all | frequencies |
|
|
|
|
exhibits | applications |
---|---|---|---|---|---|---|---|
manuals |
app s | submitted / available | |||||||
---|---|---|---|---|---|---|---|---|
1 |
|
Manual Part 1 | Users Manual | 2.79 MiB | April 05 2007 | |||
1 |
|
Manual Part 2 | Users Manual | 2.88 MiB | April 05 2007 | |||
1 |
|
Manual Part 3 | Users Manual | 1.71 MiB | April 05 2007 | |||
1 |
|
Manual Part 4 | Users Manual | 1.29 MiB | April 05 2007 | |||
1 | Attestation Statements | April 05 2007 | ||||||
1 | Cover Letter(s) | April 05 2007 | ||||||
1 | Cover Letter(s) | April 05 2007 | ||||||
1 | External Photos | April 05 2007 | ||||||
1 | Internal Photos | April 05 2007 | ||||||
1 | ID Label/Location Info | April 05 2007 | ||||||
1 | ID Label/Location Info | April 05 2007 | ||||||
1 | Operational Description | April 05 2007 | ||||||
1 | Attestation Statements | April 05 2007 | ||||||
1 | RF Exposure Info | April 05 2007 | ||||||
1 | Test Report | April 05 2007 | ||||||
1 | Test Setup Photos | April 05 2007 |
1 | Manual Part 1 | Users Manual | 2.79 MiB | April 05 2007 |
USER GUIDE BUSINESS SERIES Wireless-G Exterior Access Point with Power Over Ethernet Model: WAP200E About This Guide About Ths Gude Icon Descriptions While reading through the User Guide you may encounter various icons designed to call attention to a specific item. Below is a description of these icons:
NOTE: This check mark indicates that there is a note of interest and is something that you should pay special attention to while using the product. WARNING: This exclamation point indicates that there is a caution or warning and it is something that could damage your property or product. WEB: This globe icon indicates a noteworthy website address or e-mail address. Online Resources Most web browsers allow you to enter the web address without adding the http:// in front of the address. This User Guide will refer to websites without including http://
in front of the address. Some older web browsers may require you to add it. Resource Linksys Webste www.linksys.com Linksys International www.linksys.com/international Glossary www.linksys.com/glossary Network Security www.linksys.com/security Copyright and Trademarks Specifications are subject to change without notice. Linksys is a registered trademark or trademark of Cisco Systems, Inc. and/or its affiliates in the U.S. and certain other countries. Copyright 2007 Cisco Systems, Inc. All rights reserved. Other brands and product names are trademarks or registered trademarks of their respective holders. Wreless-G Exteror Access Pont wth Power Over Ethernet
Chapter 4: Installation Chapter 3: Product Overview Table of Contents Chapter 1: Introduction 1 Chapter 2: Planning Your Wireless Network 2 Network Topology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Roaming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Network Layout. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Example of a Simple Wireless Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 3 Front Panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Bottom Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Top Panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Back Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 The Antenna Pattern . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 6 Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Personal Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Installation Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 External Antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Installation Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 8 Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Accessing the Web-Based Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Navigating the Web-Based Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Wireless . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 AP Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Administration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 10 Web-Based Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10 Setup > Basic Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10 Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10 Network Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10 Setup > Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11 Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11 Wireless > Basic Wireless Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11 Basic Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11 Wireless > Wireless Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12 Wireless Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12 Wireless > Wireless Connection Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15 Chapter 5: Quick Configuration Overview Chapter 6: Advanced Configuration Wreless-G Exteror Access Pont wth Power Over Ethernet
Table of Contents Wireless Connection Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15 Connection Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15 Connection Control List. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16 Wireless > Advanced Wireless Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16 Advanced Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16 Wireless > VLAN & QoS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17 VLAN. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17 QoS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17 AP Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18 Administration > Management. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19 AP Password . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19 Web Access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19 SNMP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19 Administration > Log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20 Log. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20 Administration > Factory Default . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21 Factory Default . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21 Administration > Firmware Upgrade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21 Firmware Upgrade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21 Administration > Reboot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22 Reboot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22 Administration > Config Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22 Config Management. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22 Status > Local Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22 Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22 Local Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22 Status > Wireless . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23 Wireless Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23 Status > System Performance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23 System Performance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23 25 Appendix A: Troubleshooting Appendix B: Wireless Security Checklist 28 General Network Security Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28 Additional Security Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28 29 Appendix C: Glossary Appendix D: Specifications 33 Appendix E: Warranty and Regulatory Information 35 Limited Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35 FCC Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35 Wreless-G Exteror Access Pont wth Power Over Ethernet
Table of Contents FCC Radiation Exposure Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36 Safety Notices. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36 Industry Canada Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36 Industry Canada Radiation Exposure Statement: . . . . . . . . . . . . . . . . . . . . . . .36 Avis dIndustrie Canada. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36 Avis dIndustrie Canada concernant lexposition aux radiofrquences :. . . . . . . . .36 User Information for Consumer Products Covered by EU Directive 2002/96/EC on Waste Electric and Electronic Equipment (WEEE) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37 41 Appendix F: Contact Information Wreless-G Exteror Access Pont wth Power Over Ethernet
v Introduction Chapter
Chapter :
Introducton Thank you for choosing the Wireless-G Exterior Access Point with Power Over Ethernet. The Linksys Wireless-G Exterior Access Point with Power Over Ethernet lets you connect Wireless-G (802.11g) or Wireless-B (802.11b) devices to your wired network so you can add PCs to the network with no cabling hassle. This weather-proof Access Point creates a wireless bubble in exterior spaces, like patios, pool areas, and outdoor cafs. Power over Ethernet support makes it easy to install, and you can create multiple SSIDs that connect to individual VLANs to keep your traffic separated. Its also perfect for use as a bridge, a kind of cable-less cable to connect remote areas together. Maybe your warehouse is in a separate building from your offices. Or maybe you need to connect the separate buildings of a college campus. With one Wireless-G Exterior Access Point on each building, youre connected with no cable to run. The exterior-rated case protects the access point, and contains an internal antenna. To protect your data and privacy, the Wireless-G Exterior Access Point with Power Over Ethernet supports both Wired Equivalent Privacy (WEP) and the industrial-strength wireless security of Wi-Fi Protected Access (WPA), encoding all your wireless transmissions with powerful encryption. The MAC Address filter lets you decide exactly who has access to your wireless network, and advanced logging keeps you appraised. Configuration is a snap with the web browser-based configuration utility. The Linksys Wireless-G Exterior Access Point with Power Over Ethernet is the best way to add wireless access to the outdoor areas of your home or business. Wreless-G Exteror Access Pont wth Power Over Ethernet
Chapter
Planning Your Wireless Network Chapter :
Plannng Your Wreless Network Network Topology A wireless network is a group of computers, each equipped with one or more wireless adapters. Computers in a wireless network must be configured to share the same radio channel to talk to each other. Several PCs equipped with wireless cards or adapters can communicate with each other to form an ad-hoc network without the use of an access point. Linksys wireless adapters also provide access to a wired network when using an access point or wireless router. An integrated wireless and wired network is called an infrastructure network. Each wireless PC in an infrastructure network can talk to any computer in a wired or wireless network via the access point or wireless router. An infrastructure configuration extends the accessibility of a wireless PC to a wired network, and may double the effective wireless transmission range for two wireless adapter PCs. Since an access point is able to forward data within a network, the effective transmission range in an infrastructure network may be doubled (depending on antenna characteristics). Roaming Infrastructure mode also supports roaming capabilities for mobile users. Roaming means that you can move your wireless PC within your network and the access points will pick up the wireless PCs signal, providing that they both share the same wireless channel, SSID, and wireless security settings. Before you consider roaming, choose a feasible radio channel and optimum access point position. Proper access point positioning combined with a clear radio signal will greatly enhance performance. NOTE: Spanning Tree Protocol should be disabled on the switches connecting to the APs to allow roaming to work without disruption. Network Layout The Access Point has been designed for use with 802.11g and 802.11b products, such as the Notebook Adapters for your laptop computers, PCI Adapters for your desktop PCs, and USB Adapters. These wireless products can also communicate with a 802.11g or 802.11b Wireless PrintServer. To link your wired network with your wireless network, connect the Access Points Ethernet network port to any switch or router with Power over Ethernet (PoE)or a PoE injector, such as the Linksys WAPPOE or WAPPOE12. NOTE: 12 VDC on WAPPOE12 is for the splitter output. Both PoE Injectors provide 48 VDC power output. Go to the Linksys website at www.lnksys.com for more information about wireless products. Example of a Simple Wireless Network Example of Smple Wreless Network The above diagram shows a typical infrastructure wireless network setup. The Wireless Access Points are connecting to a Linksys switch that provides power to the Access Points. Each Access Point can connect multiple wireless devices to the network. This network will provide connectivity among wireless network devices and PCs that have a wired connection to the switch. The switch then can connect to a router that can connect to an ISP for Internet access. Wreless-G Exteror Access Pont wth Power Over Ethernet
Chapter
Product Overview Chapter :
Product Overvew Bottom Panel The Ethernet network port is located on the bottom panel of the Access Point. Front Panel The Access Points LEDs, where information about network activity is displayed, are located on the front panel. Bottom Panel Ethernet network port The Ethernet network port connects to Ethernet network devices, such as a switch or router. The Access Point is powered using Power Over Ethernet. If the switch or router doesnt support Power Over Ethernet, then a Power Over Ethernet Injector must be installed. Top Panel The antenna port is located on the top panel of the Access Point. Top Panel Antenna Port The Access Point has built-in, 1x2 MIMO 9dBi directional antennas. It also has a reverse polarity female N-type antenna port for an optional, high-gain external antenna such as the HGA9N. One of the two internal antennas will be disabled automatically when an external antenna is connected. Front Panel Power (Green) The Power LED lights up when the Access Point is powered on. Wred (Green) The Wired LED lights up when the Access Point is successfully connected to a device through the Ethernet network port. If the Wired LED is flashing, the Access Point is actively sending to or receiving data from one of the devices over the Ethernet network port. Wreless (Green) The Wireless LED lights up when the wireless module is active on the Access Point. If the Wireless LED is flashing, the Access Point is actively sending to or receiving data from a wireless device. Wreless-G Exteror Access Pont wth Power Over Ethernet
Chapter
Product Overview Back Panel The Access Points Reset button and ground are located on the back panel. Reset button The Antenna Pattern The Wireless-G Exterior Access Point uses 1X2 MIMO (1Tx, 2Rx) so it has two built-in antennas. The right antenna is the main antenna for Tx traffic. When an external antenna is attached, the right antenna is disabled and the external antenna is used for Tx traffic. Currently, only the HGA9N
(9dBi omni-directional antenna) is compatible with the Wireless-G Exterior Access Point. Ground Back Panel Right Antenna Pattern 3dB BW: 50 degree, peak gain: 6.3 dBi Reset Button There are two ways to Reset the Access Points factory defaults. Either press the Reset button, for approximately ten seconds, or restore the defaults using the Access Points web-based utility. IMPORTANT: Resetting the Access Point will erase all of your settings (including wireless security, IP address, and power output) and replace them with the factory defaults. Do not reset the Access Point if you want to retain these settings. Ground Before you mount the Access Point, you must ground the Access Point (to a large piece of metal) as a precaution against electric shock. Left Antenna Pattern 3dB BW: 63 degree, peak gain: 4.9 dBi Wreless-G Exteror Access Pont wth Power Over Ethernet
Chapter
Product Overview Radio Coverage of the Access Point to Client Devices When using the Access Point to connect client devices, adjust it so the client devices are on the same horizontal plane as the Access Point and within a 3dB angle of 47 degrees. This will ensure the strongest signal and maximum reach. If the Access Point is used inside a building, put it in a corner of the building for maximum coverage. Access Point to Access Point (bridging) Radio Coverage If the Access Point is used as a bridge or repeater, adjust the Access Points so they face each other, this will ensure the strongest signal and maximum reach. Make sure that the orientation of the two Directional Antennas is the same. The radio wave is polarized so a 90 degree rotation will result in no received power. Due to its directional characteristics, the internal antenna is ideal for point-to-point bridge mode or the spoke side of point-to-multipoint bridge mode. An external omni-directional antenna (e.g. HGA9N) is recommended for repeater mode applications. Wreless-G Exteror Access Pont wth Power Over Ethernet
Chapter
Chapter :
Installaton Overview This chapter explains how to mount and connect the Access Point. Depending on your application, you might want to set up the IP address of the device first before mounting the device. Refer to Chapter 5: Quick Configuration Overview. Personal Installation This product should be installed by a qualified installation professional with RF and related rule knowledge. General users should not attempt to install this product or modify the settings. Installation Location The product should be installed in a location where the radiating antenna is at least 20 cm from anyone under normal operating conditions. This is required to meet regulatory RF exposure requirements. External Antenna Use only antennas approved by Linksys. Antennas that have not been approved by Linksys may produce unwanted spurious or excessive RF transmitting power, this may lead to violation of FCC limitations and is prohibited. Installation Procedure Follow the Hardware Installation instructions for details on installing this product. WARNING: Please carefully select the installation position and make sure that the final output power does not exceed the limit defined in US Rule CFR 47 Part 15, section 15.247 and 15.407. Violation of the rule could lead to serious federal penalties. Hardware Installation 1. Locate an optimum location on a wall for the Access Point. Refer to the antenna pattern in Chapter 3:
Product Overview to adjust the angle of the Access Point for your application. Installation 2. Using the mounting plate as a template, mark the locations of the two wall-mount slots that are on the bottom of the mounting plate. Then, install a screw into each location. Mark the Locations of the Two Wall-Mount Slots 3. Use four screws (included with the Access Point) to attach the mounting plate to the back panel of the Access Point. Attach the Mounting Plate 4. Connect the included Category 5e Ethernet network cable to the Ethernet network port of the Access Point. Wreless-G Exteror Access Pont wth Power Over Ethernet
Chapter
Installation Then, screw the connector cap tightly onto the port, so the Access Point has a water-resistant seal. 5. If you want to connect an optional, high-gain external antenna, remove the cap that protects the antenna port, then, connect your antenna cable to this port. 6. Make sure that you properly ground the Access Point. Ground the Access Point 7. 8. Line up the Access Points wall-mount slots with the two screws on the wall. Then, slide the Access Point down so that the screws fit snugly in the slots. Attach a screw (not included) in each of the two holes on the top of the mounting plate so that the Access Point is securely mounted to the wall. Attach the Access Point to the Wall 9. Connect the other end of the Ethernet network cable to a switch, router, or other device that supports Power over Ethernet. The Access Point will then be connected to your wired network. Now that the hardware installation is complete, proceed to Chapter 5: Quick Configuration Overview for directions on how to configure the Access Point. Wreless-G Exteror Access Pont wth Power Over Ethernet
Chapter
Quick Configuration Overview Chapter :
Quck Confguraton Overvew Overview The Access Point has been designed to be functional right out of the box with the default settings. However, if youd like to change these settings, the Access Point can be configured through your web browser with the web-based utility. This chapter explains how to use the utility. The utility can be accessed via web browsers, such as Microsoft Internet Explorer or Mozilla Firefox through the use of a computer that is networked with the Access Point. For a basic network setup, most users only have to use the following screens of the Utility:
Setup On the Setup screen, enter your basic network settings (IP address) here. Management Click the Administration tab and then select the Management screen. The Access Points default password is admn. To secure the Access Point, change the AP Password from its default. Most users will also customize their wireless settings:
Wreless On the Wireless screen, change default SSID under the Basic Wireless Settings tab. Select the level of security under the Wireless Security tab. Accessing the Web-Based Utility There are two ways to power your Access Point.
V Power Injector (e.g. Lnksys WAPPOE) Power up your Access Point first then connect the cable on your Injector to your PC. PoE swtch (e.g. Lnksys SRWP) Connect your Access Point and your PC to the same LAN. To access the web-based utility, perform the following steps:
1. Configure your PC with a static IP address in the same subnet as the Access Points default IP address
(192.168.1.245). If there is DHCP server connected to the switch, configure it to assign the IP address in 192.168.1.0/24 subnet. Your PC will get an IP address in the subnet through the DHCP. 2. 3. Launch your web browser, such as Internet Explorer or Mozilla Firefox and enter the Access Points default IP address, 9..., in the Address field. Press the Enter key. Enter admn in the User Name field. The first time you open the Web-based Utility, use the default password, admn. (You can set a new password from Administration > Management) Then click the OK button. After setting up the Access Point to use DHCP or manually configure a new IP address, move your Access Point to the desired network. You will have to use the new IP address the next time you access the Web-based Utility. Navigating the Web-Based Utility The web-based utility consists of the following five main tabs: Setup, Wreless, AP Mode, Admnstraton, and Status. Additional screens (sub tabs) will be available from most of the main tabs. The following briefly describes the main and sub tabs of the Utility. Setup Basc Setup Enter the Host Name and IP Address settings on this screen. Tme You can set the time either manually or automatically from a time server if the Access Point can access the public Internet. Wireless You will use the Wireless tabs to enter a variety of wireless settings for the Access Point. Basc Wreless Settngs Choose the wireless network mode (e.g. wireless-G), wireless channel, and SSID configuration on this screen. Wreless Securty Use this screen to configure the Access Points security settings including access authentication, data encryption, and wireless isolation. Wreless Connecton Control Use this screen to populate your Access List to permit or block certain MAC address access to your wireless network. Advanced Wreless Settngs Use this screen to configure the Access Points more advanced wireless settings such as Beacon interval, Output Power, etc. VLAN & QoS Use this screen to configure the VLAN and QoS related settings for the Access Point. Wreless-G Exteror Access Pont wth Power Over Ethernet
Chapter
Quick Configuration Overview AP Mode Use this screen to configure the Access Point operation mode with WDS (Wireless Distribution System). Administration You will use the Administration tabs to manage the Access Point. Management This screen allows you to customize the password and Simple Network Management Protocol
(SNMP) settings. Log Configure the Log settings for the Access Point on this screen. Factory Default Use this screen to reset the Access Point to its factory default settings. Frmware Upgrade Upgrade the Access Points firmware on this screen. Reboot Use this screen to reboot the Access Point. Confg Management You can back up the configuration file for the Access Point, as well as save the backup configuration file to the Access Point. Status You will be able to view status information for your local network, wireless networks, and network performance. Local Network This screen displays system information, including software & hardware version, MAC address, and IP address on the LAN side of the Access Point. Wreless This screen displays wireless network settings including SSID, network mode, and wireless channel. System Performance This screen displays the current traffic statistics of the Access Points Wireless and LAN ports. Wreless-G Exteror Access Pont wth Power Over Ethernet 9 Chapter
Advanced Configuration Chapter :
Advanced Confguraton Open your web browser and enter http://9...
into the Address field. Press the Enter key and the Password screen will appear. Address Bar NOTE: The default IP address is 9.... If the IP address has been changed using DHCP or via the console interface, enter the assigned IP address instead of the default. The first time you open the web-based utility, enter admn (the default username) in the User name field and enter it again in the Password field. Click the OK button. You can change the Access Points password later from the Administration > Management screen. Login Screen Web-Based Utility The first screen that appears in the web-based utility is the Setup screen. This allows you to change the Access Points general settings. There are five tabs across the top of the screen: Setup, Wreless, AP Mode, Admnstraton, and Status. Each tab contains screens that will help you configure and manage the Access Point. Setup > Basic Setup Setup > Basic Setup Enter names for the Access Point. The host name can be used to access the Web Utility through the network if DNS has been set up. The device name is for the benefit of identifying your Access Point after you log in. Setup Host Name This is the host name assigned to the Access Point. This host name will be published to your DNS server if the Access Point is configured to acquire the IP address through DHCP. In that case, Linksys recommends to follow the company policy on the host name assignment. The default name is Linksys. Devce Name You may assign any device name to the Access Point. This name is only used by the Access Point administrator for identification purposes. Unique, memorable names are helpful, especially if you are employing multiple access points on the same network. The default name is WAP00E. Network Setup The selections under this heading allow you to configure the Access Points IP address setting(s). IP Settings Statc IP Address Selected by default, this option is used to assign a static or fixed IP address to the Access Point. Local IP Address The IP address must be unique to your network. The default IP address is 9.... Subnet Mask The Subnet Mask must be the same as that set on the LAN that your Access Point is connected to. The default is ...0. Default Gateway Enter the Default Gateway Address, typically this is the IP address of your router. Wreless-G Exteror Access Pont wth Power Over Ethernet
0 Chapter
Advanced Configuration Prmary DNS (Requred) and Secondary DNS
(Optonal) Your ISP will provide you with at least one DNS (Domain Name System) Server IP Address. Automatc Confguraton - DHCP If you have a DHCP server enabled on the LAN and want it to assign an IP address to the Access Point, the select this option. Change these settings as described here and click Save Settngs to apply your changes, or click Cancel Changes to cancel your changes. Help information is available on the right side of the screen. Setup > Time This allows you to change the Access Points time settings. The correct time setting can help the administrator to search the system log to identify problems. to cancel your changes. Help information is available on the right side of the screen. Wireless > Basic Wireless Settings Change the basic wireless network settings on this screen. The Access Point can connect to up to four wireless networks (SSIDs) at the same time, so this screen offers settings for up to four different SSIDs. Each SSID owns its own MAC address on this Access Point. Setup > Time Time You can set the time either manually or automatically from a time server if the Access Point can access the public Internet. The default is to set the time Automatcally. Manually Select this option to set the date and time manually. Automatcally Select this option and time zone. The Access Point will contact the public time server to get the current time. Automatcally adjust clock for daylght savng changes Select this option if you are in using the Access Point in a location that observes daylight saving time. User Defned NTP Server Enable this option if you have set up local NTP server. Default is Disabled. NTP Server IP Enter the IP address of user defined NTP Server. Change these settings as described here and click Save Settngs to apply your changes, or click Cancel Changes Wireless > Basic Wireless Settings Basic Settings Configure the Wireless Network basic attributes for the entire system and for each SSID. Wreless Network Mode Select one of the following modes. The default is Mixed. Dsable To disable wireless connectivity completely. This might be useful during system maintenance. B-Only All the wireless client devices can be connected to the Access Point at Wireless-B data rates with maximum speed at 11Mbps. G-Only Wireless-G client devices can be connected at Wireless-G data rates with maximum speed at 54Mbps. Wireless-B clients cannot be connected in this mode. Mxed Both Wireless-B and Wireless-G client devices can be connected at their respective data rates. Wireless-G devices can be connected at Wireless-G data rates. Wreless Channel Select the appropriate channel to be used among your Access Point and your client devices. When Auto is selected, your Access Point will select the channel with the lowest amount of wireless interference while the system is powering up. Auto channel selection will start when you click Save Settngs button, it will take several seconds to scan through all the channels to find the best channel. The default setting is Auto. Wreless-G Exteror Access Pont wth Power Over Ethernet
Chapter
Advanced Configuration SSID Name The SSID is the unique name shared among all devices in a wireless network. It is case-sensitive, must not exceed 32 alphanumeric characters, and may be any keyboard character. Make sure this setting is the same for all devices in your wireless network. The default SSID name is lnksys-g. SSID Broadcast This option allows the SSID to be broadcast on your network. You may want to enable this function while configuring your network, but make sure that you disable it when you are finished. With this enabled, someone could easily obtain the SSID information with site survey software or Windows XP and gain unauthorized access to your network. Click Enabled to broadcast the SSID to all wireless devices in range. Click Disabled to increase network security and prevent the SSID from being seen on networked PCs. The default is Enabled in order to help users configure their network before use. Change these settings as described here and click Save Settngs to apply your changes, or click Cancel Changes to cancel your changes. Help information is available on the right side of the screen. Wireless > Wireless Security Change the Access Points wireless security settings on this screen. Wreless Isolaton (between SSID) Wireless Isolation prevents eavesdropping in the network. When it is Enabled, wireless frames received on this Access Point will not be forwarded to other wireless networks (SSIDs). For example, if you have a wireless hotspot, you may want to keep the wireless network (SSID) isolated from your other wireless networks (SSIDs). This is a global option applying to all SSIDs. The default is Enabled. The following options are specific for each SSID:
Securty Mode Select the wireless security mode you want to use: WPA-Personal, WPA2-Personal, WPA2-Personal Mixed, WPA-Enterprise, WPA2-Enterprise, WPA2-Enterprise Mixed, RADIUS, or WEP. (WPA stands for Wi-Fi Protected Access, which is a security standard stronger than WEP encryption and forward compatible with IEEE 802.11i. WEP stands for Wired Equivalent Privacy, Enterprise modes use a RADIUS server for authentication, while RADIUS stands for Remote Authentication Dial-In User Service.) Refer to the appropriate instructions below after you select the Authentication Type and SSID Interoperability settings. For detailed instructions on configuring wireless security for the Access Point, refer to Appendix B: Wireless Security Checklist. To disable wireless security completely, select Dsabled. The default is Dsabled. Wreless Isolaton (wthn SSID) When disabled, wireless PCs that are associated to the same network name (SSID), can see and transfer files between each other. By enabling this feature, Wireless PCs will not be able to see each other. This feature is very useful when setting up a wireless hotspot location. The default is Dsabled. Following section describes the detailed options for each Security Mode. WPA-Personal (aka WPA-PSK) Wireless > Wireless Security Wireless Security Select SSID Select any of the SSID names configured on the Basic Wireless Settings tab. Wireless > Wireless Security > WPA-Personal Encrypton WPA offers you two encryption methods, TKIP and AES for data encryption. Select the type of algorithm you want to use, TKIP or AES. The default is TKIP. Shared Secret Enter a shared secret of 8-63 characters. Wreless-G Exteror Access Pont wth Power Over Ethernet
Chapter
Advanced Configuration Key Renewal Tmeout Enter a Key Renewal Timeout period, which instructs the Access Point how often it should change the encryption keys. The default is 00 seconds. Key Renewal Tmeout Enter a Key Renewal Timeout period, which instructs the Access Point how often it should change the encryption keys. The default is 00 seconds. WPA2-Personal WPA-Enterprise This option features WPA used in coordination with a RADIUS server for client authentication. (This should only be used when a RADIUS server is connected to the Access Point.) Wireless > Wireless Security > WPA2-Personal Encrypton WPA2 always uses AES for data encryption. Shared Secret Enter a shared secret of 8-63 characters. Key Renewal Tmeout Enter a Key Renewal Timeout period, which instructs the Access Point how often it should change the encryption keys. The default is 00 seconds. WPA2-Personal Mixed This security mode supports from WPA-Personal to WPA2-Personal. You can have client devices that use either WPA-Personal or WPA2-Personal. The Access Point will automatically choose the encryption algorithm used by each client device. transition the Wireless > Wireless Security > WPA-Enterprise RADIUS Server IP Address Enter the RADIUS servers IP address. RADIUS Server Port Enter the port number used by the RADIUS server. The default is . Encrypton WPA offers you two encryption methods, TKIP and AES for data encryption. Select the type of algorithm you want to use, TKIP or AES. The default is TKIP. Shared Secret Enter the Shared Secret key used by the Access Point and RADIUS server. Key Renewal Tmeout Enter a Key Renewal Timeout period, which instructs the Access Point how often it should change the encryption keys. The default is 00 seconds. WPA2-Enterprise This option features WPA2 used in coordination with a RADIUS server for client authentication. (This should only be used when a RADIUS server is connected to the Access Point.) Wireless > Wireless Security > WPA2=Personal Mixed Encrypton Mixed Mode automatically chooses TKIP or AES for data encryption. Shared Secret Enter a shared secret of 8-63 characters. Wreless-G Exteror Access Pont wth Power Over Ethernet
Chapter
Advanced Configuration RADIUS Server Port Enter the port number used by the RADIUS server. The default is 1812. Encrypton Mixed Mode automatically chooses TKIP or AES for data encryption. Shared Secret Enter the Shared Secret key used by the Access Point and RADIUS server. Key Renewal Tmeout Enter a Key Renewal Timeout period, which instructs the Access Point how often it should change the encryption keys. The default is 3600 seconds. RADIUS This security mode is also known as Dynamic WEP with IEEE 802.1X. A RADIUS server is used for client authentication and WEP is used for data encryption. The WEP key is automatically generated by the RADIUS server. Manual WEP key is no longer supported to ensure compatibility with Microsofts Windows implementation. Wireless > Wireless Security > WPA2-Enterprise RADIUS Server IP Address Enter the RADIUS servers IP address. RADIUS Server Port Enter the port number used by the RADIUS server. The default is . Encrypton WPA2 always uses AES for data encryption. Shared Secret Enter the Shared Secret key used by the Access Point and RADIUS server. Key Renewal Tmeout Enter a Key Renewal Timeout period, which instructs the Access Point how often it should change the encryption keys. The default is 00 seconds. WPA2-Enterprise Mixed This security mode supports the transition from WPA-
Enterprise to WPA2-Enterprise. You can have client devices that use either WPA-Enterprise or WPA2-Enterprise. The Access Point will automatically choose the encryption algorithm used by each client device. Wireless > Wireless Security > RADIUS RADIUS Server IP Address Enter the RADIUS servers IP address. RADIUS Server Port Enter the port number used by the RADIUS server. The default is 1812. Shared Secret Enter the Shared Secret key used by the Access Point and RADIUS server. WEP Wireless > Wireless Security > WPA2-Enterprise Mixed RADIUS Server IP Address Enter the RADIUS servers IP address. This security mode is defined in the original IEEE 802.11. This mode is not recommended now due to its weak security protection. Users are urged to migrate to WPA or WPA2. Wreless-G Exteror Access Pont wth Power Over Ethernet
Chapter
Advanced Configuration Wireless > Wireless Connection Control This screen allows you to configure the Connection Control List to either permit or block specific wireless client devices connecting to (associating with) the Access Point. Wireless > Wireless Security > WEP Authentcaton Type Choose the 802.11 authentication type as either Open System or Shared Key. The default is Open System. Default Transmt Key Select the key to be used for data encryption. Encrypton Select a level of WEP encryption, 64 bits (10 hex digits) or 128 bits (26 hex digits). Passphrase If you want to generate WEP keys using a Passphrase, then enter the Passphrase in the field provided and click the Generate key. Those auto-generated keys are not as strong as manual WEP keys. Key - If you want to manually enter WEP keys, then complete the fields provided. Each WEP key can consist of the letters A through F and the numbers 0 through 9. It should be 10 characters in length for 64-bit encryption or 26 characters in length for 128-bit encryption. Change these settings as described here and click Save Settngs to apply your changes, or click Cancel Changes to cancel your changes. Help information is available on the right side of the screen. Disable There is no option to be configured for this mode. When you have finished making changes to the screen, click the Save Settngs button to save the changes, or click the Cancel Changes button to undo your changes. Help information is available on the right side of the screen. Wireless > Wireless Connection Control Wireless Connection Control Select SSID Select the SSID of the wireless network that you want to use wireless connection control on. Enabled/Dsabled Enable or disable wireless connection control. The default is disabled. Connection Control Allow only followng MAC addresses to connect to wreless network When this option is selected, only devices with a MAC address specified in the Connection Control List can connect to the Access Point. Prevent followng MAC addresses from connectng to wreless network When this option is selected, devices with a MAC address specified in the Connection Control List will not be allowed to connect to the Access Point. Wireless Client List Instead of manually entering the MAC addresses of each client, the Access Point provides a convenient way to select a specific client device from the client association table. Click this button and a window appears to let you select a MAC address from the table. The selected MAC address will be entered into the Connection Control List. Wreless-G Exteror Access Pont wth Power Over Ethernet
Chapter
Advanced Configuration Power Output You can adjust the output power of the Access Point to get the appropriate coverage for your wireless network. Select the level you need for your environment. If you are not sure of which setting to choose, then keep the default setting, 00%. Beacon Interval This value indicates the frequency interval of the beacon. A beacon is a packet broadcast by the Access Point to keep the network synchronized. A beacon includes the wireless networks service area, the Access Point address, the Broadcast destination addresses, a time stamp, Delivery Traffic Indicator Maps, and the Traffic Indicator Message (TIM). The default is 00 ms. DTIM Interval This value indicates how often the Access Point sends out a Delivery Traffic Indication Message
(DTIM). Lower settings result in more efficient networking, while preventing your PC from dropping into power-
saving sleep mode. Higher settings allow your PC to enter sleep mode, thus saving power, but interferes with wireless transmissions. The default is ms. RTS Threshold This setting determines how large a packet can be before the Access Point coordinates transmission and reception to ensure efficient communication. This value should remain at its default setting of . If you encounter inconsistent data flow, only minor modifications are recommended. Fragmentaton Threshold This specifies the maximum size a data packet can be before splitting and creating a new packet. It should remain at its default setting of . A smaller setting means smaller packets, which will create more packets for each transmission. If you experience high packet error rates, you can decrease this value, but it will likely decrease overall network performance. Only minor modifications of this value are recommended. Change these settings as described here and click Save Settngs to apply your changes, or click Cancel Changes to cancel your changes. Help information is available on the right side of the screen. Connection Control List MAC 0- Enter the MAC addresses of the wireless client devices you want to control. Change these settings as described here and click Save Settngs to apply your changes, or click Cancel Changes to cancel your changes. Help information is available on the right side of the screen. Wireless > Advanced Wireless Settings This screen allows you to configure the advanced settings for the Access Point. Linksys recommends to let your Access Point automatically adjust the parameters for maximum data throughput. Wireless > Advanced Wireless Settings Advanced Settings CTS Protecton Mode CTS (Clear-To-Send) Protection Mode function boosts the Access Points ability to catch all wireless transmissions, but will severely decrease performance. Keep the default setting, Auto, so the Access Point can use this feature as needed, when the Wireless-G products are not able to transmit to the Access Point in an environment with heavy 802.11b traffic. Select Dsabled if you want to permanently disable this feature. BSSBascRateSet This setting is a series of rates that are advertised to other wireless devices as defined in IEEE 802.11 specifications, so they know which data rates the Access Point can support. One of the rates is picked from the list for transmitting control frames, broadcast/
multicast frames, or ACK frames. To support both 802.11b
& 802.11g devices, use the Default (Mxed mode) setting so that frames can be decoded by all devices. To support 802.11g devices only, use the All (G-only mode) setting to achieve higher frame rates. For regular data frames, the transmission rate is configured through the Tx Rate Limiting on the Wireless > VLAN & QoS tab. Wreless-G Exteror Access Pont wth Power Over Ethernet
Chapter
Advanced Configuration QoS The following options are VLAN global settings for the Access Point. Default CoS (Prorty) Select Enabled if you want to assign a default CoS value to each SSID. This option is automatically enabled when the VLAN option is enabled. The default is Dsabled. U-APSD
(Unscheduled Automatc Power Save Delvery) This option is only available when WMM is enabled on any of the SSIDs. Select Enabled if you want client devices with U-APSD capability to take advantage of the power save mode. The default is Dsabled. SSID Name Displays the SSIDs defined under the Basic Wireless Settings tab. If an SSID has been disabled, the options cannot be configured. VLAN ID Select a VLAN ID (1 - 4094) for the SSID where you want to map the traffic to on the wired side. The wireless traffic will not carry VLAN information. Multiple SSIDs can map to the same VLAN on the wired side. Prorty You can assign the default priority (802.1p COS bits) for packets coming in from each wireless network by selecting a number from the drop-down menu. The higher the number, the higher the priority will be. The default is 0. Tx Rate Lmtaton You can limit the maximum data rate used in your network to save bandwidth and power consumption on client devices. The actual data rate is determined by the Auto-Fallback mechanism between your Access Point and a client device. The default is 54 Mbps for Mixed or G-Only wireless mode, 11 Mbps for B-
Only mode. WMM Wi-Fi Multimedia is a QoS feature defined by the WiFi Alliance before IEEE 802.11e was finalized. Now it is part of IEEE 802.11e. When this is enabled, it provides four priority queues for different types of traffic. It automatically maps the incoming packets to the appropriate queues based on QoS settings (in the IP or layer 2 header). WMM provides the capability to prioritize wireless traffic in your environment. The default is Dsabled (unchecked). Wireless > VLAN & QoS This screen allows you to configure the VLAN and QoS related settings for the Access Point. Wireless > VLAN & QoS VLAN The following options are global VLAN settings for the Access Point. VLAN Select Enabled if you want to pass 802.1q VLAN tagged traffic between the wired LAN and wireless LAN. Your Access Point will map the VLAN tag (wired side) to different SSIDs (wireless side) according to your specified settings. Select Disabled and your Access Point will drop all tagged traffic coming in from the wired LAN. The default is Dsabled. Default VLAN ID Enter the default VLAN ID number (1
- 4094), the default value is . The default VLAN number should match with your Switchs settings. For example, the SRW2024 has Trunk port mode which set default VLAN
(PVID) to 1 untagged, while General port mode can set PVID to any VLAN either tagged or untagged. VLAN Tag Set the tagging option for the default VLAN ID. This has to match your Switchs settings. The default is untagged. AP Management VLAN When the VLAN option is enabled, the value entered (VLAN ID) in this field defines the VLAN that connects to the Access Point. The default value is . The VLAN should be accessible from the wired side in order to use web-based utility. To access the web-based utility from wireless side, the SSID needs to map to the same VLAN ID. Remember to enable wireless web access on the Administration > Management tab. Wreless-G Exteror Access Pont wth Power Over Ethernet
Chapter
Advanced Configuration AP Mode On this screen you can change the Access Points mode of operation. In most cases, you can keep the default setting
- Access Point. You may wish to change the Access Points mode of operation if you want to use the Access Point as a wireless repeater to extend the range of your wireless network. You may also wish to change the Access Points mode of operation if you want to use the Access Point as a wireless bridge; for example, you can use two Access Points in Wireless Bridge mode to connect two wired networks that are in two different buildings. Wreless Repeater When set to Wireless Repeater mode, the Wireless Repeater is able to talk to up a remote access point within its range and retransmit its signal. Click Ste Survey to select the access point that will have its signal repeated by this Access Point or enter the MAC address of the access point manually. Desktop Laptop Access Point
- Wireless Repeater Mode Access Point Desktop Switch Laptop Wired LAN Modem Internet Wireless Repeater Mode AP Mode The Access Point offers three modes of operation: Access Point, Wireless Repeater, and Wireless Bridge. For the Repeater and Bridge modes, make sure the SSID, channel, and security settings are the same for the other wireless access points/devices. MAC Address The MAC address of the Access Point is displayed here. Access Pont The Mode is set to Access Point by default. This connects your wireless PCs to a wired network. In most cases, no change is necessary. Allow wreless sgnal to be repeated by a repeater Select this option if you want to use another wireless device to repeat the signal of this Access Point. You will need to enter the MAC address(es) of the repeating device(s). Up to 3 repeaters can be used. Wreless-G Exteror Access Pont wth Power Over Ethernet
Chapter
Advanced Configuration Wreless Brdge This mode connects physically separated wired networks using multiple access points. Wireless clients will not be able to connect to the access point in this mode. Enter the MAC address(es) of the access point(s) that will bridge to this access point. Wired LAN Wired LAN Administration > Management On this screen you can configure the password, Web Access, and SNMP settings. Switch Switch Access Point
- Wireless Bridge Mode Access Point
- Wireless Bridge Mode Access Point
- Wireless Bridge Mode Access Point
- Wireless Bridge Mode Access Point
- Wireless Bridge Mode Switch Switch Wired LAN Wired LAN Wireless Bridge Mode Administration > Management AP Password You should change the username/password that controls access to the Access Points web-based utility. Local AP Password User Name Modify the administrator username. The default is admin. AP Password Modify the administrator password for the Access Points web-based utility. The default is admin. Re-enter to confrm To confirm the new Password, enter it again in this field. Web Access To increase the security on accessing web-based utility. You can enable HTTPS. Once enabled, users need to use https:// when accessing the web-based utility. Web HTTPS Access Use secured HTTP session to access Web based Utility. The default is Dsabled. Wreless Web Access Allow or deny wireless clients to access Web based Utility. The default is Enabled. SNMP SNMP is a popular network monitoring and management protocol. It provides network administrators with the ability to monitor the status of the Access Point and Wreless-G Exteror Access Pont wth Power Over Ethernet
9 Chapter
Advanced Configuration receive notification of any critical events as they occur on the Access Point. To enable the SNMP support feature, select Enabled. Otherwise, select Dsabled. The default is Dsabled. Identification Contact Enter the name of the contact person, such as a network administrator, for the Access Point. Devce Name Enter the name you wish to give to the Access Point. Locaton Enter the location of the Access Point. Get Communty Enter the password that allows read-
only access to the Access Points SNMP information. Set Communty Enter the password that allows read/
write access to the Access Points SNMP information. SNMP Trap-Communty Enter the password required by the remote host computer that will receive trap messages or notices sent by the Access Point. SNMP Trusted Host You can restrict access to the Access Points SNMP information by IP address. Enter the IP address in the field provided. If this field is left blank, then access is permitted from any IP address. SNMP Trap-Destnaton Enter IP address of the remote host computer that will receive the trap messages. the Change these settings as described here and click Save Settngs to apply your changes, or click Cancel Changes to cancel your changes. Help information is displayed on the right-hand side of the screen, and click Help for additional details. Administration > Log On this screen you can configure the log settings and alerts of particular events. Log You can have logs that keep track of the Access Points activities. Email Alert E-Mal Alert If you want the Access Point to send e-mail alerts in the event of certain activities, select Enabled. The default is Dsabled. E-Mal Address for Logs Enter the e-mail address that will receive logs. Notification Queue Length Log Queue Length You can designate the length of the log that will be e-mailed to you. The default is 20 entries. Log Tme Threshold You can designate how often the log will be emailed to you. The default is 600 seconds (10 minutes). Syslog Notification Syslog is a standard protocol used to capture information about network activity. The Access Point supports this protocol and sends its activity logs to an external server. To enable Syslog, select Enabled. The default is Dsabled. Syslog Server IP Address Enter the IP address of the Syslog server. In addition to the standard event log, the Access Point can send a detailed log to an external Syslog server. The Access Points Syslog captures all log activities and includes this information about all data transmissions:
every connection source and destination IP address, IP server, and number of bytes transferred. Log Select the events that you want the Access Point to keep a log. Unauthorzed Logn Attempt If you want to receive alert logs about any unauthorized login attempts, click the checkbox. Authorzed Logn If you want to log authorized logins, click the checkbox. System Error Messages If you want to log system error messages, click the checkbox. Confguraton Changes If you want configuration changes, click the checkbox. to log any Change these settings as described here and click Save Settngs to apply your changes, or click Cancel Changes to cancel your changes. Help information is available on the right side of the screen. Administration > Log Wreless-G Exteror Access Pont wth Power Over Ethernet
0
1 | Manual Part 2 | Users Manual | 2.88 MiB | April 05 2007 |
Chapter
Advanced Configuration Administration > Factory Default On this screen you can restore the Access Points factory default settings. Administration > Firmware Upgrade Firmware Upgrade Before you upgrade the Access Points firmware, note all of your custom settings. After you upgrade its firmware, you may have to re-enter all of your configuration settings. To upgrade the Access Points firmware:
1. 2. 3. 4. Download the firmware upgrade file from the Linksys website, www.linksys.com. Extract the firmware upgrade file on your computer. On the Firmware Upgrade screen, enter the location of the firmware upgrade file in the field provided, or click the Browse button to find the file. Click the Upgrade button, and follow the on-screen instructions. Help information is available on the right side of the screen. Administration > Factory Default Factory Default Note any custom settings before you restore the factory defaults. Once the Access Point is reset, you will have to re-enter all of your configuration settings. Restore Factory Defaults To restore the Access Points factory default settings, click the Yes radio button. Then, click Save Settngs. Your Access Point will reboot and come back up with the factory default settings in a few seconds. Click Save Settngs to apply your change, or click Cancel Changes to cancel your change. Help information is available on the right side of the screen. Administration > Firmware Upgrade On this screen you can upgrade the Access Points firmware. Do not upgrade the firmware unless you are experiencing problems with the Access Point or the new firmware has a feature you want to use. Wreless-G Exteror Access Pont wth Power Over Ethernet
Chapter
Advanced Configuration Config Management Use this screen to upload or download configuration files for the Access Point. Save Confguraton To save a backup configuration file on a computer, click the Save Configuration to File button and follow the on-screen instructions. Restore Confguraton To upload a configuration file to the Access Point, enter the location of the configuration file in the field provided, or click the Browse button to find the file. Then click the Load button. Help information is available on the right side of the screen. Status > Local Network The Local Network screen displays the Access Points current status information for the local network. Administration > Reboot On this screen you can reboot the Access Point. Administration > Reboot Reboot This feature is useful when you need to remotely reboot the Access Point. Devce Reboot To reboot the Access Point, click the Yes option. Click Save Settngs to apply your change and the Access Point will reboot itself, or click Cancel Changes to cancel your change. Help information is available on the right side of the screen. Administration > Config Management On this screen you can create a backup configuration file or save a configuration file to the Access Point. Information Hardware Verson This is the version of the Access Points current hardware. Software Verson This is the version of the Access Points current software. Local MAC Address The MAC address of the Access Points Local Area Network (LAN) interface is displayed here. System Up Tme This is the length of time the Access Point has been running. Local Network IP Address This shows the Access Points IP Address, as it appears on your local network. Administration > Config Management Wreless-G Exteror Access Pont wth Power Over Ethernet
1 | Manual Part 3 | Users Manual | 1.71 MiB | April 05 2007 |
Chapter
Advanced Configuration Subnet Mask This shows the Access Points Subnet Mask. To update the status information, click the Refresh button. Help information is available on the right side of the screen. Status > Wireless The Wireless screen displays the Access Points current status information for the wireless network(s). Status > System Performance The System Performance screen displays the Access Points status information for its current settings and data transmissions. Status > Wireless Wireless Network Mode The Access Points wireless network mode is displayed here. SSID - MAC Address The MAC Addresses of the Access Points wireless interfaces are displayed here. SSID - The Access Points SSIDs that have been configured are displayed here. Channel The Access Points Channel setting for the SSID is shown here. VLAN Trunk The VLAN Trunk Status is displayed here. Prorty Settng The priority setting status is displayed here. To update the status information, click the Refresh button. Help information is available on the right side of the screen. Status > System Performance System Performance Wired Name This indicates that the statistics are for the wired network, the LAN. IP Address The Access Points local IP address is displayed here. MAC Address This shows the MAC Address of the Access Points wired interface. Connecton This shows the status of the Access Points connection for the wired network. Packets Receved This shows the number of packets received. Packets Sent This shows the number of packets sent. Bytes Receved This shows the number of bytes received. Bytes Sent This shows the number of bytes sent. Error Packets Receved This shows the number of error packets received. Drop Receved Packets This shows the number of packets being dropped after they were received. Wreless-G Exteror Access Pont wth Power Over Ethernet
Chapter
Advanced Configuration Wireless Name This indicates the wireless network/SSID to which the statistics refer. IP Address The Access Points local IP address is displayed here. MAC Address This shows the MAC Address of the Access Points wireless interface. Connecton This shows the status of the Access Points wireless networks. Packets Receved This shows the number of packets received for each wireless network. Packets Sent This shows the number of packets sent for each wireless network. Bytes Receved This shows the number of bytes received for each wireless network. Bytes Sent This shows the number of bytes sent for each wireless network. Error Packets Receved This shows the number of error packets received for each wireless network. Drop Receved Packets This shows the number of packets being dropped after they were received. Reset Counter Press this button to reset packet statistic counters to zeros. To update the status information, click the Refresh button. Help information is available on the right side of the screen. Wreless-G Exteror Access Pont wth Power Over Ethernet
Appendx A Introduction Appendx A:
Troubleshootng This appendix provides solutions to problems that may occur during the installation and operation of the Wireless-G Exterior Access Point with Power Over Ethernet. Read the description below to solve your problems. If you cant find an answer here, check the Linksys website at www.lnksys.com. Can the Access Point act as my DHCP Server?
No. The Access Point is nothing more than a wireless hub, and as such cannot be configured to handle DHCP capabilities. Can I run an application from a remote computer over the wireless network?
This will depend on whether or not the application is designed to be used over a network. Consult the applications documentation to determine if it supports operation over a network. Can I play multiplayer games with other users of the wireless network?
Yes, as long as the game supports multiple players over a LAN (local area network). Refer to the games documentation for more information. What is the IEEE 802.11b standard?
It is one of the IEEE standards for wireless networks. The 802.11b standard allows wireless networking hardware from different manufacturers to communicate, provided that the hardware complies with the 802.11b standard. The 802.11b standard states a maximum data transfer rate of 11Mbps and an operating frequency of 2.4GHz. What is the IEEE 802.11g standard?
It is one of the IEEE standards for wireless networks. The 802.11g standard allows wireless networking hardware from different manufacturers to communicate, provided that the hardware complies with the 802.11g standard. The 802.11g standard states a maximum data transfer rate of 54Mbps and an operating frequency of 2.4GHz. What IEEE 802.11b features are supported?
The product supports functions:
the following IEEE 802.11 CSMA/CA plus Acknowledge protocol Multi-Channel Roaming Automatic Rate Selection RTS/CTS feature Fragmentation Power Management What IEEE 802.11g features are supported?
The product supports the functions:
following IEEE 802.11g CSMA/CA plus Acknowledge protocol OFDM protocol Multi-Channel Roaming Automatic Rate Selection RTS/CTS feature Fragmentation Power Management What is Ad-hoc?
An Ad-hoc wireless LAN is a group of computers, each with a WLAN adapter, connected as an independent wireless LAN. An Ad-hoc wireless LAN is applicable at a departmental scale for a branch or SOHO operation. What is Infrastructure?
An integrated wireless and wired LAN is called an Infrastructure configuration. Infrastructure is applicable to enterprise scale for wireless access to a central database, or wireless application for mobile workers. What is roaming?
Roaming is the ability of a portable computer user to communicate continuously while moving freely throughout an area greater than that covered by a single Access Point. Before using the roaming function, the workstation must make sure that it is set to the same channel number as the Access Point of the dedicated coverage area. Wreless-G Exteror Access Pont wth Power Over Ethernet
Appendx A Introduction To achieve true seamless connectivity, the wireless LAN must incorporate a number of different functions. Each node and Access Point, for example, must always acknowledge receipt of each message. Each node must maintain contact with the wireless network even when not actually transmitting data. Achieving these functions simultaneously requires a dynamic RF networking technology that links Access Points and nodes. In such a system, the users end node undertakes a search for the best possible access to the system. First, it evaluates such factors as signal strength and quality, as well as the message load currently being carried by each Access Point and the distance of each Access Point to the wired backbone. Based on that information, the node next selects the right Access Point and registers its address. Communications between end node and host computer can then be transmitted up and down the backbone. As the user moves on, the end nodes RF transmitter regularly checks the system to determine whether it is in touch with the original Access Point or whether it should seek a new one. When a node no longer receives acknowledgment from its original Access Point, it undertakes a new search. Upon finding a new Access Point, it then re-registers, and the communication process continues. What is the ISM band?
The FCC and their counterparts outside of the U.S. have set aside bandwidth for unlicensed use in the ISM (Industrial, Scientific and Medical) band. Spectrum in the vicinity of 2.4 GHz, in particular, is being made available worldwide. This presents a truly revolutionary opportunity to place convenient high speed wireless capabilities in the hands of users around the globe. What is Spread Spectrum?
Spread Spectrum technology is a wideband radio frequency technique developed by the military for use in reliable, secure, mission-critical communications systems. It is designed to trade off bandwidth efficiency for reliability, integrity, and security. In other words, more bandwidth is consumed than in the case of narrowband transmission, but the trade-off produces a signal that is, in effect, louder and thus easier to detect, provided that the receiver knows the parameters of the spread-
spectrum signal being broadcast. If a receiver is not tuned to the right frequency, a spread-spectrum signal looks like background noise. There are two main alternatives, Direct Sequence Spread Spectrum (DSSS) and Frequency Hopping Spread Spectrum (FHSS). What is DSSS? What is FHSS? And what are their differences?
Frequency Hopping Spread Spectrum (FHSS) uses a narrowband carrier that changes frequency in a pattern that is known to both transmitter and receiver. Properly synchronized, the net effect is to maintain a single logical channel. To an unintended receiver, FHSS appears to be short-duration impulse noise. Direct Sequence Spread Spectrum (DSSS) generates a redundant bit pattern for each bit to be transmitted. This bit pattern is called a chip (or chipping code). The longer the chip, the greater the probability that the original data can be recovered. Even if one or more bits in the chip are damaged during transmission, statistical techniques embedded in the radio can recover the original data without the need for retransmission. To an unintended receiver, DSSS appears as low power wideband noise and is rejected (ignored) by most narrowband receivers. Would the information be intercepted while transmitting on air?
it has the WLAN features two-fold protection in security. On the hardware side, as with Direct Sequence Spread Spectrum technology, inherent security feature of scrambling. On the software side, the WLAN series offers a variety of wireless security methods to enhance security and access control. Users can set it up depending upon their needs. Can Linksys wireless products support file and printer sharing?
Linksys wireless products perform the same function as LAN products. Therefore, Linksys wireless products can work with NetWare, Windows NT/2000, or other LAN operating systems to support printer or file sharing. What is WEP?
WEP is Wired Equivalent Privacy, a data privacy mechanism based on a 40-bit shared-key algorithm, as described in the IEEE 802.11 standard. What is a MAC Address?
The Media Access Control (MAC) address is a unique number assigned by the manufacturer to any Ethernet networking device, such as a network adapter, that allows the network to identify it at the hardware level. For all practical purposes, this number is usually permanent. Unlike IP addresses, which can change every time a computer logs on to the network, the MAC address of a device stays the same, making it a valuable identifier for the network. Wreless-G Exteror Access Pont wth Power Over Ethernet
Appendx A Introduction How do I avoid interference?
Using multiple Access Points on the same channel and in close proximity to one another will generate interference. When employing multiple Access Points, make sure to operate each one on a different channel (frequency). How do I reset the Access Point?
Press the Reset button on the back of the Access Point for about ten seconds. This will reset the unit to its default settings. How do I resolve issues with signal loss?
There is no way to know the exact range of your wireless network without testing. Every obstacle placed between an Access Point and wireless PC will create signal loss. Leaded glass, metal, concrete floors, water, and walls will inhibit the signal and reduce range. Start with your Access Point and your wireless PC in the same room and move it away in small increments to determine the maximum range in your environment. You may also try using different channels, as this may eliminate interference affecting only one channel. Also, open the Access Points Web-based Utility. Click the Wireless tab and then the Advanced Wireless tab. Make sure the Output Power is set to 100%. Does the Access Point function as a firewall?
No. The Access Point is only a bridge from wired Ethernet to wireless clients. I have excellent signal strength, but I cannot see my network. Wireless security, such as WEP or WPA, is probably enabled on the Access Point, but not on your wireless adapter (or vice versa). Verify that the same wireless security settings are being used on all devices in your wireless network. What is the maximum number of users the Access Point can handle?
No more than 65, but this depends on the volume of data and may be fewer if many users create a large amount of network traffic. WEB: If your questions are not addressed here, refer to the Linksys website, www.lnksys.com Wreless-G Exteror Access Pont wth Power Over Ethernet
1 | Manual Part 4 | Users Manual | 1.29 MiB | April 05 2007 |
Appendx C Appendx C:
Glossary This glossary contains some basic networking terms you may come across when using this product. WEB: For additional terms, please visit the glossary at www.lnksys.com/glossary Access Mode Specifies the method by which user access is granted to the system. Access Pont A device that allows wireless-equipped computers and other devices to communicate with a wired network. Also used to expand the range of a wireless network. Access Profles Allows network managers to define profiles and rules for accessing the device. Access to management functions can be limited to user groups, which are defined by the following criteria:
Ingress interfaces Source IP address and/or Source IP subnets. ACE Filters in Access Control Lists (ACL) that determine which network traffic is forwarded. An ACE is based on the following criteria:
Protocol Protocol ID Source Port Destination Port Wildcard Mask Source IP Address Destination IP Address ACL (Access Control Lst) Access Control Lists are used to grant, deny, or limit access devices, features, or applications. Auto-negotaton Allows 10/100 Mbps or 10/100/1000 Mbps Ethernet ports to automatically establish the optimal duplex mode, flow control, and speed. Back Pressure A mechanism used with Half Duplex mode that enables a port not to receive a message. Bandwdth The transmission capacity of a given device or network. Bandwdth Assgnments Indicates the amount of bandwidth assigned to a specific application, user, and/or interface. Glossary Baud Indicates the number of signaling elements transmitted each second. Best Effort Indicates that traffic is assigned to the lowest priority queue, and packet delivery is not guaranteed. Bt A binary digit. Boot To start a device and cause it to start executing instructions. Browser An application program that provides a way to look at and interact with all the information on the World Wide Web. Brdge A device that connect two networks. Bridges are hardware specific, however they are protocol independent. Bridges operate at Layer 1 and Layer 2 levels. Broadcast Doman Devices sets that receive broadcast frames originating from any device within a designated set. Routers bind Broadcast domains, because routers do not forward broadcast frames. Broadcast Storm An excessive amount of broadcast messages simultaneously transmitted across a network by a single port. Forwarded message responses are heaped onto the network, overloading network resources or causing the network to time out. Burst A packet transmission at faster than normal rates. Bursts are limited in time and only occur under specific conditions. Burst Sze Indicates the burst size transmitted at a faster than normal rate. Byte A unit of data that is usually eight bits long Cable Modem A device that connects a computer to the cable television network, which in turn connects to the Internet. CBS (Commtted Burst Sze) Indicates the maximum number of data bits transmitted within a specific time interval. CIR (Commtted Informaton Rate) The data rate is averaged over a minimum time increment. Class Maps An aspect of Quality of Service system that is comprised of an IP ACL and/or a MAC ACL. Class maps are configured to match packet criteria, and are matched to packets in a first-fit fashion. Combo Ports A single logical port with two physical connections, including an RJ-45 connection and a SFP connection. Communtes Specifies a group of users which retain the same system access rights. Wreless-G Exteror Access Pont wth Power Over Ethernet
9 Appendx C Glossary CoS (Class of Servce) The 802.1p priority scheme. CoS provides a method for tagging packets with priority information. A CoS value between 0-7 is added to the Layer II header of packets, where zero is the lowest priority and seven is the highest. DDNS (Dynamc Doman Name System) Allows the hosting of a website, FTP server, or e-mail server with a fixed domain name (e.g., www.xyz.com) and a dynamic IP address. Default Gateway A device that forwards Internet traffic from your local area network. DHCP
(Dynamc Host Confguraton Protocol) A networking protocol that allows administrators to assign temporary IP addresses to network computers by leasing an IP address to a user for a limited amount of time, instead of assigning permanent IP addresses. DHCP Clents An Internet host using DHCP to obtain configuration parameters, such as a network address. DHCP Server An Internet host that returns configuration parameters to DHCP clients. DNS (Doman Name Server) The IP address of your ISPs server, which translates the names of websites into IP addresses. Doman A specific name for a network of computers. Download To receive a file transmitted over a network. DSL (Dgtal Subscrber Lne) An always-on broadband connection over traditional phone lines. DSCP (DffServ Code Pont) Provides a method of tagging IP packets with QoS priority information. Dynamc IP Address A temporary IP address assigned by a DHCP server.
(Enhanced Provides Routng EIGRP Protocol) for variable-length subnet mask, and supports multiple network layer protocols. Interor Gateway fast convergence, support Encrypton Encoding data transmitted in a network. Ethernet IEEE standard network protocol that specifies how data is placed on and retrieved from a common transmission medium. Frmware The programming code that runs a networking device. Flow Control Enables speed devices to communicate with higher speed devices. This is implemented by the higher speed device refraining from sending packets. lower FTP (Fle Transfer Protocol) A protocol used to transfer files over a TCP/IP network. Full Duplex The ability of a networking device to receive and transmit data simultaneously. GARP (General Attrbutes Regstraton Protocol) Registers client stations into a multicast domain. Gateway A device that interconnects networks with different, incompatible communications protocols. GBIC (GgaBt Interface Converter) A hardware module used to attach network devices to fiber-based transmission systems. GBIC converts the serial electrical signals to serial optical signals and vice versa. GVRP (GARP VLAN Regstraton Protocol) Registers client stations into a VLANs. Half Duplex Data transmission that can occur in two directions over a single line, but only one direction at a time.
(HyperText HTTP Protocol) The communications protocol used to connect to servers on the World Wide Web. Transport HTTPS (HyperText Transport Protocol Secure) An extension to the standard HTTP protocol that provides confidentiality by encrypting the traffic from the website. By default this protocol uses TCP port 443. ICMP (Internet Control Message Protocol) Allows the gateway or destination host to communicate with the source host. For example, to report a processing error. IGMP (Internet Group Management Protocol) Allows hosts to notify their local switch or router that they want to receive transmissions assigned to a specific multicast group. IP (Internet Protocol) A protocol used to send data over a network. IP Address The address used to identify a computer or device on a network. IPCONFIG A Windows 2000 and XP utility that displays the IP address for a particular networking device. IPSec (Internet Protocol Securty) A VPN protocol used to implement secure exchange of packets at the IP layer. ISP (Internet Servce Provder) A company that provides access to the Internet. Jumbo Frames Enable transporting identical data in fewer frames. Jumbo Frames reduce overhead, lower processing time, and ensure fewer interrupts. LAG (Lnk Aggregated Group) Aggregates ports or VLANs into a single virtual port or VLAN. LAN The computers and networking products that make up your local network. Wreless-G Exteror Access Pont wth Power Over Ethernet
0 Appendx C Glossary MAC (Meda Access Control) Address The unique address that a manufacturer assigns to each networking device. RADIUS
(Remote Authentcaton Dal-In User Servce) A protocol that uses an authentication server to control network access. Mask A filter that includes or excludes certain values, for example parts of an IP address. RJ- (Regstered Jack-) An Ethernet connector that holds up to eight wires. Mbps (MegaBts Per Second) One million bits per second; a unit of measurement for data transmission. MD (Message Dgest ) An algorithm that produces a 128-bit hash. MD5 is a variation of MD4, and increases MD4 security. MD5 verifies the integrity of the communication and authenticates the origin of the communication. MDI (Meda Dependent Interface) A cable used for end stations. MDIX (Meda Dependent Interface wth Crossover) A cable used for hubs and switches. MIB (Management Informaton Base) MIBs contain information describing specific aspects of network components. Multcast Transmits copies of a single packet to multiple ports. Network A series of computers or devices connected for the purpose of data sharing, storage, and/or transmission between users. NMS (Network Management System) An interface that provides a method of managing a system. OID (Object Identfer) Used by SNMP to identify managed objects. In the SNMP Manager/Agent network management paradigm, each managed object must have an OID to identify it. Packet A unit of data sent over a network. Png (Packet INternet Groper) An Internet utility used to determine whether a particular IP address is online. Polcng Determines if traffic levels are within a specified profile. Policing manages the maximum traffic rate used to send or receive packets on an interface. Port The connection point on a computer or networking device used for plugging in cables or adapters. Port Mrrorng Monitors and mirrors network traffic by forwarding copies of incoming and outgoing packets from one port to a monitoring port. Power over Ethernet (PoE) A technology enabling an Ethernet network cable to deliver both data and power. QoS (Qualty of Servce) Provides policies that contain sets of filters (rules). QoS allows network managers to decide how and what network traffic is forwarded according to priorities, application types, and source and destination addresses. RMON information to be collected from a single workstation.
(Remote Montorng) Provides network Router A networking device that connects multiple networks together. RSTP (Rapd Spannng Tree Protocol) Detects and uses network topologies that allow a faster convergence of the spanning tree, without creating forwarding loops. Server Any computer whose function in a network is to provide user access to files, printing, communications, and other services. SMTP (Smple Mal Transfer Protocol) The standard e-mail protocol on the Internet. SNMP (Smple Network Management Protocol) A widely used network monitoring and control protocol. SSH Secure Shell. A utility that uses strong authentication and secure communications to log in to another computer over a network. SSL (Secure Socket Layer) Encryption technology for the Internet used to provide secure transactions, such as the transmission of credit card numbers for e-commerce. Statc IP Address A fixed address assigned to a computer or device that is connected to a network. STP (Spannng Tree Protocol) Prevents loops in network traffic. The Spanning Tree Protocol (STP) provides tree topography for any arrangement of bridges. STP provides one path between end stations on a network, eliminating loops. Subnet (Sub-network) Subnets are portions of a network that share a common address component. In TCP/IP networks, devices that share a prefix are part of the same subnet. For example, all devices with a prefix of 157.100.100.100 are part of the same subnet. Subnet Mask An address code that determines the size of the network. Swtch Filters and segments. Switches support any packet protocol type. forwards packets between LAN TACACS+ (Termnal Access Controller Access Control System Plus) Proprietary Cisco enhancement to Terminal Access Controller Access Control System (TACACS). Provides additional support for authentication, authorization, and accounting. Wreless-G Exteror Access Pont wth Power Over Ethernet
Appendx C Glossary TCP (Transmsson Control Protocol) A network protocol for transmitting data that requires acknowledgement from the recipient of data sent. TCP/IP
(Transmsson Control Protocol/Internet Protocol) A set of instructions PCs use to communicate over a network. Telnet A user command and TCP/IP protocol used for accessing remote PCs. TFTP (Trval Fle Transfer Protocol) A version of the TCP/IP FTP protocol that has no directory or password capability. Throughput The amount of data moved successfully from one node to another in a given time period. Trunkng Link Aggregation. Optimizes port usage by linking a group of ports together to form a single trunk
(aggregated groups). TX Rate Transmission Rate. UDP (User Data Protocol) Communication protocol that transmits packets but does not guarantee their delivery. Upgrade To replace existing software or firmware with a newer version. Upload To transmit a file over a network. URL (Unform Resource Locator) The address of a file located on the Internet. VLAN (Vrtual Local Area Networks) Logical subgroups that constitute a Local Area Network (LAN). This is done in software rather than defining a hardware solution. WAN (Wde Area Network) Networks that cover a large geographical area. Wldcard Mask Specifies which IP address bits are used, and which bits are ignored. A wild card mask of 255.255.255.255 indicates that no bit is important. A wildcard of 0.0.0.0 indicates that all the bits are important. For example, if the destination IP address is 149.36.184.198 and the wildcard mask is 255.36.184.00, the first two bits of the IP address are used, while the last two bits are ignored. Wreless-G Exteror Access Pont wth Power Over Ethernet
Appendx D Appendx D:
Specfcatons Specifications WAP200E IEEE802.11g, IEEE802.11b, IEEE802.3, IEEE802.3u, IEEE802.3af (Power Over Ethernet), 802.1p (QoS priority), 802.1Q (VLAN), 802.1X
(Security Authentication), 802.11i - Ready (Security WPA2), 802.11e - Ready (WMM
& U-APSD), 802.11F (Wireless Roaming) 1 Ethernet, 1 External Antenna Reset UTP CAT 5 Power, Ethernet, Wireless Linux 1, 2 and 2c Access Point Mode, point-to-point Bridge Mode, point-to-multipoint Bridge Mode, Repeater Mode 802.11b/DSSS, 11g/ODFM 11b: 1, 2, 5.5, 11 Mbps, 11g: 6, 9, 11, 12, 18, 24, 36, 48, 54 Mbps 11 North America, 13 Europe (ETSI and Japan) Auto-channel selection 2x 6dBi (directional) Specficatons Model Standards Ports Buttons Cabling Type LEDs Operating System Management SNMP Version Operatng Modes Access Point Wreless Spec/Modulation Data Rates Channels
# of Internal Ant. Ant. connector type N-type Detachable y/n/na RF Pwr (EIRP) in dBm Antenna Gain in dBi Adjustable power Receiver Sensitivity y (sold separately) 11.g: Typical - 16.5dBm, 11.b: Typical - 17dBm Internal antenna: 6dBi y 11.g: 54Mbps@ -65dBm, 11.b: 11Mbps@ -85dBM WEP, WPA-PSK, WPA2-PSK, WPA-ENT, WPA2-ENT Wireless Connection Control:
MAC-Based SSID Broadcast Enable/Disable IEEE 802.1X support Securty WEP/WPA/WPA2 Connection Control SSID Broadcast 802.1X Wireless Client Isolation Wireless Client devices can be isolated from each other either within an SSID or between two SSIDs. Both isolation modes can be enabled in the same time. Web-based Utility Access Control Wreless Securty WEP bits WPA bits & params WPA2 bits & params SSID Broadcast on/off Client Isolation MAC-based Wireless Connection Control Wireless Web GUI Access on/off Qualty of Servce QoS General HTTP/HTTPS, wireless client web GUI access control 64, 128 128 - TKIP/AES 256 - AES Yes Yes Yes 4 queues WMM wireless traffic prioritization Wireless roaming based on IAPP (802.11F) Load Balancing Auto-channel selection Yes Wreless-G Exteror Access Pont wth Power Over Ethernet
Appendx D Specifications Envronmental Dimensions Weight Mounting options Power Max Power Draw PoE In PoE Out Certification Operating Temp. Storage Temp. Operating Humidity Storage Humidity 6.42" x 8.07" x 2.17"
163 x 205 x 55mm 2.47 lb (1.121 kg) Industrial-strength, weather-proof housing, NEMA IP53 rating, lighting protection for outdoor enclosure, ceiling or wall mountable 48V DC, 350mA 4.8 Watt Yes No FCC, IC, CE
-4 to 140F (-20 to 60c)
-4 to 140F (-20 to 60c) 5 to 95%, noncondensing 5 to 95%, noncondensing Wreless-G Exteror Access Pont wth Power Over Ethernet
Appendx E Warranty and Regulatory Information Appendx E:
Warranty and Regulatory Informaton Limited Warranty Linksys warrants to You that, for a period of three years
(the "Warranty Period"), your Linksys Product will be substantially free of defects in materials and workmanship under normal use. Your exclusive remedy and Linksys entire liability under this warranty will be for Linksys at its option to repair or replace the Product or refund Your purchase price less any rebates. This limited warranty extends only to the original purchaser. If the Product proves defective during the Warranty Period call Linksys Technical Support in order to obtain a Return Authorization Number, if applicable. BE SURE TO HAVE YOUR PROOF OF PURCHASE ON HAND WHEN CALLING. If You are requested to return the Product, mark the Return Authorization Number clearly on the outside of the package and include a copy of your original proof of purchase. RETURN REQUESTS CANNOT BE PROCESSED WITHOUT PROOF OF PURCHASE. You are responsible for shipping defective Products to Linksys. Linksys pays for UPS Ground shipping from Linksys back to You only. Customers located outside of the United States of America and Canada are responsible for all shipping and handling charges. CONDITIONS, IMPLIED WARRANTIES AND CONDITIONS OF ALL MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED TO THE DURATION OF THE WARRANTY PERIOD. ALL OTHER EXPRESS OR IMPLIED AND WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF NON-INFRINGEMENT, ARE DISCLAIMED. Some jurisdictions do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to You. This warranty gives You specific legal rights, and You may also have other rights which vary by jurisdiction. REPRESENTATIONS This warranty does not apply if the Product (a) has been altered, except by Linksys, (b) has not been installed, operated, repaired, or maintained in accordance with instructions supplied by Linksys, or (c) has been subjected to abnormal physical or electrical stress, misuse, negligence, or accident. In addition, due to the continual development of new techniques for intruding upon and attacking networks, Linksys does not warrant that the Product will be free of vulnerability to intrusion or attack. TO THE EXTENT NOT PROHIBITED BY LAW, IN NO EVENT WILL LINKSYS BE LIABLE FOR ANY LOST DATA, REVENUE OR PROFIT, OR FOR SPECIAL, INDIRECT, CONSEQUENTIAL, INCIDENTAL OR PUNITIVE DAMAGES, REGARDLESS OF THE THEORY OF LIABILITY (INCLUDING NEGLIGENCE), ARISING OUT OF OR RELATED TO THE USE OF OR INABILITY TO USE THE PRODUCT (INCLUDING ANY SOFTWARE), EVEN IF LINKSYS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. IN NO EVENT WILL LINKSYS LIABILITY EXCEED THE AMOUNT PAID BY YOU FOR THE PRODUCT. The foregoing limitations will apply even if any warranty or remedy provided under this Agreement fails of its essential purpose. Some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to You. Please direct all inquiries to: Linksys, P.O. Box 18558, Irvine, CA 92623. FCC Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This product has been tested and complies with the specifications for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used according to the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which is found by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna Increase the separation between the equipment or devices Connect the equipment to an outlet other than the receivers Consult a dealer or an experienced radio/TV technician for assistance FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate this equipment. Wreless-G Exteror Access Pont wth Power Over Ethernet
Appendx E Warranty and Regulatory Information FCC Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. The availability of some specific channels and/or operational frequency bands are country dependent and are firmware programmed at the factory to match the intended destination. The firmware setting is not accessible by the end user. Safety Notices Caution: To reduce the risk of fire, use only No.26 AWG or larger telecommunication line cord. Do not use this product near water, for example, in a wet basement or near a swimming pool. Avoid using this product during an electrical storm. There may be a remote risk of electric shock from lightning. WARNING: This product contains lead, known to the State of California to cause cancer, and birth defects or other reproductive harm. Wash hands after handling. Industry Canada Statement This device complies with Industry Canada ICES-003 and RSS210 rules. Operation is subject to the following two conditions:
1. 2. This device may not cause interference and This device must accept any interference, including interference that may cause undesired operation of the device. This device has been designed to operate with an antenna having a maximum gain of 9 dBi. Antenna having a higher gain is strictly prohibited per regulations of Industry Canada. The required antenna impedance is 50 ohms. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the EIRP is not more than required for successful communication. Industry Canada Radiation Exposure Statement:
This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Avis dIndustrie Canada Cet appareil est conforme aux normes NMB003 et RSS210 dIndustrie Canada. Lutilisation de ce dispositif est autorise seulement aux conditions suivantes :
1. 2. il ne doit pas produire de brouillage et il doit accepter tout brouillage radiolectrique reu, mme si ce brouillage est susceptible de compromettre le fonctionnement du dispositif. Le dispositif a t conu pour fonctionner avec une antenne ayant un gain maximum de 9 dBi. Les rglements dIndustrie Canada interdisent strictement lutilisation dantennes dont le gain est suprieur cette limite. Limpdance requise de lantenne est de 50 ohms. Afin de rduire le risque dinterfrence aux autres utilisateurs, le type dantenne et son gain doivent tre choisis de faon ce que la puissance isotrope rayonne quivalente (p.i.r.e.) ne soit pas suprieure au niveau requis pour obtenir une communication satisfaisante. Avis dIndustrie Canada concernant lexposition aux radiofrquences :
Ce matriel est conforme aux limites tablies par IC en matire dexposition aux radiofrquences dans un environnement non contrl. Ce matriel doit tre install et utilis une distance dau moins 20 cm entre lantenne et le corps de lutilisateur. Lmetteur ne doit pas tre plac prs dune autre antenne ou dun autre metteur, ou fonctionner avec une autre antenne ou un autre metteur. Wreless-G Exteror Access Pont wth Power Over Ethernet
Appendx E Warranty and Regulatory Information User Information for Consumer Products Covered by EU Directive 2002/96/EC on Waste Electric and Electronic Equipment
(WEEE) This document contains important information for users with regards to the proper disposal and recycling of Linksys products. Consumers are required to comply with this notice for all electronic products bearing the following symbol:
Englsh - Envronmental Informaton for Customers n the European Unon European Directive 2002/96/EC requires that the equipment bearing this symbol on the product and/or its packaging must not be disposed of with unsorted municipal waste. The symbol indicates that this product should be disposed of separately from regular household waste streams. It is your responsibility to dispose of this and other electric and electronic equipment via designated collection facilities appointed by the government or local authorities. Correct disposal and recycling will help prevent potential negative consequences to the environment and human health. For more detailed information about the disposal of your old equipment, please contact your local authorities, waste disposal service, or the shop where you purchased the product.
(Bulgaran)
2002/96/EC ,
, . Cetna (Czech) - Informace o ochran votnho prosted pro zkaznky v zemch Evropsk une Evropsk smrnice 2002/96/ES zakazuje, aby zazen oznaen tmto symbolem na produktu anebo na obalu bylo likvidovno s netdnm komunlnm odpadem. Tento symbol udv, e dan produkt mus bt likvidovn oddlen od bnho komunlnho odpadu. Odpovdte za likvidaci tohoto produktu a dalch elektrickch a elektronickch zazen prostednictvm urench sbrnch mst stanovench vldou nebo mstnmi ady. Sprvn likvidace a recyklace pomh pedchzet potencilnm negativnm dopadm na ivotn prosted a lidsk zdrav. Podrobnj informace o likvidaci starho vybaven si laskav vydejte od mstnch ad, podniku zabvajcho se likvidac komunlnch odpad nebo obchodu, kde jste produkt zakoupili. Dansk (Dansh) - Mljnformaton for kunder EU EU-direktiv 2002/96/EF krver, at udstyr der brer dette symbol p produktet og/eller emballagen ikke m bortskaffes som usorteret kommunalt affald. Symbolet betyder, at dette produkt skal bortskaffes adskilt fra det almindelige husholdningsaffald. Det er dit ansvar at bortskaffe dette og andet elektrisk og elektronisk udstyr via bestemte indsamlingssteder udpeget af staten eller de lokale myndigheder. Korrekt bortskaffelse og genvinding vil hjlpe med til at undg mulige skader for miljet og menneskers sundhed. Kontakt venligst de lokale myndigheder, renovationstjenesten eller den butik, hvor du har kbt produktet, angende mere detaljeret information om bortskaffelse af dit gamle udstyr. Deutsch (German) - Umweltnformaton fr Kunden
nnerhalb der Europschen Unon Die Europische Richtlinie 2002/96/EC verlangt, dass technische Ausrstung, die direkt am Gert und/oder an der Verpackung mit diesem Symbol versehen ist
, nicht zusammen mit unsortiertem Gemeindeabfall entsorgt werden darf. Das Symbol weist darauf hin, dass das Produkt von regulrem Haushaltmll getrennt entsorgt werden sollte. Es liegt in Ihrer Verantwortung, dieses Gert und andere elektrische und elektronische Gerte ber die dafr zustndigen und von der Regierung oder rtlichen Behrden dazu bestimmten Sammelstellen zu entsorgen. Ordnungsgemes Entsorgen und Recyceln trgt dazu bei, potentielle negative Folgen fr Umwelt und die menschliche Gesundheit zu vermeiden. Wenn Sie weitere Informationen zur Entsorgung Ihrer Altgerte bentigen, wenden Sie sich bitte an die rtlichen Behrden oder stdtischen Entsorgungsdienste oder an den Hndler, bei dem Sie das Produkt erworben haben. Wreless-G Exteror Access Pont wth Power Over Ethernet
Appendx E Warranty and Regulatory Information
nformatsoon Eest (Estonan) - Keskkonnaalane Euroopa Ldus asuvatele klentdele Euroopa Liidu direktiivi 2002/96/E nuete kohaselt on seadmeid, millel on tootel vi pakendil kesolev smbol
, keelatud krvaldada koos sorteerimata olmejtmetega. See smbol nitab, et toode tuleks krvaldada eraldi tavalistest olmejtmevoogudest. Olete kohustatud krvaldama kesoleva ja ka muud elektri- ja elektroonikaseadmed riigi vi kohalike ametiasutuste poolt ette nhtud kogumispunktide kaudu. Seadmete korrektne krvaldamine ja ringlussevtt aitab vltida vimalikke negatiivseid tagajrgi keskkonnale ning inimeste tervisele. Vanade seadmete krvaldamise kohta tpsema informatsiooni saamiseks vtke palun hendust kohalike ametiasutustega, jtmekitlusfirmaga vi kauplusega, kust te toote ostsite. Espaol (Spansh) - Informacn medoambental para clentes de la Unn Europea La Directiva 2002/96/CE de la UE exige que los equipos que lleven este smbolo en el propio aparato y/o en su embalaje no deben eliminarse junto con otros residuos urbanos no seleccionados. El smbolo indica que el producto en cuestin debe separarse de los residuos domsticos convencionales con vistas a su eliminacin. Es responsabilidad suya desechar este y cualesquiera otros aparatos elctricos y electrnicos a travs de los puntos de recogida que ponen a su disposicin el gobierno y las autoridades locales. Al desechar y reciclar correctamente estos aparatos estar contribuyendo a evitar posibles consecuencias negativas para el medio ambiente y la salud de las personas. Si desea obtener informacin ms detallada sobre la eliminacin segura de su aparato usado, consulte a las autoridades locales, al servicio de recogida y eliminacin de residuos de su zona o pregunte en la tienda donde adquiri el producto.
(Greek)
2002/96/EC
. Franas (French) - Informatons envronnementales pour les clents de lUnon europenne La directive europenne 2002/96/CE exige que lquipement sur lequel est appos ce symbole sur le produit et/ou son emballage ne soit pas jet avec les autres ordures mnagres. Ce symbole indique que le produit doit tre limin dans un circuit distinct de celui pour les dchets des mnages. Il est de votre responsabilit de jeter ce matriel ainsi que tout autre matriel lectrique ou lectronique par les moyens de collecte indiqus par le gouvernement et les pouvoirs publics des collectivits territoriales. Llimination et le recyclage en bonne et due forme ont pour but de lutter contre limpact nfaste potentiel de ce type de produits sur lenvironnement et la sant publique. Pour plus dinformations sur le mode dlimination de votre ancien quipement, veuillez prendre contact avec les pouvoirs publics locaux, le service de traitement des dchets, ou lendroit o vous avez achet le produit. Italano (Italan) - Informazon relatve allambente per clent resdent nellUnone Europea La direttiva europea 2002/96/EC richiede che le apparecchiature contrassegnate con questo simbolo sul prodotto e/o sullimballaggio non siano smaltite insieme ai rifiuti urbani non differenziati. Il simbolo indica che questo prodotto non deve essere smaltito insieme ai normali rifiuti domestici. responsabilit del proprietario smaltire sia questi prodotti sia le altre apparecchiature elettriche ed elettroniche mediante le specifiche strutture di raccolta indicate dal governo o dagli enti pubblici locali. Il corretto smaltimento ed il riciclaggio aiuteranno a prevenire conseguenze potenzialmente negative per lambiente e per la salute dellessere umano. Per ricevere informazioni pi dettagliate circa lo smaltimento delle vecchie apparecchiature in Vostro possesso, Vi invitiamo a contattare gli enti pubblici di competenza, il servizio di smaltimento rifiuti o il negozio nel quale avete acquistato il prodotto. Latveu valoda (Latvan) - Ekoloska nformcja klentem Eropas Savenbas jursdkcj Direktv 2002/96/EK ir prasba, ka aprkojumu, kam pievienota zme uz paa izstrdjuma vai uz t iesaiojuma, nedrkst izmest neirot veid kop ar komunlajiem atkritumiem
(tiem, ko rada vietji iedzvotji un uzmumi). zme nozm to, ka ierce ir jizmet atkritumos t, lai t nenonktu kop ar parastiem mjsaimniecbas atkritumiem. Jsu pienkums ir o un citas elektriskas un elektroniskas ierces izmest atkritumos, izmantojot paus atkritumu savkanas veidus un ldzekus, ko nodroina valsts un pavaldbu iestdes. Ja izmeana atkritumos un prstrde tiek veikta pareizi, tad mazins iespjamais kaitjums dabai un cilvku veselbai. Skkas zias par novecojua aprkojuma izmeanu atkritumos js varat saemt vietj pavaldb, atkritumu savkanas dienest, k ar veikal, kur iegdjties o izstrdjumu. Wreless-G Exteror Access Pont wth Power Over Ethernet
Appendx E Warranty and Regulatory Information Letuvka (Lthuanan) - Aplnkosaugos nformacja, skrta Europos Sjungos vartotojams Europos direktyva 2002/96/EC numato, kad rangos, kuri ir kurios pakuot yra paymta iuo simboliu (veskite simbol), negalima alinti kartu su neriuotomis komunalinmis atliekomis. is simbolis rodo, kad gamin reikia alinti atskirai nuo bendro buitini atliek srauto. Js privalote utikrinti, kad i ir kita elektros ar elektronin ranga bt alinama per tam tikras nacionalins ar vietins valdios nustatytas atliek rinkimo sistemas. Tinkamai alinant ir perdirbant atliekas, bus ivengta galimos alos aplinkai ir moni sveikatai. Daugiau informacijos apie js senos rangos alinim gali pateikti vietins valdios institucijos, atliek alinimo tarnybos arba parduotuvs, kuriose sigijote t gamin. Malt (Maltese) - Informazzjon Ambjental gal Kljent
fl-Unjon Ewropea Id-Direttiva Ewropea 2002/96/KE titlob li t-tagmir li jkun fih is-
simbolu fuq il-prodott u/jew fuq l-ippakkjar ma jistax jintrema ma skart muniipali li ma iex isseparat. Is-simbolu jindika li dan il-prodott gandu jintrema separatament minn ma l-
iskart domestiku regolari. Hija responsabbilt tiegek li tarmi dan it-tagmir u kull tagmir ieor ta l-elettriku u elettroniku permezz ta failitajiet ta bir appuntati apposta mill-gvern jew mill-awtoritajiet lokali. Ir-rimi bmod korrett u r-riikla jgin jipprevjeni konsegwenzi negattivi potenzjali gall-ambjent u gas-saa tal-bniedem. Gal aktar informazzjoni dettaljata dwar ir-rimi tat-tagmir antik tiegek, jekk jogbok ikkuntattja lill-awtoritajiet lokali tiegek, is-servizzi gar-rimi ta l-iskart, jew il-anut minn fejn xtrajt il-prodott. Magyar (Hungaran) - Krnyezetvdelm nformc az eurpa uns vsrlk szmra A 2002/96/EC szm eurpai unis irnyelv megkvnja, hogy azokat a termkeket, amelyeken, s/vagy amelyek csomagolsn az albbi cmke megjelenik, tilos a tbbi szelektlatlan lakossgi hulladkkal egytt kidobni. A cmke azt jelli, hogy az adott termk kidobsakor a szokvnyos hztartsi hulladkelszlltsi rendszerektl elklntett eljrst kell alkalmazni. Az n felelssge, hogy ezt, s ms elektromos s elektronikus berendezseit a kormnyzati vagy a helyi hatsgok ltal kijellt gyjtredszereken keresztl szmolja fel. A megfelel hulladkfeldolgozs segt a krnyezetre s az emberi egszsgre potencilisan rtalmas negatv hatsok megelzsben. Ha elavult berendezseinek felszmolshoz tovbbi rszletes informcira van szksge, krjk, lpjen kapcsolatba a helyi hatsgokkal, a hulladkfeldolgozsi szolglattal, vagy azzal zlettel, ahol a termket vsrolta. Nederlands (Dutch) - Mleu-nformate voor klanten
n de Europese Une De Europese Richtlijn 2002/96/EC schrijft voor dat apparatuur die is voorzien van dit symbool op het product of de verpakking, niet mag worden ingezameld met niet-gescheiden huishoudelijk afval. Dit symbool geeft aan dat het product apart moet worden ingezameld. U bent zelf verantwoordelijk voor de vernietiging van deze en andere elektrische en elektronische apparatuur via de daarvoor door de landelijke of plaatselijke overheid aangewezen inzamelingskanalen. De juiste vernietiging en recycling van deze apparatuur voorkomt mogelijke negatieve gevolgen voor het milieu en de gezondheid. Voor meer informatie over het vernietigen van uw oude apparatuur neemt u contact op met de plaatselijke autoriteiten of afvalverwerkingsdienst, of met de winkel waar u het product hebt aangeschaft. Norsk (Norwegan) - Mljnformasjon for kunder EU EU-direktiv 2002/96/EF krever at utstyr med flgende symbol avbildet p produktet og/eller pakningen, ikke m kastes sammen med usortert avfall. Symbolet indikerer at dette produktet skal hndteres atskilt fra ordinr avfallsinnsamling for husholdningsavfall. Det er ditt ansvar kvitte deg med dette produktet og annet elektrisk og elektronisk avfall via egne innsamlingsordninger slik myndighetene eller kommunene bestemmer. Korrekt avfallshndtering og gjenvinning vil vre med p forhindre mulige negative konsekvenser for milj og helse. For nrmere informasjon om hndtering av det kasserte utstyret ditt, kan du ta kontakt med kommunen, en innsamlingsstasjon for avfall eller butikken der du kjpte produktet. Polsk (Polsh) - Informacja dla klentw w Un
Europejskej o przepsach dotyczcych ochrony rodowska Dyrektywa Europejska 2002/96/EC wymaga, aby sprzt oznaczony symbolem znajdujcym si na produkcie i/lub jego opakowaniu nie by wyrzucany razem z innymi niesortowanymi odpadami komunalnymi. Symbol ten wskazuje, e produkt nie powinien by usuwany razem ze zwykymi odpadami z gospodarstw domowych. Na Pastwu spoczywa obowizek wyrzucania innych urzdze elektrycznych oraz elektronicznych w punktach odbioru wyznaczonych przez wadze krajowe lub lokalne. Pozbywanie si sprztu we waciwy sposb i jego recykling pomog zapobiec potencjalnie negatywnym konsekwencjom dla rodowiska i zdrowia ludzkiego. W celu uzyskania szczegowych informacji o usuwaniu starego sprztu, prosimy zwrci si do lokalnych wadz, sub oczyszczania miasta lub sklepu, w ktrym produkt zosta nabyty. tego i Wreless-G Exteror Access Pont wth Power Over Ethernet
9 Appendx E Warranty and Regulatory Information Portugus (Portuguese) - Informao ambental para clentes da Uno Europea A Directiva Europeia 2002/96/CE exige que o equipamento que exibe este smbolo no produto e/ou na sua embalagem no seja eliminado junto com os resduos municipais no separados. O smbolo indica que este produto deve ser eliminado separadamente dos resduos domsticos regulares. da sua responsabilidade eliminar este e qualquer outro equipamento elctrico e electrnico atravs dos instalaes de recolha designadas pelas autoridades governamentais ou locais. A eliminao e reciclagem correctas ajudaro a prevenir as consequncias negativas para o ambiente e para a sade humana. Para obter informaes mais detalhadas sobre a forma de eliminar o seu equipamento antigo, contacte as autoridades locais, os servios de eliminao de resduos ou o estabelecimento comercial onde adquiriu o produto. Romn (Romanan) - Informa de medu pentru clen dn Ununea European Directiva european 2002/96/CE impune ca echipamentele care prezint acest simbol pe produs i/sau pe ambalajul acestuia s nu fie casate mpreun cu gunoiul menajer municipal. Simbolul indic faptul c acest produs trebuie s fie casat separat de gunoiul menajer obinuit. Este responsabilitatea dvs. s casai acest produs i alte echipamente electrice i electronice prin intermediul unitilor de colectare special desemnate de guvern sau de autoritile locale. Casarea i reciclarea corecte vor ajuta la prevenirea potenialelor consecine negative asupra sntii mediului i a oamenilor. Pentru mai multe informaii detaliate cu privire la casarea acestui echipament vechi, contactai autoritile locale, serviciul de salubrizare sau magazinul de la care ai achiziionat produsul. Slovenna (Slovak) - Informce o ochrane votnho prostreda pre zkaznkov v Eurpskej n
Poda eurpskej smernice 2002/96/ES zariadenie s tmto symbolom na produkte a/alebo jeho balen nesmie by likvidovan spolu s netriedenm komunlnym odpadom. Symbol znamen, e produkt by sa mal likvidova oddelene od benho odpadu z domcnost. Je vaou povinnosou likvidova toto i ostatn elektrick a elektronick zariadenia prostrednctvom pecializovanch zbernch zariaden urench vldou alebo miestnymi orgnmi. Sprvna likvidcia a recyklcia pome zabrni prpadnm negatvnym dopadom na ivotn prostredie a zdravie ud. Ak mte zujem o podrobnejie informcie o likvidcii starho zariadenia, obrte sa, prosm, na miestne orgny, organizcie zaoberajce sa likvidciou odpadov alebo obchod, v ktorom ste si produkt zakpili. Slovenna (Slovene) - Okoljske nformacje za stranke v Evropsk unj
Evropska direktiva 2002/96/EC prepoveduje odlaganje opreme, oznaene s tem simbolom na izdelku in/ali na embalai med obiajne, nerazvrene odpadke. Ta simbol opozarja, da je treba izdelek odvrei loeno od preostalih gospodinjskih odpadkov. Vaa odgovornost je, da to in preostalo elektrino in elektronsko opremo odnesete na posebna zbiralia, ki jih doloijo dravne ustanove ali lokalna uprava. S pravilnim odlaganjem in recikliranjem boste prepreili morebitne kodljive vplive na okolje in zdravje ljudi. e elite izvedeti ve o odlaganju stare opreme, se obrnite na lokalno upravo, odpad ali trgovino, kjer ste izdelek kupili. Suom (Fnnsh) - Ymprst koskeva tetoja EU-
alueen asakkalle EU-direktiivi 2002/96/EY edellytt, ett jos laitteistossa on tm symboli itse tuotteessa ja/tai sen pakkauksessa, laitteistoa ei saa hvitt lajittelemattoman yhdyskuntajtteen mukana. Symboli merkitsee sit, ett tm tuote on hvitettv erilln tavallisesta kotitalousjtteest. Sinun vastuullasi on hvitt tm elektroniikkatuote ja muut vastaavat elektroniikkatuotteet tuotteet viranomaisten mrmn viemll keryspisteeseen. Laitteiston oikea hvittminen est mahdolliset kielteiset vaikutukset ympristn ja ihmisten terveyteen. Listietoja vanhan laitteiston oikeasta hvitystavasta saa paikallisilta viranomaisilta, jtteenhvityspalvelusta tai siit myymlst, josta ostit tuotteen. tuote tai Svenska (Swedsh) - Mljnformaton fr kunder
Europeska unonen Det europeiska direktivet 2002/96/EC krver att utrustning med denna symbol p produkten och/eller frpackningen inte fr kastas med osorterat kommunalt avfall. Symbolen visar att denna produkt br kastas efter att den avskiljts frn vanligt hushllsavfall. Det faller p ditt ansvar att kasta denna och annan elektrisk och elektronisk utrustning p faststllda insamlingsplatser utsedda av regeringen eller lokala myndigheter. Korrekt kassering och tervinning skyddar mot eventuella negativa konsekvenser fr miljn och personhlsa. Fr mer detaljerad information om kassering av din gamla utrustning kontaktar du dina lokala myndigheter, avfallshanteringen eller butiken dr du kpte produkten. WEB: For additional information, please visit www.lnksys.com Wreless-G Exteror Access Pont wth Power Over Ethernet
0 Appendx F Contact Information Appendx F:
Contact Informaton Lnksys Contact Informaton Website E-Mail FTP Site http://www.linksys.com support@linksys.com ftp.linksys.com Advice Line 800-546-5797 (LINKSYS) Support 800-326-7114
(Return Merchandise RMA Authorization) 949-823-3000 Fax 949-823-3002 NOTE: Details on warranty and RMA issues can be found in the Warranty and Regulatory Information section of this Guide. Wreless-G Exteror Access Pont wth Power Over Ethernet 7041210NC-RR
frequency | equipment class | purpose | ||
---|---|---|---|---|
1 | 2007-05-04 | 2412 ~ 2462 | DTS - Digital Transmission System | Original Equipment |
app s | Applicant Information | |||||
---|---|---|---|---|---|---|
1 | Effective |
2007-05-04
|
||||
1 | Applicant's complete, legal business name |
LINKSYS LLC
|
||||
1 | FCC Registration Number (FRN) |
0008067837
|
||||
1 | Physical Address |
121 Theory Drive
|
||||
1 |
Irvine, California 92617
|
|||||
1 |
United States
|
|||||
app s | TCB Information | |||||
1 | TCB Application Email Address |
c******@curtis-straus.com
|
||||
1 | TCB Scope |
A4: UNII devices & low power transmitters using spread spectrum techniques
|
||||
app s | FCC ID | |||||
1 | Grantee Code |
Q87
|
||||
1 | Equipment Product Code |
WAP200E
|
||||
app s | Person at the applicant's address to receive grant or for contact | |||||
1 | Name |
J**** H******
|
||||
1 | Title |
Regulatory Compliance Manager
|
||||
1 | Telephone Number |
949-2********
|
||||
1 | Fax Number |
949-2********
|
||||
1 |
j******@belkin.com
|
|||||
app s | Technical Contact | |||||
1 | Firm Name |
Advance Data Technology Corporation (Hwa Ya)
|
||||
1 | Name |
G**** C****
|
||||
1 | Physical Address |
No. 19, Hwa Ya 2nd Rd., Kwei Shan Hsiang
|
||||
1 |
Taoyuan Hsien, 333
|
|||||
1 |
Taiwan
|
|||||
1 | Telephone Number |
886-3******** Extension:
|
||||
1 | Fax Number |
886-3********
|
||||
1 |
G******@adt.com.tw
|
|||||
app s | Non Technical Contact | |||||
1 | Firm Name |
Advance Data Technology Corporation
|
||||
1 | Name |
E******** W****
|
||||
1 | Physical Address |
No. 19, Hwa Ya 2nd Rd., Kwei Shan Hsiang
|
||||
1 |
Taoyuan Hsien, 333
|
|||||
1 |
Taiwan
|
|||||
1 | Telephone Number |
886-3******** Extension:
|
||||
1 | Fax Number |
886-3********
|
||||
1 |
e******@adt.com.tw
|
|||||
app s | Confidentiality (long or short term) | |||||
1 | Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | Yes | ||||
1 | Long-Term Confidentiality Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | No | ||||
if no date is supplied, the release date will be set to 45 calendar days past the date of grant. | ||||||
app s | Cognitive Radio & Software Defined Radio, Class, etc | |||||
1 | Is this application for software defined/cognitive radio authorization? | No | ||||
1 | Equipment Class | DTS - Digital Transmission System | ||||
1 | Description of product as it is marketed: (NOTE: This text will appear below the equipment class on the grant) | Wireless-G Exterior Access Point with POE | ||||
1 | Related OET KnowledgeDataBase Inquiry: Is there a KDB inquiry associated with this application? | No | ||||
1 | Modular Equipment Type | Does not apply | ||||
1 | Purpose / Application is for | Original Equipment | ||||
1 | Composite Equipment: Is the equipment in this application a composite device subject to an additional equipment authorization? | No | ||||
1 | Related Equipment: Is the equipment in this application part of a system that operates with, or is marketed with, another device that requires an equipment authorization? | No | ||||
1 | Grant Comments | Output Power listed is conducted. This device must be professionally installed. Marketing to the General Public is prohibited. Only those antenna(s) tested with the device or similar antenna(s) with equal or lesser gain may be used with this transmitter. The use of other antenna requires a Class II Permissive Change filing. The antennas used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. End -users and installers must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance. | ||||
1 | Is there an equipment authorization waiver associated with this application? | No | ||||
1 | If there is an equipment authorization waiver associated with this application, has the associated waiver been approved and all information uploaded? | No | ||||
app s | Test Firm Name and Contact Information | |||||
1 | Firm Name |
Bureau Veritas CPS (H.K.) Ltd. Taoyuan Branch
|
||||
1 | Name |
R******** C****
|
||||
1 | Telephone Number |
886-3******** Extension:
|
||||
1 | Fax Number |
886-3********
|
||||
1 |
r******@tw.bureauveritas.com
|
|||||
Equipment Specifications | |||||||||||||||||||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
1 | 1 | 15C | 20 | 2412.00000000 | 2462.00000000 | 0.1430000 |
some individual PII (Personally Identifiable Information) available on the public forms may be redacted, original source may include additional details
This product uses the FCC Data API but is not endorsed or certified by the FCC