FCC ID: UCZ-W441AA-Z 2K QHD Smart Indoor Wi-FI Security Camera

En 2K Wi-Fi Camera W441AA Series Quick Start Guide lorex.com W482CAD_QSG_TRILINGUAL_R1.indd 1 W482CAD_QSG_TRILINGUAL_R1.indd 1 2021-05-27 2:50:35 PM 2021-05-27 2:50:35 PM Thank you for your purchase!

How to get started with your 2K Wi-Fi Camera W482CAD_QSG_TRILINGUAL_R1.indd 2 W482CAD_QSG_TRILINGUAL_R1.indd 2 2021-05-27 2:50:35 PM 2021-05-27 2:50:35 PM Safety precautions Read this guide carefully and keep it for future reference. Follow all instructions for safe use and handling of the product. Operate the camera within the specified temperature, humidity and voltage and use manufacturer approved accessories. Do not disassemble the camera. Do not point the camera directly at the sun or a source of intense light. Periodic cleaning may be required. Use a damp cloth only. Do not use any harsh, chemical-based cleaners. Disclaimers A regulated UL / CSA approved power supply is required for use with this camera (included). Use of a non-regulated, non-conforming power supply can damage this product and voids the warranty. Not intended for submersion in water. Installation in a sheltered location recommended. Audio recording without consent is illegal in certain jurisdictions. Lorex Corporation assumes no liability for use of its products that does not conform with local laws. This camera includes an Auto Mechanical IR Cut Filter. When the camera changes between Day/Night view-

ing modes, an audible clicking noise may be heard from the camera. This clicking is normal, and indicates that the camera filter is working. Some channels on the 5GHz Wi-Fi band are restricted in Canada. This means certain Wi-Fi networks may not be available to connect to during setup. Audio recording without consent is illegal in certain jurisdictions. Lorex Corporation assumes no liability for use of its products that does not conform with local laws. W482CAD_QSG_TRILINGUAL_R1.indd 3 W482CAD_QSG_TRILINGUAL_R1.indd 3 2021-05-27 2:50:35 PM 2021-05-27 2:50:35 PM Contents Section Package Contents & Dimensions 1 2 3 4 5 6 7 8 9 Overview Status Indicator Camera Setup App Live View Camera Placement Optimize Motion Detection Wall Mounting Ceiling Mounting W482CAD_QSG_TRILINGUAL_R1.indd 4 W482CAD_QSG_TRILINGUAL_R1.indd 4 2021-05-27 2:50:35 PM 2021-05-27 2:50:35 PM 1 Package contents 2K Wi-Fi Camera

(x1) Power Adapter

(x1) 9.8 ft (3m) Weatherproof Extension Cable (x1) Wall Mounting Bracket (x1) Ceiling/Table Mounting Bracket

(x1) Pre-inserted Memory Card (x1) Mounting Template

(x1) Mounting Plate

(x1) Anchors (x8) Screws (x8) Wrench (x1) Cable Clips (x4) Note: The following contents is based on 1 camera Dimensions Camera with Wall Mount Height: 3.1 (78mm) Width: 3.1 (78mm) Length: 5.0 (128mm) Camera with Ceiling Mount Height: 4.2 (107mm) Width: 3.1 (78mm) Length: 5.2 (132mm) W482CAD_QSG_TRILINGUAL_R1.indd 5 W482CAD_QSG_TRILINGUAL_R1.indd 5 2021-05-27 2:50:43 PM 2021-05-27 2:50:43 PM 2 Overview FRONT SIDE BOTTOM 1 2 3 4 5 6 1. Microphone 2. Warning light 4. 9.2ft (2.8m) USB power cord 5. Threaded insert (for mounting) 7. MicroSD slot

(card included) 3. Status indicator 6. Speaker 8. Pairing / reset button 9. QR code 7 8 9 W482CAD_QSG_TRILINGUAL_R1.indd 6 W482CAD_QSG_TRILINGUAL_R1.indd 6 2021-05-27 2:50:46 PM 2021-05-27 2:50:46 PM 3 Status indicator

(solid)

(flashing)

(solid)

(flashing) Connected to network Ready to connect to network Factory reset Disconnected from network

(alternating) Firmware update in progress W482CAD_QSG_TRILINGUAL_R1.indd 7 W482CAD_QSG_TRILINGUAL_R1.indd 7 2021-05-27 2:50:46 PM 2021-05-27 2:50:46 PM 4 Camera setup 1. Connect power to the camera with the provided power adapter. When you hear the chime and the status indicator is flashing green, the device is ready for setup. Optional: Connect the weatherproof extension cable to the camera's cable. 2. Download the Lorex Home app by scanning the QR code. an account. 3. Open the Lorex Home app, and sign in or create 4. Tap + in the app, then follow the in-app instructions to complete the device setup. Ensure you update to the latest app and camera firmware version. W482CAD_QSG_TRILINGUAL_R1.indd 8 W482CAD_QSG_TRILINGUAL_R1.indd 8 2021-05-27 2:50:49 PM 2021-05-27 2:50:49 PM 5 App Live View Pause/play Viewing modes Play back recorded videos Camera settings Video quality SD/HD Fullscreen view Audio on/off W482CAD_QSG_TRILINGUAL_R1.indd 9 W482CAD_QSG_TRILINGUAL_R1.indd 9 2021-05-27 2:50:49 PM 2021-05-27 2:50:49 PM 6 Camera Placement Place the camera close to your Wi-Fi router as possible. Reduce the number of obstructive materials between the camera and the router or access point. Concrete, brick, metal and wood are the most common materials in your house that can cause poor signal strength. Other electronic devices such as microwaves, TVs, cordless phones, and baby monitors can cause signal interference. It is recommended to install the camera as far away from these devices as possible. W482CAD_QSG_TRILINGUAL_R1.indd 10 W482CAD_QSG_TRILINGUAL_R1.indd 10 2021-05-27 2:50:50 PM 2021-05-27 2:50:50 PM 7 Optimize Motion Detection Distance Optimal accuracy for objects within 5ft to 50ft (1.5~15m). Angle Angle the camera around 30-60 down from the level position. Height Install the camera between 8-16ft (2.5~5m) off of the ground. Levelled to the ground 8~16 ft 5~50 ft Note: Accuracy of person detection will be influenced by multiple factors, such as the persons distance from the camera, the height of the person, and the height and angle of the camera. Night vision will also impact the accuracy and distance of detection. W482CAD_QSG_TRILINGUAL_R1.indd 11 W482CAD_QSG_TRILINGUAL_R1.indd 11 2021-05-27 2:50:52 PM 2021-05-27 2:50:52 PM 8 Wall Mounting Camera Wall mounting bracket Screws Anchors

(Optional) Mounting surface Adjustable nut Mounting plate Mounting template To wall mount the camera:

1. 2. Place the mounting template onto the desired location. Note: Ensure an outlet is nearby, and keep in mind the cable lengths. Using a 15/64" (6mm) drill bit, drill 2 holes over the triangle symbols on the template. Optional: Drill 15/64 (6mm) holes for the anchors. W482CAD_QSG_TRILINGUAL_R1.indd 12 W482CAD_QSG_TRILINGUAL_R1.indd 12 2021-05-27 2:50:57 PM 2021-05-27 2:50:57 PM 3. 4. 5. Align the arrows of the mounting plate and template. Using a screwdriver and the provided screws, secure the mounting plate to the surface. Align the arrows between the wall mounting bracket and plate. Push the bracket in to install, then slide down to lock in place. You will hear a click when the bracket is installed. Attach the camera to the mounting bracket using the threaded insert at the rear of the camera. Rotate the camera clockwise until attached, then tighten into place with the adjustable nut. 6. Adjust the camera to the desired angle. Note: If the camera is not holding in place or difficult to adjust, unplug the camera and slide the bracket up to detach from the mounting plate. Tighten or loosen the 3 screws at the back of the mounting bracket to adjust accordingly. Repeat steps 4-6 to re-install. Adjustable screws Back - Wall mounting bracket W482CAD_QSG_TRILINGUAL_R1.indd 13 W482CAD_QSG_TRILINGUAL_R1.indd 13 2021-05-27 2:51:02 PM 2021-05-27 2:51:02 PM 9 Ceiling Mounting Mounting template Ceiling/table mounting bracket Camera Mounting surface Anchors

(Optional) Screws Adjustable ring Adjustable nut To ceiling mount the camera:

1. 2. Place the mounting template onto the desired location. Note: Ensure an outlet is nearby, and keep in mind the cable lengths. Using a 15/64" (6mm) drill bit, drill 4 holes over the X symbols on the template. Optional: Drill 15/64 (6mm) holes for the anchors. W482CAD_QSG_TRILINGUAL_R1.indd 14 W482CAD_QSG_TRILINGUAL_R1.indd 14 2021-05-27 2:51:03 PM 2021-05-27 2:51:03 PM 3. 4. 5. 6. Remove the 4 pre-inserted plugs from the ceiling/

table mounting bracket. Attach the camera to the ceiling/table mounting bracket using the threaded insert at the rear of the camera. Rotate the camera clockwise until attached, then use the wrench to tighten the adjustable nut in place. Place the bracket over the drilled holes. Using a screwdriver and the provided screws, secure the bracket to the surface. Rotate the adjustable ring counter-clockwise to loosen and adjust the camera to the desired position, then tighten to secure. Optional:

Feed the camera cable through the hole at the base of the bracket or the mounting surface. Open the cameras settings in the app and enable Image Rotation to flip the camera image. W482CAD_QSG_TRILINGUAL_R1.indd 15 W482CAD_QSG_TRILINGUAL_R1.indd 15 2021-05-27 2:51:05 PM 2021-05-27 2:51:05 PM Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that may cause undesired operation. This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:

(1) this device may not cause interference, and

(2) this device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radioexempts de licence. L'exploitation est autorise aux deux conditions suivantes :

(1) l'appareil ne doit pas produire de brouillage, et

(2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. This equipment complies with FCC/IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Need help?

Visit help.lorex.com for up-to-date information and resources:

Download product guides Watch how-to-videos Find related troubleshooting tips & FAQs Register your product Please see our full Terms of Service and Limited Hardware Warranty Policy visit, lorex.com/warranty. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Copyright 2021 Lorex Corporation As our products are subject to continuous improvement, Lorex reserves the right to modify product design, specifications and prices, without notice and without incurring any obligation. E&OE. All rights reserved. W482CAD_QSG_TRILINGUAL_R1 W482CAD_QSG_TRILINGUAL_R1.indd 16 W482CAD_QSG_TRILINGUAL_R1.indd 16 2021-05-27 2:51:05 PM 2021-05-27 2:51:05 PM

2K QHD Smart Indoor Wi-Fl Security Camera Model No.: W441AA-Z Power Requirement: 12V / 1.5A FE Wireless Frequency: 2.4GHz FCC ID: UCZ-W441AA-Z C IC: 8575A-W441AAZ LOREX TECHNOLOGY INC. LOREX www.lorex.com Manufactured in China THIS DEVICE COMPLIES WITH PART 15 OF THE FOC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS:

(1) THIS DEVICE MAY NOT CAUSE HARVIFUL INTERFERENCE, AND

(2)THIS DEVICEMUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.

SGS North America Inc. 620 Old Peachtree Road SUITE 100 Suwanee, Georgia 30024 United States Applicant Declaration Applicant Legal Business Name Lorex Technology Inc. 250 Royal crest Court, Markham, L3R 3S1, Ontario, Canada. UCZ UCZ-W441AA-Z Authorized Contact Name Niles Kanapathipillai Address Grantee Code FCC ID Contact Email Contact Phone Niles.Kanapathipillai@lorextechnology.com

(905) 946-8589 Ext: 125 I, the undersigned, certify that I am an authorized signatory for the Applicant and therefore declare;

in accordance with 47CFR2.911(d), all of the statements herein and the exhibits attached hereto are true and correct to the best of my knowledge and belief. in accepting a Grant of Equipment Authorization issued by a TCB, under the authority of the FCC, as a result of the representations made in this application, the Applicant is responsible for:

labeling the equipment with the exact FCC ID as specified in this application,

(1)

(2) compliance statement labeling pursuant to the applicable rules,

(3) compliance of the equipment with the applicable technical rules, if the Applicant is not the actual manufacturer of the equipment, appropriate arrangements have been made with the manufacturer to ensure that production units of this equipment will continue to comply with the FCCs technical requirements. in accordance with 47 CFR 2.909 and KDB394321, the Applicant has read, understood and agrees to accept that they are the responsible party and agree to abide by their responsibilities as specified under 47 CFR 2.909 and KDB394321. in accordance with ISO17065, FCC KDB641163, FCC KDB610077, KDB394321 and RSP-100, the Applicant has read, understood, accepts and agrees to abide by the post market surveillance requirements.

(1)

(2)

(3) the Applicant understands, accepts and agrees that a sample may be requested for surveillance testing. the Applicant shall make provisions to always have a production sample available upon request by SGS, FCC and/or ISED. the Applicant shall, upon request by SGS, at the Applicants expense, provide a production sample of the requested product to SGS, FCC and/or ISED as instructed. The sample shall include all support devices, cables, software, accessories or other hardware or software required for evaluation, review, certification and audit surveillance of products certified by SGS. neither the Applicant nor any party to the application is subject to a denial of Federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862 because of a conviction for possession or distribution of a controlled substance. See 47CFR 1.2002(b) for the definition of a party for these purposes. the Applicant has read, understood, accepts and agrees to abide by the SGS North America, Inc.(TCB) terms and conditions. Link to CFRs: https://www.fcc.gov/wireless/bureau-divisions/technologies-systems-and-innovation-division/rules-regulations-title-47 Link to KDBs: https://apps.fcc.gov/oetcf/kdb/index.cfm Link to RSP-100: https://www.ic.gc.ca/eic/site/smt-gst.nsf/eng/sf01130.html 1 Date:2021-11-04 Applicant Signature:

Print Name:

Title:

*NOTE: This declaration cannot be signed by an Agent, it shall be signed by an authorized person listed in the FCC database Niles Kanapathipillai Director of Quality Assurance a) b) c) d) e) f) g) Applicant Declaration Rev:0.0

Lorex Technology Inc. TO:

Federal Communication Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MID 21046 Date: 2021-11-04 Regarding: UCZ- W441AA-Z To whom it may concern:

We, the undersigned, hereby authorize Parlam Zhan to act on our behalf in all manners relating to application for equipment authorization with respect to the FCC ID above, including signing of all documents relating to these matters. Any and all acts carried out by the agent on our behalf shall have the same effect as acts of our own. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). Where our agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for Certification, as specified by SGS North America, Inc., still resides with Lorex Technology Inc. This authorization is valid until further written notice from the applicant. Name (Printed): Niles Kanapathipillai Title: Director of Quality Assurance Signature:

On behalf of Company: Lorex Technology Inc. Telephone: (905) 946-8589 Ext: 125

Confidentiality Request regarding application for FCC ID: UCZ-W441AA-Z SGS North America Inc. 620 Old Peachtree Road SUITE 100 Suwanee, Georgia United States Lorex Technology Inc. To:

From: Lorex Technology Inc. Regarding:

LONG TERM CONFIDENTIALITY Pursuant to 47 CFR Section 0.459 and 0.457 of the commissions rules, the applicant hereby request confidential treatment of the documents listed below, associated with the certification application referenced above. Schematic(s) Block Diagrams Operational Descriptions The documents above contain proprietary information not released to the public. Public disclosure of this information may prove harmful to the business of the applicant. Sincerely, Signature:

Printed Name (on file with the FCC associated with the Grantee Code): Niles Kanapathipillai Title: Director of Quality Assurance Company Name: Lorex Technology Inc.