FCC ID: BEJLB885D 18.1-inch Color LCD Monitor

F-LAAT FRON cp ss5te Monitor Users Guide ete NCU TREY EE ees nee oe FCC Warning Class B Computing Device |

Information to the User This equipment has been tested and found to comply with the limits for a class B digital device pursuant to part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential tostal-

lation. This equipment generates, uses, and can radiate radio frequency energy and, if not instalicd and used in accordance with the instructions, may Cause harmful interference to radio communications. However, there is no guarantce that interference will not occur in a particular installation. If this equipment does cause interference to radio of television reception, which can be determined by tuming the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-Reorient or relocate the receiving anteona.

-Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-Consult the deaier or an experienced radio/TV technician for help and for additional suggestions. The user may find the following booklet prepared by the Federal Communica-

tions Commission helpful: How to Identify and Resolve Radio-TV intertercnce Problems." This booklet is available from the U.S. Government Printing Office, Washington, D.C. 20402, Stock No. 004-000-00345-4. FCC Warning The user 1s cautioned that changes or modifications not expressly approved by the manufacturer could void the user's authority to operate the equipment. NOTE: In order for an installation of this product to maintain compliance with the limits for a Class B device, shielded cables must be used. Introduction Installation Operation Technical Information Appendix Table of Contents introduction Important Precautions ENGLISH Connecting the Monitor Making use of USB (Universal Serial Bus) Feature Location and Function of Controls -

Control Panel Function _---__ On Screen Display (OSD) Control Adjustment _____-{)----

On Screen Display(OSD) Selection and Adjustment Q-

Energy Saving Design @

Low Radiation Compliance (MPR II), Self Diagnostics Messages and DDC (Display Data Channel) SS oo Video Memory Modes i ______ Troubleshooting _g___ Service @

Specifications qD-

Communications Regulation Information. -________-see back of manual Environmental Labelling of Personal Computers. _se hack of manual-~--__--

Introduction Features Monitor Registration The model and serial numbers are found on the rear of this unit. These numbers are unique to this unit and not available to others. You should record requested information here and retain this guide as a permanent record of your purchase. Staple your receipt here. Date of Purchase Dealer Purchased From:

Dealer Address Dealer Phone No. Model No. Serial No. Introduction The FLATRON LCD 885LE Flat Panel Monitor has an active matrix TFT (Thin-Film Transistor) LCD (Liquid Crystal Display). This monitor is designed for use in small working areas or for those who need more working space on the desk. The FLATRON Lo asst is a 18.1-inch (18.1 inches viewable) intelligent microprocessor based monitor. Two signal ports (Dsub port and DVI-D port} on the rear panel allow 2 connections to 2 computers at a time. The DVI - D (Digital Visual Interface - integrated) port supports analog and digital signal inputs and also improves quality of the displayed image by eliminating poor video at the monitor source. We accomplished to adapt the advanced design and technology to the monitor. Soft touch buttons on the front panel are simple and allow you to conveniently adjust a variety of image controls. The absolute flat screen and screen surface treatment eliminate distracting glares. USB (Universal Serial Bus) ports at the back of the monitor are prepared for the USB cable and hub. You can easily and flexibly connect USB-

designed devices-such as a mouse, keyboard or printer- to the monitor for true Plug and Play function. Digitally controlled auto-scanning is done with the micro-processor for horizontal scan frequencies between 31 and 81kHz, and vertical scan frequencies between 56 - 85Hz. The microprocessor-based intelligence allows the monitor to operate in each frequency mode with the precision of a fixed frequency monitor. ft supports resolutions up to 1280x1024, and has a wide viewing angle of +80 degrees horizontal and +80 degrees vertical. For greater user health and safety, this monitor complies with the stringent Swedish TCO99 requirements for low radiation emissions. For low cost of monitor operation, this monitor is certified as meeting the EPA Energy Star requirements, and utilizes the VESA Display Power Management Signalling (DPMS) protocol for power saving during non-

use periods. i t

Introduction On Safety Important Precautions This unit has been engineered and manufactured to assure your personal safety, but improper use can result in potential electrical shock or fire hazard. In order not to defeat the safeguards incorporated in this monitor, observe the following basic rules for its installation, use, and servicing. Also follow all warnings and instructions marked directly on your monitor. Use only the power cord supplied with the unit. In case you use another power cord, make sure that it is certified by the applicable national standards if not being provided by the supplier. if the power cable is faulty in any way, please contact the manufacturer or the nearest authorized repair service provider for a replacement. Operate the monitor only frorn a power source indicated in the specifications of this manual or listed on the rnonitor. If you are not sure what type of power supply you have in your home, consult with your dealer. Overloaded AC outlets and extension cords are dangerous. So are frayed power cords and broken plugs. They may result in a shock or fire hazard. Call your service technician for replacement. Do.not Open the Monitor. There are no user serviceable components inside. There are Dangerous High Voltages inside, even when the power is OFF. Contact your deaier if the monitor is not operating properly. To Avoid Personal Injury :

Do not place the monitor on a sloping shelf unless property secured. a Use only a stand recommended by the manufacturer. Donot try to roll a stand with smail casters across thresholds or deep pile carpets. To Prevent Fire or Hazards:

Always turn the monitor OFF if you leave the room for more than a short period of time. Never leave the monitor ON when leaving the house. Keep children from dropping or pushing objects into the monitor's cabinet openings. Some intemal parts carry hazardous voltages. Do not add accessories that have not been designed for this monitor. During a lightning storrn or when the monitor is to be left unattended for an extended penod of time, unplug it from the wail outlet. Do not bring magnetic devices such as magnets or motors near the picture tube. LEP ADR Mh deg See agar Introduction On Installation On Cleaning On Repacking Important Precautions Do nat allow anything to rest upon or roll over the power cord, and do not place the monitor where the power cord is subject to damage. Do not use this monitor near water such as near a bathtub, washbow|, kitchen sink, laundry tub, in a wet basement, or near a swimming pool. Monitors are provided with ventilation openings in the cabinet to allow the release of heat generated during operation. If these openings are blocked, built-up heat can cause failures which may result in a fire hazard. Therefore, NEVER:

Block the bottom ventilation slots by placing the monitor on a bed, sofa, rug, etc. Place the monitor in a built-in enclosure unless proper ventilation is provided. Cover the openings with cloth or other material. Place the monitor near or over a radiator or heat source. Do not rub or strike the Active Matrix LCD with anything hard as this may scratch, mar, or damage the Active Matrix LCD permanently. Do not press the LCD screen with your finger for a long time as this may incur some afterimages. Some dot defects may appear on the screen, like Red, Green or Blue spots on the screen. However, this will have no impact or effect on the monitor performance. if possible, use the VESA 1280x1024 @60Hz video mode to obtain the best image quality for your LCD monitor. If used under any modes except the VESA 1280x1024 @60Hz video mode, some scaled or processed images may appear on the screen. However, this is the characteristics of the LCD panel which has a fixed resolution of 1280x1024 at 60Hz. Unplug the monitor before cleaning the face of the LCD screen. Dust the monitor by wiping the screen and the cabinet with a soft, clean cloth. If the screen requires additional cleaning, use a clean, damp cloth. Donot use liquid cleaners or aerosol cleaners. Do not throw away the carton and packing materials. They make an ideal container in which to transport the unit. When shipping the unit to another location, repack it in Its original material. Installation Connecting the Monitor To set up the monitor, ensure that the power is turned off to the monitor, computer system, and other attached devices, then follow these steps:

1. Place the monitor in a convenient, well-ventilated location near your computer. 2. Remove the stand cover of the monitor to connect the cables. 3. Connect the signal cable. When connecting the DVI-D signal cable ..... Figure 1 Conneci ihe end of monitor signal cable to the port on the rear panel of the monitor through the slot and cable holder on Stand, Connect the other end to the DVI port on the rear panel of the computer and tighten the screws. @

= When connecting the Dsub signal cable PC le. Figure 2 Connect one end of the monitor signal cable to either of the connectors @ on the rear panel of the monitor. Connect the other end to the Dsub port on the rear panel of ihe computer and tighten the screws. @

MAC... Figure 3 Connect one end of the monitor signal cable to either of the connectors @ on the rear panel of the monitor. Connect the other end of the monitor signal cable to the rear panel of Macintosh computer through a Macintosh adapter and then tighten screws. @

4. Connect the plug from the AC adapter into the back of the monitor. 8 Figure 1 There should be a DVI port on the Stand Cover Power Cord AC adapter Signal Cable Installation Connecting the Monitor Figure 2 Fu Stand Cover of Dsub Power C -_ ower Cor AC adapter Signal Cable Figure 3 Saeco 9 ely purchased adapter. For

: i th 8 ti ee

( Oe Stand Cover Re Power Cord een =

AC adapter Signal Cable 5, Connect one end of the AC power cord to the AC adapter @ and the other end to a properly grounded AC outlet that is easily accessible and close to the monitor. 6. After connecting cables, put stand cover correctly into the holes unders stand. If securely connected, you can hear click sound from the latch. 7. Power ON the PC, then the monitor. 8. If you see the NO SIGNAL message, check the signal cable and connectors. 9, After using the system, power OFF the monitor, then the PC. Note: If you see the INPUT SIGNAL OUT OF RANGE message, check to make sure your systern is set to one of the factory preset modes (see page A15), or is set to a resolution and refresh rate within the specification limits of this monitor. a Installation USB connection Making use of USB (Universal Serial Bus) Feature USB (Universal Serial Bus) is an innovation in connecting your different desktop peripherals conveniently to your computer. By using the USB, you will be able to connect your mouse, keyboard, printer, and other peripherals to your monitor instead of having to connect them to your computer. This will give you greater flexibility in setting up your system. USB allows you to connect chain up to 120 devices on a single USB port, and you can hot plug (attach them while the computer is running) or unplug them while maintaining Plug and Play auto detection and configuration. This monitor has an integrated self-powered USB hub, allowing up to 4 other USB devices to be attached it. L. Connect the upstream port of the monitor to the downstream port of the USB compliant PC or another hub using the USB cable (Computer must have a USB port). 2. Connect the USB compliant peripherals to the downstream parts of the monitor.

- eg ae G 4 ee USB downstream Ports oo connect the cables from USB o o compliant peripherals-such as 0? keyboard, mouse, printer, scanner, etc To USB downstream port of the USB compliant PC or another hub cable USB Upstream connector

[2] T=D | == [|e 4 USB Downstream connector Installation USB specifications Making use of USB (Universal Serial Bus) Feature 4 Example of connection scanner NOTE 7

- To activate the USB hub functic

-. compliant PC(OS) or another hu

=. When connecting the USB cable, check that the shap. cable side matches the _s When the monitor i i Evenif the monitor is i a powe avingm

"function when they are connected the USB

.; .downstream) of the monitor. SE LS Ua NL a a aN I I Te epg RTT USB standard Rev. 1.1 complied setftpowered hub Downstream power supply 500mA for each (MAX) Communication speed . 12 Mbps (full), 1.5 Mbps (low) USB port me i 1 Upstream port 4 Downstream ports Pee ee

@)ey-1e- lire) Location and Function of Controls Front View Power Button OSD Power Indicator Button <

AV/< Bb Buttons Rear View USB downstream ports USB upstream port Dsub Signal port DVI-D port (Digital) DC Power port Cable Holder O-C-O Used to hold the cables in place Stand Cover Operation Front Pane! Controls

<Shortcut Keys>

+ Brightness and Contrast can be adjusted directly without entering the On Screen Display (OSD) system. Touch the <7 buttons to adjust the settings and then the OSD button to save all changes. The Brightness and Contrast functions are also available in the On Screen Display (OSD) menu.

<Auto Button>

+ This function is suitable for analog signal input only. This button is for the automatic adjustment of the screen position, clock and phase. Note: Some signal from some graphics boards may not function properly. If the results are unsatisfactory, adjust your monitor's Position, Clock and Phase manually. oO Control Panel Function Use this button to enter or exit the on screen display.

! . screen display. a/< & Buttons Use these buttons to choose of adjust items in the on Power Button Use this button to turn the monitor on or off. Auto Button SOURCE/SET Button e Use this button to make Dsub or DVI connector active. This feature is used when two computers are connected to the monitor. The default setting ts Dsub.

* Use this button to enter a selection in the on screen display. Power Indicator The power indicator light is shown in the power button. This indicator lights

| up green when the monitor operates normally. If the monitor is in DPM

| (Energy Saving) mode (stand-by/

suspend/power off), this indicator

+ color changes to amber. i

Operation On Screen Display (OSD) Control Adjustment Making adjustments to the image size, position and operating parameters of the monitor are quick and easy with the On Screen Display Control system. A quick example is given below to familiarize you with the use of the controls. Following section is an outline of the available adjustments and selections you can make using the OSD. adjustment,"

RBI ore Nae tle ached Pee eee oa we oe ead BoP die bs To make adjustments in the On Screen Display, follow these steps:

A osp@) < [> ,j SOURCE/SET Touch the OSD Button, then the main menu of the OSD appears. To acces a control, use the 4 or V Buttons. When the icon you want becomes highlighted, touch the SOURCE/SET Button. Use the AV/<] > Buttons to adjust the item to the desired level. Accept the changes by touching the SOURCE/SET Button. 1 Q 8 4 S Exit the OSD by touching the OSD Button. O)e-Tees A ospO -+ 4 > [By sourceser V Na osp ) < 3 sourceser < 7 p NOTE. a Whena digital signal is set as an. input, only the BRIGHTNESS, CONTRAST and SETUP properties... can be adjusted. You do not need to. adjust the other properties. On Screen Display(OSD) Selection and Adjustment You were introduced to the procedure of selection and adjusting an item using the OSD system. Listed below are the icons, icon names, and icon descriptions of the items that are shown on the Menu. eR RAG res pee Cay a BRIGHTNESS / CONTRAST OD Oo Brightness Used to adjust the brightness of the screen. Contrast Adjust the display to the contrast desired. Jo0 PRESET 900K PRESET RED GREEN BLUE 9300K/6500K To appear the displays color temperature.

* 9300K:Slightly bluish white.

* 6500K:Slightly reddish white. To set your own color levels. POSITION a 61 aoe eae ct Bx Vertical Position To move image up and down. Horizontal Position To move picture image left and right. oso @ Eksounceser af >

Vv Gute diem Operation On Screen Display(OSD) Selection and Adjustment

, (en Ses [ prayer ints CLOCK To minimize any vertical bars or stripes visible on the screen background. The horizontal screen size will also change. PHASE To adjust the focus of the display. This item allows you to remove any horizontal noise and clear or sharpen the image of characters. Phase adjustment should be done after adjusting the Clock. LANGUAGE To choose the language in which SETUP LANGUAGE F ENGUSH the control names are displayed. IMAGE SIZE > FULL OSD POSITION > De} . :

MODE INFO TON IMAGE SIZE This function displays the image in

- ELAPSEDTIME . 0000SH. its original size or enlarged size so

"+ 91280x1024H2@60H2 *. eg BRESET MODE as to fit in the full screen of the

.DSUB ANALOG LCD panel. OSD POSITION To adjust position of the OSD window on the screen. MODE INFO This function displays the current mode information on the screen when power on the monitor. BEEP To select beep ON or OFF. ELAPSED To display the use time of TIME monitor. sent Technical Information Power Consumption Energy Saving Design This monitor complies with the EPA's Energy Star program, which is a program designed to have manufacturers of computer equipment build circuitry into their products to reduce power consumption during time of nor-use. This monitor also goes into its energy saving mode if you exceed the monitor's operating limits, such as the maximum resolution of 1280x1024 or the frequency refresh rates of 31-81kHz horizontal or 56-85Hz vertical. When this monitor is used with a Green or EPA Energy Star PC, or a PC with a screen bianking software following the VESA Display Power Management Signalling (DPMS) protocol, this monitor can conserve significant energy by reducing power consumption during periods of non-

use. When the PC goes into the energy saving mode, the monitor will go into a suspended operation state, indicated by the Power LED light changing from a green color to an amber color. After an extended period in the suspended mode, the monitor will then enter a semHOFF mode to conserve more energy. In the sem+OFF mode or DPMS OFF mode as we call it in our specifications, the Power LED will still show an amber color. When you awaken your PC by hitting a key or moving the mouse, the monitor will also awaken to its normal operating mode, indicated by the green Power LED light. By following these conventions, the power consumption can be reduced to the following levels:

Hori. Verti. Power As is Sync AYiTe ete) Consumption Raa T eg Normal(Max.) On On Normal < 60W Green Stand-by Off On Off < 5W Amber Suspend On Off Off < ow Amber Power Off Off Off Off < 5w Amber te (va ps Technical Information Low Radiation Compliance (MPR II), Self Diagnostics Messages and DDC (Display Data Channel) Low Radiation Compliance This monitor meets one of the strictest guidelines available today for low

(MPR Il) radiation emissions, offering the user extra shielding and an antistatic screen coating. These guidelines, set forth by a government agency in Sweden, limit the amount of emission allowed in the Extremely Low Frequency (ELF) and Very Low Frequency (VLF) electromagnetic range. Self Diagnostics Messages Special Seif Diagnostics messages will appear on the screen when identifying the following monitor conditions:

= NO SIGNAL This OSD may pop up when it is ON but no m signal is detected. in this case the message 4 NO SIGNAL will be highlighted, alerting you to check the signal cable connections. CHECK SIGNAL CABLE ws INPUT SIGNAL OUT OF RANGE we 1s OSD may appear to inform you that the M INPUTSIGNAL # Signal being sent to the monitor is not within

: * its frequency range. In this case, you would need to check the resolution and refresh rate you have your video card set to, and adjust to be within the range of the monitor. a OUT OF RANGE POWER MANAGEMENT 20SEC DDC (Display Data Channel) DDC is a communication channel over which the monitor automatically informs the host system (PC) about its capabilities. This monitor has two DDC function; DDC1 and DDC2B. DDC? and DDC2B carry out uni-

directional communication between the PC and the monitor. Under these Situations, the PC sends display data to the monitor but not commands to control the monitor settings. NOTE Bes

= PC must support DDC functions to do this. a Technical Near Video Memory Modes The monitor has 26 memory locations for display modes, 16 of which are factory preset to popular video modes. Display Modes iene nace ps j P solution} Display Modes (Resolution) rate | ears 1 VGA 640x350 31.469 70 D-Sub/DVi 2 VGA 720x400 31.468 70 D-Sub/DVI 3 VGA 640x480 31.469 60 D-Sub/DVI 4 VESA 640 x 480 37.500 75 D-Sub/DVI 5 VESA 640 x 480 43.269 85 D-Sub/DVI 6 VESA 800x600 37.879 60 D-Sub/DVI 7 VESA_ 800 x 600 46.875 75 D-Sub/DV!

8 VESA_ 800 x 600 53.674 85 D-Sub/DV 9 MAC 832x624 49.725 75 D-Sub/DVI 10 VESA 1024 x 768 48.363 60 D-Sub/DVI 11. VESA 1024 x 768 60.123 75 D-Sub/DVI 12 VESA 1024 x 768 68.677 85 D-Sub/DVI 13. MAC 1152 x 870 68.681 75 D-Sub/DVI 14. VESA 1152 x 900 61.805 65 D-Sub/DV1 15 VESA 1280 x 1024 63.981 60 D-Sub/DVI 16 VESA 1280x1024 79.976 75 D-Sub A User Modes s Modes 17-26 are empty and can accept new video data. If the rnonitor detects a new video mode that has not been present before or is not one of the preset modes, it stores the new mode automatically in one of the empty modes starting with mode 17. If you use up the 10 blank modes and still have more new video modes, the monitor replaces the information in the user modes starting with mode 17. Recalling Display Modes When your monitor detects a mode it has seen before, it autornatically recalls the image settings you may have made the last timie you used that mede. You may, however, manually force a recall of each of the 16 preset modes by pressing the Recall button. All preset modes are automaticaily recalled as the monitor senses the incoming signal. The ability to recall the preset modes is dependent on the signal coming from your PCs video card or system. If this signal does not match any of the factory modes, the monitor automatically sets itself to display the image.

(NOTE a Ifthe power dicatoxLED) ight iS. uf blinking amber, F may: result in :

--abriomal condition, of the monitor. Then press a power ON/OFF:

button on-the front panel control and cali your service technician for:

more information. :

Technical Information Troubleshooting Check the following before calling for service. Display Position is incorrect. a Select AUTO from the OSD menu, and press/> to activate the function. Ifthe results are unsatisfactory, adjust the image position using the H position and V position icon in the on screen display. On the screen background, vertical bars or stripes are visible. Select AUTO from the OSD menu, and press/> to activate the function. Ifthe results are unsatisfactory, decrease the vertical bars or stripes using the CLOCK icon in the on screen display. Any horizontal noise appearing in any image or characters are not clearly portraid. Select AUTO from the OSD menu, and press/> to activate the function.

|f the results are unsatisfactory, decrease the horizontal bars using the PHASE icon in the on screen display. NO SIGNAL message. The signal cable is not connected, or is loose. Check and secure the connection. INPUT SIGNAL OUT OF RANGE message appears. Picture is blank. The frequency of the signal from the video card is outside the operating range of the monitor.

*Horizontal Frequency: 31kHz-81kHz

*Vertical Frequency: 56Hz-85Hz Use ihe graphics board's utility software to change the frequency setting (Refer to the manual for graphics board). You can change the setup to the supported resolution using the Safe Mode

(Press the F8 key during booting the system). The power LED is illuminated amber. The monitor is in its display power management mode. There is no active signal coming from the PC. The signal cable is not fastened securely. Check the computer power and graphics adapter configuration. The monitor doesn't enter the power saving off mode (Amber). Computer video signal is not VESA DPMS standard. Either the PC or the video controller card is not using the VESA DPMS power management function. Technical Information Service Unplug the monitor from the wall outlet and refer servicing to qualified service personnel when :

The power cord or plug is damaged or frayed. Liquid has been spilled into the monitor. The monitor has been exposed to rain or water. The monitor does not operate normally following the operating instructions. Adjust only these contrals that are covered in the operating instructions. An improper adjustment of other controls may result in damage and often requires extensive work by a qualified technician to restore the monitor to normal operation. The monitor has been dropped or the cabinet has been damaged. The monitor exhibits a distinct change in performance. Snapping or popping from the monitor is continuous or frequent while the monitor is operating. It is normal for some monitors to make occasional sounds when being turned on or off, or when changing video modes. Do not attempt to service the monitor yourself, as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel. Signal Connector Pin Assignment RCE Hae AC-DC Adapter Technical Information Specifications

" a VGA Connector Signal(D-Sub) alae EEE Red Video 2 Green Video om Salona 3 Blue Video 1 Ground 4 Ground 12 SDA 5 Ground 13 H. Syne. 6 Red Ground 14 V. Sync. 7 Green Ground 15 SCL 8 Blue Ground NOTE No. 5 Pin have to ground on the PC side. a DVI-I Connector (Digital/Analog) 1 T.M. 0. S. Data2- Hot Plug Detect 2 T.M.O.S. Data2+ 7 T.M.D.S. Datad-

3 T.M. D.S. Data2/4 Shield 18 T.M. DO. S. DataO+

4 TM. D.S. Datad- 19 T.M. D.S. Data0/5 Shield 5 T.M.D.S. Datad+ 20 T.M. D.S. Datad-

6 DDC Clock 21 T.M. D.S. Datab+

7 DDC Data 22 T.M. D. S. Clock Shield 8 alog Vertical Sync. 23 T.M.D.S. Clock+

9 T.M. D.S. Datal- 24 T: M.D. S. Clock-

10 T.M.D.S. Datal+

11 T.M.D.S. Datal/3 Shield 12 T.M. D.S. Data3-

13 T.M.D.S. Data3+

14 +5V Power 15 Ground (return for +5V, H. Syne. and V. Syne}

T.M. D. S. (Transition Minimized Differential Signaling) weet Input Output See eee aaeae er I OI INES OARS SEC FI Tee eT AC 100-240V_ ~1.5-1.0A 50/60Hz DCI2V 5.0A Oc-@

NERS SR Se RPO PRIOR OT NT ZL TPO RN TTR DR OE A SE Se ON rN ERR Use only the AC-DC adapter supplied with the monitor. Technical Information Display Sync Input Video Input Power Input Dimensions Weight Til/Swivel Range Environment Conditions Specifications Type 18. linch (45.97cm} Flat Panel Active matrx-TFT LCD Ant+Glare coating Viewable Size 18.1inch (45.97cm) Viewing Angle (max.) 80 (Left / Right / Up / Down) Pixel pitch 0.28 x 0.28mm True color 16.7 million color Horizontal Freq. SIKHz - 81kHz (Automatic) Vertical Freq. 56Hz - 85Hz (Automatic) Input form Separate, TTL, Positive/Negative Composite, TTL, Positive/Negative SOG (Sync On Green}

Digital Signal input 15 pin D-Sub connector / DVI - D connector (AnalogDigital) input Form Separate, RGB Analog, 0.7Vp-p/750hm, Positive, Digital Resolution Max VESA 1280 x 1024 @75Hz Recommend VESA 1280x 1024 @60Hz DC 12V 5.04 Width 43.6cm / 17.2inches Height 45.7cm / 18.0inches Depth 20.5cm /8.07inches Net 8.9kg/ 19.62lbs Tilt 5 (Down) / 30 (Up) Swivel 30 (Left) / 30 (Right) Operating condition Temperature 10C to 35C Humidity 10% to 80% non-condensing Storage condition Temperature -20C to 60C Humidity 5% to 95% non-condensing NOTE Information in this dcument is subject to change with! Lo FCC Compliance Statement Canadian DOC Notice CE Conformity Notice C Communications Regulation Information This equipment has been tested and found to comply within the limits of a Class B digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception (which can be determined by turning the equipment on and off, the user is encouraged to try to correct the interference by using one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and the recever. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Caution: Changes or modifications not expressly approved by the party responsible for compliance could void the user's {or your) authority to operate the equipment. Only peripherals (digital input/output devices, terminals, printers, etc.) certified to comply with the Class B limits may be attached to this monitor. Operation with non-certified peripherals is likely to result in interference to radio and TV reception. Only shielded signal cables may be used with this System. NOTICE The regulations are applied only to the products with the ID LABEL indicating specific requirements. This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. Cet appareil numrique de la classe B respecte toutes les exigences du Rglement sur le matriel brouilleur du Canada. NOTICE The regulations are applied only to the products with the ID LABEL indicating specific requirements. Products with the "CE" Marking comply with the EMC Directive(89/336/EEC) and LOW VOLTAGE Directive (73/23/EEC) issued by the Commission of the European Community. Compiance with these directives implies conformity to the following European Norms :

* EN 55022 ; Radio Frequency Interference

* EN 50082-1:1992 ; Electromagnetic Immunity

* EN 60555-2 ; Power Line Harmonics

* EN 605553 ; Voltage Fluctuations

* EN 60950 ; Product Safety NOTICE The regulations are applied only to the products with the IO LABEL indicating specific requirements. Appendix APPENDIX Appendix Congratulations!

Why do we have environmentally labelled computers?

Environmental Labelling of Personal Computers You have just purchased a TCO99 approved and labelled product! Your choice has provided you with a product developed for professional use. Your purchase has also contributed to reducing the burden on the environment and also to the further development of environmentally adapted electronics products. This product meets the requirements for the TCO'99 scheme which provides for an international environmental and quality labelling of personal computers. The labelling scheme was developed as a joint effort by the TCO (The Swedish Confederation of Professional Employees}, Svenska Naturskyddsforeningen (The Swedish Society for Nature Conservation), Statens Energimyndighet (The Swedish National Energy Administration) and SEMKO AB. The requirements cover a wide range of issues: environment, ergonomics, usability, reduction of electric and magnetic fields, energy consumption and electrical safety. In many countries, environmental labelling has become an established method for encouraging the adaptation of goods and services to the environment. The main problem, as far as computers and other electronics equipment are concerned, is that environmentally harmful substances are used both in the products and during their manufacture. Since it is not so far possible to satisfactorily recycle the majority of electronics equipment, most of these potentially damaging substances sooner or later enter nature. There are also other characteristics of a computer, such as energy consumption levels, that are important from the viewpoints of both the work (internal) and natural (external) environments. Since all methods of electricity generation have a negative effect on the environment (e.g. acidic and climate-influencing emissions, radioactive waste}, it is vital to save energy. Electronics equipment in offices is often left running continuously and thereby consumes a lot of energy. What does labelling involve?

Environmental requirements Appendix Environmental Labelling of Personal Computers The environmental demands impose restrictions on the presence and use of heavy metals, brominated and chlorinated flame retardants, CFCs

(freons) and chlorinated solvents, among other things. The product must be prepared for recycling and the manufacturer is obliged to have an environmental policy which must be adhered to in each country where the company implements its operational policy. The energy requirements include a demand that the computer and/or display, after a certain period of inactivity, shall reduce its power consumption to 4 lower level in one or more stages. The length of time to reactivate the computer shall be reasonable for the user. Labelled products must meet strict environmental demands, for example, in respect of the reduction of electric and magnetic fields, physical and visual ergonomics and good usability. Below you will find a brief summary of the environmental requirements met by this product. The complete environmental criteria document may be ordered from:

TCO Development SE-114 94 Stockholm, Sweden Fax: +46 8 782 92 07 Email (Internet): develooment@tco.se Current information regarding TCO99 approved and labelled products may also be obtained via the Internet, using the address: http://www.tco-info.com/

Flame retardants Flame retardants are present in printed circuit boards, cables, wires, casings and housings. Their purpose is to prevent, or at least to delay the spread of fire. Up to 30% of the plastic in a computer casing can consist of flame retardant substances. Most flame retardants contain bromine or chloride, and those flame retardants are chemically related to another group of environmental toxins, PCBs. Both the flame retardants containing bromine or chloride and the PCBs are suspected of giving rise to severe heaith effects, including reproductive damage in fish-eating birds and mammals, due to the bio-accumulative* processes. Flame retardants have been found in human blood and researchers fear that disturbances in foetus development may occur. Appendix Environmental Labelling of Personal Computers The relevant TCO99 demand requires that plastic components weighing more than 25 grams must not contain flame retardants with organically bound bromine or chlorine. Fiame retardants are allowed in the printed circuit boards since no substitutes are available. Cadmium**

Cadmium is present in rechargeable batteries and in the colour-generating layers of certain computer displays. Cadmiurn damages the nervous system and is toxic in high doses. The relevant TCO99 requirement states that batteries, the colour-generating layers of display screens and the electrical or electronics cornponents must not contain any cadmium. Mercury**

Mercury is Sometimes found in batteries, relays and switches. It damages the nervous system and is toxic in high doses. The relevant TCO99 requirement states that batteries may not contain any mercury. tt also demands that mercury is not present in any of the electrical or electronics components associated with the labelled unit. There is however one exception. Mercury is, for the time being, permitted in the back light system of flat panel monitors as there today is no commercially available alternative. TCO aims on removing this exception when a mercury free alternative is available. CFCs (freons) The relevant TCO99 requirement states that neither CFCs nor HCFCs may be used during the manufacture and assembly of the product. CFCs

(freons) are sometimes used for washing printed circuit boards. CFCs break down ozone and thereby damage the ozone layer in the Stratosphere, causing increased reception on earth of ultraviolet light with e.g. increased risks of skin cancer (malignant melanoma) as a consequence. Lead**

Lead can be found in picture tubes, display screens, solders and capacitors. Lead damages the nervous system and in higher doses, causes lead poisoning. The relevant TCO99 requirement permits the inclusion of lead since no replacement has yet been developed.

* Bio-accumulative is defined as substances which accumulate within living organisms

** Lead, Cadmium and Mercury are heavy metals which are Bio-accumuiative.