FCC ID: 2A7ZK-LAXBLCC Lumos Charging Cradle

CHARGING CRADLE GUIDE CHARGING FIREFLY When the battery is low, place your Firefly into the Charging Cradle and connect it to a power source. A red LED light should appear indicating its charging. Firefly is fully charged when the red LED light on Firefly turns green. It takes roughly 5 hours for a full charge. Note: Firefly is Qi-compatible and can also be charged with other Qi wireless chargers. FIREFLY CHARGING INDICATORS The Lumos Firefly has a small LED indicator to convey different information. Please note the colours below and the corresponding message. LED indicator Red LED light - Firefly is charging. Green LED light - Firefly is fully charged. Yellow LED light - Firefly has temporarily paused charging to allow it to charge within acceptable operating temperatures*. TURN YOUR CRADLE INTO A SHEEP ~ BAAA The Charging Cradle comes with an additional set of feet to add some character. Watch it turn into an alien-sheep-thingy by attaching the set of feet supplied. DISCOVER MORE FEATURES To attach, gently peel off the default flat rubber base from underneath. Remove the adhesive protector from the feet and carefully stick them to the base of the Charging Cradle. The feet were designed with the longer feet in front, but feel free to orient them however works best for you. For more information, visit firefly.lumoshelmet.co

*For optimal charging, charge in ambient temperatures of <=30C. If charging gets too hot, Firefly will temporarily stop charging to protect itself from overheating. Charging will automatically resume once it has cooled down sufficiently. For more information, visit firefly.lumoshelmet.co For more information, visit firefly.lumoshelmet.co SPECIFICATION OF RADIO TRANSMISSION Product: Lumos Charging Cradle Model Number: LAXBL-CC Operating frequency: 115kHz - 205kHz Max. RF output power: 7.2dBA/m Hereby, Lumos Labs International Pte Ltd. declares that the radio equipment type Lumos Charging Cradle is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: lumoshelmet.co/EU_DOC IC Statement This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic DevelopmentCanadas licence-exempt RSS(s). Operation is subject to the following two conditions:

(1) This device may not cause interference.

(2) This device must accept any interference, including interference that may cause undesired operation of the device. The term IC: before the certification/registration number only signifies that the Industry Canada technical specifications were met. This product meets the applicable Industry Canada technical specifications. ICet appareil contient des metteurs / rcepteurs exempts de licence conformes aux RSS (RSS) d'Innovation, Sciences etDveloppement conomique Canada. L'exploitation est autorise aux deux conditions suivantes

: (1) l'appareil ne doit pasproduire de brouillage,et (2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. L'metteur/rcepteur exempt de licence contenu dans le prsent appareil est conforme auxCNR d'Innovation, Sciences et Dveloppement conomique Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes :

(1) L'appareil ne doit pas produire de brouillage;

(2) L'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre lefonctionnement. This transmitter must not be co-located or operating in conjunction with any other antenna ortransmitter. This equipment should be installed and operated with a minimum distance of 20centimeters between the radiator and your body. Cet metteur ne doit pas tre Co-plac ou ne fonctionnant en mme temps qu'aucune autre antenne oumetteur. Cet quipementdevrait tre install et actionn avec une distance minimum de 20 centimtres entre le radiateur et votre corps. FCC - Statement Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-- Reorient or relocate the receiving antenna.

-- Increase the separation between the equipment and receiver.

-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-- Consult the dealer or an experienced radio/TV technician for help This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions (1)this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Importer in Switzerland:

Bucher et Walt SA Route de Soleure 8 CH-2072 St-Blaise Switzerland

+41 32 755 95 00 Importer in Canada:

Cycles Lambert Inc. 1000 Rue des Riveurs Lvis QC G6Y 9G3 Canada Importer in the USA:

Lumen Labs Inc. 4550 New Linden Hill Road, Suite 201, Wilmington, DE 19808

(617) 528-9968 Importer in the Netherlands:

Lumos Labs International Pte Ltd T.A.V HB VAT Services B.V. Kade 42A 3371 EP Hardinxveld-Giessendam Importer in Spain:

Athena Motor Ibrica, S.L. C\Joiers n17, Nave 7 08184- Palau Solit i Plegamans Barcelona Spain Importer in Denmark:

Sndergrd & Snner A/S Fabrikvej 3 8260 Viby J Denmark

+45 86 28 10 22 Importer in Norway:

Deler AS Hestehagen 4 NO-1448 Drbak Norway Importer in Finland:

Oy Hunterri Ab Lukkosepnkatu 4 Turku 20320 Finland Importer in the UK:

Lumos Labs International Pte Ltd Unit I, Hove Technology Centre St Josephs Close Hove East Sussex Importer in Germany:

GROFA Action Sports GmBH Otto-Hahn-Strae 17 Bad Camberg 65520 Germany

+49 6434 2008200 Importer in the Philippines:

Liberty & Co. 20 Talisay Road Barangay Forbes Park Makati City 1219 Philippines Importer in Singapore:

Kian Hong Cycle Pte Ltd 13 Kaki Bukit Road 1

#02-08 Eunos Technolink Singapore 415928

+65 6749 5787 Importer in Malaysia:

KHcycle Malaysia Sdn Bhd No. 9, Jalan PJU 3/48, Sunway Damansara Technology Park, 47810 Petaling Jaya, Selangor, Malaysia

+603 7865 2188 Importer in Italy:

ATHENA S.p.a. Via Delle Albere, 13 36045 Alonte Vicenza Italy sportech.support@athena.eu Importer in the Czech Republic:

Schindler, spol. s r.o. tpnkovick 950 / 23, Kravae, 74721 Czechia info@schindler.cz Importer in Indonesia:

PT. KHcycle Inodonesia Internasional Ruko the Prominence, Jl. Jalur Sutera 38D, No. 5 Alam Sutera -

Tangerang City 15143 Indonesia

+6222-30052581 The full text of the UK declaration of conformity is available at the following internet address: https://lumoshelmet.co/UK_DOC

Lumos Labs International Pte Ltd 2022.11.25 Eurofins Electrical and Electronic Testing NA, Inc. 914 W. Patapsco Avenue Baltimore, MD 21230 USA RE: LETTER OF AGENT AUTHORIZATION EUT NAME: Lumos Charging Cradle Trademark: LUMOS MODEL : LAXBL-CC FCC ID: 2A7ZK-LAXBLCC To Whom It May Concern:

We, the undersigned, hereby authorize Shenzhen BCTC Testing Co., Ltd to act on our behalf in all matters relating to application for equipment authorization, including the signing of all documents relating to these matters. We also hereby certify that no party to the application authorized hereunder is subject to the denial of benefits, including FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C.853(a). This agreement expires one year from the current date. Sincerely, Clients signature:

Clients name / title : Bilal Raja / Head of Product Contact information / address: 11 Collyer Quay, #17-00, The Arcade, Singapore 049317, Singapore

(Lumos Labs International Pte Ltd)

(2023.2.23) Eurofins Electrical and Electronic Testing NA, Inc. 914 West Patapsco Avenue Baltimore, MD 21230 RE: Attestation Statements Part 2.911(d)(5)(i) request for FCC ID: 2A7ZK-LAXBLCC

[Lumos Labs International Pte Ltd] (the applicant) certifies that the equipment for which authorization is sought is not covered equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Sincerely, Clients signature:

Clients name / title : Bilal Raja / Head of Product

(Lumos Labs International Pte Ltd)

(2023.2.23) Eurofins Electrical and Electronic Testing NA, Inc. 914 West Patapsco Avenue Baltimore, MD 21230 RE: Attestation Statements Part 2.911(d)(5)(ii) request for FCC ID: 2A7ZK-LAXBLCC

[Lumos Labs International Pte Ltd] (the applicant) certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List as an entity producing covered equipment. Clients signature:

Clients name / title : Bilal Raja / Head of Product

Lumos Labs International Pte Ltd 2023.01.04 Eurofins Electrical and Electronic Testing NA, Inc. 914 W. Patapsco Avenue Baltimore, MD 21230 USA RE: CONFIDENTIALITY REQUEST FOR EUT NAME: Lumos Charging Cradle Trademark: LUMOS MODEL : LAXBL-CC FCC ID: 2A7ZK-LAXBLCC To Whom It May Concern:

This letter serves as an official request for confidentiality under sections 0.457 and 0.459 of CFR 47. We have requested that the

- Block Diagram

- Schematics

- Operational Description required to be submitted with this application be permanently withheld from public review. The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. Please contact me if there is any information you may need. Sincerely, Clients signature:

Clients name / title : Bilal Raja / Head of Product Contact information / address: 11 Collyer Quay, #17-00, The Arcade, Singapore 049317, Singapore

Lumos Labs International Pte Ltd U.S. Agent Designation for Service of Process

(Applicant and U.S. Agent are Separate Parties) TO:

Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 ATTENTION: FCC Certification Section 2.911(d)(7) Information Designated U.S. Agent Company Name: Baihetian Innovative Solutions FRN: 0033401605 Contact Name: Kenneth Young Street Address: 6837 Chase Rd City/Province/Zip: Dearborn, MI 48126 Telephone No: 313-395-3113 Email: ken.young@baihetiansolutions.com This letter is to confirm that we (the Designated U.S. Agent) have accepted the responsibility to act as the Designated U.S. Agent for Service of Process as required by section 47 CFR 2.911(d)(7) on behalf of the Applicant noted below. U.S. Agent Signature:

Date: Feb 22, 2023 Signed by (Printed Name/Title): Kenneth Young/ Manager The Applicant acknowledges that they must maintain an agent for no less than one year after terminating all marketing and importation OR the conclusion of any Commission-related proceeding involving the equipment. The applicant further acknowledges their responsibility to inform the FCC whenever the Designated U.S. Agent information above changes. Applicant Company name: Lumos Labs International Pte Ltd Grantee Code: 2A7ZK FCC ID: 2A7ZK-LAXBLCC Contact Name: Bilal Raja Street Address: 11 Collyer Quay, #17-00, The Arcade, City/Province/Zip: Singapore 049317, Singapore Telephone No: +60 11-2110 9192 Email: support@lumoshelmet.co Applicant Signature:

Date: 2023/02/22 Signed by (Printed Name/Title): Bilal Raja / Head of Product