FCC ID: Q87-WU54GPV4 Wireless-G Portable USB Adapter

Date: July 5, 2004 Cisco-Linksys, LLC 121 Theory Drive Irvine, CA 92612 (USA) Phone: 949-823-3188 Fax: 949-823-3002 FEDERAL COMMUNICATIONS COMMISSION DECLARATION OF CONFORMITY (DoC) Cisco-Linksys, LLC declares that the equipment described in this document is within the requirements of the Code of Federal Regulations listed below:

Product Name: Wireless-G Portable USB Adapter Model Number: WUSB54GP ver. 4 This device complies with the limits for a Class B digital device pursuant to IEEE ANSI C63.4 and FCC Part 15 subpart B of the Rules and Regulations. The test result has been shown in the ADT test report with numbered D930629L11. Operation is subject to the following two conditions:

1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation. The Part 15 radio device operates on a non-interference basis with other devices operation at this frequency. Any change or modification to the product not expressly approved by Linksys could void the users authority to operate the device. Jennifer Yu / Associate Engineer Cisco-Linksys, LLC Tel.: ( 949 ) 823-3188 Fax: ( 949 ) 823-3002 jennyu@cisco.com

A Division of Cisco Systems, Inc. 2.4802.11g GHz WIRELESS Wireless-G Portable USB Adapter User Guide Model No. WUSB54GP v4 Linksys is a registered trademark or trademark of Cisco Systems, Inc. and/or its affiliates in the U.S. and certain other countries. Wireless-G Portable USB Adapter Copyright and Trademarks Specifications are subject to change without notice. Linksys is a registered trademark or trademark of Cisco Systems, Inc. and/or its affiliates in the U.S. and certain other countries. Copyright 2004 Cisco Systems, Inc. All rights reserved. Other brands and product names are trademarks or registered trademarks of their respective holders. How to Use this User Guide This User Guide has been designed to make understanding networking with the Wireless-G Portable USB Adapter easier than ever. Look for the following items when reading this User Guide:

This checkmark means there is a Note of interest and is something you should pay special attention to while using the Wireless-G Portable USB Adapter. This exclamation point means there is a Caution or warning and is something that could damage your property or the Wireless-G Portable USB Adapter. This question mark provides you with a reminder about something you might need to do while using the Wireless-G Portable USB Adapter. In addition to these symbols, there are definitions for technical terms that are presented like this:

word: definition. Also, each figure (diagram, screenshot, or other image) is provided with a figure number and description, like this:

Figure 0-1: Sample Figure Description Figure numbers and descriptions can also be found in the "List of Figures" section in the Table of Contents. Wireless-G Portable USB Adapter Table of Contents Chapter 1: Introduction Welcome Whats in this Guide?

Chapter 2: Planning your Wireless Network Network Topology Roaming Network Layout Chapter 3: Software Installation and Configuration for Windows 2000 Chapter 4: Connecting the Portable USB Adapter Using the USB Extension Base Chapter 5: Driver Installation for Windows XP Windows XP Wireless Zero Configuration Chapter 6: Using the WLAN Monitor Overview Accessing the WLAN Monitor The Link Information Tab The Site Survey Tab The Profiles Tab Creating a New Profile Appendix A: Troubleshooting Common Problems and Solutions Frequently Asked Questions Security Precautions Security Threats Facing Wireless Networks Appendix B: Wireless Security Appendix C: Windows Help Appendix D: Glossary Appendix E: Specifications Appendix F: Warranty Information Appendix G: Regulatory Information Appendix H: Contact Information 1 1 2 4 4 4 5 6 10 11 12 13 15 15 15 15 17 18 20 24 24 25 28 28 28 31 32 35 37 38 39 Wireless-G Portable USB Adapter Appendix I: Windows Help Appendix J: Glossary Appendix K: Specifications Appendix L: Warranty Information Appendix M: Regulatory Information Appendix N: Contact Information 31 32 35 37 38 39 Wireless-G Portable USB Adapter List of Figures Figure 3-1: The Setup Wizards Welcome Screen Figure 3-2: The License Agreement Screen Figure 3-3: The Wireless Mode Screen Figure 3-4: The Ad-Hoc Mode Settings Screen Figure 3-5: The Wireless Security Screen Figure 3-6: The Check Settings Screen Figure 3-7: The Congratulations Screen Figure 4-1: The Portable USB Adapter on Your Laptop Figure 4-2: A USB Port Figure 4-3: The Windows 2000 Digital Signature Screen Figure 5-1: XP Setup Welcome Screen Figure 5-2: Windows logo testing screen Figure 5-3: New Hardware Found screen Figure 5-4: Windows XP Wireless Zero Configuration icon Figure 5-5: Network Connection - No WEP Figure 5-6: Network Connection - WEP Figure 5-7: Optional Settings Figure 6-1: The Wireless Icon Figure 6-2: The Link Information Tab Figure 6-3: The Link Information Tab - More Information Figure 6-4: The Site Survey Tab Figure 6-5: The Profiles Tab Figure 6-6: Importing a Profile Figure 6-7: Optional Settings Figure 6-8: The Profiles Tab Figure 6-9: Create Connection Profile Figure 6-10: Profiles - Network Settings Figure 6-11: Profiles - Wireless Mode Figure 6-12: Profiles - Ad-Hoc Settings Figure 6-13: Profiles - Security Settings 6 7 7 8 8 9 9 10 10 11 12 12 12 13 13 14 14 15 15 16 17 18 19 19 20 20 21 21 22 22 Wireless-G Portable USB Adapter Figure 6-14: Profiles - Confirm New Settings Figure 6-15: Profiles - Congratulations 23 23 Wireless-G Portable USB Adapter Chapter 1: Introduction Welcome Thank you for choosing the Wireless-G Portable USB Adapter. With this Adapter, your wireless networking experience will be faster and easier than ever. network: a series of computers or devices connected for the purpose of data sharing, storage, and/or transmission between users. adapter: a device that adds network functionality to your PC. How does the Adapter do this? Like all wireless products, the Adapter allows for greater range and mobility within your wireless network. Connecting to your PC via the USB port means that this Adapter leaves the PCs slots open for other purposes. This adapter communicates over the 802.11g wireless standard, one of the newest wireless standards, to communicate with your network. 802.11g: an IEEE wireless networking standard that specifies a maximum data transfer rate of 54Mbps, an operating frequency of 2.4GHz, and backward compatibility with 802.11b devices. But what does all of this mean?

Networks are useful tools for sharing computer resources. You can access one printer from different computers and access data located on another computer's hard drive. Networks are even used for playing multiplayer video games. So, networks are not only useful in homes and offices, they can also be fun. PCs equipped with wireless cards and adapters can communicate without cumbersome cables. By sharing the same wireless settings, within their transmission radius, they form a wireless network. Use the instructions in this Guide to help you connect the Adapter, set it up, and configure it for your network. These instructions should be all you need to get the most out of the Adapter. Chapter 1: Introduction Welcome 1 Wireless-G Portable USB Adapter Whats in this Guide?

This user guide covers the steps for setting up and using the Wireless-B USB Network Adapter.

Chapter 1: Introduction This chapter describes the Adapters applications and this User Guide.

Chapter 2: Planning Your Wireless Network This chapter discusses a few of the basics about wireless networking.

Chapter 3: Software Installation and Configration for Windows 2000 This chapter instructs you on how to install the Adapters Setup Wizard and Configure the Adapter for Windows 2000.

Chapter 4: Connecting the Portable USB Adapter This chapter shows you how to connect the Adapter to your PCs USB port.

Chapter 5: Driver Installation and Configuration for Windows XP This chapter explains how to install the Adapters driver and use Windows Zero Configuration.

Chapter 6: Using the WLAN Monitor This chapter show you how to use the Adapters WLAN Monitor.

Appendix A: Troubleshooting This appendix describes some problems and solutions, as well as frequently asked questions, regarding installation and use of the Adapter.

Appendix B: Wireless Security This appendix discusses security issues regarding wireless networking and measures you can take to help protect your wireless network.

Appendix C: Windows Help This appendix describes how you can use Windows Help for instructions about networking, such as installing the TCP/IP protocol.

Appendix D: Glossary This appendix gives a brief glossary of terms frequently used in networking.

Appendix E: Specifications This appendix provides the Adapters technical specifications. Chapter 1: Introduction Whats in this Guide?

2 Wireless-G Portable USB Adapter

Appendix F: Warranty Information This appendix supplies the Adapters warranty information.

Appendix G: Regulatory Information This appendix supplies the Adapters regulatory information.

Appendix H: Contact Information This appendix provides contact information for a variety of Linksys resources, including Technical Support. Chapter 1: Introduction Whats in this Guide?

3 Wireless-G Portable USB Adapter Chapter 2: Planning your Wireless Network Network Topology A wireless network is a group of computers, each equipped with one wireless adapter. Computers in a wireless network must be configured to share the same radio channel. Several PCs equipped with wireless cards or adapters can communicate with one another to form an ad-hoc network. ad-hoc: a group of wireless devices communicating directly with each other (peer-

to-peer) without the use of an access point Linksys wireless adapters also provide users access to a wired network when using an access point or wireless router. An integrated wireless and wired network is called an infrastructure network. Each wireless PC in an infrastructure network can talk to any computer in a wired network infrastructure via the access point or wireless router. An infrastructure configuration extends the accessibility of a wireless PC to a wired network, and can double the effective wireless transmission range for two wireless adapter PCs. Since an access point is able to forward data within a network, the effective transmission range in an infrastructure network can be doubled. Roaming Infrastructure mode also supports roaming capabilities for mobile users. Roaming means that you can move your wireless PC within your network and the access points will pick up the wireless PC's signal, providing that they both share the same channel and SSID. Before enabling you consider roaming, choose a feasible radio channel and optimum access point position. Proper access point positioning combined with a clear radio signal will greatly enhance performance. access point: device that allows wireless-

equipped computers and other devices to communicate with a wired network. infrastructure: Configuration in which a wireless network is bridged to a wired network via an access point. roaming: the ability to take a wireless device from one access point's range to another without losing the connection. ssid: your wireless networks name Chapter 2: Planning your Wireless Network Network Topology 4 Wireless-G Portable USB Adapter Network Layout Linksys wireless access points and wireless routers have been designed for use with 802.11a, 802.11b, and 802.11g products. With 802.11g products communicating with the 802.11b standard and some products incorporating both a and g, products using these standards can communicate with each other. Access points and wireless routers are compatible with 802.11a, 802.11b and 802.11g adapters, such at the PC Cards for your laptop computers, PCI Card for your desktop PC, and USB Adapters for when you want to enjoy USB connectivity. Wireless products will also communicate with the wireless PrintServer. When you wish to connect your wired network with your wireless network, network ports on access points and wireless routers can be connected to any of Linksys's switches or routers. With these, and many other, Linksys products, your networking options are limitless. Go to the Linksys website at www.linksys.com for more information about wireless products. 802.11b: an IEEE wireless networking standard that specifies a maximum data transfer rate of 11Mbps and an operating frequency of 2.4GHz. switch: device that is the central point of connection for computers and other devices in a network, so data can be shared at full transmission speeds. router: a networking device that connects multiple networks together, such as a local network and the Internet. Chapter 2: Planning your Wireless Network Network Layout 5 Wireless-G Portable USB Adapter Chapter 3: Software Installation and Configuration for Windows 2000 IMPORTANT: You must run the Setup Wizard to install the software before connecting the Adapter. If you are running Windows XP, connect the Adapter as shown in Chapter 4 and proceed to Chapter 5. The Wireless-G Portable USB Adapter Setup Wizard will guide you through the installation procedure. The Setup Wizard will install the WLAN Monitor and driver, as well as configure the Adapter. 1. Insert the Setup Wizard CD-ROM into your CD-ROM drive. The Setup Wizard should run automatically, and the Welcome screen should appear. If it does not, click the Start button and choose Run. In the field that appears, enter D:\setup.exe (if D is the letter of your CD-ROM drive). Figure 3-1: The Setup Wizards Welcome Screen Chapter 3: Software Installation and Configuration for Windows 2000 6 Wireless-G Portable USB Adapter 2. Read the License Agreement displayed on the following screen and click the Next button to continue the installation. If you click the Cancel button, you will end the installation. 3. The Wireless Mode screen will ask for some information about your wireless network. In the SSID field, enter your networks SSID (Service Set Identifier). The SSID is your network name and must be identical for all devices in the network. The default setting is linksys (all lowercase). Next, choose a wireless mode. Click the Infrastructure Mode radio button if you want your wireless computers to network with computers on your wired network using an access point. Click the Ad-Hoc Mode radio button if you want multiple wireless computers to network directly with each other. Click the Next button to continue, or click the Back button to return to the previous page. Figure 3-2: The License Agreement Screen Figure 3-3: The Wireless Mode Screen Chapter 3: Software Installation and Configuration for Windows 2000 7 Wireless-G Portable USB Adapter 4. If you chose Infrastructure Mode, go to Step 5 now. If you chose Ad-Hoc Mode, select the correct operating channel for your network from the Channel drop-down menu. Then, select the Network Mode from the drop-

down menu. Click the Next button, and go to Step 5. Click the Back button to change any settings. Channel - The channel you choose should match the channel set on the other devices in your wireless network. If you are unsure about which channel to use, select the default channel (Channel 6). Network Mode - Keep the default setting, Mixed, if you have Wireless-G and Wireless-B devices in your network. Select G-Only if you have only Wireless-G devices in your network. 5. The Wireless Security screen allows you to set the security level for your network. Enable or disable Wired Equivalent Privacy (WEP) encryption for your wireless network. If you enable WEP, enter a Passphrase or WEP key. Click the Next button to continue or the Back button to return to the previous screen. For more information about the information on this screen, you can also click the Help button. Figure 3-4: The Ad-Hoc Mode Settings Screen WEP - If you do not want to use WEP encryption, choose Disabled. To use WEP encryption (recommended to increase network security), select 64-bit or 128-bit WEP from the drop-down menu, and enter either a Passphrase or WEP key. Passphrase - Instead of manually entering WEP keys, you can enter a Passphrase, so that a WEP key is automatically generated. It is case-sensitive and should not be longer than 16 alphanumeric characters. This passphrase must match the passphrase of your wireless network and is compatible with other Linksys wireless products only. (If you have any non-Linksys wireless products, enter the WEP key(s) manually on those products.) WEP Key - This WEP key must match the WEP key of your wireless network. If you are using 64-bit WEP encryption, then the key must consist of exactly ten hexadecimal characters. If you are using 128-bit WEP encryption, then the key must consist of exactly 26 hexadecimal characters. Valid hexadecimal characters are 0 to 9 and A to F. TX Key - This allows you to access different WEP keys used by different routers or access points in your network. Choose the TX Key used in that network. For instance, if the device uses TX Key 3, use TX Key 3. If youre not using multiple WEP Keys, leave this set at 1. Authentication - Select the Authentication method used by your network. Open Authentication does not employ WEP keys. Shared Authentication employs WEP encryption. Auto (the default setting) chooses the method of the network to which you're connecting. Figure 3-5: The Wireless Security Screen Chapter 3: Software Installation and Configuration for Windows 2000 8 Wireless-G Portable USB Adapter 6. At this point, a screen stating that a digital signature was not found may appear. This software has been tested and found to work properly with Windows 2000. Click the Yes button to continue installation. 7. The Setup Wizard will ask you to review your settings before it starts to copy files. Click the Next button to save these settings, or click the Back button to change any settings. 8. After the files have been successfully copied, the Congratulations screen will appear. Click the Exit button. Figure 3-6: The Check Settings Screen Now that the software installation is complete, proceed to Chapter 4: Connecting the Wireless-G Portable USB Adapter. Figure 3-7: The Congratulations Screen software: instructions for the computer Chapter 3: Software Installation and Configuration for Windows 2000 9 Wireless-G Portable USB Adapter Chapter 4: Connecting the Portable USB Adapter 1. To connect the Portable USB Adapter to your PC, simply plug the USB end into your PCs available USP port. Figure 4-1: The Portable USB Adapter on Your Laptop IMPORTANT: Windows 2000 users must run the Setup Wizard to install the software before connecting the Portable USB Adapter. IMPORTANT: Windows XP users must connect the Portable USB Adapter before installing the software, shown in Chapter 5. Figure 4-2: A USB Port port: the connection point on a computer or networking device used for plugging in a cable or an adapter. Chapter 4: Connecting the Portable USB Adapter 10 Wireless-G Portable USB Adapter 2. When Windows 2000 begins installing the Network Adapters driver file, a screen stating that a digital signature was not found may appear. This software has been tested and found to work properly with Windows 2000. Click the Yes button to continue installation. If your PC is running Windows XP, proceed to Chapter 5: Driver Installation for Windows XP. If your PC is running Windows 2000, the installation of the Wireless-G Portable USB Adapter is complete. If you want to check the link information, search for available wireless networks, or make additional configuration changes, proceed to Chapter 6: Using the WLAN Monitor. Figure 4-3: The Windows 2000 Digital Signature Screen Using the USB Extension Base For better reception on the Portable USB Adapter, you can attach the USB Extension Base to your PCs USB port and connect the Portable USB Adapter to the USB Extension Base. Then, you can place the USB Extension Base more strategically, on a higher platform or away from interference, for better reception. Chapter 4: Connecting the Portable USB Adapter Using the USB Extension Base 11 Wireless-G Broadband Router Chapter 5: Driver Installation for Windows XP After connecting the Adapter to your PC, as shown in Chapter 4, youll need to install the driver. Windows XP will automatically detect the Adapter. Insert the Setup CD-ROM into the CD-ROM drive. Click the radio button next to Install the software automatically (Recommended). Then, click the Next button. Figure 5-1: XP Setup Welcome Screen A Windows logo testing screen may appear, asking if you wish to discontinue installation. This software has been tested and found to work properly with Windows XP. Click the Continue Anyway button to continue installation. The next screen shows that the Wizard is complete. Click the Finish button. The drivers are now installed. Figure 5-2: Windows logo testing screen Chapter 5: Driver Installation for Windows XP Figure 5-3: New Hardware Found screen 12 Wireless-G Broadband Router Windows XP Wireless Zero Configuration 1. After installing the Adapter, the Windows XP Wireless Zero Configuration icon will appear in your computers system tray. Double-click the icon. NOTE: Windows XP has a built-in configuration tool. Use Windows XP Wireless Zero Configuration (in the system tray at the bottom of your screen) to configure the Adapter. Figure 5-4: Windows XP Wireless Zero Configuration icon NOTE: Steps 2 and 3 are the instructions and screenshots for Windows XP with Service Pack 1 installed. If you have not installed Service Pack 1, select the network you want, and click the Connect button. If the network has WEP encryption enabled, enter the WEP key in the Network key field, and then click the Connect button. 2. The screen that appears will show any available wireless network. Select the network you want. If this network has WEP encryption enabled, go to step 3. If this network does not have WEP encryption enabled, you will be asked to select a network. Make sure the box next to Allow me to connect to the selected wireless network, even though it is not secure is checked. Then, click the Connect button, and go to step 4. Chapter 5: Driver Installation for Windows XP Windows XP Wireless Zero Configuration Figure 5-5: Network Connection - No WEP 13 Wireless-G Broadband Router 3. If WEP is enabled, you will be asked to enter the network (WEP) key. Enter the WEP key of your wireless network in the Network key field, and re-enter it in the Confirm network key field. Then, click the Connect button, and proceed to step 4. Figure 5-6: Network Connection - WEP NOTE: Windows XP Wireless Zero Configuration does not support the use of a passphrase. Enter the exact WEP key used by your access point. 4. The Zero Configuration icon, showing a connection, will appear if your connection is active. Figure 5-7: Optional Settings For more information about wireless networking on a Windows XP computer, click the Start button, select Help, and choose Support. Enter the keyword wireless in the field provided, and press the Enter key. Congratulations! The installation of the Wireless-G USB Network Adapter is complete. Chapter 5: Driver Installation for Windows XP Windows XP Wireless Zero Configuration 14 Wireless-G Portable USB Adapter Chapter 6: Using the WLAN Monitor Overview Use the WLAN Monitor to check the link information, search for available wireless networks, or create profiles that hold different configuration settings. Accessing the WLAN Monitor After installing the Adapter, the Wireless-G USB Network Adapter WLAN Monitor icon will appear in your system tray. Double-click the icon. The Link Information tab will appear. From this tab, you can find out the strength of the current wireless signal as well as its quality. You can also click the More Information button to view additional status information about the current wireless connection. To search for available wireless networks, click the Site Survey tab. To perform configuration changes, click the Profiles tab. The Link Information Tab The Link Information tab displays the signal strength and link quality information about the current connection and provides a button to click for additional status information. Ad-Hoc Mode or Infrastructure Mode - The screen indicates whether the Adapter is currently working in ad-

hoc or infrastructure mode. Signal Strength - The Signal Strength bar indicates the signal strength. Link Quality - The Link Quality bar indicates the quality of the wireless network connection. Figure 6-1: The Wireless Icon Click the More Information button to view more information about the wireless network connection. Figure 6-2: The Link Information Tab Click the X (Close) button in the upper right corner to exit the WLAN Monitor. Chapter 5: Using the WLAN Monitor Overview 15 Wireless-G Portable USB Adapter Clicking the More Information button displays much more information about the Adapters connection, as shown below:

Wireless Network Status Status - The status of the wireless network connection. SSID - The unique name of the wireless network. Wireless Mode - The mode of the wireless network currently in use. Transfer Rate - The data transfer rate of the current connection. Channel - The channel to which the wireless network devices are set. WEP - The status of the WEP encryption security feature. MAC - The MAC address of the wireless networks access point. TCP/IP Setting IP Address - The IP Address of the Adapter. Subnet Mask - The Subnet Mask of the Adapter. Default Gateway - The Default Gateway address of the Adapter. DNS - The DNS address of the Adapter. DHCP - The status of the DHCP client. Signal Strength - The Signal Strength bar indicates the signal strength. Link Quality - The Link Quality bar indicates the quality of the wireless network connection. Click the Back button to return to the initial Link Information tab. Click the X (Close) button in the upper right corner to exit the WLAN Monitor. Chapter 5: Using the WLAN Monitor The Link Information Tab wep: a method of encrypting data transmitted on a wireless network for greater security. Figure 6-3: The Link Information Tab - More Information encryption: encoding data to prevent it from being read by unauthorized people ip address: the address used to identify a computer or device on a network subnet mask: an address code that determines the size of a network default gateway: a device that forwards Internet traffic from your local area network dns: the IP address of your ISP's server, which translates the names of websites into IP addresses. dhcp: a protocol that lets one device on a local network, known as a DHCP server, assign temporary IP addresses to the other network devices, typically computers. 16 Wireless-G Portable USB Adapter The Site Survey Tab The Site Survey tab displays available networks and allows you to connect to them. The information about these networks are displayed as below:

SSID - The SSID or unique name of the wireless network. CH - The channel upon which the network broadcasts. Signal - The percentage of signal strength, from 0 to 100%. Site Information SSID - The SSID or unique name of the wireless network. Wireless Mode - The mode of the wireless network currently in use. Channel - The channel to which the wireless network devices are set. WEP - The status of the WEP encryption security feature. MAC - The MAC address of the wireless networks access point. Refresh - Click the Refresh button to perform a new search for wireless devices. Connect - To connect to one of the networks on the list, select the wireless network, and click the Connect button. If the wireless network has WEP encryption enabled, you will need to configure WEP encryption with that network. Figure 6-4: The Site Survey Tab mac: the unique address that a manufacturer assigns to each networking device Chapter 5: Using the WLAN Monitor The Site Survey Tab 17 Wireless-G Portable USB Adapter The Profiles Tab The Profiles screen lets you save different configuration profiles for different network setups. You can also import or export profiles. The default profile holds the initial configuration saved when you ran the Setup Wizard. Profile - Name of the connection profile. SSID - The wireless networks unique name, as set in the connection profile. Profile Information Wireless Mode - The mode of the wireless network currently in use. Transfer Rate - The data transfer rate of the current connection. (In Auto mode, the Adapter dynamically shifts to the fastest data transfer rate possible at any given time.) Figure 6-5: The Profiles Tab Channel - The channel to which the wireless network devices are set. WEP - The status of the WEP encryption security feature. Authentication - The authentication setting for the network. Connect - To connect to a wireless network using a specific profile, select the profile, and click the Connect button. New - Click the New button to create a new profile. See the next section, Creating a New Profile, for detailed instructions. Edit - Select a profile, and click the Edit button to change an existing profile. Chapter 5: Using the WLAN Monitor The Profiles Tab 18 Wireless-G Portable USB Adapter Import - Click the Import button to import a profile that has been saved in another location. Select the appropriate file and click the Open button. Export - To save the profile(s) in a different location, click the Export button. Direct Windows to the appropriate folder and click the OK button. Figure 6-6: Importing a Profile Figure 6-7: Optional Settings Delete - Click the Delete button to delete a profile. Click the X (Close) button in the upper right corner to exit the WLAN Monitor. Chapter 5: Using the WLAN Monitor The Profiles Tab 19 Wireless-G Portable USB Adapter Creating a New Profile 1. On the Profiles tab, click the New button to create a new profile. 2. When the Create connection profile screen appears, enter a name for the new profile. Click OK to save the profile name or click Cancel to return to the previous screen. Figure 6-8: The Profiles Tab Figure 6-9: Create Connection Profile Chapter 5: Using the WLAN Monitor Creating a New Profile 20 Wireless-G Portable USB Adapter 3. Enter your networks settings on the Network Settings screen, which appears next. If your network has a DHCP server (or Router), click the radio button next to Obtain an IP address automatically (DHCP) and click the Next button to continue. If your network does not have a DHCP server (or router), click the radio button next to Specify the IP address. Enter an IP Address, Subnet Mask, Default Gateway, and DNS appropriate for your network. Enter each address in this format: xxx.xxx.xxx.xxx (the xs represent the numbers that make up each address). You must specify the IP Address and Subnet Mask on this screen. If you are unsure about the Default Gateway and DNS addresses, then leave these fields alone. IP Address - This IP Address must be unique to your network. Subnet Mask - The Adapters Subnet Mask must be the same as your wired networks Subnet Mask. Default Gateway - Enter the IP address of your networks Gateway here. DNS - Enter the DNS addresses of your network here. Click the Next button to continue or the Cancel button to return to the previous screen. Figure 6-10: Profiles - Network Settings 4. The Wireless Mode screen shows a choice of two wireless modes. Click the Infrastructure Mode radio button if you want your wireless computers to communicate with computers on your wired network via a wireless access point. Click the Ad-Hoc Mode radio button if you want multiple wireless computers to communicate directly with each other. Click the Next button to continue or the Back button to return to the previous screen. SSID - The SSID is the unique name shared among all devices in your wireless network. The SSID must be identical for all devices in the wireless network. It is case-sensitive and must not exceed 32 alphanumeric characters, which can be any keyboard character. Infrastructure Mode - This mode allows wireless and wired networks to communicate through an access point. Ad-Hoc Mode - This mode allows wireless-equipped computers to communicate directly with each other. No access point is used. Chapter 5: Using the WLAN Monitor Creating a New Profile 21 Figure 6-11: Profiles - Wireless Mode Wireless-G Portable USB Adapter 5. The Ad-Hoc Mode Settings screen, for those who chose an Ad-hoc network, will appear next. Select the correct operating channel for your network from the Channel drop-down menu. Then, select the Network Mode from the drop-down menu. Click the Next button to continue or click the Back button to change any settings. Channel - The channel you choose should match the channel set on the other devices in your wireless network. If you are unsure about which channel to use, select the default channel (Channel 6). Network Mode - Select Mixed Mode, and both Wireless-G and Wireless-B computers will be allowed on the network, but the speed will be reduced. Select G-Only Mode for maximum speed, but no Wireless-B users will be allowed on the network. 6. The Security Settings screen allows you to set the security level for your network. Enable or disable Wired Equivalent Privacy (WEP) encryption for your wireless network. If you enable WEP, enter a Passphrase or WEP key. Click the Next button to continue or the Back button to return to the previous screen. For more information about the information on this screen, you can also click the Help button. Figure 6-12: Profiles - Ad-Hoc Settings WEP - If you do not want to use WEP encryption, choose Disabled. To use WEP encryption (recommended to increase network security), select 64-bit or 128-bit WEP from the drop-down menu, and enter either a Passphrase or WEP key. Passphrase - Instead of manually entering WEP keys, you can enter a Passphrase, so that a WEP key is automatically generated. It is case-sensitive and should not be longer than 16 alphanumeric characters. This passphrase must match the passphrase of your wireless network and is compatible with other Linksys wireless products only. (If you have any non-Linksys wireless products, enter the WEP key(s) manually on those products.) WEP Key - This WEP key must match the WEP key of your wireless network. If you are using 64-bit WEP encryption, then the key must consist of exactly ten hexadecimal characters. If you are using 128-bit WEP encryption, then the key must consist of exactly 26 hexadecimal characters. Valid hexadecimal characters are 0 to 9 and A to F. TX Key - This allows you to access different WEP keys used by different routers or access points in your network. Choose the TX Key used in that network. For instance, if the device uses TX Key 3, use TX Key 3. If youre not using multiple WEP Keys, leave this set at 1. Authentication - Select the Authentication method used by your network. Open Authentication does not employ WEP keys. Shared Authentication employs WEP encryption. Auto (the default setting) chooses the method of the network to which you're connecting. Figure 6-13: Profiles - Security Settings Chapter 5: Using the WLAN Monitor Creating a New Profile 22 Wireless-G Portable USB Adapter 7. The Confirm New Settings screen will appear. To save the new settings, click the Save button. To cancel the settings and return to the Profiles screen, click the Exit button. To edit the new settings, click the Back button. 8. The Congratulations screen shows that the new Profile has successfully been configured. Click Connect to Network to implement the new settings immediately and return to the Link Information screen. Click Return to Profiles Screen to keep the current settings active, and return to the Profiles screen so that you can edit your profile or create another profile. You have successfully created a connection profile. Click the X (Close) button in the upper right corner to exit the WLAN Monitor. Figure 6-14: Profiles - Confirm New Settings Figure 6-15: Profiles - Congratulations Chapter 5: Using the WLAN Monitor Creating a New Profile 23 Wireless-G Portable USB Adapter Appendix A: Troubleshooting This appendix provides solutions to problems usually encountered during the installation and operation of the Adapter. Read the description below to solve your problems. If you can't find an answer here, check the Linksys website at www.linksys.com. Common Problems and Solutions 1.My computer does not recognize the USB Network Adapter.

Make sure that the USB Network Adapter is properly inserted into the USB port.

Also, make sure that the USB Controller is enabled in the BIOS. Check with your motherboard User Guide for more information. 2. The USB Network Adapter does not work properly.

Reinsert the USB Network Adapter into the notebook or desktops USB port. Right-click on My Computer, and select Properties. Select the Adapter, then chose the Device Manager tab, and click on the Network Adapter. You will find the USB Network Adapter if it is installed successfully. If you see a yellow exclamation mark, the resources may be conflicting and you must follow the steps below:

Uninstall the driver software from your PC.

Restart your PC and repeat the hardware and software installation as specified in this User Guide. 3. I cannot communicate with the other computers linked via Ethernet in the Infrastructure configuration.

Make sure that the notebook or desktop is powered on.

Make sure that your USB Network Adapter is configured on the same channel, SSID, and WEP as the other computers in the Infrastructure configuration. Appendix A: Troubleshooting Common Problems and Solutions 24 Wireless-G Portable USB Adapter Frequently Asked Questions Can I run an application from a remote computer over the wireless network?

This will depend on whether or not the application is designed to be used over a network. Consult the applications user guide to determine if it supports operation over a network. Can I play computer games with other members of the wireless network?

Yes, as long as the game supports multiple players over a LAN (local area network). Refer to the games user guide for more information. What is the IEEE 802.11b standard?

It is one of the IEEE standards for wireless networks. The 802.11b standard allows wireless networking hardware from different manufacturers to communicate, provided that the hardware complies with the 802.11b standard. The 802.11b standard states a maximum data transfer rate of 11Mbps and an operating frequency of 2.4GHz. What is the IEEE 802.11g standard?

It is one of the IEEE standards for wireless networks. The 802.11g standard allows wireless networking hardware from different manufacturers to communicate, provided that the hardware complies with the 802.11g standard. The 802.11g standard states a maximum data transfer rate of 54Mbps and an operating frequency of 2.4GHz. What IEEE 802.11b features are supported?

The product supports the following IEEE 802.11b functions:

CSMA/CA plus Acknowledge protocol

Multi-Channel Roaming

Automatic Rate Selection

RTS/CTS feature

Fragmentation

Power Management What IEEE 802.11g features are supported?

The product supports the following IEEE 802.11g functions:

CSMA/CA plus Acknowledge protocol

OFDM protocol

Multi-Channel Roaming

Automatic Rate Selection

RTS/CTS feature

Fragmentation

Power Management Appendix A: Troubleshooting Frequently Asked Questions 25 Wireless-G Portable USB Adapter What is ad-hoc mode?

When a wireless network is set to ad-hoc mode, the wireless-equipped computers are configured to communicate directly with each other. The ad-hoc wireless network will not communicate with any wired network. What is infrastructure mode?

When a wireless network is set to infrastructure mode, the wireless network is configured to communicate with a wired network through a wireless access point. What is roaming?

Roaming is the ability of a portable computer user to communicate continuously while moving freely throughout an area greater than that covered by a single access point. Before using the roaming function, the workstation must make sure that it is the same channel number with the access point of dedicated coverage area. To achieve true seamless connectivity, the wireless LAN must incorporate a number of different functions. Each node and access point, for example, must always acknowledge receipt of each message. Each node must maintain contact with the wireless network even when not actually transmitting data. Achieving these functions simultaneously requires a dynamic RF networking technology that links access points and nodes. In such a system, the users end node undertakes a search for the best possible access to the system. First, it evaluates such factors as signal strength and quality, as well as the message load currently being carried by each access point and the distance of each access point to the wired backbone. Based on that information, the node next selects the right access point and registers its address. Communications between end node and host computer can then be transmitted up and down the backbone. As the user moves on, the end nodes RF transmitter regularly checks the system to determine whether it is in touch with the original access point or whether it should seek a new one. When a node no longer receives acknowledgment from its original access point, it undertakes a new search. Upon finding a new access point, it then re-registers, and the communication process continues. What is ISM band?

The FCC and their counterparts outside of the U.S. have set aside bandwidth for unlicensed use in the ISM

(Industrial, Scientific and Medical) band. Spectrum in the vicinity of 2.4 GHz, in particular, is being made available worldwide. This presents a truly revolutionary opportunity to place convenient high-speed wireless capabilities in the hands of users around the globe. What is Spread Spectrum?

Spread Spectrum technology is a wideband radio frequency technique developed by the military for use in reliable, secure, mission-critical communications systems. It is designed to trade off bandwidth efficiency for reliability, integrity, and security. In other words, more bandwidth is consumed than in the case of narrowband transmission, but the trade-off produces a signal that is, in effect, louder and thus easier to detect, provided that Appendix A: Troubleshooting Frequently Asked Questions 26 Wireless-G Portable USB Adapter the receiver knows the parameters of the spread-spectrum signal being broadcast. If a receiver is not tuned to the right frequency, a spread-spectrum signal looks like background noise. There are two main alternatives, Direct Sequence Spread Spectrum (DSSS) and Frequency Hopping Spread Spectrum (FHSS). What is DSSS? What is FHSS? And what are their differences?

Frequency-Hopping Spread-Spectrum (FHSS) uses a narrowband carrier that changes frequency in a pattern that is known to both transmitter and receiver. Properly synchronized, the net effect is to maintain a single logical channel. To an unintended receiver, FHSS appears to be short-duration impulse noise. Direct-Sequence Spread-

Spectrum (DSSS) generates a redundant bit pattern for each bit to be transmitted. This bit pattern is called a chip

(or chipping code). The longer the chip, the greater the probability that the original data can be recovered. Even if one or more bits in the chip are damaged during transmission, statistical techniques embedded in the radio can recover the original data without the need for retransmission. To an unintended receiver, DSSS appears as low power wideband noise and is rejected (ignored) by most narrowband receivers. Would the information be intercepted while transmitting on air?

WLAN features two-fold protection in security. On the hardware side, as with Direct Sequence Spread Spectrum technology, it has the inherent security feature of scrambling. On the software side, WLAN offers the encryption function (WEP) to enhance security and access control. What is WEP?

WEP is Wired Equivalent Privacy, a data privacy mechanism based on a 64-bit or 128-bit shared key algorithm, as described in the IEEE 802.11 standard. Appendix A: Troubleshooting Frequently Asked Questions 27 Wireless-G Portable USB Adapter Appendix B: Wireless Security Linksys wants to make wireless networking as safe and easy for you as possible. The current generation of Linksys products provide several network security features, but they require specific action on your part for implementation. So, keep the following in mind whenever you are setting up or using your wireless network. Security Precautions The following is a complete list of security precautions to take (at least steps 1 through 5 should be followed):

1. Change the default SSID. 2. Disable SSID Broadcast. 3. Change the default password for the Administrator account. 4. Enable MAC Address Filtering. 5. Change the SSID periodically. 6. Use the highest encryption algorithm possible. Use WPA if it is available. Please note that this may reduce your network performance. 7. Change the WEP encryption keys periodically. Security Threats Facing Wireless Networks Wireless networks are easy to find. Hackers know that in order to join a wireless network, wireless networking products first listen for beacon messages. These messages can be easily decrypted and contain much of the networks information, such as the networks SSID (Service Set Identifier). Here are the steps you can take:

Change the administrators password regularly. With every wireless networking device you use, keep in mind that network settings (SSID, WEP keys, etc.) are stored in its firmware. Your network administrator is the only person who can change network settings. If a hacker gets a hold of the administrators password, he, too, can change those settings. So, make it harder for a hacker to get that information. Change the administrators password regularly. SSID. There are several things to keep in mind about the SSID:

Note: Some of these security features are available only through the network router or access point. Refer to the router or access points documentation for more information. Appendix B: Wireless Security Security Precautions 28 Wireless-G Portable USB Adapter 1. Disable Broadcast 2. Make it unique 3. Change it often Most wireless networking devices will give you the option of broadcasting the SSID. While this option may be more convenient, it allows anyone to log into your wireless network. This includes hackers. So, dont broadcast the SSID. Wireless networking products come with a default SSID set by the factory. (The Linksys default SSID is linksys.) Hackers know these defaults and can check these against your network. Change your SSID to something unique and not something related to your company or the networking products you use. Change your SSID regularly so that any hackers who have gained access to your wireless network will have to start from the beginning in trying to break in. MAC Addresses. Enable MAC Address filtering. MAC Address filtering will allow you to provide access to only those wireless nodes with certain MAC Addresses. This makes it harder for a hacker to access your network with a random MAC Address. WEP Encryption. Wired Equivalent Privacy (WEP) is often looked upon as a cure-all for wireless security concerns. This is overstating WEPs ability. Again, this can only provide enough security to make a hackers job more difficult. There are several ways that WEP can be maximized:

1. Use the highest level of encryption possible 2. Use Shared Key authentication 3. Change your WEP key regularly WPA. Wi-Fi Protected Access (WPA) is the newest and best available standard in Wi-Fi security. Two modes are available: WPA-PSK and WPA-RADIUS. WPA-PSK gives you a choice of two encryption methods: TKIP (Temporal Key Integrity Protocol), which utilizes a stronger encryption method and incorporates Message Integrity Code

(MIC) to provide protection against hackers, and AES (Advanced Encryption Standard), which utilizes a symmetric 128-Bit block data encryption. WPA-RADIUS offers two encryption methods, TKIP and AES, with dynamic encryption keys, and it uses a RADIUS (Remote Authentication Dial-In User Service) server for authentication. WPA-PSK. If you do not have a RADIUS server, select the type of algorithm you want to use, TKIP or AES, and enter a password in the Passphrase field of 8-63 characters. Appendix B: Wireless Security Security Threats Facing Wireless Networks Important: Always remember that each device in your wireless network MUST use the same encryption method and encryption key or your wireless network will not function properly. 29 Wireless-G Portable USB Adapter WPA-RADIUS. WPA used in coordination with a RADIUS server. (This should only be used when a RADIUS server is connected to the Router or other device.) WPA-RADIUS offers two encryption methods, TKIP and AES, with dynamic encryption keys. Implementing encryption may have a negative impact on your networks performance, but if you are transmitting sensitive data over your network, encryption should be used. These security recommendations should help keep your mind at ease while you are enjoying the most flexible and convenient technology Linksys has to offer. Appendix B: Wireless Security Security Threats Facing Wireless Networks 30 Wireless-G Portable USB Adapter Appendix C: Windows Help All wireless products require Microsoft Windows. Windows is the most used operating system in the world and comes with many features that help make networking easier. These features can be accessed through Windows Help and are described in this appendix. TCP/IP Before a computer can communicate with the Access Point, TCP/IP must be enabled. TCP/IP is a set of instructions, or protocol, all PCs follow to communicate over a network. This is true for wireless networks as well. Your PCs will not be able to utilize wireless networking without having TCP/IP enabled. Windows Help provides complete instructions on enabling TCP/IP. Shared Resources If you wish to share printers, folder, or files over your network, Windows Help provides complete instructions on utilizing shared resources. Network Neighborhood/My Network Places Other PCs on your network will appear under Network Neighborhood or My Network Places (depending upon the version of Windows you're running). Windows Help provides complete instructions on adding PCs to your network. Appendix C: Windows Help 31 Wireless-G Portable USB Adapter Appendix D: Glossary 802.11b - An IEEE wireless networking standard that specifies a maximum data transfer rate of 11Mbps and an operating frequency of 2.4GHz. 802.11g - An IEEE wireless networking standard that specifies a maximum data transfer rate of 54Mbps, an operating frequency of 2.4GHz, and backward compatibility with 802.11b devices. Access Point - Device that allows wireless-equipped computers and other devices to communicate with a wired network. Also used to expand the range of a wireless network. Adapter - A device that adds network functionality to your PC. Ad-hoc - A group of wireless devices communicating directly with each other (peer-to-peer) without the use of an access point. Backbone - The part of a network that connects most of the systems and networks together, and handles the most data. Bandwidth - The transmission capacity of a given device or network. Bit - A binary digit. CSMA/CA (Carrier Sense Multiple Access/Collision Avoidance) - A method of data transfer that is used to prevent data loss in a network. CTS (Clear To Send) - A signal sent by a device to indicate that it is ready to receive data. Default Gateway - A device that forwards Internet traffic from your local area network. DHCP (Dynamic Host Configuration Protocol) - A protocol that lets one device on a local network, known as a DHCP server, assign temporary IP addresses to the other network devices, typically computers. DNS (Domain Name Server) - The IP address of your ISP's server, which translates the names of websites into IP addresses. DSSS (Direct-Sequence Spread-Spectrum) - A type of radio transmission technology that includes a redundant bit pattern to lessen the probability of data lost during transmission. Used in 802.11b networking. Encryption - Encoding data to prevent it from being read by unauthorized people. Appendix D: Glossary 32 Wireless-G Portable USB Adapter Ethernet - An IEEE standard network protocol that specifies how data is placed on and retrieved from a common transmission medium. Firmware - 1. In network devices, the programming that runs the device. 2. Programming loaded into read-only memory (ROM) or programmable read-only memory (PROM) that cannot be altered by end-users. Fragmentation - Breaking a packet into smaller units when transmitting over a network medium that cannot support the original size of the packet. Gateway - A system that interconnects networks. Hardware - The physical aspect of computers, telecommunications, and other information technology devices. IEEE (The Institute of Electrical and Electronics Engineers) - An independent institute that develops networking standards. Infrastructure Mode - Configuration in which a wireless network is bridged to a wired network via an access point. IP (Internet Protocol) - A protocol used to send data over a network. IP Address - The address used to identify a computer or device on a network. ISM band - Radio band used in wireless networking transmissions. ISP (Internet Service Provider) - A company that provides access to the Internet. LAN (Local Area Network) - The computers and networking products that make up the network in your home or office. MAC (Media Access Control) Address - The unique address that a manufacturer assigns to each networking device. Mbps (Megabits Per Second) - One million bits per second; a unit of measurement for data transmission. Network - A series of computers or devices connected for the purpose of data sharing, storage, and/or transmission between users. Node - A network junction or connection point, typically a computer or work station. Appendix D: Glossary 33 Wireless-G Portable USB Adapter OFDM (Orthogonal Frequency Division Multiplexing) - A type of modulation technology that separates the data stream into a number of lower-speed data streams, which are then transmitted in parallel. Used in 802.11a, 802.11g, and powerline networking. Packet - A unit of data sent over a network. Passphrase - Used much like a password, a passphrase simplifies the WEP encryption process by automatically generating the WEP encryption keys for Linksys products. Port - The connection point on a computer or networking device used for plugging in a cable or an adapter. Roaming - The ability to take a wireless device from one access point's range to another without losing the connection. Router - A networking device that connects multiple networks together, such as a local network and the Internet. RTS (Request To Send) - A packet sent when a computer has data to transmit. The computer will wait for a CTS

(Clear To Send) message before sending data. Server - Any computer whose function in a network is to provide user access to files, printing, communications, and other services. Software - Instructions for the computer. A series of instructions that performs a particular task is called a

"program". Spread Spectrum - Wideband radio frequency technique used for more reliable and secure data transmission. SSID (Service Set IDentifier) - Your wireless network's name. Subnet Mask - An address code that determines the size of the network. Switch - Device that is the central point of connection for computers and other devices in a network, so data can be shared at full transmission speeds. TCP/IP (Transmission Control Protocol/Internet Protocol) - A network protocol for transmitting data that requires acknowledgement from the recipient of data sent. WEP (Wired Equivalent Privacy) - A method of encrypting data transmitted on a wireless network for greater security. WLAN (Wireless Local Area Network) - A wireless network. Appendix D: Glossary 34 Wireless-G Portable USB Adapter Appendix E: Specifications Model Standards Cabling Type LEDs WUSB54GP ver.4 IEEE 802.11b, IEEE 802.11g, USB 1.1, and USB 2.0 USB extension base with integrated USB Cable Link (Blue- Blinking when 802.11g RF signal is active Frecuency Band 2.400~2.4835GHz (Subject to local regulation) Peak Gain of Antenna 2.4 GHz => 2dBi Transmit Power 16dBm (Typical)@11Mbps DSSS, 14 dBm (Typical)@54Mbps OFDM Receive Sensitivity 802.11g: 11Mbps @ -83dBm, 54Mbps @-67dBm Data Rate Channels OS Support 11,5.5,2, 1Mbs auto-selection on 802.11b 54,48,36,24,18,12,9,6 Mbps auto-selection on 802.11g 11 Channels (US and Canada), 14 Channels (Japan), 13 Channels (Europe) Windows 2000 and XP Security features WEP Encryption 64-bit and 128-bit Warranty 3 Year Appendix E: Specifications 35 Wireless-G Portable USB Adapter Dimensions W x H x D Unit Weight USB Base Certifications Operating Temp. Storage Temp. 1.25" x 4.50" x 0.38"

31.8 mm x 114.3 mm x 9.5 mm) 4.5 oz. (0.13 kg) 2.5 inches Diameter, approx. 6 foot cable FCC, CE 0C ~ 65C (32F ~ 150F)

-40C ~ 85C (-40F~ 185F) Operating Humidity 10% ~ 85% Non-Condensing Storage Humidity 5% ~ 90% Non-Condensing Appendix E: Specifications 36 Wireless-G Portable USB Adapter Appendix F: Warranty Information LIMITED WARRANTY Linksys warrants to the original end user purchaser ("You") that, for a period of [ ], (the "Warranty Period") Your Linksys product will be free of defects in materials and workmanship under normal use. Your exclusive remedy and Linksys's entire liability under this warranty will be for Linksys at its option to repair or replace the product or refund Your purchase price less any rebates. If the product proves defective during the Warranty Period call Linksys Technical Support in order to obtain a Return Authorization Number. BE SURE TO HAVE YOUR PROOF OF PURCHASE ON HAND WHEN CALLING. When returning a product, mark the Return Authorization Number clearly on the outside of the package and include a copy of your original proof of purchase. RETURN REQUESTS CANNOT BE PROCESSED WITHOUT PROOF OF PURCHASE. You are responsible for shipping defective products to Linksys. Linksys pays for UPS Ground shipping from Linksys back to You only. Customers located outside of the United States of America and Canada are responsible for all shipping and handling charges. ALL IMPLIED WARRANTIES AND CONDITIONS OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED TO THE DURATION OF THE WARRANTY PERIOD. ALL OTHER EXPRESS OR IMPLIED CONDITIONS, REPRESENTATIONS AND WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF NON-INFRINGEMENT, ARE DISCLAIMED. Some jurisdictions do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to You. This warranty gives You specific legal rights, and You may also have other rights which vary by jurisdiction. TO THE EXTENT NOT PROHIBITED BY LAW, IN NO EVENT WILL LINKSYS BE LIABLE FOR ANY LOST DATA, REVENUE OR PROFIT, OR FOR SPECIAL, INDIRECT, CONSEQUENTIAL, INCIDENTAL OR PUNITIVE DAMAGES, HOWEVER CAUSED REGARDLESS OF THE THEORY OF LIABILITY, ARISING OUT OF OR RELATED TO THE USE OF OR INABILITY TO USE THE PRODUCT, EVEN IF LINKSYS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. IN NO EVENT WILL LINKSYS' LIABILITY EXCEED THE AMOUNT PAID BY YOU FOR THE PRODUCT. The foregoing limitations will apply even if any warranty or remedy provided under this Section fails of its essential purpose. Some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to You. Please direct all inquiries to: Linksys, P.O. Box 18558, Irvine, CA 92623 USA. Appendix F: Warranty Information 37 Wireless-G Portable USB Adapter Appendix G: Regulatory Information FCC STATEMENT This (Series and Product name) has been tested and complies with the specifications for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used according to the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which is found by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna

Increase the separation between the equipment or device

Connect the equipment to an outlet other than the receivers

Consult a dealer or an experienced radio/TV technician for assistance FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditons:

(1) The device may not cause harmful interference, and (2) thise device must accept any interference received, including interference that may cause undesired operation. Canada (IC) :

To prevent radio interference to the licensed service, this device is intended to be operated indoors and away from windows to provide maximum shielding. Equipment (or its transmit antenna) that is installed outdoors is subject to licensing. Important: Cisco-Linksys, LLC declares that WUSB54GP ver.4 (FCC ID: Q87-WU54GPV4 is limited in CH1~CH11 for 2.4 GHz by specified firmware controlled in U.S.A. Important:

FCC Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This device complies with FCC RF Exposure limits set forth for an uncontrolled environments, under 47 CFR 2.1093 paragraph (d)(2). This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Appendix G: Regulatory Information 38 Wireless-G Portable USB Adapter Appendix H: Contact Information Need to contact Linksys?

Visit us online for information on the latest products and updates to your existing products at:

Can't find information about a product you want to buy on the web? Do you want to know more about networking with Linksys products? Give our advice line a call at:

Or fax your request in to:

If you experience problems with any Linksys product, you can call us at:

Don't wish to call? You can e-mail us at:

If any Linksys product proves defective during its warranty period, you can call the Linksys Return Merchandise Authorization department for obtaining a Return Authorization Number at:

(Details on Warranty and RMA issues can be found in the Warranty Information section in this Guide.) http://www.linksys.com or ftp.linksys.com 800-546-5797 (LINKSYS) 949-261-8868 800-326-7114 support@linksys.com 949-261-1288 Appendix H: Contact Information 39