved. 3 / 12 2. Log in to the PoE 1) After entering http://172.19.1.254 , you can show Realtek WLAN AP webserver. Fig 5. Realtek WLAN webserver Copyright. 2015. All Rights Reserved. 4 / 12 3. Wireless Site Survey 1) Please click Wireless in the webserver. 2) Please click Site Survey in the webserver( , ), to fine AP list Click Click Fig 6. Wireless Site Survey Copyright. 2015. All Rights Reserved. 5 / 12 4. AP Connection 1) After Site Survey, you can show AP lists. 2) Please select wanted SSID(AP Name) and click Next Fig 7. SSID Selection Click Copyright. 2015. All Rights Reserved. 6 / 12 3) Please click Connect 4) After Connect click, You can show Please Wait message 5) It will be connected. Please click Reboot Later 6) Finally, Please close your web browser. Click Click Copyright. 2015. All Rights Reserved. 7 / 12 Fig 8. SSID Connection 3. Regulation Information INFORMATION TO THE USER This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/ TV technician for help. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation. Caution: Any changes or modifications to the equipment not expressly approved by the party responsible for compliance could void users authority to operate the equipment. This appliance and its antenna must not be co-located or operation in conjunction with any other antenna or transmitter. A minimum separation distance of 20 must be maintained between the antenna and the person for this appliance to satisfy the RF exposure requirements. Copyright. 2015. All Rights Reserved. 8 / 12 4. Regulation Information (French) Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes:
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. Cet quipement doit tre install et utilis avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps. Copyright. 2015. All Rights Reserved. 9 / 12 5. Appendix 1. WPS Function
- You can use WPS to connect AP without any password(WPA or WPA2). Push AP WPS button. Push PoE WPS Button(During 3 secs). When try to connect AP, WLAN LED is pulsing RED. After connect AP, WLAN LED is blinking Yellow Green. If you didnt push PoE WPS Button within 2min, It will be disconnected.
* Notice
- If you want to use WPS function, your AP must have WPS function. 2. Reset Function
- If you push RESET Button for 3secs, the PoE will restart. 3. Factory Default Setting WPS Reset
- Reset button can also be used to clear all data and restore the factory default settings. Fig 9. WPS / Reset Press the Reset button(during 10 secs). Release the Reset button. PoE will return to the factory configuration settings shown in the following table. Feature User name (case-sensitive) printed on product label Password (case-sensitive) printed on product label Static IP address Ethernet MAC address Subnet mask DHCP client Default settings admin xxxxx 172.19.1.254 See bottom label. 255.255.255.0 Disabled Table 2. PoE default configuration settings Copyright. 2015. All Rights Reserved. 10 / 12 4. PIN mode WPS Function of webserver Please click Wireless in the webserver. Please click WPS in the webserver. If you use PIN mode WPS, first input Self-PIN Number to AP. After that click Start PIN. Click ok. Click Click Click Click Copyright. 2015. All Rights Reserved. 11 / 12 5. PIN mode WPS Function of webserver Please click Wireless in the webserver. Please click WPS in the webserver. If you use PBC mode WPS in webserver, first push the WPS button of AP. After that click Start PBC. Click ok. Click Click Click Click Copyright. 2015. All Rights Reserved. 12 / 12