FCC ID: UCZ-W452AS-Z 2K Outdoor Floodlight Camera

HD Video Floodlight Package Contents HD Video Floodlight Mounting Screws &

Anchors (3) A B Bracket Screws A and B (2) Safety Precautions Read this guide carefully and keep it for future reference. Follow all instructions for safe use and handling of the product. Periodic cleaning may be required. Use a damp cloth only. Do not use any harsh, Use the product within given temperature, humidity and voltage levels noted in the chemical-based cleaners. products specifications. Do not disassemble the floodlight. CAUTION Risk of fire. Do not install camera near flammable or combustible surfaces. Risk of electrical shock. Disconnect the power at the fuse box before installation. Disclaimers Always follow code standards when installing wired connections. This floodlight camera must be installed on a wall and a UL listed junction box. This floodlight includes an Auto Mechanical IR Cut Filter. When the camera changes between Day/Night viewing modes, an audible clicking noise may be heard from the floodlight. This clicking is normal, and indicates that the camera filter is working. Audio recording without consent is illegal in certain jurisdictions. Lorex Corporation assumes no liability for use of its products that does not conform with local laws. Mounting Bracket Wire Caps (3) Need Help?

Visit us online for up-to-date software and complete instruction manuals 1 2 3 4 Visit lorex.com Search for the model number of your product Click on your product in the search results Click on the Downloads tab W452AS Series Quick Start Guide lorex.com Scan for Lorex Home APP Hooks Phillips Machine Screw FCC Notice THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS:

(1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND

(2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. Copyright 2020 Lorex Corporation As our products are subject to continuous improvement, Lorex reserves the right to modify product design, specifications and prices, without notice and without incurring any obligation. E&OE. All rights reserved. Adjusting knobs Before assembly, there are important preparations to make. Recommendation:

Mount the floodlight camera 10 feet (3 meters) high with the motion detector levelled to the ground for optimizal detection of human-sized objects as far as 32 feet (10 meters). Product Overview Back Panel Front Panel Top cover Light sensor Speaker PIR motion sensor IR LED Microphone Camera Behavior Meaning LED Indicator Operating correctly. Ready for connection.

(steady)

(flashing)

(steady)

(flashing)

(flashing rapidly) Mobile device is attempting to connect to the camera. Device malfunction. Try resetting the camera and repeating the setup. Network connection failed. Try resetting the camera and repeating the setup.

(flashing rapidly) Memory slot error. Try removing and re-inserting the included memory slot card, or try a different card.

(alternating) Firmware upgrade in progress. V261LC_QSG_EN_R1.indd 1 V261LC_QSG_EN_R1.indd 1 11.4 290mm Memory slot*

Reset button**

7.3 / 185mm Floodlights STEP 1: Preparation To prepare for installation:

TURN OFF POWER TO YOUR FLOODLIGHT CIRCUIT AT THE FUSEBOX TO ENSURE NO POWER IS BEING SENT. If you are unsure of which breaker controls the circuit, then turn off the main power switch. If you do not know where your breaker is or how to turn off power, consult a licensed electrician. Verify that the supply voltage is correct. Connect fixture to a 100 VAC~240 VAC 50/60 Hz power source. DO NOT connect floodlight to a dimmer switch or timer. If you are not replacing a light fixture, you will need to run power cabling to the install location, and purchase a UL listed junction box for a licensed electrician to install. 12.8 / 325mm

* To access the memory slot and reset button, twist left to open the top cover.

** To reset the camera, hold down the reset button until the chime sounds and the LED Indicator turns red. 32 Feet Levelled to the ground 10 Feet V261LC_QSG_EN_R1 2020-03-03 5:40:22 PM 2020-03-03 5:40:22 PM STEP 2: Secure the Mounting Bracket Next, install the floodlights mounting bracket. 1. With the power shut off, remove the existing light fixture and bracket from the wall. 2. Disconnect the wires. To install directly to a junction box:

STEP 3: Connect the Wires To wire the floodlight:

1 Hang the floodlight camera from the mounting bracket using the supplied hooks. 2 The copper wire from the camera is ground wire. Connect the ground wire to the existing ground wire inside of your junction box. Use the supplied wire cap. In the case that you are not wiring from a junction box, twist your ground wire around the green screw on the bracket. 3 The white wire from the camera is neutral wire. Use a wire cap to connect the neutral wires from the camera and junction box. The black wire from your camera is a hot wire. Use a wire cap to connect the hot wires from the camera and junction box.*

STEP 4: Secure the Floodlight Next, install the floodlight camera. 1. Carefully push all the wires through the middle opening of the bracket into the junction box, and secure the floodlight camera through the middle hole using the Phillips machine screw. In the case that you are installing the floodlight camera directly to the bracket, fit the wires into the back openings of the camera. NOTE: Be sure to follow the Front / Up directions on the mounting bracket. To install directly on a wall:

3. 4. 3. 4. 5. 6. Run the wires through the middle of the supplied mounting bracket. Secure the mounting bracket to your junction box using one of the bracket screws, A or B depending on which size fits. Use the mounting bracket as a template to mark 3 holes in a triangular pattern. Use a 1/4 drill bit to drill in the marked holes. Gently tap the supplied mounting anchors into the drilled holes with a hammer. Align the bracket and use a Phillips head screwdriver to secure the supplied mounting screws into the mounted anchors. 1. 2. A B Hook one end into your floodlight camera. Hook the other end into the bracket. IMPORTANT: Properly ground fixture.

* Power wire colors in your home may be different. In such a case consult a licensed electrician. STEP 5: In-app Setup Next, connect the floodlight camera to the Lorex Home app. To link the floodlight:

Overview of Lorex Home app Live viewing screen:

Device name Lorex Floodlight Device settings To scan the QR code:

1. Download and install the free Lorex Home app from the App Store or Google Play Store. 2. Tap the Lorex Home icon to launch the app. Tap Sign up, then follow the on screen prompts to create an account. Record your account details below and store in a secure location:

Email:

Account Password:

3. Wait for the floodlight to start up. This may take up to 5 minutes after reconnecting power at the breaker. 1. Once the status LED on the floodlight is flashing green, tap Next in the Lorex Home app. The app will connect your mobile device to the floodlights hotspot. 2. Create a secure password for the floodlight. Record your floodlight password below and store in a secure location:

Floodlight Password:

Back to previous screen Play back recorded video Snapshot Siren Manual recording Light 2-way audio: tap to speak, tap again to disable 3. Select your Wi-Fi network from the list, then enter the Wi-Fi password to connect your floodlight to the Internet. NOTE: If the Wi-Fi connection is weak, try moving your router closer or adding a Wi-Fi extender. 4. Once the status LED on the floodlight is solid green, tap Next to add the floodlight to your Lorex Home account. 5. Set a name for the floodlight and configure date & time preferences, then tap Complete. Pause / Play Viewing modes Streaming quality*

Mute /

Unmute Fullscreen

* Change the streaming quality to SD (Standard Definition) to conserve bandwidth while watching live video. This will not impact the quality of recorded video. 4. Once the status LED on the floodlight is flashing green, tap + in the Lorex Home app. 5. Scan the QR code on the side of the floodlight camera using your mobile devices camera. NOTE: If your mobile device cannot scan the QR code, tap Manually enter Device ID. V261LC_QSG_EN_R1.indd 2 V261LC_QSG_EN_R1.indd 2 2. 3. Adjust the lens and light angle using the adjusting knobs. To enforce a water resistant seal, apply silicone compound around the entire perimeter where the junction box is attached to the bracket. 4. You may now restore power at the fusebox. NOTE: If the status LED on the floodlight camera does not turn on, check to make sure wiring is done correctly. FCC WARNING This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Caution: The user is cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. this device may not cause interference, and this device must accept any interference, including interference that may cause ISED WARNING This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:

(1)

(2) undesired operation of the device. Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radioexempts de licence. L'exploitation est autorise aux deux conditions suivantes :

(1)

(2) brouillage est susceptible d'en compromettre le fonctionnement. l'appareil ne doit pas produire de brouillage, et l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le This equipment complies with FCC/IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. ce matriel est conforme aux limites de dose d'exposition aux rayonnements, FCC / CNR-102 nonce dans un autre environnement.cette eqipment devrait tre install et exploit avec distance minimale de 20 entre le radiateur et votre corps. V261LC_QSG_EN_R1 2020-03-03 5:40:28 PM 2020-03-03 5:40:28 PM

Model No.: W452AS-Z Power Requirement: DC 12V/ 1A FE C Wireless Frequency: 2.4 GHz:5GHz FCC ID: UCZ-W452AS-Z 8 IC: 8575A-W452ASZ LOREX LOREX TECHNOLOGY INC en www.lorex.com Made in XXXXX

| | IIIT OU TT OR NT OT ADD MAC ID a WIFI MAC: XXXXXXXXXXXXX ADD SERIAL POT TO TT S/N: XXXXXXXXXXXXXAXXX Label locatione

Lorex Technology Inc. Date: 10/25/2021 Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 To whom it may concern:

I, the undersigned, hereby authorize UL Verification Services Inc. to act on our behalf in all manners relating to application for equipment authorization, including signing of all documents relating to these matters. Any and all acts carried out by UL Verification Services Inc. on our behalf shall have the same effect as acts of our own. I, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). In authorizing UL Verification Services Inc. as our representative, we still recognize that we are responsible to:

a) comply with the relevant provisions of the certification program;

b) c) d) e) make all necessary arrangements for the conduct of the evaluation, including provision for examining documentation and access to all areas, records (including internal audit reports) and personnel for the purposes of evaluation (e.g. testing, inspection, assessment, surveillance, reassessment) and resolution of complaints;

make claims regarding certification only in respect of the scope for which certification has been granted;

do not use our product certification in such a manner as to bring the Certification Division into disrepute and not make any statement regarding our product certification which the Certification Division may consider misleading or unauthorized;

upon suspension or cancellation of certification, discontinue use of all advertising matter that contains any reference thereto and return any certification documents as required by the Certification Division;

f) g) h) i) j) use certification only to indicate the products are certified as being in conformity with specified standards;

endeavor to ensure that no certificate or report nor any part thereof is used in a misleading manner;

ensure that any reference to our product certification in communication media such as documents, brochures or advertising, complies with the requirements of the Certification Division;

keep a record of all complaints made known to us relating to the products compliance with requirements of the relevant standard and to make these records available to the when requested;

take appropriate action with respect to such complaints and any deficiencies found in products or services that affect compliance with the requirements for certification;

k) document the actions taken. This authorization is valid until further written notice from the applicant. Sincerely Yours, Signed by:

Company Name: Lorex Technology Inc. Contact Name: Niles Kanapathipillai Title of PersonProject Manager Address: 250 Royal Crest Court, Markham, Ontario, L3R 3S1 Canada

Lorex Technology Inc. UCZ-W452AS-Z Request for Confidentiality Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 Subject:

FCC ID:

To Whom It May Concern:

Pursuant to the provisions of Sections 0.457 and 0.459 of the Commissions rules (47 CFR 0.457, 0.459), we are requesting the Commission to withhold the following attachments as confidential document from public disclosure indefinitely. Schematic Diagram Block Diagram Theory of Operation Above mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. It is our understanding that all measurement test reports, FCC ID label format and correspondent during certification review process cannot be granted as confidential documents and those information will be available for public review once the grant of equipment authorization is issued. Best Regards Company Name: Lorex Technology Inc. Contact Name: Niles Kanapathipillai Title of PersonProject Manager Address: 250 Royal Crest Court, Markham, Ontario, L3R 3S1 Canada Date:10/25/2021