submitted | available | document details (if available) | source link |
---|---|---|---|
December 06 2008 | Zenith.book Kenny.Hu Acrobat Distiller 6.0 (Windows) |
various | User Manual 1 | Users Manual | 5.69 MiB | December 06 2008 |
Zenith.book Page 1 Wednesday, April 2, 2008 11:46 AM Installation and Operating Guide Model Numbers | Z32LC6D, Z37LC6D | LCD TV ENERGY STAR is a set of power-saving guidelines issued by the U.S. Environmental Protection Agency (EPA). As an ENERGY STAR Partner LGE U. S. A.,Inc. has determined that this product meets the ENERGY STAR guidelines for energy efficiency. Copyright 2008, LG Electronics USA, Inc. Zenith.book Page 2 Wednesday, April 2, 2008 11:46 AM Zenith.book Page 1 Wednesday, April 2, 2008 11:46 AM WARNING / CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER TO QUALIFIED SERVICE PERSONNEL. lightning The flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated dangerous voltage within the products enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING/CAUTION TO REDUCE THE RISK OF FIRE AND ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. WARNING / CAUTION WARNING / CAUTION To prevent fire or shock hazards, do not expose this product to rain or moisture. FCC NOTICE in a residential Class B digital device This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to reasonable protection against harmful provide interference installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help. Any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. NOTE TO CABLE/TV INSTALLER CAUTION This reminder is provided to call the CATV system installers attention to Article 820-40 of the National Electric Code (U.S.A.). The code provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of the cable entry as practical. Do not attempt to modify this product in any way without written authorization from LG Electronics. Unauthorized modification could void the users authority to operate this product. 1 Zenith.book Page 2 Wednesday, April 2, 2008 11:46 AM SAFETY INSTRUCTIONS IMPORTANT SAFETY INSTRUCTIONS Important safety instructions shall be provided with each apparatus. This information shall be given in a separate booklet or sheet, or be located before any operating instructions in an instruction for installation for use and supplied with the apparatus. This information shall be given in a language acceptable to the country where the apparatus is intended to be used. The important safety instructions shall be entitled Important Safety Instructions. The following safety instructions shall be included where applicable, and, when used, shall be verbatim as follows. Additional safety information may be included by adding statements after the end of the following safety instruction list. At the manufacturers option, a picture or drawing that illustrates the intent of a specific safety instruction may replaced immediately adjacent to that safety instruction:
Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong, The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. Only use attachments/accessories specified by the manufacturer. Unplug this apparatus when unused for long periods of time. Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. Do not use this apparatus near water. Clean only with dry cloth. Do not block any ventilation openings. Install in accordance manufacturers instructions. with the Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. When mounting a TV on the wall, make sure not to install TV by hanging power and signal cables on the back of the TV. 2 Zenith.book Page 3 Wednesday, April 2, 2008 11:46 AM Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. Protect the power cord from physical or mechanical abuse, such as being twisted, kinked, pinched, closed in a door, or walked upon. Pay particular attention to plugs, wall outlets, and the point where the cord exits the appliance. Never touch this apparatus or antenna during a thunder or lighting storm. Do not allow an impact shock or any objects to fall into the product, and do not drop onto the screen with something. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has exposed to rain or moisture, does not operate normally, or has been dropped. CAUTION concerning the Power Cord :
Most appliances recommend they be placed upon a dedicated circuit; that is, a single outlet circuit which powers only that appliance and has no additional outlets or branch circuits. Check the specification page of this owner's manual to be certain. Do not overload wall outlets. Overloaded wall loose or damaged wall outlets, outlets, frayed power cords, or extension cords, damaged or cracked wire insulation are dangerous. Any of these conditions could result in electric shock or fire. Periodically examine the cord of your appliance, and if its appearance indicates damage or deterioration, unplug it, discontinue use of the appliance, and have the cord replaced with an exact replacement part by an authorized servicer. Outdoor use marking :
WARNING - To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture. Wet Location Marking : Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be placed on or over apparatus. GROUNDING Ensure that you connect the earth ground wire to prevent possible electric shock. If grounding methods are not possible, have a qualified electrician install a separate circuit breaker. Do not try to ground the unit by connecting it to telephone wires, lightening rods, or gas pipes. Power Supply Short-circuit Breaker DISCONNECTING DEVICE FROM MAINS Mains plug is the disconnecting device. The plug must remain readily operable. 3 PICTURE CONTROL PICTURE SIZE (ASPECT RATIO) CONTROL ......40 PRESET PICTURE SETTINGS ...................................41
- Picture Mode - Preset ........................................41
- Color Tone - Preset ............................................42 MANUAL PICTURE ADJUSTMENT .........................43
- Picture Mode - User Mode ...............................43
- Color Tone - User Mode ...................................44 DB - PICTURE IMPROVEMENT TECHNOLOGY 45 ADVANCED - CINEMA 3:2 PULL DOWN MODE ............................................................................46 ADVANCED - BLACK (DARKNESS) LEVEL ..........47 PICTURE RESET ..........................................................48 SOUND & LANGUAGE CONTROL AUTO VOLUME LEVELER (AUTO VOLUME) ......49 PRESET SOUND SETTINGS (SOUND MODE) ...50 SOUND SETTING ADJUSTMENT - USER MODE ............................................................................51 BALANCE ......................................................................52 TV SPEAKERS ON/OFF SETUP ...............................53 STEREO/SAP BROADCASTS SETUP .....................54 AUDIO LANGUAGE ....................................................55 ON-SCREEN MENUS LANGUAGE SELECTION ..56 CAPTION MODE ........................................................57
- Analog Broadcasting System Captions ..........58
- Digital Broadcasting System Captions ..........59
- Caption Option ....................................................60 Zenith.book Page 4 Wednesday, April 2, 2008 11:46 AM CONTENTS WARNING / CAUTION .................................1 SAFETY INSTRUCTIONS .............................2 FEATURE OF THIS TV ....................................6 PREPARATION ACCESSORIES ................................................................7 FRONT PANEL INFORMATION .................................8 BACK PANEL INFORMATION ....................................9 STAND INSTALLATION ............................................ 10 VESA WALL MOUNTING ..........................................11 DESKTOP PEDESTAL INSTALLATION ..................11 CABLE MANAGEMENT ............................................. 12 ATTACHING THE TV TO A DESK ......................... 13 SECURING THE TV TO THE WALL TO PREVENT FALLING ........................................................................14 ANTENNA OR CABLE CONNECTION .................15 EXTERNAL EQUIPMENT SETUP HD RECEIVER SETUP ................................................ 16 DVD SETUP .................................................................19 VCR SETUP ..................................................................21 OTHER A/V SOURCE SETUP .................................23 PC SETUP ..................................................................... 24 AUDIO OUT CONNECTION .................................. 29 WATCHING TV / CHANNEL CONTROL REMOTE CONTROL FUNCTIONS ........................ 30 TURNING ON TV ....................................................... 32 CHANNEL SELECTION ............................................. 32 VOLUME ADJUSTMENT ........................................... 32 ON-SCREEN MENUS SELECTION ......................... 33 CHANNEL SETUP ....................................................... 34
- Auto Scan (Auto Tuning) .................................. 34
- Add/Delete Channel (Manual Tuning) .......... 35
- Channel Editing ...................................................36 INPUT LIST ..................................................................37 INPUT LABEL ............................................................... 38 KEY LOCK .................................................................... 39 4 Zenith.book Page 5 Wednesday, April 2, 2008 11:46 AM TIME SETTING CLOCK SETTING ....................................................... 61
- Auto Clock Setup ................................................ 61
- Manual Clock Setup ........................................... 62 AUTO ON/OFF TIMER SETTING .......................... 63 SLEEP TIME SETTING ............................................... 64 AUTO SHUT-OFF SETTING ................................... 65 PARENTAL CONTROL / RATINGS SET PASSWORD & LOCK SYSTEM ...................... 66 CHANNEL BLOCKING .............................................. 68 EXTERNAL INPUT BLOCKING ............................... 68 MOVIE & TV RATING ............................................... 69 DOWNLOADABLE RATING ..................................... 71 APPENDIX TROUBLESHOOTING .............................................. 72 MAINTENANCE .......................................................... 74 PRODUCT SPECIFICATIONS ................................. 75 PROGRAMMING THE REMOTE CONTROL ....... 76 IR CODES ..................................................................... 79 EXTERNAL CONTROL THROUGH RS-232C .... 81 OPEN SOURCE LICENSE ......................................... 88 5 Zenith.book Page 6 Wednesday, April 2, 2008 11:46 AM FEATURE OF THIS TV High-definition television. High-resolution digital television broadcast and playback system composed of roughly a million or more pixels, 16:9 aspect-ratio screens, and AC3 digital audio. A subset of digital television, HDTV formats include 1080i and 720p resolutions. HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing."
Manufactured under license from Dolby Laboratories. Dolby and the double-D symbol are trademarks of Dolby Laboratories. is a trademark of SRS Labs, Inc. TruSurround XT technology is incorporated under license from SRS Labs, Inc. FOR LCD TV
If the TV feels cold to the touch, there may be a small flicker when it is turned on. This is normal, there is nothing wrong with TV.
Some minute dot defects may be visible on the screen, appearing as tiny red, green, or blue spots. However, they have no adverse effect on the monitor's performance.
Avoid touching the LCD screen or holding your finger(s) against it for long periods of time. Doing so may produce some temporary distortion effects on the screen. On Disposal The fluorescent lamp used in this product contains a small amount of mercury. Do not dispose of this product with general household waste. Disposal of this product must be carried out in accordance to the regulations of your local authority. 6 Zenith.book Page 7 Wednesday, April 2, 2008 11:46 AM PREPARATION ACCESSORIES Ensure that the following accessories are included with your TV. If an accessory is missing, please contact the dealer where you purchased the TV. The accessories included may differ from the images below. Owners Manual CD Manual Remote Control, Batteries Power Cord Cable Management Clip 4-Bolts for stand assembly
(Refer to p.10) Screw for stand fixing
(Refer to p.13)
* Wipe spots on the exterior only with the polishing cloth.
* Do not wipe roughly when removing stain. Please be cautions of that excessive pressure may cause scratch or discoloration. Polishing Cloth Option Extras When using the VGA (D-sub 15 pin cable) PC connection, the user must use shielded signal interface cables with ferrite cores to maintain standards compliance. D-sub 15 pin Cable P R E P A R A T O N I 7 Zenith.book Page 8 Wednesday, April 2, 2008 11:46 AM PREPARATION FRONT PANEL INFORMATION
Here shown may be somewhat different from your TV.
NOTE: If your product has a protection tape attached, remove the tape. And then wipe the product with a cloth (If a polishing cloth is included with your product, use it). CHANNEL (, )Buttons VOLUME (, )Buttons ENTER Button MENU Button INPUT Button POWER Button Power/Standby Indicator Illuminates red in standby mode. Illuminates green when the set is switched on. Remote Control Sensor P R E P A R A T O N I 8 Zenith.book Page 9 Wednesday, April 2, 2008 11:46 AM BACK PANEL INFORMATION
Here shown may be somewhat different from your TV. P R E P A R A T O N I 9 HDMI/DVI IN, HDMI IN Digital Connection. Supports HD video and Digital audio. Doesnt support 480i. Accepts DVI video using an adapter or HDMI to DVI cable (not included) COMPONENT IN Analog Connection. Supports HD. Uses a red, green, and blue cable for video &
red and white for audio. RGB (PC) Analog PC Connection. Uses a D-sub 15 pin cable (VGA cable). AUDIO (RGB/DVI) 1/8 headphone jack for analog PC audio input. SERVICE ONLY Used for software updates. REMOTE CONTROL PORT For a wired remote control. ANTENNA/CABLE IN Connect over-the air signals to this jack. Connect cable signals to this jack. DIGITAL AUDIO OUT Digital audio output for use with amps and home theater systems. Includes an optical and/or coaxial connection. Note: In standby mode, these ports do not work. RS-232C IN (CONTROL & SERVICE) PORT Used by third party devices. AUDIO OUT Analog audio output for use with amps and home theater systems. AV (Audio/Video) IN Analog composite connection. Supports standard definition video only (480i). S -VIDEO Better quality than standard composition. Supports standard definition video only (480i). Power Cord Socket For operation with AC power. Caution: Never attempt to operate the TV on DC power. Zenith.book Page 10 Wednesday, April 2, 2008 11:46 AM PREPARATION STAND INSTALLATION
Here shown may be somewhat different from your TV. Carefully place the product screen side down on a cushioned surface that will protect product and screen from damage. Assemble the product stand with the product as shown. Securely install the 4 bolts provided. P R E P A R A T O N I 10 Zenith.book Page 11 Wednesday, April 2, 2008 11:46 AM VESA WALL MOUNTING This TV accepts VESA FDMI compliant mounts via the four screw holes on the back of the TV. These mounts are sold by third parties and not available from LG. Refer to the instructions included with the mount for more info. Z32LC6D: 200 mm Z37LC6D: 600 mm Z32LC6D: 100 mm Z37LC6D: 400 mm NOTE
!
Screw length needed depends on the wall mount used. For further information, refer to the instructions included with the mount. DESKTOP PEDESTAL INSTALLATION For proper ventilation, allow a clearance of 4 inches on all four sides from the wall. 4 inches 4 inches 4 inches 4 inches CAUTION
Ensure adequate ventilation by following the clearance recommendations. P R E P A R A T O N I 11 Zenith.book Page 12 Wednesday, April 2, 2008 11:46 AM PREPARATION CABLE MANAGEMENT
Here shown may be somewhat different from your TV. Connect the cables as necessary. To connect an additional equipment, see the EXTERNAL EQUIPMENT SETUP section. Install the CABLE MANAGEMENT CLIP as shown. CABLE MANAGEMENT CLIP NOTE
!
Do not hold the CABLE MANAGEMENT CLIP when moving the product.
- If the product is dropped, you may be injured or the product may be broken. How to remove the CABLE MANAGEMENT CLIP
Hold the CABLE MANAGEMENT CLIP with both hands and pull it backward. P R E P A R A T O N I 12 Zenith.book Page 13 Wednesday, April 2, 2008 11:46 AM ATTACHING THE TV TO A DESK The TV must be attached to a desk so it cannot be pulled in a forward/backward direction, potentially causing injury or damaging the product. Use only an attached screw. 1-Screw
(provided as parts of the product) Stand Desk WARNING
To prevent TV from falling over, the TV should be securely attached to the floor/wall per installation instructions. Tipping, shaking, or rocking the machine may cause injury. P R E P A R A T O N I 13 Zenith.book Page 14 Wednesday, April 2, 2008 11:46 AM PREPARATION SECURING THE TV TO THE WALL TO PREVENT FALLING
You should purchase necessary components to prevent TV from falling off of the stand.
Image shown may differ from your TV. We recommend that you set up the TV close to a wall so it cannot fall over if pushed backwards. Additionally, we recommend that the TV be attached to a wall so it cannot be pulled in a forward direction, potentially causing injury or damaging the product. Caution: Please make sure that children dont climb on or hang from the TV.
Insert the eye-bolts (or TV brackets and bolts) to tighten the product to the wall as shown in the picture.
* If your product has the bolts in the eye-bolts position before inserting the eye-bolts, loosen the bolts. Secure the wall brackets with the bolts (not provided as parts of the product, must purchase separately) to the wall. Match the height of the bracket that is mounted on the wall to the holes in the product. Ensure the eye-bolts or brackets are tightened securely.
Use a sturdy rope (not provided as parts of the product, must purchase separately) to tie the product. It is safer to tie the rope so it becomes horizontal between the wall and the product. P R E P A R A T O N I 14 Zenith.book Page 15 Wednesday, April 2, 2008 11:46 AM ANTENNA OR CABLE CONNECTION
To prevent damage do not connect to the power outlet until all connections are made between the devices. 1. Antenna (Analog or Digital) Wall Antenna Socket or Outdoor Antenna without a Cable Box Connections. For optimum picture quality, adjust antenna direction if needed. Wall Antenna Socket Outdoor Antenna
(VHF, UHF) 2. Cable Cable TV Wall Jack Multi-family Dwellings/Apartments
(Connect to wall antenna socket) RF Coaxial Wire (75 ohm) Single-family Dwellings/Houses
(Connect to wall jack for outdoor antenna) Copper Wire Be careful not to bend the copper wire when connecting the antenna. RF Coaxial Wire (75 ohm) Antenna UHF VHF Signal Amplifier
To improve the picture quality in a poor signal area, please purchase a signal amplifier and install properly.
If the antenna needs to be split for two TVs, install a 2-Way Signal Splitter.
If the antenna is not installed properly, contact your dealer for assistance. P R E P A R A T O N I 15 Zenith.book Page 16 Wednesday, April 2, 2008 11:46 AM EXTERNAL EQUIPMENT SETUP
To prevent the equipment damage, never plug in any power cords until you have finished connecting all equipment.
This part of EXTERNAL EQUIPMENT SETUP mainly use picture for LCD TV model. HD RECEIVER SETUP This TV can receive Digital Over-the-air/Cable signals without an external digital set-top box. However, if you do receive digital signals from a digital set-top box or other digital external device, refer to the figure as shown below. E X T E R N A L E Q U P M E N T S E T U P I Component Connection 1. How to connect Connect the video outputs (Y, PB, PR) of the digital set top box to the COMPONENT IN VIDEO 1 jacks on the set. Match the jack colors (Y = green, PB = blue, and PR = red). Connect the audio output of the digital set-top box to the COMPONENT IN AUDIO 1 jacks on the TV. 2. How to use
Turn on the digital set-top box.
(Refer to the owners manual for the digital set-top box operation)
Select the Component 1 input source on the TV using the INPUT button on the remote control.
If connected to COMPONENT IN2 input, select the Component 2 input source on the TV. Supported Resolutions Y, CB/PB, CR/PR Signal 480i 480p 720p 1080i 1080p 16 Component 1/2 HDMI1/2 Resolution Horizontal Frequency (KHz) Vertical Frequency (Hz) Yes Yes Yes Yes Yes No Yes Yes Yes Yes 720x480i 720x480p 1280x720p 1920x1080i 1920x1080p 15.73 15.73 31.47 31.50 44.96 45.00 33.72 33.75 26.97 27.00 33.71 33.75 67.432 67.50 59.94 60.00 59.94 60.00 59.94 60.00 59.94 60.00 23.976 24.00 29.97 30.00 59.94 60.00 Zenith.book Page 17 Wednesday, April 2, 2008 11:46 AM HDMI Connection 1. How to connect Connect the digital set-top box to HDMI/DVI IN 1 or HDMI IN 2 jack on the TV. No separated audio connection is necessary. HDMI supports both audio and video. 2. How to use
Turn on the digital set-top box.
(Refer to the owners manual for the digital set-top box.)
Select the HDMI1 or HDMI2 input source on the TV using the INPUT button on the remote control. E X T E R N A L E Q U P M E N T S E T U P I HDMI-DTV OUTPUT HDMI1/DVI-DTV, HDMI2-DTV mode Resolution 720x480p 1280x720p 1920x1080i 1920x1080p Horizontal Frequency (KHz) Vertical Frequency (Hz) 31.47 31.50 44.96 45.00 33.72 33.75 26.97 27.00 33.71 33.75 67.432 67.50 59.94 60.00 59.94 60.00 59.94 60.00 23.976 24.00 29.97 30.00 59.939 60.00 17 Zenith.book Page 18 Wednesday, April 2, 2008 11:46 AM EXTERNAL EQUIPMENT SETUP DVI to HDMI Connection E X T E R N A L E Q U P M E N T S E T U P I 1. How to connect DVI-DTV OUTPUT Connect the DVI output of the digital set-top box to the HDMI/DVI IN 1 jack on the TV. Connect the audio output of the digital set-top box to the AUDIO (RGB/DVI) jack on the TV. 2. How to use
Turn on the digital set-top box. (Refer to the owners manual for the digital set-top box.)
Select the HDMI1 input source on the TV using the INPUT button on the remote control.
!
NOTE
A DVI to HDMI cable or adapter is required for this connection. DVI doesn't support audio, so a separate audio connection is necessary. 18 Zenith.book Page 19 Wednesday, April 2, 2008 11:46 AM DVD SETUP Component Connection 1. How to connect Connect the video outputs (Y, PB, PR) of the DVD to the COMPONENT IN VIDEO 1 jacks on the TV. Match the jack colors
(Y = green, PB = blue, and PR = red). Connect the audio outputs of the DVD to the COMPONENT IN AUDIO 1 jacks on the TV. 2. How to use
Turn on the DVD player, insert a DVD.
Select the Component 1 input source on the TV using the INPUT button on the remote control.
If connected to COMPONENT IN2 input, select the Component 2 input source on the TV.
Refer to the DVD player's manual for operating instructions. E X T E R N A L E Q U P M E N T S E T U P I Component Input ports To get better picture quality, connect a DVD player to the component input ports as shown below. Component ports on the TV Video output ports on DVD player Y Y Y Y Y PB PB B-Y Cb Pb PR PR R-Y Cr Pr 19 Zenith.book Page 20 Wednesday, April 2, 2008 11:46 AM EXTERNAL EQUIPMENT SETUP E X T E R N A L E Q U P M E N T S E T U P I S-Video Connection 1. How to connect Connect the S-VIDEO output of the DVD to the S -VIDEO input on the TV. Connect the audio outputs of the DVD to the AUDIO input jacks on the TV. 2. How to use
Turn on the DVD player, insert a DVD.
Select the AV 1 input source on the TV using the INPUT button on the remote control.
If connected to AV IN2, select AV 2 input source.
Refer to the DVD player's manual for operating instructions. HDMI Connection 1. How to connect Connect the HDMI output of the DVD to the HDMI/DVI IN 1 or HDMI IN 2 jack on the TV. No separated audio connection is necessary. HDMI supports both audio and video. 2. How to use
Select the HDMI1 or HDMI2 input source on the TV using the INPUT button on the remote control.
Refer to the DVD player's manual for operating instructions. HDMI-DVD OUTPUT 20 Zenith.book Page 21 Wednesday, April 2, 2008 11:46 AM VCR SETUP
To avoid picture noise (interference), leave an adequate distance between the VCR and TV.
If the 4:3 picture format is used; the fixed images on the sides of the screen may remain visible on the screen. This phenomenon is common to all TVs and is not covered by warranty. Antenna Connection Wall Jack Antenna 1. How to connect Connect the RF antenna out socket of the VCR to the ANTENNA/CABLE IN socket on the TV. Connect the antenna cable to the RF antenna in socket of the VCR. 2. How to use
Set VCR output switch to 3 or 4 and then tune TV to the same channel number.
Insert a video tape into the VCR and press PLAY on the VCR. (Refer to the VCR owners manual.) E X T E R N A L E Q U P M E N T S E T U P I 21 Zenith.book Page 22 Wednesday, April 2, 2008 11:46 AM EXTERNAL EQUIPMENT SETUP E X T E R N A L E Q U P M E N T S E T U P I Composite (RCA) Connection 1. How to connect Connect the AUDIO/VIDEO jacks between TV and VCR. Match the jack colors (Video = yellow, Audio Left
= white, and Audio Right = red) 2. How to use
Insert a video tape into the VCR and press PLAY on the VCR.
(Refer to the VCR owners manual.)
Select the AV 1 input source on the TV using the INPUT button on the remote control.
If connected to AV IN2, select AV 2 input source.
!
NOTE
If you have a mono VCR, connect the audio cable from the VCR to the AUDIO L/MONO jack of the set. S-Video Connection 1. How to connect Connect the S-VIDEO output of the VCR to the S -VIDEO input on the TV. Connect the audio outputs of the VCR to the AUDIO input jacks on the TV. 2. How to use
Insert a video tape into the VCR and press PLAY on the VCR.
(Refer to the VCR owners manual.)
Select the AV 1 input source on the TV using the INPUT button on the remote control.
If connected to AV IN2, select AV 2 input source. NOTE
!
S-Video provides better quality than composite. Use it when available. 22 CAUTION
Do not connect to both Video and S-Video at the same time. In the event that you connect both Video and the S-Video cables, only the S-Video will work. Zenith.book Page 23 Wednesday, April 2, 2008 11:46 AM OTHER A/V SOURCE SETUP 1. How to connect Camcorder jacks Connect the AUDIO/VIDEO between TV and external equipment. Match the jack colors.
(Video = yellow, Audio Left = white, and Audio Right = red) 2. How to use
Select the AV 2 input source on the TV using the INPUT button on the remote control.
If connected to AV IN1 input, select AV 1 input source.
Operate the corresponding external equipment. Video Game Set E X T E R N A L E Q U P M E N T S E T U P I 23 Zenith.book Page 24 Wednesday, April 2, 2008 11:46 AM EXTERNAL EQUIPMENT SETUP PC SETUP This TV provides Plug and Play capability, meaning that the PC adjusts automatically to the TV's settings. VGA (D-Sub 15 pin) Connection 1. How to connect Connect the VGA output of the PC to the RGB (PC) jack on the TV. Connect the PC audio output to the AUDIO (RGB/DVI) jack on the TV. 2. How to use
Turn on the PC and the TV.
Select the RGB-PC input source on the TV using the INPUT button on the remote control. E X T E R N A L E Q U P M E N T S E T U P I 24 Zenith.book Page 25 Wednesday, April 2, 2008 11:46 AM DVI to HDMI Connection E X T E R N A L E Q U P M E N T S E T U P I 1. How to connect Connect the DVI output of the PC to the HDMI/DVI IN 1 jack on the TV. Connect the PC audio output to the AUDIO (RGB/DVI) jack on the TV. 2. How to use
Turn on the PC and the TV.
Select the HDMI1 input source on the TV using the INPUT button on the remote control. 25 Zenith.book Page 26 Wednesday, April 2, 2008 11:46 AM EXTERNAL EQUIPMENT SETUP NOTES
!
To get the the best picture quality, adjust the PC graphics card to 1366x768.
Depending on the graphics card, DOS mode may
Avoid keeping a fixed image on the screen for a long period of time. The fixed image could become permanently imprinted on the screen. not work if a HDMI to DVI Cable is in use.
The synchronization input form for Horizontal and
In PC mode, there may be noise associated with Vertical frequencies is separate. the resolution, vertical pattern, contrast or brightness. If noise is present, change the PC output to another resolution, change the refresh rate to another rate or adjust the brightness and contrast on the PICTURE menu until the picture is clear.
Depending on the graphics card, some resolution settings may not allow the image to be positioned on the screen properly. Supported Display Specifications RGB-PC, HDMI1/DVI-PC mode Resolution Horizontal Frequency (KHz) Vertical Frequency (Hz) 640x350 720x400 640x480 800x600 31.469 31.469 31.469 37.879 1024x768 48.363 1280x768 1360x768 1366x768 47.776 47.720 47.130 70.08 70.08 59.94 60.31 60.00 59.87 59.799 59.65
* RGB-PC mode only
* LCD TV only E X T E R N A L E Q U P M E N T S E T U P I 26 Zenith.book Page 27 Wednesday, April 2, 2008 11:46 AM Screen Setup for PC mode Overview When the RGB input of the set is connected to a PC Output, Select RGB-PC with using the INPUT button on the remote control. When you change the resolution, select the proper resolution input to see the best picture appearance. in present Adjustment for screen Resolution, Position, Size, and Phase Press the ADJUST button and then use or button to select Resolution, Position, Size, or Phase. Press the ENTER button and then use button to make appropriate adjustments.
The Phase adjustment range is -16 ~ +16.
The Size adjustment range is -30 ~ +30. Press the ENTER button. Resolution 1024 x 768 1280 x 768 1360 x 768 1366 x 768 Resolution Size Phase Reset MENU Prev Select Ok Resolution This function allows you select Position Size Phase function resolution of XGA/WXGA. This is to adjust picture to left/right and up/
down as you prefer. This function is to minimize any vertical bars or stripes visible on the screen background. And the horizontal screen size will also change. This function allows you to remove any horizontal noise and clear or sharpen the image of characters. E X T E R N A L E Q U P M E N T S E T U P I 27 Zenith.book Page 28 Wednesday, April 2, 2008 11:46 AM EXTERNAL EQUIPMENT SETUP Initializing (Reset to original factory values) To initialize the adjusted values. Press the ADJUST button and then use or button to select Reset. Press the ENTER button and then use or button to select Yes. Press the ENTER button. Resolution Position Size Phase Reset Initialize Settings. Yes No MENU Prev Select Ok
You can also use the PICTURE menu to adjust Screen. Picture Mode Color Temperature
: User1
: Cool DB Advanced Aspect Ratio Picture Reset Screen
: 16:9 Picture Mode Color Temperature DB Advanced Aspect Ratio Picture Reset Screen Selection ( or screen adjustment menu.
) leads you to the E X T E R N A L E Q U P M E N T S E T U P I 28 Zenith.book Page 29 Wednesday, April 2, 2008 11:46 AM AUDIO OUT CONNECTION Send the TVs audio to external audio equipment via the Audio Output port. Analog 1. How to connect Connect audio outputs to the TVs AUDIO OUT jacks. Set the TV Speaker option - Off in the AUDIO menu.
(p.53). See the external audio equipment instruction manual for operation. Digital 1. How to connect Connect one end of the optical cable to the TVs DIGITAL AUDIO OUT OPTICAL. Connect the other end of the optical cable to the digital audio input on the audio equipment. Set the TV Speaker option - Off in the AUDIO menu.
(p.53). See the external audio equipment instruction manual for operation. NOTE
!
When connecting with external audio equipments, such as amplifiers or speakers, you can turn the TV speakers off in the menu. (p.53) CAUTION
Do not look into the optical output port. Looking at the laser beam may damage your vision.
Block the SPDIF out (optical) about the contents with ACP(Audio Copy Protection) function. E X T E R N A L E Q U P M E N T S E T U P I 29 Zenith.book Page 30 Wednesday, April 2, 2008 11:46 AM WATCHING TV / CHANNEL CONTROL REMOTE CONTROL FUNCTIONS When using the remote control, aim it at the remote control sensor on the TV. TV/STB/DVD/
VCR Select the remote operating mode: TV, STB, DVD, or VCR. POWER Turns your TV or any other programmed equipment on or off, depending on the mode. RETURN Clear all on-screen displays and return to TV viewing from any menu. MENU Displays the main menu. Clear all on-screen displays and return to TV viewing from any menu. INPUT External input modes rotate in regular sequence. VOLUME UP/DOWN Increase/decrease the sound level. FAV Scroll through the programmed Favorite channels. p.36 MUTE Switch the sound on or off. p.32 CHANNEL UP/DOWN Select available channels. PAGE UP/DOWN Move from one full set of screen information to the next one. NUMBER button
- (DASH) Used to enter a program number for multiple program channels such as 2-1, 2-2, etc. FLASHBK Tune to the last channel viewed. VCR/DVD Control buttons Control video cassette recorders or DVD players. I W A T C H N G T V
/
C H A N N E L C O N T R O L 30 Zenith.book Page 31 Wednesday, April 2, 2008 11:46 AM THUMBSTICK
(Up/Down/Left Right/ENTER) Navigate the on-screen menus and adjust the system settings to your preference. BRIGHT -/+ Adjust the brightness on screen. TIMER Select the amount of time before your TV turns off automatically. p.64 ADJUST Adjust the screen resolution, position, size and phase. p.27-28 PICTURE Selects the factory preset picture depend on the viewing environment. p.41 SOUND Selects the factory preset sound for type of program. p.50 SAP Analog mode: Selects MTS sound (Mono, Stereo, or a SAP) p.54 DTV mode: Changes the audio language. CC Select a closed caption. p.57 I W A T C H N G T V
/
C H A N N E L C O N T R O L Installing Batteries
Open the battery compartment cover on the back side and install the batteries matching correct polarity (+with +, -with -).
Install two 1.5V AAA batteries. Dont mix old or used batteries with new ones.
Close cover. 31 Zenith.book Page 32 Wednesday, April 2, 2008 11:46 AM WATCHING TV / CHANNEL CONTROL TURNING ON TV First, connect power cord correctly. At this moment, the TV switches to standby mode.
In standby mode to turn TV on, press the button on the TV or press the POWER, INPUT, CH (
Number (0~9) button on the remote control.
, INPUT, CH ( or )
), or I W A T C H N G T V
/
C H A N N E L C O N T R O L Select the viewing source by using the INPUT button on the remote control.
This TV is programmed to remember which power state it was last set to, even if the power cord is out. When finished using the TV, press the POWER button on the remote control. The TV reverts to standby mode. NOTE
!
If you intend to be away on vacation, disconnect the power plug from the wall power outlet. CHANNEL SELECTION Press the CH (
or
) or NUMBER buttons to select a channel number. VOLUME ADJUSTMENT Adjust the volume to suit your personal preference. Press the VOL (+ or -) button to adjust the volume. If you want to switch the sound off, press the MUTE button. You can cancel the Mute function by pressing the MUTE or VOL (+ or -) button. 32 Zenith.book Page 33 Wednesday, April 2, 2008 11:46 AM ON-SCREEN MENUS SELECTION Your TV's OSD (On Screen Display) may differ slightly from what is shown in this manual. Press the MENU button and then use or button to select each menu. Press the button and then use button to display the available menus. SETUP PICTURE Auto Tuning Manual Tuning Channel Edit LOCK AUDIO
: Off Lock System Set Password Block Channel Movie Rating TV Rating-Children TV Rating-General Downloadable Rating Input Block Picture Mode Color Temperature
: User1
: Cool DB Advanced Aspect Ratio Picture Reset Screen
: 16:9 Sound Mode Auto Volume Balance TV Speaker
: Standard
: On
: 0
: On OPTION TIME Language Input Label Key Lock Caption Set ID
: English
: Off
: Off
: 1 Clock Off Time On Time Sleep Time Auto Sleep
: Oct 19, 2006, 03:44 AM
: Off
: Off
: Off
: Off I W A T C H N G T V
/
C H A N N E L C O N T R O L 33 Zenith.book Page 34 Wednesday, April 2, 2008 11:46 AM WATCHING TV / CHANNEL CONTROL CHANNEL SETUP Auto Scan (Auto Tuning) Automatically finds all channels available through antenna or cable inputs, and stores them in memory on the channel list. Run Auto Tuning again after any Antenna/Cable connection changes. A password is required to gain access to Auto Tuning menu if the Lock System is turned on. Press the MENU button and then use to select the SETUP menu. or button Auto Tuning Manual Tuning Channel Edit Press the select Auto Tuning. button and then use or button to Press the ENTER button to begin the channel search. Allow Auto Tuning to complete the channel search cycle for ANTENNA and CABLE. NOTE DTV (Digital DTV antenna) TV (Analog TV antenna) CADTV (Digital CADTV cable) CATV (Analog CATV cable) Auto Tuning Manual Tuning Channel Edit Selection ( or to the Auto Tuning screen.
) leads you Auto Tuning Manual Tuning Channel Edit Processing Auto Tuning. Selection ( or to the Auto Tuning screen.
) leads you DTV Ch.23 Found Channel(s): 16 to stop the current Press scan and start ANALOG ANTENNA channel scan. Next MENU Prev I W A T C H N G T V
/
C H A N N E L C O N T R O L 34 Zenith.book Page 35 Wednesday, April 2, 2008 11:46 AM Add/Delete Channel (Manual Tuning) A password is required to gain access to Manual Tuning menu if the Lock System is turned on. If selecting DTV or CADTV input signal, you can view the on-screen signal strength monitor to see the quality of the signal being received. Press the MENU button and then use to select the SETUP menu. or button Auto Tuning Manual Tuning Channel Edit Press the select Manual Tuning. button and then use or button to Press the button and then use select TV, DTV, CATV, and CADTV. or button to Press the or select channel you want to add or delete. button and then use button to Press the ENTER button to add or delete the channel. Press RETURN button to return to TV viewing or press MENU button to return to the previous menu. Auto Tuning Manual Tuning Channel Edit Select channel type and RF-channel number. DTV 2 Auto Tuning Manual Tuning Channel Edit Select channel type and RF-channel number. DTV 12 DTV 12-0 Bad Normal Good Press to delete the channel. I W A T C H N G T V
/
C H A N N E L C O N T R O L 35 Zenith.book Page 36 Wednesday, April 2, 2008 11:46 AM WATCHING TV / CHANNEL CONTROL Channel Editing From the default channel list created from the Auto Tuning channel search, you can create two different types of channel lists in memory: custom list and favorite channel list. A custom list can be created by toggling each channel on or off with ENTER button. The channels in the Custom List are displayed in black and the channels deleted from the Custom List are displayed in gray. Once a channel is highlighted you can add or delete the channel by referring to the small window at the top-left corner of the screen. You can create your own Favorite List. Use the FAV button on the remote control when a channel is highlighted and then add or delete the channel to/from your Favorite List. Press the MENU button and then use to select the SETUP menu. or button Press the select Channel Edit. button and then use or button to Press the with channel numbers and a preview picture. button. You will now see a screen filled Auto Tuning Manual Tuning Channel Edit Auto Tuning Manual Tuning Channel Edit Selection ( or to the Auto Tuning screen.
) leads you I W A T C H N G T V
/
C H A N N E L C O N T R O L Use button to select a channel and then use the ENTER button to add or delete it. Press FAV button to add the channel to the Favorite List. The surfing icon will appear in front of that channel number. Press RETURN button to return to TV viewing or press MENU button to return to the previous menu. 36 Zenith.book Page 37 Wednesday, April 2, 2008 11:46 AM INPUT LIST Press the INPUT button to display external device that is connected to the unit, on screen. Press the ENTER button to change the input to the active external device. Use the or button to select the input source. AV 2 Input List Antenna Cable AV 1 AV 2 Component 1 If all external input sources are connected:
Antenna Cable AV 1 AV 2 Component 1 HDMI2 HDMI1 RGB-PC Component 2 If no external input sources are not connected:
Antenna Cable If there is any external input source connected:
(ex: When connected only to AV 2) Antenna Cable AV 2
Antenna: Select it to watch over-the-air broadcasts.
Cable: Select it to watch cable and digital cable.
AV 1-2: Select them to watch a VCR or other external equipment.
Component 1-2: Select them to watch DVD or a Digital set-top box.
RGB-PC: Select it to view PC input.
HDMI1-2: Select them to watch high definition devices. I W A T C H N G T V
/
C H A N N E L C O N T R O L 37 Zenith.book Page 38 Wednesday, April 2, 2008 11:46 AM WATCHING TV / CHANNEL CONTROL INPUT LABEL You can set a label for each input source when it's not in use. I W A T C H N G T V
/
C H A N N E L C O N T R O L button and then use Press the button to select the source: AV 1, AV 2, Component 1, Component 2, RGB-PC, HDMI1, or HDMI2. or Press the or button to select the label. Press RETURN button to return to TV viewing or press MENU button to return to the previous menu. 38 Press the MENU button and then use to select the OPTION menu. or button Press the select Input Label. button and then use or button to Language Input Label Key Lock Caption Set ID
: English
: Off
: Off
: 1 Language Input Label Key Lock Caption Set ID AV 1 AV 2 Component 1 Cable Box VCR DVD Component 2 Set Top Box RGB-PC HDMI1 HDMI2 VCR Game Satellite
This product uses the FCC Data API but is not endorsed or certified by the FCC