FCC ID: UCZ-LW4211-C 1080P AHD/CVI Wireless Camera

1080p MPX Wireless Security Camera Quick Start Guide English Version 1.0 Resources Package Contents 1080p MPX Wireless Security Camera Wireless Receiver Antennas (2)*

* One each for camera and receiver. Power Adapters (2)*

Mounting Kits (2)*

Allen Key BNC Adapter ATTENTION:

A REGULATED UL / CSA APPROVED power supply is REQUIRED for use with this camera (included). Use of a non-regulated, non-conforming power supply can damage this product and voids the warranty. Need Help?

Visit us online for up-to-date software and complete instruction manuals Safety Precautions Read this guide carefully and keep it for future reference. Follow all instructions for safe use of the product and handle with care. Use the camera within given temperature, humidity and voltage levels noted in the cameras specications. Do not disassemble the camera. Do not point the camera directly towards the sun or a source of intense light. Use only the supplied regulated power supply provided with the product. Use of a non-regulated, non-conforming power supply can damage the product and void the warranty. Periodic cleaning may be required. Use a damp cloth only. Do not use any harsh, chemical-based cleaners. Installation Tips To ensure the best possible wireless performance, it is recommended to keep the following installation tips in mind when choosing a location for the camera:

Ensure your camera is placed as close to your receiver as possible. Reduce the number of obstructive materials between the camera and the receiver. Concrete, brick, metal and wood are the most common materials in your house that can cause poor signal strength. The camera uses the 2.4GHz band exclusively. Most new routers support both 2.4GHz and 5GHz bands. It is recommended to use other WiFi-connected devices using the 5GHz band when possible to ensure the 2.4GHz band is not overcrowded. Other electronic devices such as microwaves, TVs, cordless phones, and baby monitors can cause signal interference. It is recommended to install the camera as far away from these devices as possible. 1 2 3 4 Visit lorex.com Search for the model number of your product Click on your product in the search results Click on the Downloads tab Dimensions m m 8 3 1

/

4 5

. 2 8

/

7 0 m m

. 4 5

/

1 1 4 m m 6.1 / 155mm 4.4 / 113mm Disclaimers For a full list of compatible recorders, visit lorex.com/compatibility Not intended for submersion in water. This camera includes an Auto Mechanical IR Cut Filter. When the camera changes between Day/Night viewing modes, an audible clicking noise may be heard from the camera. This clicking is normal, and indicates that the camera lter is working. Point the camera where there is the least amount of obstructions (i.e., Install the camera where vandals cannot easily reach. This camera is rated for outdoor use. Installation in a sheltered location tree branches). is recommended. Copyright 2018 Lorex Corporation As our products are subject to continuous improvement, Lorex reserves the right to modify product design, specications and prices, without notice and without incurring any obligation. E&OE. All rights reserved. LW4211_QSG_EN_R1 LW4211 SERIES www.lorex.com LW4211_QSG_EN_R1.indd 1 10/10/2018 3:48:50 PM Installing the Camera IMPORTANT:

Test your camera prior to selecting a permanent mounting location by temporarily connecting the camera and cable to your DVR. Ensure the camera is no more than 700ft (213m) away from the wireless receiver in an open eld (with line of sight between antennas). The range is approximately 115ft (35m) or less in an indoor environment, depending if there are walls or obstructions between the camera and receiver. Review the Installation Tips section before choosing a mounting location for the camera. Before Installing the Camera Decide whether to run the cables through the wall / ceiling (drilling required) or along the wall / ceiling. If you run the cables along the wall / ceiling, you must run the cable through the cable notch on the base. This will keep the camera base ush to the surface when mounted. Cable Notch Setting Up the Receiver Connecting the receiver directly to DVR:

1. Ensure one of the included antennas is properly attached to the receiver. 2. Connect the receivers BNC cable to a compatible DVRs video input*. 3. Connect the receiver power adapter to the receiver. Connect the power adapter to a power outlet. NOTE: Make sure to rst connect and power on the camera before powering on the receiver. 4. (Optional) Use the included double-sided tape to securely attach the receiver to a at surface.

(OR) Secure the receiver to a at surface using the included mounting screws. Connecting the receiver to DVR using a BNC extension cable:

Female Power Male Power

**

To install your camera:

Mounting Surface Drywall Anchors (3) Receiver Installing Multiple Wireless Cameras When installing multiple digital wireless security cameras in the same environment, maintain at least 4 / 10cm between the receivers to optimize camera performance. NOTE: It is not recommended to install more than 3 digital wireless security cameras in the same environment to maintain optimal video frame rate performance. Audio Settings Audio recording without consent is illegal in certain jurisdictions. Lorex Corporation assumes no liability for use of its products that does not conform with local laws. ATTENTION:

Audio is disabled by default. You can enable audio through a compatible Lorex DVR. For a full list of compatible recorders, visit lorex.com/compatibility DVR To enable camera audio on LHV / DV Series DVRs:

1. In Live View, right-click and click Main Menu. Enter the system user name and password. Mounting Screws (3) Camera Base 1. Use the included mounting template or camera base to mark holes for the included mounting screws. Drill holes where marked. NOTE: Ensure one of the included antennas is properly attached to the camera. 2. Mount the camera to the mounting surface using the included mounting screws (3). NOTE: Use the included drywall anchors (3) if installing into drywall. 3. Adjust the angle of the camera until the desired view is set. Tighten the screws to secure the camera position. A. Use the included Allen key to loosen the adjustment screw on the camera base. Rotate the arm of the camera up to 360, then tighten the screw. B. Use the included Allen key to loosen the adjustment screw. Bend the arm of the camera up to 90, then tighten the screw. C. Use the included Allen key to loosen the adjustment screw furthest from the camera base. Rotate the camera until it is level with the viewing area, then tighten the screw. A B C 4. Connect the camera power adapter to the camera cable. Connect the power adapter to a power outlet. 5. Remove protective lm from the camera lens. LW4211_QSG_EN_R1 Connect the male power head to the female power head on the receiver. Connect the BNC connector to a video input on your DVR. Connect the female power head to the included receiver power adapter. Connect the BNC connector on the extension cable to the included BNC adapter. Connect the adapter to the BNC connector on the receiver. BNC Adapter

* This camera is only compatible with select DVRs. For a full list of compatible recorders, visit lorex.com/compatibility.

** Not included. Compatible BNC extension cable available at lorex.com. Pairing the Camera The camera and receiver have already been paired out of the box. If for some reason the pairing is lost, follow these steps to pair the camera and receiver. To pair the camera and receiver:

1. Make sure that the camera and receiver are both powered up and all antennas properly attached. Pair Button on the Receiver 2. Press the pair button on the receiver (see Figure 1). Figure 1 3. Press and hold the pair button on the back of the camera within 30 seconds of pressing the pair button on the receiver (see Figure 2). If successful, live video from the camera will appear on the monitor. Pair Button on the Camera Figure 2

) and select Recording > Recording. 2. Click (

3. Under Channel, select the channel where the audio-capable camera is connected. 4. Under Audio/Video, check the box on the left to enable audio recording. 5. Under Audio Format, select the format that will be used to record audio. G711a is recommended. 6. Click OK to save changes. 7. (Optional) Under Audio/Video, check the middle box to enable audio when viewing cameras through the computer or mobile applications. NOTE: These instructions are based on current DVR interface. For the most up-to-date instructions, see your DVRs instruction manual on lorex.com. LW4211_QSG_EN_R1.indd 2 10/10/2018 3:48:53 PM Caution:

The user is cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with Part 15 of the FCC Rules and Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (

2) this device must accept any interference received, including interference that may cause undesired operation. Le prsent appareil est conforme aux CNR dIndustrie Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes :

(1) lappareil ne doit pas produire de brouillage, et

(2) lutilisateur de lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-- Reorient or relocate the receiving antenna.

-- Increase the separation between the equipment and receiver.

-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-- Consult the dealer or an experienced radio/TV technician for help. FCC& IC Radiation Exposure Statement:

This equipment complies with FCC and Canada radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Dclaration dIC sur lexposition aux radiations:

Cet quipement est conforme aux limites dexposition aux radiations dfinies par le Canada pour des environnements non contrls. Cet quipement doit tre install et utilis une distance minimum de 20 cm entre lantenne et votre corps. Cet metteur ne doit pas tre install au mme endroit ni utilis avec une autre antenne ou un autre metteur. LW4211_QSG_EN_R1.indd 3 10/10/2018 3:48:53 PM

Lorex Technology Inc. Date: October 9, 2018 TO: Federal Communication Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MID 21046 Regarding: UCZ-LW4211-C To whom it may concern:

We, the undersigned, hereby authorize SGS-CSTC Standards Technical Services Co., Ltd. (SGS) Guangzhou branch and Kobe Jian in SGS-CSTC Standards Technical Services Co., Ltd. (SGS) Guangzhou branch to act on our behalf in all manners relating to application for equipment authorization with respect to the FCC ID above, including signing of all documents relating to these matters. Any and ail acts carried out by the agent on our behalf shall have the same effect as acts of our own. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). Where our agent signs the application for certification on our behalf, | acknowledge that all responsibility for complying with the terms and conditions for Certification, as specified by SGS North America, Inc., still resides with Lorex Technology Inc.. This authorization is valid until further written notice from the applicant. Name (Printea): Niles Kanapathipillai Title: Director, Quality Assurance Signature:

On behalf of Company: Lorex Technology Inc. LOREX Technology ine. 250 Royal Crest Court, Markham Ontario L3R 3$1 Canada Authorized Signature

Lorex Technology Inc. To: SGS North America Inc. 620 Old Peachtree Road SUITE 100 Suwanee, Georgia United States From: Lorex Technology Inc. 250 Royal Crest Court Markham, Ontario Canada L3R 3S$1 Regarding: Confidentiality Request regarding application for FCC ID UCZ-LW4211-C LONG TERM CONFIDENTIALITY Pursuant to 47 CFR Section 0.459 and 0.457 of the commission's rules, the applicant hereby request confidential treatment of the documents listed below, associated with the certification application referenced above. Schematic(s) Block Diagrams Operational Descriptions The documents above contain proprietary information not released to the public. Public disclosure of this information may prove harmful to the business of the applicant. Sincerely, Name (Printed): Niles Kanapathipillai Title: Director, Quality Assurance Signature: WZ2 a On behalf of Company: Lorex Technology Inc. LOREX Technology Inc. 280 Royal Creat Court, Markham Ontario LAR 3874 Canada Authorized Signature