FCC ID: BEJ70UW340C LED TV Receiver

 

OWNERS MANUAL Safety and Reference Please read this manual carefully before operating your TV and retain it for future reference.

*MFL69412528*

www.lg.com P/NO : MFL69412528 (1610-REV00) Safety Instructions Please read these safety precautions carefully before using the product. WARNING Do not place the TV and/or remote control in the following environments:

A location exposed to direct An area with high humidity such as sunlight a bathroom Near any heat source such as stoves and other devices that produce heat Near kitchen counters or humidifierswheretheycaneasily be exposed to steam or oil An area exposed to rain or wind Near containers of water such as vases Otherwise,thismayresultinfire, electric shock, malfunction or product deformation. Mains Plug is the TV connecting/

disconnecting device to AC mains electric supply.This plug must remain readily attached and operable when TV is in use. Do not touch the power plug with wet hands. Additionally, if the cord pin is wet or covered with dust, dry the power plug completely or wipe dust off.Youmaybeelectrocuteddueto excess moisture. Make sure to connect Mains cable to compliant AC mains socket with Grounded earth pin. (Except for devices which are not grounded on earth.) Otherwise possibility you may be electrocuted or injured. Do not place the product where it might be exposed to dust. This may causeafirehazard. Insert power cable plug completely into wall socket otherwise if not secured completelyintosocket,fireignition may break out. 2 ENGLISH Ensure the power cord does not come into contact with hot objects such as aheater.Thismaycauseafireoran electricshockhazard. Do not drop the product or let it fall over when connecting external devices. Otherwise, this may result in injury or damage to the product. Do not place a heavy object, or the product itself, on power cables. Otherwise,thismayresultinfireor electric shock. Bend antenna cable between inside and outside building to prevent rain fromflowingin.Thismaycausewater damaged inside the Product and could give an electric shock. When mounting TV onto wall make sure to neatly install and isolate cabling from rear of TV as to not createpossibilityofelectricshock/fire hazard. Do not plug too many electrical devices into a single multiple electrical outlet. Otherwise,thismayresultinfiredueto over-heating. Desiccant Keep the anti-moisture packing material or vinyl packing out of the reach of children. Anti-moisture material is harmful if swallowed. If swallowed by mistake, force the patient to vomit and visit the nearest hospital. Additionally, vinyl packing can causesuffocation.Keepitoutofthe reach of children. Do not let your children climb or cling onto the TV. Otherwise, the TV may fall over, which may cause serious injury. Dispose of used batteries carefully to ensure that a small child does not consume them. Please seek Doctor-

Medical Attention immediately if child consumes batteries. 3 ENGLISH Do not insert any metal objects/

conductors (like a metal chopstick/

cutlery/screwdriver) between power cable plug and input Wall Socket while it is connected to the input terminal on the wall. Additionally, do not touch the power cable right after plugging into thewallinputterminal.Youmaybe electrocuted. Do not spray water on the product or scrubwithaninflammablesubstance

(thinnerorbenzene).Fireorelectric shock accident can occur. Do not allow any impact, shock or any objects to fall into the unit, and do not dropanythingontothescreen.You may be injured or the product can be damaged. Donotputorstoreinflammable substances near the product. There is a danger of combustion/explosion orfireduetocarelesshandlingofthe inflammablesubstances. Never touch this product or antenna during a thunder or lighting storm. Youmaybeelectrocuted. Do not drop metallic objects such as coins, hair pins, chopsticks or wire into theproduct,orinflammableobjects such as paper and matches. Children must pay particular attention. Electrical shock,fireorinjurycanoccur.Ifa foreign object is dropped into the product, unplug the power cord and contact the service centre. Never touch the wall outlet when there is leakage of gas, open the windows andventilate.Itmaycauseafireora burn by a spark. Do not disassemble, repair or modify theproductatyourowndiscretion.Fire or electric shock accident can occur. Contact the service centre for check, calibration or repair. 4 ENGLISH If any of the following occur, unplug the product immediately and contact your local service centre. The product has been impacted by The product has been damaged Foreignobjectshaveenteredthe shock product The product produced smoke or a strange smell Thismayresultinfireorelectricshock. Unplug the TV from AC mains wall socket if you do not intend to use the TV for a long period of time. Accumulateddustcancausefire hazardandinsulationdeteriorationcan causeelectricleakage/shock/fire. Apparatus shall not be exposed to dripping or splashing and no objects filledwithliquids,suchasvases,shall be placed on the apparatus. Do not install this product on a wall if it could be exposed to oil or oil mist. This may damage the product and cause it to fall. If water or another substance enters the product (like a AC adapter, power cord, TV), disconnect the power cord and contact the service centre immediately. Otherwise,thismayresultinfireor electric shock. OnlyuseanauthorizedACadapter and power cord approved by LG Electronics. Otherwise, this may result infire,electricshock,malfunctionor product deformation. Never Disassemble the AC adapter or powercord.Thismayresultinfireor electric shock. Handle the adapter carefully to avoid dropping or striking it. An impact could damage the adapter. 5 ENGLISH CAUTION Install the product where no radio wave occurs. There should be enough distance between an outside antenna and power lines to keep the former from touching the latter even when the antenna falls. This may cause an electric shock. Do not install the product on places such as unstable shelves or inclined surfaces. Also avoid places where there is vibration or where the product cannot be fully supported. Otherwise, theproductmayfallorflipover,which may cause injury or damage to the product. If you install the TV on a stand, you need to take actions to prevent the product from overturning. Otherwise, the product may fall over, which may cause injury. If you intend to mount the product to a wall, attach VESA standard mounting interface (optional parts) to the back of the product. When you install the set to use the wall mounting bracket

(optionalparts),fixitcarefullysoas not to drop. Only use the attachments /

accessoriesspecifiedbythe manufacturer. When installing the antenna, consult withaqualifiedservicetechnician.If notinstalledbyaqualifiedtechnician, thismaycreateafirehazardoran electricshockhazard. We recommend that you maintain a distance of at least 2 to 7 times the diagonalscreensizewhenwatching TV. If you watch TV for a long period of time, this may cause blurred vision. 6 ENGLISH Onlyusethespecifiedtypeofbattery. This could cause damage to the remote control. Do not mix new batteries with old batteries. This may cause the batteries to overheat and leak. Batteries should not be exposed to excessiveheat.Forexample,keep away from direct Sunlight , open fireplaceandelectricheaters. Do not place non-rechargeable batteries in charging device. When connecting external devices such as video game consoles, make sure the connecting cables are long enough. Otherwise, the product may fall over, which may cause injury or damage the product. DonotturntheproductOn/Offby plugging-in or unplugging the power plug to the wall outlet. (Do not use the power plug for switch.) It may cause mechanical failure or could give an electric shock. Make sure there are no objects between the remote control and its sensor. Signal from Remote Control can be interrupted due to external/internal lightingegSunlight,fluorescent lighting.Ifthisoccursturnofflighting or darken viewing area. Please follow the installation instructions below to prevent the product from overheating. The distance between the product and the wall should be more than 10 cm. Do not install the product in a place with no ventilation (e.g., on a bookshelf or in a cupboard). Do not install the product on a carpet or cushion. Make sure the air vent is not blocked by a tablecloth or curtain. Otherwise,thismayresultinfire. 7 ENGLISH Do not press strongly upon the panel with a hand or sharp object such as nail, pencil or pen, or make a scratch on it, as it may cause damage to screen. Avoid touching the screen or holding yourfinger(s)againstitforlongperiods of time. Doing so may produce some temporary or permanent distortion/

damage to screen. When cleaning the product and its components,unplugthepowerfirst and wipe it with a soft cloth. Applying excessive force may cause scratches or discolouration. Do not spray with water or wipe with a wet cloth. Never use glass cleaner, car or industrial shiner,abrasivesorwax,benzene, alcohol etc., which can damage the product and its panel. Otherwise, thismayresultinfire,electricshock or product damage (deformation, corrosion or breakage). As long as this unit is connected to the AC wall outlet, it is not disconnected from the AC power source even if you turnoffthisunitbySWITCH. Take care not to touch the ventilation openings when watching the TV for long periods as the ventilation openings may become hot. This does notaffecttheoperationorperformance of the product. Periodically examine the cord of your appliance, and if its appearance indicates damage or deterioration, unplug it, discontinue use of the appliance, and have the cord replaced with an exact replacement part by an authorizedservicer. Prevent dust collecting on the power plug pins or outlet. This may cause a firehazard. Protect the power cord from physical or mechanical abuse, such as being twisted, kinked, pinched, closed in a door, or walked upon. Pay particular attention to plugs, wall outlets, and the point where the cord exits the appliance. Make sure the power cord is connected securely to the power plug on the TV. 8 ENGLISH When unplugging the cable, grab the plug and unplug it, by pulling at the plug. Dont pull at the cord to unplug the power cord from the power board, as thiscouldbehazardous. When moving the product, make sure youturnthepowerofffirst.Then, unplug the power cables, antenna cables and all connecting cables. The TV set or power cord may be damaged,whichmaycreateafire hazardorcauseelectricshock. If the product feels cold to the touch, theremaybeasmallflickerwhenit is turned on. This is normal, there is nothing wrong with product. This panel is an advanced product that containsmillionsofpixels.Youmay see tiny black dots and/or brightly coloured dots (red, blue or green) atasizeof1ppmonthepanel.This does not indicate a malfunction and doesnotaffecttheperformanceand reliability of the product. This phenomenon also occurs in third-

party products and is not subject to exchange or refund. When moving or unpacking the product, work in pairs because the product is heavy. Otherwise, this may result in injury. Referallservicingtoqualifiedservice personnel.Servicingisrequiredwhen the apparatus has been damaged in any way, such as power supply cord orplugisdamaged,liquidhasbeen spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. Youmayfinddifferentbrightnessand color of the panel depending on your viewing position(left/right/top/down). This phenomenon occurs due to the characteristic of the panel. It is not related with the product performance, and it is not malfunction.

* LG LED TVs are LCD TVs with LED backlighting. 9 ENGLISH WARNING!

Never place a television set in an unstable location. A television set may fall, causing serious personal injury or death. Many injuries, particularly to children, can be avoided by taking simple precautions such as:

Using cabinets or stands recommended by the manufacturer of the television set. Only using furniture that can safely support the television set. Ensuring the television set is not overhanging the edge of the supporting furniture. Not placing the television set on tall furniture (for example, cupboards or bookcases) without anchoring both the furniture and the television set to a suitable support. Not placing the television set on cloth or other materials that may be located between the television set and supporting furniture. Educating children about the dangers of climbing on furniture to reach the television set or its controls. If your existing television set is being retained and relocated, the same considerations as above should be applied. Displaying a still image for a prolonged period of time may cause image sticking.Avoiddisplayingafixedimage on the TV screen for a long period of time. Generated sound Crackingnoise:Acrackingnoisethat occurswhenwatchingorturningoff the TV is generated by plastic thermal contraction due to tempera-ture and humidity. This noise is common for products where thermal deformation isrequired.Electricalcircuithumming/

panelbuzzing:Alowlevelnoiseis generated from a high-speed switching circuit, which supplies a large amount of current to operate a product. It varies depending on the product. Thisgeneratedsounddoesnotaffect the performance and reliability of the product. Do not use high voltage electrical goods near the TV (e.g. electric mosquito-swatter).Thismayresultin product malfunction. 10 ENGLISH Symbols Refers to alternating current(AC). Refers to direct current(DC). ReferstoclassIIequipment. Refers to stand-by. RefertoON(power). Refers to dangerous voltage. 1 2 Preparing NOTE IftheTVisturnedonforthefirst time after it was shipped from the factory,initializationoftheTVmay take a few minutes. Imageshownmaydifferfromyour TV. YourTVsOSD(OnScreenDisplay) maydifferslightlyfromthatshown in this manual. The available menus and options maydifferfromtheinputsourceor product model that you are using. New features may be added to this TV in the future. The items supplied with your product may vary depending on the model. Productspecificationsorcontents of this manual may be changed without prior notice due to upgrade of product functions. Foranoptimalconnection,HDMI cables and USB devices should havebezelslessthan10mmthick and 18 mm width. Use an extension cable that supports USB 2.0 if the USB cable or USB memory stick doesnotfitintoyourTVsUSBport. B B A A

*A10mm

*B18mm 11 ENGLISH Lifting and moving the TV Please note the following advice to prevent the TV from being scratched or damaged and for safe transportation regardlessofitstypeandsize. It is recommended to move the TV in the box or packing material that the TV originally came in. Before moving or lifting the TV, disconnect the power cord and all cables. When holding the TV, the screen should face away from you to avoid damage. Hold the top and bottom of the TV framefirmly.Makesurenottohold the transparent part, speaker, or speaker grill area. UseacertifiedcablewiththeHDMI logo attached. IfyoudonotuseacertifiedHDMI cable, the screen may not display or a connection error may occur. Recommended HDMI cable types

(3m or less)

- High-Speed HDMI/ cable

- High-Speed HDMI/ cable with Ethernet CAUTION Do not use any unapproved items to ensure the safety and product life span. Any damage or injuries caused by using unapproved items are not covered by the warranty. Somemodelshaveathinfilm attached on to the screen and this must not be removed. 12 ENGLISH When transporting a large TV, there should be at least 2 people. When transporting the TV by hand, hold the TV as shown in the following illustration. When transporting the TV, do not expose the TV to jolts or excessive vibration. When transporting the TV, keep the TV upright, never turn the TV on its side or tilt towards the left or right. Do not apply excessive pressure tocauseflexing/bendingofframe chassis as it may damage screen. When handling the TV, be careful not to damage the protruding buttons. CAUTION Avoid touching the screen at all times, as this may result in damage to the screen. Do not move the TV by holding the cable holders, as the cable holders may break, and injuries and damage to the TV may occur. (Depending on model) Using the button YoucansimplyoperatetheTV functions, pressing or moving the button. Joystick Button BasicFunctions Power on (Press) PowerOff(Pressandhold)1 Volume Control Programmes Control 1 All running apps will close, and any recording in progress will stop. Adjusting the Menu When the TV is turned on, press the buttononetime.Youcanadjustthe Menu items pressing or moving the buttons. Turnsthepoweroff. Clears on-screen displays and returns to TV viewing. Changes the input source. Accesses the setting menu. 13 ENGLISH Using the kensington se-

curity system Imageshownmaydifferfromyour TV. The Kensington security system connector is located at the rear of the TV.Formoreinformationofinstallation and using, refer to the manual provided with the Kensington security system or visit http://www.kensington.com. Connect the Kensington security system cable between the TV and a table. Mounting on a table 1 Lift and tilt the TV into its upright position on a table. Leave a 10 cm (minimum) space from the wall for proper ventilation. 10 cm 10 cm 0 c m 1 10 cm 10 cm 2 Connect the power cord to a wall outlet. CAUTION Do not place the TV near or on sources of heat, as this may result infireorotherdamage. 14 ENGLISH Securing the TV to a wall Mounting on a wall 1 Insert and tighten the eye-bolts, or TV brackets and bolts on the back of the TV. If there are bolts inserted at the eye-bolts position, remove the bolts first. 2 Mount the wall brackets with the bolts to the wall. Match the location of the wall bracket and the eye-bolts on the rear of the TV. 3 Connect the eye-bolts and wall brackets tightly with a sturdy rope. Make sure to keep the rope horizontalwiththeflatsurface. CAUTION Make sure that children do not climb on or hang on the TV. NOTE Use a platform or cabinet that is strong and large enough to support the TV securely. Brackets, bolts and ropes are not provided.Youcanobtainadditional accessories from your local dealer. Attach an optional wall mount bracket at the rear of the TV carefully and install the wall mount bracket on a solidwallperpendiculartothefloor. When you attach the TV to other building materials, please contact qualifiedpersonnel.LGrecommends that wall mounting be performed by a qualifiedprofessionalinstaller. We recommend the use of LGs wall mount bracket. The LG wall mount is easy to adjust or to connect the cables. When you do not use LGs wall mount bracket, please use a wall mount bracket where the device is adequatelysecuredtothewallwith enough space to allow connectivity to external devices. If you are using a non-adjustable mount, attach the mount to the wall. AttachthecablestotheTVfirst,then attach the TV to the mount. 10 cm 10 cm 10 cm 10 cm Make sure to use screws and wall mount bracket that meet the VESA standard. Standard dimensions for the wall mount kits are described in the following table. 15 ENGLISH Separate purchase

(Wall Mounting Bracket) Model VESA (A x B) Standard screw Number of screws Wall mount bracket 70UW34**

600 x 400 M8 4 LSW640B A B Connections(notifications) Connect various external devices to the TV and switch input modes to select an externaldevice.Formoreinformation of external devices connection, refer to the manual provided with each device. Available external devices are: HD receivers, DVD players, VCRs, audio systems, USB storage devices, PC, gaming devices, and other external devices. NOTE The external device connection maydifferfromthemodel. Connect external devices to the TV regardless of the order of the TV port. If you record a TV program on a DVD recorder or VCR, make sure to connect the TV signal input cable to the TV through a DVD recorder orVCR.Formoreinformationof recording, refer to the manual provided with the connected device. Refertotheexternalequipments manual for operating instructions. If you connect a gaming device to the TV, use the cable supplied with the gaming device. CAUTION Remove the stand before installing the TV on a wall mount by performing the stand attachment in reverse. NOTE When using the wall mount, it is recommended that you apply a piece of tape over the Stand holes to prevent dust and bugs from entering the holes. (Depending on model) Stand hole 16 ENGLISH In PC mode, there may be noise associated with the resolution, vertical pattern, contrast or brightness. If noise is present, change the PC output to another resolution, change the refresh rate to another rate or adjust the brightness and contrast on the PICTURE menu until the picture is clear. In PC mode, some resolution settings may not work properly depending on the graphics card. If Ultra HD content is played on your PC, video or audio may become disrupted intermittently depending on your PCs performance. DTV channels that are broadcast in AVS / AVS + codec does not support recording and time-shifting. Antenna connection Connect the TV to a wall antenna socketwithanRFcable(75). Use a signal splitter to use more than 2 TVs. Iftheimagequalityispoor,installa signalamplifierproperlytoimprove theimagequality. Iftheimagequalityispoorwithan antenna connected, try to realign the antenna in the correct direction. An antenna cable and converter are not supplied. Supported DTV Audio: MPEG, Dolby Digital, Dolby Digital Plus, HE-AAC, DRA. This set can meet insulation requirementbetweenPGandRF network system so you can connect RFcabledirectly. Other connections Connect your TV to external devices. Forthebestpictureandaudioquality, Connect the external device and the TV with the HDMI cable. Some separate cable is not provided. NOTE Useonlywiththe3-pole3.5mm Stereo Jack. Do not connect your headphones or earphones to the port for connecting an external speaker. 17 ENGLISH CAUTION Do not connect a modular phone cable to the LAN port Since there various connection methods, please follow thesepecificationsofyour telecommunication carrier or internet service provider. Wired network connection

(Depending on model) This TV can be connected to a Pro:Centric server via the LAN port. After making the physical connection, the TV needs to be set up for network communication. Connect the LAN port of the Modem or Router from Pro:Centric server to the LAN port on the TV. Broadband Modem Broadband Modem Router Pro:Centric Sever Broadband Modem Pro:Centric Sever Connect the LAN port of the Modem or Router to the LAN port on the TV. Connect the LAN port of the PC to the AUX LAN port on the TV. 18 ENGLISH Remote control The descriptions in this manual are based on the buttons on the remote control. Please read this manual carefully and use the TV correctly. To replace batteries, open the battery cover,replacebatteries(1.5VAAA) matching the ends to the label inside the compartment, and close the battery cover. To remove the batteries, perform the installation actions in reverse. and CAUTION In Analogue TV and some countries, some remote control buttons may not work. Make sure to point the remote control toward the remote control sensor on the TV. A B A TurnstheTVonoroff. Adjusts the brightness of the screen to reduce energy consumption. Shows the previous Changes the input history. source. Selects Radio, TV and DTV programme. B Number buttons Enters numbers. Accesses the saved Tunes to the last channel channel list. viewed. 19 ENGLISH D Coloured buttons These access special functions in some menus.

(

Blue)

:Yellow,

: Green,

: Red,

:

Control buttons for media contents Recalls your preferred subtitle in digital mode. C D Adjusts the volume level. Selects a smart menu. Resizesanimage. C programmes. screen. guide. Mutes all sounds. Scrolls through the saved Moves to the previous or next Shows programme Displays and removes Pro:Centric Application. Views the information of the current programme and screen. Navigation buttons (up/down/left/

right) Scrolls through menus or options. Selects menus or options andconfirmsyourinput. menu. Accesses the main Returns to the previous screen. Clears all on-screen displays and returns to TV viewing. 20 ENGLISH To use HDMI ULTRA HD Deep Colour SETTINGS General ULTRA HD Deep Colour

(1/2/3) ULTRA HD Deep Colour:

HDMI HDMI

- On:Support4K@50/60Hz(4:4:4,

- Off:Support4K@50/60Hz8bit 4:2:2, 4:2:0)

(4:2:0) If the device connected to Input Port also supports ULTRA HD Deep Colour, your picture may be clearer. However, if the device doesnt support it, it may not work properly. In that case, connect the device to adifferentHDMIportorchangethe TVs ULTRA HD Deep Colour setting toOff.

- This feature is available on certain models which are supported ULTRA HD Deep Colour only. Licenses Supportedlicensesmaydifferby model.Formoreinformationabout licenses, visit www.lg.com. Manufactured under license from Dolby Laboratories. Dolby and the double-D symbol are trademarks of Dolby Laboratories. The terms HDMI and HDMI High-

DefinitionMultimediainterface, and the HDMI logo are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries. ForDTSpatents,seehttp://patents. dts.com. Manufactured under license from DTS Licensing Limited. DTS, DTS-HD, the Symbol, & DTS and the Symbol together are registered trademarks of DTS, Inc. DTS, Inc. All Rights Reserved. 21 ENGLISH Open Source Software Notice Information To obtain the source code under GPL, LGPL, MPL, and other open source licenses, that is contained in this product, please visit http://

opensource.lge.com. In addition to the source code, all referred license terms, warranty disclaimers and copyright notices are available for download. LG Electronics will also provide open source code to you on CD-ROM for a charge covering the cost of performing such distribution (such as the cost of media, shipping, and handling) upon emailrequesttoopensource@lge.com. Thisofferisvalidforthree(3)years from the date on which you purchased the product. Supportedfileformat Extenstion Codec

.asf

.wmv

.avi

.mp4

.m4v

.mov

.3gp

.3g2

.mkv Video Audio Video Audio Video Audio Video Audio Video Audio VC-1 Advanced Profile(WMVA excluded), VC-1 Simple and Main Profiles WMA Standard

(WMA v1/ WMA Speech excluded) XViD(except 3 warp-point GMC), H.264/AVC, Motion Jpeg, MPEG-4 MPEG-1 Layer I, II, MPEG-1 Layer III (MP3), Dolby Digital, LPCM, ADPCM, DTS H.264/AVC, MPEG-4, HEVC Dolby Digital, Dolby Digital Plus, AAC, MPEG-1 Layer III (MP3) H.264/AVC, MPEG-4 AAC, AMR-NB, AMR-WB MPEG-2, MPEG-

4, H.264/AVC, VP8, VP9, HEVC Dolby Digital, Dolby Digital Plus, AAC, PCM, DTS, MPEG-1 Layer I, II, MPEG-1 Layer III (MP3) 22 ENGLISH Extenstion Codec SupportedAudioFormats

.ts

.trp

.tp

.mts

.mpg

.mpeg

.dat

.vob

.mkv

.mp4

.ts

.rm/.rmvb Video Audio H.264/AVC, MPEG-2, HEVC MPEG-1 Layer I, II, MPEG-1 Layer III (MP3), Dolby Digital, Dolby Digital Plus, AAC, PCM Video MPEG-1, MPEG-2 MPEG-1 Layer I, II, MPEG-1 Layer III (MP3) Audio Video MPEG-1, MPEG-2 Audio Video Audio Video Audio Dolby Digital, MPEG-1 Layer I, II, DVD-LPCM H.264/AVC, H.265(HEVC) Dolby Digital, Dolby Digital Plus, AAC RV30, RV40 Realaudio6(cook), AAC LC, HE-AAC 32 Kbps - 320 Kbps File Format Item Info

.wav

.mp3 PCM 8Khz-48khz 16KHz-48KHz Bir rate Sample freq. Support MPEG1, MPEG2 Channels Mono, stereo Sample freq. Support Channels Mono, stereo Bir rate Sample freq. Support Channels Mono, stereo Bir rate Sample freq. Support WMA Channels Up to 6 ch The number of supported 8kHz-48kHz 8kHz-48kHz Vorbis

.wma

.ogg 64 Kbps - 320 Kbps programmes may vary depending onthesamplefrequency. 128 Kbps - 320 Kbps 23 ENGLISH Cannot control the TV with the remote control. Check the remote control sensor on the product and try again. Check if there is any obstacle between the product and the remote control. Check if the batteries are still working and properly installed (

to to

).

, No image display and no sound is produced. Check if the product is turned on. Check if the power cord is connected to a wall outlet. Check if there is a problem in the wall outlet by connecting other products. TheTVturnsoffsuddenly. Check the power control settings. The power supply may be interrupted. Check if the Sleep Timer / Timer PowerOffisactivatedinthe TIMERS settings. If there is no signal while the TV is on,theTVwillturnoffautomatically after15minutesofinactivity. When connecting to the PC (HDMI), NosignalorInvalidFormatis displayed. TurntheTVoff/onusingtheremote control. Reconnect the HDMI cable. Restart the PC with the TV on. SupportedPhotoFormats File Format Format Resolution Minimum:

jpeg, jpg, jpe JPEG Maximum:

128 x 128 Normal Type:

15360(W) x 8640 (H) Progressive Type:

1920 (W) x 1440 (H) 64 x 64 png PNG bmp BMP Minimum:

Maximum: 5760(W)x Minimum:

Maximum: 1920 (W) x 5760(H) 64 x 64 1080 (H) Troubleshooting The software may be updated for improvement in performance. The customer is responsible to ensure the compatibilityoftheirequipmentwith any LG Electronics software. If needed, please consult with LG Electronics and update new software versions according to the guidance provided by LG Electronics. 24 ENGLISH Key Codes This feature is not available for all models. 00 01 02 P P

+

03

-

R/C 95 R/C 71 R/C 72 RED/

R/C 79 RATIO GREEN/ R/C R/C R/C ENERGYSAVING INPUT 06 07 08 MUTE 09 10 - 19 *0-9 28 39

(/) R/C 0B

(/) R/C 0C PORTAL R/C 1A Q.VIEW R/C 5B R/C 7C SMART R/C 8E R/C 8F EXIT R/C AA BACK() SUBTITLE

(/

)

(/

) SETTINGS OK LIST

(BLUE/)

(YELLOW/) R/C F0 R/C AB R/C B0 R/C B1 R/C BA R/C B5

(/)

(//) APP TV/RAD 40 41 43 44 53 61 63 INFO R/C GUIDE R/C R/C R/C R/C R/C R/C R/C R/C R/C R/C R/C R/C R/C R/C 25 ENGLISH* Key code 4C (0x4C) is available on ATSC/ISDB models which use major/minor channel.(ForSouthKorea,Japan,NorthAmerica,LatinAmericaexceptColombia models) External Control Device Setup ImageshownmaydifferfromyourTV. Connect the USB to Serial converter/RS-232C input jack to an external control device (such as a computer or an A/V control system) to control the products functions externally. Note:ThetypeofcontrolportontheTVcanbedifferentbetweenmodelseries. Please be advised that not all models support this type of connectivity. Cable is not provided. USB to Serial converter with USB Cable USB Type

(PC) N I B S U

(TV) LGTVsupportsPL2303chip-based(VendorID:0x0557,ProductID:0x2008)

(TV)

(PC) It can be purchased from computer stores that carry accessories for IT RS-232C IN USB to serial converter which is not made nor provided by LG.

(CONTROL & SERVICE) support professionals.

(PC)

(PC) 26 1 3 2 1 3 2 Y L N O E C V R E S I

(TV)

(TV) RS-232C IN

(CONTROL & SERVICE) ENGLISH RS-232C With RS232C Cable DE9 (D-Sub 9pin) Type YouneedtopurchasetheRS-232C(DE9,D-Sub9pinfemale-to-femaletype)

(PC) toRS-232CcablerequiredfortheconnectionbetweenthePCandtheTV, whichisspecifiedinthemanual.

(TV) B S U N I

(PC) RS-232C IN

(CONTROL & SERVICE)

(TV) TheconnectioninterfacemaydifferfromyourTV. 1 3

(PC) Type of connector : D-Sub 9-Pin male Y L N O E C V R E S I 1 6

(PC) 5 9 RS-232CConfigurations 7-WireConfigurations

(Standard RS-232C cable) RXD TXD GND DTR DSR RTS CTS PC TV 3 2 2 3 5 5 6 4 4 6 8 7 8 7 D-Sub 9 D-Sub 9 TXD RXD GND DTR DSR RTS CTS

(TV)

(TV) 2 RS-232C 1

(Serial port) 3 RS-232C IN

(CONTROL & SERVICE) 2 3-WireConfigurations

(Not standard) PC TV

(CONTROL & SERVICE) RXD TXD GND DTR DSR RTS CTS 3 2 RS-232C IN 2 3 5 5 6 4 4 6 8 7 8 7 D-Sub 9 D-Sub 9 TXD RXD GND DTR DSR RTS CTS 27 ENGLISH Set ID ForSetIDnumber,seeReal Data Mapping. 1 Press SETTINGS to access the main menus. 2 Press the Navigation buttons to scroll to (*General About this TV or OPTION) and press OK. 3 Press the Navigation buttons to scroll to SET ID and press OK. 4 Scroll left or right to select a set ID number and select CLOSE. The adjustment range is 1-99. 5 Whenyouarefinished,pressEXIT.

* (Depending on model) Communication Parameters Baud rate : 9600 bps (UART) Data length : 8 bits Parity : None Stop bit : 1 bit Communication code : ASCII code Use a crossed (reverse) cable. 28 ENGLISH Command reference list

(Depending on model) COMMAND1 COMMAND2 k k k 01. Power*

02. Aspect Ratio 03. Screen Mute 04. Volume Mute 05. Volume Control 06. Contrast k k k 07. Brightness k 08. Color/

Colour 09. Tint k k 10. Sharpness k 11. OSD k Select a c d e f g h i j k l DATA

(Hexadecimal) 00 to 01 COMMAND1 COMMAND2 DATA

(Hexadecimal) 12. Remote Control Lock Mode k m 00 to 01

(p.32) 13. Balance k 14. Color

(Colour) Temperature 15. Equalizer 16. Energy Saving 17. Key 18. Control Backlight, Control Panel Light 19. Input select

(Main) 20. Tune Command 21. Channel

(Programme) Add/ Del(Skip) x j j m m x m m

(p.33) 00 to 01 00 to 64 00 to 64 00 to 64 00 to 64 00 to 64 00 to 32 00 to 01 t u v q c g b a b 00 to 64 00 to 64

(p.35) 00to05 Key Codes 00 to 64

(p.36)

(p.37) 00 to 01 29 ENGLISH* Note : During playing or recording media, all commands except Power (ka) and Key (mc) are not executed and treated as NG. WithRS232Ccable,TVcancommunicatekacommandinpower-onor power-off status. but with USB-to-Serial converter cable, the command works only if TV is on. Transmission / Receiving Protocol Transmission

[Command1][Command2][ ][Set ID][ ][Data][Cr]

[Command1]:FirstcommandtocontroltheTV.(j,k,morx)

[Command 2] : Second command to control the TV.

[SetID]:Youcanadjustthe[SetID]tochoosedesiredmonitorIDnumberin option menu. Adjustment range in TV is 1 to 99. If [Set ID] value is selected to 0, every connected set can be controlled.

* [Set ID] is indicated as decimal (1 to 99) on menu and as Hexadecimal

(0x00 to 0x63) on transmission/receiving protocol.

[DATA]:Totransmitcommanddata(hexadecimal).TransmitFFdatatoread status of command.

[Cr] : Carriage Return - ASCII code 0x0D

[ ] : Space ASCII code 0x20 OK Acknowledgement

[Command2][ ][Set ID][ ][OK][Data][x]

* The set transmits ACK (acknowledgement) based on this format when receiv-

ing normal data. At this time, if the data is data read mode, it indicates pres-

ent status data. If the data is data write mode, it returns the data of the PC computer. 30 ENGLISH Error Acknowledgement

[Command2][ ][Set ID][ ][NG][Data][x]

* The set transmits ACK (acknowledgement) based on this format when receiv-

ing abnormal data from non-viable functions or communication errors. Data 00: Illegal Code Real data mapping (Hexadecimal : Decimal)

* When you enter the [data] in hexadecimal, refer to following conversion table.

* Channel Tune (ma) Command uses two-byte hexadecimal value([data]) to select channel number. 00 : Step 0 01 : Step 1 (Set ID 1)

... 0A : Step 10 (Set ID 10)

... 0F:Step15(SetID15) 10 : Step 16 (Set ID 16)

... 32:Step50(SetID50) 33:Step51(SetID51)

... 63 : Step 99 (Set ID 99)

... C7 : Step 199 C8 : Step 200

... FE:Step254 FF:Step255

... 0100:Step256

... 27 0E : Step 9998 270F:Step9999

... 31 ENGLISH* Commands may work differently depending on model and signal. 01. Power (Command: k a) TocontrolPower*OnorOffofthe 02. Aspect Ratio (Command: k c)

(MainPictureSize) To adjust the screen format. (Main picture format) Youcanalsoadjustthescreen format using the Aspect Ratio in the PICTURE menu. Transmission [k][c][ ][Set ID][ ]

[Data][Cr]

Data 01 : Normal screen (4:3)

(JustScanOff) 02 : Wide screen (16:9)

(JustScanOff) 09 : Just Scan 06 : Original

(JustScanoff) Ack [c][ ][Set ID][ ][OK/NG][Data]

[x]

* Using the PC input, you select either 16:9 or 4:3 screen aspect ratio. set. Transmission[k][a][ ][Set ID][ ]

[Data][Cr]

Data00:PowerOff 01 : *Power On Ack [a][ ][Set ID][ ][OK/NG][Data]

[x]

ToShowTVisPowerOnor*Off Transmission [k][a][ ][Set ID][ ]

[FF][Cr]

Ack [a][ ][Set ID][ ][OK][Data][x]

* Similarly, if other functions transmit FFdatabasedonthisformat,Ac-

knowledgement feedback presents status about each function. 32 ENGLISH 03. Screen Mute (Command: k d) Toselectscreenmuteon/off. Transmission [k][d][ ][Set ID][ ]

[Data][Cr]

Data00:Screenmuteoff(Pictureon) Videomuteoff 01:Screenmuteon(Pictureoff) 10 : Video mute on Ack [d][ ][Set ID][ ][OK/NG][Data]

[x]

* In case of video mute on only, TV will display On Screen Display(OSD). But, in case of Screen mute on, TV will not display OSD. 04. Volume Mute (Command: k e) Tocontrolvolumemuteon/off. Youcanalsoadjustmuteusingthe MUTE button on remote control. Transmission [k][e][ ][Set ID][ ]

[Data][Cr]

Data00:Volumemuteon(Volumeoff) 01:Volumemuteoff(Volumeon) Ack [e][ ][Set ID][ ][OK/NG][Data]

[x]

05.Volume Control (Command: k f) To adjust volume. Youcanalsoadjustvolumewiththe volume buttons on remote control. Transmission [k][f][ ][Set ID][ ]

[Data][Cr]

Data Min : 00 to Max : 64 Ack [f][ ][Set ID][ ][OK/NG][Data]

[x]

06. Contrast (Command: k g) To adjust screen contrast. Youcanalsoadjustcontrastinthe PICTURE menu. Transmission [k][g][ ][Set ID][ ]

[Data][Cr]

Data Min : 00 to Max : 64 Ack [g][ ][Set ID][ ][OK/NG][Data]

[x]

07. Brightness (Command: k h) To adjust screen brightness. Youcanalsoadjustbrightnessinthe PICTURE menu. Transmission [k][h][ ][Set ID][ ]

[Data][Cr]

Data Min : 00 to Max : 64 Ack [h][ ][Set ID][ ][OK/NG][Data]

[x]

33 ENGLISH 08. Color/Colour (Command: k i) To adjust the screen Color(Colour). Youcanalsoadjustcolourinthe PICTURE menu. Transmission [k][i][ ][Set ID][ ]

[Data][Cr]

Data Min : 00 to Max : 64 Ack [i][ ][Set ID][ ][OK/NG][Data]

[x]

11. OSD Select (Command: k l) To select OSD (On Screen Display) on/offwhencontrollingremotely. Transmission [k][l][ ][Set ID][ ]

[Data][Cr]

Data00:OSDoff 01 : OSD on Ack [l][ ][Set ID][ ][OK/NG][Data]

[x]

09. Tint (Command: k j) To adjust the screen tint. YoucanalsoadjusttintinthePIC-

TURE menu. Transmission [k][j][ ][Set ID][ ]

[Data][Cr]

Data Red : 00 to Green : 64 Ack [j][ ][Set ID][ ][OK/NG][Data]

[x]

10. Sharpness (Command: k k) To adjust the screen sharpness. Youcanalsoadjustsharpnessinthe PICTURE menu. Transmission [k][k][ ][Set ID][ ]

[Data][Cr]

Data Min : 00 to Max : 32 Ack [k][ ][Set ID][ ][OK/NG][Data]

[x]

12. Remote control lock mode (Com-

mand: k m) To lock the front panel controls on the monitor and remote control. Transmission [k][m][ ][Set ID][ ]

[Data][Cr]

Data00:Lockoff 01 : Lock on Ack [m][ ][Set ID][ ][OK/NG]

[Data][x]

* If you are not using the remote con-

trol, use this mode. Whenmainpowerisoff&on

(plug-offandplug-in,after20-30 seconds), external control lock is released.

* Inthestandbymode(DCoffbyoff timer or ka, mc command), and if key lock is on, TV will not turn on by power on key of IR & Local Key. 34 ENGLISH 13. Balance (Command: k t) To adjust balance. Youcanalsoadjustbalanceinthe AUDIO menu. Transmission [k][t][ ][Set ID][ ]

[Data][Cr]

Data Min : 00 to Max : 64 Ack [t][ ][Set ID][ ][OK/NG][Data]

[x]

14. Color(Colour) Temperature (Com-

mand: x u) Toadjustcolourtemperature.You can also adjust Color(Colour) Tem-

perature in the PICTURE menu. Transmission [x][u][ ][Set ID][ ]

[Data][Cr]

Data Min : 00 to Max : 64 Ack [u][ ][Set ID][ ][OK/NG][Data]

[x]

15.Equalizer(Command:jv) AdjustEQoftheset. Transmission [j][v][ ][Set ID][ ]

[Data][Cr]

MSB 0 0 0 0 0 0 0 LSB 0 Data 4 3 2 1 0 Step 0 0 0 0 0 0 0 0 0 1 0(de-

cimal) 1(de-

cimal) Frequency 7 6 5 Frequ-

ency 0 0 0 1st Band 0 0 1 2nd Band 0 1 0 3rd Band 0 1 1 4th Band 1 0 0 5th Band

... .. .. .. .. .. 1 0 0 1 1 19(de-

cimal) 1 0 1 0 1 20(de-

cimal) Ack [v][ ][Set ID][ ][OK/NG][Data]

[x]

* It depends on model, and can adjust whensoundmodeisEQadjustable value. 35 ENGLISH 16. EnergySaving(Command:jq) To reduce the power consumption of theTV.YoucanalsoadjustEnergy Saving in PICTURE menu. Transmission[j][q][][SetID][]

[Data][Cr]

Data 00:Off 01 : Minimum 02 : Medium 03 : Maximum 04:Auto(ForLCDTV/LEDTV)/

Intelligentsensor(ForPDPTV) 05:Screenoff

* (Depending on model) Ack[q][][SetID][][OK/NG][Data]

[x]

17. Key (Command: m c) To send IR remote key code. Transmission [m][c][ ][Set ID][ ]

[Data][Cr]

DataKeycode-p.25 Ack [c][ ][Set ID][ ][OK/NG][Data]

[x]

18. Control Backlight, Control Panel Light (Command: m g) ForLCDTV/LEDTV To control the backlight. Transmission [m][g][ ][Set ID][ ]

[Data][Cr]

Data Min : 00 to Max : 64 Ack [g][ ][Set ID][ ][OK/NG][Data]

[x]

19. Input select (Command: x b)

(Main Picture Input) To select input source for main picture. Transmission [x][b][ ][Set ID][ ]

[Data][Cr]

Data 00 : DTV 02 : Satellite DTV ISDB-BS (Japan) 03 : ISDB-CS1 (Japan) 04 : ISDB-CS2 (Japan) 11 : CATV 20 : AV or AV1 40 : Component1 60 : RGB 90 : HDMI1 92 : HDMI3 01 : CADTV 10 : ATV 21 : AV2 41 :

Component2 91 : HDMI2 93 : HDMI4 Ack [b][ ][Set ID][ ][OK/NG][Data]

[x]

* This function depends on model and signal. 36 ENGLISH 20. Tune Command (Command: m a)

* Thiscommandmayworkdifferently depending on model and signal. ForEurope,Mid-East,Colombia, Asia except South Korea and Japan Model Select channel to following physical number. Transmission [m][a][ ][Set ID][ ]

[Data 00][ ][Data 01][ ][Data 02]

[Cr]

* Analog Antenna/Cable

[Data 00][Data 01] Channel Data Data 00 : High byte channel data Data 01 : Low byte channel data

- 00 00 ~ 00 C7 (Decimal : 0 ~ 199) Data 02 : Input Source (Analog)

- 00 : Antenna TV (ATV)

- 80 : Cable TV (CATV)

* Digital Antenna/Cable/Satellite

[Data 00][Data 01]: Channel Data Data 00 : High Channel data Data 01 : Low Channel data

-0000~270F(Decimal:0~9999) Data 02 : Input Source (Digital)

- 10 : Antenna TV (DTV)

- 20 : Antenna Radio (Radio)

- 40 : Satellite TV (SDTV)

-50:SatelliteRadio(S-Radio)

- 90 : Cable TV (CADTV)

- a0 : Cable Radio (CA-Radio)

* Tune Command Examples:

1. Tune to the Analog antenna (PAL) Channel 10. Set ID = All = 00 Data 00 & 01 = Channel Data is 10 =

00 0a Data 02 = Analog Antenna TV = 00 Result = ma 00 00 0a 00 2. Tune to the digital antenna (DVB-T) Channel 01. Set ID = All = 00 Data 00 & 01 = Channel Data is 1 =

00 01 Data 02 = Digital Antenna TV = 10 Result = ma 00 00 01 10 3. Tune to the satellite (DVB-S) Channel 1000. Set ID = All = 00 Data 00 & 01 = Channel Data is 1000

= 03 E8 Data 02 = Digital Satellite TV = 40 Result = ma 00 03 E8 40 Ack [a][ ][Set ID][ ][OK][Data 00]

[Data 01][Data 02][x][a][ ][Set ID]

[ ][NG][Data 00][x]

37 ENGLISH* Digital Antenna/Cable Data 00 : xx (Dont care)

[Data 01][Data 02]: Major Channel Number Data 01 : High byte Channel Data Data 02 : Low byte Channel Data

-0001~270F(Decimal:1~9999)

[Data 03][Data 04]: Minor Channel Number Data 03 : High byte Channel Data Data 04 : Low byte Channel Data Data05:InputSource(Digital)

- 02 : Antenna TV (DTV) Use Physi-

cal Channel Number

- 06 : Cable TV (CADTV) Use Physi-

cal Channel Number

- 22 : Antenna TV (DTV) Dont Use Physical Channel Number

- 26 : Cable TV (CADTV) - Dont Use Physical Channel Number

- 46 : Cable TV (CADTV) Use Physi-

cal/Major Channel Number Only

(One Part Channel)

- 66 : Cable TV (CADTV) Use Major Channel Number Only (One Part Chan-

nel) Two bytes are available for each major and minor channel data, but usually the low byte is used alone (high byte is 0). ForSouthKorea,North/Latin America except Colombia Model To tune channel to following physi-

cal/major/minor number. Transmission [m][a][ ][0][ ][Data00]

[ ][Data01][ ][Data02][ ][Data03][ ]

[Data04][][Data05][Cr]

Digital channels have a Physical, Major, and Minor channel number. The Physical number is the actual digital channel number, the Major is the num-

ber that the channel should be mapped to, and the Minor is the sub-channel. Since the ATSC tuner automatically maps the channel from the Major /

Minor number, the Physical number is notrequiredwhensendingacommand in Digital.

* Analog Antenna/Cable Data 00 : Physical Channel Number

-Antenna(ATV):02~45(Decimal:2~

69)

- Cable (CATV) : 01, 0E~7D (Decimal :

1,14~125)

[Data 01 ~ 04]: Major/Minor Channel Number Data 01 & 02: xx (Dont care) Data 03 & 04: xx (Dont care) Data05:InputSource(Analog)

- 00 : Antenna TV (ATV)

- 01 : Cable TV (CATV) 38 ENGLISH* Tune Command Examples:

1. Tune to the Analog cable (NTSC) channel35. Set ID = All = 00 Data00=ChannelDatais35=23 Data 01 & 02 = No Major = 00 00 Data 03 & 04 = No Minor = 00 00 Data05=AnalogCableTV=01 Total = ma 00 23 00 00 00 00 01 2. Tune to the digital antenna (ATSC) channel 30-3. Set ID = All = 00 Data 00 = Dont know Physical = 00 Data 01 & 02 = Major is 30 = 00 1E Data 03 & 04 = Minor is 3 = 00 03 Data05=DigitalAntennaTV=22 Total = ma 00 00 00 1E 00 03 22 Ack [a][ ][Set ID][ ][OK][Data 00]

[Data 01][Data 02][Data 03][Data 04][Data05][x][a][][SetID][]

[NG][Data 00][x]

ForJapanModel To tune channel to following physi-

cal/major/minor number. Transmission [m][a][ ][0][ ]

[Data00][ ][Data01][ ][Data02][ ]

[Data03][][Data04][][Data05][Cr]

* Digital Antenna/Satellite Data 00 : xx (Dont care)

[Data 01][Data 02]: Major Channel Number Data 01 : High byte Channel Data Data 02 : Low byte Channel Data

-0001~270F(Decimal:1~9999)

[Data 03][Data 04]: Minor/Branch Channel Number

(Dont care in Sat-

ellite) Data 03 : High byte Channel Data Data 04 : Low byte Channel Data Data05:InputSource(Digital/Satellite for Japan)

- 02 : Antenna TV (DTV)

- 07 : BS (Broadcasting Satellite)

- 08 : CS1 (Communication Satellite 1)

- 09 : CS2 (Communication Satellite 2) 39 ENGLISH 21. Channel(Programme) Add/Del(Skip)

(Command: m b) To skip current channel(programme) for next time. Transmission [m][b][ ][Set ID][ ]

[Data][Cr]

Data 00 : Del(ATSC,ISDB)/

Skip(DVB) 01 : Add Ack [b][ ][Set ID][ ][OK/NG][Data]

[x]

Set the saved channel status to del(ATSC, ISDB)/ skip(DVB) or add.

* Tune Command Examples:

1 Tune to the digital antenna (ISDB-T) channel 17-1. Set ID = All = 00 Data 00 = Dont know Physical = 00 Data 01 & 02 = Major is 17 = 00 11 Data 03 & 04 = Minor/Branch is 1 =

00 01 Data05=DigitalAntennaTV=02 Total = ma 00 00 00 11 00 01 02 2. Tune to the BS (ISDB-BS) channel 30. Set ID = All = 00 Data 00 = Dont know Physical = 00 Data 01 & 02 = Major is 30 = 00 1E Data 03 & 04 = Dont Care = 00 00 Data05=Digital BS TV = 07 Total = ma 00 00 00 1E 00 00 07

* This feature is varied based on the model. Ack [a][ ][Set ID][ ][OK][Data 00]

[Data 01][Data 02][Data 03][Data 04][Data05][x][a][][SetID][]

[NG][Data 00][x]

40 ENGLISH Specifications Digital TV Television System DTMB, DVB-C Programme Coverage DTMB:1~62 DVB-C:52.5MHz~

866MHz Analogue TV PAL D/K/B/G/I, NTSC-M PALD/K:VHF/UHF 1 ~ 62, CATV 1~41 PALB/G/I:VHF/

UHF1~69,CATV1

~ 47 NTSCM:VHF/UHF2

~ 78, CATV 1 ~ 71 Maximum number of storable programmes External Antenna Impedance Environment condition 420 75 Operating Temperature Operating Humidity Storage Temperature Storage Humidity 0Cto45C Less than 80 %

-20 C to 60 C Lessthan85%

CMIITID:2015AJ5419 41 ENGLISH 28.12 33.72 33.75 26.97 27.00 33.71 33.75 56.25 67.43 67.50 53.95 54.00 56.25 61.43 67.50 112.50 135.00 135.00 53.95 54.00 56.25 61.43 67.50 112.50 135.00 135.00 50.00 59.94 60.00 23.97 24.00 29.97 30.00 50.00 59.94 60.00 23.98 24.00 25.00 29.97 30.00 50.00 59.94 60.00 23.98 24.00 25.00 29.97 30.00 50.00 59.94 60.00 HDMI (PC) supported mode

(Use HDMI IN 1 for PC mode) Resolution 640x350 720 x 400 640 x 480 800 x 600 1024 x 768 1152x864 1360 x 768 1280 x 1024 1920 x 1080 3840 x 2160 4096 x 2160 Horizontal Frequency

(kHz) 31.46 31.46 31.46 37.87 48.36 54.34 47.71 63.98 67.50 67.50 56.25 54.00 53.95 54.00 Vertical Frequency

(Hz) 70.09 70.08 59.94 60.31 60.00 60.05 60.01 60.02 60.00 30.00 25.00 24.00 23.97 24.00 1920 x 1080 3840 x 2160 HDMI (DTV) supported mode 4096 x 2160 Resolution 640 x 480 720 x 480 720x576 1280 x 720 Horizontal Frequency

(kHz) 31.46 31.50 31.47 31.50 31.25 44.96 45.00 37.50 Vertical Frequency

(Hz) 59.94 60.00 59.94 60.00 50.00 59.94 60.00 50.00 42 ENGLISH Component port connecting information Component ports on Y PB PR the TV Video output ports on DVD player Y PB PR Y B-Y B-Y Y Cb Cr Y Pb Pr Signal 480i/576i 480p/576p 720p / 1080i 1080p Component O O O O

(Only50Hz/60 Hz) 43 ENGLISH Important Safety Instructions 1) Read these instructions. 2) Keep these instructions. 3) Heed all warnings. 4) Follow all instructions. 5) Do not use this apparatus near water. 6) Clean only with dry cloth. 7) Do not block any ventilation openings. Install in accordance with the manufacturer's instructions. 8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. 10) Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. 11) Only use attachments/accessories specified by the manufacturer. 12) Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. 13) Unplug this apparatus during lightning storms or when unused for long periods of time. 14) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. Regulatory Information cont. FCC Compliance Statement respecte toutes les exigences du Rglement sur le matriel brouilleur du Canada. NOTICE The regulations are applied only to the products with the ID LABEL indicating specific requirements. This equipment has been tested and found to comply within the limits of a Class B digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception (which can be determined by turning the equipment on and off), the user is encouraged to try to correct the interference by using one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and the receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Caution: Changes or modifications not expressly approved by the party responsible for compliance could void the user's (or your) authority to operate the equipment. Only peripherals (digital input/output devices, terminals, printers, etc.) certified to comply with the Class B limits may be attached to this monitor. Operation with non-certified peripherals is likely to result in interference to radio and TV reception. Only shielded signal cables may be used with this System. NOTICE The regulations are applied only to the products with the ID LABEL indicating specific requirements. Canadian DOC Notice This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. Cet appareil numrique de la classe B 1