FCC ID: BEJTM13LNNAHK1 LTE Module

Technical Specification

(TM13LNNAHK1) 1/10 History Ver. 1.0 Date 2018.06.12 Contents Written by Checked by Approved by Note 2/10 Contents 1. Product Introduction ...................................................................................................... 4 1.1 Block Diagram ...................................................................................................... 5 1.2 Environmental Specifications ............................................................................... 5 1.3 Electrical Specifications ....................................................................................... 5 1.3.1 Absolute Maximum and ESD Ratings ........................................................... 5 1.3.2 Current Consumption .................................................................................... 6 1.4 Mechanical Specifications .................................................................................. 6 1.4.1 Physical Dimensions and Connection Interface ............................................ 6 1.4.2 Mechanical Drawing ...................................................................................... 7 2. Pin Definitions ............................................................................................................... 8 3 RF Specification ............................................................................................................. 9 3.1. LTE B2,B4, B5, B13 Specification ....................................................................... 9 3.2. CDMA BC0, BC1 Specification.. 10 3/10 1. Product Introuction The TM13LNNAHK1 are designed for the automotive industry. They support LTE and CDMA air Interface standards. The TM13LNNAHK1 are based on the Qualcomm MDM9628 wireless chipsets and support the following bands. Table 1. Supported Band US Region LTE B2/B4/B5/B13 Band CDMA BC0/BC1 1.1 Block Diagram Figure 1.1. TM13LNNAHK1 Block diagram 4/10 1.2 Environmental Specifications The environmental specification for operating and storage of the TM13LNNAHK1 are defined in the the table below. Table 2. Environmental Specifications Parameter Operating Temperature Storage Temperature Humidity Temperature Range

-40 to 85

-40 to +90 95% or less 1.3 Electrical Specifications This section provides details for some of the key electrical specifications of the TM13LNNAHK1 embedded modules. 1.3.1 Absolute Maximum Rating and ESD Ratings This section defines the Absolute Maximum and Electrostatic Discharge (ESD) Ratings of the TM13LNNAHK1 embedded modules. Warning: If these parameters are exceeded, even momentarily, damage may occur to the device. Table 3. Absolute Maximum Ratings Parameter

+4.0_VPWR Power Supply Input VIN ESD Ratings ESD1) Voltage on any digital input or output pin VREG_MDME+0.5 Max 4.4V Units Min V V kV 10

-

-

-

Primary, Diversity antenna pads Contact 1) The ESD Simulator configured with 330pF, 2000. Caution: The TM13LNNAHK1 embedded modules are sensitive to Electrostatic Discharge. ESD countermeasures and handling methods must be used when handling the TM03LNNAHK0 devices. 5/10 1.3.2 Current Consumption Table 4. TM13LNNAHK1 Current Consumption (TBD) Mode Parameter Band2/4/13, Max TX Output /Full RB Band5, Max TX Output /Full RB 800MHz 1900MHz Idle, Registered Idle, Registered Sleep Mode, Average Current Sleep Mode, Average Current LTE CDMA LTE CDMA LTE CDMA Typical Max 650 600 550 600 600 550 650 600 1.8 2.2 2.2 1.8 2.2 1.8 1.8 2.2 Units mA mA mA mA mA mA 1.4 Mechanical Specifications 1.4.1 Physical Dimensions and Connection Interface The TM13LNNAHK1 embedded modules are a Land Grid Array (LGA) form factor device. The device does not have a System or RF connectors. All electrical and mechanical connections are made via the 323 pad TM13LNNAHK1 on the underside of the PCB. Table5. TM13LNNAHK1 Embedded Module Dimensions Parameter Overall Dimension Overall Module Height PCB Thickness Flatness Specification Weight Max 34.35 x 40.35 3.85 1.1 0.1 TBD Nominal 34 x 40 3.5 1.0 12 Units mm mm mm mm g 6/10 1.4.2 Mechanical Drawing 1.4.2.1 Module PCB 40 mm 34 2. Pin Definitions 2.1 PIN Definitions HMC_MDM9628 module_Pinmap.xls 7/10 3. RF Specification The specifications for the LTE and CDMA interfaces are defined. TM13LNNAHK1 is designed to be compliant with the standard shown in the table below. Table20. Standards Compliance Technology LTE CDMA 3.1 LTE B2,B4, B5, B13 Specification 3.1.1 LTE TX Output Power The Maximum / Minimum Transmitter Output Power of the TM13LNNAHK1 are specified in the following table. Table21. Conducted TX (Transmit) Max output Power Tolerances LTE Bands Standards 3GPP Release 8 3GPP2 Release IxEVDO, REV.H BAND BAND2 UE Maximum Output Power BAND4 UE Maximum Output Power BAND5 UE Maximum Output Power BAND13 UE Maximum Output Power Method (UL CH) Measure Max and Min and Min Transmit Power of Low Channel (18650) Measure Max and Min Transmit Power of Mid Channel (18900) Measure Max and Min Transmit Power of High Channel (19150) Measure Max and Min and Min Transmit Power of Low Channel (20000) Measure Max and Min Transmit Power of Mid Channel (20175) Measure Max and Min Transmit Power of High Channel (20350) Measure Max and Min and Min Transmit Power of Low Channel (20450) Measure Max and Min Transmit Power of Mid Channel (20525) Measure Max and Min Transmit Power of High Channel (20600) Specification Max Power : 20.3~25.7dBm Min Power : -39dBm Max Power : 20.3~25.7dBm Min Power : -39dBm Max Power : 20.3~25.7dBm Min Power : -39dBm Max Power : 20.3~25.7dBm Min Power : -39dBm Max Power : 20.3~25.7dBm Min Power : -39dBm Max Power : 20.3~25.7dBm Min Power : -39dBm Max Power : 20.3~25.7dBm Min Power : -39dBm Max Power : 20.3~25.7dBm Min Power : -39dBm Max Power : 20.3~25.7dBm Min Power : -39dBm Measure Max and Min Transmit Power of Mid Channel (23230) Max Power : 20.3~25.7dBm Min Power : -39dBm 3.1.2 LTE RX Sensitivity The Receiver Sensitivity of the TM13LNNAHK1 are specified in the following table. Table22. Conducted RX (Receive) Sensitivity LTE Bands 8/10 BAND Method (DL CH) BAND2 Reference sensitivity level(DUAL) BAND4 Reference sensitivity level(DUAL) BAND5 Reference sensitivity level(DUAL) BAND13 Reference sensitivity level(DUAL) Measure BLER of Low Channel (18650) Measure BLER of Mid Channel (18900) Measure BLER of High Channel (19150) Measure BLER of Low Channel (20000) Measure BLER of Mid Channel (20175) Measure BLER of High Channel (20350) Measure BLER of Low Channel (20450) Measure BLER of Mid Channel (20525) Measure BLER of High Channel (20600) Measure BLER of Low Channel (23230) Specification sensitivity : -95 BLER : 5%

sensitivity : -95 BLER : 5%

sensitivity : -95 BLER : 5%

sensitivity : -97 BLER : 5%

sensitivity : -97 BLER : 5%

sensitivity : -97 BLER : 5%

sensitivity : -95 BLER : 5%

sensitivity : -95 BLER : 5%

sensitivity : -95 BLER : 5%

sensitivity : -94 BLER : 5%

3.2 CDMA 800/1900 Specification 3.2.1 CDMA TX Output Power The Maximum Transmitter Output Power of the TM13LNNAHK1 are specified in the following table. Table23. Conducted TX (Transmit) Max output Power Tolerances CDMA Bands Item CDMA800 Power Level PCS1900 Power Level Method (DL CH) Measure Max Transmit Power of Low Channel

(CH=384) in CDMA Mode Measure Max Transmit Power of Middle Channel

(CH=779) in CDMA Mode Measure Max Transmit Power of High Channel

(CH=1013) in CDMA Mode Measure Max Transmit Power of Low Channel

(CH=25) in DCS1900 Mode Measure Max Transmit Power of Middle Channel

(CH=600) in DCS1900 Mode Measure Max Transmit Power of High Channel

(CH=1175) in DCS1900 Mode Specification Max Power : 23~30dBm Max Power : 23~30dBm Max Power : 23~30dBm Max Power : 23~30dBm Max Power : 23~30dBm Max Power : 23~30dBm 3.2.2 CDMA RX Sensitivity The Receiver Sensitivity of the TM13LNNAHK1 are specified in the following table. Table24. Conducted RX (Receive) Sensitivity CDMA Bands 9/10 Item Method (DL CH) Measure BER of Low Channel (CH=384) in EGSM Mode Measure BER of Middle Channel (CH=779) in EGSM Mode Measure BER of High Channel (CH=1013) in EGSM Mode Measure BER of Low Channel (CH=25) in PCS1900 Mode Measure BER of Middle Channel (CH=600) in PCS1900 Mode Measure BER of High Channel (CH=1175) in PCS1900 Mode CDMA800 BER(Bit Error Rate) PCS1900 BER(Bit Error Rate) Specification 0.5% @-104dBm 0.5% @-104dBm 0.5% @-104dBm 0.5% @-104dBm 0.5% @-104dBm 0.5% @-104dBm 10/10 FCC Warning Statement FCC Part 15.19 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Part 15.21 Any changes or modifications (including the antennas) to this device that are not expressly approved by the manufacturer may void the users authority to operate the equipment. Please notice that if the FCC identification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: Contains FCC ID : BEJTM13LNNAHK1 any similar wording that expresses the same meaning may be used. Manual Information to the End User The module is limited to OEM installation ONLY. The OEM integrator is responsible for ensuring that the end-user has no manual instruction to remove or install module. The module is limited to installation in mobile application;

A separate approval is required for all other operating configurations, including portable configurations with respect to Part 2.1093 and difference antenna configurations. There is requirement that the grantee provide guidance to the host manufacturer for compliance with Part 15B requirements.

222 LG-ro Jinwi-myeon, Pyeongtaek-si, Gyeonggi-do, 451-713, Korea. LG Electronics Inc. 28 August 2021 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 FCC Class II Permissive Change for FCC ID: BEJTM13LNNAHK1 This is to request a Class II permissive change for FCC ID: BEJTM13LNNAHK1, originally granted on March 10, 2017. Please refer to schematic difference for the both version file for more detailed information. The summarized change filed under this application is:

FCC : LTE Band 2(BC1) Duplexer change by EOL Company change and size change

Changed the outer size (2.0mm*1.6mm 1.8mm*1.4mm) and the PIN LAND is different, so the PCB is modified Changed the PCB part number: EAX68048402 EAX68048412 Band2 Duplex: Broadcom Wisol The PCB are the same in the U.S. and Canada. And we changed the part number simultaneously while changing the PCB and PCB Company due to the Duplexer change (different size). For more detailed changes, Please see page 2. 222 LG-ro Jinwi-myeon, Pyeongtaek-si, Gyeonggi-do, 451-713, Korea. LG Electronics Inc. 1) The requirements of 2.1043 are fulfilled, i.e., the devices block functions for the fundamental frequency, primary modulator circuit, maximum power, or field strength ratings shall remain unchanged. -> Yes, the devices block functions for the fundamental frequency, primary modulator circuit, maximum power, or field strength ratings of this product does not change. 2) Transmitter PCB layout and parts changes are only permitted if there is no change in identifying a devices form, functional specification, as initially granted or previously approved under a Class II permissive change.

-> Yes, all of the device's form and functional specification are same as the initially graned model. 3) PCB changes are limited to non-substantive modifications layout changes to the same size physical circuit board previously granted.

-> Module PCB has not been changed but, Duplexer size is a little bit smaller than before. 4) C2PCPX is not permitted to add, remove, augment, or change capabilities, such as transmitters, increased bandwidth, additional rule parts, bands, etc.

-> Yes, this product has not added, removed, augmented, or changed capabilities, such as transmitters, increased bandwidth, additional rule parts, and bands 222 LG-ro Jinwi-myeon, Pyeongtaek-si, Gyeonggi-do, 451-713, Korea. LG Electronics Inc. 5) In the PAG submission for item C2PCPX, the applicant shall provide complete information on testing demonstrating that the proposed changes for fundamental emissions are unchanged within the normal, acceptable tolerances and out-of-band; emissions do not exceed the appropriate limits. The PAG submission shall include all applicable test reports and internal photos.

->As a result of comparing the Radiated power in 2018/2021, there is no significant difference as follows and it is within the allowable tolerance category Max power difference (2018-2021) 2018 2021 2021

- 2018 2018 2021 2021

- 2018 Conducted Max Conducted Radiated Max Radiated Power(dBm) Variation(dB) Power(dBm) Variation(dB) 24.68 24.24

-0.44 24.45 23.44

-1.01 23.93 23.42

-0.51 25.71 24.73

-0.98 FCC CDMA BC1 LTE 2 6) The modified device shall not be marketed under the existing grant of certification before confirmation that the C2PCPX PAG is approved and granted.

-> Yes, we will not sell it according to the existing certification until the approval of the PAG is completed. 7) Software Defined Radio (SDR) grants that use the C2PCPX procedure are not permitted to make subsequent Class III permissive changes.

->Not Applicable. 8) The C2PCPX PAG procedure has no impact on the provisions of V) of this publication for non-SDR software-only changes; thus, adding an equipment class when related to rule changes is still permitted.

-> Not Applicable. 9) Class I permissive changes are not permitted3 under this C2PCPX procedure.

-> Yes, Our product will proceed with C2PC. 222 LG-ro Jinwi-myeon, Pyeongtaek-si, Gyeonggi-do, 451-713, Korea. LG Electronics Inc.

*Conclusion: The device is still in compliance with the part 15 rule, then a Class II application is required. Sincerely Yours, Name/Title : Sung Soo Kim / Director, NA Regulatory & Environmental Affairs Company Name : LG Electronics Inc

LG Electronics USA 111 Sylvan Avenue, North Building, Englewood Cliffs, New Jersey, United States, 07632 Sep. 8, 2021 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road, Columbia, MD 21046 REQUEST FOR CONFIDENTIALITY FCC ID: BEJTM13LNNAHK1 Pursuant to Sections 0.457 and 0.459 of the Commissions Rules (CFR 47), and Section 552 (b) (4) of the Freedom of Information Act, LG Electronics USA hereby requests confidentiality and treatment of certain information accompanying this application. The materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. We are also hereby request Short-Term Confidentiality for 180 days after the grant as outlined in Public Notice DA 04-1705. This provision will give LG Electronics USA temporary confidentiality of commercially sensitive information prior to product release. The requested Permanent and Temporary Confidential exhibits are listed as follows:

CONFIDENTIAL LIST Permanent 1 2 Schematics Part List Short-Term 3 4 5 External Photos Internal Photos Test-Setup Photos The Applicant understands that pursuant to Rule 0.457, disclosure of this application and all accompanying documentations, where applicable, will not be made public before the date of the Grant for this application. Sincerely Yours Sung Soo Kim Director, NA Regulatory & Environmental Affairs LG Electronics USA

SGS North America Inc. 620 Old Peachtree Road SUITE 100 Suwanee, Georgia 30024 United States Applicant Declaration Applicant Legal Business Name LG Electronics USA Address Grantee Code FCC ID 111 Sylvan Ave, North Building, Englewood Cliffs, NJ 07632 United States BEJ BEJTM13LNNAHK1 Authorized Contact Name Sung Soo Kim Contact Email Contact Phone sungsoo.kim@lge.com 201-816-2215 I, the undersigned, certify that I am an authorized signatory for the Applicant and therefore declare;

a) b) c) d) e) in accordance with 47CFR2.911(d), all of the statements herein and the exhibits attached hereto are true and correct to the best of my knowledge and belief. in accepting a Grant of Equipment Authorization issued by a TCB, under the authority of the FCC, as a result of the representations made in this application, the Applicant is responsible for:

labeling the equipment with the exact FCC ID as specified in this application,

(1)

(2) compliance statement labeling pursuant to the applicable rules,

(3) compliance of the equipment with the applicable technical rules, if the Applicant is not the actual manufacturer of the equipment, appropriate arrangements have been made with the manufacturer to ensure that production units of this equipment will continue to comply with the FCCs technical requirements. in accordance with 47 CFR 2.909 and KDB394321, the Applicant has read, understood and agrees to accept that they are the responsible party and agree to abide by their responsibilities as specified under 47 CFR 2.909 and KDB394321. in accordance with ISO17065, FCC KDB641163, FCC KDB610077, KDB394321 and RSP-100, the Applicant has read, understood, accepts and agrees to abide by the post market surveillance requirements.

(1)

(2)

(3) the Applicant understands, accepts and agrees that a sample may be requested for surveillance testing. the Applicant shall make provisions to always have a production sample available upon request by SGS, FCC and/or ISED. the Applicant shall, upon request by SGS, at the Applicants expense, provide a production sample of the requested product to SGS, FCC and/or ISED as instructed. The sample shall include all support devices, cables, software, accessories or other hardware or software required for evaluation, review, certification and audit surveillance of products certified by SGS. f) neither the Applicant nor any party to the application is subject to a denial of Federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862 because of a conviction for possession or distribution of a controlled substance. See 47CFR 1.2002(b) for the definition of a party for these purposes. g) the Applicant has read, understood, accepts and agrees to abide by the SGS North America, Inc.(TCB) terms and conditions. Link to CFRs: https://www.fcc.gov/wireless/bureau-divisions/technologies-systems-and-innovation-division/rules-regulations-title-47 Link to KDBs: https://apps.fcc.gov/oetcf/kdb/index.cfm Link to RSP-100: https://www.ic.gc.ca/eic/site/smt-gst.nsf/eng/sf01130.html Applicant Signature:

Date: Sep. 8, 2021 Print Name:

Title:

*NOTE: This declaration cannot be signed by an Agent, it shall be signed by an authorized person listed in the FCC database Sung Soo Kim Director, Regulatory and Environmental Affairs Applicant Declaration Rev:0.0

LG Electronics USA 111 Sylvan Avenue, North Building, Englewood Cliffs, New Jersey, United States, 07632 September 8, 2021 FederalCommunicationsCommission AuthorizationandEvaluationDivision 7435OaklandMillsRoad, Columbia,MD21046 LETTERFORAUTHORIZATION FCC ID: BEJTM13LNNAHK1 Towhomitmayconcern:

I,theundersigned,herebyauthorizeSGS KoreaCo.,Ltd. andhereafterreferredtoasSGS Korea,toactonourbehalfinallmannersrelatingtoapplicationforequipmentauthorization, includingsigningofalldocumentsrelatingtothesematters.Anyandallactscarriedoutby SGSKoreaCo., Ltd.onourbehalfshallhavethesameeffectasactsofourown. I, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includesFCCbenefits,pursuanttoSection5301oftheAntiDrugAbuseActof1988,21U.S.C. 853(a). InauthorizingSGSKoreaasouragent,westillrecognizethatweareresponsibleto:

a) complywiththerelevantprovisionsofthecertificationprogram;

b) makeallnecessaryarrangementsfortheconductoftheevaluation,includingprovision forexaminingdocumentationandaccesstoallareas,records(includinginternalaudit reports) and personnel for the purposes of evaluation (e.g. testing, inspection, assessment,surveillance,reassessment)andresolutionofcomplaints;

c) makeclaimsregardingcertificationonlyinrespectofthescopeforwhichcertification hasbeengranted;

d) do not use our product certification in such a manner as to bring the Certification Divisionintodisreputeandnotmakeanystatementregardingourproductcertification whichtheCertificationDivisionmayconsidermisleadingorunauthorized;

e) upon suspension or cancellation of certification, discontinue use of all advertising matter that contains any referencethereto and returnanycertification documents as requiredbytheCertificationDivision;

f) usecertificationonlytoindicatetheproductsarecertifiedasbeinginconformitywith specifiedstandards;

g) endeavor to ensure that no certificate or report nor any part thereof is used in a misleadingmanner;

h) ensurethatanyreferencetoourproductcertificationincommunicationmediasuchas documents, brochures or advertising, complies with the requirements of the CertificationDivision;

LG Electronics USA 111 Sylvan Avenue, North Building, Englewood Cliffs, New Jersey, United States, 07632 i) j) keep a record of all complaints made known to the us relating to the products compliance with requirements of the relevant standard and to make these records availabletotheCertificationDivisionwhenrequested;

takeappropriateactionwithrespecttosuchcomplaintsandanydeficienciesfoundin productsorservicesthataffectcompliancewiththerequirementsforcertification;

k) documenttheactionstaken. Thisauthorizationisvaliduntilfurtherwrittennoticefromtheapplicant. SincerelyYours Sung Soo Kim Director, NA Regulatory & Environmental Affairs LG Electronics USA