all | frequencies |
|
exhibits | applications |
---|---|---|---|---|
manual |
app s | submitted / available | |||||||
---|---|---|---|---|---|---|---|---|
1 |
|
Manual | Users Manual | 2.29 MiB | ||||
1 | Cover Letter(s) | |||||||
1 | Cover Letter(s) | |||||||
1 | External Photos | |||||||
1 | Internal Photos | |||||||
1 | ID Label/Location Info | |||||||
1 | ID Label/Location Info | |||||||
1 | Operational Description | |||||||
1 | RF Exposure Info | |||||||
1 | Test Report | |||||||
1 | Test Setup Photos |
1 | Manual | Users Manual | 2.29 MiB |
A Division of Cisco Systems, Inc. 2.4802.11g GHz WIRELESS Compact Wireless-G Internet Video Camera User Guide Model No. WVC54GC Compact Wireless-G Internet Video Camera Copyright and Trademarks Specifications are subject to change without notice. Linksys is a registered trademark or trademark of Cisco Systems, Inc. and/or its affiliates in the U.S. and certain other countries. Copyright 2005 Cisco Systems, Inc. All rights reserved. Other brands and product names are trademarks or registered trademarks of their respective holders. This product contains chemicals, including lead, known WARNING:
to the State of California to cause cancer, and birth defects or other reproductive harm. Wash hands after handling. How to Use this User Guide The user guide to the Compact Wireless-G Internet Video Camera has been designed to make understanding networking with the Access Point easier than ever. Look for the following items when reading this User Guide:
This checkmark means there is a note of interest and is something you should pay special attention to while using the Camera. This exclamation point means there is a caution or warning and is something that could damage your property or the Camera. This question mark provides you with a reminder about something you might need to do while using the Camera. In addition to these symbols, there are definitions for technical terms that are presented like this:
word: definition. Also, each figure (diagram, screenshot, or other image) is provided with a figure number and description, like this:
Figure 0-1: Sample Figure Description Figure numbers and descriptions can also be found in the List of Figures section. WVC54GC-UG-50907A JL Compact Wireless-G Internet Video Camera Table of Contents Chapter 1: Introduction Welcome Whats in this Guide?
Chapter 2: Planning Your Wireless Network Introduction Ad-Hoc and Infrastructure Modes Network Layout Chapter 3: Getting to Know the Compact Wireless-G Internet Video Camera Camera LED Camera Head Camera Reset Button Camera Ports Camera Stand Chapter 4: Connecting the Compact Wireless-G Internet Video Camera for Setup Overview Connection to a Wired Network for Setup Moving the Camera to a Different Network Chapter 5: Setting up and Mounting the Compact Wireless-G Internet Video Camera Setup Wizard Placement Options Chapter 6: Installing and Using the Compact Wireless-G Internet Video Camera Multi-Camera Viewer & Recorder Utility Overview Installing the Multi-Camera Viewer & Recorder Utility Using the Multi-Camera Viewer & Recorder Utility Chapter 7: Setting up the Linksys SoloLink DDNS Service Overview Introduction 1 1 2 4 4 4 4 6 6 6 6 7 7 8 8 8 9 10 10 19 21 21 21 23 33 33 33 Compact Wireless-G Internet Video Camera Setup Wizard for the SoloLink DDNS Service SoloLink Registration of Additional Cameras Chapter 8: Using the Compact Wireless-G Internet Video Cameras Web-based Utility Overview How to Access the Web-based Utility View Video Setup Help Appendix A: Troubleshooting Common Problems and Solutions Frequently Asked Questions Appendix B: Wireless Security Security Precautions Security Threats Facing Wireless Networks Appendix C: Upgrading Firmware Appendix D: Windows Help Appendix E: Glossary Appendix F: Specifications Appendix G: Warranty Information Appendix H: Regulatory Information Appendix I: Contact Information 33 43 45 45 45 46 47 60 61 61 63 66 66 66 69 70 71 77 79 80 84 Compact Wireless-G Internet Video Camera List of Figures Figure 3-1: Camera LED Figure 3-2: Camera Tilting Feature Figure 3-3: Reset Button Figure 3-4: Camera in Standing Position Figure 3-5: Camera in Wall-Mounting Position Figure 4-1: Connect the Ethernet Network Cable Figure 4-2: Connect the Power Adapter Figure 5-1: Setup Wizard - Welcome Screen Figure 5-2: End User License Agreement Screen Figure 5-3: Connect the Network Cable to the Router or Switch Screen Figure 5-4: Connect the Network Cable to the Camera Screen Figure 5-5: Power on the Camera Screen Figure 5-6: Check the LED Screen Figure 5-7: Cameras Found Screen Figure 5-8: Login Screen Figure 5-9: Basic Settings Screen Figure 5-10: Network Settings Screen Figure 5-11: IP Settings Screen Figure 5-12: Mode Settings Screen Figure 5-13: Wireless Settings Screen Figure 5-14: Security Settings - WPA-Personal Screen Figure 5-15: Security Settings - WEP (64-Bit) Screen Figure 5-16: Review New Settings Screen Figure 5-17: Confirm New Settings Screen Figure 5-18: Congratulations Screen Figure 5-19: Stand Option Figure 5-20: Camera in Standing Position Figure 5-21: Wall Mount Option 6 6 6 7 7 8 8 10 10 11 11 12 12 13 13 13 14 14 15 15 16 16 17 17 18 19 19 20 Compact Wireless-G Internet Video Camera Figure 5-22: Camera in Wall-Mounting Position Figure 5-23: Wall-Mount Slots Figure 6-1: Install Viewer & Recorder Utility Screen Figure 6-2: Install Viewer & Recorder Utility - Welcome Screen Figure 6-3: Choose Destination Location Screen Figure 6-4: Ready to Install the Program Screen Figure 6-5: InstallShield Wizard Complete Screen Figure 6-6: Multi-Camera Viewer & Recorder Utility Icon Figure 6-7: Main Screen Figure 6-8: Add Camera - LAN Screen Figure 6-9: Add Camera - Internet Screen Figure 6-10: View Video Screen Figure 6-11: Delete Camera Screen Figure 6-12: Change Settings Screen Figure 6-13: Scheduled Recordings Screen Figure 6-14: Files Screen Figure 6-15: Recorded Files Screen Figure 6-16: Motion Detection Files Screen Figure 6-17: Window Showing SnapShot Folders Figure 6-18: Motion Detection Settings Screen Figure 6-19: Utility Settings Screen Figure 7-1: SoloLink Service Figure 7-2: SoloLink Welcome Screen Figure 7-3: SoloLink for Dynamic IP Address Screen Figure 7-4: SoloLink for Convenience Screen Figure 7-5: Check Connections Screen Figure 7-6: Cameras Found Screen Figure 7-7: Login Screen Figure 7-8: SoloLink DDNS Screen Figure 7-9: Confirm Active Internet Connection Screen 20 20 21 21 22 22 22 23 23 24 25 26 27 27 28 29 29 29 30 30 31 33 33 34 34 35 35 36 36 37 Compact Wireless-G Internet Video Camera Figure 7-10: Welcome to the SoloLink DDNS Service Screen Figure 7-11: Sign Up Screen Figure 7-12: Confirmation of New Settings Screen Figure 7-13: Select a Location ID Screen Figure 7-14: Confirm Your Location ID Screen Figure 7-15: Payment Screen Figure 7-16: Verification Screen Figure 7-17: Create Links Screen Figure 7-18: Successful Registration Screen Figure 7-19: Account Confirmation of Camera Screen Figure 7-20: Successful Setup Screen Figure 7-21: Port Forwarding Information Figure 7-22: Web-based Utility Welcome Figure 7-23: Web Utility Login Screen Figure 7-24: SoloLink DDNS Screen Figure 7-25: Find Available Port Screen Figure 8-1: Cameras Default IP Address Figure 8-2: Web-based Utility Welcome Figure 8-3: Security Warning Screen Figure 8-4: View Video Screen Figure 8-5: Web Utility Login Screen Figure 8-6: Basic Screen Figure 8-7: Basic - Device Settings Screen Figure 8-8: Basic - LAN and Wireless Settings Screen Figure 8-9: Wireless Security - WPA Personal Screen Figure 8-10: Wireless Security - WEP Screen Figure 8-11: Image Screen Figure 8-12: Administrator Screen Figure 8-13: Upgrade Firmware Screen Figure 8-14: Users Screen 37 38 39 39 40 40 40 41 41 42 42 43 43 43 44 44 45 45 46 46 47 47 48 48 49 49 50 52 52 53 Compact Wireless-G Internet Video Camera Figure 8-15: SoloLink DDNS Screen Figure 8-16: New User Registration Screen Figure 8-17: Password Request Screen Figure 8-18: SoloLink Screen, continued Figure 8-19: Manage Your SoloLink DDNS Account Figure 8-20: Device Removal Screen Figure 8-21: Find Available Port Screen Figure 8-22: Options Screen Figure 8-23: Options Screen, continued Figure 8-24: Motion Detection Screen Figure 8-25: Status Screen Figure 8-26: User Help Screen Figure 8-27: Administrator Help Screen Figure C-1: Upgrade Firmware Screen 54 54 54 55 55 55 56 57 57 57 59 60 60 69 Compact Wireless-G Internet Video Camera Chapter 1: Introduction Welcome Thank you for choosing the Linksys Compact Wireless-G Internet Video Camera. This Camera sends live video through the Internet to a web browser anywhere in the world! This compact, self-contained unit lets you keep an eye on your home, your kids, your workplacewhatevers important to you. How does the Camera do all of this? Unlike standard web cams that require an attached PC, the Internet Video Camera contains its own web server, so it can connect directly to a network, either over Wireless-G (802.11b) networking, or over 10/100 Ethernet cable. The advanced MPEG-4 video compression produces a high-quality, high-framerate, up to 320 x 240 audio/video stream. The Internet Video Cameras unique form-factor and wireless connectivity allows you to mount it on a wall nearly anywhere, or slip it into its included stand for desktop use. Once its connected to your home network, you can see what it sees from any PC in the house, while the audio/video stream is secured from the outside world, hidden behind your Router. If you want the video to be visible from outside your home network, you can open an appropriate port on the Router, and then create password-protected accounts to manage access to the Camera, or leave it wide open for the world to see. The SoloLink DDNS Service (trial sign-up included) lets you access your Camera using an easy-to-remember name, even if your home Internet connection uses a dynamic IP address. You can also turn on Security Mode, which tells the Camera to send you an e-mail message with a short video attached to up to three e-mail addresses whenever it detects motion in its field of view. You can then log onto the live video stream if the situation warrants. The included Multi-Camera Viewer & Recorder Utility lets you record the video stream to your local hard drive, live or on a predetermined schedule. Use the instructions in this Guide to help you integrate the Camera into your network. These instructions should be all you need to get the most out of the Compact Wireless-G Internet Video Camera. 802.11g: An IEEE wireless networking standard that specifies a maximum data transfer rate of 54Mbps, an operating frequency of 2.4GHz, and backward compatibility with 802.11b devices. Ethernet: an IEEE standard network protocol that specifies how data is placed on and retrieved from a common transmission medium. Chapter 1: Introduction Welcome 1 Compact Wireless-G Internet Video Camera Whats in this Guide?
This user guide covers the steps for setting up and using the Compact Wireless-G Internet Video Camera.
Chapter 1: Introduction This chapter describes the Cameras applications and this User Guide.
Chapter 2: Planning Your Wireless Network This chapter discusses a few of the basics about wireless networking.
Chapter 3: Getting to Know the Compact Wireless-G Internet Video Camera This chapter describes the physical features of the Camera.
Chapter 4: Connecting the Compact Wireless-G Internet Video Camera This chapter instructs you on how to connect the Camera to your network before you run the Setup Wizard.
Chapter 5: Setting up and Mounting the Compact Wireless-G Internet Video Camera This chapter instructs you on how to use the Setup Wizard for setup and configuration of the Camera, as well as how to mount the Camera.
Chapter 6: Installing and Using the Compact Wireless-G Internet Video Camera Utility This chapter explains how to install and use the Compact Wireless-G Internet Video Camera Utility on your PC, so you can view and record video.
Chapter 7: Setting up the Linksys SoloLink DDNS Service This chapter discusses the advantages of the SoloLink DDNS Service and walks you through the setup procedure.
Chapter 8: Using the Compact Wireless-G Internet Video Camera Web-based Utility This chapter describes the Web-based Utility and the features available, so you can use and alter advanced configuration settings.
Appendix A: Troubleshooting This appendix describes some problems and solutions, as well as frequently asked questions, regarding installation and use of the Camera.
Appendix B: Wireless Security This appendix discusses security issues regarding wireless networking and measures you can take to help protect your wireless network. Chapter 1: Introduction Whats in this Guide?
2 Compact Wireless-G Internet Video Camera
Appendix C: Upgrading Firmware This appendix explains how you can upgrade the Cameras firmware.
Appendix D: Windows Help This appendix describes how you can use Windows Help for instructions about networking, such as installing the TCP/IP protocol.
Appendix E: Glossary This appendix gives a brief glossary of terms frequently used in networking.
Appendix F: Specifications This appendix provides the technical specifications for the Camera.
Appendix G: Warranty Information This appendix supplies the warranty information for the Camera.
Appendix H: Regulatory Information This appendix supplies the regulatory information regarding the Camera.
Appendix I: Contact Information This appendix provides contact information for a variety of Linksys resources, including Technical Support. Chapter 1: Introduction Whats in this Guide?
3 Compact Wireless-G Internet Video Camera Chapter 2: Planning Your Wireless Network Introduction A wireless local area network (WLAN) is exactly like a regular local area network (LAN), except that each computer in the WLAN uses a wireless device to connect to the network. Computers and other devices, such as peripherals, in a WLAN share the same frequency channel and SSID, which is an identification name for wireless devices. Ad-Hoc and Infrastructure Modes Unlike wired networks, wireless networks have two different modes in which they may be set up: infrastructure and ad-hoc. An infrastructure configuration is a WLAN and wired LAN communicating to each other through an access point. An ad-hoc configuration is wireless-equipped computers communicating directly with each other. Choosing between these two modes depends on whether or not the wireless network needs to share data or peripherals with a wired network or not. If the computers on the wireless network need to be accessed by a wired network or need to share a peripheral, such as a printer, with the wired network computers, the wireless network should be set up in infrastructure mode. The basis of infrastructure mode centers around an access point, which serves as the main point of communications in a wireless network. (A wireless router can also be used because a wireless router incorporates the capabilities of an access point.) Access points transmit data to PCs equipped with wireless network cards, which can roam within a certain radial range of the access point. Multiple access points can be arranged to work in succession to extend the roaming range, and can be set up to communicate with your Ethernet (wired) hardware as well. If the wireless network is relatively small and needs to share resources only with the other computers on the wireless network, then the ad-hoc mode can be used. Ad-hoc mode allows computers equipped with wireless transmitters and receivers to communicate directly with each other, eliminating the need for an access point. The drawback of this mode is that, in Ad-Hoc mode, wireless-equipped computers are not able to communicate with computers on a wired network. And, of course, communication between the wireless-equipped computers is limited by the distance and interference directly between them. Network Layout The Compact Wireless-G Internet Video Camera is compatible with all 802.11b and 802.11g routers, as well as access points. The Camera will also communicate with network adapters, such as the Wireless-B and Wireless-G LAN (Local Area Network): the computers and networking products that make up the network in your home or office. WLAN (Wireless Local Area Network): A group of computers and associated devices that communicate with each other wirelessly. Infrastructure: configuration in which a wireless network is bridged to a wired network via an access point. Ad-hoc: a group of wireless devices communicating directly to each other
(peer-to-peer) without the use of an access point. Chapter 2: Planning Your Wireless Network Introduction 4 Compact Wireless-G Internet Video Camera Notebook Adapters for your laptop computers, Wireless-B and Wireless-G PCI Adapters for your desktop PCs, and Wireless-B and Wireless-G USB Adapters for your computers when you want to enjoy USB connectivity. With these, and many other Linksys products, your networking options are limitless. Go to the Linksys website at www.linksys.com for more information about products that work with the Compact Wireless-G Internet Video Camera. Chapter 2: Planning Your Wireless Network Network Layout 5 Compact Wireless-G Internet Video Camera Chapter 3: Getting to Know the Compact Wireless-G Internet Video Camera Camera LED The Camera has one LEDs to let you know how the Camera is functioning.
(power) Blue. The LED lights up when the Camera is powered on. It flashes while the Camera is booting up and is solidly lit when the Camera is ready for use. LED Camera Head The Camera head can be attached to its stand either on its bottom panel or its back panel. After the Camera has been assembled, you can tilt the Camera head from its ball joint. Figure 3-1: Camera LED Camera Reset Button The Camera features a Reset button on its bottom panel. RESET The RESET button is what you will press if you need to reset the Camera. Insert a paper clip into the opening. Then press the button and hold it in for five seconds. IMPORTANT: Resetting the Camera will erase all of your settings, such as encryption information, and replace them with the factory defaults. Do not reset the Camera if you want to retain these settings. NOTE: These are the factory default settings of the Camera. default IP address: 192.168.1.115 user name: admin password: admin Hole for Attaching Stand
(Stand Option) Chapter 3: Getting to Know the Compact Wireless-G Internet Video Camera Camera LED Figure 3-2: Camera Tilting Feature Figure 3-3: Reset Button RESET Button 6 Compact Wireless-G Internet Video Camera Camera Ports The Camera features two ports on its back panel. POWER The POWER port is where you will connect the power adapter. ETHERNET The ETHERNET port is where you will connect the Ethernet network cable. Camera Stand The Camera can stand on a surface or be mounted on a wall. Depending on the positioning you want, you can attach the Camera head to its stand at two different points. Hole for Attaching Stand (Wall-Mount Option) Thumbscrew If you want to stand the Camera on a surface, insert the screw end of the stand into the hole on the bottom panel. Tighten the screw end and then the gray thumbscrew. If you want to mount the Camera on a wall, insert the screw end of the stand into the hole on the back panel. Tighten the screw end, and then tighten the gray thumbscrew. Refer to Chapter 5: Setting Up and Mounting the Compact Wireless-G Internet Video Camera for further instructions about mounting the Camera on a wall. Figure 3-4: Camera in Standing Position Figure 3-5: Camera in Wall-Mounting Position Chapter 3: Getting to Know the Compact Wireless-G Internet Video Camera Camera Ports 7 Compact Wireless-G Internet Video Camera Chapter 4: Connecting the Compact Wireless-G Internet Video Camera for Setup Overview Before you set up the Camera, connect it to your wired network. If you need to move the Camera from a wired network to a wireless network, or vice versa, go to this section, Moving the Camera to a Different Network. Connection to a Wired Network for Setup 1. Connect the Ethernet network cable to your router, switch, or computer. 2. Connect the other end of the cable to the Ethernet port on the Camera. 3. Connect the power adapter to the Power port on the Camera. 4. Plug the power adapter into an electrical outlet. The Cameras power LED flashes while the Camera is initializing. The Camera is ready for use when the LED is solidly lit. Proceed to Chapter 5: Setting up and Mounting the Compact Wireless-G Internet Video Camera. Figure 4-1: Connect the Ethernet Network Cable NOTE: You MUST connect the Camera to a PC, router, or switch using the Ethernet network cable BEFORE powering on the Camera. Otherwise, the Camera will not function. Chapter 4: Connecting the Compact Wireless-G Internet Video Camera for Setup Overview Figure 4-2: Connect the Power Adapter 8 Compact Wireless-G Internet Video Camera Moving the Camera to a Different Network When you move the Camera from a wired network to a wireless network, or vice versa, you must power off the Camera before connecting to the new network. Proceed to the appropriate instructions. To move the Camera from a wired network to a wireless network, follow these instructions:
1. Unplug the power adapter from the Camera. 2. Unplug the Ethernet network cable from the Camera. 3. Re-connect the power adapter to the Power port on the Camera. The Cameras power LED flashes while the Camera is initializing. The Camera is ready for use when the LED is solidly lit. Proceed to Chapter 5: Setting up and Mounting the Compact Wireless-G Internet Video Camera. To move the Camera from a wireless network to a wired network, follow these instructions:
1. Unplug the power adapter from the Camera. 2. Connect the Ethernet network cable to your PC, router, or switch. 3. Connect the other end of the cable to the Ethernet port on the Camera. 4. Re-connect the power adapter to the Power port on the Camera. The Cameras power LED flashes while the Camera is initializing. The Camera is ready for use when the LED is solidly lit. Proceed to Chapter 5: Setting up and Mounting the Compact Wireless-G Internet Video Camera. Chapter 4: Connecting the Compact Wireless-G Internet Video Camera for Setup Moving the Camera to a Different Network 9 Compact Wireless-G Internet Video Camera Chapter 5: Setting up and Mounting the Compact Wireless-G Internet Video Camera Setup Wizard The Compact Wireless-G Internet Video Camera Setup Wizard will guide you through the installation and configuration procedure. 1. Insert the Setup CD-ROM into your CD-ROM drive. The Setup Wizard should run automatically, and the Welcome screen should appear. If it does not, click the Start button and choose Run. In the field provided, enter D:\wvc54gc.exe (if D is the letter of your CD-ROM drive). Setup. Click the Setup button to begin the installation process. Install Viewer & Recorder Utility. To install the Cameras Multi-Camera Viewer & Recorder Utility on your PC, click this button. Setup SoloLink DDNS Service. Click the Setup SoloLink DDNS Service button to configure and use Linksyss Dynamic Domain Name System (DDNS) service. Figure 5-1: Setup Wizard - Welcome Screen User Guide. Click this button to open the PDF file of this User Guide. Exit. Click the Exit button to exit the Setup Wizard. 2. To install the Camera, click the Setup button on the Welcome screen. 3. After reading the License Agreement, click Next if you agree and want to continue the installation, or click Cancel to end the installation. Chapter 5: Setting up and Mounting the Compact Wireless-G Internet Video Camera Setup Wizard Figure 5-2: End User License Agreement Screen 10 Compact Wireless-G Internet Video Camera 4. Connect the included network cable to your network router or switch. Click the Next button. 5. Connect the other end of the network cable to the Cameras ETHERNET port. Click the Next button. Figure 5-3: Connect the Network Cable to the Router or Switch Screen Chapter 5: Setting up and Mounting the Compact Wireless-G Internet Video Camera Setup Wizard 11 Figure 5-4: Connect the Network Cable to the Camera Screen Compact Wireless-G Internet Video Camera 6. Plug the included power adapter into the Cameras Power port. Plug the other end into an electrical outlet. Click the Next button. 7. Make sure the LED is lit on the Cameras front panel. If it is not lit, make sure the cables are properly connected to the Camera. Click the Next button. Figure 5-5: Power on the Camera Screen Figure 5-6: Check the LED Screen Chapter 5: Setting up and Mounting the Compact Wireless-G Internet Video Camera Setup Wizard 12 Compact Wireless-G Internet Video Camera 8. The screen displays a list of Compact Wireless-G Internet Video Cameras on your network, along with the status information for the Camera whose name is highlighted. If the Camera you want is not displayed, click the Search Again button to run a new search for Cameras. In the Selection box, click the name of the Camera you are currently installing. Write down the IP address of the Camera, so you can use it to access the Web-
based Utility later. Click the Next button. 9. For security purposes, you will be asked to enter a name and password in order to have administrator access to the Camera. In lowercase letters, enter admin in the Administrator Name and Administrator Password fields (later you can change these through the Web-based Utility). Then click the OK button. Figure 5-7: Cameras Found Screen 10. On the Basic Settings screen, you can alter the following settings:
Figure 5-8: Login Screen Camera Name. You can give the Camera a unique name. Memorable names are helpful, especially if you are using multiple Cameras on the same network. It should have 15 characters or fewer. Description. You may enter additional information, such as location, in this field. It has a maximum length of 32 characters. Time Zone. Select the time zone for the Cameras location. Date. Enter todays date in the fields provided. Time. Enter the current time in the fields provided. When you have finished making your changes, click the Next button. Chapter 5: Setting up and Mounting the Compact Wireless-G Internet Video Camera Setup Wizard Figure 5-9: Basic Settings Screen 13 Compact Wireless-G Internet Video Camera 11. The Network Settings screen will appear. Select the setting appropriate for your network. Automatic Configuration-DHCP. If your network has a DHCP server, such as a router with DHCP enabled, click the Automatic Configuration-DHCP radio button. Static IP address. If you need to assign a static IP address to the Camera, keep the default setting, Static IP address. Then click the Next button. 12. If you selected Automatic Configuration-DHCP in step 12, then proceed to step 14. If you selected Static IP Address, then the IP Settings screen will appear. Enter an IP Address, Subnet Mask, and Default Gateway appropriate for your network. You must specify an IP Address and Subnet Mask on this screen. If you are unsure about the Default Gateway, it is better to leave this field blank. Then complete the Primary DNS and/or Secondary DNS fields. Click the Next button. IP Address. Enter the IP Address of the Camera. Subnet Mask. Enter the Subnet Mask of the Camera. Default Gateway. Enter the IP address of the Default Gateway. If you are not sure, leave this field blank. Primary and Secondary DNS. Enter the IP address of your primary and secondary DNS server. You must enter at least one DNS address, which can be obtained from your ISP. When you have finished making your changes, click the Next button. Figure 5-10: Network Settings Screen Figure 5-11: IP Settings Screen Chapter 5: Setting up and Mounting the Compact Wireless-G Internet Video Camera Setup Wizard 14 Compact Wireless-G Internet Video Camera 13. The Mode Setting screen will appear. Select the appropriate mode for your network. Infrastructure. Click the Infrastructure radio button if you want the Camera to communicate using an access point or wireless router. Ad-Hoc. Click the Ad-Hoc radio button if you want the Camera to communicate without using an access point or wireless router. Click the Next button. 14. The Wireless Settings screen will appear, so you can change the wireless settings. Enter your wireless networks SSID or network name. If you chose Ad-Hoc mode, select the channel at which the network broadcasts its wireless signal. SSID. The SSID must be identical for all devices in a wireless network. It is case-sensitive and should have 32 alphanumeric characters or fewer. (You can use any keyboard character, but do not use any spaces.) Channel. If you set the Camera to Ad-Hoc mode, select the appropriate channel from the drop-down menu. All devices in your wireless ad-hoc network must use the same channel in order to function correctly. Then click the Next button. Figure 5-12: Mode Settings Screen Figure 5-13: Wireless Settings Screen Chapter 5: Setting up and Mounting the Compact Wireless-G Internet Video Camera Setup Wizard 15 Compact Wireless-G Internet Video Camera 15. Configure the wireless security settings. Select the method your network is using, WPA-Personal, WEP (128-
Bit), or WEP (64-Bit). Then proceed to the appropriate instructions. If you are not using wireless security, select Disabled, and proceed to step 10. WPA-Personal WPA-Personal automatically uses TKIP with dynamic encryption keys. Enter a passphrase on this screen. Encryption - TKIP is automatically selected as the encryption method. Passphrase - Enter a Passphrase, also called a pre-shared key, of 8-63 characters in the Passphrase field. The longer and more complex your Passphrase is, the more secure your network will be. Click Next to proceed, or click Back to return to the previous screen. WEP (128-Bit) or WEP (64-Bit) Enter a passphrase in the Passphrase field and click Next. If you want to manually enter a WEP key, leave the Passphrase field blank, and enter the WEP key in the Key 1 field. Then click Next. Passphrase - Enter a passphrase in the Passphrase field, so a WEP key is automatically generated. The passphrase is case-sensitive and should not be longer than 16 alphanumeric characters. It must match the passphrase of your other wireless network devices and is compatible with Linksys wireless products only. (If you have any non-Linksys wireless products, enter the WEP key manually on those products.) Key 1 - The WEP key you enter must match the WEP key of your wireless network. For 64-bit WEP encryption, enter exactly 10 hexadecimal characters. For 128-bit WEP encryption, enter exactly 26 hexadecimal characters. Valid hexadecimal characters are 0 to 9 and A to F. Click Next to proceed, or click Back to return to the previous screen. Figure 5-14: Security Settings - WPA-Personal Screen Chapter 5: Setting up and Mounting the Compact Wireless-G Internet Video Camera Setup Wizard 16 Figure 5-15: Security Settings - WEP (64-Bit) Screen Compact Wireless-G Internet Video Camera 16. Review your settings before you save your new settings. Click the Next button to continue. 17. Click OK to confirm that you want to save the new settings. If you want to cancel your changes, click Cancel. Figure 5-16: Review New Settings Screen Chapter 5: Setting up and Mounting the Compact Wireless-G Internet Video Camera Setup Wizard 17 Figure 5-17: Confirm New Settings Screen Compact Wireless-G Internet Video Camera 18. After the files have been successfully copied, the Congratulations screen will appear. Install Viewer & Recorder Utility. Click this button to install the Cameras Utility on your PC. Setup SoloLink DDNS Service. Click the Setup SoloLink DDNS Service button to set up and configure the Linksys Dynamic Domain Name System (DDNS) service. User Guide. Click this button to open the PDF file of this User Guide. Exit. Click the Exit button if you want to install the Cameras Utility later. Go to the Placement Options section. Figure 5-18: Congratulations Screen Chapter 5: Setting up and Mounting the Compact Wireless-G Internet Video Camera Setup Wizard 18 Compact Wireless-G Internet Video Camera Placement Options The Camera can stand on a surface or be mounted on a wall. Depending on the positioning you want, you can attach the Camera head to its stand at two different points. Stand Option 1. Insert the screw end of the stand into the hole on the bottom panel. 2. Tighten the screw end and then the gray thumbscrew. 3. Place the Camera, and adjust the tilt of its head accordingly. Figure 5-19: Stand Option Figure 5-20: Camera in Standing Position Chapter 5: Setting up and Mounting the Compact Wireless-G Internet Video Camera Placement Options 19 Compact Wireless-G Internet Video Camera Wall Mount Option You will use the Cameras stand to mount the Camera on a wall. Its stand has two wall-mount slots that are spaced 58 mm (2.28 inches) apart. 1. Insert the screw end of the stand into the hole on the back panel. 2. Tighten the screw end and then the gray thumbscrew. 3. Determine where you want to mount the Camera. Attach two screws to the wall, so that the Cameras wall-
mount slots line up with the two screws. Figure 5-21: Wall Mount Option 4. Maneuver the Camera so the screws are inserted into the two slots. 5. Adjust the tilt of its head accordingly. The installation of the Compact Wireless-G Internet Video Camera is complete. Go to Chapter 6:
Installing the Compact Wireless-G Internet Video Camera Multi-Camera Viewer & Recorder Utility. If advanced users wish to access the Camera through its Web-based Utility, then proceed to Chapter 8:
Using the Compact Wireless-G Internet Video Camera Web-based Utility. Figure 5-22: Camera in Wall-Mounting Position 58 mm
(2.28 inches) Chapter 5: Setting up and Mounting the Compact Wireless-G Internet Video Camera Placement Options Figure 5-23: Wall-Mount Slots 20 Compact Wireless-G Internet Video Camera Chapter 6: Installing and Using the Compact Wireless-G Internet Video Camera Multi-Camera Viewer & Recorder Utility Overview This chapter will instruct you on how to install and use the Compact Wireless-G Internet Video Camera Multi-
Camera Viewer & Recorder Utility on your PC. The Utility allows you to easily view and record the Cameras video. If the Wireless-B or G Internet Video Camera Viewer & Recorder Utility has already been installed on your PC, Linksys recommends that you uninstall it before you install the Compact Wireless-G Internet Video Camera Multi-
Camera Viewer & Recorder Utility (this Utility will also work with Wireless-B or G Internet Video Cameras). NOTE: To view video using a web browser, you must use Internet Explorer version 5.5 or higher. The View Video feature will not work with Netscape. Netscape users should use the Multi-Camera Viewer
& Recorder Utility instead. Installing the Multi-Camera Viewer & Recorder Utility 1. On the Welcome or Congratulations screen of the Setup Wizard, click the Install Viewer & Recorder Utility button. Figure 6-1: Install Viewer & Recorder Utility Screen 2. The Welcome screen will appear. Click the Next button to proceed. Chapter 6: Installing and Using the Compact Wireless-G Internet Video Camera Multi-Camera Viewer & Recorder Utility Overview Figure 6-2: Install Viewer & Recorder Utility -
Welcome Screen 21 Compact Wireless-G Internet Video Camera 3. The Choose Destination Location screen will appear. To install the Multi-Camera Viewer & Recorder Utility files in the default folder, click the Next button. To select a different folder, click the Change button and follow the on-screen directions. 4. The Ready to Install the Program screen will appear. Click the Install button to begin the installation. Figure 6-3: Choose Destination Location Screen 5. When the setup is complete, click the Finish button. To learn how to use the Multi-Camera Viewer & Recorder Utility, proceed to the next section, Using the Multi-Camera Viewer & Recorder Utility. To set up the Linksys SoloLink Service, go to Chapter 7: Setting up the Linksys SoloLink DDNS Service. Advanced users: If you want to use the Cameras Web-based Utility, go to Chapter 8: Using the Compact Wireless-G Internet Video Camera Web-based Utility. Figure 6-4: Ready to Install the Program Screen Chapter 6: Installing and Using the Compact Wireless-G Internet Video Camera Multi-Camera Viewer & Recorder Utility Installing the Multi-Camera Viewer & Recorder Utility Figure 6-5: InstallShield Wizard Complete Screen 22 Compact Wireless-G Internet Video Camera Using the Multi-Camera Viewer & Recorder Utility After the Multi-Camera Viewer & Recorder Utility has been installed, the Multi-Camera Viewer & Recorder Utility icon will be displayed in two locations, one on your desktop and one in the system tray of your desktops taskbar. NOTE: This Multi-Camera Viewer & Recorder Utility is backward-compatible with the Wireless-B Internet Video Camera, so you can use this Utility to control Wireless-G and Wireless-B Internet Video Cameras on your network. There are two ways to open the Multi-Camera Viewer & Recorder Utility:
Double-click the icon on your desktop (the icon acts as a shortcut)
Right-click the icon in the system tray, and then click Main Program. You will see the Utilitys main screen. It is divided into three sections, Camera Status, Camera functions, and viewing windows for Channels 1-8 of the Utility. (To view different windows, use the scroll bar on the right.) Camera functions include finding or deleting Cameras, changing Camera settings, scheduling recordings, accessing saved files, and configuring the motion detection settings. To configure the Utility settings, click the Utility Settings button. To get help information, click the ? button in the upper right-hand corner. To minimize the Utility, click the button in the upper right-hand corner. To exit the Utility, click the X button in the upper right-hand corner. Camera Status Figure 6-6: Multi-Camera Viewer & Recorder Utility Icon This section lists all of the Cameras the Utility has detected. To view the video of a specific Camera, select a Camera. Drag and drop the Camera to a viewing window. Figure 6-7: Main Screen CH. Displayed here is the Channel setting used by the Camera within the Utility. (The Utility offers up to eight channels.) Camera Name. This is the name you gave to the Camera. AUDIO ON/OFF. The Compact Wireless-G Internet Video Camera does not feature audio; however, other Cameras do. This displays he status of their audio transmissions. VIDEO ON/OFF. This indicates the status of the Cameras video transmissions. Chapter 6: Installing and Using the Compact Wireless-G Internet Video Camera Multi-Camera Viewer & Recorder Utility Using the Multi-Camera Viewer & Recorder Utility 23 Compact Wireless-G Internet Video Camera Add Camera To add a Camera on your local network or the Internet, click Add Camera. The Add Camera screen will appear. There will be two tabs available, LAN and Internet. LAN The LAN screen shows the Cameras found on your local area network, along with the status information for each Camera. Cameras on LAN The Utility will search for Cameras on the local area network and display a list in the Cameras on LAN box. To run a new search, click the Search button. For the Camera whose name is currently selected in the Cameras on LAN box, the following information will be displayed:
Camera Data Camera Name. This is the name you gave to the Camera. MAC Name. Displayed here is the MAC address of the Camera. Description. This is the information about the Camera that you entered. Address. Shown here is the Cameras IP address. Port Number. This is the port number the Camera uses for communication. Login. If you set up the Camera with a name and password, then you will need to enter them here in order to access the Camera. Name. Enter the login Name. Password. Enter the login Password. To add a Camera to the Utilitys list, select the Camera you wish to add by clicking its name in the Cameras on LAN box. Then click the Add button. You will be notified when the Camera has been added. Click the OK button. To close this screen, click the X button in the upper right-hand corner. Figure 6-8: Add Camera - LAN Screen Chapter 6: Installing and Using the Compact Wireless-G Internet Video Camera Multi-Camera Viewer & Recorder Utility Using the Multi-Camera Viewer & Recorder Utility 24 Compact Wireless-G Internet Video Camera Internet The Internet screen shows the Camera found on the Internet, along with the status information for it. Test Results First, go to the Camera Data section. Enter the Cameras IP Address, Port Number, and login information (if required). Then click the Connect button to find the Camera. The following information will be displayed:
Camera Data Camera Name. This is the name you gave to the Camera. MAC Name. Displayed here is the MAC address of the Camera. Description. This is the information about the Camera that you entered. Address. Shown here is the Cameras IP address or SoloLink DDNS address. Port Number. This is the port number the Camera uses for communication. Login. If you set up the Camera with a name and password, then you will need to enter them here in order to access the Camera. Name. Enter the login Name. Password. Enter the login Password. To add the Camera to the Utilitys list, click the Add button. If you wish to clear a Camera, click the Clear button. To close this screen, click the X button in the upper right-hand corner. Figure 6-9: Add Camera - Internet Screen Chapter 6: Installing and Using the Compact Wireless-G Internet Video Camera Multi-Camera Viewer & Recorder Utility Using the Multi-Camera Viewer & Recorder Utility 25 Compact Wireless-G Internet Video Camera View Video The Camera Status section lists all of the Cameras the Utility has detected. To view the video of a specific Camera, select a Camera. Drag and drop the Camera to a Channel (viewing) window. Double-click the viewing window if you want to make the viewing window larger, record, play, stop, take pictures, or zoom. (For Cameras with audio, you can also raise or lower the volume.) To close this viewing window, click the X button in the upper right-hand corner. Icon Function If you want to record the current video, click this icon. If you want to play the current video, click this icon. If you want to freeze the current frame of video or stop recording, click this icon. To take a snapshot of the current frame of video, click this icon. A digital zoom feature is available. To zoom in on a section of the window, click this icon. Then use your mouse to select the section you want to magnify. Click the icon again to disable the zoom feature. For Cameras that feature audio, click this icon to turn audio on or off.
(The Compact Wireless-G Internet Video Camera does not feature audio.) For Cameras that feature audio, click this bar and move its endpoint to raise or lower the volume. This indicates the Channel setting used by the Camera within the Utility.
(You cannot use this icon to change the Cameras Channel setting;
instead, you must return to the main menu. Drag and drop the Camera to a different viewing window with the Channel setting you want.) If you want to make the viewing window twice as large, click this icon. Figure 6-10: View Video Screen Chapter 6: Installing and Using the Compact Wireless-G Internet Video Camera Multi-Camera Viewer & Recorder Utility Using the Multi-Camera Viewer & Recorder Utility 26 Compact Wireless-G Internet Video Camera Delete Camera To delete a Camera, select its name in the Camera Status section, and click Delete Camera. When you are asked to confirm the deletion, click the OK button. Camera Settings To modify a Cameras settings, select its name in the Camera List box, and click Change Settings. Test Results Click the Test button to check the connection. The results will be displayed. If you need to change the Cameras network settings or login information, you can do so on this screen. Camera Data Camera Name. This is the name you gave to the Camera. MAC Name. Displayed here is the MAC address of the Camera. Description. This is the information about the Camera that you entered. Address. Enter the Cameras new IP address or SoloLink DDNS address. Port Number. Enter the new port number that the Camera uses for communication. Login. If you set up the Camera with a name and password, then you can change them here. Name. Enter the new login Name. Password. Enter the new login Password. Click the Save button to save the new settings. To close this screen, click the X button in the upper right-hand corner. Figure 6-11: Delete Camera Screen Figure 6-12: Change Settings Screen Chapter 6: Installing and Using the Compact Wireless-G Internet Video Camera Multi-Camera Viewer & Recorder Utility Using the Multi-Camera Viewer & Recorder Utility 27 Compact Wireless-G Internet Video Camera Scheduled Recordings To schedule recordings for a Camera, select its name in the Camera List box, and click Scheduled Recording. A list of scheduled recordings will appear. Frequency. Decide which days you want the Camera to record. Select the appropriate Frequency from the drop-
down menu. Start Time. Select the time you want the recording to begin. Duration. Select how long you want the recording to be. After you have made your selections, click the Add button to save the new scheduled recording. To delete a scheduled recording, select the recording from the list, and click the Delete button. To close this screen, click the X button in the upper right-hand corner. Figure 6-13: Scheduled Recordings Screen You may find it helpful to know how much memory is required to hold a video recording. The following table lists estimated bit rates and file sizes for a typical video recording at each available resolution and video. Estimated Hard-Drive Memory Space Required for Video Recording per Hour NOTE: In order for the scheduled recordings to occur, the Multi-Camera Viewer & Recorder Utility must be running on a networked PC. Resolution Quality Level Bit Rate File Size 320 x 240 320 x 240 320 x 240 320 x 240 320 x 240 160 x 120 160 x 120 160 x 120 160 x 120 160 x 120 Very High High Normal Low Very Low Very High High Normal Low Very Low 900kbps 500kbps 300kbps 120kbps 40kbps 800kbps 400kbps 200kbps 100kbps 40kbps 430MB 330MB 240MB 230MB 225MB 380MB 270MB 230MB 220MB 210MB NOTE: The maximum length of a recording file is one hour. If a recording is more than one hour long, then multiple files will be saved. Chapter 6: Installing and Using the Compact Wireless-G Internet Video Camera Multi-Camera Viewer & Recorder Utility Using the Multi-Camera Viewer & Recorder Utility 28 Compact Wireless-G Internet Video Camera Saved Files To access the saved files of a Camera, select its name in the Camera List box, and click Saved Files. You have three types of files available: Recorded Videos, Motion Detection Videos, and Snapshot Pictures. To close this screen, click the X button in the upper right-hand corner. Recorded Files Click the Recorded Videos button, and the Recorded Files screen will appear and display a list of files, organized by Camera Name, File Name, and Start Time. Camera Name. This is the name of the Camera that was used. File Name. Displayed here is the name of the file. If it was an instant recording, the filename format is LAN_R_(date)_(end time). If it was a scheduled recording, the filename format is LAN_(date)_(end time). Start Time. This is the time the recording began. To play a recording, select the appropriate file and click the Play button. To delete a recording, select the appropriate file and click the Delete button. If the recorded file you want is not listed, click the Explore button to find it. To rename a recorded file, click the Explore button. After you have found the file, you can rename it. To close this screen, click the X button in the upper right-hand corner. Motion Detection Files Click the Motion Detection Videos button, and the Motion Detection Files screen will appear and display a list of files, organized by Camera Name, File Name, and Start Time. (Click Motion Detection on the main menu to access the Motion Detection Settings screen). Camera Name. This is the name of the Camera that was used. File Name. Displayed here is the name of the file. Start Time. This is the time the recording began. To play a video, select the appropriate file and click the Play button. To delete a file, select the appropriate file and click the Delete button. If the file you want is not listed, click the Explore button to find it. To rename a file, click the Explore button. After you have found the file, you can rename it. To close this screen, click the X button in the upper right-hand corner. Chapter 6: Installing and Using the Compact Wireless-G Internet Video Camera Multi-Camera Viewer & Recorder Utility Using the Multi-Camera Viewer & Recorder Utility Figure 6-14: Files Screen Figure 6-15: Recorded Files Screen NOTE: Use Windows Media Player 7 or higher to view your recordings. Figure 6-16: Motion Detection Files Screen 29 Compact Wireless-G Internet Video Camera Snapshots Click the Snapshot Pictures button, and a Windows Explorer window will appear and display the available SnapShot folders. The name of each folder is the MAC address of the Camera that took that folders snapshots. Double-click a folder to see a list of its images. Motion Detection You can have video recorded when the Utility detects motion in a Cameras field of view. To configure these settings, select its name in the Camera List box, and click Motion Detection. A list of scheduled motion detection recordings will appear. Frequency. Decide which days you want the Camera to monitor its field of view for motion. Select the appropriate Frequency from the drop-down menu. Start Time. Decide what time you want the Camera to begin monitoring for motion. Select the time you want the video recording to begin. Duration. Select how long you want the Camera to monitor for motion. Sensitivity Level. You have a choice of motion sensitivity levels for the Camera. Select the appropriate level from the drop-down menu. 3 x 3 (default). By default, the Cameras field of view is split into nine sections (see the on-screen image). If you want it split into 16 sections, select 4 x 4. If you want it split into 25 sections, select 5 x 5. On the on-screen image depicting the Cameras field of view, click the sections you want monitored. The selected sections will be marked by a crisscross pattern. If you want to select all sections, click the Select All button. If you want to de-select all sections, click the Clear All button. To refresh the current image, click the Refresh Image button. After you have made your selections, click the Add button to save the new scheduled motion detection video. To delete a scheduled motion detection video, select the video from the list, and click the Delete button. To close this screen, click the X button in the upper right-hand corner. NOTE: In order for the motion detection feature and its recordings to occur, the Multi-Camera Viewer & Recorder Utility must be running on a networked PC. Figure 6-17: Window Showing SnapShot Folders Figure 6-18: Motion Detection Settings Screen NOTE: To specify the maximum length for a single motion detection video recording, click the Utility Settings button on the main menu. Chapter 6: Installing and Using the Compact Wireless-G Internet Video Camera Multi-Camera Viewer & Recorder Utility Using the Multi-Camera Viewer & Recorder Utility 30 Compact Wireless-G Internet Video Camera Utility Settings To configure the settings of the Multi-Camera Viewer & Recorder Utility, click the Utility Settings button. The Utility Settings screen will appear. You can change the Directory, Recording Time Frame, Disk Allocation for Recording, and Start Info. settings on this screen. Directory You can specify the directories where the recordings, motion detection videos, and snapshots will be saved. Recording Directory. Instant and scheduled recordings will be saved in this directory. The default is C:\Program Files\Linksys\Wireless-G Internet Video Camera\Record. Click the ... button to designate a different directory. Motion Detection Directory. Motion detection video recordings will be saved in this directory. The default is C:\Program Files\Linksys\Wireless-G Internet Video Camera\Motion. Click the ... button to designate a different directory. Snapshot Directory. Snapshots will be saved in this directory. The default is C:\Program Files\Linksys\Wireless-G Internet Video Camera\Snapshot. Click the ... button to designate a different directory. Recording Time Frame You can specify the maximum length of motion detection and instant recordings. Maximum time frame for Motion Detection Recording. This is the maximum length of time the Utility will record when motion is detected. (To configure the Motion Detection settings, click Motion Detection on the main menu.) The default is 1 min. To change the default, select the maximum length of time you want from the drop-
down menu. Maximum time frame for Instant Recording. This is the maximum length of time the Utility will record when you click the Instant Recording icon on the viewing window of a Camera. The default is 10 min. To change the default, select the maximum length of time you want from the drop-down menu. Disk Allocation for Recording You can designate how much hard disk space you want to use for recording. Total Space. This is the total amount of space available on the hard drive of the PC running this Utility. Total Space and Available Space. This is the amount of space available for recording. Chapter 6: Installing and Using the Compact Wireless-G Internet Video Camera Multi-Camera Viewer & Recorder Utility Using the Multi-Camera Viewer & Recorder Utility Figure 6-19: Utility Settings Screen 31 Compact Wireless-G Internet Video Camera Enable Disk space limit. If you want to limit the amount of disk space available for recording, click the checkbox. Enter the maximum number of megabytes in the Maximum field. Of the total amount of disk space available for recording, you can designate the amount of space available for motion detection recordings. Enter the maximum number of megabytes in the Motion Detection Recording Space field. Of the total amount of disk space available for recording, you can designate the amount of space available for instant and scheduled recordings, enter the maximum number of megabytes in the Instant/Scheduled Recording Space field. If the hard drive runs out of space, the Utility has two options. it can overwrite the oldest files or stop recording. Select the option you want, Overwrite oldest file or Stop recording. Start Info. You can designate when and how you want the Utility to launch. Launch Viewer & Recorder utility on Windows startup. If you want the Utility to launch when Windows starts up, click the checkbox. Auto start video streaming when utility starts. If you want video to automatically begin streaming when the Utility launches, click the checkbox. After you have made your changes, click the Save button to save the new settings. To cancel your changes, click the Cancel button. To close this screen, click the X button in the upper right-hand corner. To set up the Linksys SoloLink Service, go to Chapter 7: Setting up the Linksys SoloLink DDNS Service. If you want to use the Cameras Web-based Utility, go to Chapter 8: Using the Compact Wireless-G Internet Video Camera Web-based Utility. Chapter 6: Installing and Using the Compact Wireless-G Internet Video Camera Multi-Camera Viewer & Recorder Utility Using the Multi-Camera Viewer & Recorder Utility 32 Compact Wireless-G Internet Video Camera Chapter 7: Setting up the Linksys SoloLink DDNS Service Overview This chapter will briefly discuss the Linksys SoloLink DDNS Service, explain how to set up your SoloLink account, and describe how to register additional Cameras on your SoloLink account. You need only one SoloLink account. Once you have set up your account, you can register additional Cameras, one at a time, through each Cameras Web-based Utility. This way each Camera can take advantage of the SoloLink DDNS Service. Introduction The SoloLink DDNS (Dynamic Domain Name System) Service lets you assign a fixed host and domain name to a dynamic Internet IP address. The instructions in this chapter will guide you through the setup needed for use of the SoloLink DDNS Service. For the most current information about the SoloLink DDNS Service, visit www.linksys.com/sololink. For a free, 90-day trial period of your SoloLink account, use the Access ID Card included with the Camera. You may want to use the Linksys SoloLink DDNS Service if one of the following applies to you:
Dynamic IP Address - Your Internet service assigns you a dynamic IP address. Many Internet service providers
(ISPs) assign a new IP address to your connection from time to time (for security purposes), or whenever you disconnect and reconnect. The SoloLink service keeps track of your networks address, even when it changes, so you can find the Camera. Convenience - There are a couple of ways the SoloLink service can be convenient. If you have a static IP address, you can use the SoloLink service to enter a name and port number for remote access of the Camera via the Internet. Theres no need to type an entire IP address. For example, you can give a Camera a name such as cam1.myhouse.ourlinksys.com. Also, some DDNS services require your PC to continuously run software that lets them keep track of your IP address. If your PC isnt powered on when your IP address changes, you wont be able to find the Camera on the Internet. The SoloLink service keeps track of where the Camera is. Setup Wizard for the SoloLink DDNS Service 1. On the Welcome or Congratulations screen of the Setup Wizard, click the Setup SoloLink DDNS Service button. Chapter 7: Setting up the Linksys SoloLink DDNS Service Overview Figure 7-1: SoloLink Service Figure 7-2: SoloLink Welcome Screen 33 Compact Wireless-G Internet Video Camera 2. This screen explains why you would want to use the SoloLink DDNS Service if your network is using a dynamic IP address. Click the Next button. 3. This screen explains why you would find the SoloLink DDNS Service convenient if you would prefer to access the Camera using a name rather than a series of numbers (its IP address). Click the Next button. Figure 7-3: SoloLink for Dynamic IP Address Screen Figure 7-4: SoloLink for Convenience Screen Chapter 7: Setting up the Linksys SoloLink DDNS Service Setup Wizard for the SoloLink DDNS Service 34 Compact Wireless-G Internet Video Camera 4. Make sure your network has an active Internet connection. Verify that your PC and Camera are connected to the network and the Camera is configured properly. Click Next. 5. This screen displays a list of Compact Wireless-G Internet Video Cameras on your network and their status information. In the Selection box, click the name of the Camera you are currently setting up. Click Next. Figure 7-5: Check Connections Screen Figure 7-6: Cameras Found Screen Chapter 7: Setting up the Linksys SoloLink DDNS Service Setup Wizard for the SoloLink DDNS Service 35 Compact Wireless-G Internet Video Camera 6. To ensure security, you will be asked to enter a user name and password before you can access the Camera. If you have not changed the Cameras user name and password, then enter admin in the User name and Password fields (admin is the default). Then click OK. 7. Your web browser will automatically start up, and the SoloLink DDNS screen of the Cameras Web-based Utility will appear. Click New User ? - Click here to Register. Figure 7-7: Login Screen Figure 7-8: SoloLink DDNS Screen Chapter 7: Setting up the Linksys SoloLink DDNS Service Setup Wizard for the SoloLink DDNS Service 36 Compact Wireless-G Internet Video Camera 8. Make sure your network has an active Internet connection. Click Continue. 9. On the Welcome to the SoloLink DDNS Service screen, click Set up a NEW Account. Figure 7-9: Confirm Active Internet Connection Screen Figure 7-10: Welcome to the SoloLink DDNS Service Screen Chapter 7: Setting up the Linksys SoloLink DDNS Service Setup Wizard for the SoloLink DDNS Service 37 Compact Wireless-G Internet Video Camera 10. On the Sign Up screen, enter the Access ID for your free trial offer. It is provided on the Promotion Card included with the Camera. (If you dont have an Access ID, then leave the Access ID field blank.) Then enter your account and user information. Enter a Username and Password for your account. Enter the Password again in the Confirm Password field. Complete the following required fields: First Name, Last Name, Phone, and Email. You can also enter your postal address and choose to receive updates by e-mail. Then click Continue. Figure 7-11: Sign Up Screen Chapter 7: Setting up the Linksys SoloLink DDNS Service Setup Wizard for the SoloLink DDNS Service 38 Compact Wireless-G Internet Video Camera 11. Review your information on the Confirmation screen. If the new settings are correct, click Continue. 12. On the Select a Location ID screen, enter a Location ID, which can be a name describing your networks location. It will be combined with the Cameras Device Name and ourlinksys.com to create a convenient URL you can use to access the Camera. Click Continue. Figure 7-12: Confirmation of New Settings Screen Chapter 7: Setting up the Linksys SoloLink DDNS Service Setup Wizard for the SoloLink DDNS Service 39 Figure 7-13: Select a Location ID Screen Compact Wireless-G Internet Video Camera 13. On the Confirm your Location ID screen, verify that the Location ID is correct. Then click Continue. 14. On the Payment screen, choose one of two payment plans, Bill me now or Bill me later. (If you did not enter an Access ID, then you have one choice, Bill me now.) If you click Bill me later, go to step 15. If you click Bill me now, you will see a screen asking for billing information. Follow the on-screen instructions and then go to step 15. Figure 7-14: Confirm Your Location ID Screen 15. Read the Terms of Service agreement on the Verification screen. Click Create Account to accept the terms of service. Figure 7-15: Payment Screen Chapter 7: Setting up the Linksys SoloLink DDNS Service Setup Wizard for the SoloLink DDNS Service Figure 7-16: Verification Screen 40 Compact Wireless-G Internet Video Camera 16. On the Create Links screen, click Continue. The SoloLink DDNS Service will send your account information to the Camera. 17. A pop-up screen will inform you that you have successfully registered your account. Click OK. At the bottom of the SoloLink DDNS screen, click the Apply button to register the Camera with your account. Figure 7-17: Create Links Screen Figure 7-18: Successful Registration Screen Chapter 7: Setting up the Linksys SoloLink DDNS Service Setup Wizard for the SoloLink DDNS Service 41 Compact Wireless-G Internet Video Camera 18. A confirmation page will display the link or address you will use to access the Camera and the port number the SoloLink DDNS Service will use to find the Camera. Click Continue. 19. A pop-up screen will inform you that you have successfully set up the SoloLink DDNS Service for the Camera. Click OK. NOTE: Make sure you set up the port forwarding feature on your network router, so the SoloLink DDNS Service will be able to access the Camera. Figure 7-20: Successful Setup Screen Figure 7-19: Account Confirmation of Camera Screen Chapter 7: Setting up the Linksys SoloLink DDNS Service Setup Wizard for the SoloLink DDNS Service 42 Compact Wireless-G Internet Video Camera 20. Set up port forwarding on your network router, so the SoloLink DDNS Service will be able to track the Compact Wireless-G Internet Video Camera. Go to www.linksys.com/portfwd for instructions on how to configure a Linksys router. For other routers, refer to your routers documentation. The SoloLink DDNS setup is complete. If you want to register more Cameras with your SoloLink account, proceed to the SoloLink Registration of Additional Cameras section. For more information about the Cameras Web-based Utility, proceed to Chapter 8: Using the Compact Wireless-G Internet Video Camera Web-based Utility. SoloLink Registration of Additional Cameras Figure 7-21: Port Forwarding Information After you have set up your SoloLink account, you can add more Cameras to your SoloLink account using each Cameras Web-based Utility. Follow these instructions for each Camera you add:
1. To access a Cameras Web-based Utility, launch Internet Explorer, and enter the Cameras IP address in the Address field. (The default IP address is 192.168.1.115.) Then press Enter. 2. The Welcome screen will appear. Click the Setup tab. 3. A login screen will appear. (Windows XP users will see a similar screen.) Enter admin (the default user name and password) in the User Name and Password fields. Then click the OK button. 4. Click the SoloLink DDNS tab. Figure 7-22: Web-based Utility Welcome Chapter 7: Setting up the Linksys SoloLink DDNS Service SoloLink Registration of Additional Cameras Figure 7-23: Web Utility Login Screen 43 Compact Wireless-G Internet Video Camera 5. 6. 7. In the Username, Password, and Your Domain fields, enter your SoloLink account information. In the Device Name field, give the Camera a unique name. The DDNS service will not work if multiple Cameras have the same Device Name. In the WAN Port field, enter a unique port number. This is the number of the port you will use to access the Camera remotely. (If you need to find an available port, click Find Available Port and follow the on-screen instructions). The DDNS service will not work if multiple Cameras use the same WAN port. 8. Depending on how often you want the DDNS service to update the dynamic IP address, select the appropriate time interval from the DDNS Service Update drop-down menu. To update the dynamic IP address immediately, click the Update Now button. 9. Click the Apply button on the SoloLink DDNS screen. The Camera will automatically register itself with your Figure 7-24: SoloLink DDNS Screen SoloLink account. 10. Set up port forwarding on your network router, so the SoloLink DDNS Service will be able to track the Compact Wireless-G Internet Video Camera. Go to www.linksys.com/portfwd for instructions on how to configure a Linksys router. For other routers, refer to your routers documentation. The Camera has been added to your SoloLink account. For more information about the Cameras Web-based Utility, proceed to Chapter 8: Using the Compact Wireless-G Internet Video Camera Web-based Utility. Figure 7-25: Find Available Port Screen Chapter 7: Setting up the Linksys SoloLink DDNS Service SoloLink Registration of Additional Cameras 44 Compact Wireless-G Internet Video Camera Chapter 8: Using the Compact Wireless-G Internet Video Cameras Web-based Utility Overview Use the Cameras Web-based Utility to access and alter its settings. This chapter will describe each webpage in the Utility and its features. The Utility can be accessed via the web browser of a computer connected to the Camera. How to Access the Web-based Utility To access the Utility, launch Internet Explorer, and enter the Cameras IP address in the Address field. (The default IP address is 192.168.1.115.) Then press Enter. The Welcome screen of the Web-based Utility will appear. You have six tabs available:
Home. To return to the Welcome screen, click the Home tab.
View Video. To view the Cameras video, click the View Video tab. Go to the View Video section for more information.
Setup. To alter the Cameras settings, click the Setup tab. Go to the Setup section for more information.
Linksys Web. To go to the Linksys website, www.linksys.com, click the Linksys Web tab.
Help. The Help screen allows you to get information about the various Setup screens, download the latest Viewer & Recording Utility, download this User Guide, and download Acrobat Reader. Go to the Help section for more information.
Exit. To close the Utility, click the Exit tab. Figure 8-1: Cameras Default IP Address Figure 8-2: Web-based Utility Welcome Chapter 8: Using the Compact Wireless-G Internet Video Cameras Web-based Utility Overview 45 Compact Wireless-G Internet Video Camera View Video Follow these instructions to view the Cameras video. 1. Click the View Video tab on the Welcome screen. 2. A Security Warning screen about an OCX plug-in may appear. To enable your computer to see the Cameras video, click the Yes button. 3. A screen will appear showing you the video from the Camera. NOTE: To view video using a web browser, you must use Internet Explorer version 5.5 or higher. The View Video feature will not work with Netscape. Netscape users should use the Multi-Camera Viewer
& Recorder Utility instead. When viewing the Cameras video, you can resize the image, zoom, take and save snapshots, and view the image as a flip, mirror, or rotated image. Size Selection. The default is 320 x 240. You can also resize the image; select 640 x 480 (digitally resized) or 160 x 128 from the drop-down menu. Icon Function A digital zoom feature is available. To zoom in on a section of the window, click this icon. Then use your mouse to select the section you want to magnify. To take a snapshot of the current frame of video, click this icon. The snapshot will be automatically saved in the designated folder. To designate the folder where snapshots are saved, click this icon. To view the image as a flip image, click this icon. To view a mirror image (reversed left to right and vice versa), click this icon. To view the image as an image rotated 180, click this icon. Figure 8-3: Security Warning Screen Figure 8-4: View Video Screen Chapter 8: Using the Compact Wireless-G Internet Video Cameras Web-based Utility View Video 46 Compact Wireless-G Internet Video Camera Setup Click the Setup tab on the Welcome screen to alter the Cameras settings. A login screen will pop up. (Windows XP users will see a similar screen.) Enter admin (the default user name and password) in the User Name and Password fields. Then click the OK button. NOTE: For added security, you should always change the Login Name and Password through the Administrator screen of the Utility. The Basic screen will appear. You have six tabs available:
Basic. To configure the Cameras basic, LAN, and wireless settings, use the Basic screen. Figure 8-5: Web Utility Login Screen
Image. Customize the video settings on the Image screen.
Administrator. Alter the Administrator name and password o
Users. Designate users and their level of access to the Camera on this screen.
SoloLink DDNS. Set up and manage the SoloLink DDNS Service. DDNS (Dynamic Domain Name System) lets you assign a fixed host and domain name to a dynamic Internet IP address.
Options. The e-mail alert options, Universal Plug and Play (UPnP) setting, and Alternate Port settings are configured on the Options screen.
Status. Status information and a log are displayed on this screen. To save your changes, click the Apply button. To cancel any unsaved changes, click the Cancel button. To get additional information about a screens features, click the Help tab. Figure 8-6: Basic Screen Chapter 8: Using the Compact Wireless-G Internet Video Cameras Web-based Utility Setup 47 Compact Wireless-G Internet Video Camera Basic The Basic screen allows you to alter the Cameras settings, including the network and wireless configuration. Device Settings Device ID. Displayed here is the Cameras identification name, which is based on its MAC address. Camera Name. You may assign any name to the Camera. Unique, memorable names are helpful, especially if you are using multiple Cameras on the same wireless network. You can enter up to 15 characters. Description. Enter information about the Camera in this field. You can enter up to 32 characters. LED Operation. Click the Enable radio button if you want the Cameras LED to light up when the Camera is working. Click the Disable radio button if you want the LED permanently disabled. Current Date/Time. The current date and time are automatically displayed. Click the Sync with PC button if you want the Camera to synchronize its date and time with your PC. Time Zone. Select the time zone for the Cameras location. Adjust for daylight savings. To adjust the Cameras current time for daylight savings, click the checkbox. LAN Settings Configuration Type. If the Camera will obtain an IP address automatically from a DHCP server, then select Automatic Configuration - DHCP. If you will assign the Camera a static IP address, then select Fixed IP Address, and complete the IP Address, Subnet Mask, Gateway, and DNS fields. IP Address, Subnet Mask, Gateway, Primary DNS, Secondary DNS. Complete these fields if the Camera will use a static IP address. You need to enter at least one DNS address. Wireless Settings SSID. Enter the networks SSID or network name here. Network Type. Select the networks mode, Infrastructure or Ad-hoc. Channel No. If the Camera is set to ad-hoc mode, select its channel setting from the drop-down menu. Security. To enable wireless security, click the Edit Security Settings button. For more information, proceed to the Security Settings section. Chapter 8: Using the Compact Wireless-G Internet Video Cameras Web-based Utility Setup Figure 8-7: Basic - Device Settings Screen Figure 8-8: Basic - LAN and Wireless Settings Screen 48 Compact Wireless-G Internet Video Camera To save your changes, click the Apply button. To cancel any unsaved changes, click the Cancel button. To get additional information about the screens features, click the Help tab. Wireless Security Select the security method you want to use, WEP or WPA Personal (all devices on your wireless network must use the same security settings). Then follow the appropriate instructions. WPA Personal WPA Algorithm. TKIP is automatically selected as the encryption method. WPA Shared Key. Enter the WPA Shared Key (also called Passphrase or Pre-Shared Key) used by your wireless network. It must have 8-32 characters. To save your changes, click the Apply button. To cancel your changes, click the Cancel button. WEP TX Key. Select which WEP key (1-4) will be used when your networks access point or wireless router sends and receives data. WEP Encryption. Select the level of WEP encryption you wish to use, 64 Bit Keys (10 Hex chars) or 128 Bit Keys (26 Hex chars). Passphrase. Instead of manually entering WEP keys, you can use a Passphrase to generate them. It is case-
sensitive and should not be longer than 16 alphanumeric characters. (This Passphrase is compatible with Linksys wireless products only. If you are also using non-Linksys wireless products, you will need to enter your WEP keys manually on those products.) After entering the Passphrase, click the Generate button to create WEP key(s). Key 1-4. If you used a Passphrase, the WEP keys will be displayed after you have generated them. If you are not using a Passphrase, manually enter a set of values in each field. (For 128-bit WEP, only one WEP key is permitted.) If you are using 64-bit WEP encryption, then each key must consist of exactly 10 hexadecimal characters. If you are using 128-bit WEP encryption, then the key must consist of exactly 26 hexadecimal characters. Valid hexadecimal characters are 0 through 9 and A through F. Authentication. The default is set to Open System, for which the sender and the recipient do NOT use a WEP key for authentication. You can also choose Shared Key, when the sender and recipient use a WEP key for authentication. This setting should match the one on your networks access point or wireless router. To save your changes, click the Apply button. To cancel your changes, click the Cancel button. Figure 8-9: Wireless Security - WPA Personal Screen Figure 8-10: Wireless Security - WEP Screen Chapter 8: Using the Compact Wireless-G Internet Video Cameras Web-based Utility Setup 49 Compact Wireless-G Internet Video Camera Image The Image screen allows you to alter the Cameras video settings. Video Settings Resolution. Select the resolution you want for viewing or recording the Cameras video. Select 320*240 for higher resolution or 160*120 for lower resolution. Image Quality. The default is Normal. Select the level of quality you want for viewing or recording the Cameras video. The range varies from Very Low to Very High. You may find it helpful to know what the bit rates are for video viewing or recording at different resolutions and image quality levels. The following table lists these estimated bit rates. Figure 8-11: Image Screen NOTE: Video quality and/or performance may be affected by the number of users connected to the Camera. Estimated Bit Rates for Video Viewing or Recording Resolution Quality Level Bit Rate 320 x 240 320 x 240 320 x 240 320 x 240 320 x 240 160 x 120 160 x 120 160 x 120 160 x 120 160 x 120 Very High High Normal Low Very Low Very High High Normal Low Very Low 900kbps 500kbps 300kbps 120kbps 40kbps 800kbps 400kbps 200kbps 100kbps 40kbps Power line frequency. Because of how fluorescent lighting flickers, it can affect the quality of the Cameras video. Select 60 Hz if your fluorescent lighting uses 60 Hz line voltage. Select 50 Hz if your fluorescent lighting uses 50 Hz line voltage. Chapter 8: Using the Compact Wireless-G Internet Video Cameras Web-based Utility Setup 50 Compact Wireless-G Internet Video Camera Adjustments Color Balance. Select Auto if you want the Camera to adjust the brightness level automatically. Select Indoor
(Incandescent) if the Camera is in an environment using incandescent lighting, which is primarily used indoors. Select Fluorescent (white light) if the Camera is in an environment using fluorescent white lighting. Select Fluorescent (yellow light) if the Camera is in an environment using fluorescent yellow lighting.Select Outdoor if the Camera is used outdoors, exposed to sunlight. Exposure. The default is Normal. Select the level of exposure you want for the Cameras video. The range varies from -3 (underexposed) to +3 (overexposed). Sharpness. The default is Normal. Select the level of sharpness you want for the Cameras video. The range varies from -3 to +3. Options Image Rotation. If you want the image to be rotated 180, click the checkbox next to Rotate image 180. Time Stamp. If you want a time stamp shown on the video, click the checkbox next to Enable. Text Display. If you want text shown on the video, click the checkbox next to Enable. Then complete the Text field with up to 20 characters. To save your changes, click the Apply button. To cancel any unsaved changes, click the Cancel button. To get additional information about the screens features, click the Help tab. Chapter 8: Using the Compact Wireless-G Internet Video Cameras Web-based Utility Setup 51 Compact Wireless-G Internet Video Camera Administrator Use this screen to change the administrator login settings, restore factory defaults, and upgrade firmware. Login Changing the default name and password is recommended to secure access to the Cameras settings. Login Name. Complete this field with a name of your choice. Password and Verify Password. Enter your new password twice. (It should have eight or fewer characters.) Restore Factory Defaults Before you restore the Cameras factory default settings, write down any custom settings you have configured. You will need to re-configure the Camera after you have restored the factory defaults. Restore Factory Defaults. To restore the Cameras factory default settings, click the Restore Defaults button. Firmware Upgrade New firmware versions are posted at www.linksys.com and can be downloaded for free. If the Camera is functioning well, there is no need to download a newer firmware version, unless that version has a new feature that you want to use. Loading new firmware onto the Camera does not always enhance its performance. Linksys recommends that when you upgrade the Cameras firmware, use a computer within the Cameras local network. If you attempt to upgrade the Cameras firmware from a remote locationusing a computer outside of the Cameras local networkthe upgrade will fail. Upgrade Firmware. To upgrade the firmware, follow these instructions:
1. Go to www.linksys.com and download the firmware upgrade file for the Camera. Then extract the file. 2. Click the Upgrade Firmware button. 3. On the Upgrade Firmware screen, click the Browse button to find the extracted file, and then double-click it. 4. Click the Start Upgrade button, and follow the on-screen instructions. To cancel the upgrade, click the Cancel button. For further help, click the Help tab. To save your changes, click the Apply button. To cancel any unsaved changes, click the Cancel button. To get additional information about the screens features, click the Help tab. Chapter 8: Using the Compact Wireless-G Internet Video Cameras Web-based Utility Setup Figure 8-12: Administrator Screen NOTE: When you restore the Cameras factory defaults, you will lose the settings you have saved previously. NOTE: When you upgrade the Cameras firmware, you may lose the settings you have saved previously. Figure 8-13: Upgrade Firmware Screen 52 Compact Wireless-G Internet Video Camera Users The Users screen allows you to designate access rights for Camera users. User Access Allow access by. The default is All users. If you keep the default setting, then all users will be allowed to view the Cameras video. If you select Only users in database, then only the users you enter in the database will be allowed to view the Cameras video. They will be asked to log in using their user name and password whenever they request access to the Cameras video. Users You can enter up to eight users into the database. These users are then listed in the Users box. Edit. To modify a users settings, select the user in the Users box and click the Edit button. Make changes using the User Name, User Password, and Confirm Password fields. Then click the Apply button. Delete. To remove a user from the database, select the user in the Users box and click the Delete button. Then click the Apply button. Delete All. To remove all users from the database, click the Delete All button. Then click the Apply button. Add User. To add a new user, Complete the User Name, User Password, and Confirm Password fields. Click the Add User button. Then click the Apply button. Clear/Cancel. To clear the changes you have made in the User Name, User Password, and Confirm Password fields, click the Clear/Cancel button. To save your changes, click the Apply button. To cancel any unsaved changes, click the Cancel button. To get additional information about the screens features, click the Help tab. Figure 8-14: Users Screen Chapter 8: Using the Compact Wireless-G Internet Video Cameras Web-based Utility Setup 53 Compact Wireless-G Internet Video Camera SoloLink DDNS The SoloLink DDNS screen allows you to set up and configure your SoloLink DDNS Service. DDNS (Dynamic Domain Name System) lets you assign a fixed host and domain name to a dynamic Internet IP address. If you have already set up your SoloLink account, then you can use this screen to register additional Cameras. For instructions, go to the SoloLink Registration of Additional Cameras section on the following page. NOTE: If you use the Cameras DDNS feature, then you must also configure the port forwarding feature on your network router. Go to www.linksys.com/portfwd for instructions on how to configure a Linksys router. For other routers, refer to your routers documentation. SoloLink DDNS Username. Enter the username you have set up on your SoloLink account. If you are a new user, click New User?
- Click here to Register. The New User Registration screen will appear. Click the Continue button, or click the Back screen to return to the previous screen. Your web browser will automatically start up, and you will visit a website to set up your SoloLink account. Follow the on-screen instructions. For more information, refer to Chapter 7: Setting up the Linksys SoloLink DDNS Service, which will guide you through setup of your SoloLink account. Password. Enter the password you have set up on your SoloLink account. If you have forgotten your password, click Forgot your Password?
The Password Request screen will appear. Complete the Domain name field. Click the Continue button to request your username and password, which will be e-mailed to the e-mail address registered with your SoloLink DDNS account. Click the Cancel button to cancel your change. Click the Back button to return to the previous screen. Your Domain. Enter the host and domain name you have set up on your SoloLink account. It should be in this format: <Location ID>.ourlinksys.com. For example, if myhouse is the Location ID, then the host and domain name would be myhouse.ourlinksys.com. Device Name. Enter the name you have given the Camera. Figure 8-15: SoloLink DDNS Screen Figure 8-16: New User Registration Screen Chapter 8: Using the Compact Wireless-G Internet Video Cameras Web-based Utility Setup Figure 8-17: Password Request Screen 54 Compact Wireless-G Internet Video Camera WAN Port. Enter the number of the port you will use to remotely access the Camera. If you need to find an available port, click Find Available Port and follow the on-screen instructions. DDNS Service Update. Depending on how often you want the DDNS service to update the dynamic IP address, select the appropriate time interval from the drop-down menu. To update the dynamic IP address immediately, click the Update Now button. Status Registration Status. The status of the Cameras registration is displayed here. To use the SoloLink DDNS service for the Camera, it must be registered with your SoloLink DDNS account. Address Update Status. The status of the most recent DDNS service update is displayed here. You will be informed if the username and password authentication has been successful, as well as if the dynamic IP address has been updated. Last Update Attempt. The date and time of the most recent IP address update attempt are displayed here. Last Successful Update. The date and time of the most recent IP address update are displayed here. Options. If you want to manage your SoloLink DDNS account, click the DDNS Account button. Your web browser will automatically start up, and you will visit a website to manage your SoloLink account. Follow the on-screen instructions. If you want to remove the Camera from the DDNS service account, click the Remove Camera button. The Device Removal screen will appear. To remove the Camera, click the Remove button. Click the Back button to return to the previous screen. To save your changes, click the Apply button. To cancel any unsaved changes, click the Cancel button. To display the most recent information, click the Refresh button. To get additional information about the screens features, click the Help tab. SoloLink Registration of Additional Cameras After you have set up your SoloLink account, you can add more Cameras to your account, one at a time. Follow these instructions for each Camera you add:
1. On the SoloLink DDNS screen of the Cameras Web-based Utility, enter your SoloLink account information in the Username, Password, and Your Domain fields. Figure 8-18: SoloLink Screen, continued Figure 8-19: Manage Your SoloLink DDNS Account 2. In the Device Name field, give the Camera a unique name. The DDNS service will not work if multiple Cameras have the same Device Name. Figure 8-20: Device Removal Screen Chapter 8: Using the Compact Wireless-G Internet Video Cameras Web-based Utility Setup 55 Compact Wireless-G Internet Video Camera 3. In the WAN Port field, enter a unique port number. This is the number of the port you will use to access the Camera remotely. If you need to find an available port, click Find Available Port and follow the on-screen instructions. The DDNS service will not work if multiple Cameras use the same WAN port. 4. Depending on how often you want the DDNS service to update the dynamic IP address, select the appropriate time interval from the DDNS Service Update drop-down menu. To update the dynamic IP address immediately, click the Update Now button. 5. Click the Apply button on the SoloLink DDNS screen. The Camera will automatically register itself with your SoloLink account. 6. Set up port forwarding on your network router, so the SoloLink DDNS Service will be able to track the Compact Wireless-G Internet Video Camera. Go to www.linksys.com/portfwd for instructions on how to configure a Linksys router. For other routers, refer to your routers documentation. Figure 8-21: Find Available Port Screen Chapter 8: Using the Compact Wireless-G Internet Video Cameras Web-based Utility Setup 56 Compact Wireless-G Internet Video Camera Options The Options screen allows you to alter the Cameras e-mail alert features, UPnP configuration, and Alternate Port settings. E-mail Alert You can choose to be notified when the Camera detects motion in its field of view. You will be sent a text-only e-mail or an e-mail with video attached. NOTE: The Camera's motion sensitivity and range will vary depending on the light conditions of your environment. E-mail Alert. If you want to be notified by e-mail when the Camera detects motion, then select Enable from the drop-down menu. Otherwise, select Disable. Send to. In each field, enter an e-mail address that will receive e-mail alerts. (You can enter up to three e-mail addresses.) Show From as. Enter the text that you want displayed in the From field of any e-mail alert message. Subject. Enter the subject heading that you want to be used. Mail SMTP Server. Enter the IP address of the outgoing mail SMTP server. If it requires authentication, click the checkbox, and enter the account name and password in the Account Name and Password fields. Delay between E-mails. Specify the minimum time interval between e-mail alerts. The default is 2 minutes. E-Mail Video. If you want e-mail sent with a video attachment, select Enable from the drop-down menu. Then select the length of video you want, up to a maximum of 5 seconds. The default is 2 seconds. If you want text-
only e-mail sent to you, select Disable from the drop-down menu. Motion Detection. To specify where and how the Camera should monitor for motion, click the Set Area &
Sensitivity button. Two motion detection areas will be shown in windows labeled Area 1 and Area 2. Use your mouse to move them around to the areas you want the Camera to monitor. Sections labeled Detected Area 1 and Detected Area 2 show additional settings. For each area, click the checkbox next to Enable if you want that area monitored. Then slide the bar left (less sensitive) or right (more sensitive) to adjust the Threshold (sensitivity) level. Click the Save button to save your changes. Chapter 8: Using the Compact Wireless-G Internet Video Cameras Web-based Utility Setup Figure 8-22: Options Screen Figure 8-23: Options Screen, continued Figure 8-24: Motion Detection Screen 57 Compact Wireless-G Internet Video Camera Other UPnP. When enabled, the Cameras Universal Plug and Play (UPnP) feature allows a UPnP-enabled computer to easily detect the Camera. If your computer is UPnP-enabled, then select Enable. Alternate Port. If you want the Camera to be able to use an alternate port for HTTP/web connections, select Enable. Then enter the port number you want in the Port Number field. To save your changes, click the Apply button. To cancel any unsaved changes, click the Cancel button. To get additional information about the screens features, click the Help tab. Chapter 8: Using the Compact Wireless-G Internet Video Cameras Web-based Utility Setup 58 Compact Wireless-G Internet Video Camera Status The Status screen allows you to view the Cameras status information. System Status Firmware Version. The version number of the firmware currently installed is displayed here. Firmware should only be upgraded from the Help screen if you experience problems with the Camera. Visit www.linksys.com to find out if there is updated firmware. MAC Address. The MAC Address of the Camera is displayed here. Camera Name. The name you gave to the Camera is displayed here. Description. The information about the Camera that you entered is displayed here. Date/Time. The current date and time are shown here. Network Network Type. The type of network is shown here. IP Address. The Cameras IP Address is displayed here. Subnet Mask. The Cameras Subnet Mask is shown here. Gateway. The IP address of the Cameras Gateway is displayed here. Wireless SSID. The SSID or wireless network name of the Camera is shown here. Channel. The channel setting of the Camera is displayed here. Security. The wireless security setting of the Camera is shown here. To get the Cameras most up-to-date information, click the Refresh button. To get additional information about the screens features, click the Help tab. Figure 8-25: Status Screen Chapter 8: Using the Compact Wireless-G Internet Video Cameras Web-based Utility Setup 59 Compact Wireless-G Internet Video Camera Help Through the Help screen, youll find links to additional resources for the Camera and its Utility. If you click the Help tab directly from the Welcome screen, then you will see the User Help screen and will only be able to access the link to the Linksys support page for downloading the latest Multi-Camera Viewer & Recorder Utility, as well as view information about the View Video feature. NOTE: The appearance and features of the Help screen will vary depending on whether you have logged in first to access the Setup. If you first log in to access the Cameras Setup and then click the Help tab, you will see the Administrator Help screen and will be able to access these resources:
Setup. Click any of the topics in the bar on the left to get help information. Linksys Support Page - Download Latest Viewer/Recorder Utility. Click this link to download the most recent version of the Multi-Camera Viewer & Recorder Utility from the Linksys website, www.linksys.com. Click here to learn how to configure Port Forwarding in your Linksys Router. If you are going to use the SoloLink DDNS Service, you need to set up port forwarding on your router. For instructions on how to configure a Linksys router, click this link. If you have a different router, refer to your routers documentation. Adobe website (software for viewing PDF documents). If you do not have the Acrobat Reader, click the Adobe website link to download it. Figure 8-26: User Help Screen Figure 8-27: Administrator Help Screen Chapter 8: Using the Compact Wireless-G Internet Video Cameras Web-based Utility Help 60 Compact Wireless-G Internet Video Camera Appendix A: Troubleshooting This appendix consists of two parts: Common Problems and Solutions and Frequently Asked Questions. This appendix provides solutions to problems that may occur during the installation and operation of the Compact Wireless-G Internet Video Camera. Read the description below to solve your problems. If you can't find an answer here, check the Linksys website at www.linksys.com. Common Problems and Solutions 1. I cant view the Cameras video using Internet Explorer. Make sure the OCX plug-in was correctly installed. If youre not sure, re-install the plug-in by following these instructions:
On the Welcome screen of the Cameras Web-based Utility, click the View Video button.
A screen mentioning a security warning about an OCX plug-in will appear. Click the Yes button to allow the plug-in to be installed.
You should then be able to view the Cameras streaming video. If you still cannot view the video, make sure you have the rights to install the plug-in in your PCs Internet Explorer. If not, log into your computer as an administrator and install the plug-in. Then you can check if the OCX plug-in has been installed. Follow these instructions:
From Internet Explorer, go to Tools and Internet Options.
On the General screen, click Settings under Temporary Internet files.
Click View Objects. You should see a file named NetCamPlayerWeb Control installed. 2. The OCX plug-in is installed in Internet Explorer, but I cannot view any video. Make sure you have Microsoft Internet Explorer 5.5 or higher installed. Then delete the OCX plug-in by following these instructions:
From Internet Explorer, go to Tools and Internet Options.
On the General screen, click Settings under Temporary Internet files.
Click View Objects.
You should see a file named NetCamPlayerWeb Control installed. Delete this file from the list.
The next time you click View Video from the web browser, you will be prompted to re-install the OCX plug-
in. 3. When powering on the Camera, I cant immediately access the Camera from my computer. Make sure the Cameras LED is continuously lit. When it is flashing, the Camera is initializing. Appendix A: Troubleshooting Common Problems and Solutions 61 Compact Wireless-G Internet Video Camera 4. 5. 6. Im not able to play my recording video files. Make sure you have Microsoft Windows Media Player 7 or higher. If you dont, you can download the latest version from www.microsoft.com. I have two Cameras and see two WVC54GCs listed in my Multi-Camera Viewer & Recorder Utility. When I click to view both Cameras, I see the video of only one Camera. Make sure that the Cameras have different camera or device names. You can change this by using the Web-
based Utility or running the Setup Wizard. If you use the Web-based Utility, log in and click the Setup tab. Then on the Basic screen, change the Camera Name. I want to set up an account with the SoloLink DDNS Service, but I cant access the SoloLink website to sign up. Make sure the Camera is properly configured on your local network. Then check to see if your PC and Camera are properly connected and your network has an active Internet connection. 7. When I view video remotely via the Internet, the video is very slow. Video performance is greatly affected by your Internet connection speed. You can lower the Cameras image quality to speed up the video. Through the Cameras Web-based Utility, click the Setup and Image tabs, and then lower the image quality on the Image screen. 8. 9. I cannot access the Setup tab of the Cameras Web-based Utility. Make sure you have administrator rights. Only an administrator can change the Cameras settings. I want to access the Camera when Im away from home, but somehow I cant connect. If your network uses a dynamic IP address supplied by your ISP, then the IP address you use to reach the Camera will change as well. You need to use the Linksys SoloLink DDNS Service, so you can access the Camera using its domain name while the service keeps track of the IP address changes. To set up a Dynamic Domain Name Service (DDNS) account, click the Setup tab of the Cameras Web-based Utility. Click the SoloLink DDNS tab. If you are a new user, click New User? - Click here to Register. Follow the on-screen instructions. You can also set up the Linksys SoloLink DDNS Service by inserting the Setup CD-ROM into your PCs CD-ROM drive. Click the Setup SoloLink DDNS Service button, and follow the on-screen instructions. For more information, see Chapter 7: Setting up the Linksys SoloLink DDNS Service. Important: To allow remote access to the Camera, you will also have to use the port forwarding feature on your network router. Appendix A: Troubleshooting Common Problems and Solutions 62 Compact Wireless-G Internet Video Camera 10. I already set up my SoloLink DDNS account, but I cant access the Camera from a remote location. Follow these instructions:
When you enter the Cameras domain name, make sure it is in this format:
http://<Device Name>.<Location ID>.ourlinksys.com The <Device Name> is the name you gave the Camera when you ran the Setup Wizard. The <Location ID>
is the name you selected when you set up your SoloLink DDNS account.
If the Camera is set to DHCP, make sure your local network is working properly and your router has an active Internet connection.
If the Camera uses a static IP address, insert the Setup CD-ROM into your network PCs CD-ROM drive. Click the Setup button and follow the on-screen instructions. When you see the IP Settings screen, make sure the Cameras Default Gateway and Primary DNS addresses are correct. For more information, refer to Chapter 5: Setting up and Mounting the Compact Wireless-G Internet Video Camera. Frequently Asked Questions Can I view video using a Macintosh or Netscape Navigator?
The Camera is designed for computers running a Windows operating system and Internet Explorer 5.5 or higher. You cannot view video on a Macintosh. If you only have Netscape, you can view video using the Multi-Camera Viewer & Recorder Utility. See Chapter 6: Installing and Using the Compact Wireless-G Internet Video Camera Multi-Camera Viewer & Recorder Utility. Can I directly connect the Camera to wired and wireless networks at the same time?
No. Before powering on the Camera, you should decide if you want to connect the Camera to a wireless network via an access point or to a wired network. If your wireless and wired networks are bridged, then you can access the Camera from any networked computer, but the Camera must be directly connected to only one of the networks. To connect the Camera to a wireless network, power on the Camera with no network cable attached. The Camera will be ready for use when the LED is lit continuously. To connect the Camera to a wired network, connect the network cable to the Camera, and then power it on. The Camera will be ready for use when the LED is lit continuously. Can I install the Camera outdoors?
No, the Camera was not designed for outdoors usage. Ive recorded video for a few hours. Why do I see multiple files saved on my computer?
The recording function saves video in chunks; each chunk is a maximum of one hour in duration. For example, if you have recorded five continuous hours, then you will see five files saved on your computer. This keeps files from getting too large. Appendix A: Troubleshooting Frequently Asked Questions 63 Compact Wireless-G Internet Video Camera Do I need to install the Linksys Multi-Camera Viewer and Recorder Utility?
Installation is optional. You can view video using Microsoft Internet Explorer 5.5 or higher. If you dont want to use the recording function, then you dont need to install the Multi-Camera Viewer and Recorder Utility. Where can I find more information about the Linksys SoloLink DDNS Service?
You can go to www.linksys.com/sololink for more information. Can I specify who gets to view the Cameras video?
Yes. Access the Cameras Web-based Utility, and click the Setup tab. After you log in, click the Users tab. You will be able to restrict access to users you have entered in the database. See Chapter 8: Using the Compact Wireless-G Internet Video Camera Web-based Utility. Can I add a time stamp to the video?
Yes. Access the Cameras Web-based Utility, and click the Setup tab. After you log in, click the Image tab. You will be able to add a time stamp as well as descriptive text to the video. See Chapter 8: Using the Compact Wireless-G Internet Video Camera Web-based Utility. How many users can view the Cameras video at the same time?
Users at four different PCs can simultaneously view the Cameras video. What is the IEEE 802.11b standard?
It is one of the IEEE standards for wireless networks. The 802.11b standard allows wireless networking hardware from different manufacturers to communicate, provided that the hardware complies with the 802.11b standard. The 802.11b standard states a maximum data transfer rate of 11Mbps and an operating frequency of 2.4GHz. What is the IEEE 802.11g standard?
It is one of the IEEE standards for wireless networks. The 802.11g standard allows wireless networking hardware from different manufacturers to communicate, provided that the hardware complies with the 802.11g standard. The 802.11g standard states a maximum data transfer rate of 54Mbps and an operating frequency of 2.4GHz. What IEEE 802.11b features are supported?
The product supports the following IEEE 802.11b functions:
CSMA/CA plus Acknowledge protocol
Multi-Channel Roaming
Automatic Rate Selection
RTS/CTS feature
Fragmentation
Power Management Appendix A: Troubleshooting Frequently Asked Questions 64 Compact Wireless-G Internet Video Camera What IEEE 802.11g features are supported?
The product supports the following IEEE 802.11g functions:
CSMA/CA plus Acknowledge protocol
OFDM protocol
Multi-Channel Roaming
Automatic Rate Selection
RTS/CTS feature
Fragmentation
Power Management What is ad-hoc mode?
When a wireless network is set to ad-hoc mode, the wireless-equipped computers are configured to communicate directly with each other. The ad-hoc wireless network will not communicate with any wired network. What is infrastructure mode?
When a wireless network is set to infrastructure mode, the wireless network is configured to communicate with a wired network through a wireless access point or router. Appendix A: Troubleshooting Frequently Asked Questions 65 Compact Wireless-G Internet Video Camera Appendix B: Wireless Security Linksys wants to make wireless networking as safe and easy for you as possible. The current generation of Linksys products provide several network security features, but they require specific action on your part for implementation. So, keep the following in mind whenever you are setting up or using your wireless network. Security Precautions The following is a complete list of security precautions to take (at least steps 1 through 5 should be followed):
1. Change the default SSID. 2. Disable SSID Broadcast. 3. Change the default password for the Administrator account. 4. Enable MAC Address Filtering. 5. Change the SSID periodically. 6. Use the highest encryption algorithm possible. Use WPA if it is available. Please note that this may reduce your network performance. 7. Change the encryption keys periodically. Security Threats Facing Wireless Networks Wireless networks are easy to find. Hackers know that in order to join a wireless network, wireless networking products first listen for beacon messages. These messages can be easily decrypted and contain much of the networks information, such as the networks SSID (Service Set Identifier). Here are the steps you can take:
Change the administrators password regularly. With every wireless networking device you use, keep in mind that network settings (SSID, WEP keys, etc.) are stored in its firmware. Your network administrator is the only person who can change network settings. If a hacker gets a hold of the administrators password, he, too, can change those settings. So, make it harder for a hacker to get that information. Change the administrators password regularly. NOTE: Some of these security features are available only through the network router or access point. Refer to the router or access points documentation for more information. Appendix B: Wireless Security Security Precautions 66 Compact Wireless-G Internet Video Camera SSID. There are several things to keep in mind about the SSID:
1. Disable Broadcast 2. Make it unique 3. Change it often Most wireless networking devices will give you the option of broadcasting the SSID. While this option may be more convenient, it allows anyone to log into your wireless network. This includes hackers. So, dont broadcast the SSID. Wireless networking products come with a default SSID set by the factory. (The Linksys default SSID is linksys.) Hackers know these defaults and can check these against your network. Change your SSID to something unique and not something related to your company or the networking products you use. Change your SSID regularly so that any hackers who have gained access to your wireless network will have to start from the beginning in trying to break in. MAC Addresses. Enable MAC Address filtering. MAC Address filtering will allow you to provide access to only those wireless nodes with certain MAC Addresses. This makes it harder for a hacker to access your network with a random MAC Address. WEP Encryption. Wired Equivalent Privacy (WEP) is often looked upon as a cure-all for wireless security concerns. This is overstating WEPs ability. Again, this can only provide enough security to make a hackers job more difficult. There are several ways that WEP can be maximized:
1. Use the highest level of encryption possible 2. Use Shared Key authentication 3. Change your WEP key regularly WPA. Wi-Fi Protected Access (WPA) is the newest and best available standard in Wi-Fi security. For encryption, WPA Personal automatically uses Temporal Key Integrity Protocol (TKIP), which incorporates Message Integrity Code (MIC) to provide protection against hackers. For the Passphrase field, enter the key shared by the devices on your wireless network. (This key should have 8-63 characters and can also be called a WPA shared key or pre-
shared key.) IMPORTANT: Always remember that each device in your wireless network MUST use the same encryption method and encryption key or your wireless network will not function properly. Appendix B: Wireless Security Security Threats Facing Wireless Networks 67 Compact Wireless-G Internet Video Camera Implementing encryption may have a negative impact on your networks performance, but if you are transmitting sensitive data over your network, encryption should be used. These security recommendations should help keep your mind at ease while you are enjoying the most flexible and convenient technology Linksys has to offer. Appendix B: Wireless Security Security Threats Facing Wireless Networks 68 Compact Wireless-G Internet Video Camera Appendix C: Upgrading Firmware NOTE: Linksys recommends that you upgrade the Cameras firmware within your network; in other words, use a computer within the Cameras local network. If you attempt to upgrade the Cameras firmware from a remote locationusing a computer outside of the Cameras local networkthe upgrade will fail. The Camera's firmware is upgraded through the Web-based Utility's Administrator tab. Follow these instructions:
To upgrade the firmware, follow these instructions:
1. Go to www.linksys.com and download the firmware upgrade file for the Camera. Then extract the file. 2. Click the Upgrade Firmware button on the Administrator screen. 3. On the Upgrade Firmware screen, click the Browse button to find the extracted file, and then double-click it. 4. Click the Start Upgrade button, and follow the on-screen instructions. To cancel the upgrade, click the Cancel button. For further help, click the Help tab. Figure C-1: Upgrade Firmware Screen Appendix C: Upgrading Firmware 69 Compact Wireless-G Internet Video Camera Appendix D: Windows Help Almost all wireless products require Microsoft Windows. Windows is the most used operating system in the world and comes with many features that help make networking easier. These features can be accessed through Windows Help and are described in this appendix. TCP/IP Before a computer can communicate with an access point or router, TCP/IP must be enabled. TCP/IP is a set of instructions, or protocol, all PCs follow to communicate over a network. This is true for wireless networks as well. Your PCs will not be able to utilize wireless networking without having TCP/IP enabled. Windows Help provides complete instructions on enabling TCP/IP. Shared Resources If you wish to share printers, folders, or files over your network, Windows Help provides complete instructions on using shared resources. Network Neighborhood/My Network Places Other PCs on your network will appear under Network Neighborhood or My Network Places (depending upon the version of Windows youre running). Windows Help provides complete instructions on adding PCs to your network. Appendix D: Windows Help 70 Compact Wireless-G Internet Video Camera Appendix E: Glossary 802.11b - An IEEE wireless networking standard that specifies a maximum data transfer rate of 11Mbps and an operating frequency of 2.4GHz. 802.11g - An IEEE wireless networking standard that specifies a maximum data transfer rate of 54Mbps, an operating frequency of 2.4GHz, and backward compatibility with 802.11b devices. Access Point - A device that allows wireless-equipped computers and other devices to communicate with a wired network. Also used to expand the range of a wireless network. Adapter - A device that adds network functionality to your PC. Ad-hoc - A group of wireless devices communicating directly with each other (peer-to-peer) without the use of an access point. Backbone - The part of a network that connects most of the systems and networks together, and handles the most data. Bandwidth - The transmission capacity of a given device or network. Beacon Interval - Data transmitted on your wireless network that keeps the network synchronized. Bit - A binary digit. Boot - To start a device and cause it to start executing instructions. Bridge - A device that connects different networks. Broadband - An always-on, fast Internet connection. Browser - An application program that provides a way to look at and interact with all the information on the World Wide Web. Buffer - A shared or assigned memory area that is used to support and coordinate different computing and networking activities so one isn't held up by the other. Byte - A unit of data that is usually eight bits long Appendix E: Glossary 71 Compact Wireless-G Internet Video Camera Cable Modem - A device that connects a computer to the cable television network, which in turn connects to the Internet. CSMA/CA (Carrier Sense Multiple Access/Collision Avoidance) - A method of data transfer that is used to prevent data collisions. CTS (Clear To Send) - A signal sent by a wireless device, signifying that it is ready to receive data. Daisy Chain - A method used to connect devices in a series, one after the other. Database - A collection of data that is organized so that its contents can easily be accessed, managed, and updated. DDNS (Dynamic Domain Name System) - Allows the hosting of a website, FTP server, or e-mail server with a fixed domain name (e.g., www.xyz.com) and a dynamic IP address. Default Gateway - A device that forwards Internet traffic from your local area network. DHCP (Dynamic Host Configuration Protocol) - A networking protocol that allows administrators to assign temporary IP addresses to network computers by leasing an IP address to a user for a limited amount of time, instead of assigning permanent IP addresses. DMZ (Demilitarized Zone) - Removes the Router's firewall protection from one PC, allowing it to be seen from the Internet. DNS (Domain Name Server) - The IP address of your ISP's server, which translates the names of websites into IP addresses. Domain - A specific name for a network of computers. Download - To receive a file transmitted over a network. DSL (Digital Subscriber Line) - An always-on broadband connection over traditional phone lines. DSSS (Direct-Sequence Spread-Spectrum) - Frequency transmission with a redundant bit pattern resulting in a lower probability of information being lost in transit. DTIM (Delivery Traffic Indication Message) - A message included in data packets that can increase wireless efficiency. Dynamic IP Address - A temporary IP address assigned by a DHCP server. Appendix E: Glossary 72 Compact Wireless-G Internet Video Camera Encryption - Encoding data transmitted in a network. Ethernet - IEEE standard network protocol that specifies how data is placed on and retrieved from a common transmission medium. Finger - A program that tells you the name associated with an e-mail address. Firewall - A set of related programs located at a network gateway server that protects the resources of a network from users from other networks. Firmware - The programming code that runs a networking device. Fragmentation -Breaking a packet into smaller units when transmitting over a network medium that cannot support the original size of the packet. FTP (File Transfer Protocol) - A protocol used to transfer files over a TCP/IP network. Full Duplex - The ability of a networking device to receive and transmit data simultaneously. Gateway - A device that interconnects networks with different, incompatible communications protocols. Half Duplex - Data transmission that can occur in two directions over a single line, but only one direction at a time. Hardware - The physical aspect of computers, telecommunications, and other information technology devices. HTTP (HyperText Transport Protocol) - The communications protocol used to connect to servers on the World Wide Web. IEEE (The Institute of Electrical and Electronics Engineers) - An independent institute that develops networking standards. Infrastructure - A wireless network that is bridged to a wired network via an access point. IP (Internet Protocol) - A protocol used to send data over a network. IP Address - The address used to identify a computer or device on a network. IPCONFIG - A Windows 2000 and XP utility that displays the IP address for a particular networking device. ISM band - Radio bandwidth utilized in wireless transmissions. ISP (Internet Service Provider) - A company that provides access to the Internet. Appendix E: Glossary 73 Compact Wireless-G Internet Video Camera LAN - The computers and networking products that make up your local network. MAC (Media Access Control) Address - The unique address that a manufacturer assigns to each networking device. Mbps (MegaBits Per Second) - One million bits per second; a unit of measurement for data transmission. mIRC - An Internet Relay Chat program that runs under Windows. Multicasting - Sending data to a group of destinations at once. NAT (Network Address Translation) - NAT technology translates IP addresses of a local area network to a different IP address for the Internet. Network - A series of computers or devices connected for the purpose of data sharing, storage, and/or transmission between users. NNTP (Network News Transfer Protocol) - The protocol used to connect to Usenet groups on the Internet. Node - A network junction or connection point, typically a computer or work station. OFDM (Orthogonal Frequency Division Multiplexing) - Frequency transmission that separates the data stream into a number of lower-speed data streams, which are then transmitted in parallel to prevent information from being lost in transit. Packet - A unit of data sent over a network. Passphrase - Used much like a password, a passphrase simplifies the WEP encryption process by automatically generating the WEP encryption keys for Linksys products. Ping (Packet INternet Groper) - An Internet utility used to determine whether a particular IP address is online. POP3 (Post Office Protocol 3) - A standard mail server commonly used on the Internet. Port - The connection point on a computer or networking device used for plugging in cables or adapters. Power over Ethernet (PoE) - A technology enabling an Ethernet network cable to deliver both data and power. PPPoE (Point to Point Protocol over Ethernet) - A type of broadband connection that provides authentication
(username and password) in addition to data transport. PPTP (Point-to-Point Tunneling Protocol) - A VPN protocol that allows the Point to Point Protocol (PPP) to be tunneled through an IP network. This protocol is also used as a type of broadband connection in Europe. Appendix E: Glossary 74 Compact Wireless-G Internet Video Camera Preamble - Part of the wireless signal that synchronizes network traffic. RJ-45 (Registered Jack-45) - An Ethernet connector that holds up to eight wires. Roaming - The ability to take a wireless device from one access point's range to another without losing the connection. Router - A networking device that connects multiple networks together. RTS (Request To Send) - A networking method of coordinating large packets through the RTS Threshold setting. Server - Any computer whose function in a network is to provide user access to files, printing, communications, and other services. SMTP (Simple Mail Transfer Protocol) - The standard e-mail protocol on the Internet. SNMP (Simple Network Management Protocol) - A widely used network monitoring and control protocol. Software - Instructions for the computer. A series of instructions that performs a particular task is called a program. SOHO (Small Office/Home Office) - Market segment of professionals who work at home or in small offices. SPI (Stateful Packet Inspection) Firewall - A technology that inspects incoming packets of information before allowing them to enter the network. Spread Spectrum - Wideband radio frequency technique used for more reliable and secure data transmission. SSID (Service Set IDentifier) - Your wireless network's name. Static IP Address - A fixed address assigned to a computer or device that is connected to a network. Static Routing - Forwarding data in a network via a fixed path. Subnet Mask - An address code that determines the size of the network. Switch - 1. A data switch that connects computing devices to host computers, allowing a large number of devices to share a limited number of ports. 2. A device for making, breaking, or changing the connections in an electrical circuit. TCP (Transmission Control Protocol) - A network protocol for transmitting data that requires acknowledgement from the recipient of data sent. Appendix E: Glossary 75 Compact Wireless-G Internet Video Camera TCP/IP (Transmission Control Protocol/Internet Protocol) - A set of instructions PCs use to communicate over a network. Telnet - A user command and TCP/IP protocol used for accessing remote PCs. TFTP (Trivial File Transfer Protocol) - A version of the TCP/IP FTP protocol that has no directory or password capability. Throughput - The amount of data moved successfully from one node to another in a given time period. TKIP (Temporal Key Integrity Protocol) - a wireless encryption protocol that provides dynamic encryption keys for each packet transmitted. Topology - The physical layout of a network. TX Rate - Transmission Rate. UDP (User Datagram Protocol) - A network protocol for transmitting data that does not require acknowledgement from the recipient of the data that is sent. Upgrade - To replace existing software or firmware with a newer version. Upload - To transmit a file over a network. URL (Uniform Resource Locator) - The address of a file located on the Internet. VPN (Virtual Private Network) - A security measure to protect data as it leaves one network and goes to another over the Internet. WAN (Wide Area Network)- The Internet. WEP (Wired Equivalent Privacy) - A method of encrypting network data transmitted on a wireless network for greater security. WINIPCFG - A Windows 98 and Me utility that displays the IP address for a particular networking device. WLAN (Wireless Local Area Network) - A group of computers and associated devices that communicate with each other wirelessly. WPA (Wi-Fi Protected Access) - a wireless security protocol using TKIP (Temporal Key Integrity Protocol) encryption, which can be used in conjunction with a RADIUS server. Appendix E: Glossary 76 Compact Wireless-G Internet Video Camera Appendix F: Specifications Standards Ports Protocols Button Cabling Type Indicators IEEE 802.11b, IEEE 802.11g, IEEE 802.3, IEEE 802.3u One 10/100 Auto Crossover (MDI/MDI-X) port, Power port TCP/IP, HTTP, DHCP, NTP, SMTP, UPnP (Discovery only) One Reset Button RJ-45 1 x LED Security Features User Authentication, WEP/WPA-PSK, Motion Detection WEP Key Bits 64/128 Bit Image Sensor CMOS Lens Fixed Focus Resolution 320 x 240, 160 x 128 Relative Illumination 5.1 Lux Effective Focus 3 mm Sensitivity 1.0V/Lux-sec Field of View 61.48 degrees Compression Algorithm MPEG-4 Appendix F: Specifications 77 Compact Wireless-G Internet Video Camera Record File Format ASF Brightness Dimensions
(W x H x D) Unit Weight Power Auto/Manual Adjustment 3.54" x 4.02" x 1.46"
(90 mm x 102 mm x 37 mm) 0.29 lbs. (0.13 kg) 5V DC External Certifications FCC Operating Temp. 0C to 40C (32F to 104F) Storage Temp.
-10C to 70C (14F to 158F) Operating Humidity 10 to 85%
Storage Humidity 5 to 90%
Warranty 3-year limited Appendix F: Specifications 78 Compact Wireless-G Internet Video Camera Appendix G: Warranty Information LIMITED WARRANTY Linksys warrants to You that, for a period of three years (the Warranty Period), your Linksys Product will be substantially free of defects in materials and workmanship under normal use. Your exclusive remedy and Linksys' entire liability under this warranty will be for Linksys at its option to repair or replace the Product or refund Your purchase price less any rebates. This limited warranty extends only to the original purchaser. If the Product proves defective during the Warranty Period call Linksys Technical Support in order to obtain a Return Authorization Number, if applicable. BE SURE TO HAVE YOUR PROOF OF PURCHASE ON HAND WHEN CALLING. If You are requested to return the Product, mark the Return Authorization Number clearly on the outside of the package and include a copy of your original proof of purchase. RETURN REQUESTS CANNOT BE PROCESSED WITHOUT PROOF OF PURCHASE. You are responsible for shipping defective Products to Linksys. Linksys pays for UPS Ground shipping from Linksys back to You only. Customers located outside of the United States of America and Canada are responsible for all shipping and handling charges. ALL IMPLIED WARRANTIES AND CONDITIONS OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED TO THE DURATION OF THE WARRANTY PERIOD. ALL OTHER EXPRESS OR IMPLIED CONDITIONS, REPRESENTATIONS AND WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF NON-INFRINGEMENT, ARE DISCLAIMED. Some jurisdictions do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to You. This warranty gives You specific legal rights, and You may also have other rights which vary by jurisdiction. This warranty does not apply if the Product (a) has been altered, except by Linksys, (b) has not been installed, operated, repaired, or maintained in accordance with instructions supplied by Linksys, or (c) has been subjected to abnormal physical or electrical stress, misuse, negligence, or accident. In addition, due to the continual development of new techniques for intruding upon and attacking networks, Linksys does not warrant that the Product will be free of vulnerability to intrusion or attack. TO THE EXTENT NOT PROHIBITED BY LAW, IN NO EVENT WILL LINKSYS BE LIABLE FOR ANY LOST DATA, REVENUE OR PROFIT, OR FOR SPECIAL, INDIRECT, CONSEQUENTIAL, INCIDENTAL OR PUNITIVE DAMAGES, REGARDLESS OF THE THEORY OF LIABILITY (INCLUDING NEGLIGENCE), ARISING OUT OF OR RELATED TO THE USE OF OR INABILITY TO USE THE PRODUCT
(INCLUDING ANY SOFTWARE), EVEN IF LINKSYS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. IN NO EVENT WILL LINKSYS LIABILITY EXCEED THE AMOUNT PAID BY YOU FOR THE PRODUCT. The foregoing limitations will apply even if any warranty or remedy provided under this Agreement fails of its essential purpose. Some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to You. Please direct all inquiries to: Linksys, P.O. Box 18558, Irvine, CA 92623. Appendix G: Warranty Information 79 Compact Wireless-G Internet Video Camera Appendix H: Regulatory Information Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. IMPORTANT NOTE: FCC Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. To maintain compliance with FCC RF exposure compliance requirements, please avoid direct contact to the transmitting antenna during transmitting. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. We declare that the product is limited in CH1~CH11 by specified firmware controlled in the USA. Appendix H: Regulatory Information 80 Compact Wireless-G Internet Video Camera INDUSTRY CANADA The use of this device in a system operating either partially or completely outdoors may require the user to obtain a license for the system according to the Canadian regulations. This device complies with Industry Canada ICES-003 and RSS210 rules. IC Statement Operation is subject to the following two conditions:
1. This device may not cause interference and 2. This device must accept any interference, including interference that may cause undesired operation of the device. L'utilisation de ce priphrique dans un systme utilis partiellement ou totalement en extrieur peut conduire l'utilisateur l'obtention d'une licence pour ce systme conformment aux rgles en vigueur au Canada. Cet appareil est conforme aux normes NMB-003 et RSS210 d'Industrie Canada. Dclaration d'Industrie Canada Le fonctionnement est soumis aux conditions suivantes :
1. Ce priphrique ne doit pas causer d'interfrences;
2. Ce priphrique doit accepter toutes les interfrences reues, y compris celles qui risquent d'entraner un fonctionnement indsirable. SAFETY NOTICES Caution: To reduce the risk of fire, use only No.26 AWG or larger telecommunication line cord. Do not use this product near water, for example, in a wet basement or near a swimming pool. Avoid using this product during an electrical storm. There may be a remote risk of electric shock from lightning. Appendix H: Regulatory Information 81 Compact Wireless-G Internet Video Camera SOFTWARE LICENSE AGREEMENT THIS LICENSE AGREEMENT IS BETWEEN YOU AND CISCO-LINKSYS, LLC (Linksys). BY DOWNLOADING OR INSTALLING THE SOFTWARE, OR USING THE PRODUCT CONTAINING THE SOFTWARE, YOU ARE CONSENTING TO BE BOUND BY THIS AGREEMENT. IF YOU DO NOT AGREE TO ALL OF THESE TERMS, THEN YOU MAY NOT DOWNLOAD, INSTALL OR USE THE SOFTWARE. YOU MAY RETURN UNUSED SOFTWARE (OR, IF THE SOFTWARE IS SUPPLIED AS PART OF ANOTHER PRODUCT, THE UNUSED PRODUCT) FOR A FULL REFUND UP TO 30 DAYS AFTER ORIGINAL PURCHASE. License. Subject to the terms and conditions of this Agreement, Linksys grants the original end user purchaser of the Linksys product containing the Software (You) a nonexclusive license to use the Software solely as embedded in or (where authorized in the applicable documentation) for communication with such product. This license may not be sublicensed, and is not transferable except to a person or entity to whom you transfer ownership of the complete Linksys product containing the Software, provided you permanently transfer all rights under this Agreement and do not retain any full or partial copies of the Software, and the recipient agrees to the terms of this Agreement. Software includes, and this Agreement will apply to (a) the Linksys software provided in or with the applicable Linksys product, and (b) any upgrades, updates, bug fixes or modified versions (Upgrades) or backup copies of the Software supplied to You by Linksys or an authorized reseller, provided you already hold a valid license to the original software and have paid any applicable fee for the Upgrade. Protection of Information. The Software and documentation contain trade secrets and/or copyrighted materials of Linksys or its suppliers. You will not decompile, decrypt, reverse engineer or disassemble the Software
(except to the extent expressly permitted by law notwithstanding this provision), and will not disclose or make available such trade secrets or copyrighted material in any form to any third party. Title to Software and documentation will remain solely with Linksys. Open Source Software. The GPL source code incorporated into this product is available for free download at http://www.linksys.com/gpl. If You would like a copy of the GPL source code in this product on a CD, Linksys will copy and mail to You a CD with the code for $9.99 plus the cost of shipping upon request. Term and Termination. You may terminate this License at any time by destroying all copies of the Software and documentation. Your rights under this License will terminate immediately without notice from Linksys if You fail to comply with any provision of this Agreement. Limited Warranty. The warranty terms and period specified in the applicable Linksys Product User Guide shall also apply to the Software. Disclaimer of Liabilities. IN NO EVENT WILL LINKSYS BE LIABLE FOR ANY LOST DATA, REVENUE OR PROFIT, OR FOR SPECIAL, INDIRECT, CONSEQUENTIAL, INCIDENTAL OR PUNITIVE DAMAGES, REGARDLESS OF CAUSE Appendix H: Regulatory Information 82 Compact Wireless-G Internet Video Camera
(INCLUDING NEGLIGENCE), ARISING OUT OF OR RELATED TO THE USE OF OR INABILITY TO USE THE SOFTWARE, EVEN IF LINKSYS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. IN NO EVENT WILL LINKSYS'
LIABILITY EXCEED THE AMOUNT PAID BY YOU FOR THE PRODUCT. The foregoing limitations will apply even if any warranty or remedy under this Agreement fails of its essential purpose. Some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to You. Export. Software, including technical data, may be subject to U.S. export control laws and regulations and/or export or import regulations in other countries. You agree to comply strictly with all such laws and regulations. U.S. Government Users. The Software and documentation qualify as commercial items as defined at 48 C.F.R. 2.101 and 48 C.F.R. 12.212. All Government users acquire the Software and documentation with only those rights herein that apply to non-governmental customers. General Terms. This Agreement will be governed by and construed in accordance with the laws of the State of California, without reference to conflict of laws principles. The United Nations Convention on Contracts for the International Sale of Goods will not apply. If any portion of this Agreement is found to be void or unenforceable, the remaining provisions will remain in full force and effect. This Agreement constitutes the entire agreement between the parties with respect to the Software and supersedes any conflicting or additional terms contained in any purchase order or elsewhere. Appendix H: Regulatory Information 83 Compact Wireless-G Internet Video Camera Appendix I: Contact Information Need to contact Linksys?
Visit us online for information on the latest products and updates to your existing products at:
Can't find information about a product you want to buy on the web? Do you want to know more about networking with Linksys products? Give our advice line a call at:
Or fax your request in to:
If you experience problems with any Linksys product, you can call us at:
Don't wish to call? You can e-mail us at:
If any Linksys product proves defective during its warranty period, you can call the Linksys Return Merchandise Authorization department for obtaining a Return Authorization Number at:
(Details on Warranty and RMA issues can be found in the Warranty Information section in this Guide.) http://www.linksys.com or ftp.linksys.com 800-546-5797 (LINKSYS) 949-823-3002 800-326-7114 support@linksys.com 949-823-3000 Appendix I: Contact Information 84
frequency | equipment class | purpose | ||
---|---|---|---|---|
1 | 2005-10-25 | 2412 ~ 2462 | DTS - Digital Transmission System | Original Equipment |
app s | Applicant Information | |||||
---|---|---|---|---|---|---|
1 | Effective |
2005-10-25
|
||||
1 | Applicant's complete, legal business name |
LINKSYS LLC
|
||||
1 | FCC Registration Number (FRN) |
0008067837
|
||||
1 | Physical Address |
121 Theory Drive
|
||||
1 |
Irvine, California 92617
|
|||||
1 |
United States
|
|||||
app s | TCB Information | |||||
1 | TCB Application Email Address |
s******@curtis-straus.com
|
||||
1 | TCB Scope |
A4: UNII devices & low power transmitters using spread spectrum techniques
|
||||
app s | FCC ID | |||||
1 | Grantee Code |
Q87
|
||||
1 | Equipment Product Code |
WVC54GC
|
||||
app s | Person at the applicant's address to receive grant or for contact | |||||
1 | Name |
J****** H********
|
||||
1 | Title |
Regulatory Compliance Manager
|
||||
1 | Telephone Number |
949-2********
|
||||
1 | Fax Number |
949-2********
|
||||
1 |
j******@belkin.com
|
|||||
app s | Technical Contact | |||||
1 | Firm Name |
Advance Data Technology Corporation (Hwa Ya)
|
||||
1 | Name |
C****** C******
|
||||
1 | Physical Address |
No. 19, Hwa Ya 2nd Rd., Kwei Shan Hsiang
|
||||
1 |
Taoyuan Hsien, 333
|
|||||
1 |
Taiwan
|
|||||
1 | Telephone Number |
886-3******** Extension:
|
||||
1 | Fax Number |
886-3********
|
||||
1 |
C******@adt.com.tw
|
|||||
app s | Non Technical Contact | |||||
1 | Firm Name |
Advance Data Technology Corporation
|
||||
1 | Name |
S******** H****
|
||||
1 | Physical Address |
No. 19, Hwa Ya 2nd Rd., Kwei Shan Hsiang
|
||||
1 |
Taoyuan Hsien, 333
|
|||||
1 |
Taiwan
|
|||||
1 | Telephone Number |
886-3******** Extension:
|
||||
1 | Fax Number |
886-3********
|
||||
1 |
s******@adt.com.tw
|
|||||
app s | Confidentiality (long or short term) | |||||
1 | Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | Yes | ||||
1 | Long-Term Confidentiality Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | No | ||||
if no date is supplied, the release date will be set to 45 calendar days past the date of grant. | ||||||
app s | Cognitive Radio & Software Defined Radio, Class, etc | |||||
1 | Is this application for software defined/cognitive radio authorization? | No | ||||
1 | Equipment Class | DTS - Digital Transmission System | ||||
1 | Description of product as it is marketed: (NOTE: This text will appear below the equipment class on the grant) | Compact Wireless-G Internet Video Camera | ||||
1 | Related OET KnowledgeDataBase Inquiry: Is there a KDB inquiry associated with this application? | No | ||||
1 | Modular Equipment Type | Does not apply | ||||
1 | Purpose / Application is for | Original Equipment | ||||
1 | Composite Equipment: Is the equipment in this application a composite device subject to an additional equipment authorization? | No | ||||
1 | Related Equipment: Is the equipment in this application part of a system that operates with, or is marketed with, another device that requires an equipment authorization? | No | ||||
1 | Grant Comments | Output power listed is conducted. The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. End -users and installers must be provided with antenna installation and transmitter operating conditions for satisfying RF exposure compliance. | ||||
1 | Is there an equipment authorization waiver associated with this application? | No | ||||
1 | If there is an equipment authorization waiver associated with this application, has the associated waiver been approved and all information uploaded? | No | ||||
app s | Test Firm Name and Contact Information | |||||
1 | Firm Name |
Bureau Veritas CPS (H.K.) Ltd. Taoyuan Branch
|
||||
1 | Name |
R******** C********
|
||||
1 | Telephone Number |
886-3******** Extension:
|
||||
1 | Fax Number |
886-3********
|
||||
1 |
r******@tw.bureauveritas.com
|
|||||
Equipment Specifications | |||||||||||||||||||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
1 | 1 | 15C | 2412.00000000 | 2462.00000000 | 0.0800000 |
some individual PII (Personally Identifiable Information) available on the public forms may be redacted, original source may include additional details
This product uses the FCC Data API but is not endorsed or certified by the FCC