all | frequencies |
|
exhibits | applications |
---|---|---|---|---|
manual |
app s | submitted / available | |||||||
---|---|---|---|---|---|---|---|---|
1 2 3 |
|
User manual | Users Manual | 2.64 MiB | ||||
1 2 3 | Cover Letter(s) | |||||||
1 2 3 |
|
External photos | External Photos | 557.89 KiB | ||||
1 2 3 | Internal Photos | |||||||
1 2 3 | ID Label/Location Info | |||||||
1 2 3 | Test Report | |||||||
1 2 3 | Test Report | |||||||
1 2 3 | Test Setup Photos | |||||||
1 2 3 | RF Exposure Info | |||||||
1 2 3 | Test Report |
1 2 3 | User manual | Users Manual | 2.64 MiB |
Version: V1.00.000 Revised date: 2016-11-14 LAUNCH X-431 PRO MINI User Manual Copyright Information Copyright 2016 by LAUNCH TECH. CO., LTD. All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording or otherwise, without the prior written permission of LAUNCH. The information contained herein is designed only for the use of this unit. LAUNCH is not responsible for any use of this information as applied to other units. Neither LAUNCH nor its affiliates shall be liable to the purchaser of this unit or third parties for damages, losses, costs, or expenses incurred by purchaser or third parties as a result of: accident, misuse, or abuse of this unit, or unauthorized modifications, repairs, or alterations to this unit, or failure to strictly comply with LAUNCH operating and maintenance instructions. LAUNCH shall not be liable for any damages or problems arising from the use of any options or any consumable products other than those designated as Original LAUNCH Products or LAUNCH Approved Products by LAUNCH. Trademark Information LAUNCH is a registered trademark of LAUNCH TECH CO., LTD. (also called LAUNCH for short) in China and other countries. All other LAUNCH trademarks, service marks, domain names, logos, and company names referred to in this manual are either trademarks, registered trademarks, service marks, domain names, logos, company names of or are otherwise the property of LAUNCH or its affiliates. In countries where any of the LAUNCH trademarks, service marks, domain names, logos and company names are not registered, LAUNCH claims other rights associated with unregistered trademarks, service marks, domain names, logos, and company names. Other products or company names referred to in this manual may be trademarks of their respective owners. You may not use any trademark, service mark, domain name, logo, or company name of LAUNCH or any third party without permission from the owner of the applicable trademark, service mark, domain name, logo, or company name. You may contact LAUNCH by visiting the website at www.cnlaunch.com, or writing to LAUNCH TECH. CO., LTD.Launch Industrial Park, North of Wuhe Avenue, Banxuegang, Bantian, Longgang, Shenzhen, Guangdong, P.R.China, to request written permission to use Materials on this manual for purposes or for all other questions relating to this manual. i LAUNCH X-431 PRO MINI User Manual Important Safety Precautions Important: To avoid personal injury, property damage, or accidental damage to the product, read all of the information in this section before using the product.
Never collide, throw, or puncture X-431 PRO MINI, and avoid falling, extruding and bending it.
Do not insert foreign objects into or place heavy objects on your device. Sensitive components inside might cause damage.
Do not use X-431 PRO MINI in exceptionally cold or hot, dusty, damp or dry environments.
In places using X-431 PRO MINI may cause interference or generate a potential risk, please turn it off.
X-431 PRO MINI is a sealed unit. There are no end-user serviceable parts inside. All internal repairs must be done by an authorized repair facility or qualified technician. If there is any inquiry, please contact the dealer.
Never place X-431 PRO MINI into apparatus with strong electromagnetic field.
Keep X-431 PRO MINI far away from magnetic devices because its radiations can damage the screen and erase the data stored on X-431 PRO MINI.
DANGER: Do not attempt to replace the internal rechargeable lithium battery. Contact the dealer for factory replacement.
CAUTION: Please use the included battery and charger. Risk of explosion if the battery is replaced with an incorrect type.
Do not disconnect power abruptly when X-431 PRO MINI is being formatted or in process of uploading or downloading. Or else it may result in program error.
Do not delete unknown files or change the name of files or directories that were not created by you, otherwise your X-431 PRO MINI software might fail to work.
Be aware that accessing network resources can leave your X-431 PRO MINI vulnerable to computer viruses, hackers, spyware, and other malicious activities that might damage your device, software or data. It is your responsibility to ensure that you have adequate protection in the forms of firewalls, antivirus software, and anti-spyware software and keep such software up to date. Precautions on Using X-431 PRO MINI Before using this test equipment, please read the following safety information carefully. ii LAUNCH X-431 PRO MINI User Manual
Always perform automotive testing in a safe environment.
If the VCI module remains unused for a long period of time, it is suggested to unplug the connector from vehicles DLC to conserve battery power.
Wear an ANSI-approved eye shield when testing or repairing vehicles.
The vehicle shall be tested in a well ventilated work area, as engines produce various poisonous compounds (hydrocarbon, carbon monoxide, nitrogen oxides, etc.)
Do not connect or disconnect any test equipment while the ignition is on or the engine is running.
Put blocks in front of the drive wheels and never leave the vehicle unattended while testing.
Keep the test equipment dry, clean, free from oil, water or grease. Use a mild detergent on a clean cloth to clear the outside of the equipment as necessary.
Do not drive the vehicle and operate the test equipment at the same time. Any distraction may cause an accident.
Keep clothing, hair, hands, tools, test equipment, etc. away from all moving or hot engine parts.
Before starting the engine, put the gear lever in the Neutral position (for manual transmission) or in the Park (for automatic transmission) position to avoid injury.
To avoid damaging the test equipment or generating false data, please make sure the vehicle battery is fully charged and the connection to the vehicle DLC (Data Link Connector) is clear and secure.
Automotive batteries contain sulfuric acid that is harmful to skin. In operation, direct contact with the automotive batteries should be avoided. Keep the ignition sources away from the battery at all times. Precautions on Operating Vehicles ECU
Do not disconnect battery or any wiring cables in the vehicle when the ignition switch is on, as this could avoid damage to the sensors or the ECU.
Do not place any magnetic objects near the ECU. Disconnect the power supply to the ECU before performing any welding operations on the vehicle.
Use extreme caution when performing any operations near the ECU or sensors. Ground yourself when you disassemble PROM, otherwise ECU and sensors can be damaged by static electricity.
When reconnecting the ECU harness connector, be sure it is attached firmly, otherwise electronic elements, such as ICs inside the ECU, can be damaged. iii LAUNCH X-431 PRO MINI User Manual TABLE OF CONTENTS 1 INTRODUCTIONS........................................................................................... 1 1.1 PRODUCT PROFILE................................................................................. 1 1.2 FEATURES.............................................................................................. 1 1.3 KNOWLEDGE OF X-431 PRO MINI.......................................................... 2 1.3.1 X-431 PRO MINI whole set .............................................................. 2 1.3.2 X-431 PRO MINI handset................................................................. 2 1.3.3 VCI module (Only applies for 12V cars)........................................... 3 1.4 TECHNICAL PARAMETERS....................................................................... 4 1.5 PACKAGE LIST........................................................................................ 5 2 PREPARATIONS............................................................................................. 6 2.1 CHARGING X-431 PRO MINI ..................................................................... 6 2.2 USING YOUR BATTERY................................................................................ 6 2.3 POWER ON/OFF.......................................................................................... 6 2.3.1 Power on........................................................................................... 6 2.3.2 Power off........................................................................................... 6 2.4 TIPS ON FINGER OPERATIONS..................................................................... 6 2.5 LOCK & UNLOCK THE SCREEN .................................................................... 7 2.5.1 Lock the screen ................................................................................ 7 2.5.2 Unlock the screen............................................................................. 7 2.6 SCREEN LAYOUT........................................................................................ 8 2.7 NOTIFICATION PANEL ................................................................................. 8 2.8 CUSTOMIZE YOUR DESKTOP....................................................................... 8 2.8.1 Create a widget on the desktop........................................................ 8 2.8.2 Move items on the desktop .............................................................. 8 2.8.3 Delete items from the desktop.......................................................... 8 2.8.4 Adjust brightness .............................................................................. 8 2.8.5 Set standby time............................................................................... 8 2.9 SET SCREEN LOCK ..................................................................................... 9 3 WI-FI SETTING ............................................................................................. 10 3.1 CONNECT TO A WI-FI NETWORK ............................................................... 10 3.2 DISCONNECT FROM A WI-FI NETWORK ..................................................... 10 4 HOW TO DIAGNOSE.....................................................................................11 4.1 DIAGNOSIS FLOWCHART .......................................................................... 11 4.2 INITIAL USE.............................................................................................. 11 4.2.1 User registration ..............................................................................11 4.2.2 Diagnostic software layout.............................................................. 15 iv LAUNCH X-431 PRO MINI User Manual 4.2.3 Function menu................................................................................ 15 4.3 CONNECTIONS ......................................................................................... 16 4.3.1 Preparation ..................................................................................... 16 4.3.2 DLC location ................................................................................... 16 4.3.3 Vehicle connection.......................................................................... 16 4.4 BLUETOOTH SETTING............................................................................... 18 4.5 START DIAGNOSING................................................................................. 18 4.5.1 Read DTC....................................................................................... 20 4.5.2 Clear fault memory ......................................................................... 22 4.5.3 Read data stream ........................................................................... 22 4.5.4 Special function .............................................................................. 24 4.5.5 How to view History? ...................................................................... 24 4.6 REMOTE DIAGNOSIS ................................................................................ 25 4.6.1 Interface layout ............................................................................... 25 4.6.2 How to launch a remote diagnosis? ............................................... 26 4.7 SOFTWARE UPDATE................................................................................. 26 4.8 MAINTENANCE HELP ................................................................................ 26 4.9 PERSONAL CENTER ................................................................................. 27 4.9.1 My report......................................................................................... 27 4.9.2 My connector .................................................................................. 27 4.9.3 Activate connector .......................................................................... 27 4.9.4 Firmware fix .................................................................................... 27 4.9.5 Diagnostic feedback ....................................................................... 27 4.9.6 Profile.............................................................................................. 27 4.9.7 Change password........................................................................... 28 4.10 SETTINGS .............................................................................................. 28 4.10.1 Units of measurement .................................................................. 28 4.10.2 Print information ........................................................................... 28 4.10.3 Launch wireless printer connection.............................................. 28 4.10.4 Network test.................................................................................. 30 4.10.5 About............................................................................................. 30 4.10.6 Exit................................................................................................ 30 5 OTHERS........................................................................................................ 31 5.1 EMAIL ...................................................................................................... 31 5.1.1 Configure an email account............................................................ 31 5.1.2 Add an email account ..................................................................... 31 5.2 BROWSER................................................................................................ 31 5.2.1 Open browser ................................................................................. 31 5.2.2 Download files ................................................................................ 32 v LAUNCH X-431 PRO MINI User Manual 5.3 SYNCHRONIZATION .................................................................................. 32 5.3.1 Connect to PC ................................................................................ 32 5.3.2 Run on PC ...................................................................................... 32 5.3.3 Install an application ....................................................................... 32 5.4 CLEAR CACHE ......................................................................................... 33 6 FAQ ............................................................................................................... 34 vi LAUNCH X-431 PRO MINI User Manual 1 Introductions 1.1 Product Profile X-431 PRO MINI is a stylish Android-based vehicle trouble diagnostic tool. It inherits from LAUNCHs advanced diagnosing technology and is characterized by covering a wide range of vehicles, featuring powerful functions, and providing precise test result. Through the simple Bluetooth communication between the VCI module and X-431 PRO MINI, it achieves full car model and full system vehicle trouble diagnosis, which includes Reading DTCs, Clearing DTCs, Reading Data Stream, Actuation Test and Special Functions. Moreover, it supports Wi-Fi connection, which enables you surf the Internet, update the diagnostic software online and perform remote diagnosis etc, getting your job fixed faster and easier. 1.2 Features 1. Diagnostic Tool:
A. Diagnose
Diagnose the electronic control system of prevailing vehicle models covering Asian, European, American and Chinese. Diagnosis functions include: Read DTCs, Clear DTCs, Read data stream, Special functions etc.
Specially designed for Android platform with clear and user-friendly interface. PRO MINI.
Via Bluetooth, it is simple for the VCI module to communicate with X-431 B. One-click Update: lets you update your diagnostic software more efficiently. C. Repair Data: provides abundant automotive handbook, repair case and wiring diagrams for reference and retrieval. D. Remote Diagnosis: configures X-431 PRO MINI as an I/M(Instant Messaging) tool, which enables technicians to exchange repair experience and perform remote assistance more conveniently. 2. Browser: built-in Wi-Fi module makes surfing on the internet freely. 3. Email: allows you to send and receive emails. 4. Settings: to configure your personalized X-431 PRO MINI through it. 5. Applications: other android based applications can be customized to install 1 LAUNCH X-431 PRO MINI User Manual or uninstall. 1.3 Knowledge of X-431 PRO MINI 1.3.1 X-431 PRO MINI whole set X-431 PRO MINI is mainly composed of an X-431 PRO MINI handset, and a VCI module. 1.3.2 X-431 PRO MINI handset Fig. 1-1 X-431 PRO MINI tablet 1 VCI module 2 LAUNCH X-431 PRO MINI User Manual 2 3 4 5 6 7 8 Rear camera Camera flash Slot for VCI module POWER/Screen lock key Carry strap Speakers USB/Charging port 9 Microphone LCD screen 10 11 VOLUME +/- Key 12 Receiver 13 14 Earphone Jack Front camera For housing the VCI module. In Off mode, press it to turn X-431 PRO MINI on;
In On mode, turn X-431 PRO MINI off with long press or lock screen with short press. To connect to the power adaptor for charging. To adjust the volume. To print the screen, hold and press the POWER and VOLUME key until a snapshot pops up on the screen. The captured snapshot is saved in the Screenshots folder. 1.3.3 VCI module (Only applies for 12V cars) Fig. 1-2 VCI module 3 LAUNCH X-431 PRO MINI User Manual OBD-16 diagnostic connector Mini USB port Mode indicator To connect on vehicles OBD2 DLC. For connecting the USB cable to the tablet to perform vehicle diagnosis. (Note: This port is disabled for X-431 PRO MINI.)
It illuminates red when the VCI module is connected to the vehicles DLC.
Blue indicates the VCI module is working in Bluetooth mode. 1.4 Technical Parameters X-431 PRO MINI:
Operating system Processor Memory Storage LCD screen Camera Battery Connectivity Working temperature Storage temperature VCI module:
Android 5.1 Quad core 1.3 GHz 2GB 16GB 6.9 inch with a resolution of 1280 x 720 pixels Front-facing 2MP camera + rear-facing 5MP camera 3.7V/3000mh rechargeable polymer lithium battery
Wi-Fi: WLAN 802.11b/g/n
Bluetooth: Bluetooth 4.1 0 ~ 45
-10 ~ 50 Working voltage Average working current Standby current Working temperature Storage temperature Relative humidity 9 ~18V About 85mA About 55mA
-10 ~ 55
-20 ~ 70 20% ~ 90%
4 LAUNCH X-431 PRO MINI User Manual 1.5 Package List While opening X-431 PRO MINI package for the first time, please carefully check the following components. Common accessories for each X-431 PRO MINI are same, but for different destinations, the accessories of X-431 PRO MINI may vary. Please consult from the local agency or check the package list supplied with X-431 PRO MINI together.
X-431 PRO MINI tablet Password envelope VCI module (For connecting OBD II vehicles) OBD II extension cable OBD I adaptor (For connecting the non-16pin diagnostic connector and the VCI module) Battery clamps cable Power adaptors Non-16pin connectors (For connecting non-OBD II vehicle)
5 LAUNCH X-431 PRO MINI User Manual 2 Preparations 2.1 Charging X-431 PRO MINI 1. Plug one end of the included power adaptor into the USB port of the X-431 PRO MINI. 2. Connect the other end to the AC outlet. If into from X-431 PRO MINI. appears on the screen, it indicates it is being charged. If the logo changes
, it indicates that the battery is fully charged. Unplug the power adaptor 2.2 Using your battery
If the battery remains unused for a long period of time or the battery is completely discharged, it is normal that the tool will not power on while being charged. Please charge it for a period of 5 minutes and then turn it on.
Please use the included power adaptor to charge your tool. No responsibility can be assumed for any damage or loss caused as a result of using power adaptors other than the one supplied.
While X-431 PRO MINI has low battery, a beep will sound. If it is very low, X-431 PRO MINI will be switched off automatically. 2.3 Power on/off 2.3.1 Power on Press [POWER] to turn the tool on. Note: If it is the first time you have used this tool or the tool remains idle for a long period of time, the tool could fail to turn on. Please charge the tool for a minimum of 5 minutes and attempt to turn on again. 2.3.2 Power off Press [POWER] for 3 seconds, an option menu will pop up on the screen. Tap Power off to turn the tool off. 2.4 Tips on finger operations Single-tap: To select an item or launch a program. 6 LAUNCH X-431 PRO MINI User Manual Double-tap: To zoom in so that the text on a webpage appears in a column that fits your devices screen. Long press: Tap and hold on the current interface or area until a contextual menu pops up on the screen, and then release it. Slide: To jump to different pages. Drag: Tap the application icon and drop it to other location. Spread apart/pinch together: To zoom in manually, place two fingers on the screen and then spread them apart. To zoom out, place two fingers apart on the screen and then pinch them together. 2.5 Lock & unlock the screen Many screen lock modes are available on X-431 PRO MINI. Note: You are recommended to set screen lock as None since X-431 PRO MINI is a frequently used diagnostic tool. 2.5.1 Lock the screen
When it is ON, press [POWER] once to lock the screen;
The system will lock the screen automatically after X-431 PRO MINI remains idle over the preset standby time. 2.5.2 Unlock the screen Press [POWER] to activate the screen and drag the lock to Unlock position. Note: If you define as unlock using the pattern, you have to draw the right target pattern to unlock it. 7 LAUNCH X-431 PRO MINI User Manual 2.6 Screen layout There are four on-screen buttons available on the bottom of the screen. BACK HOME to navigate to the Androids home screen. to return to the previous screen. Tap Tap Recent Apps Tap to view the recently launched applications. 2.7 Notification panel The notification bar is used to display some activities, such as new message, to do list and running tasks. You can also open the notification bar to view the reminder or activity notification. 2.8 Customize your desktop 2.8.1 Create a widget on the desktop Tap and hold the desired application or widget, and then drag it to the target position. 2.8.2 Move items on the desktop Tap and hold the item to be moved, and drag and drop it to the target location. 2.8.3 Delete items from the desktop Warning: Deleting an icon will uninstall the corresponding application. Please be careful to do so. 1. Tap and hold the item to be moved until it is shaken. 2. Drag it on the trash icon and release it. Note: If no trash icon appears on the top of the screen, it indicates that the application cannot be uninstalled. 2.8.4 Adjust brightness Tips: Reducing the brightness of the screen is helpful to save the power of X-431 PRO MINI. 1. On the home screen, tap Settings > Display > Brightness level. 2. Drag the slider to adjust it. 2.8.5 Set standby time If no activities are made within the defined standby period, the screen will be 8 LAUNCH X-431 PRO MINI User Manual locked automatically and the system enters sleep mode to save power. 1. On the home screen, tap Settings > Display > Sleep. 2. Choose the desired sleep time. 2.9 Set screen lock This function is designed to lock the screen and buttons to avoid accidental operations while X-431 PRO MINI keeps unused. 1. On the home screen, tap Settings > Security > Screen lock. 2. Choose the desired screen lock mode and follow the on-screen instructions to finish your setting. Note: You are recommended to set screen lock as None since X-431 PRO MINI is a frequently used diagnostic tool. 9 LAUNCH X-431 PRO MINI User Manual 3 Wi-Fi Setting Note: If you dont need to use Wi-Fi for a while, you can turn it off to conserve battery life. X-431 PRO MINI has built-in Wi-Fi that can be used to get online. Once youre online, you can register your X-431 PRO MINI, surf the Internet, get apps, send email, launch the remote diagnosis, and check for software updates etc. 3.1 Connect to a Wi-Fi network 1. On the home screen, tap Settings > WLAN. 2. Slide the Wi-Fi switch to ON, X-431 PRO MINI will start searching for available wireless networks. 3. Select a wireless network,
the chosen network If automatically;
If the selected network is encrypted, a network password will need to be entered. is open, X-431 PRO MINI will connect 4. When Connected appears, it indicates the Wi-Fi connection is complete. Note: When Wi-Fi is not required, this should be disabled to conserve battery power. Once it is connected successfully, tap the Wi-Fi network from the list to view its name, link speed, security type, IP address etc. When this tool is in range, it will connect to the previously linked network automatically. 3.2 Disconnect from a Wi-Fi network 1. On the home screen, tap Settings > WLAN. 2. Tap the network with a Connected status, then tap Disconnect. 10 LAUNCH X-431 PRO MINI User Manual 4 How To Diagnose 4.1 Diagnosis Flowchart For new users, please follow the operation chart shown in Fig. 4-1 to get familiar with and start using X-431 PRO MINI. Fig. 4-1 4.2 Initial Use During initial use, tap the X-431 PRO MINI icon on the home screen to launch it and enter the main menu screen. 4.2.1 User registration Tap Login on the upper right corner of the main menu screen:
11 LAUNCH X-431 PRO MINI User Manual 1. If you are a new user, tap New Registration. See Fig. 4-3. Fig. 4-2 Fig. 4-3 Note: To obtain better service, you need to provide real information. A. Create App account: In Fig. 4-3, fill in the information in each field and then tap Register, a screen similar to the following will appear:
12 LAUNCH X-431 PRO MINI User Manual B. Activate the VCI module: In Fig. 4-4, input the Serial Number and Activation Code, which can be found in the password envelope. Fig. 4-4 Product SN Product SN Activation code Fig. 4-5 Note: To exit and activate it later, tap Skip. In this case, you can activate your connector by tapping Activate Connector in Personal Center. For details, please refer to Chapter 4.9.3 Activate Connector. C. Download diagnostic software: Tap Activate, a dialog box similar to Fig. 4-6 will appear:
13 LAUNCH X-431 PRO MINI User Manual To download the diagnostic software, tap Yes to enter the software download page. Tap No to download it later. Fig. 4-6 Fig. 4-7 On the download page, tap Update to start downloading. It may take several minutes to finish it, please be patient to wait. To pause downloading, tap Pause. To resume it, tap Continue. Once download is complete, the system will install the software package automatically. 2. If you have registered to be a member, input your name and password, and then tap the Login button to enter the main menu screen directly. 3. If you forgot the password, tap Retrieve Password, and then follow the on-screen instructions to retrieve it. 14 LAUNCH X-431 PRO MINI User Manual 4.2.2 Diagnostic software layout Fig. 4-8 1 2 3 4 5 Tap to navigate to the main function menu. Refer to Chapter 4.2.3 Function menu for details. Search bar: input the desired vehicle model name to locate it quickly. History tab: Generally once a vehicle diagnosis is performed, the system will record the every details of diagnostic process. This function provides a quick access to the tested vehicles and users can resume from the last operation, without the necessity of starting from scratch. Vehicle region buttons: Tap different buttons to switch to corresponding vehicles. VINscan button: Tap it to scan the Vehicle Identification Number (VIN) code of your vehicle. OBD VIN and INPUT VIN are included. Note: Before using this function, the corresponding diagnostic software and Auto search file need to be downloaded on your tool first while downloading the diagnostic software. 4.2.3 Function menu It mainly includes the following items:
Name Tradition Diagnose Configures X-431 PRO MINI Description Remote Diagnosis Software Upgrade Maintenance Help to operate as a diagnostic tool. This option aims to help repair shops or technicians to get the repair job fixed faster. To update vehicle diagnostic software. Includes How-to Videos, operation skills and user manual etc. 15 LAUNCH X-431 PRO MINI User Manual Personal Center Allows you to configure system settings and manage your personal information. 4.3 Connections 4.3.1 Preparation Normal testing conditions
Turn on the vehicle power supply.
Vehicle battery voltage range should be 9-14 Volts.
Throttle should be in a closed position. Select the VCI module If X-431 PRO MINI is testing vehicles equipped with universal OBD II 16 PIN diagnostic socket, please use the included VCI module. (For vehicles with non-OBD II 16 PIN diagnostic socket, a non-16 PIN connector is required.) 4.3.2 DLC location The DLC (Data Link Connector) is typically a standard 16-pin connector where diagnostic tools interface with a vehicles on-board control modules. The DLC is usually located 12 inches from the center of the instrument panel, under or around the drivers side for most vehicles. If DLC is not located under dashboard, a label should be there telling location. For some Asian and European vehicles, the DLC is located behind the ashtray and the ashtray must be removed to access the connector. If the DLC cannot be found, refer to the vehicles service manual. Fig. 4-9 4.3.3 Vehicle connection The method used to connect the VCI module to a vehicles DLC depends on the 16 LAUNCH X-431 PRO MINI User Manual vehicles configuration as follows:
A vehicle equipped with an OBD II management system supplies both communication and 12V power through a standardized DLC.
A vehicle not equipped with an OBD II management system supplies communication through a DLC connection, and in some cases supplies 12V power through the cigarette lighter receptacle or a connection to the vehicle battery. Follow the steps mentioned below to connect OBD II vehicle:
1. Locate vehicles DLC socket. 2. Plug the VCI module into the vehicles DLC socket (It is suggested to use the OBD II extension cable to connect the VCI module and DLC socket.). Fig. 4-10 3. Choose one of the two ways to obtain power from:
A. Power adaptor: Connect one end of the included power adaptor to DC IN port of X-431 PRO MINI tablet, and the other end to AC outlet. B. Internal battery pack For non-OBDII vehicle, proceed as follows:
1. Locate vehicles DLC socket. 2. Select the corresponding non-16pin connector. 3. Plug the non-16pin end of the connector into the DLC socket, then connect the other end to the OBD I adaptor, and then tighten the captive screws. 4. Connect the other end of the adaptor to the included VCI module. 5. To supply power to OBD I adaptor from:
A. Cigarette Lighter cable(optional): Connect one end of the cigarette lighter cable to vehicles cigarette lighter receptacle, and the other end to the power jack of OBD I adaptor. 17 LAUNCH X-431 PRO MINI User Manual B. Battery Clamps Cable: Connect one end of the battery clamps cable to vehicles battery, and the other end to the power jack of OBD I adaptor. Fig. 4-11 Fig. 4-12 4.4 Bluetooth Setting Enter X-431 PRO MINI Bluetooth setting screen (Settings --> Bluetooth), slide the Bluetooth switch to ON and X-431 PRO MINI will start searching available Bluetooth device, tap the desired connector to pair. By default, the Bluetooth name is 98639*****00 (where ***** stands for 5 digits.). Note: In case no Bluetooth setting is done before diagnostic software is launched, you can also configure it while using the software. For details on Bluetooth connection, please refer to Chapter 4.5 Start diagnosing. 4.5 Start Diagnosing Tap Tradition Diagnose to enter the vehicle selection page. 2 approaches are provided for you to access the vehicle diagnostic software. Choose any one of the following ways:
1. VINSCAN enables you to access it more quickly. In this case, automatic scan (OBD VIN) and manual input (INPUT VIN) are 18 LAUNCH X-431 PRO MINI User Manual available. Fig. 4-13 OBD VIN: In this mode, the VCI module should be plugged into the vehicles DLC first, and then a Bluetooth communication should be established between X-431 PRO MINI and the vehicle. Tap OBD VIN to scan the vehicle identification number of the vehicle. Once scanning is complete and successful, X-431 PRO MINI will enter the diagnostic software of the vehicle. Note: Before using this function, the corresponding diagnostic software and Auto search file need to be downloaded on your tool first while downloading the diagnostic software. INPUT VIN: In this mode, you need to input the VIN manually. In general, vehicle identification numbers are standardized - all contain 17 characters. VIN characters may be capital letters A through Z and numbers 1 through 0;
however, the letters I, O and Q are never used in order to avoid mistakes of misreading. No signs or spaces are allowed in the VIN. The most recognizable location for this number is in the top left corner on the vehicles dashboard. Other locations include the drivers door or post, and the firewall under the hood. Tap INPUT VIN and a screen similar to Fig. 4-14 will appear:
Fig. 4-14 Input the VIN, and tap Confirm to enter the diagnostic software of the vehicle. 2. Tap a corresponding diagnostic software logo, and then follow the 19 LAUNCH X-431 PRO MINI User Manual on-screen instruction to access the diagnostic software. Take Demo as an example to demonstrate how to diagnose a vehicle. 1). Tap the DEMO to enter the software selection page. 2). Tap DEMO to ignore Bluetooth connection and jump to the DEMO system selection screen. (Note: No Bluetooth connection is required for DEMO program.) Fig. 4-15 Fig. 4-16 3). Tap Engine, the system will navigate to the test function menu. See Fig. 4-16. 4.5.1 Read DTC This function displays the detailed information of DTC records retrieved from the vehicles control system. Tap Read DTC in function menu, the screen will display the diagnostic result. 20 LAUNCH X-431 PRO MINI User Manual Fig. 4-17 to search the definition of the Highlight a certain DTC item, and then tap selected DTC online. On-screen Buttons:
Exit: Tap it to return to the home screen. Report: To save the current diagnostic data. All reports are saved under the tab Diagnostic Report in My Report from Profile menu. For details on report operations, please refer to Chapter 4.9.1 My Report. Freeze Frame: When an emission-related fault occurs, certain vehicle conditions are recorded by the on-board computer. This information is referred to as freeze frame data. Freeze frame data includes a snapshot of critical parameter values at the time the DTC is set. Help: Tap it to view the help information. 21 LAUNCH X-431 PRO MINI User Manual 4.5.2 Clear fault memory After reading the retrieved codes from the vehicle and certain repairs have been carried out, you can use this function to erase the codes from the vehicle. Before performing this function, please be sure the vehicles ignition key is in the ON position with the engine off. Tap Clear fault memory in function menu, the system will automatically delete the currently existing trouble code. Note: The trouble code will not disappear until the trouble was completely cleared. 4.5.3 Read data stream This option retrieves and displays live data and parameters from the vehicles ECU. Tap Read Data Stream in function menu, the system will display data stream items. Fig. 4-18 On-screen Buttons:
Select Page: Tap it to select all items of the current page. 22 LAUNCH X-431 PRO MINI User Manual Unselect: Tap it to deselect all data stream items. Exit: Tap it to return to the home screen. Print: Tap it to print the current screen. To perform printing, you need to purchase a Wi-Fi printer manufactured by LAUNCH separately. For details on printer setting, see Chapter 4.10.3 Launch wireless printer connection. Submit: Tap it to confirm and jump to the next step. After selecting the desired items, tap Confirm to enter the data stream reading page. Fig. 4-19 On-screen Buttons:
Exit: Tap to return to the home screen. Graph: After selecting, tap it to view the waveform. There are 3 types of display modes available for data viewing, allowing you to view various types 23 LAUNCH X-431 PRO MINI User Manual of parameters in the most suitable way.
Graph displays the parameters in waveform graphs.
Value this is the default mode which displays the parameters in texts and shows in list format.
Combine this option is mostly used in graph merge status for data comparison. In this case, different items are marked in different colors. Record: Tap to start recording diagnostic data for future playback and analysis. The saved file follows the naming rule: It begins with vehicle type, and ends with the record starting time (To differentiate between files, please configure the accurate system time). The file is stored in My Report under Personal Center menu. For details on playback operations, please refer to Chapter 4.9.1 My Report. To stop reading the data stream, tap Print: Tap it to print the current screen. To perform printing, you need to purchase a Wi-Fi printer manufactured by LAUNCH separately. For details on printer setting, see Chapter 4.10.3 Launch wireless printer connection. Help: Tap to view the help information. before the recording progress bar. If more than one page of data stream items is displayed, an icon similar to 1/X appears. Swipe the screen from right to left to switch to the next page. 4.5.4 Special function This option allows you to detect whether the system parameters are normal or not. It mainly includes: Injector test, fuel pump test, purge control solenoid and so on. Take 1# injector as an example. To detect whether 1# injector works normally or not, tap 1# injector, the system will automatically carry out the function. After complete, a prompt dialog box will pop up on the screen. 4.5.5 How to view History?
Generally once a vehicle diagnosis is performed, X-431 PRO MINI will record the every details of diagnostic process. The History function provides a quick access to the tested vehicles and users can resume from the last operation, without the necessity of starting from scratch. 1. Tap History, all diagnostic records will be listed on the screen in date sequence. Where the box with light blue background indicates that no DTCs are found on this vehicle and the light yellow box indicates that the vehicle has DTCs. 24 LAUNCH X-431 PRO MINI User Manual 2. Tap a certain box to enter the history records. 3. Tap Restore to directly jump to the system selection screen. 4. Tap the desired system to enter and follow the instructions on the screen to proceed. 4.6 Remote Diagnosis This option aims to help repair shops or technicians launch instant messaging and remote diagnosis, making the repair job getting fixed faster. Tap Remote Diagnosis to enter, the screen appears blank by default. 4.6.1 Interface layout Fig. 4-20 1 Search bar 2 Alphabetic order list Directly input the username of the X-431 PRO MINI to start searching, and then tap the desired one to add it into your friend list. The name of friends is sorted by alphabetic order. Tap the desired letter to quickly locate it. Tap to enter the friend list. 3 Contact tab 4 Message tab Once an incoming message reaches, a red dot will appear on the upper right corner of the tab. 25 LAUNCH X-431 PRO MINI User Manual 4.6.2 How to launch a remote diagnosis?
After adding your friend, you can tap it from the friend list to enter the instant messaging interface. Tap the input field and use the on-screen keyboard to enter the text message, and and then tap Send to send it; tap choose the desired file type to send. To perform the remote diagnosis, tap Remote Diagnostic, an option menu including the following will appear:
to send the voice message; tap Actions Results Send remote diagnostic reservation Tap it and input the reservation title of the remote diagnosis, and then tap Confirm to send. Request control remote device Request to control the partners device remotely to help him diagnose the vehicle. Invite remote diagnostic assistant Cancel If you need assistance, just use this option to invite a technician to perform a remote control on your tool. Notes: In this case,
To perform this function, you need to download and install the corresponding vehicle diagnostic software.
Make sure the VCI module is properly connected to the vehicles DLC and the Bluetooth communication between your X-431 PRO MINI and the VCI module works smoothly. To cancel this operation. 4.7 Software Update Before diagnosing a vehicle, you have to download the corresponding vehicle diagnosis software. Tap Software Upgrade to enter the update center. Tap Update to start downloading. Once downloading is finished, the software packages will be installed automatically. 4.8 Maintenance Help This option provides abundant repair case and automotive technology handbook for your reference. 26 LAUNCH X-431 PRO MINI User Manual 4.9 Personal Center This function allows users to manage your personal information, configure system settings and feedback your vehicle issues or diagnostic reports to us for analysis. 4.9.1 My report This option is used to view the diagnostic report generated in process of vehicle diagnosis. Additionally, delete, share operations are also supported. Tap My Report, there are total 3 options available. If user records the running parameters while reading data stream, it will be saved as .x431 file and appear under Diagnostic Record tab. Remote Diagnostic Report lists all records generated in process of remote diagnosis. In case the DTC result is saved on Read Trouble Code page, the files will be listed under Diagnostic Report tab. 4.9.2 My connector This option is used to manage all your activated connectors. If several VCI modules are activated on this tool, a list of connectors will be displayed on the screen. Once you choose the connector that belongs to other account, you have to log out, and then input the right account to continue. 4.9.3 Activate connector It is used to activate your VCI module. Input the Serial Number and Activation Code, and then tap Activate to activate it. For details on how to obtain Serial Number and Activation Code, tap the link below to get help. 4.9.4 Firmware fix Use this item to upgrade and fix diagnostic firmware. During fixing, please do not cut power or switch to other interfaces. 4.9.5 Diagnostic feedback This item allows you to feedback your diagnostic problems to us for analysis and troubleshooting. 4.9.6 Profile Use this item to view and configure personal information. 27 LAUNCH X-431 PRO MINI User Manual 4.9.7 Change password This item allows you to modify your login password. 4.10 Settings It enables you to make some application settings and view software version information etc. 4.10.1 Units of measurement It is designed to set the measurement unit. Metric System and English System are available. 4.10.2 Print information This option lets you define your print information. It mainly includes Workshop, Address, Telephone, Fax and License Plate. After inputting, tap on Save to save it. 4.10.3 Launch wireless printer connection This option is designed to establish a wireless connection between X-431 PRO MINI and the Wi-Fi printer (sold separately) while performing printing operations. Follow the steps below to connect the printer. 1. Tap Launch Wireless Printer Connection;
Fig. 4-21 A. If it is the first time you have operated this printer, please proceed the following:
2. For initial use, you are suggested to reset the printer: Press and hold [MODE]
& [FEED] for 8 seconds, the following resetting command will be printed out:
at + default = 1 28 LAUNCH X-431 PRO MINI User Manual ok at + reboot = 1 rebooting... 3. Tap Reset to configure Wi-Fi printer. Step 1: Connect the printer:
Tap the desired printer hotspot named with X-431PRINTER-XXXX (XXXX stands for 4 characters), and then tap Connect to enter Step 2. to select Scan Fig. 4-22 Step 2: Join the Wi-Fi printer into LAN:
Tap Scan to select the desired local Wi-Fi network from the list, and type in the security password (If it is an open network, password is not required), and then tap Confirm. 1. Once the Wi-Fi network of the printer is connected and the printer is found, Fig. 4-23 29 LAUNCH X-431 PRO MINI User Manual tap Printing test to test the printing. Fig. 4-24 Now you can use the Wi-Fi printer to print!
If the printer is not found, please reset the printer to default factory settings (refer to Step 2 for details) and check whether the current device and the printer are on the same LAN. B. If you have configured the Wi-Fi printer to the LAN:
2. Tap Connect to Printer:
a). If the local network remains as it is, tap Test Print directly to test the printing. b). If the local network changes, you have to reset the Wi-Fi printer. 4.10.4 Network test It enables you to test whether the current network environment is good or not. It is normal that you may encounter a logout while testing. 4.10.5 About The software version information and disclaimer are included. 4.10.6 Exit This option allows you to logout the system. To logout the current user ID, tap Exit from current account. 30 LAUNCH X-431 PRO MINI User Manual 5 Others 5.1 Email The function allows you to send and receive emails. 5.1.1 Configure an email account Note: Before sending or receiving email, you have to set up an email account. In addition, this function requires a stable network connection. 1. On the home screen, tap Email. 2. Choose the desired email account type. 3. Input email address and password, tap Next. Note: If Manual setup is selected, please consult your email service provider for detailed parameter setting. 4. Follow the on-screen instructions to proceed until the system prompts you that the account setup has been finished. 5.1.2 Add an email account 1. Tap Settings --> Accounts. 2. Tap Add account. 3. Choose the desired account type. 5.2 Browser 5.2.1 Open browser On the home screen, tap Browser to launch the browser. You can choose the desired homepage or input the website address to browse. Fig. 5-1 1 2 3 Return to the previous page. Advance to the recently visited page. Refresh the current page. 31 LAUNCH X-431 PRO MINI User Manual 4 5 6 7 8 9 10 Close the current page. Create a new tab. Input a web address. Add the current page as bookmark. Open search bar. Open bookmark list. View more options. 5.2.2 Download files Files, pictures, and applications can be downloaded from the website in browser. For example:
Tap and hold a picture, then choose Save image from pop-up menu to download it. To download a link, tap and hold it, and then choose Save link. To protect your X-431 PRO MINI and personal data, please download applications from trusted sources. To configure it, tap Settings > Security, and then slide the Unknown sources switch to off. 5.3 Synchronization You can transfer media files and APK between the PC and X-431 PRO MINI. 5.3.1 Connect to PC 1. Use the USB cable to connect the X-431 PRO MINI to your PC. 2. Swipe from the top, a message Connected as a media device appears. 5.3.2 Run on PC Perform the following steps:
Locate the new disc.
Copy the files. 5.3.3 Install an application Do the following steps:
1. Tap Settings > Security, and set the Unknown sources to ON, which allows you to install apps from unknown sources. 2. A dialog box appears on the screen, tap OK to confirm. 3. Set the tool as Connected as a media device, and copy the APK file from the PC to the tool. 32 LAUNCH X-431 PRO MINI User Manual 5.4 Clear Cache Doing so clears all browsing records and accounts and enables X-431 PRO MINI to run smoothly and quickly. 1. Tap Settings > Apps. 2. Tap 3. Tap certain application, then tap Clear Cache to release the space these and select Sort by size to arrange all applications in size order. cache files are occupied. 33 LAUNCH X-431 PRO MINI User Manual 6 FAQ 1. How to save power?
Please turn off the screen while X-431 PRO MINI keeps idle.
Set a shorter standby time.
Decrease the brightness of the screen.
Disable GPS function if GPS service is not in use. 2. What should I do in case I forgot the screen lock?
You can set screen lock as pattern or password. If you forgot the password, please consult your device provider or reset your device. If WLAN connection is not required, please turn it off. Warning: Resetting may cause data loss. Before use, please make sure important data has been backed up. 3. How to do if the system runs slow?
In this case, please do the followings:
> Check all running applications and stop the unnecessary applications (Steps:
Settings --> Apps --> Running --> Tap the desired application and then tap Stop).
> Check all installed applications, remove the unnecessary applications (Steps:
Settings --> Apps --> Downloaded --> Tap the desired application and then tap Uninstall). If all steps mentioned above are finished and the system still works slowly. Please try to close the system and reboot your X-431 PRO MINI. 4. How to reset X-431 PRO MINI?
Resetting may cause data loss. Before doing so, please make sure important data and information has been backed up. Do the following to reset X-431 PRO MINI:
1. Tap Settings --> Back & Reset;
2. Tap Factory data reset;
3. Tap Reset tablet;
4. Tap Clear all data to start resetting until the tool automatically reboots. 5. Why some videos on the website can be not played?
It possibly results from:
1. The current browser does not support Flash playing;
34 LAUNCH X-431 PRO MINI User Manual 2. Flash player does not support this video. Try to use other browsers to watch it or install other Flash player. 6. The date and time of X-431 PRO MINI cannot be set. It is because Automatic date & time is set on your X-431 PRO MINI. Tap Settings --> Date & time, deselect Automatic date & time and then set the date and time manually. Since the diagnostic reports are saved and sorted by date, please make sure the system date and time is properly configured on this tool. 35 LAUNCH X-431 PRO User Manual Warranty Warranty THIS WARRANTY IS EXPRESSLY LIMITED TO PERSONS WHO PURCHASE LAUNCH PRODUCTS FOR PURPOSES OF RESALE OR USE IN THE ORDINARY COURSE OF THE BUYERS BUSINESS. LAUNCH electronic product is warranted against defects in materials and workmanship for one year from date of delivery to the user. This warranty does not cover any part that has been abused, altered, used for a purpose other than for which it was intended, or used in a manner inconsistent with instructions regarding use. The exclusive remedy for any automotive meter found to be defective is repair or replacement, and LAUNCH shall not be liable for any consequential or incidental damages. Final determination of defects shall be made by LAUNCH in accordance with procedures established by LAUNCH. No agent, employee, or representative of LAUNCH has any authority to bind LAUNCH to any affirmation, representation, or warranty concerning LAUNCH automotive meters, except as stated herein. Disclaimer The above warranty is in lieu of any other warranty, expressed or implied, including any warranty of merchantability or fitness for a particular purpose. Purchase Order Replaceable and optional parts can be ordered directly from your LAUNCH authorized tool supplier. Your order should include the following information:
Order quantity Part number Part name Customer Service Any question during the operation, please call 86-755-84528722. If your unit requires repair service, return it to the manufacturer with a copy of the sales receipt and a note describing the problem. If the unit is determined to be in warranty, it will be repaired or replaced at no charge. If the unit is determined to be out of warranty, it will be repaired for a nominal service charge plus return freight. Send the unit pre-paid to:
Attn: Customer Service Department LAUNCH TECH. CO., LTD. Launch Industrial Park, North of Wuhe Avenue, Banxuegang, Bantian, 36 LAUNCH X-431 PRO User Manual Warranty Longgang, Shenzhen, Guangdong P.R.China, 518129 Launch website: http://www. cnlaunch.com http://www.x431.com http://www.dbscar.com Statement:
LAUNCH reserves the rights to make any change to product designs and specifications without notice. The actual object may differ a little from the descriptions in the manual in physical appearance, color and configuration. We have tried our best to make the descriptions and illustrations in the manual as accurate as possible, and defects are inevitable, if you have any question, please contact local dealer or after-sale service center of LAUNCH, LAUNCH does not bear any responsibility arising from misunderstandings. 37 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
frequency | equipment class | purpose | ||
---|---|---|---|---|
1 | 2017-04-16 | JBP - Part 15 Class B Computing Device Peripheral | Original Equipment | |
2 | 2402 ~ 2480 | DSS - Part 15 Spread Spectrum Transmitter | ||
3 | 2412 ~ 2462 | DTS - Digital Transmission System |
app s | Applicant Information | |||||
---|---|---|---|---|---|---|
1 2 3 | Effective |
2017-04-16
|
||||
1 2 3 | Applicant's complete, legal business name |
Lightcomm Technology Co., Ltd.
|
||||
1 2 3 | FCC Registration Number (FRN) |
0018979138
|
||||
1 2 3 | Physical Address |
UNIT 1306 13/F ARION COMMERCIAL CENTRE
|
||||
1 2 3 |
HONG KONG, N/A
|
|||||
1 2 3 |
Hong Kong
|
|||||
app s | TCB Information | |||||
1 2 3 | TCB Application Email Address |
s******@nemko.com
|
||||
1 2 3 | TCB Scope |
A1: Low Power Transmitters below 1 GHz (except Spread Spectrum), Unintentional Radiators, EAS (Part 11) & Consumer ISM devices
|
||||
1 2 3 |
A4: UNII devices & low power transmitters using spread spectrum techniques
|
|||||
app s | FCC ID | |||||
1 2 3 | Grantee Code |
XMF
|
||||
1 2 3 | Equipment Product Code |
MID6901
|
||||
app s | Person at the applicant's address to receive grant or for contact | |||||
1 2 3 | Name |
J****** S********
|
||||
1 2 3 | Title |
Certification Manager
|
||||
1 2 3 | Telephone Number |
00852********
|
||||
1 2 3 | Fax Number |
00852********
|
||||
1 2 3 |
s******@hcn2000.com
|
|||||
app s | Technical Contact | |||||
n/a | ||||||
app s | Non Technical Contact | |||||
n/a | ||||||
app s | Confidentiality (long or short term) | |||||
1 2 3 | Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | Yes | ||||
1 2 3 | Long-Term Confidentiality Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | No | ||||
if no date is supplied, the release date will be set to 45 calendar days past the date of grant. | ||||||
app s | Cognitive Radio & Software Defined Radio, Class, etc | |||||
1 2 3 | Is this application for software defined/cognitive radio authorization? | No | ||||
1 2 3 | Equipment Class | JBP - Part 15 Class B Computing Device Peripheral | ||||
1 2 3 | DSS - Part 15 Spread Spectrum Transmitter | |||||
1 2 3 | DTS - Digital Transmission System | |||||
1 2 3 | Description of product as it is marketed: (NOTE: This text will appear below the equipment class on the grant) | MID | ||||
1 2 3 | Related OET KnowledgeDataBase Inquiry: Is there a KDB inquiry associated with this application? | No | ||||
1 2 3 | Modular Equipment Type | Does not apply | ||||
1 2 3 | Purpose / Application is for | Original Equipment | ||||
1 2 3 | Composite Equipment: Is the equipment in this application a composite device subject to an additional equipment authorization? | Yes | ||||
1 2 3 | Related Equipment: Is the equipment in this application part of a system that operates with, or is marketed with, another device that requires an equipment authorization? | No | ||||
1 2 3 | Grant Comments | Output power listed is conducted. | ||||
1 2 3 | Is there an equipment authorization waiver associated with this application? | No | ||||
1 2 3 | If there is an equipment authorization waiver associated with this application, has the associated waiver been approved and all information uploaded? | No | ||||
app s | Test Firm Name and Contact Information | |||||
1 2 3 | Firm Name |
Shenzhen Alpha Product Testing Co., Ltd.
|
||||
1 2 3 | Name |
M****** Z********
|
||||
1 2 3 | Telephone Number |
86-75********
|
||||
1 2 3 | Fax Number |
86-75********
|
||||
1 2 3 |
m******@a-lab.cn
|
|||||
Equipment Specifications | |||||||||||||||||||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
1 | 1 | 15B | |||||||||||||||||||||||||||||||||||||||
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
2 | 1 | 15C | 2402.00000000 | 2480.00000000 | 0.0016410 | ||||||||||||||||||||||||||||||||||||
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
3 | 1 | 15C | 2402 | 2480 | 0.001187 | ||||||||||||||||||||||||||||||||||||
3 | 2 | 15C | 2412 | 2462 | 0.008222 |
some individual PII (Personally Identifiable Information) available on the public forms may be redacted, original source may include additional details
This product uses the FCC Data API but is not endorsed or certified by the FCC