12+
Rechargeable 2.4GHz STUNT DRONE Rechargeable 2.4GHz STUNT DRONE Rechargeable 2.4GHz STUNT DRONE GETTING TO KNOW YOUR DRONE INTRODUCTION SPECIFICATIONS READ ALL WARNINGS AND PRECAUTIONS BEFORE USE Congratulations on your purchase of Drone Battery: 350 mAh Li-po A PLEASE READ ALL WARNINGS AND INSTRUCTIONS me Ee ae i Stunt Remote Controller Battery: 6 x 1.5V AA SAFETY WARNINGS:
rone. Get rea Oo Soar to new . P 7 PRIOR TO USE. KEEP THIS DOCUMENT AS IT CONTAINS heights. Master i. art of drone flyin Charging Time: Approximately 60 minutes . Not recommended for children under 12 years of age. As with all electrical products, precaution IMPORTANT INFORMATION ABOUT YOUR DRONE. ana. stunting with remote.control g Maximum Recommended Altitude 115 ft. should be observed during handling and use to reduce the risk of electrical shock. maneuverability. This lightweight s Adult supervision is required at all times. stunting drone will provide hours of . Before each use, an adult should review the product and battery to determine that no damage or 1. CHARGING fun. hazards exist.
+ Drone must be charged before each use (cable included) DO NOT TOUCH SPINNING PROPELLERS.
+ Indicator light will turn off once fully charged . * F A si es
- Install batteries in remote Do not allow anything to intentionally make contact in any way with spinning propellers. 2. PAIRING + Prevent contact with spinning blades by turning off remote prior to handling drone. Before each flight pair the remote with the drone: TABLE OF CONTENTS + Use caution and pay attention to your surroundings while operating drone. 1. Turn your drone on and place on a flat, level surface si Do not fly drone into animals, people, or inanimate objects. 2. Turn on the remote on and move the left joystick down, then up, then down again . Keep drone away from power lines, buildings, trees, public areas, and any other potentially 3. The beep will indicate successful pairing General Warnings Page 1 hazardous areas. 3. DIRECTIONAL LIGHTS - Do not operate in rain, heavy wind, and or any type of severe weather. White lights indicate the front of the drone Contents and Remote Battery Installation Page 2 . Do:nat land drone on'wet: surfaces.
+ Red lights indicate the back of the drone . a ais .
+ Not applicable in auto-orientation mode Charging LiPo and Blade Guard Installation Page 3 Never:touch'or. allow cthers:to:touch:drone.while:ttis tlying. 4. REMOTE CONTROL OVERVIEW Renate Overview Page 4 : Always turn drone off when it is not in use. Practice flying your drone below 10 feet and at low speeds until comfortable with all . Always fly drone in large open areas. controls to avoid unncessary damage or injury Operating Drone Page 5 < Never fly drones above or near people, sudden changes in wind or other conditions could lead to
* Left joystick: unexpected crashes.
+ Up/Down controls elevation Modes Page 6 . |
+ Left/Right controls spin 9 Always use caution when flying drone vehicles, obey relevant laws, respect the privacy and
+ Right joystick: controls flight direction Replacing Propellers Page 7 property rights of others.
+ Direction Trim: use to eliminate drift . The drone shall never be modified or used for anything except its intended purpose. To cut power to drone, move left joystick to down position Tips and FCC Warning Page 8 INFORMATION IS AVAILABLE AT CUSTOMER SERVICE L MSCUSTOMERCARE.COM
(800) 374-2744 Before calling please locate the 10-digit code printed on the back of your remote PLEASE RECYCLE OR
& o PROPERLY RECYCLING rea MED OMe MPa) Rec R oe ADULT ASSEMBLY REQUIRED. Page i Page 1 Rechargeable 2.4GHz STUNT DRONE Rechargeable 2.4GHz STUNT DRONE Rechargeable 2.4GHz STUNT DRONE Light indicates Throttle Joystick remote is on Forward/
Backwards Adjustment: Slide up to adjust forward and slide down to adjust backwards CONTENTS CHARGING BATTERY Note: The Battery Charger will light up It yf CH) ee when it is charging the battery and turn 1 Increases or decreases
+ + + off when the battery is fully charged. drone elevation Charge time is approximately 60 minutes. i ON/OFF
< Use L/R arrows for spin Connect the Battery R Remote Switch Charger to the Drone
+ + + Turn off the drone before charging. 5 CI _ CI _ CI _ Connect the Battery Charger to the charge port on the Drone. Insert the connector into a powersource Multi Direction Joystick
] REMOTE BATTERY INFORMATION Stunt Drone Connect connector to 1. Slide open battery compartment. power source. 2. Install 6 AA batteries as shown in diagram shown above. 3. Replace and close battery compartment. r A\LITHIUM-POLYMER BATTERY WARNING There is a risk of fire and personal injury if Li-Po battery is punctured, damaged or misused. z ri @ Ss
+ Never expose battery to extreme temperatures Auto Orientation er ZEraN ee Side to Side or moisture. ON/OFF Z Adjustment:
+ Do not subject battery to strong impacts. Auto Landing Slide left to
. Se battery away from flammable INSTALLING BLADE GUARDS ON/OFF adjust to the materials. , . : i
* Only use manufacturer specified batter(ies), * Click blade guards in place per diagrams below. left and slide Drone Controller charger(s), and/or adapters, if applicable, + Use provided screws and a small screwdriver to secure the blade gaurds before use. right to specified by the manufacturer. DRONE CONTROL MODULE adjust to the
+ Battery is not serviceable. Seance right
+ Let battery cool to room temperature before charging. BEFORE INSTALLATION: AFTER INSTALLATION:
+ While charging, never leave battery unattended.
+ Recycle or dispose of battery according to federal, state and local laws. KEEP THIS INSTRUCTION MANUAL FOR REFERENCE, ) ir BATTERY WARNING
+ Do not mix old and new batteries. reat batteries unig the corect poly Do not shor-oret the supply teminal Spin Adjustment:
+ Only use manufacturer specified batter(ies), charger(s), and/or adapters, if Slide left to spin Replacement applicable, specified by the manufacturer. Connector Pr op ellors + Always use, replace, and recharge (if applicable) batteries under adult supervision. drone counterclockwise KEEP THE PACKAGE FOR REFERENCE AS IT CONTAINS IMPORTANT INFORMATION . X and slide right to spin drone Page 2 Page 3 clockwise re Rechargeable 2.4GHz STUNT DRONE Rechargeable 2.4GHz STUNT DRONE Rechargeable 2.4GHz STUNT DRONE OPERATING DRONE Step 4 - Lift Off MODES REPLACING PROPELLERS 7 . 1. Slowly and carefully bring the throttle up. rapid d 4) Ga aaa Propellers will begin to spin and drone will begin Auto Landing Button 1. Follow diagram to the right. to elevate. You can compensate for some of the + Make sure you have achieved level, balanced flight, where the drone is neither climbing nor 2. Make sure you installed the correct blade. Each blade has a number written on it. 2. Install remote batteries, page 2 a ae : . : 2 3. Make'sur:thatdroriearid remota drones drifting by using the Multi Directional descending.This mode allows you to safely and slowly land your drone without having to control the Match the blades with the corresponding number on the drone.
: Button or by following step 5. You may need to speed. It is done for you automatically. are powered off 4. Charge batteries, page 3. practice this step several times before successfully getting drone into the air. The ideal auto landing height is 25-30 ft. NOTE: Blade 1 turns counter clockwise and Blade 2 turns clockwise Press the Auto Land Button to trigger auto land. Remote will beep continuously until drone lands To steer the drone during landing, use the right control until drone has reached the ground. Press the Press the Auto Land Button again to exit auto landing mode. Step 2 - Choosing a location
. ony is designed to be flown indoors Pe oeire ee begins to drift while NOTE: Please make sure the throttle joystick is on down position before exit auto landing mode
+ Always make sure you have take off or during flight , a enough space to fly drone + Drone drifts backwards: Slide the Auto Orientation Button ak ; A
- Always follow warnings, page 1 Forward/Backwards Adjustment up + Auto Orientation default setting is off. To enter this mode press Auto Orientation button. Remote
+ Drone drifts forwards: Slide the will beep twice. : . a Step 3 - Starting Drone Forward/Backwards Adjustment down + After drone success paired, the 2 white LED lights toward orientation will be the original forward 1. Making sure your remote is off, slide + Drone drifts left: Slide the Side to Side orientation, when drone is in auto orientation mode, whatever the drone spin, the forward orientation drone switch to ON. Drone lights will Adjustment to the right. will Be'previous original forward orientation.
- Drone drifts right: Slide the Side to Side + Remote will beep every 6s to indicate the drone is in Auto Orientation mode. begin to flicker Pn 1
+ To exit mode, press the button. Remote will sound 1 long beep indicating that it has exited Auto 2. Choose a flat even surface and Adjustment to the left. Ori . di follow the diagram + Drone spins clockwise (viewing drone from rientation mode. 3. Turn remote on. Bring the Throttle all top): Slide the Spin Adjustment to the left the way up then bring it all the way + Drone spins counter-clockwise (viewing Stunt Button ; ;
down. Remote will beep and drone drone from top): Slide the Spin Once you are comfortable flying the drone, use the Stunt Button to perform acrobatic stunts. lights will flicker rapidly then turn on Adjustment to the right. 1. Hover the drone to at least above 10 feet. : ;
permanently once paired. 2. Press the Stunt Button. You will hear beeping coming from the remote 4. Drone is ready for flight. 3. Move the Multi Directional Button to the desired direction that you would like the drone to flip 4. Once you are comfortable with Stunt Mode, you can create multiple flips. Press the Stunt Always turn off remote prior to retrieving Button and then move the Multi Directional Button to the desired direction you would like the or picking up drone. This will help you drone to flip, continue to hold the joystick in the desired direction of the stunt. The drone will avoid accidently activating propellers. continue to flips in the direction you held the joystick, for a maximum of 3 stunts in a row. Step 6 - Operating Drone in Flight The drones range is approximately 150 feet
+ Read and be aware of all warnings found on page 1.
+ Maintain your desired elevation by using the Throttle
+ Use the Throttle joystick in a circle motion to spin the drone
- Use the Multi Directional Joystick to move forwards, backwards, and side to side
+ Review step 5 if your drone begins to drift Page 5 Page 6 Page 7 Rechargeable 2.4GHz STUNT DRONE CUSTOMER SERVICE
(800) 374-2744 TIPS
+ Do not crash drone into sand or dirt. Drone gears may become clogged
+ When first learning to fly, practice lifting off and hovering
+ Stay several feet from walls and buildings
+ Always Press Throttle all the way down after crashing or when something gets stuck in propellers
+ Never fly drones above or near people, sudden changes in wind or other conditions could lead to unexpected crashes.
+ Always use caution when flying drone vehicles, obey relevant laws, respect the privacy and property rights of others.
+ The drone shall never be modified or used for anything except its intended purpose. WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. TROUBLESHOOTING:
When remote switch is turned on, the remote light does not illuminate:
1) Check that batteries in the remote are installed correctly OR 2) Replace with new batteries During drone flight, the remote LED is flashing:
1) Remote batteries are low; replace them with new batteries Drone and remote properly pair, but the drone will not lift-off:
1) Drone Li-Po needs charging. Use charging cable to connect the drone to power source. After trimming the drone, the drone flight is very unstable and cannot fly properly:
1) One or more blades are most likely damaged;
2) Turn off the drone and remote. 3) Replace with the proper number replacement blade and try flying again. After impact, the drone is unstable:
1) Put the left remote control lever to the left bottom and put the right remote control lever to the right bottom at the same time which connected to the drone (diagram to right). 2) _ If the above does not resolve the issue, reboot the drone and controller and pair again. Remote Controller and Drone can not be paired:
1) Check Point: Remote Controller must be closed to Drone, not exceed 4 meters. Note: If there are 2 sets of Drones within 4 meters for Pairing, you must pair one successfully before pairing the second set. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two INFORMATION FOR FUTURE REFERENCE, conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. 2017 MerchSource, LLC. All rights reserved. Distributed by MerchSource, LLC, Irvine, CA 92618. Note: This equipment has been tested and found to comply with the limits for a Class B digital For technical support, please visit www.merchsource.com or call device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable 1-800-374-2744, protection against harmful interference in a residential installation. This equipment generates, The artwork and design of this manual are protected by US copyright law uses and can radiate radio frequency energy and, if not installed and used in accordance and may not be reproduced, distributed, displayed, published or used for with the instructions, may cause harmful interference to radio communications. any purpose without prior written permission. It is not permitted to alter, However, there is no guarantee that interference will not occur in a particular installation. If remove or reproduce any trademarks or copyright notice from this this equipment does cause harmful interference to radio or television reception, which can be manual. determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. PATENT PENDING Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Printed in China Consult the dealer or an experienced radio/TV technician for help. Dus to continuous product improvements, the picture on the manual may differ slightly from the actual product. Page 8