FCC ID: BEJTL19BNN Telematics

Technical Specification (TL19BNN) 1/10 History Ver. 1.0 Date 2017.12.26 Contents Written by Checked by Approved by Note 2/10 Contents 1. Product Introduction ...................................................................................................... 4 1.1 Block Diagram ...................................................................................................... 4 1.2 Environmental Specifications ............................................................................... 5 1.3 Electrical Specifications ....................................................................................... 5 1.3.1 Absolute Maximum and ESD Ratings ........................................................... 5 1.3.2 Current Consumption .................................................................................... 6 1.4 Mechanical Specifications .................................................................................. 6 1.4.1 Physical Dimensions and Connection Interface ............................................ 6 1.4.2 Mechanical Drawing ...................................................................................... 7 2. RF Specification ............................................................................................................ 8 2.1. LTE Specification ................................................................................................ 8 2.2. WCDMA Specification.................. 9 3/10 1. Product Introuction The TL19BNN are designed for the automotive industry. They support LTE and WCDMA air Interface standards. The TL19BNN are based on the Qualcomm MDM9628 wireless chipsets and support the following bands. Table 1. Supported Band Region US LTE Band B2/B4/B5/B12/

B13/B17/B26 WCDMA B2/B4/B5 1.1 Block Diagram Confidential Figure 1.1. TL19BNN Block diagram 4/10 1.2 Environmental Specifications The environmental specification for operating and storage of the TL19BNN are defined in the the table below. Table 2. Environmental Specifications Parameter Operating Temperature Storage Temperature Humidity Temperature Range

-40 to 85

-40 to +90 95% or less 1.3 Electrical Specifications This section provides details for some of the key electrical specifications of the TL19BNN embedded modules. 1.3.1 Absolute Maximum Rating and ESD Ratings This section defines the Absolute Maximum and Electrostatic Discharge (ESD) Ratings of the TL19BNN embedded modules. Warning: If these parameters are exceeded, even momentarily, damage may occur to the device. Table 3. Absolute Maximum Ratings Parameter

+12.0_VPWR Power Supply Input VIN ESD Ratings Primary, Diversity antenna pads - Contact ESD1) 1) The ESD Simulator configured with 330pF, 2000. Caution: The TL19BNN embedded modules are sensitive to Electrostatic Discharge. ESD countermeasures and handling methods must be used when handling the TL19BNN devices. Voltage on any digital input or output pin VREG_MDME+0.5 Min

-

-

Max 16.0V Units V V kV 10 5/10 1.3.2 Current Consumption Table 4. TL19BNN Current Consumption (TBD) Mode LTE Parameter Max TX Output /Full RB WCDMA Max TX Output /Full RB LTE WCDMA Idle, Registered Idle, Registered Sleep Mode, Average Current WCDMA Sleep Mode, Average Current LTE Typical Max 650 600 600 650 4.0 3.6 4.0 3.6 1.8 2.2 2.2 1.8 Units mA mA mA mA mA mA 1.4 Mechanical Specifications 1.4.1 Physical Dimensions and Connection Interface The TL19BNN embedded modules are a Land Grid Array (LGA) form factor device. The device does not have a System or RF connectors. All electrical and mechanical connections are made via the 387 pad TL19BNN on the underside of the PCB. Table5. TL19BNN Embedded Module Dimensions Parameter Overall Dimension Overall Module Height PCB Thickness Flatness Specification Weight Max 34.35 x 40.35 4.0 1.1 0.1 Nominal 34 x 40 3.8 1.0 TBD Units mm mm mm mm g 6/10 1.4.2 Mechanical Drawing 1.4.2.1 NAD PCB 40mm 34mm 3.8mm

[TOP View_Without shield Can cover] [TOP View_With shield Can cover]

[SIDE View_With shield Can cover]

7/10 2. RF Specification The specifications for the LTE and WCDMA interfaces are defined. TL19BNN is designed to be compliant with the standard shown in the table below. Table6. Standards Compliance Technology LTE WCDMA Standards 3GPP Release 8 3GPP Release 9 2.1 LTE Specification 2.1.1 LTE RX Sensitivity The Receiver Sensitivity of the TL19BNN are specified in the following table. Table7. Conducted RX (Receive) Sensitivity LTE Bands BAND Method (DL CH) BAND 2 Reference sensitivity level(DUAL) BAND 4 Reference sensitivity level(DUAL) BAND 5 Reference sensitivity level(DUAL) BAND 12 Reference sensitivity level(DUAL) BAND 13 Reference sensitivity level(DUAL) BAND 17 Reference sensitivity level(DUAL) BAND 26 Reference sensitivity level(DUAL) Measure BLER of Mid Channel (900) in Band2 Measure BLER of Mid Channel (2175) in Band4 Measure BLER of Mid Channel (2525) in Band5 Measure BLER of Mid Channel (5095) in Band12 Measure BLER of Mid Channel (5230) in Band13 Measure BLER of Mid Channel (5790) in Band17 Measure BLER of Mid Channel (8865) in Band26 Specification sensitivity : -95 BLER : 5%

sensitivity : -97 BLER : 5%

sensitivity : -95 BLER : 5%

sensitivity : -94 BLER : 5%

sensitivity : -94 BLER : 5%

sensitivity : -94 BLER : 5%

sensitivity : -94.5 BLER : 5%

2.2 WCDMA Specification 2.2.1 WCDMA RX Sensitivity 8/10 The Receiver Sensitivity of the TL19BNN are specified in the following table. Table8. Conducted RX (Receive) Sensitivity WCDMA Bands Item Method (DL CH) BAND2 BER(Bit Error Rate) BAND4 BER(Bit Error Rate) BAND5 BER(Bit Error Rate) Measure BER of Middle Channel (CH=9800) in Band2 Measure BER of Middle Channel (CH=1675) in Band4. Measure BER of Middle Channel (CH=4400) in Band5 Specification 0.1% @-106.7dBm 0.1% @-106.7dBm 0.1% @-106.7dBm 9/10 Notice Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the receiver is

-Consult the dealer or an experienced radio/TV technician for help. This device complies with FCC radiation exposure limits set forth for an uncontrolled environment. This device should be installed and operated with minimum distance 20cm between the radiating element of this device and the user. connected. 10/10

FCC ID: BEJTL19BNN SAMPLE LABEL & LOCATION LABELLING REQUIREMENTS The Label shown shall be permanently affixed at a conspicuous location on the device and be readily visible to the user at the time of purchase Label

- The label shown is representative of the label that will appear on the radio when in production. Other information may also be included on this label. Copyright 2018, DT&C Co., Ltd.

LG Electronics USA 1000 Sylvan Avenue, Englewood Cliffs, New Jersey, United States, 07632 Date: April 18, 2018 Timco Engineering, Inc. 849 N.W. State Road 45 P.O. Box 370 Newberry, Florida 32669 USA Kyung-Su Han Director, Standards & Compliance Letter of Authorization We, the undersigned, hereby authorize Harvey Sung of DT&C Co., Ltd. to act on our behalf in all manners relating to application for equipment authorization for FCC ID: BEJTL19BNN including signing of all documents relating to these matters. Any and all acts carried out by Harvey Sung of DT&C Co., Ltd. on our behalf shall have the same affect as acts of our own. This authorization is valid until further written notice from LG Electronics USA I, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). Sincerely,

LG Electronics USA 1000 Sylvan Avenue, Englewood Cliffs, New Jersey, United States, 07632 Date: April 18, 2018 Timco Engineering, Inc. 849 N.W. State Road 45 P.O. Box 370 Newberry, Florida 32669 USA RE: Request of Confidentiality for FCC ID: BEJTL19BNN To Whom It may Concern:

Pursuant to Sections 0.457 and 0.459 of the Commission`s Rules(CFR 47), and Section 552 (b) (4) of the Freedom of Information Act, LG Electronics USA hereby requests confidentiality and treatment of certain information accompanying this application. The materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. We are also hereby request Short-Term Confidentiality for 180 days after the grant as outlined in Public Notice DA 04-1705. This provision will give LG Electronics USA temporary confidentiality of commercially sensitive information prior to product release. The requested permanent and Short-Term Confidential exhibits are listed as follows:

Exhibit Description PERMANENT & SHORT-TERM CONFIDENTIAL LIST PERMANENT SHORT-TERM 1 2 3 4 5 6 7 8 9 Block Diagram Schematics Part Lists Operation Description Tune up Procedure Internal Photos External Photos Test-Setup Photos User Manual The Applicant understands that pursuant to Rule 0.457, disclosure of this application and all accompanying documentations, where applicable, will not be public before the date of the Grant for this application. Sincerely, Kyung-Su Han Director, Standards & Compliance