FCC ID: 2ARRD-AP6330 WIFI Module

User Manual MODEL No.:AP6330 1. Introduction AMPAK Technology would like to announce a low-cost and low-power consumption module which has all of the WiFi and FM functionalities. The highly integrated module makes the possibilities of web browsing, VoIP , FM radio functional applications and other applications. With seamless roaming capabilities and advanced security, also could interact with different vendors 802.11a/b/g/n Access Points in the wireless LAN. The wireless module complies with IEEE 802.11 a/b/g/n standard and it can achieve up to a speed of 72.2Mbps with single stream in 802.11n draft, 54Mbps as specified in IEEE 802.11g, or 11Mbps for IEEE 802.11b to connect to the wireless LAN. The integrated module provides SDIO interface for WiFi, UART / PCM interface for FM. This compact module is a total solution for a combination of WiFi + FM technologies. The module is specifically developed for Smart phones and Portable devices. The module is limited to being installed in a fixed device and cannot be used in a mobile device. While the module is being installed to the platform, the pertaining rule with regards to 15B must be evaluated. Further to the RF exposure, the device shall be installed to the mobile platform with 20cm, and not collated with other transmitters 2 2. Features 802.11a/b/g/n dual-band radio non-simultaneous dual-band operation Concurrent FM (RX) RDS/RBDS, and WLAN operation Simultaneous WLAN receive with single antenna WLAN host interface options:

- SDIO v2.0 up to 50 MHz clock rate FM multiple audio routing options: PCM, eSCO, A2DP ECI enhanced coexistence support, ability to coordinate SCO transmissions IEEE Co-existence technologies are integrated die solution around WLAN receives A simplified block diagram of the module is depicted in the figure below. 3 3. Deliverables 3.1 Deliverables The following products and software will be part of the product. Module with packaging Evaluation Kits Software utility for integration, performance test. Product Datasheet. Agency certified pre-tested report with the adapter board. 3.2 Regulatory certifications The product delivery is a pre-tested module, without the module level certification. For module approval, the platforms antennas are required for the certification. 4. General Specification 4.1 General Specification Model Name Product Description Dimension WiFi Interface Humidity AP6330 Support WiFi/FM functionalities L x W x H: 12 x 12 x 1.5 (typical) mm SDIOV2.0 Operating Humidity 10% to 95% Non-Condensing 4 5. WiFi RF Specification Characteristics Description IEEE 802.11 WLAN Mode Supported Data Rate Modulation 802.11b 802.11g 802.11n(20MHz channel bandwidth) 802.11 b:1,2,5.5,11Mbps;

802.11 g:6,9,12,18,24,36,48,54Mbps;

802.11n(HT20):MCS0-MCS7;

DSSS with DBPSK/DQPSK/CCK for 802.11b;

OFDM with BPSK/QPSK/16QAM/64QAM for 802.11g/n;

Operating Frequency Range Number of Channels 2412-2462MHz for 802.11b/g;

2412-2462MHz for 802.11n(HT20);

11 channels for 802.11b/g;

11 channels for 802.11n(HT20);

Transmit Power Max 21.12 dBm Antenna Type Integral antenna via a SMA connector Characteristics Description IEEE 802.11 WLAN Mode Supported 802.11a(20MHz channel bandwidth) 802.11n(20MHz channel bandwidth) Data Rate 802.11a:54/48/36/24/18/12/9/6 Mbps 802.11n:up to 600 Mbps Modulation OFDM with BPSK/QPSK/16QAM/64QAM for 802.11a/n;

Operating Frequency Range Transmit Power Max WIFI 5G Band Mode UNII Band I UNII Band III 13.86 dBm for UNII Band I 16.27dBm for UNII Band III 802.11a/n(HT20) 802.11a/n(HT20) Antenna Type Integral antenna via a SMA connector Frequency Range(MHz

) 5180-5240 5745-5825 Number of channels 4 5 5 Frequency and Channel list for 802.11 b/g/n(HT20):

Channel 1 2 3 4 Frequency

(MHz) 2412 2417 2422 2427 Channel 5 6 7 8 Frequency

(MHz) 2432 2437 2442 2447 Channel 9 10 11 Frequency

(MHz) 2452 2457 2462 Wifi 5G with UNII Band I Frequency and Channel list for 802.11a/n(HT20):

Channel 36 40 Frequency

(MHz) 5180 5200 Channel 44 48 Wifi 5G with UNII Band III Frequency and Channel list for 802.11a/n(HT20):

Channel 149 153 Frequency

(MHz) 5745 5765 Channel 157 161 Frequency

(MHz) 5220 5240 Frequency

(MHz) 5785 5805 Channel Frequency

(MHz) Channel 165 Frequency

(MHz) 5825 6 7. Pin Assignments 7.1 Pin Outline

< TOP VIEW >

7.2 Pin Definition NO 1 2 3 4 5 6 7 8 9 10 11 12 13 Name GND _ANT GND FM_RX NC _WAKE _HOST_WAKE NC VBAT XTAL_IN XTAL_OUT WL_REG_ON WL_HOST_WAKE Type I/O I I O P I O I O Description Ground connections RF I/O port Ground connections FM radio RF input antenna port Floating (Dont connected to ground) HOST wake-up Bluetooth device wake-up HOST Floating (Dont connected to ground) Main power voltage source input Crystal input Crystal output Internal regulators power enable/disable WLAN to wake-up HOST 11 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 SDIO_DATA_2 SDIO_DATA_3 SDIO_DATA_CMD SDIO_DATA_CLK SDIO_DATA_0 SDIO_DATA_1 GND VIN_LDO_OUT VDDIO VIN_LDO LPO PCM_OUT PCM_CLK PCM_IN PCM_SYNC NC NC GND NC GND RST_N NC GND NC NC NC NC UART_RTS_N UART_TXD UART_RXD UART_CTS_N TP1 TP2 TP3 (NC) I/O I/O I/O I/O I/O I/O P P P I I/O I/O I/O I/O I O O I I O O SDIO data line 2 SDIO data line 3 SDIO command line SDIO clock line SDIO data line 0 SDIO data line 1 Ground connections Internal Buck voltage generation pin I/O Voltage supply input Internal Buck voltage generation pin External Low Power Clock input (32.768KHz) PCM Data output PCM clock PCM data input PCM sync signal Floating (Dont connected to ground) Floating (Dont connected to ground) Ground connections Floating (Dont connected to ground) Ground connections Low asserting reset for Bluetooth core Floating (Dont connected to ground) Ground connections Floating (Dont connected to ground) Floating (Dont connected to ground) Floating (Dont connected to ground) Floating (Dont connected to ground) FM UART interface FM UART interface FM UART interface FM UART interface FM Analog AUDIO left output FM Analog AUDIO right output Floating (Dont connected to ground) 12 8. Dimensions 8.1 Physical Dimensions

(Unit: mm)

< TOP VIEW >

< Side View >

< TOP VIEW >

13 8.2 Layout Recommendation

(Unit: mm)

< TOP VIEW >

14 FCC warning:

The modular transmitter have its own RF shielding, but this 1mm of the hole can only ensure 6th harmonic of 2.4G and 3th harmonic of 5G not coupling theoretically. Therefore, this is a limited module. This module only use for the Lighthouse LED Video Display Screen, and the model of the Lighthouse LED Video Display Screen is A2.5-89 , A2.5-

118, A2.5-104. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. This module is designed to comply with the FCC statement, FCC ID is: 2ARRD-AP6330. The host system using this module, should have label in a visible area indicated the following texts: "Contains FCC ID: 2ARRD-AP6330".

PRODUCT LABELING Proposed FCC ID Label Format FCC ID: 2ARRD-AP6330 Specifications: Text is Black in color and justified. Labels are printed in indelible ink on permanent adhesive silk-screened onto the EUT or shall be affixed at a conspicuous location on the EUT. Proposed Label Location on EUT FCC ID Label Location TRF NO. FCC15/A Page 1 of 1 Report No.: ES180831014W Ver.1.0

RF_160, Issue 03 Declaration of Authorization We Name:

Address:

Lighthouse Technologies Limited FLAT/RM 608 6/F PHOTONICS CTR 2 SCIENCE PARK EAST AVENUE HONG KONG SCIENCE PART SHATIN NT City:

HONG KONG Country:

China Declare that:

Name Representative of agent:

Agent Company name:

Address:

City:

Country Lisa Wang(1) EMTEK (SHENZHEN) CO., LTD. Bldg 69, Majialong Industry Zone, Nanshan District, Shenzhen China is authorized to apply for Certification of the following product(s):

Product description: WIFI Module Type designation: AP6330 Trademark:

AMPAK FCC ID:

2ARRD-AP6330 on our behalf. Date:

2018-11-23 Name:

Zhihong Li Function:

engineer Signature:

Notes:

(1): Required for FCC application

(2): For FCC it must be the Grantee Code owner or the authorized agent.

RF_734_02 04 April 16 Modular Approval Request FCC (KDB 996369 D01 & Part 15.212) FCC ID: 2ARRD-AP6330 Items to be covered by Single modular transmitters. 1. The modular transmitter must have its own RF shielding. 6. The modular transmitter must be equipped with either a permanently affixed label or must be capable of electronically displaying its FCC identification number in accordance with 15.212 (a)(1)(vi)(A) / (B). YES The modular have one permanently affixed label Answer from applicant NO The modular transmitter have its own RF shielding, but this 1mm of the hole can only ensure 6th harmonic of 2.4G and 3th harmonic of 5G not coupling theoretically YES The modular accord with Part 15 requirements YES The modular It has its own power supply regulation YES The modular accord with the antenna requirements of Section 15.203 and 15.204(b)(c) YES The modular accord Part 15 emission limits YES The modular transmitter accord with any specific rule or operating requirements YES The modular transmitter accord RF exposure requirements 2. The modular transmitter must have buffered modulation/data inputs (if such inputs are provided) to ensure that the module will comply with Part 15 requirements under conditions of excessive data rates or over-modulation. 3. The modular transmitter must have its own power supply regulation. 4. The modular transmitter must comply with the antenna requirements of Section 15.203 and 15.204(b)(c). The antenna must either be permanently attached or employ a unique antenna coupler (at all connections between the module and the antenna, including the cable). 5. The modular transmitter must be tested in a stand-alone configuration, i.e., the module must not be inside another device during testing. This is intended to demonstrate that the module is capable of complying with Part 15 emission limits regardless of the device into which it is eventually installed. 8. there are very strict operational and 7. The modular transmitter must comply with any specific rule or operating requirements applicable to the transmitter and the manufacturer must provide adequate instructions along with the module to explain any such requirements. A copy of these instructions must be included in the application for equipment authorization. For example, timing requirements that must be met before a transmitter is authorized for operation under Section 15.231. For instance, data transmission is prohibited, except for operation under Section 15.231(e), in which case there are separate field strength level and timing requirements. Compliance with these requirements must be assured. The modular transmitter must comply with any applicable RF exposure requirements. For example, FCC Rules in Sections 1.1310, 2.1091, 2.1093, and specific Sections of Part 15, including 15.319(i), 15.407(f), 15.253(f) and 15.255(g), require that Unlicensed PCS, UNII and millimeter wave devices perform routine environmental evaluation for RF Exposure to demonstrate compliance. In addition, spread spectrum transmitters operating under Section 15.247 are required to address RF Exposure compliance. Modular transmitters approved under other Sections of Part 15, when necessary, may also need to address certain RF Exposure concerns, typically by providing specific installation and operating instructions for users, installers and other interested parties to ensure compliance. RF_734_02 04 April 16 Answer from applicant Items to be covered by Split modular transmitters. 1. The modular transmitter must comply with all requirements of a single modular transmitter except for items (1) & (5) of the above single modular approval requirements. 2. Only the radio front end must be shielded. The physical crystal and tuning capacitors may be located external to the shielded radio elements. The interface between the split sections of the modular system must be digital with a minimum signalling amplitude of 150 mV peak-to-peak. 3. Control information and other data may be exchanged between the transmitter control elements and radio front end. 4. The sections of a split modular transmitter must be tested installed in a host device(s) similar to that which is representative of the platform(s) intended for use. 5. Manufacturers must ensure that only transmitter control elements and radio front end components that have been approved together are capable of operating together. The transmitter module must not operate unless it has verified that the installed transmitter control elements and radio front end have been authorized together. Manufacturers may use means including, but not limited to, coding in hardware and electronic signatures in software to meet these requirements, and must describe the methods in their application for equipment authorization. Note: A limited modular approval (LMA) may be granted for single or split modular transmitters that comply partially with the requirements above. Name and surname of applicant (or authorized representative): Zhihong Li Date: ___2018-11-22_ Signature:

WIFI Channel 12 and 13 Declaration Letter Lighthouse Technologies Limited WIFI Channel 12 and 13 Declaration Letter We declare the equipment identified below with regards to Channel 12 and 13 capabilities for FCC ID: 2ARRD-AP6330 Declaration Product hardware does not have the capability to operate on Channel 12 and 13. Product hardware has the capability to operate on Channel 12 and 13. However, these two channels will be disabled via software and will not be accessible to user. Product hardware has the capability to operate on Channel 12 and 13. However, all the operated channels cant be changed in the RF parameter via software. All channels have complied with all of the requirements sets out in FCC Part 15.247. Product hardware has the capability to operate on WiFi Channel 12 and 13, and meets the requirements of KDB 594280 D01 v02r01. Please note:

1.) By default, this device operates in a mode that is compliant with the U.S. requirements. 2.) This device will also use supplemental information such as geo-location data to determine that it is operating outside the U.S., if necessary, to change its power. Such supplemental data will be derived from the following:

Global Navigation Satellite System (GNSS)7 sensors in the device Mobile Country Code (MCC),8 or MCC with a Mobile Network code (MNC), received from a CMRS9 carrier and received directly by a receiver on the device Country information derived from multiple adjacent access points (for example using IEEE Std 802.11d provisions) may be permitted on case-by-case basis SCS-F190 WiFi Channel 12&13 Declaration Letter Page 1 of 2 Rev.1.0 Created by William Graff Approved by Bao-Thuong Nguyen Other suitable geo-location data based on IP addresses or other reliable source. Name / Title: Zhihong Li/Engineer Signature:

Phone: +86 0752-8468054 Email: lizhihong@lighthousetech.com Date:2018-11-23 SCS-F190 WiFi Channel 12&13 Declaration Letter Page 2 of 2 Rev.1.0 Created by William Graff Approved by Bao-Thuong Nguyen

FCC, Request for non-disclosure RF_501, Issue 6 Date: 16-Jul-10 Page 1 of 1 Company Name: Lighthouse Technologies Limited Address:

FLAT/RM 608 6/F PHOTONICS CTR 2 SCIENCE PARK EAST AVENUE HONG KONG SCIENCE PART SHATIN NT City:

Country:

HONG KONG China To: Telefication B.V., Dept. FCC TCB Edisonstraat 12A 6902 PK ZEVENAAR The Netherlands Subject: Request for confidentiality FCC ID: 2ARRD-AP6330 Reference number: ######

Dear FCC TCB, 1. Long-Term Confidentiality Pursuant to 47 CFR Section 0.459(a) & (b), we hereby requests non-disclosure and confidential treatment of the following materials submitted in support of FCC certification application:

Bill(s) of Material Block Diagrams Operational Description Schematic Diagrams Tune-up Procedure Above materials contain secrets, proprietary and technical information, which would customarily be guarded from competitors under 47 CFR, section 0.457(d)(2). Disclosure or publication or any portion of this company confidential material to other parties could cause substantial competitive harm and provide unjustified benefits for competitors. 2. Short-Term Confidentiality (STC) Pursuant to Public Notice DA 04-1705 of the Commissions policy, in order to comply with the marketing regulations in 47 CFR 2.803 and the importation rules in 47 CFR 2.1204, applicant hereby requests Short-Term Confidential treatment of the following materials (note 1):

Internal Photos Users Manual Test Set-up Photos External Photos Justification:

Planned Release Date STC:

(notes 2, 3, 4, 5) Date: 2018-11-23 Name and signature of applicant: Zhihong Li/Engineer Notes:

1) A document or type of document can only have ONE type of confidentiality!

2) Short-Term confidentiality is in principle for 45 days from date of grant; it can be extended max 3 times (total time 180 days max.)!

3) FCC must be informed when marketing begins earlier. 4) Release takes place automatically thus extension must be requested in time. Telefication does not remind you of this!

5) Request for extension or for release must be received by Telefication at least 7 days before date of actual marketing or before expiration of the STC period