FCC ID: 2ARRV-000376 Loxone Air Cpu-Modul

MANUAL Produkt:

Ersteller:

Loxone Air Cpu-Modul Urlhardt, Johannes Manual Loxone Air Cpu-Modul 1. Introduction 1.1. 1.2. Abbreviations and Acronyms Related Documents 2. Modul Overview 3. Specification 3.1. Electrical Characteristics 3.1.1. 3.1.2. 3.1.3. Absolute Maximum Ratings Power Supply RF Characteristics(1) 3.2. 3.3. Agency Certifications 4.1. 4.2. Revision History 4. 5. Physical/environmental Characteristics and Outline Soldering Profile United States (FCC) Innovation, Science and Economic Development Canada (ISED) Compliance statements Produkt:

Ersteller:

Loxone Air Cpu-Modul Urlhardt, Johannes MANUAL 1. Introduction 1.1. Abbreviations and Acronyms ADC API DC DTR Analog-to-Digital Converter Application Programming Interface Direct Current Data Terminal Ready EEPROM Electrically Erasable Programmable Read-Only Memory ESD GPIO HAF HVAC HW I2C IEEE IRQ ISM JTAG MAC MCU NRE OEM OTA PA Electrostatic Discharge General Purpose Input/output High Frequency Heating, Ventilating, and Air Conditioning Hardware Inter-Integrated Circuit Institute of Electrical and Electronics Engineers Interrupt Request Industrial, Scientific, and Medical radio band Digital interface for debugging of embedded device, also known as IEEE 1149.1 standard interface Medium Access Control layer Microcontroller Unit. In this document it also means the processor, which is the core of a ZigBit module Network layer Original Equipment Manufacturer Over-The-Air upgrade Power Amplifier Produkt:

Ersteller:

Loxone Air Cpu-Modul Urlhardt, Johannes MANUAL PCB PER RAM RF RPC Printed Circuit Board Package Error Ratio Random Access Memory Radio Frequency Reduced Power Consumption RTS/CTS Request to Send/ Clear to Send RX SMA SoC SPI SW TTM TX UART USART USB ZigBee, ZigBee PRO 802.15.4 Receiver Surface Mount Assembly System on Chip Serial Peripheral Interface Software Time-To-Market Transmitter Universal Asynchronous Receiver/Transmitter Universal Synchronous/Asynchronous Receiver/Transmitter Universal Serial Bus Wireless networking standards targeted at low-power applications The IEEE 802.15.4-2003 standard applicable to low-rate wireless Personal Area Network 1.2. Related Documents

[1] IEEE Std 802.15.4-2003 IEEE Standard for Information technology - Part 15.4 Wireless Medium Access Control

(MAC) and Physical Layer (PHY) Specifications for Low-Rate Wireless Personal Area Networks (LR-WPANs).

[2] AT86RF212B Datasheet in http://www.atmel.com/devices/AT86RF212B.aspx?tab=documents. MANUAL Produkt:

Ersteller:

Loxone Air Cpu-Modul Urlhardt, Johannes 2. Modul Overview The Loxone Air Cpu-Modul is a low power IEEE 802.15.4/6LoPAN module for Loxone Air Smart Home Products. Produkt:

Ersteller:

Loxone Air Cpu-Modul Urlhardt, Johannes MANUAL 3. Specification 3.1. Electrical Characteristics 3.1.1. Absolute Maximum Ratings Parameter Voltage on any pin, except RESET with respect to ground Input RF level Current into VCC pins Minimum

-0.3 V Maximum 3.6 V (VDD MAX)

+10dBm 200mA Notes:

1. Absolute Maximum Ratings are the values beyond which damage to the device may occur. Under no circumstances must the absolute maximum ratings given in this table be violated. Stresses beyond those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress rating only. Functional operation of the device at these or other conditions, beyond those indicated in the operational sections of this specification, is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. 2. Attention! The Loxone Air CPU Module is an ESD-sensitive device. Precaution should be taken when handling the device in order to prevent permanent damage. 3.1.2. Power Supply Parameter Supply voltage, VDD 3.1.3. RF Characteristics(1) Parameter Condition Frequency band FCC and Industry Canada(2) Numbers of channels (FCC and Industry Canada) Channel spacing (FCC and Industry Canada) Frequency band ETSI (European Union)(2) Number of channels (European Union) Range 1.8 to 3.6 Unit V Range 902 928 10 2 863 - 870 4 Unit MHz MHz MHz MANUAL Produkt:

Ersteller:

Loxone Air Cpu-Modul Urlhardt, Johannes Channel spacing (European Union) 1 Transmitter output power Adjusted in 36 steps

-25 to +11 Receiver sensitivity On-air data rate PER = 1%

-103 40 up to 250 Kbps MHz dBm dBm TX output/ RX input nominal impedance Note 1: For detailed characteristics, refer to [2]. For balanced 50 Note 2: Appropriate FW (Register selection) must be used for operating this Module in United States and Canada. Note 3: Range measured is Line of Sight and at 10ft elevation from Ground at different combinations of orientations of transmitter and receiver, with special conditions were there is minimal or no RF interference from other sources. 3.2. Physical/environmental Characteristics and Outline Parameters Size Value Comments 22.9 x 14.9 mm Operating temperature range

-40C to +85C

-40C to +85C operational MANUAL Produkt:

Ersteller:

Loxone Air Cpu-Modul Urlhardt, Johannes 3.3. Soldering Profile The J-STD-020C-compliant soldering profile is recommended according to the following table. Profile Feature Average ramp-up rate (217C to peak) Preheat temperature 175C 25C Temperature maintained above 217C Green Package 3C/s max. 180s max. 60s to 150s Time within 5C of actual peak temperature 20s to 40s Peak temperature range Ramp-down rate Time within 25C to peak temperature 260C 6C/s max 8 minutes MANUAL 4. Agency Certifications 4.1. United States (FCC) Produkt:

Ersteller:

Loxone Air Cpu-Modul Urlhardt, Johannes This equipment complies with Part 15 of the FCC rules and regulations. To fulfill FCC Certification requirements, an OEM manufacturer must comply with the following regulations:

1. Modules must be installed by original equipment manufacturers (OEM) only. 2. The module must only be operated with antennas adhering to the requirements defined in section Supported Antennas. 3. The Loxone Air Cpu-Modul modular transmitter must be labeled with its own FCC ID number, and, if the FCC ID is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following:

IMPORTANT: Contains FCC ID: 2ARRV-000376. This equipment complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation (FCC 15.19). Installers must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance. This device is approved as a portable device with respect to RF exposure compliance, and may only be marketed to OEM installers. IMPORTANT: Modifications not expressly approved by this company could void the user's authority to operate this equipment (FCC section 15.21). IMPORTANT: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense (FCC section 15.105). MANUAL Produkt:

Ersteller:

Loxone Air Cpu-Modul Urlhardt, Johannes 4.2. Innovation, Science and Economic Development Canada

(ISED) Compliance statements This device complies with ISED licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. This equipment complies with radio frequency exposure limits set forth by Industry Canada for an uncontrolled environment. Cet quipement est conforme aux limites d'exposition aux radiofrquences dfinies par Industrie Canada pour un environnement non contrl. CAUTION: Any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. The OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed (for example, digital device emissions, PC peripheral requirements, etc.). This Module is labelled with its own IC ID. If the IC ID Certification Number is not visible while installed inside another device, then the device should display the label on it referring the enclosed module. In that case, the final end product must be labelled in a visible area with the following:

Contains Transmitter Module IC: 24564-000376 OR Contains IC: 24564-000376 Ce module est tiquet avec son propre ID IC. Si le numro de certification IC ID n'est pas visible lorsqu'il est install l'intrieur d'un autre appareil, l'appareil doit afficher l'tiquette sur le module de rfrence ci-joint. Dans ce cas, le produit final doit tre tiquet dans un endroit visible par le texte suivant:

Contains Transmitter Module IC: 24564-000376 OR Contains IC: 24564-000376 4.3. Supported Antennas The FCC compliance testing of the Loxone Air Cpu-Modul has been carried out using the W5012 antenna from PulseLarsen Antennas. This antenna has an omnidirectional radiation pattern at an antenna gain of 2 dBi. In order to be allowed to use the module without re-certification, the product incorporating the Loxone MANUAL Produkt:

Ersteller:

Loxone Air Cpu-Modul Urlhardt, Johannes Air Cpu-Modul module must either use the antenna mentioned above or must use an antenna with an omnidirectional radiation pattern and a gain being less than or equal to 2 dBi. MANUAL 5. Revision History Produkt:

Ersteller:

Loxone Air Cpu-Modul Urlhardt, Johannes Doc. Rev. 1.0 Date 13/09/2018 Comments Initial document release

Product: Loxone Air Cpu-Modul IC #: 24564-000376 9,00 mm Data Matrix encoding EUI64

| . a WO CCo. DARD ANNATIE Company Logo 0x0 000376

eee Ov vw ae OM!

,00 mm

Technical Documentation Produkt:

Ersteller:

Loxone Air Cpu Modul Urlhardt, Johannes Block diagram Loxone Cpu Modul Internal Block diagram of AT86RF212B RF Transceiver IC, showing Internal Voltage Regulator AVREG, DVREG Technical Documentation Produkt:

Ersteller:

Loxone Air Cpu Modul Urlhardt, Johannes

LOXO N B No Gimmicks.

& Real Smart Homes Abs. Loxone Electronics GmbH Smart Home 1 4154 Kollerschiag Federal Communications Commission Authorization and Evaluation Division Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 Kollerschlag, 8. February 2019 Attention: Application Examiner RE: Request for Confidentiality Applicant: Loxone Electronics GmbH FCC ID: 2ARRV-000376 To Whom It May Concern:

Permanent Confidentiality Request is hereby submitted by Loxone Electronics GmbH to withhold permanently from public review certain portions of the application for equipment certification for the referenced FCC identifiers. This request for confidentiality is made pursuant to 47 CFR 0.457(d) and 0.459 of the FCC Rules. In particular, the following sections of the application are to be kept permanently confidential:

e Schematics e User Manual

(The product is for professional installation and the manual is very technical and is not provided to the consumer since the consumer cannot service the device.) Rationale for request for confidentiality:

Loxone Electronics GmbH has invested considerable time and materials in research and development to produce the referenced product. Disclosure of the permanently confidential portions of this application to competitors would not only give them significant competitive advantages in developing similar products, but would also disclose successful implementation of unpublished, leading edge technology developed by us. If you have questions or need further information, please contact Loxone Electronics GmbH.

/ if Sincerely/_ f Angireas Hetzendorfer Johannes Urlhardt cro Project Manager Loxone Electronics GmbH Loxone Electronics GmbH Loxone Electronics GmbH Bankverbindung Es gelten die AGB der Loxone Electronics GmbH sofern Smart Home 1 A~4154 Kollerschiag Raiffeisendank Kolierschiag nicht anders vereinbart wurde unter www loxone.com/agb T +43 7287 70700 BLZ 34231 Kontonummer 28407 Bis zur Bezahlung samtlicher Anspruche aus der F +43 7287 7070 999 IBAN AT973423100000028407 Geschftsverbindung behalt sich der Verkaufer das E: office@loxone.com BIC RZOOAT2L231 Eigentum an seinen Warenlieferungen vor

LOXONE webirtittone:

Abs : Loxone Electronics GmbH Smart Home 1 4154 Kollerschiag Federal Communications Commission 445 12th Street SW Washington, DC 20554 Kollerschlag, 8. February 2019 Subject:Limited Agency Agreement Loxone Electronics GmbH FCC ID: 2ARRV-000376 To Whom It May Concern:

We, Loxone Electronics GmbH, hereby authorized Intertek Testing Services to act as our Agent for the purpose of preparing application for FCC ID number 2ARRV-000376 under all applicable parts of the FCC rules and regulations. The effective date of this limited agency agreement is 8 February 2019. The Limited Agency Agreement expires on 1 July 2019 , unless sooner terminated or extended by written notice to Intertek Testing Services and the Federal Communications Commission. This is to advise that we are in full compliance with the Anti-Drug Abuse Act. The applicant is not subject to a denial of federal benefits pursuant to Section 5301 of the Anti-Drug Act of 1988, 21 U.S.C. 862, and no party to the application is subject to a denial of federal benefits pursuant to that section. If you have an estions or Comments, please do not hesitate to contact Loxone Electronics GmbH. IK lal HY

Andyeas Hetzendorfer Johannes Urlhardt CT, Project Manager Loxone Electronics GmbH Loxone Electronics GmbH Loxone Electronics GmbH Bankverbindung, Es gelten die AGB der Loxone Electronics GmbH sofern Smart Home 1 - A-4154 Kolierschiag Raiffeisenbank Kolierschlag nicht anders vereinbart wurde unter www.loxone.com/agb T. +43 7287 70700 BLZ 34231 - Kontonummer 28407, Bis zur Bezahlung samtlicher Anspriche aus der F +43 7287 7070 999 IBAN AT973423100000028407 Geschafisverbindung benalt sich der Verkaufer das E. office@loxone.com BIC RZOOAT2L231 Eigentum an seinen Warentieferungen vor

LOXONE w2Etistomes Abs.: Loxone Electronics GmbH Smart Home 1 - 4154 Kollerschlag Federal Communications Commission Authorization and Evaluation Division Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 Kollerschlag, 8. February 2019 RE FCC ID: 2ARRV-000376 To the certification reviewer:

We are hereby applying for limited modular approval of the above-referenced FCC ID, based on compliance with all of the criteria as detailed below. Sincerely, ie Urlhardt Project Manager Part 15 Unlicensed Single Modular Transmitter Approval Justification per 15.212 reference Comply (Y/N Y Requirement per 15.212 The radio elements of the modular transmitter must have their own RF shielding. Shielding is provided by a metal cover over the circuitry. All modulation and data inputs are buffered by circuitry on the transmitter chip. Power supply regulation is provided by Y circuitry on the transmitter chip. The modular transmitter must have buffered modulation/data inputs (if such inputs are provided. The modular transmitter must have its own power supply regulation. The modular transmitter must comply with the antenna and transmission system requirements of 15.203, 15.204(b) and 15.204(c). The application is intended for professional Y installation only. The supported antenna types are listed in the modules users manual. The modular transmitter must be tested in a stand-alone configuration, i.e., the module must not be inside another device during testing for compliance with Part 15 rameters. The modular transmitter must be equipped with either a permanently affixed label or must be capable of electronically displaying its FCC identification number. If the FCC ID photos. Testing was performed with the module extended outside of the host on a special extender board, as shown in the test setup Y A drawing of the host label is provided as an exhibit. Loxone Electronics GmbH Bankverbindung: Es gelten die AGB der Loxone Electronics GmbH sofern Smart Home 1 - A-4154 Kollerschlag Raiffeisenbank Kollerschlag nicht anders vereinbart wurde unter www.loxone.com/agb T. +43 7287 70700 BLZ 34231 Kontonummer 28407 Bis zur Bezahlung samtlicher Anspriiche aus der F: +43 7287 7070 999 IBAN AT973423100000028407 Geschaftsverbindung behait sich der Verkaufer das E: office@loxone.com BIC RZOOAT2L231 Eigentum an seinen Warenlieferungen vor. LOXONE 22i22ttomes is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module.

(vii)

(viii) Refer to the Loxone Air Cpu-Modul User Y Manual The modular transmitter must comply with any specific rules or operating requirements that ordinarily apply to a complete transmitter and the manufacturer must provide adequate instructions along with the module to explain any such requirements. A copy of these instructions must be included in the application for equipment authorization. The modular transmitter must comply with | Refert to SAR Exclusion Caclulation any applicable RF exposure requirements in its final configuration. Loxone Electronics GmbH Bankverbindung: Es gelten die AGB der Loxone Electronics GmbH sofern Smart Home 1 - A-4154 Kollerschlag Raiffeisenbank Kollerschlag nicht anders vereinbart wurde unter www. loxone.com/agb T. +43 7287 70700 BLZ 34231 - Kontonummer 28407 Bis zur Bezahlung samtlicher Anspriiche aus der F: +43 7287 7070 999 IBAN AT973423100000028407 Geschaftsverbindung behait sich der Verkaufer das E: office@loxone.com BIC RZOOAT2L231 Eigentum an seinen Warenlieferungen vor.

Theory of Operation/Technical Description FCC ID: 2ARRV-000376 RF circuit function:

The IEEE 802.15.4 compliant AT86RF212B transceiver generates a modulated carrier wave at 906- 924 MHz with 10 IEEE 802.15.4 channels. This transceiver circuit is used by system applications as a physical layer for 6LowPAN Smart Home applications. RF signal flow:

The Transceiver IC outputs a differential RF signal (RFP & RFN) which is converted to single ended by the balun and then passes through the RF path via pads to the antenna on the carrier board and gets radiated or vice versa during reception. Description of Antenna system:

RF signal from/to the front end goes via pads to carrier board which connects the antenna. Only antennas with a radiation pattern and a gain being less than or equal to antennas listed in the manual are allowed for operation. Compliance with 15.203 antenna requirements:

FCC 15.203 requirements for this design are tested and verified during FCC compliance testing. Description of all modulation schemes used in the product:

Module uses BPSK and O-QPSK with half-sine pulse shaping.