Adjusting Color Temperature (CCT) Copy and Paste Copy and Paste Cont. Copy and Paste Cont. Calibration CCT UP SELECT SCAN SELECT COPY TARGET PASTE CALIBRATION CCT DOWN Increasing the Color Temperature The color temperature can be adjusted from 2700K to 4200K in increments of 100K Press the CCT UP key to increase the color temperature The selected color temperature is shown in the display Decreasing the Color Temperature The color temperature can be adjusted from 4200K to 2700K in increments of 100K Press the Color Temperature DOWN key to decrease the color temperature The selected color temperature is shown in the display SCAN SELECT COPY TARGET PASTE CALIBRATION Selecting the Lamp to Copy Using the SCAN SELECT button, select the light to be copied The active lamp will ash To access another lamp in the wireless network, press SELECT again (the next lamp in the network will ash) Continue to press SELECT until the desired lamp ashes Copy a Lumenetix Lamp Use the Gray Card included in the Light Commissioning Tool COPY HOLD 2 SEC Hold the Gray Card in the center of the beam of the lamp to be copied. The ideal distance from the lamp is 4 feet (120 cm) Aim the light commissioning tool at the center of the Gray Card Press and hold COPY for two seconds. The Display will read Copy TARGET SCAN SELECT COPY TARGET PASTE CALIBR A TION Select the Target Lamp Press the TARGET button The active lamp will blink green To target a different lamp in the wireless network, continue to press TARGET until the desired lamp blinks green PASTE HOLD 2 SEC SCAN SELECT COPY TARGET PASTE CALIBRATION Paste Use the Gray Card included in the Light Commissioning Tool Hold the Gray Card in the center of the beam of the lamp to be pasted. The ideal distance from the lamp is 4 feet (120 cm) The distance that the gray card was held from the lamp that was copied should be equal to the distance that the gray card is held from the lamp to be pasted Aim the light commissioning tool at the center of the Gray Card Press and hold PASTE for two seconds. The Display will read Paste Keep the Light Commissioning Tool steadily pointed at the Gray Card until the lamp ashes twice, indicating that the operation is complete The brightness and color temperature will be shown in the display SCAN SELECT COPY TARGET PASTE CALIBR A TION CALIBRATION Press the SELECT button to access the active lamp in the network The active lamp will ash To access other lamps in the wireless network, continue to press SELECT until the desired lamp blinks amber Simultaneously press the COPY and PASTE buttons The lamp will begin calibration of the LEDs Upon completion the lamp will ash twice Introduction Inserting the Batteries Network Scan Select a Lamp Lamp On and Off Dimming SCAN / SELECT SCAN SELECT BRIGHTNESS UP POWER DISPLAY CCT UP BRIGHTNESS DOWN CCT DOWN COPY TARGET PASTE CALIBR A TION PASTE COPY TARGET REMOTE CONTROL Light Commissioning Tool Functions Wirelessly controls araya lamp power on/off, brightness, and color temperature Copy and Paste copy a Lumenetix lamp and paste it onto a Lumenetix lamp Calibration Compensates for different LED aging characteristics 3 x AAA Remove the battery case on the back of the remote control by pushing the tab in and sliding the cover down Insert 3 AAA batteries ensuring that the positive and negative terminals are correctly matched Replace the battery case SCAN SELECT COPY TARGET PASTE CALIBRATION HOLD 2 SEC SCAN SCAN SELECT SELECT Scan the Wireless Network to Discover Lamps Aim the remote control at the lamp(s) SCAN SELECT and press and hold SELECT until the display indicates that the light commissioning tool is scanning the network to discover all lamps After a few seconds, the active lamp will ash LAMP ON / OFF The display indicates the quantity of lamps SCAN SELECT discovered on the network CCT 3000K DIM 100%
SCAN SELECT COPY TARGET PASTE CALIBRATION SELECT SCAN SELECT SCAN SELECT COPY TARGET PASTE CALIBR A TION LAMP ON / OFF SCAN SELECT CCT 3000K DIM 100%
SCAN SELECT COPY TARGET PASTE CALIBRATION BRIGHTNESS UP BRIGHTNESS DOWN The active lamp in the network ashes in Press the POWER button and the selected lamp Network Scan will turn on To access another lamp in the network, press SELECT again. The next lamp in the network will ash. Continue to press SELECT until the desired lamp ashes The display will update to indicate the lamp within the network The brightness and color temperature will be shown in the display To turn the lamp off, press the POWER button If the lamp does not light, check the dimming level and adjust to the desired brightness (see next page) Increasing the Brightness The brightness can be adjusted from 5% to 100% in increments of 1%
Press the brightness UP key to increase the brightness The selected dimming level is shown in the display Decreasing the Brightness The lamp can be dimmed from 100% to 5% in increments of 1%
Press the brightness DOWN key to dim the lights The selected dimming level is shown in the display Instruction Manual Light Commissioning Tool Model Number LCT Zero For assistance with the operation of the Light Commissioning Tool, please visit www.lumenetix.com Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation. FCC ID: Q8A-LCT001