FCC ID: Q87-EA6350 Linksys EA6350 Smart Wi-Fi Router

Product Overview EA6350 Top view Indicator lightStays on steadily while power is connected and following a successful Wi-Fi Protected Setup connection. Flashes or pulses slowly during bootup, during firmware upgrades, and during a Wi-Fi Protected Setup connection. Flashes quickly when there is a Wi-Fi Protected Setup error. Back view Adjustable Antenna ports The included 2 adjustable external antennas should be connected to the router before powering it on. Twist the antenna connector clockwise onto the port on the router. NOTE For best performance, position the side antennas at a 30 angle as shown in the picture on the left. Wi-Fi Protected Setup button Press to easily configure wireless security on Wi-Fi Protected Setup-enabled network devices. USB portConnect and share a USB drive or a USB printer. Ethernet portsConnect Ethernet cables to the blue gigabit (10/100/1000) ports and to wired Ethernet network devices. NOTE For best performance, use CAT5E or higher rated cables on the Ethernet ports. Internet portConnect an Ethernet cable to this yellow port and to your modem. Reset buttonPress and hold for 10 seconds (until the port lights flash at the same time) to reset the router to its factory defaults. You can also restore the defaults using Linksys Smart Wi-Fi. Power portConnect the included AC power adapter. Power buttonPress | (on) to turn on the router. Setting Up Your EA-Series Router Where to find more help Linksys.com/support (documentation, downloads, FAQs, technical support, live chat, forums) Linksys Smart Wi-Fi help (connect to Linksys Smart Wi-Fi, then click Help at the top of the screen) How to install your router To install your router:

If replacing an existing router, disconnect it. Power on your new router. Connect the Internet cable from your modem to the yellow Internet port on your router. Wait until the power light on the front of the router is solid. Connect to the secure wireless name shown in the Quick Start Guide that came with your router. (You can change the network name and password later during router setup.) If you need help connecting to the network, refer to your device documentation CD. Note: You will not have Internet access until router setup is complete. Open a web browser and follow the instructions to complete your routers setup. If instructions do not appear in the web browser, enter linksyssmartwifi.com in the browsers address bar. At the end of setup, follow the on-screen instructions to set up your Linksys Smart Wi-Fi account. Use Linksys Smart Wi-Fi to easily manage your routers settings, such as:

Change your routers name and password Set up guest access Configure parental controls Connect devices to your network Test your Internet connection speed NOTE:

As part of Linksys Smart Wi-Fi account setup, you will be sent a verification e-mail. Make sure that you open the e-mail from Linksys and click the provided link. How to connect to Linksys Smart Wi-Fi You can use Linksys Smart Wi-Fi to configure your router from any computer that has an Internet connection. To open Linksys Smart Wi-Fi:

Click the Linksys Smart Wi-Fi icon on your desktop.

- OR -

Open a web browser and go to www.linksyssmartwifi.com. Enter the e-mail address and password you set up earlierand click Log in. How to change router settings Use Linksys Smart Wi-Fi to change settings on your router and set up special features such as parental controls and guest access. NOTE:

For additional help on any menu, click Help at the top of the screen. To change router settings:

Open Linksys Smart Wi-Fi and log in to your account. In the menu on the left, click an option:

Device List lets you display and manage all network devices connected to your router. You can view devices on your main network and your guest network, disconnect the devices, or display information about each device. Guest Access lets you configure a network so guests can access the Internet, but not all of your network resources. Parental Controls let you block web sites and set Internet access times. Media Prioritization lets you set which devices and applications have top priority for your network traffic. Speed Test lets you test your networks Internet connection speed. USB Storage lets you access an attached USB drive (not included) and set up file sharing, a media server, and FTP access.

(Available only on routers with USB ports.) Connectivity lets you configure basic and advanced network settings. Troubleshooting lets you diagnose problems with your router and check the status of the network. Wireless lets you configure your routers wireless network. You can change the security mode, password, MAC filtering, and connect devices using Wi-Fi Protected Setup. Security lets you configure your routers wireless security. You can set up the firewall, VPN settings, and make custom settings for applications and games. Troubleshooting This chapter can help you solve common setup issues and connect to the Internet. You can find more help from our award-winning customer at linksys.com/support. support Your router was not successfully set up If Linksys Smart Wi-Fi did not complete the setup, you can try the following:

Press and hold the Reset button on your router with a paperclip or pin until the LED starts flashing (about 10 seconds), then install the router again. Temporarily disable your computers firewall (see the security softwares instructions for help), and install the router again. If you have another computer, use that computer to install the router again. Your routers appearance may vary Windows XP Service Pack update On Windows XP computers, Linksys Smart Wi-Fi requires Service Pack 3. If the currently installed Service Pack is older than version 3, you need to download and install Service Pack 3. TIP To temporarily connect to the Internet and download the required Service Pack, you can use the included Ethernet cable to connect your computer directly to your modem. To install Service Pack 3:

Connect to the Microsoft Update website (update.microsoft.com/windowsupdate). Follow the instructions on the website or contact Microsoft if you need further help. After downloading and installing Service Pack 3, install the router again. Your Internet cable is not plugged in message If you get a Your Internet cable is not plugged in message when trying to set up your router, follow these troubleshooting steps. To fix the problem:

Make sure that an Ethernet or Internet cable (or a cable like the one supplied with your router) is securely connected to the yellow Internet port on the back of the router and to the appropriate port on your modem. This port on the modem is usually labeled Ethernet, but may be named Internet or WAN. Back view of router Back view of cable modem Back view of DSL modem Make sure that your modem is connected to power and is turned on. If it has a power switch, make sure that it is set to the ON or l position. If your Internet service is cable, verify that the cable modems CABLE port is connected to the coaxial cable provided by your ISP. Or, if your Internet service is DSL, make sure that the DSL phone line is connected to the modems DSL port. If your computer was previously connected to your modem with a USB cable, disconnect the USB cable. Install the router again. Cannot access your router message If you cannot access your router because your computer is not connected to your network, follow these troubleshooting steps. To access your router, you must be connected to your own network. If you currently have wireless Internet access, the problem may be that you have accidentally connected to a different wireless network. To fix the problem on Windows computers:

On your Windows desktop, right-click the wireless icon in the system tray. The icon can differ depending on your version of Windows. Click View Available Wireless Networks. A list of available networks appears. Click your own network name, and click Connect. In the example below, the computer was connected to another wireless network named JimsRouter. The name of the Linksys E-Series network, BronzeEagle in this example, is shown selected. If you are prompted to enter a network key, type your password (Security Key) into the Network key and Confirm network key fields, then click Connect. Your computer will connect to the network, and you should be able to access the router. To fix the problem on Mac computers:

In the menu bar across the top of the screen, click the Wi-Fi icon. A list of wireless networks appears. Linksys Smart Wi-Fi has automatically assigned your network a name. In the example below, the computer was connected to another wireless network named JimsRouter. The name of the Linksys E-

Series network, BronzeEagle in this example, is shown selected. Click the wireless network name of your Linksys E-Series router (BronzeEagle in the example). Type your wireless network password (Security Key) into the Password field, and click OK. Specifications Linksys EA6350 Model Name Description Linksys Smart Wi-Fi Router AC 1200 Dual-Band AC Router with Gigabit and 1USB Model Number EA6350 Switch Port Speed 10/100/1000 Mbps (Gigabit Ethernet) Radio Frequency 2.4 and 5 GHz

# of Antennas 2 external adjustable antennas Ports Buttons LEDs UPnP Power, USB (1), Internet, Ethernet (1-4), R-SMA antenna (2) Reset, Wi-Fi Protected Setup, power Top panel: Power Back panel: Internet, Ethernet (1-4) Supported Security Features WEP, WPA2, RADIUS Security Key Bits Up to 128-bit encryption Storage File System Support FAT, NTFS, and HFS+

Browser Support Internet Explorer 8 or higher, Firefox 4 or higher, Google Chrome 10 or higher, and Safari 4 or higher Environmental Dimensions Unit Weight Power Certifications 10.8 x 1.58 x 7.25

(256 x 40 x 184 mm) 17.67 oz (501 g) 12V, 2A FCC, IC, CE, Wi-Fi a/b/g/n/ac, Windows 7, Windows 8, DLNA Operating Temp. 32 to 104F (0 to 40C) Storage Temp.

-4 to 140F (-20 to 60C) Operating Humidity Storage Humidity NOTES 10 to 80% relative humidity, non-condensing 5 to 90% non-condensing For regulatory, warranty, and safety information, see the CD that came with your router or go to Linksys.com/support. Specifications are subject to change without notice. Maximum performance derived from IEEE Standard 802.11 specifications. Actual performance can vary, including lower wireless network capacity, data throughput rate, range and coverage. Performance depends on many factors, conditions and variables, including distance from the access point, volume of network traffic, building materials and construction, operating system used, mix of wireless products used, interference and other adverse conditions. Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. For product available in the USA/Canada market, only channel 1~11 can be operated. Selection of other channels is not possible. This device and it's antennas(s) must not be co-located or operating in conjunction with any other antenna or transmitter except in accordance with FCC multi-transmitter product procedures. This device is going to be operated in 5.15~5.25GHz frequency range, it is restricted in indoor environment only. IMPORTANT NOTE:

FCC Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator

& your body. This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. For product available in the USA/Canada market, only channel 1~11 can be operated. Selection of other channels is not possible. Pour les produits disponibles aux tats-Unis / Canada du march, seul le canal 1 11 peuvent tre exploits. Slection d'autres canaux n'est pas possible. This device and it's antennas(s) must not be co-located or operating in conjunction with any other antenna or transmitter except in accordance with IC multi-transmitter product procedures. Cet appareil et son antenne (s) ne doit pas tre co-localiss ou fonctionnement en association avec une autre antenne ou transmetteur. The device for the band 5150-5250 MHz is only for indoor usage to reduce potential for harmful interference to co-channel mobile satellite systems. les dispositifs fonctionnant dans la bande 5150-5250 MHz sont rservs uniquement pour une utilisation lintrieur afin de rduire les risques de brouillage prjudiciable aux systmes de satellites mobiles utilisant les mmes canaux;

IC Radiation Exposure Statement:

This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Cet quipement est conforme aux limites d'exposition aux rayonnements IC tablies pour un environnement non contrl. Cet quipement doit tre install et utilis avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps.

Report No.: 421018 APPENDIX A. Photographs of EUT SPORTON International Inc. TEL : 886-3-327-3456 FAX : 886-3-327-0973 PAGE NUMBER : A1 OF A10 ISSUED DATE

: Mar. 18, 2014 Report No.: 421018 SPORTON International Inc. TEL : 886-3-327-3456 FAX : 886-3-327-0973 PAGE NUMBER : A2 OF A10 ISSUED DATE

: Mar. 18, 2014 Report No.: 421018 SPORTON International Inc. TEL : 886-3-327-3456 FAX : 886-3-327-0973 PAGE NUMBER : A3 OF A10 ISSUED DATE

: Mar. 18, 2014 Report No.: 421018 SPORTON International Inc. TEL : 886-3-327-3456 FAX : 886-3-327-0973 PAGE NUMBER : A4 OF A10 ISSUED DATE

: Mar. 18, 2014 Report No.: 421018 SPORTON International Inc. TEL : 886-3-327-3456 FAX : 886-3-327-0973 PAGE NUMBER : A5 OF A10 ISSUED DATE

: Mar. 18, 2014 Report No.: 421018 SPORTON International Inc. TEL : 886-3-327-3456 FAX : 886-3-327-0973 PAGE NUMBER : A6 OF A10 ISSUED DATE

: Mar. 18, 2014 Report No.: 421018 SPORTON International Inc. TEL : 886-3-327-3456 FAX : 886-3-327-0973 PAGE NUMBER : A7 OF A10 ISSUED DATE

: Mar. 18, 2014 Report No.: 421018 SPORTON International Inc. TEL : 886-3-327-3456 FAX : 886-3-327-0973 PAGE NUMBER : A8 OF A10 ISSUED DATE

: Mar. 18, 2014 Report No.: 421018 SPORTON International Inc. TEL : 886-3-327-3456 FAX : 886-3-327-0973 PAGE NUMBER : A9 OF A10 ISSUED DATE

: Mar. 18, 2014 Report No.: 421018 SPORTON International Inc. TEL : 886-3-327-3456 FAX : 886-3-327-0973 PAGE NUMBER : A10 OF A10 ISSUED DATE

: Mar. 18, 2014

Report No.: 421018 APPENDIX A. Photographs of EUT SPORTON International Inc. TEL : 886-3-327-3456 FAX : 886-3-327-0973 PAGE NUMBER : A1 OF A7 ISSUED DATE

: Mar. 18, 2014 Report No.: 421018 SPORTON International Inc. TEL : 886-3-327-3456 FAX : 886-3-327-0973 PAGE NUMBER : A2 OF A7 ISSUED DATE

: Mar. 18, 2014 Report No.: 421018 SPORTON International Inc. TEL : 886-3-327-3456 FAX : 886-3-327-0973 PAGE NUMBER : A3 OF A7 ISSUED DATE

: Mar. 18, 2014 Report No.: 421018 Adapter 1 (Fixed plug) Brand: APD Model: WA-24E12FU SPORTON International Inc. TEL : 886-3-327-3456 FAX : 886-3-327-0973 PAGE NUMBER : A4 OF A7 ISSUED DATE

: Mar. 18, 2014 Report No.: 421018 Adapter 2 (Interchangeable plug) Brand: APD Model: WA-24E12 SPORTON International Inc. TEL : 886-3-327-3456 FAX : 886-3-327-0973 PAGE NUMBER : A5 OF A7 ISSUED DATE

: Mar. 18, 2014 Report No.: 421018 SPORTON International Inc. TEL : 886-3-327-3456 FAX : 886-3-327-0973 PAGE NUMBER : A6 OF A7 ISSUED DATE

: Mar. 18, 2014 Plug (Only for Adapter 2) Report No.: 421018 SPORTON International Inc. TEL : 886-3-327-3456 FAX : 886-3-327-0973 PAGE NUMBER : A7 OF A7 ISSUED DATE

: Mar. 18, 2014

ARTWORK_WG9116FAC22 1-88 R01 01/27/2014 Bel_Chan

&

EA6350 EA6350 6 ARTWORK_WG9116FAC22 1-88 R01 01/23/2014 Bel_Chan

&

5 5 5 7.53 mm 20.00 mm 7.53 mm m m 0 0

. 3 0.99 mm m m 0 0

. 8 1 2.86 mm 5 5 5 m m 0 8

. 4 6 m m 5 7

. 8

telltn Linksys LLC 131 Theory Drive, Irvine, CA 92617, USA Tel: 949-842-0744 / Fax: 949-823-3002 Confidential Letter Date: 2014/2/18 Federal Communications Commission Authorization and Evaluation Division FCC ID : Q87-EA6350 Confidentiality Request Pursuant to Sections 0.457 and 0.459 of the Commission's Rules, the Applicant Hereby requests confidential treatment of information accomparting this Application As outlined below:

1. Block Diagram 2. Circuit Diagram 3. Operational Description The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. The Applicant understands that pursuant to Rule 0.457, disclosure of this Application and alll accompanying documentation will not be made before the date of the Grant for this application Sincerely, Applicant's company name Linksys LLC Applicant's company address 131 Theory Drive, Irvine, CA 92617, USA Name and Job Title nis / Senior Manager, Regulatory Compliance E-Mail darrell.tennis@belkin.com 949-842-0744

Linksys LLC 131 Theory Drive, Irvine, CA 92617, USA Tel: 949-842-0744 / Fax: 949-823-3002 Power of Attorney Drei Ae PAls) Dear Sir,

| hereby have entrusted the following person to be a proxy regarding application for Type Certification. by eee M Clare Litem Address : No.8, Lane 724, Bo-ai St., Jnubei City, HsinChu County 302, Taiwan, R.O.C Name : Leo Huang Job Title : Manager e-mail : Leohuang@sporton.com.tw lam therefore responsible for the contents of the application. Brand name and model type of the specified radio equipment: Linksys / EA6350 FCC ID: Q87-EA6350 Product name: Linksys Smart Wi-Fi Router AC 1200 FCC Grantee contact person information. Applicant's company name > Linksys LLC Applicant's company address : 131 Theory Drive, Irvine, CA 92617, USA Signature Name and Job Title DYelic=) | Kea! nior Manager, Regulatory Compliance E-Mail ran ns darrell.tennis@belkin.com 9A9-849-0744