FCC ID: BEJIGCJ1PMN Car AVN

1. P/G-IVI Introduction, Specification P/G-IVI (Plugin In-Vehicle Infotainment) IVI device equipped in the JLR(Jaguar Land Rover) vehicles. In charge of wireless communications in WLAN, BT Multi functional AVN such as Broadcast, Media, Phone and so on P/G-IVI Specification 1. Model Name : IGCJ1PMN 2. Supported band : 2.4/ 5GHz WLAN (UNII 1, 3), BT v4.2 (BDR/EDR) 3. Supply Voltage : 6.5~16V 4. DC Current : ~ 7A 5. Temperature Range : (-)40 ~ 75C Item Middle Line NA/Row Modem Technology RF variants(Market variants) Navigation Modem / AP Broadcast Ethernet(BCBR) WiFi Client CAN BUB

<Major Functions>

X X O O O O O X HSCAN LGE Confidential 2. P-IVI Specification P-IVI Specification

- RF Band Information Function Frequency (MHz) Wi-Fi 2.4GHz Wi-Fi 5GHz Bluetooth 2412-2462 5745-5825 5755-5795 5180-5240 5190-5230 5210 2402-2480 SISO MIMO SISO

* WLAN operation in 5150-5350MHz is restricted to Indoor operation. LGE Confidential 3. Appendix equipment. FCC Part 15.21 statement Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this FCC Part 15.19 statement This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. RF Exposure (MPE) This equipment complies with FCC and IC RF Radiation exposure limits set forth for an uncontrolled environment. This device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and your body. Cet quipement est conforme l'exposition de FCC et IC rayonnements RF limites -tablies pour un environnement non contrl. Lantenne pour ce transmetteur ne doit pas tre mme endroit avec dautres metteur sauf conformment FCC et IC procdures de produits Multi-metteur. Cet quipement doit tre install et utilis avec une distance minimale de 20 cm entre le radiateur et votre corps. ISED Statement This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canadas licence-exempt RSS(s). Operation is subject to the following two conditions:

(1) This device may not cause interference.

(2) This device must accept any interference, including interference that may cause undesired operation of the device. Lmetteur/rcepteur exempt de licence contenu dans le prsent appareil est conforme aux CNR dInnovation, Sciences et Dveloppement conomique Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes :

(1) Lappareil ne doit pas produire de brouillage;

(2) Lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. LGE Confidential

IGCJ1PMN - Main Label Regulation / P-IVI GSDB Code : GJNZB DUNS Code : 555343750

/ DC 3.9 V 5 A LG Electronics MADE IN VIETNAM FCC ID : BEJIGCJ1PMN IC: 2703H-IGCJ1PMN LG Electronics European Shared Service Center B.V. Krijgsman 1, 1186 DM Amstelveen, The Netherlands Este equipamento opera em carter secundrio, isto , no tem direito a proteo contra interferncia prejudicial, mesmo de estaes do mesmo tipo, e no pode causar interferncia a sistemas operando em carter primrio. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.

<Top view of EUT>

LGE Confidential

LG Electronics USA 1000 Sylvan Avenue Englewood Cliffs, New Jersey, United States Date: May 10th, 2019-05-10 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road, Columbia, MD21046 Attn: Office of Engineering and Technology Subject: Attestation letter regarding UNII client device without radar detection capability FCC ID: BEJIGCJ1PMN To whom it may concern, We, LG Electronics USA, declares that the device does not support channel 12~13 in 2.4GHz band any non-US, Canada channels in all the operational mode(s) for FCC ID: BEJIGCJ1PMN. With reference to KDB 905462 D032, we, LG Electronics Inc., hereby declare the following for FCC ID: BEJIGCJ1PMN. The device client software and associated drivers will not initiate any transmission on DFS frequencies without initiation by a master. This includes restriction on transmissions for beacons and support for ad-hoc peer-to-peer modes.

[Wi-Fi Direct is NOT supported]

Channel/Frequency Plan:

1) 2.4GHz Frequency(MHz) Channel Scanning(active/passive) ad-hoc mode(y/n) 2412 2417 2422 2427 2432 2437 2442 2447 2452 2457 2462 1 2 3 4 5 6 7 8 9 10 11 A A A A A A A A A A A N N N N N N N N N N N 2) 5GHz Frequency(MHz) Channel Scanning(active/passive) ad-hoc mode(y/n) 5180 5190 5200 5210 5220 5230 5240 5260 5280 5290 5300 5320 5500 5520 5530 5540 5560 5580 5600 5620 5640 5660 5680 5700 5745 5765 5775 5785 5805 5825 36 38 40 42 44 46 48 52 56 58 60 64 100 104 106 108 112 116 120 124 128 132 136 140 149 153 155 157 161 165 A A A A A A A Not apply Not apply Not apply Not apply Not apply Not apply Not apply Not apply Not apply Not apply Not apply Not apply Not apply Not apply Not apply Not apply Not apply A A A A A A N N N N N N N N N n N N N N N N N N N N N N N N N N N N N N Sincerely Yours, Kyung-Su Han Director, NA Regulatory & Environmental Affairs LG Electronics USA

LG Electronics USA 1000 Sylvan Avenue Englewood Cliffs, New Jersey, United States Date: 2019-08-09 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road, Columbia, MD21046 Attn: Office of Engineering and Technology Subject: Attestation letter regarding UNII client device without radar detection capability FCC ID: BEJIGCJ1PMN To whom it may concern, We, LG Electronics USA, declare that the device for FCC ID: BEJIGCJ1PMN does not support frequency band which not supported by FCC and only support below frequency in all the operational mode(s).

- WiFi Mode/Band 802.11b, g, n / 2.4GHz 802.11a, n, ac / 5GHz Frequency Band (MHz) 2412 ~ 2462 5180~5240 /5745~5825 Mode/Band Classic (BDR/EDR) Frequency Band (MHz) 2402 ~ 2480

- Bluetooth Sincerely Yours, Kyung-Su Han Director, NA Regulatory & Environmental Affairs LG Electronics USA

LGElectronicsUSA 1000SylvanAvenueEnglewoodCliffs,NewJersey,UnitedStates August 9,2019 FederalCommunicationsCommission AuthorizationandEvaluationDivision 7435OaklandMillsRoad, Columbia,MD21046 LETTERFORAUTHORIZATION FCC ID: BEJIGCJ1PMN Towhomitmayconcern:

I, the undersigned, hereby authorize Lab Manager Hyunchae, You (or Jungmin, Yang) and of SGS KoreaCo.,Ltd.andhereafterreferredtoasSGSKorea,toactonourbehalfinallmannersrelatingto applicationforequipmentauthorization,includingsigningofalldocumentsrelatingtothesematters. AnyandallactscarriedoutbyLabManagerHyunchae,You(orJungmin,Yang)ofSGSKoreaCo.,Ltd. onourbehalfshallhavethesameeffectasactsofourown. I,theundersigned,herebycertifythatwearenotsubjecttoadenialoffederalbenefits,that includesFCCbenefits,pursuanttoSection5301oftheAntiDrugAbuseActof1988,21U.S.C. 853(a). InauthorizingSGSKoreaasouragent,westillrecognizethatweareresponsibleto:

a) complywiththerelevantprovisionsofthecertificationprogram;

b) make all necessary arrangements for the conduct of the evaluation, including provision for examiningdocumentationandaccesstoallareas,records(includinginternalauditreports)and personnel for the purposes of evaluation (e.g. testing, inspection, assessment, surveillance, reassessment)andresolutionofcomplaints;

c) makeclaimsregardingcertificationonlyinrespectofthescopeforwhichcertification hasbeengranted;

d) donotuseourproductcertificationinsuchamannerastobringtheCertificationDivisioninto disreputeandnotmakeanystatementregardingourproductcertificationwhichtheCertification Divisionmayconsidermisleadingorunauthorized;

e) uponsuspensionorcancellationofcertification,discontinueuseofalladvertisingmatterthat contains any reference thereto and return any certification documents as required by the Certification Division; LG Electronics USA 1000 Sylvan Avenue Englewood Cliffs, New Jersey, UnitedStates LGElectronicsUSA 1000SylvanAvenueEnglewoodCliffs,NewJersey,UnitedStates f) usecertificationonlytoindicatetheproductsarecertifiedasbeinginconformitywithspecified standards;g)endeavortoensurethatnocertificateorreportnoranypartthereofisusedina misleadingmanner;

h) ensure that any reference to our product certification in communication media such as documents,brochuresoradvertising,complieswiththerequirementsoftheCertificationDivision;

i) keeparecordofallcomplaintsmadeknowntotheusrelatingtotheproductscompliancewith requirementsoftherelevantstandardandtomaketheserecordsavailabletotheCertification Divisionwhenrequested;

j) takeappropriateactionwithrespecttosuchcomplaintsandanydeficienciesfoundinproducts orservicesthataffectcompliancewiththerequirementsforcertification;

k) documenttheactionstaken.Thisauthorizationisvaliduntilfurtherwrittennoticefromthe applicant. SincerelyYours Kyung-Su Han Director, NA Regulatory & Environmental Affairs LG Electronics USA

LG Electronics USA 1000 Sylvan Avenue Englewood Cliffs, New Jersey, United States August 9, 2019 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road, Columbia, MD 21046 Request of Confidentiality FCC ID: BEJIGCJ1PMN To Whom It May Concern:

Pursuant to Sections 0.457 and 0.459 of the Commissions Rules (CFR 47), and Section 552 (b) (4) of the Freedom of Information Act, LG Electronics USA hereby requests confidentiality and treatment of certain information accompanying this application. The materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. We are also hereby request ShortTerm Confidentiality for 180 days after the grant as outlined in Public Notice DA 041705. This provision will give LG Electronics USA temporary confidentiality of commercially sensitive information prior to product release. CONFIDENTIAL LIST Permanent ShortTerm Block Diagram 1 2 Operational Descriptions 3 4 5 6 7 8 Users Manual Schematics Tuneup Procedure External Photos Internal Photos TestSetup Photos The requested Permanent and Temporary Confidential exhibits are listed as follows:

Sincerely Yours KyungSu Han Director, NA Regulatory & Environmental Affairs LG Electronics USA

LG Electronics USA 1000 Sylvan Avenue, Englewood Cliffs, New Jersey, United States, 07632 August 9, 2019 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road, Columbia, MD 21046 LETTER OF DECLARATION FCC IC: BEJIGCJ1PMN We, LG Electronics Inc. as manufacturer of product mentioned above hereby declare similarity of each model as below. Other than the above part and function, all other parts of each product are identical. Sincerely, Kyung-Su Han Director NA Regulatory & Environmental Affairs LG Electronics USA

In accordance with FCC KDB 594280 D02 v01r02, the new Software Security requirements for U-NII Devices, the following information is provided to describe the security features of the software in this device. SOFTWARE SECURITY REQUIREMENTS FOR U-NII DEVICES General Description SOFTWARE SECURITY DESCRIPTION 1 Describe how any software/firmware updates for elements than can affect the devices RF parameters will be obtained, downloaded, validated and installed. For software that is accessed through manufacturers website or devices management system, describe the different levels of security as appropriate 2 Describe the RF parameters that are modified by any software/firmware without any hardware changes. Are these parameters in some way limited such that any other software/firmware changes will not allow the device to exceed the authorized RF characteristics?

3 Describe in detail the authentication protocols that are in place to ensure that the source of the RF-

related software/firmware is valid. Describe in detail how the RF-related software is protected against modification. 4 Describe in detail any encryption methods used to support the use of legitimate RF-related software/firmware. 5 For a device that can be configured as a master and client (with active or passive scanning), explain how the device ensures compliance for each mode? In particular if the device acts as master in some band of operation and client in another; how is compliance ensured in each band of operation?

Third-Party Access Control 1 Explain if any third parties have the capability to operate a U.S.-sold device on any other regulatory domain, frequencies, or in any manner that may allow the device to operate in violation of the devices authorization if activated in the U.S. 2 Describe, if the device permits third-party software or firmware installation, what mechanisms are provided by the manufacturer to permit integration of such functions while ensuring that the RF parameters of the device cannot be operated outside its authorization for operation in the U.S. In the description include what controls and/or agreements are in place with providers of third-party functionality to ensure the devices underlying RF parameters are unchanged and how the manufacturer verifies the functionality. WiFi driver and firmware are embedded in system software and there is no installation and download process. All default parameters approved by the FCC are programmed in driver and firmware which would be embedded in system. So end-user can not access those parameters. WiFi driver and firmware are embedded in system software and there is no installation process. End-user can not access them. No encryption, but WiFi firmware is an binary code. The device is configured as a client only. There is a country code regulatory parameter to limit product to operate the device under its authorization in the U.S. This regulatory parameter would define which channel would be available to operate in passive scan to meet U-NII requirements. The device has a country code regulatory parameter to operate it under its authorization in the U.S. Also, end-user can not access that value. WiFi driver and firmware are embedded in system and there is no installation process. This system software is programmed and protected in flash memory. The third-parties can not access that flash memory. 3 For Certified Transmitter modular devices, describe how the module grantee ensures that host manufacturers fully comply with these software security requirements for U-NII devices. If the module is controlled through driver software loaded in the host, describe how the drivers are controlled and managed such that the modular transmitter RF parameters are not modified outside the grant of authorization. 7 The device has a country code regulatory parameter to operate it under its authorization in the U.S. This regulatory parameter would define which channel would be available to operate in passive scan to meet U-NII requirements. Also, this parameter can not be modified by outside because it is contained in WiFi driver and firmware. USER CONFIGURATION GUIDE 1 Describe the user configurations permitted through the UI. If different levels of access are permitted for professional installers, system integrators or end-users, describe the differences. SOFTWARE CONFIGURATION DESCRIPTION a) What parameters are viewable and configurable by different parties?9 WiFi driver and firmware that can affect the devices RF parameters are embedded in system and there is not any installation process. System firmware is programmed and protected in flash memory. All default parameters are programmed in both driver and firmware which would be embedded in system firmware. End-user only could select which master(AP) to connect. b) What parameters are accessible or modifiable by the professional installer or system integrators?

None.

(1) Are the parameters in some way limited, so that the installers will not enter parameters that exceed those authorized?

Yes. Some parameters are programmed in driver and firmware are embedded in system, and the installer cannot access them. Also, the system firmware protected in flash memory. The professional installer/end-user cannot access the flash memory.

(2) What controls exist that the user cannot operate the device outside its authorization in the U.S.?

There is a country code regulatory parameter to limit user to operate the device outside its authorization in the U.S. c) What parameters are accessible or modifiable by the end-user?

None. End user only could select which master(AP) to connect and input password.

(1) Are the parameters in some way limited, so that the user or installers will not enter parameters that exceed those authorized?

Yes. Some parameters are programmed in driver and firmware are embedded in system, and the installer cannot access them. Also, the system firmware protected in flash memory. The professional installer/end-user cannot access the flash memory.

(2) What controls exist so that the user cannot operate the device outside its authorization in the U.S.?

There is a country code regulatory parameter to limit product to operate the device outside its authorization in the U.S. d) Is the country code factory set? Can it be changed in the UI?

(1) If it can be changed, what controls exist to ensure that the device can only operate within its authorization in the U.S.?

e) What are the default parameters when the device is restarted?

Yes, country code is factory set, and can not be changed in the UI. It can not be changed. There is a country code regulatory parameter to limit product to operate the device outside its authorization in the U.S. All default parameters are programmed in driver and firmware which would be embedded in system firmware. The system firmware is programmed and protected in flash memory. The professional installer/end-user cannot access the flash memory. 2 Can the radio be configured in bridge or mesh mode? If yes, an attestation may be required. Further No. The device can not be configured in both mode. information is available in KDB Publication 905462 D02. 3 For a device that can be configured as a master and client (with active or passive scanning), if this is No, end-user can not configure the WiFi device to be as a master or client. user configurable, describe what controls exist, within the UI, to ensure compliance for each mode. If the device acts as a master in some bands and client in others, how is this configured to ensure compliance?

For a device that can be configured as different types of access points, such as point-to-point or point-to-multipoint, and use different types of antennas, describe what controls exist to ensure compliance with applicable limits and the proper antenna is used for each mode of operation. (See Section 15.407(a)) 4 The device is not a access point.