FCC ID: 2AZ2V-081822ZEN54 0-10V Dimmer

USER MANUAL 0-10 V DIMMER ZEN54 LR www.getzooz.com [email protected] FEATURES Z-Wave 0-10 V dimming control for LED xtures Great for 0-10 V LED drivers in LED panels Smooth dimming with instant status updates Installs behind your existing wall switch (on/o or momentary) 700 series Z-Wave chip for better range and faster control Z-Wave Long Range for ultra reliable no-mesh communication Advanced conguration including min and max brightness Built-in Z-Wave signal repeater for boosted communication SmartStart and S2 Security for a safer network SPECIFICATIONS Model Number: ZEN54 LR Power Input: 100-240 VAC, 50/60 Hz, max. 4.1 A, 984 W Power Output: 100-240 VAC, 50/60 Hz, max. 4 A, 960 W Maximum Load: 4 A (use with 0-10 V LED drivers only) Range: Up to 300 feet line of sight (or up to a mile with LR) Operating Temperature: 32-104 F (0-40 C) Installation and Use: Indoor only CAUTION This is an electrical device - please use caution when installing and operating the 0-10 V Dimmer. Remote control of appliances may result in unintentional or automated activation of power. Do not use this Z-Wave device to control electric heaters or other appliances which produce the risk of re, burns, or electrical shock when unattended. To reduce risk of overheating and possible damage to other equipment, do not install this unit to control a receptacle; a motor-operated appliance; a uorescent lighting xture; any device over 32 V DC power;

or a transformer-supplied xture. Use with 0-10 V LED drivers only. BEFORE YOU INSTALL This device is intended for installation in accordance with the National Electric Code and local regulations. It is recommen-

ded that a licensed electrician perform this installation. WIRING: READ IT!

1. CHECK THE LOAD: dont exceed 4 A for your 0-10 V Dimmer, USE ONLY WITH 0-10 V LED DRIVERS 2. POWER OFF: turn the circuit power o in the breaker panel before you start. If installing in a multi-switch box with multiple circuits, turn power o at all of the circuits. 3. CHECK THE WIRES: mark 0-10 V driver connections (GND-

and 0-10 V+), power (L and N), load to LED driver (LOAD) and switch connections (SW and GND). Dont rely exclusively on your multimeter to identify the wires!

NOT SURE WHAT YOURE SEEING? WELL HELP! SUPPORT.GETZOOZ.COM SEND US PICTURES OF YOUR SET-UP, BEFORE YOU DISCONNECT WIRES. 4. DISCONNECT THE SWITCH: remove the wires between the switch and the LED driver and label them accordingly. 5. CONNECT THE 0-10 V DIMMER: follow all installation steps carefully. Wire the device EXACTLY like in the diagram. Depending on your set-up, you may need to install the device at the LED fxture rather than in the switch box. ZEN54 WIRING DIAGRAM FOR 0-10 V LED DRIVERS 1 Connect the driver wires to GND - and 0-10V+ on ZEN54. 2 Connect the wall switch to the GND- bundle and the SW pigtail on the ZEN54. 3 Connect the LOAD on the ZEN54 to the line input on the LED driver. 4 Connect neutral from the 120 V power source to N on ZEN54 and the neutral input on the LED driver. 5 Connect line from the 120 V power source to the L pigtail on the ZEN54. 0-10 LED DRIVER GND 0-10V L N GND-

0-10V+

SW LOAD L N ZEN54 QUESTIONS?

[email protected] 120 V POWER COMPLETE INSTALLATION Secure your Z-Wave 0-10 V Dimmer and the wall switch in the box with mounting screws, handling the wires with care. Install the wall plate and restore power to the circuit. Z-WAVE CONTROL 1. ADD DEVICE to your hub Initiate inclusion (pairing) in the app (or web interface). Check Long Range if using. Not sure how? Scan one of the QR codes below for step-by-step instructions or get in touch: www.support.getzooz.com 2. Finalize inclusion at the dimmer. TAP THE Z-WAVE BUTTON 3 TIMES QUICKLY if using traditional Z-Wave inclusion. SCAN THE QR CODE / ENTER THE 5-DIGIT PIN if using the new SmartStart method.

V 0 1

0

D N G D A O L W S L N 0-10 V Dimmer ZEN54 LR FCC ID: 2AZ2V-081822ZEN54 Power: 100-240V~, 50/60Hz Max Load: A4 Freq: 908.42MHz Firmware: 1. 01 SmartStart PIN: XXXXX The SmartStart security PIN is located on the back of the relay, next to the Z-Wave Plus logo. The LED indicator will blink green to signal communication and turn green for 2 seconds if inclusion is successful or turn red for 2 seconds if the pairing attempt fails. 5021636 NEED SOME HELP? [email protected] Choose your hub and scan the QR code with your phones camera. Then click on the link to access the step-by-step pairing instructions. ON/OFF OR MOMENTARY SWITCHES ONLY Do not connect the ZEN54 to a wall dimmer, illuminated switch, or electronic add-on switch. The ZEN54 device can only be wired with on/o or momentary wall switches. Physical dimming available from momentary switches only. With on/o switches, dim via Z-Wave only. Z-Box Hub Hubitat Home Assistant SmartThings Get more tutorials and helpful tips at ww.support.getzooz.com Register your product for extended warranty and direct access to rmware les: getzooz.com/register PAGE 1 PAGE 2 INSTALLATION TIPS ADVANCED SETTINGS The 0-10 V Dimmer adds Z-Wave control to your existing 0-10 V LED driver. It cannot be connected to any other type of xture or appliance. In most cases, you will have power coming into the wall switch and a load connection between the switch and the LED driver. To accommodate the wiring requirements of the ZEN54 dimmer, you will need to use that connection to bring power to the ZEN54 installed at the xture. This will not leave enough wires to connect the ZEN54 dimmer to the wall switch directly. In that case, we would recommend installing any Z-Wave light switch to control the ZEN54 dimmer remotely via Z-Wave. The best Zooz models for this application are the ZEN72 Dimmer (for a classic switch look) or the ZEN32 Scene Controller which comes with programmable buttons you can link to your favorite brightness settings on the LED xture and trigger them with a single tap. Scan the QR code below to access a page with more wiring scenarios and diagrams. 3-WAY INSTALLATIONS You can install the 0-10 V dimmer in a 3-way set-up using simple on/o or momentary switches. Scan below to nd the right diagram for your scenario. SCAN FOR MORE WIRING DIAGRAMS TROUBLESHOOTING The device wont add to your system? Try this:

1. Initiate EXCLUSION and click the Z-Wave button 3 times quickly. 2. Click the Z-Wave button 4-5 times quickly to add. 3. Bring the gateway controller (hub) closer to the device, it may be out of range. 4. Get troubleshooting tips for your hub at www.support.getzooz.com EXCLUSION (REMOVING / UNPAIRING DEVICE) 1. Bring your Z-Wave hub close to the device if possible 2. Put the Z-Wave hub into exclusion mode (not sure how to do that? [email protected]) 3. Click the Z-Wave button on the device 3 times quickly

(the LED indicator will start blinking green) 4. Your hub will conrm exclusion, the LED indicator on the device will turn green for 2 seconds, and the ZEN54 will disappear from your controller's device list. FACTORY RESET If your primary controller is missing or inoperable, you may need to reset the device to factory settings. To reset the ZEN53, click the Z-Wave button once and immediately aer, press and hold it down for 15 seconds. The LED indicator will ash red during the process and turn solid red for 3 seconds to conrm successful reset. NOTE: All previously recorded activity and custom settings will be erased from the devices memory. WARNING This product should be installed indoors upon completion of any building renovations. Prior to installation, the device should be stored in a dry, dust-

and-mold-proof place. Do not install the device in a place with direct sun exposure, high temperature, or humidity. Keep away from chemicals, water, and dust. Ensure the device is never close to any heat source or open ame to prevent re. Ensure the device is connected to an electric power source that does not exceed the maximum load power. No part of the device may be replaced or repaired by the user. PAGE 3 Here is a selection of settings available to customize your device. Scan the QR code for a full list of parameters and look below for how to access them on your hub. Ramp rate to customize the fad-out and fade-in eect for on/o control Timer (automatic on/o scheduling) Minimum and maximum dim levels On/o status aer power failure SCAN SETTINGS Choose your hub and scan the QR code with your phones camera. Then click on the link to learn how to access and change the advanced settings for the device on your hub. Z-Box Hub Hubitat Home Assistant SmartThings ASSOCIATION This 0-10 V Dimmer supports Group 1 with up to 5 devices for Lifeline Group communication and Groups 2-4 with up to 5 devices. This device will send BASIC REPORT and SWITCH MULTILEVEL REPORT to Group 1, BASIC SET command to group 2, SWITCH MULTILEVEL SET to Group 3, and SWITCH MULTILEVEL START LEVEL CHANGE / SWITCH MULTILEVEL STOP LEVEL CHANGE to Group 4 when operated manually from the wall switch. You can set direct association to have the dimmer control another Z-Wave device independently of the hub by using Group 2. Not every hub exposes direct association settings in the interface so please go to www.support.getzooz.com to see if your system allows for direct association. S2 This product can be included and operated in any Z-Wave network with other Z-Wave certied devices from other manufacturers and/or other applications. All non-battery operated nodes within the network will act as repeaters regardless of vendor to increase reliability of the network. This product features the latest Security 2 (S2) framework to remove smart home network hacking risks. This device is equipped with a unique authentication code for trusted wireless communication. This is an ETL certied device. ETL, just like UL, is a Nationally Recognized Testing Laboratory. The ETL mark is proof of product compliance with North American safety standards. WARRANTY This product is covered under a 1-year limited warranty and extender 5-year warranty once registered. To read the full warranty policy or le a warranty claim, please go to www.getzooz.com/warranty IN NO EVENT SHALL ZOOZ OR ITS SUBSIDIARIES AND AFFILIATES BE LIABLE FOR ANY INDIRECT, INCIDENTAL, PUNITIVE, SPECIAL, OR CONSEQUENTIAL DAMAGES, OR DAMAGES FOR LOSS OF PROFITS, REVENUE, OR USE INCURRED BY CUSTOMER OR ANY THIRD PARTY, WHETHER IN AN ACTION IN CONTRACT, OR OTHERWISE EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DA-MAGES. ZOOZ'S LIABILITY AND CUSTOMER'S EXCLUSIVE REMEDY FOR ANY CAUSE OF ACTION ARISING IN CON-NECTION WITH THIS AGREEMENT OR THE SALE OR USE OF THE PRODUCTS, WHETHER BASED ON NEGLIGENCE, STRICT LIABILITY, BREACH OF WARRANTY, BREACH OF AGREEMENT, OR EQUITABLE PRINCIPLES, IS EXPRESSLY LIMITED TO, AT ZOOZ'S OPTION, REPLACEMENT OF, OR REPAYMENT OF THE PURCHASE PRICE FOR THAT PORTION OF PRODUCTS WITH RESPECT TO WHICH DA-MAGES ARE CLAIMED. ALL CLAIMS OF ANY KIND ARISING IN CONNECTION WITH THIS AGREEMENT OR THE SALE OR USE OF PRODUCTS SHALL BE DEEMED WAIVED UNLESS MADE IN WRITING WITHIN THIRTY (30) DAYS FROM ZOOZ'S DELIVERY, OR THE DATE FIXED FOR DELI-VERY IN THE EVENT OF NONDELIVERY. FCC NOTE THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE USERS AUTHORITY TO OPERATE THE EQUIPMENT. STORE INDOORS WHEN NOT IN USE. SUITABLE FOR DRY LOCATIONS ONLY. DO NOT IMMERSE IN WATER. NOT FOR USE WHERE DIRECTLY EXPOSED TO WATER. This device complies with Part 15 of the FCC Rules. Operation is subject to the following conditions:

1. This device may not cause harmful interference, 2. This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used according to instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in any given installation. If this equipment causes harmful interference to radio or television reception, the user may try to correct the interference by taking one or more of the following measures:

- Reorient or relocate receiving antenna

- Increase the separation between equipment and receiver

- Connect equipment into a separate outlet or circuit from receiver

- Consult the dealer or an experienced radio/TV technician for additional assistance All brand names displayed are trademarks of their respective holders. Zooz 2023 PAGE 4

www.support.getzooz.com

V 0 1

0

D N G D A O L W S L N 0-10 V Dimmer ZEN54 LR FCC ID: 2AZ2V-081822ZEN54 Power: 100-240V~, 50/60Hz Max Load: A4 Freq: 908.42MHz Firmware: 1.10 SmartStart PIN: XXXXX 5021636

C5266091_X24_Ed.1 Attestation Statements TO:

Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 The Commission adopted rules for covered telecommunications equipment and video surveillance equipment produced by entities identified on the Commissions Covered List1, which is periodically updated. See the Covered List for more details. This Attestation Statement is to confirm that we follow the Section 2.911(d)(5)(i)-(ii) that prohibit equipment authorization Applicant Company name: Lorenz High Definition LLC Grantee code: 2AZ2V FCC ID: 2AZ2V-081822ZEN54 Contact Name: Zbigniew Lorenz Address: 230 Rt 206 STE 401, Flanders, New Jersey 07836, United States Telephone No: +1 908.320.4204 Email: [email protected] i. ii. Lorenz High Definition LLC (the applicant) certifies that the equipment for which authorization is sought is not covered equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. The applicant must sign this certification. Lorenz High Definition LLC (the applicant) certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List as an entity producing covered equipment. The applicant must sign this certification. Date: 2023/02/10 Applicants Name: Zbigniew Lorenz Title: president Signature 1 The Commissions Covered List is published by the Public Safety and Homeland Security Bureau and posted on the Commissions website. This Covered List, which is periodically updated, identifies particular equipment, produced by particular entities, that constitutes covered equipment. https://www.fcc.gov/supplychain/coveredlist 1/1

Lorenz High Definition LLC Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 Subject: Request for Confidentiality FCC ID: 2AZ2V-081822ZEN54 To Whom It May Concern, C5266091_X10_Ed.1 Date: 2023/1/8 Pursuant to the provisions of Sections 0.457 and 0.459 of Commission's rules

(47CFR0.457, 0.459), we are requesting the Commission to withhold the following attachment(s) as confidential document from public disclosure. Exhibits ID Label/Location Attestation Statement External Photos Block Diagram Schematics Test Report Test Setup Photos Users Manual Internal Photos Parts List / Tune Up RF Exposure Info Operational Description Cover Letter(s) SDR Software / Security Info Long-Term Confidentiality No No No Short-Term Confidentiality No No No No No No No No In case of short-term Confidentiality, the applicant requests the exhibits selected above are withheld from public view for a period of _180_ days from the date of the Grant of Equipment Authorization and prior to marketing. Above mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. It is our understanding that all measurement test reports, FCC ID label format and correspondent during certification review process cannot be granted as confidential documents and those information will be available for public review once the grant of equipment authorization is issued. Sincerely, Signature:

Name: Zbigniew Lorenz 1/1 Title: president C5266091_X10_Ed.1 1/1

C5266091_X8_Ed.1 Letter of Authorization Lorenz High Definition LLC Company: Lorenz High Definition LLC Address: 230 Rt 206 STE 401, Flanders, New Jersey 07836, United States Product Name: 0-10V Dimmer Model Number: ZEN54 LR FCC Identifier: 2AZ2V-081822ZEN54 We authorize LGAI Technological Center S.A., Ronda de la Font del Carme, s/n, 08193 Bellaterra, Spain, to act on our behalf on all matters concerning the above named equipment. Any individual within LGAI Technological Center S.A. is authorized to act on our behalf and take action on the application. We declare that authorize LGAI Technological Center S.A., Ronda de la Font del Carme, s/n, 08193 Bellaterra, Spain, is allowed to forward all information related to the approval project to the Federal Communication Commission and to discuss any issues concerning the approval application. Any and all acts carried out by LGAI Technological Center S.A. on our behalf shall have the same effect as acts of our own. Name: Zbigniew Lorenz Date: 2022/1/8 Title: president Signature of applicant:

1/1

US Agent for Service of Process LETTER OF ATTESTATION TO:

Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 US Agent for Service of Process:

Company Name: Lorenz High Definition LLC FRN: 0030963904 Contact Name: Zbigniew Lorenz Address: 230 Rt 206 STE 401, Flanders, New Jersey 07836, United States Telephone No: +1 908.320.4204 Email: [email protected] This letter is to confirm that the US Agent for Service of Process accepts responsibility to act as a local representative on behalf of Lorenz High Definition LLC. The US Agent for Service of Process is aware of and agrees to comply with the requirements outlined in the FCC Equipment Authorization Program, Report and Order FCC 22-84, and clause 2.911. Applicant:

Company name: Lorenz High Definition LLC Product Description: 0-10V Dimmer Grantee code: 2AZ2V FCC ID: 2AZ2V-081822ZEN54 Contact Name: Zbigniew Lorenz Address: 230 Rt 206 STE 401, Flanders, New Jersey 07836, United States Telephone No: +1 908.320.4204 Email: [email protected] The Applicant is aware of and agrees to comply with the requirements outlined in the FCC Equipment Authorization Program, Report and Order FCC 22-84, and clause 2.911. This Agreement is valid until 12/31/2025 Date: 03/02/2023 Applicants Name: Zbigniew Lorenz Title: president Signature US Agent for Service of Processs Name:

Zbigniew Lorenz Title: president Signature 1/1