FCC ID: BEJTTAG11NE Telematics

LG Electronics Inc. 1 17-8-8 Technical Description Descriptive Information The RF platform of GEN11 supports highly integrated LTE/UMTS/GSM-transceiver, with all necessary features to enable multi mode, multi band car telematics applications. It incorporates a fully integrated dual mode receiver, multi band TX outputs, TCVCXO control, a measurement interface, Qualcomm(Transceiver / Modem) compliant high speed data and control interface, a multi mode timer unit and all necessary front end signals for the complete RF Engine control. Overall the GEN11 directly supports RF engines with up to GSM bands, WCDMA bands and LTE bands. 1. RF Transceiver (WTR3925) Multimode operation (See modem IC documents for specific capabilities)

- 3GPP GSM, GPRS, and EDGE (WTR3925/WTR3905 only)

-

-

-

3GPP WCDMA Rel 99, HSDPA, HSUPA, HSPA+

3GPP LTE FDD and TDD, with carrier aggregation (WTR3925 only) TD-SCDMA LTE carrier aggregation WTR3925 only Downlink inter-band (20 MHz and 20 MHz) Downlink intra-band Non-contiguous 20 MHz + 20 MHz Contiguous, 40 MHz for certain bands

-

-

-

-

1) RF Transmitter Part Transmit signal paths

-

-

Ten single-ended Tx outputs (4 LB, 4 MHB, and 2 HMLB) WTR3925/WTR3905 only Six single-ended Tx outputs (3 LB, 2 MHB, and 1 HMLB) WTR3900 only

- One 4-line analog baseband interface from modem IC (differential I and Q)

- One baseband-to-RF quadrature upconverter supports all Tx bands

- RF AGC amplifiers and filters LO generation and distribution

-

Single Tx PLL; divider and distribution circuits to support all Tx bands Tx bandpass filters

-

Eliminated for most modes/bands supported 1/12 LG Electronics Inc. 2 17-8-8 2) RF Receiver Part Primary receiver paths

- 14 single-ended PRx inputs (4 LB, 5 MB, 1 MLB, 4 HB)

- Three PRx/CA1 RF-to-baseband quadrature downconverters (LB, MB, HB)

- Three PRx/CA2 RF-to-baseband quadrature downconverters (LB, MB, HB)

- Baseband filtering and amplifiers

- Two single-ended I and Q interfaces to modem IC (PRx/CA1, PRx/CA2) Diversity receiver paths

-

-

-

14 single-ended DRx inputs (4 LB, 5 MB, 1 MLB, 4 HB) Three DRx/CA1 RF-to-baseband quadrature downconverters (LB, MB, HB) Three DRx/CA2 RF-to-baseband quadrature downconverters (LB, MB, HB)

- Baseband filtering and amplifiers

-

Two single-ended I and Q interfaces to modem IC (DRx/CA1, DRx/CA2) 2. RF Transceiver (WTR4905) Multimode operation (See modem IC documents for specific capabilities)

- 3GPP GSM, GPRS, and EDGE

- 3GPP WCDMA Rel 99, HSDPA, HSUPA, HSPA+

- 3GPP LTE FDD and TDD Advanced RF techniques

- Mobile Rx diversity (but not SHDR due to single Rx VCO)

-

Simultaneous GNSS 1) RF Transmitter Part Transmit signal paths

- Wideband single-ended Tx outputs

- WTR4905 = 5

-

4-line analog baseband interface from modem IC (differential I & Q)

- One baseband-to-RF quadrature upconverter supports all Tx bands RF AGC amplifiers LO generation and distribution

-

Tx PLL; divider and distribution circuits to support all Tx bands External Tx bandpass filters

-

Eliminated for most modes/bands supported 2) RF Receiver Part Primary receiver paths

-

Single-ended PRx inputs WTR4905 = 8 (3 LB, 3 MB, 2 HB) 2/12 LG Electronics Inc. 3 17-8-8

- PRx RF-to-baseband quadrature downconverters Two SAWless: LB for GSM, MB/HB for GSM and TD-SCDMA For all other WAN:

WTR4905 = 3 (LB, MB, and HB)

- Baseband filtering and amplifiers

-

2-line analog baseband interface to modem IC (single-ended I & Q)

- Diversity receiver paths

-

Single-ended DRx inputs WTR4905 = 7 (3 LB, 2 MB, 2 HB)

- DRx RF-to-baseband quadrature downconverters WTR4905 = 3 (LB, MB, and HB)

- Baseband filtering and amplifiers 2-line analog baseband interface to modem IC (single-ended I & Q)

-

3. Modem Part (MDM9615) The MDM9x40 is the latest-generation Qualcomm Technologies, Inc. (QTI) MDM device, which further expands mass-market chipset capabilities by making 3G and 4G high-speed data services accessible to more consumers in developed and developing countries. An MDM device is similar to a QTI MSM device, but without multimedia logic. The MDM9x40 chipset supports high-speed data capabilities over a wide range of air interface standards. The MDM9x40 device is fabricated using the advanced 20 nm SoC CMOS process, and is available in the 8.6 9.8 0.82 mm, 527-pin pico-scale package (527 PSP). It includes many ground pins for improved electrical grounding, mechanical strength, and thermal continuity. 4. Power Management Part (PMD9645) The PMD9645 device integrates all the wireless products power management, general housekeeping, and user interface support functions into a single mixed-signal IC. Its versatile design is suitable for any multimode, multiband product. The PMD9645 mixed-signal BiCMOS device is available in the 103-pin wafer-level nanoscale package (103 WLNSP) that includes ground pins for improved electrical ground, mechanical stability, and thermal continuity.

-

Input power management

- Output voltage regulation

- General housekeeping

- User interfaces

-

IC interfaces 3/12 LG Electronics Inc. 4 17-8-8 5. Clocks The PMIC includes several clock circuits whose outputs are used for general housekeeping functions, and elsewhere within the handset system. These circuits include a 19.2 MHz XO with multiple controllers and buffers, an MP3 clock output, an RC oscillator, and sleep-clock outputs. Performance specifications for these functions are presented in the following subsections.

-

19.2MHz : An external crystal is supplemented by on-chip circuits to generate the desired 19.2 MHz reference signal. Using an external thermistor network, the on-chip ADC, and advanced temperature compensation software, the PMIC eliminates the large and expensive VCTCXO module required by previous-generation chipsets. The XO circuits initialize and maintain valid pulse waveforms, and measure time intervals for higher-level handset functions. Multiple controllers manage the XO warmup and signal buffering, and generate the desired clock outputs. 4/12 LG Electronics Inc. 5 17-8-8 Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. RF Exposure Statement The antenna(s) must be installed such that a minimum separation distance of at least 20 cm is maintained between the radiator (antenna) and all persons at all times. This device must not be co-located or operating in conjunction with any other antenna or transmitter. The highest permitted antenna gains including cable loss for use with this device are:

GSM 850 GSM 1900 WCDMA 2 WCDMA 4 WCDMA 5 LTE 2 LTE 4 LTE 5 LTE 12 LTE 13

-6.15 dBi

-7.09 dBi

-7.09 dBi

-8.05 dBi

-6.15 dBi

-7.09 dBi

-8.05 dBi

-6.15 dBi

-6.29 dBi

-6.46 dBi 5/12 LG Electronics Inc. 6 17-8-8 Manual Information To the End User This device complies with part 15 of the FCC rules Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. IC Warning This device complies with Industry Canada licence-exempt RSS standard(s)."

Operation is subject to the following conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes : (1) l'appareil ne doit pas provoquer de brouillage, et (2) l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. 6/12

LABEL DRAWING FCC ID: BEJTTAG11NE IC: 2703H-TTAG11NE TOP SIDE OF EUT MODEL: TTA19ANEBN FCC ID: BEJTTAG11NE IC: 2703HTTAG11NE MODEL: TTA19ANENN FCC ID: BEJTTAG11NE IC: 2703HTTAG11NE LABEL

LETTER OF AUTHORIZATION FCC ID: BEJTTAG11NE 18 August 2020 I, the undersigned, hereby authorize Technical Manager Jungmin Yang and Dongmin Kim of SGS Korea Co., Ltd. and hereafter referred to as SGS Korea, to act on our behalf in all manners relating to application for equipment authorization, including signing of all documents relating to these matters. Any and all acts carried out by Technical Manager Jungmin Yang and Dongmin Kim of SGS Korea Co., Ltd. on our behalf shall have the same effect as acts of our own. I, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). In authorizing SGS Korea as our agent, we still recognize that we are responsible to:

a) comply with the relevant provisions of the certification program;

b) make all necessary arrangements for the conduct of the evaluation, including provision for examining documentation and access to all areas, records (including internal audit reports) and personnel for the purposes of evaluation (e.g. testing, inspection, assessment, surveillance, reassessment) and resolution of complaints;

c) make claims regarding certification only in respect of the scope for which certification has been granted;

d) do not use our product certification in such a manner as to bring the Certification Division into disrepute and not make any statement regarding our product certification which the Certification Division may consider misleading or unauthorized;

e) upon suspension or cancellation of certification, discontinue use of all advertising matter that contains any reference thereto and return any certification documents as required by the Certification Division;

f) use certification only to indicate the products are certified as being in conformity with specified standards;

g) endeavor to ensure that no certificate or report nor any part thereof is used in a misleading manner;

h) ensure that any reference to our product certification in communication media such as documents, brochures or advertising, complies with the requirements of the Certification Division;

i) j) keep a record of all complaints made known to the us relating to the products compliance with requirements of the relevant standard and to make these records available to the Certification Division when requested;

take appropriate action with respect to such complaints and any deficiencies found in products or services that affect compliance with the requirements for certification; k) document the actions taken. This authorization is valid until further written notice from the applicant. Kyung-Su Han Director, NA Regulatory & Environmental LG Electronics USA

LETTER OF REQUEST PERMISSIVE CHANGE 19 August 2020 We, as a manufacturer of following equipment, hereby submit Class 2/3 Permissive Change application for the FCC and the ISED to change components in the filings. MODEL GEN11NAN FCC FCC ID BEJTTAG11NE 2703H-TTAG11NE 11 November 2017 Original Grant Date 11 November 2017 ISED Certification Number Original Grant Date Equipment Class PCS Licensed Transmitter HVIN/ PMN C2PC Grant Date HVIN/ PMN TTA19ANEBN TTA19ANENN 06 June 2018 TTA20ANEBN TTA20ANENN TTA20BNEBN TTA20BNENN A. Change Note against the FCC / ISED C2PC grants issued in 11/27/2017 The single modular [BEJGEN11NAN/2703H-GEN11NAN] in Host equipment get C2PC approval on 17 August 2020. 1. C2PC on 26 May 2020 a. Added Antenna Information in the grant b. Power Reduction [GSM850, GSM1900]

c. Modified tune up by modified target & tolerance d. Modified EIRP & ERP e. Modified MPE by antenna information, modified target & tolerance, and power reduction 2. C2PC on 17 August 2020 a. FEM change [B4, B5 Duplexer]

b. RF Filter change c. Removing or Changing some of components which are not related to RF part, are related to Digital part B. Test Requirements When the single modular was performed on C2PC test, the jig board was same as main PCB of BEJTTAG11NE. The only difference of test configuration between BEJTTAG11NE and BEJGEN11NAN is BEJTTAG11NE has enclosure covering main PCB and plug-in type module (BEJGEN11NAN) Therefore, we performed Radiated Spurious for GSM850 and LTE Band4 which were worst bands in GEN11NAN. The result is almost same as BEJGEN11NAN data. The purpose of C2PC that concluded on 27 November 2017 had modification in single modular BEJGEN11NAN and those modification are applied on the new host equipment too. Therefore, We confirmed that Host equipment BEJTTAG11NE contains a single modular BEJGEN11NAN without any modification. Declaration Based on the statement above, we hereby request permissive change for both FCC and ISED certification. Approved and signed by Company Name : LG Electronics, Inc. Name : Seunggu,.Kang Tel :+ 82-2-6950-5220 E-Mail : seunggu.kang@lge.com Seoul, Korea / 19 August 2020

(Place, date of issue)

(Signature / stamp) Seunggu, Kang / MANAGER

Pursuant to Sections 0.457 and 0.459 of the Commissions Rules (CFR 47), and Section 552 (b) (4) of the Freedom of Information Act, LG Electronics USA hereby requests confidentiality and treatment of certain information accompanying this application. The materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. We are also hereby request Short-Term Confidentiality for 180 days after the grant as outlined in Public Notice DA 04-1705. This provision will give LG Electronics USA temporary confidentiality of commercially sensitive information prior to product release. The requested Permanent and Temporary Confidential exhibits are listed as follows. The Applicant understands that pursuant to Rule 0.457, disclosure of this application and all accompanying documentations, where applicable, will not be made public before the date of the Grant for this application. REQUEST FOR CONFIDENTIALITY FCC ID: BEJTTAG11NE 18 August 2020 Confidential List Long-Term Short-Term Block Diagram Part list Schematics External Photos Internal Photos Test-Setup Photos Kyung-Su Han Director, NA Regulatory & Environmental LG Electronics USA

LG Electronics USA 1000 Sylvan Avenue Englewood Cliffs, New Jersey, United States 23 November 2017 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road, Columbia, MD 21046 REQUEST FOR CONFIDENTIALITY FCC ID: BEJTTAG11NE Pursuant to Sections 0.457 and 0.459 of the Commissions Rules (CFR 47), and Section 552

(b) (4) of the Freedom of Information Act, LG Electronics USA hereby requests confidentiality and treatment of certain information accompanying this application. The materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. We are also hereby request Short-Term Confidentiality for 180 days after the grant as outlined in Public Notice DA 04-1705. This provision will give LG Electronics USA temporary confidentiality of commercially sensitive information prior to product release. The requested Permanent and Temporary Confidential exhibits are listed as follows:

Confidential List Long-Term Short-Term Block Diagram Operational Description , Tune-up Procedure Schematics External Photos Internal Photos Test-Setup Photos User Manual The Applicant understands that pursuant to Rule 0.457, disclosure of this application and all accompanying documentations, where applicable, will not be made public before the date of the Grant for this application. Sincerely, Kyungsu Han Director Standards & Compliance LG Electronics USA

LG Electronics USA 1000 Sylvan Avenue Englewood Cliffs, New Jersey, United States 8 September 2017 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road, Columbia, MD 21046 LETTER FOR AUTHORIZATION I, the undersigned, hereby authorize Lab Manager Hyunchae You of SGS Korea Co., Ltd. and hereafter referred to as SGS Korea, to act on our behalf in all manners relating to application for equipment authorization, including signing of all documents relating to these matters. Any and all acts carried out by Lab Manager Hyunchae You of SGS Korea Co., Ltd. on our behalf shall have the same effect as acts of our own. I, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the AntiDrug Abuse Act of 1988, 21 U.S.C. 853(a). In authorizing SGS Korea as our agent, we still recognize that we are responsible to:

a) comply with the relevant provisions of the certification program;

b) make all necessary arrangements for the conduct of the evaluation, including provision for examining documentation and access to all areas, records (including internal audit reports) and personnel for the purposes of evaluation (e.g. testing, inspection, assessment, surveillance, reassessment) and resolution of complaints;

c) make claims regarding certification only in respect of the scope for which certification has been granted;

d) do not use our product certification in such a manner as to bring the Certification Division into disrepute and not make any statement regarding our product certification which the Certification Division may consider misleading or unauthorized;

e) upon suspension or cancellation of certification, discontinue use of all advertising matter that contains any reference thereto and return any certification documents as required by the Certification Division;

f) use certification only to indicate the products are certified as being in conformity g) endeavor to ensure that no certificate or report nor any part thereof is used in a with specified standards;

misleading manner;

LG Electronics USA 1000 Sylvan Avenue Englewood Cliffs, New Jersey, United States h) ensure that any reference to our product certification in communication media such as documents, brochures or advertising, complies with the requirements of the Certification Division;

i) keep a record of all complaints made known to the us relating to the products compliance with requirements of the relevant standard and to make these records available to the Certification Sincerely, Kyungsu Han Director Standards & Compliance LG Electronics USA

LG Electronics USA 1000SylvanAvenueEnglewoodCliffs,NewJersey,UnitedStates 23November2017 FederalCommunicationsCommission AuthorizationandEvaluationDivision 7435OaklandMillsRoad, Columbia,MD21046 LETTER OF DECLARATION FCC ID: BEJTTAG11NE We,LGElectronicsInc.asmanufacturerofproductmentionedherebydeclarefollowingitemtoreuse testreportfromBEJGEN11NANtohaveseparateownFCCIDofhostequipmentrefertoKDB996369. NEW HOST FCC ID:

BEJTTAG11NE CERTIFIED MODULAR:

BEJGEN11NAN(SingleModulargrant,14Sep2017) REPORT NUMBER DATE REMARK F690501/RF-RTL011621 17Jul2017 InitialLTEtestreportofmodular F690501/RF-RTL011622 17Jul2017 InitialWCDMAtestreportofmodular F690501/RF-RTL011623 17Jul2017 InitialGSMtestreportofmodular F690501/RF-RTL011771-2 11Sep2017 RadiatedtestreportforC2PC F690501/RF-RTL011772 11Sep2017 MPEtestreportforC2PC 1. HostequipmentBEJTTAG11NEcontainsasinglemodularBEJGEN11NAN(C2PCgrantissuedon 14September2017)withoutanymodification. 2. ThepurposeofC2PCthatconcludedon14September2017hadfollowingmodificationand thosemodificationareappliedonthenewhostequipmenttoo. A. LTEband17hasbeendisabledbysoftware. B. USBdetectblockhasbeenremoved. C. Originalgrantwasissuedbasedontestreportwithenclosure.itwasnotconsideredas standaloneconfigurationsograntwasissuedaslimitedmodular.C2PCwasdonetochange thelimitedmodulargranttosinglemodulargrantbydoingradiatedtestingagainwithout enclosure. D. TheUSBdetectblockwasremovedsotwoproductswereslightlydifferentbutthisdevice complies standards both with enclosure and without enclosure. Therefore, having the enclosuredoesnotdegradeperformance,conformityorcompliance LG Electronics USA 1000SylvanAvenueEnglewoodCliffs,NewJersey,UnitedStates 3. The only difference of test configuration between BEJTTAG11NE and BEJGEN11NAN is BEJTTAG11NEhasenclosurecoveringmainPCBandplug-intypemodule(BEJGEN11NAN). 4. ThemainPCBofBEJTTAG11NEisthesameboardthatweusedforthemodularcertificationof BEJGEN11NAN. 5. Nomodificationismadetothetransmitterandjigboard. 6. Thehostequipmenthassameexternalantennathatweusedforthemodularcertification. 7. The host equipment will solely be used in vehicle by vehicle manufacturer. Device will be installedinsidevehicleanduserswillhavemorethan20cmdistancefromtheequipment. 8. ThereisnoadditionaltransmitterintheBEJTTAG11NEsothereisnosimultaneoustransmission toconsider. Basedonthestatementabove,weherebydeclareoriginaltestreportexhibitcanbereused. Sincerely, KyungsuHan Director Standards&Compliance LGElectronicsUSA