60PY2DRUA PDP Display Users Manual Part 1

 

PLASMA TV OWNERS MANUAL MODELS: TU-50PY22/TU-50PY2DR-UA TU-60PY22/TU-60PY2DR-UA R TruSurround XT TM Please read this manual carefully and completely before operating your TV. Retain this manual for future reference. Record model number and serial number of the TV in the spaces provided below. See the label attached on the back cover and relate this information to your dealer if you require service. Model Number :

Serial Number :

LG Electronics U.S.A., Inc. Warning/Caution WWarning/Caution arning/Caution

/CAUTION WARNING RISK OF ELECTRIC SHOCK DO NOT OPEN WARNING/CAUTION:

TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated dangerous voltage within the products enclosure that may be of suffi-

cient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appli-

ance. WARNING/CAUTION:

TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. FCC NOTICE A Class B digital device This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help. Any changes or modifications not expressly approved by the party responsible for compli-

ance could void the users authority to operate the equipment. CAUTION:

Do not attempt to modify this product in any way without written authorization from LG Electronics. Unauthorized mod-

ification could void the users authority to operate this product. COMPLIANCE:

The responsible party for this products compliance is:

LG Electronics U.S.A., Inc 1000 Sylvan Avenue, Englewood Cliffs, NJ 07632 1-201-816-2000 http://www.lgusa.com WARNING/CAUTION TO REDUCE THE RISK OF FIRE AND ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. 2 Plasma TV TV Guide On Screen Notices for U.S.A. TV Guide On Screen Notices for U.S.A. In the United States, the TV Guide On Screen system and other related marks are registered marks of Gemstar-TV Guide On Screen system International, Inc. and/or one of its affiliates. In Canada,TV Guide On Screen system is a registered mark of Transcontinental Inc., and is used under license by Gemstar-TV Guide On Screen system International, Inc. The TV Guide On Screen system is manufactured under license from Gemstar-TV Guide On Screen system International, Inc. and/or one of its affiliates. The TV Guide On Screen system is protected by one or more of the following issued United States patents 6,498,895, 6,418,556, 6,331,877; 6,239,794; 6,154,203; 5,940,073; 4,908,713; 4,751,578; 4,706,121. Use of the CableCARDTM TradeMark. CableCARDTM is a trademark of Cable Television Laboratories, Inc. Digital Cable Compatibility Digital Cable Compatibility This digital television is capable of receiving basic analog, digital basic and digital premium cable television programming by direct connection to a cable system providing such programming. A security card provided by your cable operator is required to view encrypted digital programming. Certain advanced interactive digital cable services such as video-on-demand, cable operator enhanced program (For example, electronic program guide provided by the cable operator), and data enhanced television service may require the use of a set top box. For more information contact your local cable operator. Owners Manual 3 Warning/Caution Safety Instructions Safety Instructions IMPORTANT SAFETY INSTRUCTIONS Important safety instructions shall be provided with each apparatus. This information shall be given in a separate booklet or sheet, or be located before any operating instructions in an instruction for installation for use and supplied with the appa-

ratus. This information shall be given in a language acceptable to the country where the apparatus is intended to be used. The important safety instructions shall be entitled Important Safety Instructions. The following safety instructions shall be included where applicable, and, when used, shall be verbatim as follows. Additional safety information may be included by adding statements after the end of the following safety instruction list. At the manufacturers option, a picture or drawing that illustrates the intent of a specific safety instruction may be placed immediately adjacent to that safety instruction :

1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturers instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including ampli-

fiers)that produce heat. 9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong, The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. 10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. 11. Only use attachments/accessories specified by the manufacturer. 12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. PORTABLE CART WARNING 4 Plasma TV Safety Instructions 13. Unplug this apparatus during lightning storms or when unused for long periods of time. 14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has exposed to rain or moisture, does not operate normally, or has been dropped. 15. CAUTION concerning the Power Cord :

Most appliances recommend they be placed upon a dedicated circuit; that is, a single outlet circuit which powers only that appliance and has no additional outlets or branch circuits. Check the specification page of this owner's manual to be certain. Do not overload wall outlets. Overloaded wall outlets, loose or damaged wall outlets, extension cords, frayed power cords, or damaged or cracked wire insulation are dangerous. Any of these conditions could result in electric shock or fire. Periodically examine the cord of your appliance, and if its appearance indicates damage or deterioration, unplug it, discontinue use of the appliance, and have the cord replaced with an exact replacement part by an authorized servicer. Protect the power cord from physical or mechanical abuse, such as being twisted, kinked, pinched, closed in a door, or walked upon. Pay particular attention to plugs, wall outlets, and the point where the cord exits the appliance. 16. Outdoor Use Marking :

WARNING - To Reduce The Risk Of Fire Or Electric Shock, Do Not Expose This Appliance To Rain Or Moisture. 17. Wet Location Marking :

Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be placed on the apparatus. Owners Manual 5 Contents Contents Contents Warning/Caution . 2 Digital Cable Compatibility . 3 Safety Instructions . 4~5 Introduction Controls . 8 Connection Options . 9 Remote Control Key Functions . 10~11 Installation Install the RING SPACER with the bolts on the set as . shown . 12 Installation Instructions . 13~15 Remove or Attache the Plate Cover . 13 Joining the TV assembly to the wall to protect the set tum-

bling . 14 Swivel function . 15 Arrangement wires . 15 External Equipment Connections . 16~21 Antenna or Cable Connection . 16~17 VCR Setup . 17 External A/V Source Setup . 18 DVD Setup . 18 CableCARDTM Setup . 19 HDSTB Setup . 19 PC Setup . 21 Monitor Out Setup . 21 Digital Audio Output . 21 HDMI/DVI (VIDEO) . 22~24 TV Guide On Screen Setup . 25~33 Operation Screen Setup for PC mode Adjustments for screen Position, Size, and Phase . 34 Turning the TV On . 35 Home Menu Recorded TV . 36~37 Using the Memory Card . 38~40 Photo List . 41~42 Music list . 43~45 TV Guide On Screen System . 46~66 IEEE 1394 . 67~75 Setup Menu Options On-screen Menus Language Selection . 76 EZ Scan (Channel Search) . 77 Manual Scan . 77 Channel Edit . 78 DTV Signal Strength . 78 Channel Label Setup . 79 Main Picture Source Selection . 79 Aux.Label . 79 Video Menu Options EZ Picture . 80 Manual Picture Control (Off Option) . 80 Color Temperature Control . 80 Video Reset . 80 Audio Menu Options Audio Language . 81 EZ SoundRite / EZ Sound . 81 Manual Sound Control (custom Option) . 82 Front Surround . 82 TV Speakers On/Off Setup . 83 Stereo/SAP Broadcasts Setup . 83 BBE . 83 Time Menu Options Auto Clock Setup . 84 Manual Clock Setup . 84 On/Off Timer Setup . 84 Sleep Timer / Auto Off . 85 Option Menu Features Advanced . 86 Timeshift Mode . 86~87 Recording . 88~90 Cinema 3:2 Mode Setup . 91 Low Power . 91 LG Logo . 92 Aspect Ratio Control . 93 Caption . 94 Caption / Text . 94 Caption Option

. 95 ISM Method . 96 Front LED (Light Emitting Diode) Display . 96 Auto Demo . 97 Lock Menu Options CableCARDTM Function Parental Lock Setup . 99 Cable menu options . 100 Scrambled channel . 100 Cable Channel List . 101 Emergency Alert Message . 101 Remote Control PIP (Picture-in-Picture)/Twin Picture . .102 Watching PIP/POP/Twin Picture . .102 Selecting an Input Signal Source for PIP/Twin Picture .102 Swapping PIP/Twin Picture . 102 TV Program Selection for PIP . 102 Moving the PIP sub picture . 103 Adjusting Main and Sub Picture Sizes for Twin Picture .103 POP (Picture-out-of-Picture: Channel Scan) . 103 Information . 104 EZ Mute . 105 External Control Device Setup . 106~111 IR Codes . 112~113 Programming the Remote . 114 Programming Codes . 115~116 Troubleshooting Checklist . 117 Maintenance . 118 Product Specifications . 119 Warranty . 120~121 6 Plasma TV After reading this manual, keep it handy for future reference. Introduction Introduction Introduction What is a Plasma Display Panel (PDP)?

A plasma display panel is the latest display technology and the best way to achieve flat panel displays with excellent image quality and large screen sizes that are easily viewable. The PDP can be thought of as a descendant of the neon lamp and it can be also be viewed as a series of fluorescent lamps. How does it work?

PDP is an array of cells, known as pixels, which are comprised of 3 sub pixels, corresponding to the colors red, green, and blue. Gas in a plasma state is used to react with phosphors in each sub-pixel to produce colored light (red, green, or blue). These phos-

phors are the same types used in Cathode Ray Tube (CRT) devices such as televisions and common computer monitors. You get the rich, dynamic colors that you expect. Each sub-pixel is individually controlled by advanced electronics to produce over 16 million different colors. All of these mean that you get perfect images that are easily viewable in a display that is less than 5 inches thick. 160 - Wide angle range of vision Your flat panel plasma screen offers an exceptionally broad viewing angle -- over 160 degrees. This means that the display is clear and visible to viewers anywhere in the room who can see the screen. Wide Screen The screen of the Plasma Display is so wide that your viewing experience is as if you are in a theater. Multimedia Connect your plasma display to a PC and you can use it for conferencing, games, and Internet browsing. The Picture-in-Picture feature allows you to view your PC and video images simultaneously. Versatile The light weight and thin size makes it easy to install your plasma display in a variety of locations where conventional TVs will not fit. The PDP Manufacturing Process: a few minute colored dots may be present on the PDP screen The PDP (Plasma Display Panel), which is the display device of this product, is composed of 0.9 to 2.2 million cells. A few cell defects will normally occur in the PDP manufacturing process. Several tiny, minute colored dots visible on the screen should be acceptable. This also occurs in other PDP manufacturers' products. The tiny dots appearing does not mean that this PDP is defec-

tive. Thus a few cell defects are not sufficient cause for the PDP to be exchanged or returned. Our production technology mini-

mizes these cell defects during the manufacture and operation of this product. Cooling Fan Noise In the same way that a fan is used in a PC computer to keep the CPU (Central Processing Unit) cool, the PDP is equipped with cooling fans to cool the Monitor and improve its reliability. Therefore, a certain level of noise could occur while the fans are operat-

ing and cooling the PDP. The fan noise doesn't have any negative effect on the PDP's efficiency or reliability. The noise from these fans is normal during the operation of this product. We hope you understand that a certain level of noise from the cooling fans is acceptable and is not suffi-

cient cause for the PDP to be exchanged or returned. Owners Manual 7 Introduction Controls Controls

- This is a simplified representation of front panel. Here shown may be somewhat different from your TV. Front Panel Controls Front Panel Controls CHANNEL Buttons VOLUME Buttons MENU Button TV/VIDEO Button TV GUIDE Button POWER Button INDEX Switches LED Display on or off. Remote Control Sensor Power Indicator Blinks orange in standby mode, blinks green when the TV is turned on.

(After orange stop the blinking,direct-

ly turn on the TV, but in case of green, screen is displayed at 3~4 minutes later. If power isnt turn on in red, contact your service center.) 8 Plasma TV Connection Options Connection Options Introduction Back Connection Panel Back Connection Panel FRONT A/V INPUT O E D V S

I O E D V I O N O M

L I O D U A R R S-VIDEO Input A connection available to provide bet-

ter picture quality than the video input. VIDEO Input Connects the video signal from a video device. AUDIO Input Use to connect to hear stereo sound from an external device. DVD/DTV Input

(Component 1-

2) Connect a DVHS, a MicroMV Camcorder, or a Set-Top Box to one of IEEE1394 con-

nectors. Remote Control Port Connect your wired remote control here. S-Video Input Connect S-

Video out from an S-VIDEO device. Antenna Input Connect antenna signals to the TV, either directly or through your cable box. RS-232C INPUT

(CONTROL/SERVICE) VIDEO INPUT AUDIO INPUT DVD

/DTV INPUT L R VIDEO L AUDIO R COMPONENT 2 COMPONENT 1 MONITOR OUTPUT A/V INPUT1

(MONO) DIGITAL AUDIO (OPTICAL) RGB INPUT AUDIO INPUT S V I D E O R C E M O T E O N T R O L CABLE ANTENNA AC INPUT I 1 E 3 E 9 E 4 HDMI 2 HDMI /DVI OUTPUT COMPONENT2 INPUT DVI INPUT RS-232C INPUT

(CONTROL/SER-

VICE) PORT Connect to the RS-

232C port on a PC. IEEE1394 Connect DVHS or MicroMV to IEEE1394 Connector. RGB/AUDIO INPUT Connect the moni-

tor output connec-

tor from a PC to the appropriate input port. RS-232C INPUT

(CONTROL/SERVICE) Cable G-LINK Connect an IR controller to this jack. CableCARD Used for CableCARD received Cable Service Provider. IEEE-1394 HDMI 2 HDMI /DVI OUTPUT COMPONENT2 INPUT DVI INPUT VIDEO AUDIO VIDEO AUDIO L R L R COMPONENT INPUT 2 MONITOR OUTPUT AC INPUT DIGITAL AUDIO (OPTICAL) RGB INPUT AUDIO INPUT DVD

/DTV INPUT COMPONENT INPUT 1

(MONO) A/V INPUT 1 S-VIDEO REMOTE CONTROL CABLE ANTENNA HDMI1/DVI(VIDE O), HDMI 2 Connect a HDMI signal to HDMI1/DVI or HDMI2. Or DVI(VIDEO) sig-

nal to HDMI1/DVI port with DVI to HDMI cable. Digital Audio (DVI:

Digital Visual Interface/Compon ent2) Input/

Digital Audio Output Connect digital audio from various types of equipment. Note: In standby mode, these ports will not work. Audio/Video Input Connect audio/video output from an exter-

nal device to these jacks. Monitor Output Connect a second TV or Monitor. CABLE Input Connect cable signals to the TV, either directly or through your cable box. Power Cord Socket This TV operates on an AC power. The voltage is indicated on the Specifications page. Never attempt to operate the TV on DC power.

- This manual explains the features available on the TU-50PY22 series TVs. Owners Manual 9 Introduction Remote Control Key Functions Remote Control Key Functions

- When using the remote control, aim it at the remote control sensor on the TV. POWER Turns your TV or any other programmed equipment on or off, depending on mode. TV INPUT TV/VIDEO X STUDIO Bring up the HOME menu to the screen. MODE D A Y

DAY +

THUMBSTICK (Up/Down/Left/Right/ENTER) Allows you to navigate the on-screen menus and adjust the system settings to your pref-

erence. REC LIST Appear the thumbnail recorded list. VOLUME UP/DOWN Increases/decreases the sound level. NUMBER buttons RATIO Changes the aspect ratio. FLASHBK VCR/DVD BUTTONS Control some video cassette recorders or DVD players.

("RECORD" button is not available for DVD players.)

< Only TV mode >

In Photo mode of Xstudio, the view state changes to the slide show state with PLAY button and the slide show state changes to the view state with PAUSE button. In Music mode of Xstudio, controls the music with PAUSE, STOP, PLAY, (Left/Right) SKIP buttons. Note that FF and REW do not work in the mode. Control the DVHS or Camcorder of IEEE 1394 mode. DAY+/DAY-

Moves forward or backward in 24 hour increments in the Listings Grid. CHANNEL UP/DOWN Selects available channels found with EZ scan. PAGE UP/PAGE DOWN Moves from one full set of screen information to the next one. APM CC AUTO DEMO M/C EJECT EZ SOUND Selects the sound appropriate for the program's character. ATM Concurrently, compare with the Daylight, Normal, Night Time.and Custom on the screen. SAP Selects MTS sound: Mono, Stereo, and SAP in Analog mode. Change the audio language in DTV mode. CC Select a closed caption:

Off, CC1~4, Text1~4. M/C EJECT When removing the Memory Card, this button is used. LIGHT Illuminates the remote control buttons. 10 Plasma TV TV INPUT When you watch the TV, Antenna and Cable is toggled. In Video, Front Video, Component 1-2, RGB-DTV (or RGB-PC), HDMI1/DVI, HDMI2 and IEEE1394 input sources, screen return to the last TV chan-

nel. MODE Selects the remote operating mode: TV, DVD, VCR, AUDIO, CABLE or STB. Select other operating modes, for the remote to operate external devices. MENU Brings up the main menu to the screen. Enters or exits a Panel Menu in the TV Guide On Screen system. EXIT Clears all on-screen displays and returns to TV viewing from any menu. MUTE Switches the sound on or off.(Refer to p.79) TIMER Lets you select the amount of time before your TV turns itself off automatically. ADJUST Adjusts screen position, size, and phase in PC mode. APM CC AUTO DEMO M/C EJECT EZ PIC Adjusts the factory preset picture depending on the viewing environment. AUTO DEMO Displays the slide show to explain the main features of this TV. TV INPUT TV/VIDEO MODE D A Y

DAY +

Introduction TV/VIDEO When you watch the TV, screen return to the last external (Video1-2, Component 1-

2, RGB-DTV (or RGB-PC), HDMI1/DVI, HDMI2) input. Selects: Video 1-2, Component 1-2, RGB-DTV (or RGB-PC), HDMI1/DVI and HDMI2 input sources.

(Only when the jack connects , Video 1-2, Component 1-2 input sources are linked automatically) TV GUIDE Brings up the TV Guide On Screen sys-

tem to the screen. INFO When you watch the TV, information dis-

plays on top of the screen. Not available in Component 1-2, RGB, HDMI1/DVI and HDMI2 mode.(Refer to p.78) Mark Selects the wanted functions. FAV Scroll the Favorite channels. FLASHBK FLASHBK Tunes to the last channel viewed. PIP Switches between PIP, POP (Picture-out-

of-Picture) and Twin picture modes. Switches the video window locking or unlocking in the Listings Grid. PIPCH-/PIPCH+

Changes to next higher/lower PIP chan-

nel. PIP INPUT Selects the input source for the sub pic-

ture. SWAP Exchanges the main/sub images in PIP/Twin picture mode. Installing Batteries Installing Batteries Open the battery compartment cover on the back side and install the batteries matching correct polarity (+ with +, - with -). Install two 1.5V AA batteries. Dont mix old or used batteries with new ones. Replace cover. Owners Manual 11 Installation Installation Installation Accessories Accessories Ensure that the following accessories are included with your plasma display. If an accessory is missing, please contact the dealer where you purchased the product. T V IN P U T M E O D 1.5V 1 . 5 V Y +

A D DAY -

F L A S H B K A P M AUTO DE M O C C Owners Manual Batteries Remote Control Power Cord 2-TV brackets 2-Wall brackets 4-TV bracket bolts(50) 2-TV bracket bolts(60) D-sub 15 pin Cable 75 Round Cable 6-RING SPACER

(Only TU-60PY22 series ) 6-Wall mounting bracket bolts

(Only TU-60PY22 series ) G-LINK Cable Installation Instructions Installation Instructions Joining the TV assembly to the wall to protect the set tumbling TV assembly to the wall to protect the set tumbling Joining the

- Secure the TV assembly by joining it to a wall by using the TV/Wall brackets. After the set must be mounted on the desk top, install the TV brackets on the TV as shown. Install the TV brackets on the TV as shown. Insert the 2 bolts and tighten securely, in the upper holes on the bracket. Install the wall brackets on the wall with 4 bolts*, (not supplied with the product), as shown. Match the height of the TV brackets and the wall brack ets. Check to be sure the brackets are tightened securely. Secure the TV assembly to the wall with strong strings or wound wire cables, (not supplied with the product), as shown. 12 Plasma TV GROUNDING Ensure that you connect the grounding / earth wire to prevent possible electric shock. If grounding methods are not possible, have a qualified electrician install a separate circuit breaker. Do not try to ground the unit by connecting it to telephone wires, lightening rods, or gas pipes. Installation Power Supply Short-circuit Breaker The TV can be installed in various ways such as on a wall, or on a desktop etc. The TV is designed to be mounted horizontally. WWall Mount: Horizontal installation all Mount: Horizontal installation Desktop Pedestal Installation Desktop Pedestal Installation For proper ventilation, allow a clearance of 4 on each side and 2 from the wall. Detailed installation instruc-

tions are available from your dealer, see the optional Wall Mounting Bracket Installation and Setup Guide. For proper ventilation, allow a clearance of 4 on each side and the top, 2.36 on the bottom, and 2 from the wall. Detailed installation instructions are included in the optional Desktop Stand Installation and Setup Setup Guide available from your dealer. 4 inches 2 inches 4 inches 2 inches 4 inches 4 inches 4 inches 4 inches 4 inches 2.36 inches Install the RING SPACER with the bolts on the set as shown. Install the RING SP ACER with the bolts on the set as shown.(Only TU-60PY22 series ) 2. When you connect the wall mounting bracket to the set, connect to it by using the bolts,

(supplied with the product), as shown. 1. Put the RING SPACER in the holes of the bolts before connecting to the wall mounting bracket. Owners Manual 13 Installation Remove or Attache the Plate Cover Attache the Plate Cover Remove or

- When moving or connecting the power cord, be used the these methods.

- And after removing the plate cover, you must install the wall brackets on the wall. RS-232C INPUT

(CONTROL/SERVICE) VIDEO INPUT AUDIO INPUT DVD

/DTV INPUT L R VIDEO L AUDIO R COMPONENT 2 COMPONENT 1 MONITOR OUTPUT A/V INPUT1

(MONO) S V I D E O R E M O T E C O N T R O L DIGITAL AUDIO (OPTICAL) RGB INPUT AUDIO INPUT CABLE ANTENNA AC INPUT I E E E 1 3 9 4 HDMI 2 HDMI /DVI OUTPUT COMPONENT2 INPUT DVI INPUT 1. With hands, push the lower left/right of plate cover and then pull out to the front. 2. Connect the power cord on the TVs back. 3. In attaching the plate cover, firstly you set projection of the GUIDE to BUSHING RUBBER of the upper left/right. Push and put the plate cover with hands. 14 Plasma TV Installation Swivel function Swivel function After installing the TV, you can adjust the the TV set manually to the left or right direction by 20 degrees to suit your viewing position. Note: Before adjusting the angle, you must loosen (to the left) the shaft bolt on the middle of stands back. And when stand be level with TV, you must close (to the right) the shaft bolt to set the hole.(As shown below) 50 60 50 20 Arrangement wires Arrangement wires Run the accessory device wires and power cord inside the JACK MANAGEMENT pole as shown. RS-232C INPUT

(CONTROL/SERVICE) VIDEO INPUT AUDIO INPUT DVD

/DTV INPUT L R VIDEO L AUDIO R COMPONENT 2 COMPONENT 1 MONITOR OUTPUT A/V INPUT1

(MONO) S V I D E O R E M O T E C O N T R O L DIGITAL AUDIO (OPTICAL) RGB INPUT AUDIO INPUT CABLE ANTENNA AC INPUT I E E E 1 3 9 4 HDMI 2 HDMI /DVI OUTPUT COMPONENT2 INPUT DVI INPUT Owners Manual 15 Installation External Equipment Connections External Equipment Connections Antenna or Cable Connection Antenna or Cable Connection 1. Analog and Digital TV signals provided on antenna

- Wall Antenna Socket or Outdoor Antenna without a Cable Box Connections

- For optimum picture quality, adjust antenna direction if needed. Multi-family Dwellings/Apartments

(Connect to wall antenna socket) Wall Antenna Socket AC INPUT Bronze Wire CABLE ANTENNA RF Coaxial Wire (75 ohm) VHF Antenna UHF Antenna Turn clockwise to tighten. Outdoor Antenna Single-family Dwellings /Houses

(Connect to wall jack for outdoor antenna) Bronze Wire Be careful not to bend the bronze wire when connecting the antenna. 2. Analog and Digital TV signals provided on cable Cable TV Wall Jack Turn clockwise to tighten. RF Coaxial Wire (75 ohm) AC INPUT Bronze Wire CABLE ANTENNA 16 Plasma TV 3. Analog and Digital TV signals provided on cable and antenna Antenna Bronze Wire RF Coaxial Wire (75 ohm) Installation Cable TV Wall Jack Turn clockwise to tighten. AC INPUT RF Coaxial Wire (75 ohm) CABLE ANTENNA ANTENNA Bronze Wire In a poor signal area to improve picture quality, purchase and install a signal amplifier. If the antenna needs to be split for two TVs, install a 2-

Way Signal Splitter in the connections. If the antenna is not installed properly, contact your deal-

er for assistance. Signal Amplifier Note: The TV will let you know when the analog, cable, and digital channel scans are complete. VCR Setup VCR Setup

- To avoid picture noise (interference), leave an adequate distance between the VCR and TV

- Use the ISM Method (on the Option menu) feature to avoid having a fixed image remain on the screen for a long period of time. If the 4:3 picture format is used; the fixed images on the sides of the screen may remain visible on the screen. Connection Option 1 Set VCR output switch to 3 or 4 and then tune TV to the same channel number. Connection Option 2 1. Connect the audio and video cables from the VCR's output jacks to the TV input jacks, as shown in the figure. When connecting the TV to VCR, match the jack colors (Video = yellow, Audio Left = white, and Audio Right = red). If you connect an S-VIDEO output from VCR to the S-VIDEO input, the picture quality is improved; compared to connecting a regular VCR to the Video input. 2. Insert a video tape into the VCR and press PLAY on the VCR. (Refer to the VCR owners manual.) 3. Select the input source with using the TV/VIDEO button on the remote control. (If connected to A/V INPUT , select Video input source) Do not connect to both Video and S-Video at the same time. S-232C INPUT NTROL/SERVICE) VIDEO INPUT AUDIO INPUT DVD

/DTV INPUT L R VIDEO L AUDIO R COMPONENT 2 COMPONENT 1 MONITOR OUTPUT A/V INPUT1

(MONO) S V I D E O R E M O T E C O N T R O L DIGITAL AUDIO (OPTICAL) RGB INPUT AUDIO INPUT CABLE ANTENNA AC INPUT 1 2 ANT OUT ANT IN S-VIDEO OUT OUTPUT SWITCH 3 4 IN

(R) AUDIO (L) VIDEO VCR Rear Owners Manual 17 Installation External A/V Source Setup A/V Source Setup External How to connect Connect the audio and video cables from the external equip-

ment's output jacks to the TV input jacks, as shown in the figure. When connecting the TV to external equipment, match the jack colors (Video = yellow, Audio Left = white, and Audio Right = red). How to use 1. Select the input source with using the TV/VIDEO button on HDMI 2 DMI /DVI RS-232C INPUT

(CONTROL/SERVICE) OUTPUT COMPONENT2 INPUT DVI INPUT DIGITAL AUDIO (OPTICAL) RGB INPUT AUDIO INPUT DVD

/DTV INPUT VIDEO AUDIO VIDEO AUDIO L R L R COMPONENT INPUT 2 MONITOR OUTPUT S V I D E O R E M O T E C O N T R O L AC INPUT CABLE ANTENNA COMPONENT INPUT 1

(MONO) A/V INPUT the remote control. Note that this TV finds the connected input sources automatically for Video 1-2 and Component 1-

2. It is presumed that RGB, HDMI1/DVI and HDMI2 sources are connected. 2. Operate the corresponding external equipment. Refer to external equipment operating the tv guide on screen system. DVD Setup DVD Setup RS-232C INPUT

(CONTROL/SERVICE) Camcorder R AUDIO L VIDEO Video Game Set IEEE-1394 HDMI 2 HDMI1 /DVI Cable OUTPUT COMPONENT2 INPUT DVI INPUT or VIDEO AUDIO VIDEO AUDIO L R L R COMPONENT INPUT 2 MONITOR OUTPUT AC INPUT DIGITAL AUDIO (OPTICAL) RGB INPUT AUDIO INPUT DVD

/DTV INPUT COMPONENT INPUT 1

(MONO) A/V INPUT S-VIDEO REMOTE CONTROL CABLE ANTENNA DVD DIGITAL AUDIO OPTICAL

(R) AUDIO (L) B R S-VIDEO

(R) AUDIO (L) or How to connect 1. Connect the DVD video outputs (Y, PB, PR) to the COMPONENT (Y, PB, PR) INPUT jacks on the TV and connect the DVD audio outputs to the AUDIO INPUT jacks on the TV, as shown in the figure. 2. If your DVD only has an S-Video output jack, connect this to the S-VIDEO input on the TV and connect the DVD audio outputs to the AUDIO INPUT jacks on the TV, as shown in the figure. Note: If your DVD player does not have component video output, use S-Video. How to use 1. Turn on the DVD player, insert a DVD. 2. Use the TV/VIDEO button on the remote control to select Component 1 or Component 2. (If connected to S-VIDEO, select the Video or Front Video external input source.) 3. Refer to the DVD player's manual for operating instructions. Component Input ports To get better picture quality, connect a DVD player to the compo-

nent input ports as shown below. Component ports on the TV Video output ports on DVD player Y Y Y Y Y PB PR Pb B-Y Cb PB Pr R-Y Cr PR 18 Plasma TV Notes:

Digital Audio will not work for Component 1 input source. Digital Audio operation has priority if Digital Audio and AUDIO L/R are connected at the same time. Installation CableCARDTMTM Setup Setup CableCARD How to use Insert the CableCARDTMTM received from the cable service provider to the CableCARDTMTM slot of TV back panel. If the pairing information about this TV and the CableCARD is automati-

cally displayed on the screen, contact with the cable service provider by phone. Note :

CableCARDTMTM have the types of Motorola, Scientific Atlanta, SCM etc.. These 3 types of CableCARDTMTM can be used for this PLASMA TV. Cable IEEE-1394 HDMI 2 HDMI1 /DVI RS-232C INPUT

(CONTROL/SERVICE) OUTPUT COMPONENT2 INPUT DVI INPUT DIGITAL AUDIO (OPTICAL) RGB I Caution: When removing the CableCARDTMTM, do not fall it as this may cause impact to the CableCARDTMTM. HDSTB Setup HDSTB Setup

- This TV can receive Digital Over-the-air/Cable signals without an external digital set-top box. However, if you do receive Digital signals from a digital set-top box or other digital external device, refer to the figure as shown below.

- This TV supports HDCP (High-bandwidth Digital Contents Protection) protocol for Digital Contents (480p,720p,1080i). RS-232C INPUT

(CONTROL/SERVICE) IEEE-1394 HDMI 2 HDMI1 /DVI OUTPUT COMPONENT2 INPUT DVI INPUT DIGITAL AUDIO (OPTICAL) RGB INPUT AUDIO INPUT DVD

/DTV INPUT VIDEO AUDIO VIDEO AUDIO L R L R COMPONENT INPUT 2 MONITOR OUTPUT COMPONENT INPUT 1

(MONO) A/V INPUT S-VIDEO AC INPUT REMOTE CONTROL CABLE ANTENNA or or RGB-DTV OUTPUT

(R) AUDIO (L)

(R) AUDIO (L) DIGITAL AUDIO OPTICAL DVI-DTV OUTPUT HDMI-DTV OUTPUT DIGITAL AUDIO OPTICAL

(R) AUDIO (L) B R Digital Set-top Box How to connect Use the TVs COMPONENT (Y, PB, PR) INPUT, RGB, HDMI1/DVI or HDMI2 jack for video connections, depending on your set-top box connector. Then, make the corresponding audio connections. How to use 1. Turn on the digital set-top box. (Refer to the owners manual for the digital set-top box.) 2. Use TV/VIDEO on the remote control to select Component 1, Component 2, RGB-DTV, HDMI1/DVI or HDMI2 source. Signal 480i 480p 720p 1080i Component 1/2 RGB-DTV,HDMI1/DVI,HDMI2 Yes Yes Yes Yes No Yes Yes Yes Owners Manual 19 Installation PC Setup PC Setup

- This TV provides Plug and Play capability, meaning that the PC adjusts automatically to the TV's settings.

- The TV perceives 640x480, 60Hz as DTV 480p based on the PC graphic card, change the screen scanning rate for the graphic card accordingly.

<When the PC supports DVI>

How to connect 1. Connect the PC to HDMI1/DVI port of this TV with an HDMI-to-DVI cable(not supplied with this product). If you do not need to connect audio, HDMI2 port is also available for the DVI video connection. 2. If the PC(or the sound card of the PC) has a fiber optic digital audio output connector, connect the PC's audio output to DIGI-

TAL AUDIO(OPTICAL) port for DVI INPUT. 3. If the PC(or the sound card of the PC) has an analog audio output connector, connect the PC's audio output to AUDIO INPUT port located on the right side of RGB INPUT port. How To Use 1. To get the best picture quality, adjust the PC graphics card to 1024x768, 60Hz. 2. Select HDMI1/DVI input source in main input option of SETUP menu.(Refer to P.62) TV/VIDEO button is also available for this purpose. 3. Check the image on your TV. There may be noise associated with the resolution, vertical pattern, contrast or brightness in PC mode. If noise is present, change the PC output to another resolution, change the refresh rate to another rate or adjust the brightness and contrast on the VIDEO menu until the picture is clear. If the refresh rate of the PC graphic card can not be changed, change the PC graphic card or consult the manufacturer of the PC graphic card.

<When the PC supports RGB>

How to connect 1. Connect the PC to RGB INPUT port of this TV with a RGB cable. 2. If the PC(or the sound card of the PC) has an analog audio output connector, connect the PC's audio output to AUDIO INPUT port located on the right side of RGB INPUT port. How To Use 1. To get the best picture quality, adjust the PC graphics card to 1024x768, 60 Hz. 2. Select RGB-PC input source in main input option of SETUP menu.(Refer to P.57) Once you select RGB-PC in main input option of SETUP menu, TV/VIDEO button is also available for this purpose. 3. Check the image on your TV. There may be noise associated with the resolution, vertical pattern, contrast or brightness in PC mode. If noise is present, change the PC output to another resolution, change the refresh rate to another rate or adjust the brightness and contrast on the VIDEO menu until the picture is clear. If the refresh rate of the PC graphic card can not be changed, change the PC graphic card or consult the manufacturer of the PC graphic card. Monitor Display Specifications (RGB-PC ) Resolution Horizontal Frequency(KHz) Vertical Frequency(Hz) Resolution Horizontal Frequency(KHz) Vertical Frequency(Hz) 640x350 720x400 640x480 31.468 37.861 31.469 37.927 31.469 37.861 37.500 43.269 70.09 85.08 70.08 85.03 59.94 72.80 75.00 85.00 800x600 1024x768 35.156 37.879 48.077 46.875 53.674 48.363 56.476 60.023 56.25 60.31 72.18 75.00 85.06 60.00 70.06 75.02 20 Plasma TV Monitor Display Specifications (HDMI/DVI Mode) Resolution Horizontal Frequency(KHz) Vertical Frequency(Hz) Resolution Horizontal Frequency(KHz) Vertical Frequency(Hz) Installation 640x480 800x600 31.469 37.861 37.500 35.156 37.879 48.077 46.875 59.94 72.80 75.00 56.25 60.31 72.18 75.00 Monitor Out Setup Monitor Out Setup RGB INPUT AUDIO INPUT DVD

/DTV INPUT VIDEO AUDIO VIDEO AUDIO L R L R COMPONENT INPUT 2 MONITOR OUTPUT COMPONENT INPUT 1

(MONO) A/V INPUT S-VIDEO AC INPUT REMOTE CONTROL CABLE ANTENNA 1024x768 48.363 56.476 60.023 60.00 70.06 75.02 The TV has a special signal output capability which allows you to hook up a second TV or monitor. Connect the second TV or monitor to the TVs MONITOR OUTPUT. See the Operating Manual of the second TV or monitor for further details regarding that devices input settings. Note Component, RGB-PC/RGB-DTV, HDMI1/DVI and HDMI2 , DTV input sources cannot be used for Monitor out. S-VIDEO IN VIDEO

(L) AUDIO (R) Digital Audio Output Audio Output Digital Send the TVs audio to external audio equipment (stereo system) via the Digital Audio Output (Optical) port. How to connect 1. Connect one end of an optical cable to the TV Digital Audio

(Optical) Output port. 2. Connect the other end of the optical cable to the digital audio (opti-

cal) input on the audio equipment. 3. Set the TV Speaker option - Off in the AUDIO menu. Refer to page 64. See the external audio equipment instruction manual for operation. Caution: Do not look into the optical output port. Looking at the laser beam may damage your vision. RS-232C INPUT

(CONTROL/SERVICE) IEEE-1394 HDMI 2 HDMI1 /DVI Cable OUTPUT COMPONENT2 INPUT DVI INPUT DIGITAL AUDIO (OPTICAL) RGB INPUT AUDIO INPUT DVD

/DTV INPUT Owners Manual 21 Installation HDMI HDMI

- HDMITM, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC."

- This TV can receive the High-Definition Multimedia Interface(HDMI) or the Digital Visual Interface(DVI).

- This TV supports HDCP(High-bandwidth Digital Contents Protection) Protocol for 720x480p, 1280x720p, and 1920x1080i reso-

lution.

- When you connect this TV with a source device(DVD player, Set Top Box or PC) supporting Auto HDMI/DVI function, the output resolution of the source device will be automatically set to 1280x720p.

- If the source device does not support Auto HDMI1/DVI, you need to set the output resolution appropriately. To get the best picture quality, adjust the DVD Player or Set Top Box's output resolution to 1280x720p, and the PC graphics card's output resolution to 1024x768, 60Hz.

- If the source device has an HDMI output, no other audio connection is necessary because HDMI-to-HDMI connection includes both video and audio.

- If the source device has a DVI output and no HDMI output, a separated audio connection is necessary.

<When the source device (DVD player or Set Top Box) supports HDMI>

How To Connect 1. Connect the source device to HDMI1/DVI or HDMI2 port of this TV with an HDMI cable(not supplied with this product). 2. No separated audio connection is necessary. How To Use

- If the source device supports Auto HDMI function, the output resolution of the source device will be automatically set to 1280x720p.

- If the source device does not support Auto HDMI, you need to set the output resolution appropriately. To get the best picture quality, adjust the output resolution of the source device to 1280x720p.

- Select HDMI1/DVI or HDMI2 input source in main input option of SETUP menu.(Refer to P.59) VIDEO button is also available for this purpose.

<When the source device(DVD player or Set Top Box) supports DVI>

How To Connect 1. Connect the source device to HDMI1/DVI port of this TV with a HDMI-to-DVI cable(not supplied with this product). Do not use HDMI2 port for DVI connection if you want to connect audio. 2. A separated audio connection is necessary. 3. If the source device has a fiber optic digital audio output, connect the audio output to DIGITAL AUDIO(OPTICAL) port for DVI INPUT. 4. If the source device has an analog audio output connector, connect the PC's audio output to AUDIO INPUT port located on the right side of RGB INPUT port. How To Use

- If the source device supports Auto DVI function, the output resolution of the source device will be automatically set to 1280x720p.

- If the source device does not support Auto DVI, you need to set the output resolution appropriately. To get the best picture quality, adjust the output resolution of the source device to 1280x720p.

- Select HDMI1/DVI input source in main input option of SETUP menu.(Refer to P.59) VIDEO button is also available for this purpose. 22 Plasma TV Reference Reference Cable sample Installation HDMI Cable

(not supplied with the product) HDMI to DVI Cable

(not supplied with the product) Fiber Optic Digital Audio Cable

(not supplied with the product) Analog Audio Cable(RCA type)

(not supplied with the product) Analog Audio Cable(Stereo to RCA type)

(not supplied with the product) Owners Manual 23 Installation How to use 1. Connect the HDMI1/DVI Source Devices(DVD Player or Set Top Box or PC) and the TV SET. 2. Turn on the display by pressing the POWER button on the TV SET and HDMI1/DVI Source Devices remote control. 3. Select HDM1/DVI Input source in Main Input option of SETUP menu.(Refer to P.62) 4. Check the image on your TV SET. There may be noise associated with the resolution, vertical pattern, contrast or brightness in HDMI1/DVI Source Devices. If noise is present, change the HDMI1/DVI Source Devices to another resolution, change the refresh rate or adjust the brightness and contrast on the menu until the picture is clear. If the refresh rate of the PC graphics card can not changed, change the PC graphics card or consult the manufacturer of the PC graphics card. Notes:

- Depending on the graphics card, DOS mode may not work if you use a HDMI1 to DVI Cable.

- Avoid keeping a fixed image on the TV SET screen for a long period of time. The fixed image may become permanently imprint-

ed on the screen. Use the Orbiter screen saver when possible.

- When Source Devices connected HDMI/DVI Input, output PC Resolution(VGA, SVGA, XGA), Position, Size may not fit to Screen. As shown the lower picture, press the ADJUST button to adjust the screen Position of TV SET and contact an PC graphics card service center.

- When Source Devices connected HDMI1/DVI Input output TV SET Resolution(480p, 720p, 1080i), TV SET Display fit EIA/CEA-

861-B Specification to Screen. If not, refer to the Manual of HDMI1/DVI Source Devices or contact your service center.

- In case HDMI1/DVI Source Devices is not connected Cable or poor cable connection, "NO SIGNAL" OSD display in HDMI1/DVI Input. And In case of, Video Resolution not supported TV SET output in HDMI1/DVI Source Devices, "INVALID FORMAT" OSD display. Refer to the Manual of HDMI1/DVI Source Devices or contact your service center. POSITION G SIZE PHASE RESET Adjust Close F D E G In This Mode, the Supported TV SET Resolution Specification

- 1920 x 1080 I @ 59.94Hz / 60Hz, 16:9

- 1280 x 720 P @ 59.94Hz / 60Hz, 16:9(preferred format)

- 704 x 480 P @ 59.94Hz / 60Hz, 16:9

- 704 x 480 P @ 59.94Hz / 60Hz, 4:3 In This Mode, the Supported PC Resolution Specification

- 640 x 480 @ 60Hz

- 640 x 480 @ 72Hz

- 640 x 480 @ 75Hz

- 800 x 600 @ 56Hz

- 800 x 600 @ 60Hz

- 800 x 600 @ 72Hz

- 800 x 600 @ 75Hz

- 1024 x 768 @ 60Hz(preferred format)

- 1024 x 768 @ 70Hz

- 1024 x 768 @ 75Hz 24 Plasma TV Installation TV Guide On Screen Setup TV Guide On Screen Setup

- The TV Guide On Screen system uses Setup information to provide you with show listings and lineups in your areawhich are updated several times a day.

- Once you set up the TV according to manufacturers instructions, you are ready to set up the TV Guide On Screen system. Note:The TV Guide On Screen system interactive program guide provides listings for cable-ready, cable box, and digital cable services as well as over-the-air broadcast. It does not provide listings for satellite services. How to connect VCR and Cable Box 1.Antenna Service 1.Antenna Service RS-232C INPUT

(CONTROL/SERVICE) IEEE-1394 HDMI 2 HDMI /DVI Cable OUTPUT COMPONENT2 INPUT DVI INPUT DIGITAL AUDIO (OPTICAL) RGB INPUT AUDIO INPUT AC INPUT REMOTE CONTROL CABLE ANTENNA S-VIDEO ANT OUT ANT IN OUT OUTPUT SWITCH 3 4

(R) AUDIO (L) VIDEO IN S-VIDEO VCR Front VCR Rear 2. Cable Service without a Cable Box 2. Cable Service without a Cable Box RS-232C INPUT

(CONTROL/SERVICE) IEEE-1394 HDMI 2 HDMI /DVI Cable OUTPUT COMPONENT2 INPUT DVI INPUT DIGITAL AUDIO (OPTICAL) RGB INPUT AUDIO INPUT REMOTE CONTROL CABLE ANTENNA S-VIDEO AC INPUT ANT OUT ANT IN OUT OUTPUT SWITCH 3 4

(R) AUDIO (L) VIDEO IN S-VIDEO VCR Front VCR Rear Owners Manual 25 Installation 3.Cable Service without a Cable Box 3.Cable Service without a Cable Box VIDEO AUDIO VIDEO AUDIO L R L R COMPONENT INPUT 2 MONITOR OUTPUT Cable DVD

/DTV INPUT COMPONENT INPUT 1

(MONO) A/V INPUT 1 S-VIDEO AC INPUT REMOTE CONTROL CABLE ANTENNA or ANT OUT ANT IN OUT VCR Rear OUTPUT SWITCH 3 4

(R) AUDIO (L) VIDEO IN S-VIDEO VCR Front Cable Box Front 4. Antenna and Cable Service without a Cable Box RF Cable OUTPUT SWITCH 3 4

(R) AUDIO (L) VIDEO TV VCR Cable Box Rear IEEE-1394 HDMI 2 DVD

/DTV INPUT HDMI /DVI Cable VIDEO AUDIO VIDEO AUDIO L R L R COMPONENT INPUT 2 MONITOR OUTPUT COMPONENT INPUT 1

(MONO) A/V INPUT 1 S-VIDEO AC INPUT REMOTE CONTROL CABLE ANTENNA ANT OUT ANT IN OUT VCR Front S-VIDEO OUTPUT SWITCH 3 4

(R) AUDIO (L) VIDEO IN VCR Rear 5. 5. Antenna and Cable Service with a Cable Box Antenna and Cable Service with a Cable Box VIDEO AUDIO VIDEO AUDIO L R L R COMPONENT INPUT 2 MONITOR OUTPUT Cable DVD

/DTV INPUT COMPONENT INPUT 1

(MONO) A/V INPUT 1 S-VIDEO AC INPUT REMOTE CONTROL CABLE ANTENNA or ANT OUT ANT IN OUT VCR Front S-VIDEO OUTPUT SWITCH 3 4

(R) AUDIO (L) VIDEO IN VCR Rear Cable Box Front RF Cable 26 Plasma TV OUTPUT SWITCH 3 4

(R) AUDIO (L) VIDEO TV VCR Cable Box Rear Note:

The G-LINKTM cable is necessary for the TV Guide On Screen system to work with your Cable Box and VCR. See Page 23~24 for G-LINKTM connection instructions. Installation TV Guide On Screen Setup TV Guide On Screen Setup 1.Reminder Screen The TV Guide On Screen system's Reminder Screen appears:

-- after initial TV set up

-- if you power Off the TV and then power it back On To make a selection, use the D / E button to highlight to an option, and press ENTER.

"Set up TV Guide On Screen now," displays the Welcome Screen. Press ENTER to begin Setup.

"Remind me to set up later" returns you to watching TV.

"Don't remind me again" returns you to watching TV and stops the reminder screen from appearing upon power On. 2.Welcome Screen The TV Guide On Screen system's Welcome Screen appears:

-- by pressing the TV Guide key

-- when you power On your TV if you previously skipped "Set up TV Guide On Screen now" on the Reminder Screen. The Welcome Screen highlights features of the TV Guide On Screen system. Press ENTER to begin Setup. How to use 1. Screen 1: Country This screen asks you the location of your TV. Use the D / E button to highlight a country. Press ENTER to display Screen 2. Owners Manual 27 Installation 2. Screen 2: Enter Zip or Postal Code Option 1 If you selected USA in Screen 1, you see the ZIP Code screen. You input numbers by either pressing the number keys on the remote or using the D / E button to display a number, and then the F / G but-

ton to move to another field. Press ENTER to display Screen 3. Option 2 If you selected Canada in Screen 1, you see the Postal Code screen. You input characters by using the D / E button, and then the F / G button to move to another field. Press ENTER to display Screen 3. 3. Screen 3: Do you have Cable Service connected?

If you select Yes, you see Screen 4. If you select No, you see Screen 12. 4. Screen 4: Do you have a Cable Box?

If you select Yes, you see Screen 5. If you select No, you see Screen 12. 28 Plasma TV Installation 5. Screen 5: Which TV input is the cable box plugged into?

If you select Cable, you see Screen 6. If you make any other choice, you see Screen 7 . 6. Screen 6: Cable Box Tuning Channel Select the channel used for the cable box. Press ENTER to display Screen 7. 7. Screen 7: Cable Box Configuration Diagram The diagram shows the correct way to install the G-LINK Cable from the back of the device to the cable box. Make sure the G-LINKTM Cable is properly installed. Press ENTER to display Screen 8. Owners Manual 29 Installation 8. Screen 8: Cable Box Brand Name Use the D / E button to select a cable box brand. Press ENTER to display Screen 9. 9. Screen 9: Cable Box Preparation Follow the on-screen instructions, and press ENTER to display Screen 10. 10. Screen 10: Cable Box Code Testing When testing is done, Screen 11 displays automatically. 11. Screen 11: Cable Box Tuned to Channel 9?

If you select Yes, you see Screen 12. If you select No, a different code is tested in Screen 10. Note:

Many Cable Boxes require testing more than one code. If you select Test this code again, the same code is tested again in Screen 10. 30 Plasma TV 12. Screen 12: Do you have an antenna connected?

If you select Yes, you see Screen 13. Note:

If you selected No in Screen 3 then you must select Yes in this screen to receive a channel lineup and listings. If you select No, you see Screen 13. 13. Screen 13: Are your basic settings correct?

If you select Yes, you see Screen 14. If you select No, you see Screen 1. 14. Screen 14: Congratulations Press ENTER to display Screen 15. Installation Owners Manual 31 Installation 15. Screen 15: Helpful Information This screen tells you valuable information on using your Guide. Press ENTER to watch TV. Notes:

The TV Guide On Screen system receives program listings data through your cable or over-the-air video signal. In order to receive regular program listings, please remember to do the following:

1. Turn OFF your TV when it is not in use. (Do not unplug the power cord.) 2. If you have a Cable box connected, leave it ON. 3. If you have more than one Cable system in your area, you may be prompted to select which Cable systems program data to download. If so prompted, please follow the on-screen instructions. 32 Plasma TV Operation Operation Operation TTurning the TV On urning the TV On 1. First, connect power cord correctly. At this moment, the TV switches to standby mode. In standby mode to turn TV on, press the power, TV/VIDEO, CH (D / E) button on the TV or press the POWER, TV/VIDEO, TV INPUT, CH (+, -), Number (0 ~ 9) button on the TV . 2. Select the viewing source by using TV/VIDEO, TV INPUT button on the remote control. This TV is programmed to remember which mode it was last set to, even if you turn the TV off. 3. When finished using the TV, press the POWER button on the remote control. The TV reverts to standby mode. Notes:

If you intend to be away on vacation, disconnect the power plug from the wall power outlet. After turning on the TV, it takes time to be initialized for the TV Guide On Screen System. When the TV is turned on, blinks orange in standby mode, blinks green. And after orange stop the blinking, directly turn on the TV. But in case of green, screen is displayed at 3~4 minutes later. If power isnt turn on in red, contact your service center. Owners Manual 33 Operation HOME Menu HOME Menu

- The menus can be shown on the screen in the selected language. First select your language. Recorded TV Photo List Music List TV Guide TV Menu IEEE 1394 Schedule 34 Plasma TV TV Setup TV Setup Operation On-screen Menus Language Selection On-screen Menus Language Selection

- The menus can be shown on the screen in the selected language. First select your language. 1. Press the MENU button and then use D / E button to select the OPTION menu. 2. Press the G button and then use D / E button to select Language. 3. Press the G button and then use D / E button to select your desired language. From this point on, the on-screen menus will be shown in the selected language. 4. Press EXIT button to return to TV viewing or press MENU button to return to the previous menu. SETUP Advanced Aspect Ratio VIDEO Caption AUDIO TIME OPTION LOCK CABLE Caption / Text Caption Option Language ISM Method Front Display Auto Demo MENU Previous G English Espaol Franais Owners Manual 35 Operation Setup Menu Options Setup Menu Options EZ Scan (Channel Search) EZ Scan (Channel Search)

- Automatically finds all channels available through antenna or cable inputs, and stores them in memory on the channel list.

- Run EZ Scan again after any Antenna/Cable connection changes. 1. Press the MENU button and then use D / E button to select the SETUP menu. 2. Press the G button and then use D / E button to select EZ Scan. 3. Press the ENTER button to begin the channel search. Allow EZ Scan to complete the channel search cycle for ANTENNA, and CABLE. Manual Scan Manual Scan 1. Press the MENU button and then use D / E button to select the SETUP menu. 2. Press the G button and then use D / E button to select Manual Scan. 3. Press the G button and then use D / E button to select TV, DTV, CATV, and CADTV. 4. Press the G button and then use D / E button to select channel number you want to add or delete. 5. Press the ENTER button to add or delete for the channel number. 6. Press EXIT button to return to TV viewing or press MENU button to return to the previous menu. SETUP EZ Scan VIDEO Manual Scan Channel Edit DTV Signal AUDIO Channel Label TIME OPTION LOCK CABLE Main Input Sub Input Input Edit Set ID MENU Previous G Select channel type and channel number. TV 20 Notes:

This channel number is a physical channel number, which is different from normal channel number showed in Channel Edit. When a cable box connects to the physical channel 2,3 or 4 in TV Guide Setup, cable channels(CATV or CADTV) will not be scanned by EZ Scan or Manual Scan. When inserting the CableCARDTM, CATV, CADTV is not working in EZ Scan. TV: analog antenna(over-the-air) TV signal DTV: digital antenna(over-the-air) TV signal CATV: analog cable TV signal CADTV: digital cable TV signal 36 Plasma TV Operation Channel Edit Channel Edit

- Create two different types of channel lists in memory: Custom list and Favorite channel list from the default channel list created from the EZ Scan channel search.

- A custom list can be created by toggling each channel on or off with ENTER button. The. The channels in the Custom List are displayed in black color, and the channels deleted from the Custom List are displayed in gray color. Once a channel is highlighted you can add or delete the channel by referring to the small window at the top-left corner of the screen.You can create your own Favorite List. Use the FAV button on the remote control when a channel is highlighted and then you can add or delete the channel to/from the Favorite List. SETUP EZ Scan VIDEO Manual Scan Channel Edit DTV Signal AUDIO Channel Label TIME OPTION LOCK CABLE Main Input Sub Input Input Edit Set ID MENU Previous G Selection ( G or ) leads you to the channel edit screen. 1. Press the MENU button and then use D / E button to select the SETUP menu. 2. Press the G button and then use D / E button to select Channel Edit. 3. Press the G button. You will now see a screen filled with channel numbers and a preview picture. 4. Use D / E / F / G button to select a channel and then use the ENTER button to add or delete it. Press FAV button to add the channel to the Favorite List. 5. Press EXIT button to return to TV viewing or press MENU button to return to the previous menu. Note:

When Cable Box connect to RF2,3,4 in TV Guide Setup, CATV, CADTV is not working in EZ Scan. DTV Signal Strength DTV Signal Strength

- Shows how strong your DTV signal is and whether you need to adjust your antenna or digital cable input. The higher the signal strength, the less likely you are to experience picture degradation.

- DTV Signals: Only when the input signal is DTV or CADTV, this function is available. 1. Press the MENU button and then use D / E button to select the SETUP menu. 2. Press the G button and then use D / E button to select DTV Signal. 3. View the on-screen signal strength monitor to see the quality of the signal being received. 5. Press EXIT button to return to TV viewing or press MENU button to return to the previous menu. Owners Manual 37 Operation Setup Menu Options Setup Menu Options Channel Label Setup Channel Label Setup

- Choose preset labels for your channels.

If a channel label is provided on the signal from the broadcasting station, the TV displays a short name for a channel -

even if you didn't preset a label for the channel. SETUP EZ Scan VIDEO AUDIO TIME OPTION LOCK CABLE Manual Scan Channel Edit DTV Signal Channel Label G Main Input Sub Input Input Edit Set ID MENU Previous Selection ( G or ) leads you to the channel logo screen. 1. Press the MENU button and then use D / E button to select the SETUP menu. 2. Press the G button and then use D / E button to select Channel Label. 3. Press the G button. You will now see a screen filled with Labels and a preview screen. 4. Use the CH +/- button to select a channel to Label. 5. Use D / E / F / G button to select the appropriate label for the channel, then press ENTER button to set the Label to the selected channel. If you press ENTER button, you will see the channel banner.

Main Picture Source Selection Main Picture Source Selection

- Changes the picture source so you can watch your off-air TV, cable TV, VCR, DVD, or any other devices that are connected to your TV. 1. Press the MENU button and then use D / E button to select the SETUP menu. 2. Press the G button and then use D / E button to select Main Input. 3. Press the G button and then use D / E button to select the source: Antenna, Cable, Video, Front Video, Component1, Component2, RGB-DTV (or RGB-PC), HDMI1/DVI, HDMI2. 4. Press EXIT button to return to TV viewing or press MENU button to return to the previous menu. Input Edit Input Edit 1. Press the MENU button and then use D / E button to select the SETUP menu. 2. Press the G button and then use D / E button to select Input Edit. 3. Press the G button and then use D / E button to select the source: Video, Front Video, Component1, Component2, RGB, HDMI1/DVI. 4. Press EXIT button to return to TV viewing or press MENU button to return to the previous menu. 38 Plasma TV SETUP VIDEO EZ Scan Manual Scan Channel Edit DTV Signal AUDIO Channel Label TIME OPTION LOCK CABLE G Main Input Sub Input Input Edit Set ID MENU Previous Antenna Cable Video1 Video2 Component1 Component2 RGB-DTV HDMI1/DVI HDMI2(VCR) SETUP EZ Scan VIDEO Manual Scan Channel Edit DTV Signal AUDIO Channel Label TIME OPTION LOCK CABLE Main Input Sub Input Input Edit Set ID MENU Previous Video1 Cable Box Video2 VCR Component1 DVD Component2 Set Top Box G RGB PC HDMI1/DVI Game HDMI2 STB VVideo Menu Options ideo Menu Options EZ Picture EZ Picture

- EZ Picture adjusts the TV for the best picture appearance. Select the preset value in the EZ Picture menu based on the program category. Operation

- When adjusting Video menu options (contrast, brightness, color, sharpness, tint, and color temperature) manually, EZ Picture automatically changes to Custom.

- Daylight, Normal, Night Time, Movie, Video Game, and Sports settings are preset for optimum picture quality at the factory and are not adjustable. 1. Press the EZ PIC button repeatedly to select the picture appearance setup option as shown below:

Custom (your own settings), Daylight, Normal, Night Time, Movie, Video Game, and Sports. You can also use the VIDEO menu to adjust EZ Picture. 2. Press the EXIT button to save and return to TV viewing. Manual Picture Control (Custom option) option) Manual Picture Control (

- Adjust the picture appearance to suit your preference and viewing situations. 1. Press the MENU button and then use D / E button to select the VIDEO menu. 2. Press the G button and then use D / E button to select the desired picture option

(Contrast, Brightness, Color, Sharpness, or Tint ). 3. Press the G button and then use F / G button to make appropriate adjustments. 4. Press EXIT button to return to TV viewing or press MENU button to return to the previous menu. Color TTemperature Control emperature Control Color

- Choose one of three automatic color adjustments. Set to warm to enhance hotter colors such as red, or set to cool to see less intense colors with more blue. 1. Press the MENU button and then use D / E button to select the VIDEO menu. 2. Press the G button and then use D / E button to select Color Temperature . 3. Press the G button and then use D / E button to select either Cool, Medium or Warm. 4. Press EXIT button to return to TV viewing or press MENU button to return to the previous menu. VVideo Reset ideo Reset

- Use to quickly reset all the Video menu options to their original factory preset values. 1. Press the MENU button and then use D / E button to select the VIDEO menu. 2. Press the G button and then use D / E button to select Video Reset . 3. Press the G button to reset the Video menu options to original values. 39 Plasma TV SETUP VIDEO EZ Picture Contrast Brightness Color AUDIO Sharpness 85 50 50 50 G TIME OPTION LOCK CABLE 0 R G Tint Color Temperature Video Reset MENU Previous SETUP VIDEO EZ Picture Contrast Brightness Color AUDIO Sharpness TIME Tint Color Temperature G Cool OPTION Video Reset Medium Warm LOCK CABLE MENU Previous SETUP VIDEO EZ Picture Contrast Brightness Color AUDIO Sharpness TIME OPTION LOCK CABLE Tint Color Temperature Video Reset G Selection ( G or ) presets the video configuration. MENU Previous Owners Manual 39 Operation Audio Menu Options Audio Menu Options Audio Language Audio Language

- Other languages may be available if a digital signal is provided by the broad-

casting station. 1. Press the MENU button and then use D / E button to select the AUDIO menu. 2. Press the G button and then use D / E button to select Audio Language. 3. Press the G button and then use D / E button to select: English, Spanish, or French. 4. Press EXIT button to return to TV viewing or press MENU button to return to the previous menu. English Spanish French SETUP Audio Language G VIDEO AUDIO TIME OPTION LOCK CABLE EZ SoundRite EZ Sound Balance Treble Bass Front Surround TV Speaker BBE MENU Previous EZ SoundRite EZ SoundRite

- Scans for changes in sound level during commercials, then adjusts the sound to match the specified audio level. SoundRite makes sure that the volume level remains consistent whether you are watching a commercial or a regular TV program. 1. Press the MENU button and then use D / E button to select the AUDIO menu. 2. Press the G button and then use D / E button to select EZ SoundRite. 3. Press the G button and then use D / E button to select On or Off. 4. Press EXIT button to return to TV viewing or press MENU button to return to the previous menu. Off On SETUP Audio Language EZ SoundRite G VIDEO AUDIO TIME OPTION LOCK CABLE EZ Sound Balance Treble Bass Front Surround TV Speaker BBE MENU Previous EZ Sound EZ Sound

- EZ Sound lets you enjoy the best sound without any special adjustment because the TV sets the appropriate sound options based on the program content.

- When adjusting sound options (treble, bass, and front surround) manually, EZ Sound automatically switches Custom.

- Normal, Stadium, News, Music, and Theater are preset for good sound quality at the factory and are not adjustable. 1. Press the EZ SOUND button repeatedly to select the appropriate sound setup as shown below:

Custom (your own settings), Normal, Stadium, News, Music, and Theater. You can also adjust EZ Sound in the AUDIO menu. 2. Press EXIT button to save and return to TV viewing. 40 Plasma TV