FCC ID: 2AZ2V-080822-ZEN53 DC Motor Controller

USER MANUAL DC MOTOR CONTROLLER ZEN53 LR www.getzooz.com ask@getzooz.com FEATURES Manual or Z-Wave control of DC motors (reversed polarity) Great for motorized shades, blinds, awnings, screens, and more Shutter and Venetian blind modes to choose from Installs behind your existing wall switch (momentary button) 700 series Z-Wave chip for better range and faster control Z-Wave Long Range for ultra reliable no-mesh communication Advanced conguration including timer settings and calibration Built-in Z-Wave signal repeater for boosted communication SmartStart and S2 Security for a safer network SPECIFICATIONS Model Number: ZEN53 LR Power: 6-32 VDC Maximum Load: 1.5 A (use with DC motors only) Range: Up to 300 feet line of sight (or up to a mile with LR) Operating Temperature: 32-104 F (0-40 C) Installation and Use: Indoor only CAUTION This is an electrical device - please use caution when installing and operating the motor controller. Remote control of appliances may result in unintentional or automated activation of power. Do not use this Z-Wave device to control electric heaters or other appliances which produce the risk of re, burns, or electrical shock when unattended. To reduce risk of overheating and possible damage to other equipment, do not install this unit to control a receptacle; a motor-operated appliance; a uorescent lighting xture; any device over 32 V DC power;

or a transformer-supplied xture. BEFORE YOU INSTALL This device is intended for installation in accordance with the National Electric Code and local regulations. It is recommen-

ded that a licensed electrician perform this installation. WIRING: READ IT!

1. CHECK THE LOAD: dont exceed 1.5 A for your DC motor, DO NOT CONNECT THIS DEVICE TO 120 VAC LOADS. 2. POWER OFF: turn the circuit power o in the breaker panel before you start. If installing in a multi-switch box with multiple circuits, turn power o at all of the circuits. 3. CHECK THE WIRES: mark motor connections (OUT), DC power (GND- and VDC+), and switch connections (S1 and S2). Dont rely exclusively on your multimeter to identify the wires!

NOT SURE WHAT YOURE SEEING? WELL HELP! SUPPORT.GETZOOZ.COM SEND US PICTURES OF YOUR SET-UP, BEFORE YOU DISCONNECT WIRES. 4. DISCONNECT THE SWITCH: remove the wires between the switch and the motor and label them accordingly. 5. CONNECT THE MOTOR CONTROLLER: follow all installation steps carefully. Wire the device EXACTLY like in the diagram. ZEN53 WIRING DIAGRAM FOR DC MOTORS 1 Connect the motor wires to OUT - and OUT + on ZEN53. 2 Keep your wall switch connected to the VDC positive +

on DC power. Connect S1 and S2 on the ZEN53 according to the instructions for your wall switch. The diagram below shows a single-pole double-throw center-o switch. 3 Connect the GND on the DC power source to the GND pigtail on ZEN53. 4 Connect the VDC positive + on the DC power source to the VDC+ pigtail on ZEN53. M QUESTIONS?

ask@getzooz.com ZEN53 S1 S2 OUT-

OUT+

GND-

VDC+

6-32 VDC POWER SOURCE Single-Pole Double Throw Center-O Switch COMPLETE INSTALLATION Secure your Z-Wave DC Motor Controller and the wall switch in the box with mounting screws, handling the wires with care. Install the wall plate and restore power to the circuit. Z-WAVE CONTROL 1. ADD DEVICE to your hub Initiate inclusion (pairing) in the app (or web interface). Check Long Range if using. Not sure how? Scan one of the QR codes below for step-by-step instructions or get in touch: www.support.getzooz.com 2. Finalize inclusion at the device. TAP THE Z-WAVE BUTTON 3 TIMES QUICKLY if using traditional Z-Wave inclusion. SCAN THE QR CODE / ENTER THE 5-DIGIT PIN if using the new SmartStart method. LR The SmartStart security PIN is located on the back of the relay, next to the Z-Wave Plus logo. The LED indicator will blink green to signal communication and turn green for 2 seconds if inclusion is successful or turn red for 2 seconds if the pairing attempt fails. NEED SOME HELP? ask@getzooz.com Choose your hub and scan the QR code with your phones camera. Then click on the link to access the step-by-step pairing instructions. BUTTON SWITCHES ONLY Do not connect the ZEN53 to a wall dimmer, illuminated switches, or electronic add-on switches. The ZEN53 device can only be wired with single pole button momentary switches!

Z-Box Hub Hubitat Home Assistant SmartThings Get more tutorials and helpful tips at ww.support.getzooz.com Register your product for extended warranty and direct access to rmware les: getzooz.com/register PAGE 1 PAGE 2 CALIBRATE THE DEVICE ADVANCED SETTINGS You will need to calibrate the ZEN53 DC Motor Controller to operate your shades or blinds correctly using Z-Wave control. The default duration for an operating cycle for this device is 60 seconds (for a full up-down cycle). You can calibrate the ZEN53 automatically or manually to set the right duration for up / down or open / close cycles. NOTE: If you are installing a brand new motor for your shades, please set it up according to the instructions rst. AUTOMATIC CALIBRATION Use this method for motors with limit switches. 1. Click the Z-Wave button 6 times quickly to enter calibration mode (or set parameter 5 to value 1 for shutter mode or value 2 for Venetian mode, add to hub rst). 2. The device will start calibrating while blinking green. The process takes around 10 seconds. 3. The motor will start opening the blinds until it reaches the limit and the blind is fully open. It will then reverse operation and start closing the blind until it reaches the closed limit. 4. The calibration process is now complete. The device has calculated the total time it needs to fully open or close your blinds or shutters. It will use this data to execute open and close commands. If you need to make any adjustments manually, you can enter the new values in parameters 3 and 4 in the advanced settings. SCAN FOR MANUAL CALIBRATION INSTRUCTIONS TROUBLESHOOTING The device wont add to your system? Try this:

1. Initiate EXCLUSION and click the Z-Wave button 3 times quickly. 2. Click the Z-Wave button 4-5 times quickly to add. 3. Bring the gateway controller (hub) closer to the device, it may be out of range. 4. Get troubleshooting tips for your hub at www.support.getzooz.com EXCLUSION (REMOVING / UNPAIRING DEVICE) 1. Bring your Z-Wave hub close to the device if possible 2. Put the Z-Wave hub into exclusion mode (not sure how to do that? ask@getzooz.com) 3. Click the Z-Wave button on the device 3 times quickly

(the LED indicator will start blinking green) 4. Your hub will conrm exclusion, the LED indicator on the device will turn green for 2 seconds, and the ZEN53 will disappear from your controller's device list. FACTORY RESET If your primary controller is missing or inoperable, you may need to reset the device to factory settings. To reset the ZEN53, click the Z-Wave button once and immediately aer, press and hold it down for 15 seconds. The LED indicator will ash red during the process and turn solid red for 3 seconds to conrm successful reset. NOTE: All previously recorded activity and custom settings will be erased from the devices memory. WARNING This product should be installed indoors upon completion of any building renovations. Prior to installation, the device should be stored in a dry, dust-

and-mold-proof place. Do not install the device in a place with direct sun exposure, high temperature, or humidity. Keep away from chemicals, water, and dust. Ensure the device is never close to any heat source or open ame to prevent re. Ensure the device is connected to an electric power source that does not exceed the maximum load power. No part of the device may be replaced or repaired by the user. PAGE 3 Here is a selection of settings available to customize your device. Scan the QR code for a full list of parameters and look below for how to access them on your hub. Motor mode to choose between shutter and Venetian operating mode Timer (automatic open/close) Full open and close cycle duration Open/close status aer power failure SCAN SETTINGS Choose your hub and scan the QR code with your phones camera. Then click on the link to learn how to access and change the advanced settings for the device on your hub. Z-Box Hub Hubitat Home Assistant SmartThings ASSOCIATION This Motor Controller supports Group 1 with up to 5 devices for Lifeline Group communication and Groups 2-4 with up to 5 devices. This device will send BASIC REPORT and SWITCH MULTILEVEL REPORT to Group 1, BASIC SET command to group 2, SWITCH MULTILEVEL SET to Group 3, and SWITCH MULTILEVEL START LEVEL CHANGE / SWITCH MULTILEVEL STOP LEVEL CHANGE when operated manually from the wall switch. You can set direct association to have the relay control another Z-

Wave device independently of the hub by using Group 2. Not every hub exposes direct association settings in the interface so please go to www.support.getzooz.com to see if your system allows for direct association. S2 This product can be included and operated in any Z-Wave network with other Z-Wave certied devices from other manufacturers and/or other applications. All non-battery operated nodes within the network will act as repeaters regardless of vendor to increase reliability of the network. This product features the latest Security 2 (S2) framework to remove smart home network hacking risks. This device is equipped with a unique authentication code for trusted wireless communication. WARRANTY This product is covered under a 1-year limited warranty and extender 5-year warranty once registered. To read the full warranty policy or le a warranty claim, please go to www.getzooz.com/warranty IN NO EVENT SHALL ZOOZ OR ITS SUBSIDIARIES AND AFFILIATES BE LIABLE FOR ANY INDIRECT, INCIDENTAL, PUNITIVE, SPECIAL, OR CONSEQUENTIAL DAMAGES, OR DAMAGES FOR LOSS OF PROFITS, REVENUE, OR USE INCURRED BY CUSTOMER OR ANY THIRD PARTY, WHETHER IN AN ACTION IN CONTRACT, OR OTHERWISE EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DA-MAGES. ZOOZ'S LIABILITY AND CUSTOMER'S EXCLUSIVE REMEDY FOR ANY CAUSE OF ACTION ARISING IN CON-NECTION WITH THIS AGREEMENT OR THE SALE OR USE OF THE PRODUCTS, WHETHER BASED ON NEGLIGENCE, STRICT LIABILITY, BREACH OF WARRANTY, BREACH OF AGREEMENT, OR EQUITABLE PRINCIPLES, IS EXPRESSLY LIMITED TO, AT ZOOZ'S OPTION, REPLACEMENT OF, OR REPAYMENT OF THE PURCHASE PRICE FOR THAT PORTION OF PRODUCTS WITH RESPECT TO WHICH DA-MAGES ARE CLAIMED. ALL CLAIMS OF ANY KIND ARISING IN CONNECTION WITH THIS AGREEMENT OR THE SALE OR USE OF PRODUCTS SHALL BE DEEMED WAIVED UNLESS MADE IN WRITING WITHIN THIRTY (30) DAYS FROM ZOOZ'S DELIVERY, OR THE DATE FIXED FOR DELI-VERY IN THE EVENT OF NONDELIVERY. FCC NOTE THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE USERS AUTHORITY TO OPERATE THE EQUIPMENT. STORE INDOORS WHEN NOT IN USE. SUITABLE FOR DRY LOCATIONS ONLY. DO NOT IMMERSE IN WATER. NOT FOR USE WHERE DIRECTLY EXPOSED TO WATER. This device complies with Part 15 of the FCC Rules. Operation is subject to the following conditions:

1. This device may not cause harmful interference, 2. This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used according to instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in any given installation. If this equipment causes harmful interference to radio or television reception, the user may try to correct the interference by taking one or more of the following measures:

- Reorient or relocate receiving antenna

- Increase the separation between equipment and receiver

- Connect equipment into a separate outlet or circuit from receiver

- Consult the dealer or an experienced radio/TV technician for additional assistance All brand names displayed are trademarks of their respective holders. Zooz 2022 PAGE 4

DC Motor Controller ZEN53 LR FCC ID: 2AZ2V-080822-ZEN53 Power: 6-32 VDC Max Load: 1.5 A Firmwar e: 1.10 SmartStart PIN: XXXXX www.support.getzooz.com

T U O

T U O

D N G

C D V 2 S 1 S

Lorenz High Definition LLC 230 Rt 206 STE 401, Flanders, New Jersey 07836, United States DATE : 2023-07-01 Lorenz High Definition LLC 230 Rt 206 STE 401, Flanders, New Jersey 07836, United States Attn: Director of Certification Authority to Act as Agent On our behalf, I appoint below company and person:

Name Position Company Name Dongguan Dongdian Testing Service Co.,Ltd. Address Damon Hu Manager Tel / Fax E-Mail 17, Zongbu Road 2, Songshan Lake Sci&Tech, Industry Park, Dongguan City, Guangdong Province, China, 523808 Tel: +86-0769-38826678-850 Damon_hu@dgddt.com to act as our agent in the preparation of this application for equipment certification. I certify that submitted documents properly describe the device or system for which equipment certification is sought. I also certify that each unit manufactured, imported or marketed, as defined in the Federal Communications Commissions regulations will have affixed to it a label identical to that submitted for approval with this application. Applicant name Lorenz High Definition LLC Address 230 Rt 206 STE 401, Flanders, New Jersey 07836, United States Yours sincerely, Signatory Lorenz , Agnes Name Position president Company Name Lorenz High Definition LLC Address Tel 230 Rt 206 STE 401, Flanders, New Jersey 07836, United States

+1 908.320.4204 E-Mail alorenz@thesmartesthouse.com

C5266091_X24_Ed.2 Attestation Statements TO:

Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 The Commission adopted rules for covered telecommunications equipment and video surveillance equipment produced by entities identified on the Commissions Covered List1, which is periodically updated. See the Covered List for more details. This Attestation Statement is to confirm that we follow the Section 2.911(d)(5)(i)-(ii) that prohibit equipment authorization Applicant Company name: Lorenz High Definition LLC Grantee code: 2AZ2V FCC ID: 2AZ2V-080822-ZEN53 Contact Name: Lorenz Agnes Address: 230 Rt 206 STE 401, Flanders, New Jersey 07836, United States Telephone No: +1 908.320.4204 Fax No: +1 908.320.4204 Email: alorenz@thesmartesthouse.com i. ii. Lorenz High Definition LLC (the applicant) certifies that the equipment for which authorization is sought is not covered equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. The applicant must sign this certification. Lorenz High Definition LLC (the applicant) certifies that, as of the date of the filing of the application, the applicant is not (as a specifically named entity or any of its subsidiaries or affiliates) identified on the Covered List as an entity producing covered equipment. The applicant must sign this certification.

[Insert applicant name] (the applicant) certifies that, as of the date of the filing of theapplication, the applicant [ is not] identified on the Covered List as an entity producing coveredequipment . Date: 202 3/7/26 Applicants Name: Lorenz, Agnes Title: president Signature:

1 The Commissions Covered List is published by the Public Safety and Homeland Security Bureau and posted on the Commissions website. This Covered List, which is periodically updated, identifies particular equipment, produced by particular entities, that constitutes covered equipment. https://www.fcc.gov/supplychain/coveredlist 1/1

Lorenz High Definition LLC Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 Subject: Request for Confidentiality FCC ID: 2AZ2V-080822-ZEN53 To Whom It May Concern, C5266091_X10_Ed.1 Date: 2023/07/01 Pursuant to the provisions of Sections 0.457 and 0.459 of Commission's rules

(47CFR0.457, 0.459), we are requesting the Commission to withhold the following attachment(s) as confidential document from public disclosure. Exhibits ID Label/Location Attestation Statement External Photos Block Diagram Schematics Test Report Test Setup Photos Users Manual Internal Photos Parts List / Tune Up RF Exposure Info Operational Description Cover Letter(s) SDR Software / Security Info Long-Term Confidentiality No No No Short-Term Confidentiality No No No No No No No No In case of short-term Confidentiality, the applicant requests the exhibits selected above are withheld from public view for a period of _180_ days from the date of the Grant of Equipment Authorization and prior to marketing. Above mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. It is our understanding that all measurement test reports, FCC ID label format and correspondent during certification review process cannot be granted as confidential documents and those information will be available for public review once the grant of equipment authorization is issued. Sincerely, Signature:

Name: Lorenz , Agnes Title: president 1/1

C5266091_X8_Ed.1 Letter of Authorization Lorenz High Definition LLC Company: Lorenz High Definition LLC Address: 230 Rt 206 STE 401, Flanders, New Jersey 07836, United States Product Name: DC Motor Controller Model Number: ZEN53 LR FCC Identifier: 2AZ2V-080822-ZEN53 We authorize LGAI Technological Center S.A., Ronda de la Font del Carme, s/n, 08193 Bellaterra, Spain, to act on our behalf on all matters concerning the above named equipment. Any individual within LGAI Technological Center S.A. is authorized to act on our behalf and take action on the application. We declare that authorize LGAI Technological Center S.A., Ronda de la Font del Carme, s/n, 08193 Bellaterra, Spain, is allowed to forward all information related to the approval project to the Federal Communication Commission and to discuss any issues concerning the approval application. Any and all acts carried out by LGAI Technological Center S.A. on our behalf shall have the same effect as acts of our own. Name: Lorenz , Agnes Date: 2023/07/01 Title: president Signature of applicant:

1/1

US Agent for Service of Process LETTER OF ATTESTATION TO:

Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 US Agent for Service of Process:

Company Name: Lorenz High Definition LLC FRN: 0030963904 Contact Name: Lorenz Agnes Address: 230 Rt 206 STE 401, Flanders, New Jersey 07836, United States Telephone No: +1 908.320.4204 Email: alorenz@thesmartesthouse.com Applicant:

Company name: Lorenz High Definition LLC Product Description: DC Motor Controller Grantee code: 2AZ2V FCC ID: 2AZ2V-080822-ZEN53 Contact Name: Lorenz Agnes Address: 230 Rt 206 STE 401, Flanders, New Jersey 07836, United States Telephone No: +1 908.320.4204 Email: alorenz@thesmartesthouse.com

[Lorenz, Agnes] certifies that, as of the date of this filing of the application with the TCB, [Lorenz High Definition LLC] is our designated US agent for service of process for the above referenced FCC ID. [Lorenz, Agnes] accepts to maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any commission related proceeding involving equipment. [Lorenz High Definition LLC] accepts, as of the date of the filing of the application, the obligation of the designated US agent for service of process for the above reference FCC ID. The US Agent for Service of Process is aware of and agrees to comply with the requirements outlined in the FCC Equipment Authorization Program, Report and Order FCC 22-84, and clause 2.911. The Applicant is aware of and agrees to comply with the requirements outlined in the FCC Equipment Authorization Program, Report and Order FCC 22-84, and clause 2.911. Date: 2023/7/26 Applicants Name: Lorenz, Agnes Title: president US Agents Name: Lorenz, Agnes Title: president Signature Signature 1/1 1/1