DOC NOPreliminary 1.0 User Manual CUSTOMER PRODUCT 2.4GHz Wireless Digital Transceiver Module DRF-TR001( LW2110, LW2110PK2B) MODEL NO. DATE Nov. 2007 ELANsat Technologies Inc. 5F, No.12, Innovation Road , Science-Based Industrial Park, Hsin-chu, Taiwan, R.O.C. TEL+886-3-563-5105 FAX+886-3-563-5107 http//www.elansat.com E-mailsales@elansat.com 00RT-FRD Wireless Digital Transceiver 1( LW2110, LW2110PK2B) ELANsat Features Auto ACK & retransmit On the air max. data rate 2Mpbs Digital interface (SPI) speed 0~8 Mbps Software selectable channel form 2402MHz to 2478MHz (77 Selectable channels) Short switching time enable frequency hopping Power supply range: 3 V to 3.6 V Minimum number of external component Low power consumption: 3.3V, 30mA Transmission distance: 100 m (Line of sight) Outline: 23.2 x 20.8 x 4.3 mm 47 CFR Part 15 Subpart A Section 15.21 Applications Keyless Entry Wireless data communication Alarm and security systems Wireless home security, Video Door Bell, Video door phone Home automation Surveillance Wireless P-CAM, Video Baby Monitor Automotive Wireless Vision-Based Robotic System, Automotive Accessory Telemetry Intelligent sports equipment, Video Rockie-Talkie Industrial sensors Toys Camera Radio Controlled Toy Wireless Photo Frame Benefits Ready for production Reduce time to market Remove complicity of RF design No RF experience require No expensive RF equipment require Plug and play No fuse on turning and trimming No need for expensive external antenna 2007.12.06 Version: 1.0 Page of 7 1 www.elansat.com 00RT-FRD Wireless Digital Transceiver 1( LW2110, LW2110PK2B) ELANsat Specification Parameter Limits TYP MIN Power Section Supply Voltage Supply Current in Tx mode Supply Current in Rx mode Digital Input Section High level input voltage Low level input voltage Digital Output Section High level output voltage Low level output voltage RF Section Frequency Range Channel Bandwidth TX Power RX Sensitivity Operation 3 23 17 2.1 0 2.7 0 2400 1.8 12 3.3 30 18 MAX 3.6 33 19 2.25 1.08 3.6 0.3
2525 2 16 14
-81 Unit V mA mA Vpp Vpp Vpp Vpp MHz MHz dBm dBm Operating Temperature
-10
+60 2007.12.06 www.elansat.com Version: 1.0 Page of 7 2 00RT-FRD Wireless Digital Transceiver 1( LW2110, LW2110PK2B) ELANsat Pin Configuration and Mechanical Information 2007.12.06 www.elansat.com Version: 1.0 Page of 7 3 00RT-FRD Wireless Digital Transceiver 1( LW2110, LW2110PK2B) ELANsat Pin Description No. 1 2 3 4 5 6 7 8 9 10 Symbol Function VCC GND IRQ MISO MOSI SCK CSN CE X GND Power Supply Ground Maskable interrupt pin Master Input, Slave Output (output from slave) Master Output, Slave Input (output from master) Serial Clock (output from master) Chip Select Chip Enable Activates RX or TX mode Ground 2007.12.06 www.elansat.com Version: 1.0 Page of 7 4 00RT-FRD Wireless Digital Transceiver 1( LW2110, LW2110PK2B) ELANsat PCB layout guideline Any metal (including PCB track and holding screw) around the antenna will result in changing impedance and radiation pattern of the antenna. These two parameters are the most important for antenna performance. Reserve space around the antenna as much as possible. Connect all parts as close as possible to the pins of module and reduce the length of routing traces, to help on good audio performance, proper antenna pattern and EMC. When designing the receiver module in wireless speakers and headphones, the important design considerations are as follows:
1. Keep metal objects away from the antenna by 3 cm distance at least to avoid degradation on the antenna. For example, speaker unit, transformer, adaptor, wire, cable and other big metal object beside antenna will degrade the antenna performance. 2. Use regulated DC-power-supply to the modules, and separate the DC-power-supply of module with the other circuits. Antenna 1. Wire Antenna: A 27~31mm plastic-covered wire can be used as antenna. In principle, 31mm length is for a wire without any cover or very thin cover. The thicker of the cover, the shorter of the antenna length. Try various length for a certain wire to optimize the transmission distance. 2. Antenna Soldering:
standrd equipment The module is the only antenna that may be used TYPE:C1073-510001-A(SSR-80521) 2007.12.06 Version: 1.0 Page of 7 5 www.elansat.com 00RT-FRD Wireless Digital Transceiver 1( LW2110, LW2110PK2B) ELANsat Operation Block Diagram of DRF-TR001 The SPI data then is fed to SOIC for encoding, FSK-modulation, frequency conversion, and amplification. RF signal between SOIC and antenna is separated to two paths: transmission and receiving (by two RF switches). Transmitted RF Signal from SOIC is following by a power amplifier to increase output power and transmission distance. RF signal between SOIC and antenna is separated to two paths: transmission and receiving (by two RF switches). Transmitted RF Signal from SOIC is following by a power amplifier to increase output power and transmission distance. FCC Transmitter Notice:
This equipment has been certified and found to comply with the limits regulated by the FCC 47 CFR part15, subpart A Section 15.21. You are cautioned that changes or modifications not expressly approved by the part responsible for compliance could void the users authority to operate the equipment. 2007.12.06 Version: 1.0 Page of 7 6 www.elansat.com
(LW2110, LW2110PK2B) 15.247 82010 8 UCZM2110 8575A-LW2110 UCZM2110 8575A-LW2110 Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication. This radio transmitter (identify the device by certification number, or model number if Category II) has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.