MANUAL Produkt:
Ersteller:
Loxone Air Transceiver-Modul Urlhardt, Johannes Manual Loxone Air Transceiver-Modul 1. Introduction 1.1. 1.2. Abbreviations and Acronyms Related Documents 2. Modul Overview 3. Specification 3.1. Electrical Characteristics 3.1.1. 3.1.2. 3.1.3. Absolute Maximum Ratings Power Supply RF Characteristics(1) 3.2. 3.3. Agency Certifications 4.1. 4.2. Revision History 4. 5. Physical/environmental Characteristics and Outline Soldering Profile United States (FCC) Innovation, Science and Economic Development Canada (ISED) Compliance statements Produkt:
Ersteller:
Loxone Air Transceiver-Modul Urlhardt, Johannes MANUAL 1. Introduction 1.1. Abbreviations and Acronyms ADC API DC DTR Analog-to-Digital Converter Application Programming Interface Direct Current Data Terminal Ready EEPROM Electrically Erasable Programmable Read-Only Memory ESD GPIO HAF HVAC HW I2C IEEE IRQ ISM JTAG MAC MCU NRE OEM OTA PA Electrostatic Discharge General Purpose Input/output High Frequency Heating, Ventilating, and Air Conditioning Hardware Inter-Integrated Circuit Institute of Electrical and Electronics Engineers Interrupt Request Industrial, Scientific, and Medical radio band Digital interface for debugging of embedded device, also known as IEEE 1149.1 standard interface Medium Access Control layer Microcontroller Unit. In this document it also means the processor, which is the core of a ZigBit module Network layer Original Equipment Manufacturer Over-The-Air upgrade Power Amplifier MANUAL Produkt:
Ersteller:
Loxone Air Transceiver-Modul Urlhardt, Johannes PCB PER RAM RF RPC Printed Circuit Board Package Error Ratio Random Access Memory Radio Frequency Reduced Power Consumption RTS/CTS Request to Send/ Clear to Send RX SMA SoC SPI SW TTM TX UART USART USB ZigBee, ZigBee PRO 802.15.4 Receiver Surface Mount Assembly System on Chip Serial Peripheral Interface Software Time-To-Market Transmitter Universal Asynchronous Receiver/Transmitter Universal Synchronous/Asynchronous Receiver/Transmitter Universal Serial Bus Wireless networking standards targeted at low-power applications The IEEE 802.15.4-2003 standard applicable to low-rate wireless Personal Area Network 1.2. Related Documents
[1] IEEE Std 802.15.4-2003 IEEE Standard for Information technology - Part 15.4 Wireless Medium Access Control
(MAC) and Physical Layer (PHY) Specifications for Low-Rate Wireless Personal Area Networks (LR-WPANs).
[2] AT86RF212B Datasheet in http://www.atmel.com/devices/AT86RF212B.aspx?tab=documents. MANUAL Produkt:
Ersteller:
Loxone Air Transceiver-Modul Urlhardt, Johannes 2. Modul Overview The Loxone Air Transceiver-Modul is a low power IEEE 802.15.4/6LoPAN module for Loxone Air Smart Home Products. MANUAL 3. Specification 3.1. Electrical Characteristics 3.1.1. Absolute Maximum Ratings Produkt:
Ersteller:
Loxone Air Transceiver-Modul Urlhardt, Johannes Parameter Voltage on any pin, except RESET with respect to ground Input RF level Current into VCC pins Minimum
-0.3 V Maximum 3.6 V (VDD MAX)
+10dBm 200mA Notes:
1. Absolute Maximum Ratings are the values beyond which damage to the device may occur. Under no circumstances must the absolute maximum ratings given in this table be violated. Stresses beyond those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress rating only. Functional operation of the device at these or other conditions, beyond those indicated in the operational sections of this specification, is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. 2. Attention! The Loxone Air CPU Module is an ESD-sensitive device. Precaution should be taken when handling the device in order to prevent permanent damage. 3.1.2. Power Supply Parameter Supply voltage, VDD Range 1.8 to 3.6 Unit V MANUAL 3.1.3. RF Characteristics(1) Parameter Condition Frequency band FCC and Industry Canada(2) Numbers of channels (FCC and Industry Canada) Channel spacing (FCC and Industry Canada) Frequency band ETSI (European Union)(2) Number of channels (European Union) Channel spacing (European Union) Produkt:
Ersteller:
Loxone Air Transceiver-Modul Urlhardt, Johannes Range 902 928 10 2 863 - 870 4 1
-103 Unit MHz MHz MHz MHz dBm dBm Transmitter output power Adjusted in 36 steps
-25 to +11 Receiver sensitivity On-air data rate PER = 1%
40 up to 250 Kbps TX output/ RX input nominal impedance Note 1: For detailed characteristics, refer to [2]. For balanced 50 Note 2: Appropriate FW (Register selection) must be used for operating this Module in United States and Canada. Note 3: Range measured is Line of Sight and at 10ft elevation from Ground at different combinations of orientations of transmitter and receiver, with special conditions were there is minimal or no RF interference from other sources. 3.2. Physical/environmental Characteristics and Outline Parameters Size Value Comments 22.9 x 14.9 mm Operating temperature range
-40C to +85C
-40C to +85C operational MANUAL Produkt:
Ersteller:
Loxone Air Transceiver-Modul Urlhardt, Johannes 3.3. Soldering Profile The J-STD-020C-compliant soldering profile is recommended according to the following table. Profile Feature Average ramp-up rate (217C to peak) Preheat temperature 175C 25C Temperature maintained above 217C Green Package 3C/s max. 180s max. 60s to 150s Time within 5C of actual peak temperature 20s to 40s Peak temperature range Ramp-down rate Time within 25C to peak temperature 260C 6C/s max 8 minutes MANUAL 4. Agency Certifications 4.1. United States (FCC) Produkt:
Ersteller:
Loxone Air Transceiver-Modul Urlhardt, Johannes This equipment complies with Part 15 of the FCC rules and regulations. To fulfill FCC Certification requirements, an OEM manufacturer must comply with the following regulations:
1. Modules must be installed by original equipment manufacturers (OEM) only. 2. The module must only be operated with antennas adhering to the requirements defined in section Supported Antennas. 3. The Loxone Air Transceiver-Modul modular transmitter must be labeled with its own FCC ID number, and, if the FCC ID is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following:
IMPORTANT: Contains FCC ID: 2ARRV-000375. This equipment complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation (FCC 15.19). Installers must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance. This device is approved as a portable device with respect to RF exposure compliance, and may only be marketed to OEM installers. IMPORTANT: Modifications not expressly approved by this company could void the user's authority to operate this equipment (FCC section 15.21). IMPORTANT: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense (FCC section 15.105). MANUAL Produkt:
Ersteller:
Loxone Air Transceiver-Modul Urlhardt, Johannes 4.2. Innovation, Science and Economic Development Canada
(ISED) Compliance statements This device complies with ISED licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. This equipment complies with radio frequency exposure limits set forth by Industry Canada for an uncontrolled environment. Cet quipement est conforme aux limites d'exposition aux radiofrquences dfinies par Industrie Canada pour un environnement non contrl. CAUTION: Any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. The OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed (for example, digital device emissions, PC peripheral requirements, etc.). This Module is labelled with its own IC ID. If the IC ID Certification Number is not visible while installed inside another device, then the device should display the label on it referring the enclosed module. In that case, the final end product must be labelled in a visible area with the following:
Contains Transmitter Module IC: 24564-000375 OR Contains IC: 24564-000375 Ce module est tiquet avec son propre ID IC. Si le numro de certification IC ID n'est pas visible lorsqu'il est install l'intrieur d'un autre appareil, l'appareil doit afficher l'tiquette sur le module de rfrence ci-joint. Dans ce cas, le produit final doit tre tiquet dans un endroit visible par le texte suivant:
Contains Transmitter Module IC: 24564-000375 OR Contains IC: 24564-000375 4.3. Supported Antennas The FCC compliance testing of the Loxone Air Transceiver-Modul has been carried out using the W5012 antenna from PulseLarsen Antennas. This antenna has an omnidirectional radiation pattern at an antenna gain of 2 dBi. In order to be allowed to use the module without re-certification, the product incorporating MANUAL Produkt:
Ersteller:
Loxone Air Transceiver-Modul Urlhardt, Johannes the Loxone Air Transceiver-Modul module must either use the antenna mentioned above or must use an antenna with an omnidirectional radiation pattern and a gain being less than or equal to 2 dBi. MANUAL 5. Revision History Produkt:
Ersteller:
Loxone Air Transceiver-Modul Urlhardt, Johannes Doc. Rev. 1.0 Date 13/09/2018 Comments Initial document release