FCC ID: BEJL02A PCS GSM/ WCDMA USB Modem

Part 15.21 statement

" Change or Modifications that are not expressly approved by the manufacturer could void the user's authority to operate the equipment. "

Part 15.105 statement This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. if this equipment does cause harmful interference or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected

- Consult the dealer or an experienced radio/TV technician for help. Body-worn Operation This device was tested for typical body-worn operations with the USB modem kept 0.19 inches (0.5cm) between the users body. To comply with FCC RF exposure requirements, a minimum separation distance of 0.19 inches(0.5cm) must be maintained between the user's body and the USB modem. For Your Safety FCC RF Exposure Information WARNING! Read this information before operating the USB modem. In August 1996, the Federal Communications (FCC) of he United States, with its action in Report and Order FCC 96-326, adopted an updated safety standard for human exposure to radio frequency (RF) electromagnetic energy emitted by FCC regulated transmitters. Those guidelines are consistent with the safety standard previously set by both U.S. and international standards bodies. The design of this phone complies with the FCC guidelines and these international standards. CAUTION Use only the supplied and approved antenna. Use of unauthorized antennas or modifications could impair call quality, damage the phone, void your warranty and/or result in violation of FCC regulations. Do not use the phone with a damaged antenna. If a damaged antenna comes into contact with skin, a minor burn may result. Contact your local dealer for a replacement antenna. 10 Your mobile phone is a radio transceiver, designed and manufactured not to exceed the SAR*

limits** for exposure to radio-frequency (RF) energy, which SAR* value, when tested for compliance against the standard was W/kg. While there may be differences between the SAR* levels of various phones and at various positions, they all meet*** the EU requirements for RF exposure. The exposure standard for mobile phones employs a unit of measurement known as the Specific Absorption Rate, or SAR. The SAR limit for mobile phones used by the public is 2.0 watts/kilogram (W/kg) averaged over ten grams of tissue, recommended by The Council of the European Union. The limit incorporates a substantial margin of safety to give additional protection for the public and to account for any variations in measurements. Tests for SAR have been conducted using standard operating positions with the phone transmitting at its highest certified power level in all tested frequency bands. Although the SAR is determined at the highest certified power level, the actual SAR level of the phone while operating can be well below the maximum value. This is because the phone is designed to operate at multiple power levels so as to use only the power required to reach the network. In general, the closer you are to a base station antenna, the lower the power output. Technical Data Ambient Temperatures Max: +55C Min: -10C Contents

-How to Read/Refer to This Manual

-Features of the L-02A

-Safety Precautions (ALWAYS FOLLOW THESE PRECAUTIONS)

-Handling and Care

-Purchased Product and Accessories

-Before Using the FOMA Terminal Names of Parts and Functions 4 FOMA Card Available Communications Inserting the FOMA Terminal into a PC

-Setting Up Setting Up Installing Communication Configuration Files (Drivers) into Windows Installing Communication Configuration Files (Drivers) into Macintosh Uninstalling Communication Configuration Files (Drivers)

-Using L-02A Connection Manager About L-02A Connection Manager Installing L-02A Connection Manager (Drivers) Using Packet Communication Using SMS Using Phonebook Using Application Option Uninstalling L-02A Connection Manager

-DOCOMO Connection Manager DOCOMO Communication Settings flow using DOCOMO Connection Manager Start up DOCOMO Connection Manager Uninstalling DOCOMO Connection Manager Communication Settings without using DOCOMO Connection Manager

-Overseas Use International Roaming Service (WORLD WING) Services Available Overseas Sending the Message in Japan to Overseas Before Using Overseas Setting the Searching Method for Available Networks

-Appendix AT Commands AT Command List Troubleshooting 5 Error Messages Warranty and After-Sales Service Export Controls of the Product and Accessories Main Specifications Intellectual Property Rights Index 6

CON_Guide_E.book 53 Instruction Manual for Connection Guide Data Communication Device L-02A CON_Guide_E.book 54 DOCOMO W-CDMA GSM/GPRS System Thank You for Purchasing theData Communica-

tion Device L-02A Before or while using the L-02A, be sure to thoroughly read this manual and the individual manual for other operation devices to ensure its correct use. For further information, contact the "docomo Information Center" on the back of this manual. The L-02A is designed to be your close partner. Treat it carefully at all times to ensure longterm performance. Before Using the FOMA Terminal Because the FOMA terminal uses radio waves, it may not function in locations where it is difficult for radio waves to penetrate, such as tunnels, underground passages and some buildings in areas where radio wave signals are weak or out of the service area. Even when you are on a higher floor of a tall building or condominium and nothing blocks your view outside, the FOMA terminal may not be able to receive or transmit signals. Also communication may be interrupted even when the Antenna Indication Lamp on the FOMA terminal lights green indicating a strong signal reception with 3 antenna indication bar.

Use the FOMA terminal in ways that do not disturb others in public places, crowded locations, or quiet locations.

The FOMA terminal communicates via radio waves by converting voices into digital signals. If you move into an area where signal reception is poor, the digital signals may not be accurately decoded and what you hear may differ slightly from what was actually said. 54

DOCOMO is not responsible for any economic losses incurred through lost communication opportunities caused by external factors such as malfunction or failure of the FOMA terminal, or electrical outage.

The FOMA terminal can be operated in FOMA Plus-Areas and FOMA HIGH-SPEED Areas.

The FOMA terminal can be used only via the FOMA network provided by DOCOMO and DOCOMO's roaming area.

This FOMA terminal does not support i-mode functions (i-mode mail, connection to official i-mode sites or i-appli, etc.) For Those Who Use the FOMA Terminal for the First Time If this is the first time for you to use the FOMA terminal, it is recommended that you read this manual in the following order to learn basic operations. 1. Learning the precautions. P61 2. Learning the names of parts and functions of the FOMA terminal. P72 3. Inserting the FOMA terminal into a PC . P77 4. Having the FOMA terminal recognized by your PC. P77 5. Setting up the FOMA terminal for communication

. "L-02A INSTRUCTION MANUAL" P60 The latest version of this manual can be downloaded from the DOCOMO web site. The URL of PDF for Instruction Manual http://www.nttdocomo.co.jp/english/support/manual/

index.html The URL and the information contained in the manual are subject to change without prior notice. CON_Guide_E.book 55 How to Read/Refer to This Manual Contents L-02A Manual is composed ofL-02A Instruction ManualConnection Guide(this manual) and L-02A INSTRUCTION MANUAL (included CD-ROM) recorded in CD-ROM. L-02A Instruction ManualConnection Guidethis manual The following contents such as connection to computer, troubleshooting methods, specifications of L-02A are written.

Contents/Precautions

Before Using the FOMA Terminal

Setting up

Appendix/Troubleshooting L-02A INSTRUCTION MANUAL (included CD-ROM) Besides the above contents described inL-02A Instruction ManualConnection Guide, the contents of configuring communication through special application are also written. This manual is supplied with PDF. To view this manual, Adobe Reader (Version6.0 or later is recommended) is necessary.

L-02A Connection Software

DOCOMO Connection Manager

Configuring Network Manually

Overseas Use 55 CON_Guide_E.book 56 How to Refer to This Manual This manual offers you the following methods to easily find a page describing functions or services you want to know about. See next page for detailed descriptions From the Index P109 Search from the index when you know the names of functions or services. From the Tabs on the Cover Front cover Search functions or services from the index tabs printed on the front cover. From the Contents Search from the contents that categorize functions. From the Main Features P59 P60 Search from the features when you want to use specific functions. Please understand thatL-02A Manual refers to theL-02Aas theFOMA Terminal. This manual describes, some steps and screens may differ depending on your operating environment. Reprinting all or parts of this manual is prohibited. Information contained in this manual is subject to change without prior notice. 56 CON_Guide_E.book 57 A way to find a destination page is explained with an example of "Installing L-02A connection software on Windows

(including a driver)"

From the Index

P109 Search or a function name or a service name as shown below. From the Index Tabs on the Front Cover

Front cover Search for the function in the order of Front cover Chapter title page Target pageas shown below. P85 The page describing

"Installing L-02A connection software on Windows

(including a driver)"

57 CON_Guide_E.book 58 Displays a section title. Useful Information or suggestions relating to an operation. Explains Operation steps A key screen for an operation step. This is an image of a screen seen on the PC. Numbers, settings or characters entered are for reference only. The above page is an example. Screen images and illustrations contained in this manual are for reference only. They may differ from those seen for the actual product. Index:

Searching each chapter is available. 58 CON_Guide_E.book 59 Appendix/

Trouble-

shooting 97 Troubleshooting Error Messages Warranty and After-Sales Service Software update Main Specifications Export Controls of the Product and Accessories Intellectual Property Rights Index Contents How to Read/Refer to This Manual 55 Contents 59 Features of the L-02A 60 Safety Precautions (ALWAYS FOLLOW THESE PRECAUTIONS) 61 Handling and Care 66 Purchased Product and Accessories 69 Before Using the FOMA Terminal 71 Setting Up 81 Names of Parts and Functions Using FOMA Card Available Communications Connecting the FOMA Terminal with a PC Setting Up Installing L-02A Connection Soft-

ware on Windows (including a driver) Installing L-02A Connection Soft-

ware on Macintosh (including a driver) Uninstalling L-02A Connection Soft-

ware (including a driver) Contents/Precautions 59 CON_Guide_E.book 60 FOMA (Freedom Of Mobile multimedia Access) is the name of a service provided by DOCOMO based on the W-CDMA system, which is certified as one of the global standards of 3rd generation mobile communication systems (IMT-2000). Features of the L-02A Correspondence with the FOMA HIGH-SPEED Area You can enjoy high speed communication (Best effort systemat a maximum of 7.2Mbps for receiving and 384kbps for sending.

The maximum speed of 7.2Mbps for receiving and 384kbps for sending are theoretical values and they do not show the actual performance.

Out of High-Speed area, the maximum communication speed for receiving and sending is 384kbps.

The actual communication speed varies depending on surrounding communication conditions and network condition.

DOCOMO offers Internet connection services, such as mopera U. For details, visit the mopera U web site http://www.mopera.net/ (Japanese only) The packet communication in FOMA HIGHSPEED area, the amount of send/receive data is expected to increase. Note that the communication fees may become high. FOMA Card Interchangeability The same FOMA card can be used in more than one FOMA terminal.P74 SMS Feature Allows you to send and receive SMS by using L-02A Connection Software "L-02A INSTRUCTION MANUAL" P48

Up to 20 simultaneous multi-messaging can be supported. Note that fees for multi-messaging will be charged depending on the number of SMS you send. International Roaming Service Communications are available from a PC even in foreign countries that have adapted the W-CDMA (3G) network system or GPRS network.

"L-02A INSTRUCTION MANUAL" P108 If you subscribed to the FOMA service after September1,2005 a separate subscription is not required to use WORLD WING. If you subscribed to the FOMA service on or before August 31, 2005 and have not subscribed to WORLD WING, a separate subscription is required to use it. 60 Contents/Precautions CON_Guide_E.book 61 The following symbols indicate special warnings regarding product usage. Denotes things not to do (prohibition). Not disassembly Not liquids Denotes not to disassemble. Denotes not to use where it could get wet. Denotes mandatory instructions

(matters that must be complied with).

"Safety Precautions" are explained in the following 4 sections. General Precautions for the FOMA Terminal and FOMA Card 62 Precautions for the FOMA Terminal 63 Precautions for the FOMA Card 64 Notes on Using near Electronic Medical Equipment 65 Safety Precautions (ALWAYS FOLLOW THESE PRECAUTIONS)

Before using your FOMA terminal, read these Safety Precautionscarefully so that you can use it properly. After reading the safety precautions, keep this manual in a safe place for later reference.

These precautions are intended to protect you and others around you. Read and follow them carefully to avoid injury, damage to the product or damage to property. The signs below indicate the levels of danger or damage that may occur if the particular precautions are not observed . DANGER WARNING CAUTION This sign indicates that incorrect handling has a high possibility of causing death or serious injury. This sign indicates that incorrect handling poses a risk of causing death or serious injury. This sign indicates that incorrect handling poses a risk of causing injury or damage to the product or property. Contents/Precautions 61 CON_Guide_E.book 62 General Precautions for the FOMA Terminal and FOMA Card DANGER Do not use or leave the FOMA terminal and FOMA card in places with a high temperature such as in cars under the blazing sun. Deformation, malfunction heating or the deterioration of performance may result. Also, part of the case could get heated, causing bare skin burns. Do not disassemble Disassemble, remodel or solder the terminal and FOMA card. Fire, injury, electric shock or malfunction may result. Do not let FOMA terminal and FOMA card get wet. Contact with water or other liquids may cause heating, electric shock, fire, malfunction or injury. Take care not to use the terminal and FOMA card in areas where they could get wet. Not disassembly Not liquids 62 Contents/Precautions WARNING Do not put the FOMA terminal or FOMA card in microwave ovens or other heating. The FOMA terminal may over heat, smoke or catch fire, or its circuit parts may burst. Do not throw the FOMA terminal or FOMA card, or subject them to severe shocks. Malfunction or fire may result. Be careful not to let electro conductive materials (metal pieces, pencil leads etc.) contact with the connector terminal. Also, make sure that these are not entered into the inside of the FOMA terminal. Fire or other malfunctions may result from a short circuit. Make sure you have the power of the computer which is connected with FOMA terminal switched off before you go near a flammable gas such as gasoline fumes. Using the terminal in such an environment may result in a fire. CON_Guide_E.book 63 CAUTION Do not place the FOMA terminal or FOMA card on unstable locations such as wobbly tables or slanted locations. The FOMA terminal or FOMA card may fall, resulting in injury or malfunction. Do not store the FOMA terminal or FOMA card in humid or dusty places, or in hot areas. Malfunction may result. If children use the FOMA terminalFOMA terminal or FOMA card, a guardian should explain the precautions and correct operations. The guardian should also make sure that the instructions are followed during use. Injury may result. Keep out of reach of babies and infants. Accidental swallowing or injury may result. Precautions for the FOMA Terminal WARNING Do not put the FOMA terminal in the place where it could be affected by an expanded airbag, e.g. on the dashboard. If the airbag expands, the FOMA terminal could hit you and others, causing accidents such as injury and the FOMA terminal could get malfunction or damaged. Do not place the terminal in breast or inner pocket when electronic medical equipment is near by. Using FOMA terminal closed to electronic medical equipment may result malfunction. Do not allow liquids such as water, or foreign materials such as metal pieces or flammable materials to get into the FOMA card opening in the FOMA terminal. Fire, electronic shock or malfunction may result. Contents/Precautions 63 CON_Guide_E.book 64 Turn off the FOMA terminal in places where use is prohibited such as airplanes or hospitals. Electronic and electronic medical appliances may be adversely affected. For use inside medical facilities, make sure that you comply with their regulations. Remove FOMA terminal from the USB port in places near high-precision electronic devices or devices using weak electronic signals. The FOMA terminal may possibly cause these devices to malfunction. Electronic devices that may be affected Hearing aids, implanted cardiac pacemakers, implanted defibrillators, other medical electronic devices, fire alarms, automatic doors and other automatically controlled devices. If you are using an implanted cardiac pace maker, implanted defibrillator or any other electronic medical device, consult the manufacturer or retailer of the device for advice regarding possible effects from radio waves. CAUTION Electronic devices in some types of cars can be affected by use of the FOMA terminal. For safety's sake, do not use the FOMA terminal inside such cars. Itching, rash or eczema may be caused depending on your physical conditions or predisposition. If an abnormality occurs, stop using the FOMA terminal immediately, and then seek medical attention. Metal(chrome plating) is used to the following parts. Parts that are used: USB connector Precautions for the FOMA Card CAUTION Be careful when removing the FOMA card(IC portion). Your hands or fingers may be injured. 64 Contents/Precautions CON_Guide_E.book 65 Notes on Using near Electronic Medical Equipment The description below meets Guideline on the Use of Radio-communication Equipment such as Cellular Telephones - Safeguards for Electronic Medical Equipment by the Electromagnetic Compatibility Conference. WARNING Be sure to adhere to the following regulations inside medical facilities. Keep the FOMA terminal out of operating rooms, intensive care units (ICUs) or coronary care units (CCUs). Turn off the PC in hospital wards. Turn off the PC in hospital lobbies and corridors if electrical medical devices could be nearby. If the medical facility has specific zones where use or possession of mobile terminals is prohibited, follow those regulations. If the function which automatically turns on the power is set, cancel the setting before turning off your PC. Turn off the PC in crowded trains or other public places where implanted cardiac pacemaker or defibrillator wearers could be nearby. Signals from the FOMA terminal may affect the operation of implanted cardiac pacemakers or defibrillators. If you use an implanted cardiac pacemaker or implanted defibrillator, use the mobile terminal 22cm or more away from the implanted cardiac pacemaker or implanted defibrillator. Operation of an implanted cardiac pacemaker or implanted defibrillator may be affected by radio waves. Patients using electronic medical equipment other than implanted cardiac pacemakers or implanted defibrillators

(using outside medical facilities for treatment at home, etc.) should check the influence of radio waves upon the equipment by consulting the manufacturer. Operation of electronic medical equipment may be affected by radio waves. Contents/Precautions 65 CON_Guide_E.book 66 Handling and Care General Usage Guidelines Keep the FOMA terminal away from water. The FOMA terminal and FOMA card are not waterproof. Do not use the terminal in places with high humidity such as a bath or where rain may get it wet. If you carry the card close to your body, moisture from sweat may corrode the internal parts causing a malfunction. Note that malfunctions deemed to be caused by water are not covered by the warranty, and may be impossible to repair. Since these malfunctions are not under warranty, even when repair is possible, it will be done at the user's expense. Clean the FOMA terminal with a dry, soft cloth

(Lens cleaning cloth). If the FOMA terminal is wiped with alcohol, paint thinner, benzine or detergent, the printing may disappear or color may fade. Keep the connector contacts clean with a dry, soft cloth. Dirty contacts can result in intermittent connections. Do not place the equipment near air conditioner outlets. Condensation may form due to rapid changes in temperature, and this may corrode internal parts and cause malfunction. Do not place the FOMA terminal where excessive force will be applied to it. If FOMA terminal is inserted to a full bag, or placed in a pocket and sat on, its internal PCBs may be damaged or malfunction. Such damage is not covered by warranty. Read the individual manual attached to the FOMA terminal. FOMA Terminal Avoid using in extremely high or low temperatures. The FOMA terminal should be used within a temperature range from 5 C to 35 C and a humidity range from 45 % to 85 %. FOMA terminal may affect fixed phones, televisions or radios in use nearby. Use as far as possible from such appliances. Keep a separate record of any information stored on the FOMA terminal and store the copies in a safe location. DOCOMO assumes no responsibility for the loss of any of your data. 66 Contents/Precautions CON_Guide_E.book 67 Remove the FOMA terminal from the PC when transporting. Malfunction or damage may result. It is normal for the FOMA terminal to become warm during use. You can continue to use it even when it is warm. Take care not to drop the FOMA terminal when removing the FOMA terminal from the carrying case. When it is not in use, keep the FOMA terminal in its carrying case to keep the connector contacts clean. Dirty contacts may result in intermittent connections. When putting the FOMA terminal in carrying case, keep it away from wet or high temperature place. Pay attention not to put excessive force on the FOMA terminal. Transformation, tarnish, color staining may result. FOMA Card Do not put excessive force on the FOMA card when inserting or removing it into the FOMA terminal. It is normal for the FOMA card to become warm during use. You can continue to use it even when it is warm. Always keep the IC portion of the FOMA card clean. Clean the FOMA card with a soft, dry cloth (Lens cleaning cloth). Be sure to keep a separate note of the information registered to the FOMA terminal. DOCOMO is not responsible for any losses of registered information. Visit DOCOMO shop to return the FOMA card for the environmental purpose. Avoid extreme temperature. Do not scratch, touch carelessly or short circuit the IC portion. Data loss or malfunction may result. Do not drop or give shock to the FOMA card . Malfunction may result. Do not bend or put heavy things on the FOMA card. Malfunction may result. Contents/Precautions 67 CON_Guide_E.book 68 CAUTION Do not use the modified FOMA terminal. Using modified FOMA terminal result in violating the law of Electromagnetic Compatibility. FOMA terminal has been complied with technical standard of wireless equipment stipulated by law of Electromagnetic Compatibility. As for the proof, the technical standard compliance mark, is indicated in the inscription seal. If FOMA terminal is modified by turning the screw to the left to disassemble, technical standard compliance becomes invalid. Please do not use FOMA terminal during the time when technical standard compliance is being invalid, since you are in violation of the law of Electromagnetic Compatibility. 68 Contents/Precautions CON_Guide_E.book 69 Purchased Product and Accessories L-02A Terminal (With Warranty) L-02A CD-ROM L-02A Instruction ManualConnection Guide Carrying Case (Sample) L-02A Connection Software (For Windows/Macintosh

DOCOMO Connection Manager (For Windows/Macintosh

L-02A Communication Configuration File (Drivers)

(For Windows/Macintosh

L-02A INSTRUCTION MANUALPDF Software specifications are subject to change without prior notice. USB Extension Cable (Sample) Use when "USB Extension Cable" is written in this manual. Mounting folder (Sample) Use when "A mounting Folder" is written in this manual. Contents/Precautions 69 CON_Guide_E.book 70 CON_Guide_E.book 71 Before Using the FOMA Terminal Names of Parts and Functions Using a FOMA Card Available Communications Connecting FOMA Terminal to a PC 72 74 76 77 71 CON_Guide_E.book 72 Names of Parts and Functions a b d e c A 2 0

L a Antenna The antenna is inside the FOMA terminal. b USB ConnectorP79 Connection contacts to a PC. c FOMA Card CapP74 Inserts/Removes the FOMA Card. d PWR LampP73 Indicates the power supply conditions. e IDLE/BUSY LampP73 Indicates the FOMA terminal status. 72 Before Using the FOMA Terminal CON_Guide_E.book 73 Mode Indication Lamp a b Operation indicating lamp FOMA terminal Status When powered on Waiting to connect to the FOMA network Packet communication SMS PIN Attempting to communicate Communicating While receiving Opening SMS Sending SMS PIN Lock Waiting to unlock PIN1 aPower Indication Lamp bMode Indication Lamp

Red Red Red Yellow

(Flash) Red Red Red Red

Green Blue

(Flash) Blue Green Green Green

Before Using the FOMA Terminal 73 CON_Guide_E.book 74 Using a FOMA Card The FOMA card is an IC card that stores personal information such as your phone number. Without a FOMA card installed in the FOMA terminal, you cannot use data communication, etc.. For detailed information, refer to FOMA Card Manual. Inserting/Removing Inserting a Pull out the FOMA card cartridge c Insert the cartridge back into the FOMA terminal

Insert as following. IC is faced Removing a Pull out the FOMA card cartridge b Put a FOMA card into the cartridge with IC faced b Take the FOMA card out from the cartridge IC is faced 74 Before Using the FOMA Terminal CON_Guide_E.book 75 Note

Make sure to check the direction of FOMA card. IC

Be careful not to scratch FOMA card's IC parts.

Inserting FOMA card in the reverse direction may cause malfunction. Inserting and removing FOMA card with an excessive force may cause damage to your FOMA card.

Do not remove FOMA card while FOMA terminal is inserted to a PC, it may causes damage to your FOMA card. PIN1 Code You can set PIN codes (Personal Identification Number) for FOMA Card. The default setting for the PIN1 code is

"0000". The PIN1 code is a 4 to 8-digit security code to be entered every time the FOMA terminal is turned on for user verification to prevent any unauthorized use by others. If your FOMA card is set to require a PIN1 code, data communication cannot be performed until the PIN1 is entered. Start the L-02A High Speed Utility and verify the PIN1 code, or set ("L-02A INSTRUCTION MANUAL"

P63)not to verify the PIN1 code in advance. Changing the PIN1 Code You can change the PIN1 code to any number. To prevent any unauthorized use by third parties, change it to your own number. If you improperly enter the PIN1 code 3 times in a row, further entry is locked automatically (PIN lock), so be sure to keep a separate note of the numbers you set.

Entering PIN1 Code/ Changing PIN1 code"L-02A INSTRUCTION MANUAL" P64 PIN Unblocking Code The PIN Unblocking Code is the number used to unblock the PIN1 code. You are notified of your PIN Unblocking Code when you purchase your FOMA terminal. Entering the Unblocking Code (8-digit) unblocks the PIN lock. If you improperly enter the Unblocking Code 10 times in a row, the FOMA card locks automatically, so be sure to keep a separate note of the number. Start up L-02A Connection Software The PIN1 code Verification screen appears Enter PIN1 Code Incorrect entry 3 times in a row Enter Unblocking PIN Code OK Incorrect entry 10 times in a row You can set a new PIN1 code Contact a DOCOMO shop Before Using the FOMA Terminal 75 CON_Guide_E.book 76 FOMA Card Types Please be aware that the FOMA card (Blue) has different functions from the FOMA card (Green/White) as follows:

FOMA card

(Green/White) Up to 20 digits Up to 26 digits FOMA card Function

(Blue) This terminal allows up to 20 digits. The number of digits of a phone number that can be saved to the FOMA card Phonebook WORLD WING Not available Available WORLD WING WORLD WING is DOCOMO's FOMA international roaming service that provides telephone and other types of mobile communications. It allows the subscriber to use the same phone number overseas as in Japan by inserting a FOMA card(green/white) into a FOMA terminal or a mobile phone designed for overseas use.

If you subscribed to the FOMA service after September 1, 2005, a separate subscription is not required. However, if you unsubscribed to the FOMA service subscription or canceled the service, a separate subscription is required. If you initially subscribed to the FOMA service before August 31, 2005 and have not subscribed to "WORLD WING", a separate subscription is required.

This service is not available with some billing plans.

Your FOMA card (green/white) is lost or stolen overseas, contact DOCOMO immediately and temporarily suspend your subscription. For contact information, see "docomo Information Center" on the back of this manual. Call and communication charges after the terminal was lost or stolen are still charged to you. 76 Before Using the FOMA Terminal Available Communications Packet Communication Fees for this communication method are based on the amount of exchanged data. You can perform data communication at a maximum of 7.2Mbps for receiving and 384kbps for transmitting by using a connection that allows FOMA communication such as mopera U, one of DOCOMO's Internet connection services. The maximum speed of 7.2Mbps for receiving and 384kbps for sending is theoretical values and does not show the actual ones. The actual communication speed depends on communication environment and network congestion.

You can perform communication using international roaming undermopera U

Out of High-Speed area, the maximum communication speed for receiving and sending is 384kbps.

The communication speed varies depending on the access point and radio wave status.

The communication speed varies depending on the access point under international roaming.

Use theDOCOMO Connection Managerin the CD-ROM to check the approximate number of transmission bytes and charges under the communication. CON_Guide_E.book 77 Note

Communication fees become high when performing communications with large amount of data such as browsing websites with many graphics or downloading data.

Data communication fees under international roaming differ from those in Japan.

FOMA terminal does not support 64K data communication.

This FOMA terminal does not support Remote Wakeup.

This FOMA terminal does not support FAX communication. Usage Notes Internet service provider fees Fees to an Internet service provider may be required to connect to the Internet. These fees are added to the FOMA service fees and are paid to your Internet service provider directly. For details on connection fees, contact your Internet service provider. You can subscribe to such asmopera U, one of DOCOMO's Internet connection services. Charge for subscribing mopera U is required. For service and connection/settings of mopera, visit themopera web site. http://www.mopera.net/mopera/index.html (Japanese only) User authentication to access networks Depending on the access point, user authentication (ID and password) may be required to connect. If required, enter the ID and password from the dial-up network. The ID and password will be provided by the network administrator of your Internet service provider or the access point. For details, contact your provider or access point network administrator. Requirements for packet communication The following conditions must be met to perform communications using the FOMA terminal. However, a connection may not be established if traffic is heavy at the base station or if radio signals are weak.

The FOMA terminal must be in a FOMA network or DOCOMO's roaming service area.

The access point corresponds to the FOMA packet communication. Connecting FOMA Terminal to a PC When connecting FOMA terminal with computer for the first time, it is required to install L-02A connection software (including a driver). For installing L-02A connection software, refer to "L-02A connection software (including a driver) on Windows"

(P85) or"Installing L-02A connection software (including a driver) on Macintosh".(P90) Before Using the FOMA Terminal 77 CON_Guide_E.book 78 When Using a Mounting Folder

Use a mounting folder and a USB extension cable to fix the FOMA terminal on the top of the PC. a Turn on a PC b Connecting the FOMA terminal using a USB extension cable and a mounting folder as shown below

When inserting the FOMA terminal into a mounting folder, make sure to insert as following. The direction in reverse makes USB extension cable not available to fix. Product label is faced Note Power Indication lamp Mode Indication Lamp

Confirm whether power indication lamp changes to red and mode indication lamp changes to green.

Refer to mounting folder, USB extension cable manual for details. c Start communicating 78 Before Using the FOMA Terminal CON_Guide_E.book 79 While Connecting to a PC Directly It is possible to use FOMA terminal that insert to PC horizontally at USB port.

Removing a End data communication

If the L-02A connection software/DOCOMO connection manager is already running, exit the L-02A connection software/DOCOMO connection manager. Verify that data connection is disconnected. b Remove FOMA terminal pulling it in horizontal.

Remove FOMA terminal by holding USB connector and Note

Putting mistakenly excessive force or shock on FOMA terminal may result damage or malfunction. Caution

If you force to remove FOMA terminal and pull out the USB extension cable, this may result malfunction.

Removing FOMA terminal from USB connector during data communication may suspend data communication and result malfunction or data losses. Before Using the FOMA Terminal 79 CON_Guide_E.book 80 CON_Guide_E.book 81 Setting up Setting up 82 Installing L-02A Connection Software on Windows

(including a driver) 85 Installing L-02A Connection Software on Macintosh

(including a driver) 90 Uninstalling L-02A Connection Software (including a driver) 93 81 CON_Guide_E.book 82 Setting up Data communication with L-02A First, installation of L-02A connection software (including a driver) is required. When installing L-02A connection software, the communication configuration file (including a driver) for recognizing FOMA terminal in PC will also be installed. Although data communication is available with only L-02A connection software, if necessary using it after installing DOCOMO connection manager in addition is also available. Data communication is also available based on configuring manually after installing L-02A connection software. Installation of L-02A connection software Because L-02A has zero installation, when connecting the FOMA terminal to a PC for the first time, the screen of L-02A connection software installation appears automatically. The "Zero installation" is corresponding to Windows Vista/XP/

2000. If zero installation works improperly, install L-02A connection software with the included CD-ROM. In addition, although Macintosh does not support the zero installation feature, installtion continues because the CD-

ROM icon is displayed when connecting the FOMA terminal to a PC. The procedure of setting up is shown on the next page. 82 Setting up CON_Guide_E.book 83 Work Flow of Setting up Connecting the FOMA terminal to a PC P85 Preparing the included CD-ROMP87 Installing L-02A connection software (including a driver) For WindowsP85 For MacintoshP90 L-02A Communication Configuration File (Drivers)P88 Using L-02A connection software Using DOCOMO connection manager Configuring manually(Only Windows) Application option of L-02A connection software

"L-02A INSTRUCTION MANUAL" P60 Installing DOCOMO connection manager For Windows "L-02A INSTRUCTION MANUAL" P73 For Macintosh "L-02A INSTRUCTION MANUAL" P77 Communication configuring manually

"L-02A INSTRUCTION MANUAL" P84 Communication connection with L-02A connection software

"L-02A INSTRUCTION MANUAL" P47 Application option/communication connection with DOCOMO connection manager

DOCOMO connection manager operation manual Communication connecting manually with OS

"L-02A INSTRUCTION MANUAL" P104 Setting up 83 CON_Guide_E.book 84 1 DOCOMO does not guarantee the operation under the supported OS of the OS is changed through update. 2 Required memory or available hard disk space may vary depending on the system environment of a PC. 3 Only Mac with CPU made by Intel Corporation is available. For latest information of operation environment, visit DOCOMO's "international web site"

Note

The software may not work depending on the operating system environment. DOCOMO does not guarantee any operation other than the environment operation described on the left side. Operating Environments Using this FOMA terminal under the following operational environments. Item PC Main Unit Requirement

Available CD-ROM drive to use from PC-AT compatible.

USB port (Comply with Universal Serial Bus Specification Rev1.1/2.0) FOMA terminal does not support high-speed data rate of USB2.0.

DOCOMO is not responsible for any incompatibility of the operation performed through the USB Hub (including USB port available from the monitor, keyboard, etc.)

Display resolution of 800600 pixels, High Color (65.536) or higher is recommended. OS1 Required Memory2 Hard Disk Space2 Windows 2000 SP4 or later (Japanese versions) Windows XP SP2 or later (Japanese versions) Windows Vista SP1 or later (Japanese versions) Mac OS X 10.4.11 (Japanese versions)3 Mac OS X 10.5.5 (Japanese versions)3 Windows 2000 : 64Mbytes or more Windows XP : 128Mbytes or more Windows Vista : 512Mbytes or more Mac OS X 10.4.11512Mbytes or more Mac OS X 10.5.5512Mbytes or more 50Mbytes or more available space 84 Setting up CON_Guide_E.book 85 Installing For Windows Vista a Connect the FOMA terminal with a PC The setup screen of L-02A connection software is automatically displayed by zero installation.

"" screen will be displayed depending on setting.If the screen is displayed, check "

" and select "Launcher.exe"

np Installing L-02A Connection Software on Windows (including a driver) The L-02A connection software only need to be installed when you connect the FOMA terminal to your PC for the first time. Note

Do not remove the FOMA terminal while installing.

Installation may take several minutes depending on the PC you use.

Do not install or uninstall during data communication.

When installing, make sure to install from the account with PC supervisor privileges. An error will occur during installation if you install from the account without these privileges.

For details on setting up PC supervisor privileges, contact your computer manufacturer or Microsoft Corporation. When the Setting up screen of L-02A connection software is not automatically displayed, install with the included CD-ROM (P87) Setting up 85 CON_Guide_E.book 86 b Click "(Allow)" on "

(User account control)" screen For Windows XP/2000

Because "(User account control)"

screen is not displayed, follow the next step c Click "(Next)"

86 Setting up d Click " (I Agree)"

Installation starts. e Click " (Finish)"

Install communication configuration file (Driver) continually. CON_Guide_E.book 87 f Confirm whether the FOMA terminal is recognized by PC On the lower right side of task tray, "

(Device driver software is being installed)" message is displayed, and the FOMA terminal is recognized automatically. For Windows 2000

The warning screen of removing device is displayed which has nothing to do with using continually.

"(A new hardware has been found.)" message is displayed, and the FOMA terminal is recognized automatically. If the FOMA terminal is recognized properly, "

(The device is ready for use)" message is displayed. Installing from CD-ROM For Windows XP

On the lower right side of task tray, "

(A new hardware has been found.)"

message is displayed, and the FOMA terminal is recognized automatically.

If the FOMA terminal is recognized properly, "

(A new hardware has been installed and ready for use.)"

message is displayed. For Windows Vista a After starting a PCInsert the included CD-

ROM into the PC b "(Start)""(All programs)""(Accessory)"Click "

(Specify a file name and run)"

c Enter "<CD-ROM>:WindowsL-

02A StartCD.exe" in "(Name)"

Click "OK"

"" screen will be displayed depending on setting.If the screen is displayed, check "

" and select "Launcher.exe"

d Perform the same operation as the one on the step 2 or later on "Installing (P86)"

Setting up 87 CON_Guide_E.book 88 Confirmation after Installation a Double click L-02A connection software icon When the following screen is displayed, the confirmation of installation finishes. Confirming L-02A Communication Configuration File (Drivers) Confirm whether L-02A Communication Configuration File

(Drivers) is set in a PC. For Windows Vista a Click

"(Start)""

(Control panel)""

(System and maintenance)""

(Device manager)""(Continue)"

For Windows XP Click "(Start)""(Control panel)""(Performance and maintenance)""(System)""

(Device manager)" of "(Hardware)"

tab For Windows 2000 Click "(Start)""(Settings)""

(Control panel)""(System)""

(Device manager)" of "(Hardware)"

tab 88 Setting up CON_Guide_E.book 89 b Click each device display to confirm the driver name installed

Confirm whether the driver name is displayed below "

(COM LPT)(Port (COM and LPT))", "(Modem)"

Note

If FOMA terminal is not recognized through the PC's USB port, try other available USB port. FOMA terminal may not be recognized properly with some USB port of PC.

When communicating data with L-02A connection software, application operation of L-02A is required.

"L-02A INSTRUCTION MANUAL" P60

When communicating data with DOCOMO connection manager without L-02A connection software, installation of DOCOMO connection manager is required."L-02A INSTRUCTION MANUAL" P73

When communicating data with neither L-02A connection software nor DOCOMO connection manager, configure it manually."L-02A INSTRUCTION MANUAL" P84 If use Flat-rate data plan, install DOCOMO connection manager individually.

COM port number differs depending on user and PC. Device name Port

(COM and LPT) Modem Driver name FOMA L02A USB Serial1 Device FOMA L02A USB Serial2 Device FOMA L02A Setting up 89 CON_Guide_E.book 90 c Double click "L-02A

.mpkg (L-02A connection software installer.mpkg)"

Installing L-02A Connection Software on Macintosh (including a driver) When installing L-02A connection software, make sure to finish " (DOCOMO connection manager)" first. Note

Do not remove the FOMA terminal while installing.

When installing, make sure to install from the account with PC supervisor privileges. a Connect the FOMA terminal with a Mac CD-ROM icon is displayed on the desktop. d Click " (Continue)"

If icon is not displayed, insert the included CD-ROM into a Mac. CD-ROM icon is displayed on the desktop. b Double click the CD-ROM icon If use the included CD-ROM, continuously double click

"Mac" "L-02A (L-02A connection software)" in order. 90 Setting up CON_Guide_E.book 91 e Click " (Continue)"

g Click " (Install)"

f Confirm " (The license agreement)". If agree with the content, click "

(I Agree)"

h Enter administrator passwordClick "OK"

Setting up 91 CON_Guide_E.book 92 i "(Continue installing)"Click "(Install)"

Confirmation after Installation a Double click L-02A connection software icon When the following screen is displayed, the confirmation of installation finishes. j Click "(Restart)"

Restart the Mac. Installation finishes. Note

When communicating data with L-02A connection software, application operation of L-02A is required.

"L-02A INSTRUCTION MANUAL" P60 92 Setting up

When communicating data with DOCOMO connection manager without L-02A connection software, installation of DOCOMO connection manager is required."L-02A INSTRUCTION MANUAL" P73 If use Flat-rate data plan, install DOCOMO connection manager individually. CON_Guide_E.book 93 Uninstalling L-02A Connection Software (including a driver)

Before uninstalling, remove the FOMA terminal from the PC.

When uninstalling, make sure to install from the account with PC supervisor privileges. For Windows Vista a

"(Start)"" (All programs)""L-02A (L-02A connection software)"Click "Uninstall"

For Windows XP

" (Start)"" (All programs)""L-

02A (L-02A connection software)"Click

"Uninstall"

For Windows 2000

" (Start)"" (Program)""L-02A

(L-02A connection software)"Click "Uninstall"

b " (User account control)" screenClick "(Allow)"

If "(Cancel)" is clicked, uninstallation will be stopped. For Windows XP/2000

Since " (User account control)"

screen is not displayed, follow the next procedure. c Click " (Uninstall)"

Setting up 93 CON_Guide_E.book 94 d Click " (Finish)"

Uninstallation finishes. For Macintosh When uninstall L-02A connection software, exit "DOCOMO connection manager" first. Insert the included CD-ROM into a Mac CD-ROM icon is displayed on the desktop. a b Double click the CD-ROM icon c Double click "Mac"

94 Setting up CON_Guide_E.book 95 d Double click "L-02A (L-02A connection software)"

f Click "(Uninstall)" "

(Restart)"

e Double click ""

Mac restarts. Uninstall finishes. Setting up 95 CON_Guide_E.book 96 CON_Guide_E.book 97 Appendix/Troubleshooting Troubleshooting 98 Error Messages 100 Warranty and After-Sales Service 102 Updating software 103 Main specifications 104 Export Controls of the Product and Accessories 105 Intellectual Property Rights 107 Index 109 97 CON_Guide_E.book 98 Communication problems Troubleshooting The FOMA terminal is not recognized Symptom Communications are not possible Symptom FOMA terminal is not recognized Check Reinsert the FOMA terminal all the way into the USB port securely. Verify the L-02A Communication Configuration Files (Drivers) for the FOMA terminal functioning properly.P85, P90 Communication may fail and the FOMA terminal cannot be properly recognized and functioned, if the PC is started up or restarted with the FOMA terminal left inserted in it. In this case, remove and reinsert the FOMA terminal. If communication fails even after the FOMA terminal is inserted again, remove it once, restart the PC, then insert the FOMA terminal into the PC again. When connecting the FOMA terminal with a USB port, if data communication is not available without being recognzied, double click the "DOCOMO" icon recognized as a CD drive or start "L-02A connection software" or

"DOCOMO connection manager" to recognize the FOMA terminal as a modem. The FOMA card will not be able to use if PIN1 unlock code is wrongly entered 10 times in a low. For further information, visit DOCOMO shop. 98 Appendix/Troubleshooting Check Verify that signals are received in the service area. In the setting of Send Caller ID does not conform to the provider's instructions, communication may not be performed."L-

02A INSTRUCTION MANUAL" P67, P84 Check if you set the FOMA Card Setting to

"PIN1 unblocking"."L-02A INSTRUCTION MANUAL" P63 If set to (PIN1 Lock), launch the L-02A connection software, then change FOMA card setting to "PIN1 unblocking"."L-02A INSTRUCTION MANUAL" P64 Check the property settings of the modem and the registration of the destination (APN) Problems with AT Commands Symptom

[ERROR]

appears when a command is entered

[OK] does not appear after an AT command is entered. Check Verify that you entered a correct ATcommand. Check the properties of the terminal software to see whether a device other than the FOMA terminal is selected Check the L-02A Communication Configuration Files (Drivers) have been installed and functioned properly. Verify that the commands start with "AT" or

"at". CON_Guide_E.book 99 Other problems Symptom The terminal stopped working suddenly The FOMA terminal is not detected if it is inserted into a USB port while installing the L-

02A Communication Configuration Files (Drivers). Internet connection speed decreased significantly Check Verify that the FOMA CARD is properly inserted to FOMA terminal.P77 Your PC operating environments may have changed because a new peripheral or software was installed. Make a confirmation with manufacturer or maker of accessory or software. Restart the PC with the FOMA terminal inserted into the USB port of a PC. Inserting FOMA terminal directly to a PC may result in deterioration of performance depending on the type of PC, specification and degree of electromagnetic interference. Deterioration of performance may occur to the service areas where W-CDMA/HSDPA/

GSM network are unstable. In this case, move to other area and try to connect again. Appendix/Troubleshooting 99 CON_Guide_E.book 100 Error Messages Error Messages

PINPIN FOMA FOMA FOMA PIN1 PIN1 blockedPIN1 PIN1/3 PIN1PIN1 0123456789 PIN148 Description You are out of service area or available network. You may be out of service area or available network, or network error. Please do network setting again. Communication may fail and the FOMA terminal cannot be properly recognized if the PC is started up or restarted with the FOMA terminal left inserted in it. In this case, remove and reinsert the FOMA terminal. If communication fails even after the FOMA terminal is inserted again, remove it once, restart the PC, then insert the FOMA terminal into the PC again. Contact DOCOMO shop if the same problems persist. You cannot customize setting during data communication. Try again after closing data communication. Two of new PIN1 are not identical each other. New PIN1 you want to change is not matched to the PIN1 you entered for verification purpose. Enter correct PIN1. Make sure to insert FOMA card into FOMA terminal before inserting to a PC. Do not remove FOMA card while using FOMA terminal. Verify the FOMA terminal is properly inserted into a PC. Verify that the FOMA terminal is properly recognized by the PC. An incorrect PIN1was improperly entered 3 times in a row. Available functions will be limited. Enter PIN unblocking code to unlock. An incorrect PIN1 code has been entered. Enter the correct PIN1 code again. You can use 0,1,2,3,4,5,6,7,8,9 as a valid PIN1 code. Others are invalid. Valid PIN1 code is from 4 to 8 digit. 100 Appendix/Troubleshooting CON_Guide_E.book 101 Error Messages PIN1PIN PIN/

10 SMS PIN1 FOMA FOMAFOMA To change the PIN1, PIN must be locked. Switch PIN unblocking to PIN blocking. Description An incorrect PIN was imporperly entered 10 times in a row. Available functions will be limited. Please enter the contact unblocking PIN code. You may be out of service or available network.You may encounter problems due to the network error. You are no longer able to use FOMA card that PIN1 unblocking code has been improperly entered10 times in a row. Please contact DOCOMO shop. Communication may fail and the FOMA terminal cannot be properly recognized, if the PC is started up or restarted with the FOMA terminal left inserted in it. In this case, remove and reinsert the FOMA terminal. If communication fails even after the FOMA terminal is inserted again, remove it once, restart the PC, then insert the FOMA terminal into the PC again. When no data transmission has been incurred for a certain period of time. Communication will be resumed when data transmission is incurred, so stay as it is. Appendix/Troubleshooting 101 CON_Guide_E.book 102 Warranty and After-Sales Service Warranty

A written warranty is provided with every FOMA terminal. Make sure that you receive it. Store the warranty in a safe place after you read it and verified that it contains the shop name/date you purchased the product. If the written warranty does not contain the necessary information, contact the shop where you purchased the product. The warranty is valid for a period of one year from the date of purchase.

This product and all accessories are subject to change, in part or whole, for the sake ofimprovement without prior notice. After-Sales Service If Problems Occur

Before requesting service, read the "Troubleshooting section in this manual. If the problem still persists, contact one of the numbers listed in Repairs on the back of this manual. 102 Appendix/Troubleshooting If the Result of Inquiries Indicates that a Repair is Required

Take your FOMA terminal to a service center designated by DOCOMO. Be sure to check the operating hours of the service center. You must present the warranty. In the warranty period

The FOMA terminal will be repaired at no charge subject to the conditions of the warranty.

The warranty must be presented to receive warranty service. The subscriber will be charged for the repair of items not covered in the warranty or repairs of defects resulting from misuse, accident or neglect even during the warranty period.

The subscriber is charged even during the warranty period for the repair of failures caused by the use of devices or consumable items that are not DOCOMO specified.

You will be charged if damage is found on the connector or etc after purchasing product. Repairs may not be possible in the following cases

When DOCOMO Repairs judges that the FOMA terminal is exposed to water. (Ex: the sticker is reacted to water)

Repair is not possible when corrosion due exposure to moisture, condensation or perspiration is detected in a moisture seal reaction or test, or if any of the internal boards are damaged or deformed. Since these conditions are outside the scope of the warranty, any repairs, if at all possible, will be charged. After expiration of the warranty All repairs that are requested are charged. CON_Guide_E.book 103 Replacement parts Basically, replacement parts (parts required to maintain product function) will be kept in stock for at least 4 years after termination of production. Please note that the product may not be repaired even during this period, depending on the malfunctioning parts due to a shortage of those parts. Depending on the nature of the required repairs, it may still be possible to repair your terminal even after this period. Contact Repairs listed on the back of this manual. Updating software Download the modification file of FOMA terminal from download site on the Internet and then update the software. If software update is necessary, you will be informed at the DOCOMO web site with "

Information". Pay attention Note

Do not modify the FOMA terminal, the FOMA card or its accessories.

- Fire, injury or damage may result.

- If the FOMA terminal is modified (part replacement, modification, painting, etc.), it will be repaired only after the modified parts have been restored to the condition at the time of purchase. However, repair may be refused depending on the nature of modification. Using sticker to decorate the FOMA terminal. Exchanging the packing with those other than DOCOMO product.

- Repair of failures or damage caused by modification are charged even during the warranty period.

Do not unplug the FOMA terminal with the computer during software update.

Software update (downloading and rewriting) may take a while. If software update fails, all operations become unavailable. In this case, bring your FOMA terminal to a DOCOMO service center.

Do not remove any inscription stickers attached to the FOMA terminal. The inscription stickers certify that the FOMA terminal satisfies specific technical standards. If stickers are removed intentionally or are reattached in such a way that confirmation of the sticker's contents is impossible, repair or servicing may be refused because confirmation of whether or not the device conforms to relevant technical standards cannot be made. Appendix/Troubleshooting 103 CON_Guide_E.book 104 Power source Power voltage DC5V5%(Supplied from PC) Max Current consumption Max Current consumption while communicating:

Approx. 600mA or below Average Current consumption while communicating:

Approx. 328mA or below Average Current consumption while Standby:

Approx. 41mA or below Depending on the usage, power consumption fluctuates. Form factor USB connection type Dimensions Height: approx. 80mm Width: approx. 34mm Depth: approx. 11.8mm Weight Approx. 35g Main specifications Operation system Windows 2000 Professional Japanese version

(Service Pack 4 or later) Windows XP Home Edition Japanese version

(Service Pack 2 or later) Windows XP Professional Japanese version

(Service Pack 2 or later) Windows Vista 32 bit Japanese version (Service Pack1 or later) Windows Vista 64 bit Japanese version (Service Pack1 or later) Mac OS X 10.4.11 Japanese version Mac OS X 10.5.5 Japanese version Communication Speed Packet Communication Maximum receiving: 7.2MbpsBest effort Maximum sending: 384kbpsBest effort The maximum speed of 7.2Mbps for receiving and 384kbps for sending is theoretical values and does not show the actual ones.The actual communication speed depends on communication environment and network congestion. Out of High-Speed area, the maximum communication speed for receiving and sending is 384kbps Operating environment Temperature535 Humidity45%85%

104 Appendix/Troubleshooting CON_Guide_E.book 105 Export Controls of the Product and Accessories Japan Export Control Regulations (Foreign Exchange and Foreign Trade Law and relevant laws and regulations) and U.S. Reexport Regulations (Export Administration Regulations: EAR) apply to this product and its accessories. If you export or re-export this product or its accessories, please follow the necessary procedures at your own risk and expense. For details on the procedures, contact the Ministry of Economy, Trade and Industry or the U.S. Department of Commerce. European Union Directives Conformance Statement Hereby, LG Electronics, Inc. declares that this product is in compliance with:

The essential requirements and other relevant provisions of Directive 1999/5/EC

All other relevant EU Directives 0168 The above gives an example of a typical Product Approval Number. FCC Regulations Statement This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. if this equipment does cause harmful interference or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help. Change or Modifications that are not expressly approved by the manufacturer could void the user's authority to operate the equipment. Appendix/Troubleshooting 105 CON_Guide_E.book 106 Class B Compliance This device and its accessories comply with part15 of FCC rules. Operation is subject to the following two conditions:

This device & its accessories may not cause harmful interference.

This device & its accessories must accept any interference received, including interference that may cause undesired operation. Body-worn Operation This device has been tested for typical body-worn operations with the distance of 0.19inches (0.5cm) from the user's body. To comply with FCC RF exposure requirements, a minimum separation distance of 0.19inches(0.5cm) must be maintained from the user's body. 106 Appendix/Troubleshooting Consumer Information on SAR (Specific Absorption Rate) THIS DEVICE MEETS THE GOVERNMENT'S REQUIREMENTS FOR EXPOSURE TO RADIO WAVES. Your wireless device is a radio transmitter and receiver. It is designed and manufactured not to exceed the emission limits for exposure to radiofrequency (RF) energy set by the Federal Communications 'Commission of the U.S. Government. These limits are part of comprehensive guidelines and establish permitted levels of RF energy for the general population. The guidelines are based on standards that were developed by independent scientific organizations through periodic and thorough evaluation of scientific studies. The standards include a substantial safety margin designed to assure the safety of all persons, regardless of age and health. The exposure standard for wireless devices employs a unit of measurement known as the Specific Absorption Rate, or SAR. The SAR limit set by the FCC is 1.6W/kg. Tests for SAR are conducted using standard operating positions specified by the FCC with the device transmitting at its highest certified power level, the actual SAR level of the device while operating can be well below the maximum value. This is because the device is designed to operate at multiple power levels so as to use only the power required to reach the network. In general, the closer you are to a wireless base station antenna, the lower the power output. CON_Guide_E.book 107 Before a device is available for sale to the public, it must be tested and certified to the FCC that it does not exceed the limit established by the government-adopted requirement for safe exposure. The tests are performed in positions and locations (e.g., worn on the body) as required by the FCC for each model. The highest SAR value for this device when worn on the body is 1.17W/kg. The FCC has granted an Equipment Authorization for this device with all reported SAR levels evaluated as in compliance with the FCC RF emission guidelines. SAR information on this device is on file with the FCC and can be found under the Display Gant section of http://

www.fcc.gov/ after searching on FCC ID BEJL02A. Additional information about Specific Absorption Rates

(SAR) can be found on the Cellular Telecommunications Industry Association (CTIA) web-site at http://www.wow-com.com. Intellectual Property Rights Copyrights and Rights of Portrait Without permission of the copyright owner you may not duplicate, modify, transmit over public communication lines, etc. any document, image, music, software, or other content owned by a third party that you have used this product to download from an Internet web site, etc., except for private uses such as duplication and indexing that are allowed by copyright law. Appendix/Troubleshooting 107 CON_Guide_E.book 108 Trademarks

TheFOMAmopera UmoperaWORLD WINGand FOMAlogo are trademarks or registered trademarks of NTT DOCOMO, INC.

Free Dial logo mark is a registered trademark of NTT Communications Corporation.

Microsoft, Windows , Windows Vista are US and other countries registered trademarks of Microsoft Corporation.

Windows Vista is the abbreviation of Microsoft Windows Vista Home Basic operating systemMicrosoft Windows Vista Home Premium operating system Microsoft Windows Vista Business operating systemMicrosoft Windows Vista Enterprise operating systemMicrosoft Windows Vista Ultimate operating system.

Windows XP is the abbreviation of Microsoft Windows XP Professional operating system or Microsoft Windows XP Home Edition operating system.

Windows 2000 is the abbreviation of Microsoft Windows 2000 Professional operating system.

OS may be written abbreviated such as Windows Vista, XP, 2000.

AppleApple logoMacMac OSMacintosh are registered trademark of Apple Inc. of US and other countries.

Adobe and Adobe Reader are either registered trademarks or trademarks of Adobe Systems Incorporated in the United States and/or other countries.

Other company names or product names mentioned in this work are the trademarks or registered trademarks of their respective owners. 108 Appendix/Troubleshooting CON_Guide_E.book 109 Index A Available Communications.................76 C Communication Speed ..................... 104 Configuring Network Packet Communication...................76 Connecting FOMA terminal to a PC ..................................................77 E Error Messages................................... 100 F FOMA Card Inserting/Removing ..........................74 Form factor ...........................................104 I Install L-02A Connection Software on Macintosh (including a driver)...90 L-02A Connection Software on Windows (including a driver)......85 T Troubleshooting..................................... 98 U Uninstall L-02A Connection Software

(including a driver)......................... 93 M Main specifications ........................... 104 Mode Indication Lamp .........................73 N Names of Parts and Functions........72 O Operating Environment .................... 104 Operation system............................... 104 P Power source....................................... 104 Purchased Product and Accessories ........................................69 R Removing FOMA terminal...................79 S Setting up ................................................82 Appendix/Troubleshooting 109 CON_Guide_E.book 110 MEMO 110 CON_Guide_E.book 111 MEMO 111 CON_Guide_E.book 112 MEMO 112 CON_Guide_E.book 113 My docomohttp://www.mydocomo.com/

docomo ID docomo ID You can register a confirmation/change of contracts, or request information material at the DOCOMO online. From a PCMy docomohttp://www.mydocomo.com/

(Subscriptions/Procedures)

"docomo ID/Password" is required if you access the site from a PC. If you do not have or remember the "docomo ID/Password", contact the "docomo Information Center" listed on the back of this manual. Some contracts may not be available for using. You may not be able to use online service due to system maintenance, etc. FOMA FOMA Don't forget your FOMA terminal or your manners!

When using the FOMA terminal, be considerate and do not disturb people around you. the following cases, be certain to turn off your PC in which the FOMA terminal is inserted. FOMA FOMA

FOMA FOMA FOMA Where use is prohibited There are some places which FOMA terminal can not be used. Be sure to turn off your PC in which the FOMA terminal is inserted.

Persons with electronic medical equipment are in places other In airplane In hospital than the actual wards. Make sure you have the power switched off even if you are in a lobby or waiting room. While driving Using the FOMA terminal interferes with safe driving and may be dangerous. When in crowded places such as packed trains, where you could be near a person with an implanted cardiac pacemaker or implanteddefibrillator The implanted cardiac pacemaker or implanted defibrillator operation can be adversely affected. When in theaters, movie theaters, museums, and similar venues If you use your FOMA terminal where you are supposed to be quiet, you may disturb those around you.