FCC ID: 2AZ2V-ZSE44 Temperature Humidity XS Sensor

USER MANUAL NEED SOME HELP?

[email protected] TEMPERATURE HUMIDITY XS SENSOR ZSE44 800LR Choose your hub and scan the QR code with your phones camera. Then click on the link to access the step-by-step pairing instructions. www.getzooz.com Firmware 2.0 S2 FEATURES Monitor temperature and humidity via Z-Wave NEW 800 series chip for faster communication and more battery life than ever Z-Wave Long Range for ultra reliable no-mesh communication Snap-in mounting bracket Powered by a single coin battery The latest S2 security and SmartStart for secure set-up Supports OTA rmware updates SPECIFICATIONS SE44 800LR Model Number: Z Power: 1 x CR2450 battery Operating Temperature: 5-104 F Dimensions: 2.2 x 1.3 x 0.2 Range: Up to 150 feet (up to 1300 with Long Range) line of sight Installation and Use: Indoor or outdoor under eve (cant be exposed to direct rainfall or sun, a little splash is OK) INSTALLATION 1. POWER THE SENSOR Use the triangle tool to gently open the sensors cover and access the battery. Pull the tab from under the battery to activate the sensor. Dont close the cover just yet. The LED indicator will start blinking for around 10 seconds once the sensor is powered. The LED indicator doesnt blink or light up at all?

Make sure the battery is inserted correctly per the positive / negative pole marks. Try a fresh lithium non-

rechargeable battery. Click the Z-Wave button 3 times as quickly as possible to force inclusion/exclusion mode in case you missed when it rst ashed. Z-WAVE BUTTON 3 x CLICK TO PAIR LED INDICATOR Z-WAVE CONTROL 1. ADD DEVICE to your hub Initiate inclusion (pairing) in the app (or web interface). Not sure how? [email protected] If youre using an S2 hub, it will ask you to enter the DSK PIN or scan the QR code printed on the inside of the sensors battery cover to complete SmartStart inclusion. 2. ACTIVATE the sensor While the hub is looking for new devices, click the Z-Wave button 3 times as quickly as possible. The LED indicator will start ashing to conrm inclusion mode and turn o once inclusion is completed. TIP!

Its best to add your sensor from the area where it will be installed so the hub can nd the best route to reach it right away. Z-Box Hub Hubitat Home Assistant SmartThings Get more tutorials and helpful tips at ww.support.getzooz.com TROUBLESHOOTING The sensor wont add to your system? Try this:

1. Initiate EXCLUSION in your hub and click the Z-Wave button 3 times as quickly as possible. 2. Click the Z-Wave button quicker when adding it. 3. Bring the sensor closer to your hub, it may be out of range. 4. Double-check if the device is powered. 5. Get troubleshooting tips specic to your hub at www.support.getzooz.com EXCLUSION (REMOVE DEVICE) 1. Bring the sensor within direct range of your Z-Wave hub. 2. Put the Z-Wave hub into exclusion mode (not sure how to do that? [email protected]). 3. Click the Z-Wave button 3 times as quickly as possible. 4. Your hub will conrm exclusion and the sensor will disappear from your controller's device list. FACTORY RESET When your networks primary controller is missing or otherwise inoperable, you may need to reset the device to factory settings manually. In order to complete the process, make sure the sensor is powered, then click the Z-Wave button twice and hold it the third time for 10 seconds. The LED indicator will blink continuously. Immediately aer, click the Z-

Wave button twice more to nalize the reset. The LED indicator will ash 3 times to conrm a successful reset. NOTE: All previously recorded activity and custom settings will be erased from the devices memory. WAKE-UP MODE The sensors wake-up interval is set to 12 hours by default to save battery life. Use the Wake Up Command Class to adjust the interval. Click the Z-Wave button 4 times quickly to wake the sensor up manually. The LED indicator will ash once to conrm the device is awake. During wake-up, the sensor turns the Z-Wave radio on for one minute to receive communication from the hub. Long wake-up interval will not aect how oen the sensor reports to your hub so we recommend leaving the default setting to conserve battery. ASSOCIATION The XS Sensor supports Group 1 for Lifeline communication and Groups 2-5 with up to 5 devices per group for basic on/o control. Use Group 2 for high temperature alerts; Group 3 for low temperature alerts; Group 4 for high humidity alerts; and Group 5 for low humidity alerts. See parameters 5-8 to set the thresholds. Please note that not all Z-Wave systems give users access to direct association settings so if youre note sure where to nd it, please get in touch with our support and well be happy to help. PAGE 1 PAGE 2 Scan to register your product for extended warranty and direct access to rmware les. BATTERY POWER TIP!

This sensor runs on a coin battery with smaller capacity than the lithium CR batteries used in other sensors so you may see the battery readings uctuate from low to higher readings when the sensor is awake during programming and testing. The battery will usually go back to its stable reading within a few hours so always allow a day or two aer you see the rst lower reading before checking on the actual battery life le for your device. S2 This product can be included and operated in any Z-Wave network with other Z-Wave certied devices from other manufacturers and/or other applications. All non-battery operated nodes within the network will act as repeaters regardless of vendor to increase reliability of the network. This product features the latest Security 2

(S2) framework to remove smart home network hacking risks. This device is equip-ped with a unique authentication code for trusted wireless communication. WARNING This product should be installed indoors or outdoors under eve upon completion of any building renovations. Prior to installation, the device should be stored in a dry, dust-and-mold-

proof place. Do not install the device in a place with direct sun exposure, high temperature, or humidity. Keep away from chemicals, water, and dust. Ensure the device is never close to any heat source or open ame to prevent re. No part of the device may be replaced or repaired by the user except for the batteries. WARRANTY This product is covered under a 12-

month limited warranty and 5-year extended warranty once registered. To read the full warranty policy, register your product, or le a warranty claim, please go to ww.getzooz.com/warranty FCC Statement This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help. The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction. ADVANCED SETTINGS Parameter 2: Decide when the sensor should report low battery to the hub. Values: 10-50 (% battery life). Default: 5 Size: 1 byte dec Parameter 3: Set the temperature reporting threshold. The sensor will send a new temperature report if the dierence compared to last reading exceeds the value set here. Values: 10 100 (degrees where 10 equals 1 degree); Default: 20. Size: 1 byte dec Parameter 4: Set the humidity reporting threshold. The sensor will report a new humidity value if the dierence compared to last reading exceeds the value set here. Values: 1 50 (%); Default: 10. Size: 1 byte dec Parameter 16: Set the temperature reporting interval. The sensor will report temperature at least that oen. Values: 0 disable this setting; 1 480 (minutes); Default: 240. Size: 2 byte dec Parameter 17: Set the humidity reporting interval. The sensor will report humidity at least that oen. Values: 0 disable this setting; 1 480 (minutes); Default: 240. Size: 2 byte dec Click the Z-Wave button 4 times quickly to wake the sensor up aer updating the settings. We listed the most helpful settings above. For a complete list of parameters, please go to www.support.getzooz.com or scan the QR code for a direct link to all of the settings. Not sure how to access advanced settings on your hub? Well help!

[email protected] MOUNTING INDOOR MOUNTING 1. We recommend including your sensor to the Z-Wave network from the location you want to install it before you actually mount it. 2. Place the sensor on a dry and clean surface in the space youd like to monitor temperature and humidity. Use the supplied adhesive tape to x the sensor to the surface, with the battery slot and sensor perforation pointing down. 3. Test the sensor overnight to make sure its reporting both temperature and humidity according to the settings. It may take up to 48 hours to adjust to the environment so give it a couple of days before evaluating the reports. OUTDOOR MOUNTING 1. Install the product outdoors under eve with the snap-on mounting bracket (included) for best results. 2. Add the sensor to Z-Wave from the area where it will be installed before mounting it. 3. Use the supplied screws to x the mounting bracket to a dry clean surface around the spot youd like to monitor. 4. Insert the sensor into the bracket, it should snap right on. Remember to position the device so that the sensor perforation is pointing down. SNAP-ON MOUNTING BRACKET All brand names displayed are trademarks of their respective holders. Zooz 2023 PAGE 3 PAGE 4

ZOOZ Temperature | Humidity XS Sensor Model: ZSE44 VER. 1.0 Battery: 1"CR2450 Frequency: 908.42MHz UPC: 853478006445 FCC ID: 2AZ2VZSE44 Firmware: 1.10 www.support.getzooz.com AB sta tis sive uP one] FE PLUS Made in China

ZOOZ Temperature Humidity XS Sensor Model: ZSE44 800LR Battery: 1*CR2450 Z-Wave Region: US/CA/MX UPC: 853478006445 FCC ID: 2AZ2V-ZSE44 Firmware: 2.0 www.support.getzooz.com t INSTALL THIS SIDE UP Meu C Made in China 59.5

C5266091_X10_Ed.2 Lorenz High Definition LLC Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 Subject: Request for Confidentiality FCC ID: 2AZ2VZSE44 To Whom It May Concern, Date: 2021-10-28 Pursuant to the provisions of Sections 0.457 and 0.459 of Commission's rules

(47CFR0.457, 0.459), we are requesting the Commission to withhold the following attachment(s) as confidential document from public disclosure. Exhibits ID Label/Location Attestation Statement External Photos Block Diagram Schematics Test Report Test Setup Photos Users Manual Internal Photos Parts List / Tune Up RF Exposure Info Operational Description Cover Letter(s) SDR Software / Security Info Long-Term Confidentiality No No No No No NOTE 1 NOTE 1 No No Short-Term Confidentiality NOTE 2 No No No No No No NOTE 1: Long-Term Confidentiality may be permitted under special conditions (See II. LONG-TERM CONFIDENTIALITY, Section 3 of KDB 726920, use last in force) NOTE 2: Short-Term Confidentiality can be requested for a maximum of 180 days from the date of the grant. Above mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. In case of above are withheld from public view for a period of Grant of Equipment Authorization and prior to marketing. short-term Confidentiality, the applicant requests the exhibits selected days from the date of the It is our understanding that all measurement test reports, FCC ID label format and correspondent during certification review process cannot be granted as confidential documents and those information will be available for public review once the grant of equipment authorization is issued. Sincerely, 1/1 C5266091_X10_Ed.2 Signature:

Name:Lorenz Agnes Title:

1/1

Lorenz High Definition LLC 230 Rt 206, STE 401, Flanders, NJ 07836, United States Federal Communications Commission Authorization and Evaluation Division Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 2023-11-27 To whom it may concer:

We, Lorenz

(FCC ID: 2AZ2V-ZSE44) is not covered equipment prohibited from receiving an equipment authorization pursuant to 2.903 of the FCC rules. igh Definition LLC, hereby certify that the equipment for which authorization is sought We also certify that, as of the date of the filing of the application, we are not identified on the Covered List (https://www foc. gov/supplychain/coveredlist) as an entity producing covered equipment. By signing this form, we confirm the above and that we are aware of the application requirements listed under 2.911(b) and (d)(5) and (6). The information provided in this letter is based on the referenced rule parts of Title 47 of the CFR as well as KDB 986446 DO1 Sincerely,

| wor ys Signature Lorenz Agnes Manager Lorenz High Definition LLC

CONFIDENTIALITY REQUEST for Certification Service in USA Federal Communication Commission Equipment Authorization Division, Application Processing Branch 7435 Oakland Mills Road Columbia, MD 21046 Date:<2023-11-27>

Pursuant to Paragraphs 0.457 and 0.459 of the Commission's Rules (47 C.F.R.) and Section 552(b)(4) of the Freedom of Information Act, we requests confidentiality for the following products:

FCC ID Model name 2AZ2V-ZSE44 ZSE44 For the product stated above, we request that the following information be held confidential;

Long-Term Exhibits Confidentiality Short-Term Confidentiality Short-Term Confidentiality Days Extemal Photos Internal Photos. Block Diagram Schematics Test Setup Photos:

User's Manual Parts List Tune Up moOooARRoo Operational Descriptions:

Dopooo0ol The long-term confidentiality exhibits contain our trade secrets and proprietary information that could be of benefit to our competitors. The short-term confidentiality on the basis of ensuring that business sensitive information remains confidential until the actual marketing of our new device. If you have any questions, please feel free to contact me at the address shown below. Sincerely, Lorenz Agnes/Manager Lorenz High Definition LLC 230 Rt 206, STE 401, Flanders, NJ 07836, United States

(848) 200-0995

[email protected]

Lorenz High Definition LLC 230 Rt 206, STE 401, Flanders, NJ 07836, United States Federal Communications Commission Authorization and Evaluation Division Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 2023-11-27 To whom it may concer:

We, the undersigned, hereby authorize Eurofins Product Service GmbH to act.on our behaffin all matters relating to applications for equipment authorization FCC ID: 2AZ2V-ZSE44 including the signing of all documents related to these matters. Any and all acts carried out by Eurofins Product Service GmbH on our behalf shall have the same effect as acts of our own. By signing this application form, we agree to Eurofins current valid General Terms and Conditions

(AGB),Testing and Certification Regulations (PZO) which can be viewed on following website www.eurofins de/ee or retrieved on request. We also hereby certify that no party to this application is subject to a denial of benefits, including FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. Sincerely,

| rere Aygo Name/Title: Lorenz Agnes/Manager Company: Lorenz High Definition LLC Address: 230 Rt 206, STE 401, Flanders, NJ 07836, United States Phone: (848) 200-0995 Fax: /

E-Mail: [email protected]

C5266091_X8_Ed.1 Letter of Authorization Lorenz High Definition LLC Company: Lorenz High Definition LLC Address: 230 Rt 206 STE 401 Product Name: temperature humidity Sensor Model Number: ZSE44 We authorize LGAI Technological Center S.A., Ronda de la Font del Carme, s/n, 08193 Bellaterra, Spain, to act on our behalf on all matters concerning the above named equipment. Any individual within LGAI Technological Center S.A. is authorized to act on our behalf and take action on the application. We declare that authorize LGAI Technological Center S.A., Ronda de la Font del Carme, s/n, 08193 Bellaterra, Spain, information related to the approval project to the Federal Communication Commission and to discuss any issues concerning the approval application. Any and all acts carried out by LGAI Technological Center S.A. on our behalf shall have the same effect as acts of our own. is allowed to forward all Name: Lorenz Agnes Date: 2021-10-28 Title:

Signature of applicant:

1/1

Lorenz High Definition LLC 230 Rt 206, STE 401, Flanders, NJ 07836, United States Federal Communications Commission Authorization and Evaluation Division Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 U.S. Agent Designation 2023-11-27 Lorenz High Definition LLC acknowledges their consent for the following contact located in the United States to act as their agent for service of process for the equipment for which authorization is sought (FCC ID: 2AZ2V-ZSE44):

Name and company of U.S. agent:

Lorenz High Definition LLC Physical U.S. address of agent:

230 Rt 206, STE 401, Flanders, NJ 07836 United States FRN of U.S. agent:

0030963904 Email address of U.S. agent:

[email protected] Lorenz High Definition LLC acknowledges their obligation to accept service of process on behalf of Lorenz High Definition LLC. Lorenz High Definition LLC with the FRN [0030963904] accepts its obligation to maintain an agent for service of process in the United States for no less than one year after either the grantee has permanently terminated all marketing and importation of the applicable equipment within the U.S., or the conclusion of any Commission-related administrative or judicial proceeding involving the equipment, whichever is later. By signing this form, we confirm the above and that we are aware of the application requirements listed under 2.911(d)(7). The information provided in this letter is based on the referenced rule parts of Title 47 of the CFR as well as KDB 986446 D01. An expiration date for this letter does not exist. In case the U.S. agent changes, the grantee is obligated to notify the FCC within 30 days via the granting TCB. Sincerely, Signature Lorenz Agnes Manager Signature Lorenz Agnes Manager Lorenz High Definition LLC Lorenz High Definition LLC 5 0 V

, U

) 7

) d

1 1 9

. 2 _ t n e g A _ S U

l e d o m

_ 8 4