FCC ID: 2AI4G-SM-ASM-7001 RGBCW Smart Path Light

R1-813-978-3900 Mon-Fri 9am-6pm (EST)INSTALLATION INSTRUCTIONSAMP LOW VOLTAGE LANDSCAPE LIGHTINGAMP Low Voltage Smart Path LightITEM: SM-ASM-7001!

IMPORTANT: PLEASE READ BEFORE INSTALLATION This fixture is intended for installation in accordance with local codes and the National Electric Code (NEC). Failure to adhere to these codes and instructions may result in serious injury, property damage and void the warranty. These instructions do not intend to cover all variations in installation, operation maintenance or mounting situations. 1. Make sure that the power is turned OFF before installing or servicing this fixture. 2. Warning: this fixture is not intended to be installed within 10 feet [3 meters] of a pool, spa or fountain. 3. This fixture is intended to be used only with a power supply

(transformer) rated maximum of 300 watts (25 AMPS) at 15 Volts. 4. Underground Low Energy Cable must not be buried over 6 (15.2 cm) in order to connect to the main low AMPage cable. 5. Fixture wires must be connected to smart platform transformer correctly. 6. Position the wire connector so that it is located within 6 inches (15.2 cm) from a building structure, a luminaire, or fitting. 7. The low AMPage cable should be protected by routing in close proximity to the luminaire or fitting, or next to a building structure such as a house or deck. 8. Contact only switch/plug when turning on. 9. When ordering additional wire or cable, please contact the manufacturer customer service or contact a qualified electrician.

IMPORTANT SAFETY INSTRUCTIONS LIGHTED LAMP IS HOT!

Lens/Guard WARNING TO REDUCE THE RISK OF FIRE OR INJURY TO PERSONS. 1. Turn off/unplug and allow to cool before reducing lamp. 2. Lamp gets HOT quickly!

3. Do not touch the hot lens, guard or cowl. 4. Keep lamp away from materials that may burn. 5. Do not touch lamp at any time. Use a soft cloth. Oil from skin may damage lamp. 6. Do not operate the fixture with a damaged or missing lens or shield. SAVE THESE INSTRUCTIONS 2 813.978.3900 [email protected] www.amplighting.com

WARNING NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. RF Exposure Statement: The distance between user and products should be no less than 20cm. 2 3 AMP Low Voltage Smart Path Light - SM-ASM-7001INSTALLATION INSTRUCTIONSR 813.978.3900 [email protected] www.amplighting.com 813.978.3900 [email protected] www.amplighting.com PACKAGE CONTENTS A. (1) Smart Path Light (Stem and LED Module) PARTS REQUIRED (SOLD SEPARATELY) A. (1) Hat B. (1) Mounting Accessories C. (1) AMP iQ Transformer

*** Visit our website www.amplighting.com to purchase. ***

PRODUCT DIMENSIONS The dimensions below are using the AMP MagnumPro hat. Please refer to the specification sheets online if you need dimensions for another hat. 9 1.54 2.68 5.97 22.67 4 813.978.3900 [email protected] www.amplighting.com 1 INSTALL STAKE Board Stake Ground Soil Determine the desired location for mounting the stake. Hammer the stake into the ground until flange of stake is flush to grade. To avoid damage to the stake, place a board on top of the stake while hammering. Note: If the ground is hard and the stake is difficult to install, make a crosscut in the ground using a flat shovel. 2 INSTALL SMART PATH LIGHT Pass supply wires through the center hole of the stake and thread the smart path light onto the stake. Clear away an area in the ground and lay the supply wires into the wireway slot. Supply Wires Smart Path Light Ground Stake Soil 4 5 AMP Low Voltage Smart Path Light - SM-ASM-7001INSTALLATION INSTRUCTIONSR 813.978.3900 [email protected] www.amplighting.com 813.978.3900 [email protected] www.amplighting.com 3 CONNECT SMART PATH LIGHT TO SMART TRANSFORMER AMP Smart Transformer Smart Path Light Fixture Wires For one smart path light, connect the fixture wires from the smart path light to the smart transformer directly.

*** The illustration shows one of AMP hubs. Other AMP hubs are also compatible for this system. AMP Smart Transformer Smart Path Light Hub (Sold Separately) Wires from Hub to Transformer Smart Path Light Feed Path Light Wires in Hub Smart Path Light For multiple smart path lights, we suggest using the hub to connect all the lights to the smart transformer. 1. Place the hub that is used to connect multiple smart path lights near the smart transformer. Use the proper length wires to connect the hub and the smart transformer. 2. Feed all the supply wires from the smart path lights into the hub. 6 813.978.3900 [email protected] www.amplighting.com 4 INSTALL HAT TO SMART PATH LIGHT Finial (Remove) Hat (Sold Separately) If applicable, remove the finial from the top of the smart path light first. Set aside the finial since it will not be used for this installation. Thread the hat onto the top of the smart path light. Smart Path Light HOW TO CONNECT SMART PATH LIGHT TO LIGHTING SYSTEM Before connecting the smart path light to your lighting system, please ensure that:

The APP AMP iQ has been installed on your smartphone. The smart transformer has been successfully on boarded, is powered on, and shows three solid LEDs on the front display. All products default to a factory setting. The lights must be paired to AMP iQ APP before using them. Whenever the smart path light is powered on, it will sequentially display five colors: red, green, blue, cool white, and warm white, with each color lasting for one second. After the color-cycling sequence:

1. When the smart path light has not yet been paired to the smart transformer, it will begin blinking alternately between warm white and cool white. 2. When the smart path light is paired to the smart transformer for the first time, the color temperature will turn to 2200K. 3. When the smart path light has been paired to the smart transformer already, it will be restored to the last working state. 6 7 AMP Low Voltage Smart Path Light - SM-ASM-7001INSTALLATION INSTRUCTIONSR 813.978.3900 [email protected] www.amplighting.com 813.978.3900 [email protected] www.amplighting.com HOW TO CONNECT SMART PATH LIGHT TO LIGHTING SYSTEM (CONTINUED) 1. Start the APP AMP iQ on your smartphone. Tap the + icon in the top right corner to add the smart path light to your lighting system. user Add Fixtures Tap the + icon in the top right corner to add fixtures to your lighting system. Home Fixtures Schedules 2. Click Add Fixture. Add Fixture Create Group Add Transformer Cancel Im Ready Cancel 3. Before click Im Ready, please check below notes on the screen:

Mobile Device: Keep your mobile device near the fixture for optimal connectivity during setup. Mesh Network Best Practice:

Begin by connecting fixtures nearest to the transformer first. As you add each fixture, a mesh network will form, extending connections to the furthest points. 8 813.978.3900 [email protected] www.amplighting.comuserAdd FixturesTap the + icon in the top right corner to add fixtures to your lighting system.HomeFixturesSchedulesAdd FixtureMobile DeviceKeep your mobile device near the fixture for optimalconnectivity during setup.Mesh Network Best PracticeBegin by connecting fixtures nearest to the transformerfirst. As you add each fixture, a mesh network will form,extending connections to the furthest points. HOW TO CONNECT SMART PATH LIGHT TO LIGHTING SYSTEM (CONTINUED) Select Transformer AC000W034891413 4. Select the transformer to which you would like to connect your smart path light. 5. Select the smart path light you would like to onboard. If the desired path light is not displayed, click the Re-

scan button until it becomes visible. Select Fixture Initially, not all light fixtures may be visible. However, the range of your mesh network will increase with each added fixture. Use identify to flash the light fixture. Fixture DDDD744D-BD60-1622-0000-000000000000 Fixture DDDD744D-BD64-AD20-0000-000000000000 Fixture DDDD744D-BD64-B0EA-0000-000000000000 Re-scan 8 9 AMP Low Voltage Smart Path Light - SM-ASM-7001INSTALLATION INSTRUCTIONSR 813.978.3900 [email protected] www.amplighting.com 813.978.3900 [email protected] www.amplighting.com HOW TO CONNECT SMART PATH LIGHT TO LIGHTING SYSTEM (CONTINUED) 6. Wait until the smart path light is connected to the Bluetooth Mesh. When the fixture successfully connects to the Bluetooth Mesh, it will change to a solid white color. Connecting Fixture to Mesh Continue Cancel Fixture Added Continue 7. Once the smart path light has been successfully onboarded to your lighting system, click Continue to operate the fixture and/or return to another menu. Congratulations! The installation and configuration of your AMP iQ Smart Path Light is complete. 10 813.978.3900 [email protected] www.amplighting.com TROUBLESHOOTING

*** An NFC-enabled smartphone is required for this step. ***

If you cannot control the smart path light by using the AMP iQ APP, refer to the following troubleshooting steps:

user Fixtures 1 Fixture FIX TUR ES FIXTURE 100%

1. Open the AMP iQ APP, find the fixture name that cannot be controlled. Click the fixture name to start the troubleshooting. 2. Click Fixture Details. Home Fixtures Schedules FIXTURE Brightness 100%

White Color Rename Fixture Fixture Details Cancel 10 11 AMP Low Voltage Smart Path Light - SM-ASM-7001INSTALLATION INSTRUCTIONSR 813.978.3900 [email protected] www.amplighting.com 813.978.3900 [email protected] www.amplighting.com TROUBLESHOOTING (CONTINUED) 3. Click Communication Reset. Fixture Details Fixture Type 11112222333344445555 Model 11112222333344445555 Firmware Version 1.0.5_RC2 Transformer EASYTRONIC 0 0 Groups Schedules History Communications Reset Remove Fixture Communication Reset 4. Click Reset Fixture Communications. Communication Reset NOTE: Near Field Communication (NFC) required. To proceed, your mobile devide must be within 1 inch of the fixture lens. The reset process may take 1-2 minutes. Reset Fixture Communications Factory Reset 5. Click Communication Reset. Communication Reset NOTE: Near Field Communication (NFC) required. To proceed, your mobile devide must be within 1 inch of the fixture lens. The reset process may take 1-2 minutes. Communications Reset 12 813.978.3900 [email protected] www.amplighting.com TROUBLESHOOTING (CONTINUED) Factory Reset 6. Now the screen shows Ready to Scan. Keep your smartphone on the current page and prepare to place your phone within 1 inch of the fixture lens. Communication Reset NOTE: Near Field Communication (NFC) required. To proceed, your mobile devide must be within 1 inch of the fixture lens. The reset process may take 1-2 minutes. READY TO SCAN Communications Reset Initiated. Cancel Smartphone 7. Put your smartphone within 1 inch of the fixture lens and wait for a few seconds. Lens Smart Path Light 12 13 AMP Low Voltage Smart Path Light - SM-ASM-7001INSTALLATION INSTRUCTIONSR 813.978.3900 [email protected] www.amplighting.com 813.978.3900 [email protected] www.amplighting.com TROUBLESHOOTING (CONTINUED) Factory Reset 8. Click Yes to start communication test. Communication Reset NOTE: Near Field Communication (NFC) required. To proceed, your mobile devide must be within 1 inch of the fixture lens. Communication Test This might take some time. The reset process may take 1-2 minutes. Please confirm if the device is blinking in red for few seconds and stays in red. Yes No 9. Now the smart path light is blinking red for few seconds and finally stays red. The progress bar displays the same color synchronously. This process might take some time. Factory Reset 10. Click Yes to continue. Communication Reset NOTE: Near Field Communication (NFC) required. To proceed, your mobile devide must be within 1 inch of the fixture lens. Communication Reset The reset process may take 1-2 minutes. Fixture communications have been reset. Yes The smart path light communication has now been reset and can once again be controlled via the AMP iQ app. If your smart path light still cannot be controlled after following these steps, you will have to perform a factory reset, described in the next section, and re-onboard the fixture. 14 813.978.3900 [email protected] www.amplighting.com HOW TO RESTORE THE DEFAULT SETTINGS To restore the smart path light to its factory default settings, perform the following steps:

1. Locate the wire termination point of the cable feeding the fixture. This is usually at a hub or the transformer. 2. With power on to the fixture, disconnect the fixtures wire termination for 1-2 seconds. 3. Reconnect the wire termination so that the fixture proceeds through its startup color sequence. 4. Repeat steps 2-3 for a total of five (5) off-on cycles. 5. On the fifth ON cycle, leave the fixtures wire termination intact. The fixture should now go through its red-green-blue-cool white-warm white sequence, then begin blinking alternately between warm white and cool white. IMPORTANT NOTE: Do not perform the five off-on sequence mentioned above on the transformer using the transformers power button or output power switch. Performing this sequence in this manner will force ALL fixtures powered by the transformer into a factory reset mode. Once the smart path light has been successfully onboarded to your lighting system, click Continue to operate the fixture and/or return to another menu. For any further questions, please contact AMP customer service. 14 15 AMP Low Voltage Smart Path Light - SM-ASM-7001INSTALLATION INSTRUCTIONSR 813.978.3900 [email protected] www.amplighting.com 813.978.3900 [email protected] www.amplighting.com RSpecifications and product details subject to change without notice. Copyright 2024, AMP Lighting, Lutz FL USA 33549 All rights reserved. [email protected] amplighting.com1-813-978-3700 Mon-Fri 9am-6pm (ET)

33 LANDSCAPE LUMINAIRE E466348-ET MODEL: SM-ASM-7001-25-B-BZ DATE: 202404 Made in China FOR OUTDOOR USE ONLY MAX 15VAC 0.75A 6W FCC ID : 2Al4G-SM-ASM-7001 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Led A See 1O 11 42 13 14.15 16 17 WW 20212 m.

DATE : 2024-11-25 Federal Communications Commission Authorization & Evaluation Division 7345 Oakland Mills Road Columbia, Maryland 21046 Authority to Act as Agent On our behalf, I appoint Jason Wu of Global United Technology Services Co., Ltd.and No. 123-128, Tower A, Jinyuan Business Building, No.2, Laodong Industrial Zone, Xixiang Road, Baoan District, Shenzhen, Guangdong, China to act as our agent in the preparation of this application for equipment certification. I certify that submitted documents properly describe the device or system for which equipment certification is sought. I also certify that each unit manufactured, imported or marketed, as defined in the Federal Communications Commissions regulations will have affixed to it a label identical to that submitted for approval with this application. For instances where our authorized agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for certification, still resides with LLW Enterprise LLC and 15486 N Nebraska Ave, Lutz, Florida 33549, United States Signature:

Name: Paul Kolenda Title: Director of Innovation & Product Development Company: LLW Enterprise LLC

LLW Enterprise LLC DATE : 2024-11-25 Equipment Autorisation Division Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 FCC ID: 2AI4G-SM-ASM-7001 Product Name: RGBCW Smart Path Light Request for Confidentiality To Whom It May Concern, Pursuant to the provisions of the Commissions rules Title 47 Sections 0.457 and 0.459, we are requesting the Commission to withhold the following attachment(s) as confidential documents from public disclosure indefinitely. These documents contain detailed system and equipment descriptions and are considered as proprietary information in operation of the equipment. The public disclosure of these documents might be harmful to our company and would give competitors an unfair advantage in the market. Schematic Diagram Block Diagram Operational Description In additional to above mentioned documents, in order to comply with the marketing regulations in Title 47 CFR 2.803 and the importation rules in Title 47 CFR 2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices, we request Short Term Confidentiality of the following attachment(s);

External Photos Test Setup Photos Internal Photos User Manual For 45 days, pursuant to Public Notice DA 04-1705. OR For 180 days pursuantto KDB 726920 D01. It is our understanding that all measurement test reports, FCC ID label format and correspondence during the certification review process cannot be granted as confidential documents and this information will be available for public review once the grant of equipment authorization is issued. Signature:

Name: Paul Kolenda Title: Director of Innovation & Product Development

LLW Enterprise LLC Covered Equipment Certification Attestation Letter 11/25/2024 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA ATTN.: Reviewing Engineer FCC ID: 2AI4G-SM-ASM-7001 LLW Enterprise LLC certifies that the equipment for which authorization is sought is not covered equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Note: If the equipment for which the applicant seeks authorization is produced by any of the entities identified on the current Covered List, the applicant should include an explanation on why the equipment is not covered equipment. LLW Enterprise LLC certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List (as a specifically named entity or any of its subsidiaries or affiliates)as an entity producing covered equipment. LLW Enterprise LLC certifies that the equipment for which authorization is sought does not include cybersecurity or anti-virus software produced or provided by Kaspersky Lab, Inc. or any of its successors and assignees, including equipment with integrated Kaspersky Lab, Inc. (or any of its successors and assignees) cybersecurity or anti-virus software pursuant to DA-24-886 and KDB 986446 D01 Covered Equipment Guidance section B(2a). Signed:

Printed name: Paul Kolenda Title: Director of Innovation & Product Development Company Name: LLW Enterprise LLC Date: 11/25/2024

Differences Declaration To whom concern, We company LLW Enterprise LLC hereby declares:

The product models SM-ASM-7001-25-B-BZ, SM-ZSM-7001-XX-Y-ZZ-R#, SM-ZSM-6001-XX-YZZ-R#, Z can be any alphanumeric character or blank for commercial purpose;XX can be any digit or blank for wire length (e.g. 8=8 feet or 25=25 feet); Y can be any alphanumeric character or blank for product material (e.g. B=

Brass, A= Aluminum or S= Steel); ZZ can be any alphanumeric character or blank for product colour (e.g. BZ=

Bronze, WH= White or BK= Black, RB=Raw brass, etc. );

-R# can be any alphanumeric character or blank for internal code. are identical in the same PCB layout, interior structure and electrical circuits, The differences are appearance color, power and model name for commercial purpose. Authorized signature:

Date: 2024-11-25

LLW Enterprise LLC U.S. Agent Designation for Service of Process -

Certification Attestation Letter Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA ATTN.: Reviewing Engineer FCC ID: 2AI4G-SM-ASM-7001 FRN of applicant: 0025728213 Per section 2.911(d)(7) of the FCC rules, LLW Enterprise LLC certifies that the equipment for which authorization is sought is designated to the following U.S. agent* for service of process:

Company Name: LLW Enterprise LLC FCC Registration Number (FRN): 0025728213 Physical U.S. Company Address: 15486 N Nebraska Ave, Lutz, Florida 33549, United States Contact Person: Paul Kolenda Agent Email Address: [email protected] The above contact person accepts the obligation for service of process. The applicant accepts to maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any Commission-related proceeding involving the equipment. Applicant Signed:

Agent Signed:

Signed:

Printed name: Paul Kolenda Title: Director of Innovation & Product Development Company Name: LLW Enterprise LLC Date: 11/25/2024 Signed:

Printed name: Paul Kolenda Title: Director of Innovation & Product Development Company Name: LLW Enterprise LLC Date: 11/25/2024 the applicant must designate a contact located in the United States for purposes of acting as the applicants agent for service of process, regardless of whether the applicant is a domestic or foreign entity. An applicant located in the United States may designate itself as the agent for service of process.