FCC ID: BEJTL1R22NR Telematics

User Manual

(TL1R22NR, TL1R22NE) FCCID:BEJTL1R22NR 1/6 1. Product Introduction The TL1R22NRare designed for the automotive industry. They support LTE and WCDMA air Interface standards. The TL1R22NR are based on the Qualcomm MDM9250 wireless chipsets and support the following bands. Table 1. Supported Band Band Band B2 B4 B5 B7 B12(B17) B26 B41 TL1R22NR TL1R22NE W, L W, L W, L L L G, W, L W, L G, W, L L L L L G: GSM / W: WCDMA / L: LTE 1.1 Block Diagram Confidential Figure 1.1. TL1R22NR Block diagram 2/6 1.2 Environmental Specifications The environmental specification for operating and storage of the TL1R22NR are defined in the the table below. Table 2. Environmental Specifications Parameter Temperature Range Operating Temperature Storage Temperature Humidity

-40 to 90 (ecall 95)

-40 to +95 95% or less 1.3 Electrical Specifications This section provides details for some of the key electrical specifications of the TL1R22NR embedded modules. 1.3.1 Absolute Maximum Rating and ESD Ratings This section defines the Absolute Maximum and Electrostatic Discharge (ESD) Ratings of the TL1R22NR embedded modules. Warning: If these parameters are exceeded, even momentarily, damage may occur to the device. Table 3. Absolute Maximum Ratings Parameter VBATT VIN ESD Ratings Power Supply Input Voltage on any digital input or output pin Min

Max 18 18 Units V V ESD1) Primary, Diversity antenna pads - Contact 1) The ESD Simulator configured with 330pF, 2000. 10 kV Caution: The TL1R22NR embedded modules are sensitive to Electrostatic Discharge. ESD countermeasures and handling methods must be used when handling the TL1R22NR devices. 3/6 1.3.2 Current Consumption Table 4. TL1R22NR Current Consumption (12.5V) Mode Parameter Typical LTE Max TX Output /Full RB WCDMA Max TX Output /Full RB LTE Idle, Registered WCDMA Idle, Registered LTE Sleep Mode, Average Current WCDMA Sleep Mode, Average Current 450 450 2 2 0.03 0.03 Max 550 550 4 4 Units mA mA mA mA mA mA 4/6 1.4 Mechanical Specifications 1.4.1 Physical Dimensions and Connection Interface Mechanical structure diagram Roof variant Size : 160 x 100 x 18mm Weight : Low variant 285.7g 5/6 2. RF Specification The specifications for the LTE and WCDMA interfaces are defined. TL1R22NR is designed to be compliant with the standard shown in the table below. Table6. Standards Compliance Technology Standards LTE WCDMA GSM 3. Warning Statement FCCWarning 3GPP Release 11 3GPP Release 9 3GPP Release 8 Changesormodificationsnotexpresslyapprovedbythepartyresponsibleforcompliancecouldvoidtheuser'sauthority tooperatetheequipment. Thisdevicecomplieswithpart15oftheFCCRules.Operationissubjecttothefollowingtwoconditions:(1)Thisdevice maynotcauseharmfulinterference,and(2)thisdevicemustacceptanyinterferencereceived,includinginterferencethat maycauseundesiredoperation. NOTE:ThisequipmenthasbeentestedandfoundtocomplywiththelimitsforaClassBdigitaldevice,pursuanttopart15 oftheFCCRules.Theselimitsaredesignedtoprovidereasonableprotectionagainstharmfulinterferenceinaresidential installation.Thisequipmentgeneratesusesandcanradiateradiofrequencyenergyand,ifnotinstalledandusedin accordancewiththeinstructions,maycauseharmfulinterferencetoradiocommunications.However,thereisno guaranteethatinterferencewillnotoccurinaparticularinstallation.Ifthisequipmentdoescauseharmfulinterferenceto radioortelevisionreception,whichcanbedeterminedbyturningtheequipmentoffandon,theuserisencouragedtotry tocorrecttheinterferencebyoneormoreofthefollowingmeasures:

- Reorientorrelocatethereceivingantenna.

- Increasetheseparationbetweentheequipmentandreceiver. Connecttheequipmentintoanoutletonacircuitdifferentfromthattowhichthereceiverisconnected. Consultthedealeroranexperiencedradio/TVtechnicianforhelp. ThisdevicecomplieswithFCCradiationexposurelimitssetforthforanuncontrolledenvironment.Thisdeviceshouldbe installedandoperatedwithminimumdistance20cmbetweentheradiatingelementofthisdeviceandtheuser. 6/6

Model : TL1R22NR, TL1R22NE (Telematics) Label Size : Main Label - 62 X 40 mm Regulation Label - 60 X 34 mm Label Material 1) Paper : Avery MZ1061J1 2) Adhesive : SP4200 3) Liner : G60Em Label Attachment Location on the Product Label Label Model : TL1R22NR, TL1R22NE (Telematics) FCC ID: BEJTL1R22NR FCC ID: BEJTL1R22NR

LG Electronics USA 111 Sylvan Avenue, North Building, Englewood Cliffs, New Jersey, United States, 07632 December 28, 2022 FederalCommunicationsCommission AuthorizationandEvaluationDivision 7435OaklandMillsRoad, Columbia,MD21046 LETTERFORAUTHORIZATION FCC ID: BEJTL1R22NR Towhomitmayconcern:

I,theundersigned,herebyauthorizeSGS KoreaCo.,Ltd. andhereafterreferredtoasSGS Korea,toactonourbehalfinallmannersrelatingtoapplicationforequipmentauthorization, includingsigningofalldocumentsrelatingtothesematters.Anyandallactscarriedoutby SGSKoreaCo., Ltd.onourbehalfshallhavethesameeffectasactsofourown. I, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includesFCCbenefits,pursuanttoSection5301oftheAntiDrugAbuseActof1988,21U.S.C. 853(a). InauthorizingSGSKoreaasouragent,westillrecognizethatweareresponsibleto:

a) complywiththerelevantprovisionsofthecertificationprogram;

b) makeallnecessaryarrangementsfortheconductoftheevaluation,includingprovision forexaminingdocumentationandaccesstoallareas,records(includinginternalaudit reports) and personnel for the purposes of evaluation (e.g. testing, inspection, assessment,surveillance,reassessment)andresolutionofcomplaints;

c) makeclaimsregardingcertificationonlyinrespectofthescopeforwhichcertification hasbeengranted;

d) do not use our product certification in such a manner as to bring the Certification Divisionintodisreputeandnotmakeanystatementregardingourproductcertification whichtheCertificationDivisionmayconsidermisleadingorunauthorized;

e) upon suspension or cancellation of certification, discontinue use of all advertising matter that contains any referencethereto and returnanycertification documents as requiredbytheCertificationDivision;

f) usecertificationonlytoindicatetheproductsarecertifiedasbeinginconformitywith specifiedstandards;

g) endeavor to ensure that no certificate or report nor any part thereof is used in a misleadingmanner;

h) ensurethatanyreferencetoourproductcertificationincommunicationmediasuchas documents, brochures or advertising, complies with the requirements of the CertificationDivision;

LG Electronics USA 111 Sylvan Avenue, North Building, Englewood Cliffs, New Jersey, United States, 07632 i) j) keep a record of all complaints made known to the us relating to the products compliance with requirements of the relevant standard and to make these records availabletotheCertificationDivisionwhenrequested;

takeappropriateactionwithrespecttosuchcomplaintsandanydeficienciesfoundin productsorservicesthataffectcompliancewiththerequirementsforcertification;

k) documenttheactionstaken. Thisauthorizationisvaliduntilfurtherwrittennoticefromtheapplicant. SincerelyYours Mr. Sungsoo Kim Director, Regulatory & Environmental Affairs LG Electronics USA, Inc.

SGS North America Inc. 620 Old Peachtree Road SUITE 100 Suwanee, Georgia 30024 United States Applicant Declaration Applicant Legal Business Name LG Electronics USA Address Grantee Code FCC ID 111 Sylvan Ave, North Building, Englewood Cliffs, NJ 07632 United States BEJ BEJTL1R22NR Authorized Contact Name Sungsoo Kim Contact Email Contact Phone Sungsoo.kim@lge.com 201-816-2003 I, the undersigned, certify that I am an authorized signatory for the Applicant and therefore declare;

a) b) c) d) e) in accordance with 47CFR2.911(d), all of the statements herein and the exhibits attached hereto are true and correct to the best of my knowledge and belief. in accepting a Grant of Equipment Authorization issued by a TCB, under the authority of the FCC, as a result of the representations made in this application, the Applicant is responsible for:

labeling the equipment with the exact FCC ID as specified in this application,

(1)

(2) compliance statement labeling pursuant to the applicable rules,

(3) compliance of the equipment with the applicable technical rules, if the Applicant is not the actual manufacturer of the equipment, appropriate arrangements have been made with the manufacturer to ensure that production units of this equipment will continue to comply with the FCCs technical requirements. in accordance with 47 CFR 2.909 and KDB394321, the Applicant has read, understood and agrees to accept that they are the responsible party and agree to abide by their responsibilities as specified under 47 CFR 2.909 and KDB394321. in accordance with ISO17065, FCC KDB641163, FCC KDB610077, KDB394321 and RSP-100, the Applicant has read, understood, accepts and agrees to abide by the post market surveillance requirements.

(1)

(2)

(3) the Applicant understands, accepts and agrees that a sample may be requested for surveillance testing. the Applicant shall make provisions to always have a production sample available upon request by SGS, FCC and/or ISED. the Applicant shall, upon request by SGS, at the Applicants expense, provide a production sample of the requested product to SGS, FCC and/or ISED as instructed. The sample shall include all support devices, cables, software, accessories or other hardware or software required for evaluation, review, certification and audit surveillance of products certified by SGS. f) neither the Applicant nor any party to the application is subject to a denial of Federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862 because of a conviction for possession or distribution of a controlled substance. See 47CFR 1.2002(b) for the definition of a party for these purposes. g) the Applicant has read, understood, accepts and agrees to abide by the SGS North America, Inc.(TCB) terms and conditions. Link to CFRs: https://www.fcc.gov/wireless/bureau-divisions/technologies-systems-and-innovation-division/rules-regulations-title-47 Link to KDBs: https://apps.fcc.gov/oetcf/kdb/index.cfm Link to RSP-100: https://www.ic.gc.ca/eic/site/smt-gst.nsf/eng/sf01130.html Applicant Signature:

Date: December 28, 2022 Print Name:

Title:

*NOTE: This declaration cannot be signed by an Agent, it shall be signed by an authorized person listed in the FCC database Sungsoo Kim Director, Regulatory and Environmental Affairs Applicant Declaration Rev:0.0

LG Electronics USA 111 Sylvan Avenue, North Building, Englewood Cliffs, New Jersey, United States, 07632 December 28, 2022 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road, Columbia, MD 21046 REQUEST FOR CONFIDENTIALITY FCC ID: BEJTL1R22NR Pursuant to Sections 0.457 and 0.459 of the Commissions Rules (CFR 47), and Section 552 (b) (4) of the Freedom of Information Act, LG Electronics USA hereby requests confidentiality and treatment of certain information accompanying this application. The materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. We are also hereby request Short-Term Confidentiality for 180 days after the grant as outlined in Public Notice DA 04-1705. This provision will give LG Electronics USA temporary confidentiality of commercially sensitive information prior to product release. The requested Permanent and Temporary Confidential exhibits are listed as follows:

Long-Term CONFIDENTIAL LIST Short-Term 1 2 3 4 5 6 7 8 9 10 External Photos Internal Photos Test-Setup Photos User Manual Operational Description Block Diagram Schematics PCB Layout Part List Tune-Up Procedure The Applicant understands that pursuant to Rule 0.457, disclosure of this application and all accompanying documentations, where applicable, will not be made public before the date of the Grant for this application. Sincerely Yours Sungsoo Kim Director, NA Regulatory & Environmental Affairs LG Electronics USA, Inc.

DeclarationofEquivalence We,LGElectronicsInc.,asmanufactureroffollowingproductherebydeclareequalityoffollowingdevices. Thosemodelsaretechnicallyidentical,buttheonlydifferenceiscellularportion. ModelName Remark TL1R22NR TL1R22NE BasicModel MarketinEU Description TheModelsareTL1R22NRandTL1R22NEhavefollowingdifferences.

-CommonPCBdesignbutthecomponentPoporde-poped Models TL1R22NR TL1R22NE Remark FullyMountedModuleonhardware. Band21duplexer,PAareremoved

*DifferencebetweentwomodelsdoesnotaffectbandsthatcanbeusedintheUS.

-SupportedCellularBand MODEL GSM WCDMA LTE TL1R22NR GSM850,PCS1900 B2,B4,B5 B2,B4,B5,B7,B12,B17,B26,B41 TL1R22NE N/A B2,B4,B5 B2,B4,B5,B7,B12,B17

*OperatingbandsaredifferentbySoftware. We,theundersigned,herebydeclarethatthemodelsareidenticalinbothdesignandimplementation. December14,2022 Sungsoo Kim Director, NA Regulatory & Environmental Affairs LG Electronics USA, Inc.